-
Network Analysis Module Command Reference, 4.1
-
About This Guide
-
Command-Line Interface
-
CLI Commands - alarm event - ip http secure install certificate
-
NAM CLI Commands: ip http secure port - monitor nbar
-
NAM CLI Commands: monitor matrix - preferences
-
NAM CLI Commands: esp-null-heuristic - show hosts
-
NAM CLI Commands: show inventory - show rmon buffer
-
NAM CLI Commands:show rmon channels - web-user
-
NAM Maintenance Partition CLI
-
Acronyms
-
NAM CLI Command - Platform Matrix
-
Index
-
Feedback
Table Of Contents
NAM CLI Commands:
show rmon channels - web-userwaas export server-filter-list
waas import server-filter-list
NAM CLI Commands:
show rmon channels - web-user
This chapter describes the following NAM CLI commands:
•
snmp
•
•
•
show rmon channels
To display the RMON channels, use the show rmon channels command.
show rmon channels [control-index]
Note
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.
Examples
This example shows how to display the RMON channels:
Root@localhost# show rmon channels46303Related Commands
rmon buffer
rmon channel
rmon filtershow rmon filters
To display the RMON filters, use the show rmon filters command.
show rmon filters [control-index]
Note
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.
Examples
This example shows how to display the RMON filters:
Root@localhost# show rmon filters46303Related Commands
rmon buffer
rmon channel
rmon filtershow router
show rxcounters
Note
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported only on NME-NAM-80S and NME-NAM-120S devices.
Examples
This example shows how to display the router information:
Root@localhost# show routershow rxcounters
To display the RX data counters, use the show rxcounters command.
show rxcounters
Note
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported only on NAM-1 and NAM-2 devices.
Examples
This example shows how to display the RX data counters:
Root@localhost# show rxcountersdata port 1 rx pkt count: 1524112data port 2 rx pkt count: 1115show snmp
To display the SNMP parameters, use the show snmp command.
show snmp
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to display the SNMP parameters:
Root@localhost# show snmpSNMP Agent: mynam.cisco.com 209.265.200.225SNMPv1: EnabledSNMPv2C: EnabledSNMPv3: Disabledcommunity private writecommunity public readtrap community public 112.10.17.237trap community public 112.10.17.244sysDescr Network Analysis Module (WS-SVC-NAM-2), Version 4.1(1)Copyright (c) 1999-2007 by cisco Systems, Inc.sysObjectID workgroup.1.3.1.1.2.291sysContact engineersysName mynamsysLocation RMON LabRelated Commands
show syslog-settings
To display the NAM system log settings, use the show syslog-settings command.
show syslog-settings
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to display the NAM system log settings:
Root@localhost# show syslog-settingsMIB threshold events: LocalVoice threshold events: LocalSystem alerts (debug): LocalRelated Commands
show system-alerts
To display NAM failures or problems, use the show system-alerts command.
show system-alerts
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to display the NAM system alerts:
Root@localhost# show system-alertsJan 1 15:07:31 mynam scpd: scpd: 0x10/44 -> 0x15/0, len 18, op 0x14a, len2, flags 0(), seq 65443, ver 0Jan 1 15:07:31 mynam scpd: scpd: SCP PC Blade REQ from 0x10/44.Jan 1 15:07:31 mynam scpd: scpd: sub-opcode 6, status 45.Jan 1 15:07:31 mynam scpd: scpd: SCP PC Shutdown.Jan 1 15:07:33 mynam scpd: scpd: shutdown of NAM!Jan 1 15:07:35 mynam rmond[595]: rmond: received QUIT signal! Exiting!Jan 1 15:07:38 mynam polld: Terminating polld.Jan 1 15:07:42 mynam configd: SIGTERM recieved.Jan 1 15:07:42 mynam configd: Terminating with success.Jan 1 00:02:43 mynam scpd: scpd: 0x10/1 -> 0x15/0, len 18, op 0x14a, lenRelated Commands
show tech-support
To display technical support information, use the show tech-support command.
show tech-support
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to display the NAM technical support information:
Root@localhost# show tech-supportPID TTY STAT TIME COMMAND1 ? S 0:08 init2 ? SW 0:00 [keventd]3 ? SWN 0:00 [ksoftirqd_CPU0]4 ? SWN 0:00 [ksoftirqd_CPU1]5 ? SW 0:00 [kswapd]6 ? SW 0:00 [bdflush]7 ? SW 0:05 [kupdated]238 ? S 0:00 /usr/local/nam/bin/scpd -l -d/var/log/scpd246 ? SW 0:10 [kjournald]474 ? S 0:01 syslogd -m 0477 ? S 0:00 klogd -2501 ? S 0:00 /usr/sbin/atdshow time
To display NAM time zone or time synchronization settings, use the show time command.
show time
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to display the NAM time settings:
Root@localhost# show timeNAM synchronize time to: SwitchTimezone configured on the switch: PDTCurrent system time: Thu May 1 09:29:49 GMT+8 2003Related Commands
show trap-dest
To display all of the NAM trap destinations, use the show trap-dest command.
show trap-dest [trap-index]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to display the NAM trap destinations:
Root@localhost# show trap-destTrap index: 23370Community: publicAddress: 172.20.98.136UDP port: 162 (00a2)Owner: LocalMgrRoot@localhost#Related Commands
show version
To display the NAM version information, use the show version command.
show version
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to display the NAM version information:
Root@localhost# show versionNAM application image version: 4.1(1)Maintenance image version: 2.1(2)NAM Daughter Card Micro code version: 1.34.1.28 (NAM)BIOS Version: 4.0-Rel 6.0.9Installed patches:Wed Jun 6, 16:10:27 2007 Patch: nam-dev-patch-3-6-1 Description: Development patch for NAMRoot@localhost#Related Commands
show waas data-source
To display the WAAS devices configured on the NAM device, use the show waas data-source command.
show waas data-source [datasrc-index]
Syntax Description
Defaults
The default behavior is to show all WAAS data sources unless a specific data source index is specified.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
The show waas data-source command displays information about WAAS data sources currently configured on the NAM.
Examples
The following example shows the system inventory information:
root@nam.cisco.com# show waas data-sourceroot@nam.cisco.com#show waas device
To display the WAAS devices configured on the NAM device, use the show waas device command.
show waas device [ip-address]
Syntax Description
Defaults
The default behavior is to show all WAAS devices unless IP address is specified.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
The following example shows the system inventory information:
root@nam.cisco.com# show waas deviceroot@nam.cisco.com#show waas server filters
To show WAAS server filter list, use the show waas server filters command.
show waas server filters
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
The following example shows how to display the waas server filters.
root@nam.cisco.com# show waas server filters10.0.0.2show web-publication
To display the web publication hosts configuration information, use the show web-publication command.
show web-publication
Syntax Description
This command has no keywords or arguments.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to display the web user information:
Root@localhost# show web-publicationWeb publication: enabledAllowed hosts:Access code:Alarm screens: disabledReport screens: enabledVoice screens: enabledRMON screens: enabledRelated Commands
show web-users
To display the web user information, use the show web-users command.
show web-users [user-name]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to display the web user information:
Root@localhost# show web-users adminUser: admin----------------------------Account management: EnabledSystem config: EnabledCapture: EnabledAlarm config: EnabledCollection config: EnabledCollection view: EnabledConsoleRelated Commands
shutdown
To shut down the NAM, use the shutdown command.
shutdown
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to shut down the NAM:
Root@localhost# shutdownShut down the NAM? (y/n) [n]: nRelated Commands
snmp
To configure NAM system MIB objects, use the snmp command.
snmp community community-string { ro | rw }
snmp delete community community-string
snmp contact contact-string
snmp location location-string
snmp name name-string
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to configure NAM system MIB objects:
Root@localhost# snmp community askdfhtjlks.01` contact george location frisco, name alRelated Commands
supervisor address
To set the local supervisor engine address to the NAM, use supervisor address command. To return the NAM back to the default where the NAM learns the supervisor engine address during the NAM bootup process, use the no supervisor address command.
supervisor address string
no supervisor address
Note
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Usage Guidelines
This command is supported only on NAM-1 and NAM-2 devices.
The local supervisor engine address is sent to the NAM by the supervisor engine during the NAM bootup process. In some specific network configurations, the supervisor engine address that the NAM expected to receive may not exist or cannot be reached by the NAM. This command allows you to set a NAM-reachable supervisor address.
This command is supported in NAM-1 and NAM-2 only.
Examples
This example shows how to set the local supervisor engine address to the NAM as 123.54.106.12:
root@localhost.cisco.com# supervisor address 123.54.106.12syslog
To enter the system log subcommand mode, and then configure system logging for the NAM, use the syslog command.
syslog
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Usage Guidelines
When you enter the system log subcommand mode, the following commands are available:
•
•
•
•
•
•
Examples
This example shows how to configure system logging for the NAM:
Root@localhost# syslogroot@localhost.cisco.com(sub-syslog)#Related Commands
syslog mib
To capture NAM MIB alarms and send them to the system log, use the syslog mib command from the syslog subcommand mode.
syslog mib [local enable | disable] [remote enable | disable]
Syntax Description
local enable | disable
(Optional) Enables or disables local MIB alarms.
remote enable | disable
(Optional) Enables or disables remote MIB alarms.
Defaults
This command has no default settings.
Command Modes
Syslog subcommand mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to configure the NAM to capture MIB alarms:
root@localhost# syslogEntering into subcommand mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@localhost(sub-syslog)# mib local enableroot@localhost(sub-syslog)# exitNAM syslog settings updated successfully.root@localhost# show syslogMIB threshold events: LocalVoice threshold events: LocalSystem alerts (info): LocalRelated Commands
alarm event
show alarm event
show autostart
show syslog-settings
syslog
syslog remote-server
web-user
syslog remote-server
To capture NAM remote server alarms, use the syslog remote-server command from the syslog subcommand mode.
syslog remote-server disable | [server1 [server2] [server3] [server4] [server5]
Syntax Description
disable
Disables remote server event logging.
server1 server2 server3 server4 server5
(Optional) Specifies the remote server.
Defaults
This command has no default settings.
Command Modes
Syslog subcommand mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to configure the NAM to capture remote server alarms:
Root@localhost<sub-syslog># syslogEntering into subcommand mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.Root@localhost<sub-syslog># voice remote enableRoot@localhost<sub-syslog># syslog remote-server 172.20.98.136Root@localhost<sub-syslog># exitNAM syslog settings updated successfully.Related Commands
alarm mib
show alarm event
show autostart
show syslog-settings
syslog
syslog remote-server
web-usersyslog system
To capture NAM system alarms, use the syslog system command from the syslog subcommand mode.
syslog system debug enable | disable local enable | disable remote enable | disable
Syntax Description
Defaults
This command has no default settings.
Command Modes
Syslog subcommand mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to configure the NAM to capture system alarms:
Root@localhost# syslog system local enableRelated Commands
alarm mib
show alarm event
show autostart
show syslog-settings
syslog
syslog remote-server
web-user
syslog voice
To configure system logging for voice threshold events from the syslog subcommand mode, use the syslog voice command.
syslog voice local enable | disable remote enable | disable
Syntax Description
local enable | disable
Enables or disables local voice alarms.
remote enable | disable
Enables or disables remote voice alarms.
Note
Defaults
This command has no default settings.
Command Modes
Syslog subcommand mode
Usage Guidelines
This command is supported only on NAM-1, NAM-2, NME-NAM-80S, and NME-NAM-120S devices and Cisco NAM 2200 Series appliances.
Examples
This example shows how to configure the NAM to capture voice alarms:
root@hostname.cisco.com<sub-syslog># syslog voice local enableroot@hostname.cisco.com# show optionsART mib: EnabledVoice monitoring:Enabledroot@hostname.cisco.com#Related Commands
alarm mib
show alarm event
show patches
show syslog-settings
syslog remote-server
terminal
To set the number of lines on a screen for this session, use the terminal command.
terminal editor [enable | disable]
terminal length length
terminal mode { 0 | 1}
Syntax Description
editor [enable | disable]
(Optional) Enables or disables the NAM CLI command editing.
length length
Sets the number of lines per screen for a session.
mode { 0 | 1}
Sets the terminal mode.
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to set the number of lines on a session's screen:
root@localhost# terminal length 24Terminal length for this session set to 24.Related Commands
time
To enter the time configuration subcommand mode, and then configure NAM system time settings, use the time command.
time
Syntax Description
This command has no arguments or keywords.
Defaults
This command has no default settings.
Command Types
Switch command
Command Modes
Privileged
Usage Guidelines
This command is supported on all NAM platforms.
When you enter the time configuration subcommand mode, the following commands are available:
•
•
•
•
•
This command is specific to the NAM software release running on network modules in the Cisco 2600, 3600, and 3700 routers.
Examples
This example shows how to configure system time settings on the NAM to synchronizes the time with the switch:
root@hostname.cisco.com# timeEntering into subcommand mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@hostname.cisco.com(sub-time)# ?? - display helpcancel - discard changes and exit from subcommand modeexit - exit from subcommand modehelp - display helpsync - synchronize NAM system time with switch or ntproot@hostname.cisco.com(sub-time)# sync switchroot@hostname.cisco.com(sub-time)# exitSuccessfully updated NAM system time settings.NOTE:You have configured the NAM synchronize time to the switch.For this change to take effect, set the time from the switch orreset the NAM.root@hostname.cisco.com# show timeNAM synchronize time to: SwitchTimezone configured on the switch:PSTSwitch time offset to UTC: 0Current system time: Thu Mar 20 09:23:14 GMT 2003This example shows how to configure system time settings on the NAM to synchronize the time with the NTP:
root@hostname.cisco.com# timeEntering into subcommand mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@hostname.cisco.com(sub-time)# sync ntp ntp01.cisco.com ntp02.cisco.comroot@hostname.cisco.com(sub-time)# exitSuccessfully updated NAM system time settings.root@hostname.cisco.com# show timeNAM synchronize time to: NTPNTP server1: ntp01.cisco.comNTP server2: ntp02.cisco.comCurrent system time: Thu Mar 20 09:23:36 GMT 2003root@hostname.cisco.com#Related Commands
traceroute
To trace the route to a network device, use the traceroute command.
traceroute [-I | n | v] [-f first_ttl] [-m max_ttl] [-p port] [-s src_addr] [-t tos] [-w waittime] destination host name | IP address [packetlen]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to trace a route to a network device named aragon:
root@localhost.cisco.com# traceroute -I -n -v -f first_ttl -p 5 -w 10 aragon 123.34.54.12root@localhost.cisco.com#trap-dest
To enter the trap destination subcommand mode and create or edit trap destinations on the NAM, use the trap-dest command. To remove a trap destination entry, use the no form of this command.
trap-dest
no trap-dest [control-index]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
When you enter the trap destination subcommand mode, the following commands are available:
•
•
•
•
•
•
Note
•
Examples
This example shows how to configure traps on the NAM:
root@hostname.cisco.com# trap-destEntering into subcommand mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@hostname.cisco.com(sub-trap-dest)# ?? - display helpaddress - set IP address (*)cancel - discard changes and exit from subcommand modecommunity - set community string (*)exit - exit from subcommand modehelp - display helpindex - set trap indexowner - set owner stringport - set UDP port(*) - denotes a mandatory field for this configuration.root@hostname.cisco.com(sub-trap-dest)# address 10.0.0.1root@hostname.cisco.com(sub-trap-dest)# community publicroot@hostname.cisco.com(sub-trap-dest)# exitTrap created successfully.root@hostname.cisco.com# show trap-destTrap index:48981Community: publicAddress: 10.0.0.1UDP port: 162 (00a2)Owner: monitorroot@hostname.cisco.com#Related Commands
alarm event
alarm mib
show alarm event
show autostart
show trap-destupgrade
To download and install a new maintenance image on the NAM, use the upgrade command.
upgrade ftp://user:passwd@host/full-path/filename
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
This example shows how to download and install a new maintenance image:
Root@localhost# upgrade ftp://alamo:ljljsdf@milton/dir65/abracadabr/dir65/upgrade_nowRoot@localhost#Related Commands
waas data-source
To enter the WAAS data source configuration subcommand mode and create a WAAS data source, use the waas data-source command. To remove a WAAS data source, use the no form of this command.
waas data-source <data-source-index>
no waas data-source
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
When you enter the data source configuration subcommand mode, the following commands are available:
•
•
•
•
•
•
Note
Examples
The following example shows how to configure a WAAS data source and how to remove a WAAS data source:
root@nam.cisco.com# waas data-sourceEntering into subcommand mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@nam.cisco.com(sub-waas-data-source)# device 10.0.0.1root@nam.cisco.com(sub-waas-data-source)# segment CoreWANroot@nam.cisco.com(sub-waas-data-source)# exitSuccessfully added WAAS CoreWAN segment data source.root@nam.cisco.com# show waas data-sourceIndex: 19Device Id: 2Name: WAE-10.0.0.1-CoreWANroot@nam.cisco.com# no waas data-source 19Deleted the data source successfully.waas device
To configure remote WAAS device, use the waas device command. To remove a remote WAAS device, use the no form of this command.
waas device <ip-address> [export-ppt]
no waas device <ip-address> [export-ppt]
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
The following examples show how to configure a WAAS device and how to remove a WAAS device:
root@nam.cisco.com# waas device 10.0.0.1Successfully added waas device.root@nam.cisco.com# show aas deviceId: 3Name: UnknownAddress: 10.0.0.1State: inactiveExport PTT: disabledroot@nam.cisco.com# no waas device 10.0.0.1Successfully deleted the waas device.waas export server-filter-list
To export waas server filter list to a remote host, use the waas export server-filter-list command.
waas export server-filter-list ftp://<username:<password>@<host>/<path>
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
The following example shows how to export the waas server filter list to a remote host:
root@nam.cisco.com# waas export server-filter-list ftp://joe@company.com//waas/configsroot@nam.cisco.com#waas import server-filter-list
To import the WAAS server filter list from a remote host, use the waas import server-filter-list command.
waas import server-filter-list ftp://<username:<password>@<host>/<path>/<file>
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
The following example shows how to import the waas server filter list from a remote host:
root@nam.cisco.com# waas import server-filter-list ftp://joe@company.com//waas/config/svrlistroot@nam.cisco.com#waas server filter
To add a WAAS server filter, use the waas import server-filter command. To remove a server filter use the no form of this command
waas server filter <ip-address>
no waas server filter <ip-address>
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
Examples
The following example shows how to add a WAAS server filter and how to remove a WAAS server filter:
root@nam.cisco.com# waas server filter 10.0.0.2Successfully added server filter.root@nam.cisco.com# no waas server filter 10.0.0.2root@nam.cisco.com#web-publication
To enable and set up a list of hosts that can view the NAM GUI monitoring displays without logging into the NAM, use the web-publication command. To remove web publishing from your configuration, use the no form of this command.
web-publication user-name
no web-publication
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
When you enter the web user subcommand mode, the following commands are available:
•
•
•
•
•
•
•
•
•
Examples
This example shows how to configure a host to receive web published reports from the NAM:
root@hostname.cisco.com# web-publicationEntering into subcommand mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@hostname.cisco.com(sub-web-publication)# ?root@hostname.cisco.com#Related Commands
web-user
To enter the web user configuration subcommand mode, and then configure local web users on the NAM, use the web-user command. To remove a web user from your configuration, use the no form of this command.
web-user
no web-user user-name
Syntax Description
Defaults
This command has no default settings.
Command Modes
Command mode
Usage Guidelines
This command is supported on all NAM platforms.
When you enter the web user subcommand mode, the following commands are available:
•
•
•
•
•
•
•
•
Examples
This example shows how to configure a NAM web user:
root@hostname.cisco.com# web-userEntering into subcommand mode for this command.Type 'exit' to come out of this mode.Type 'cancel' to discard changes and to come out of this mode.root@hostname.cisco.com(sub-web-user)# ?? - display helpaccount-mgmt - enable/disable account management privilegealarm-config - enable/disable alarm configuration privilegecancel - discard changes and exit from subcommand modecapture - enable/disable packet capture/decode privilegecollection-config - enable/disable collection configuration privilegeexit - exit from subcommand modehelp - display helpsystem-config - enable/disable system configuration privilegeuser-name - set username (*)(*) - denotes a mandatory field for this configuration.root@hostname.cisco.com(sub-web-user)# user-name fooroot@hostname.cisco.com(sub-web-user)# account-mgmt enableroot@hostname.cisco.com(sub-web-user)# exitNo password specified.Do you want specify password now (y/n) [n] yEnter password:Confirm password:User 'foo' created successfully.root@hostname.cisco.com# show web-users fooUser name: fooAccount management:EnabledSystem config: DisabledCapture: DisabledAlarm config: DisabledCollection config: DisabledCollection view: Enabledroot@hostname.cisco.com#Related Commands
