User Guide for Device Fault Manager 3.2 (With LMS 3.2)
Appendix C: Notification MIB
Download this chapter
Appendix C: Notification MIBAppendix C: Notification MIB
Download the complete book
User Guide for Device Fault Manager 3.2 - PDF of Entire BookUser Guide for Device Fault Manager 3.2 - PDF of Entire Book (PDF - 7 MB)
 Feedback

Table Of Contents

Notification MIB


Notification MIB

The CISCO-EPM-NOTIFICATION-MIB specifies the trap message format Device Fault Manager (DFM) uses to generate SNMP traps when an alert occurs. The trap includes the attributes of the alert and the events that caused the alert.

This topic includes the following information:

•MIB Definition

•cenAlarmEntry Object-Type—Definitions for Selected Attributes

The CISCO-EPM-NOTIFICATION-MIB is available on Cisco.com at

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

MIB Definition 

CISCO-EPM-NOTIFICATION-MIB DEFINITIONS ::= BEGIN


IMPORTS

    MODULE-IDENTITY,

    NOTIFICATION-TYPE,

    Integer32,

    Unsigned32,

    OBJECT-TYPE,

    OBJECT-IDENTITY

        FROM SNMPv2-SMI

    MODULE-COMPLIANCE,

    NOTIFICATION-GROUP,

    OBJECT-GROUP

        FROM SNMPv2-CONF

    TimeStamp,

    RowPointer

        FROM SNMPv2-TC

    SnmpAdminString

        FROM SNMP-FRAMEWORK-MIB

    InetAddressType,

    InetAddress

        FROM INET-ADDRESS-MIB

    Unsigned64

        FROM CISCO-TC

    ciscoMgmt

        FROM CISCO-SMI;


ciscoEpmNotificationMIB MODULE-IDENTITY

    LAST-UPDATED    "200901300000Z"

    ORGANIZATION    "Cisco Systems, Inc."

    CONTACT-INFO

            "Cisco Systems

            Customer Service


            Postal: 170 W Tasman Drive

            San Jose, CA 95134


            Tel: +1 800 553-NETS


            E-mail: tac@cisco.com"

    DESCRIPTION

        "Notifications directly from hardware and software and processed

        notifications from various management applications can be further

        processed and forwarded by still other management applications to 

        indicate the status of devices and software (managed objects).

        The status of these managed objects can be reported by traps.


        The CISCO-EPM-NOTIFICATION-MIB contains the trap structure which 

        carries the identity and status info of the managed object as

        analyzed by such an event processor. It is not possible for

        receivers of these traps to query the mib objects.


        A unique but optional feature of the application generating the 

        trap defined in this mib is the ability to contain multiple 

        partitions in the same system running the application. A 

        'Partition' is a logical grouping of a set of managed devices. 

        These devices can belong to only one partition at any given 

        time. The trap structure will contain information on the exact 

        partition number and the partition name of the device where it 

        resides.


        The need for trap generation is to enable multiple management

        applications in the network to have a consolidated view of the

        whole network of Cisco and non-Cisco devices."

    REVISION        "200901300000Z"

    DESCRIPTION

        "Added a new Notification ciscoEpmHealthNotificationAlarm to reflect

        the status of health and utilization related details of Managed Objects.    


         Added more attributes which are useful for the new Notification.


         Added new oid subtree ciscoEpmNotificationComputedVar under 
ciscoEpmNotificationMIBObjects

        to support the computed/derived variables described with cenAlarmMibVariable."

    REVISION        "200406070000Z"

    DESCRIPTION

        "Updated the cenAlarmEntry to include new attributes. The new

        attributes carries information that adds more value to the already

        existing trap structure.


        The Management application computes events for a device via 

        polling snmp mib objects on the device and/or by listening to 

        SNMP Traps. Multiple events on a single device roll up into what 

        is called an Alert - there can be only one alert for a given 

        device at any given time. The objects contained in the 

        cenAlarmEntry are the same for both Alert and Event based 

        notification. The attribute cenAlarmMode added in this revision

        of the mib can be used to distinguish between the Alert based and 

        event based notification.


        In case of event based notification, the cenAlertID would contain 

        the alert id, as computed by the management system, to which the 

        generated event has been rolled up. 


        Traps generated from systems that support mutiple Partition, the 

        cenPartitionNumber and cenPartitionName attributes will carry the

        exact partition details of the device for which the trap is 

        generated.


        Through the management application user interface, the user can 

        customize few attributes of the trap structure. Two attributes 

        included in this mib revision that allows the user to customize 

        each trap sent out are cenCustomerIdentification and 

        cenCustomerRevision.


        ciscoEpmNotificationObjectsGroup, ciscoEpmNotificationAlarm, and

        ciscoEpmNotificationMIBCompliance have been deprecated in this 

        revision.


        ciscoEpmNotificationAlarmRev1,

        ciscoEpmNotificationAlarmGroupRev1,

        ciscoEpmNotificationMIBComplianceRev1, 

        and ciscoEpmNotificationObjectsGroupRev1 have been newly created

        in this revision."

    REVISION        "200308210000Z"

    DESCRIPTION

        "Included imports for Integer32, Unsigned32, and

        NOTIFICATION-GROUP."

    REVISION        "200207281420Z"

    DESCRIPTION

        "Initial version of this MIB."

    ::= { ciscoMgmt 311 }


-- MIB Object Definitions


ciscoEpmNotificationMIBNotifs  OBJECT IDENTIFIER

    ::= { ciscoEpmNotificationMIB 0 }


ciscoEpmNotificationMIBObjects  OBJECT IDENTIFIER

    ::= { ciscoEpmNotificationMIB 1 }


ciscoEpmNotificationMIBConform  OBJECT IDENTIFIER

    ::= { ciscoEpmNotificationMIB 2 }


cenAlarmData  OBJECT IDENTIFIER

    ::= { ciscoEpmNotificationMIBObjects 1 }


ciscoEpmNotificationComputedVar  OBJECT IDENTIFIER

    ::= { ciscoEpmNotificationMIBObjects 2 }


cenAlarmTableMaxLength OBJECT-TYPE

    SYNTAX          Unsigned32 (1..4294967295)

    MAX-ACCESS      read-write

    STATUS          current

    DESCRIPTION

        "Maximum number of entries permissible in the cenAlarmTable."

    DEFVAL          { 1 } 

    ::= { cenAlarmData 1 }


cenAlarmTable OBJECT-TYPE

    SYNTAX          SEQUENCE OF CenAlarmEntry 

    MAX-ACCESS      not-accessible

    STATUS          current

    DESCRIPTION

        "A table containing the device identification and

        alarm value. The maximum number of entries permissible 

        in this table is defined by cenAlarmTableMaxLength. When 

        the number of entries in the table reaches the maximum 

        limit, the next entry would replace the oldest existing 

        entry in the table."

    ::= { cenAlarmData 2 }


cenAlarmEntry OBJECT-TYPE

    SYNTAX          CenAlarmEntry

    MAX-ACCESS      not-accessible

    STATUS          current

    DESCRIPTION

        "The information regarding a single device status alarm.

        An entry is created when an alarm is processed."

    INDEX           { cenAlarmIndex } 

    ::= { cenAlarmTable 1 }


CenAlarmEntry ::= SEQUENCE {

        cenAlarmIndex                    Unsigned32,

        cenAlarmVersion                  SnmpAdminString,

        cenAlarmTimestamp                TimeStamp,

        cenAlarmUpdatedTimestamp         TimeStamp,

        cenAlarmInstanceID               SnmpAdminString,

        cenAlarmStatus                   Integer32,

        cenAlarmStatusDefinition         SnmpAdminString,

        cenAlarmType                     INTEGER,

        cenAlarmCategory                 Integer32,

        cenAlarmCategoryDefinition       SnmpAdminString,

        cenAlarmServerAddressType        InetAddressType,

        cenAlarmServerAddress            InetAddress,

        cenAlarmManagedObjectClass       SnmpAdminString,

        cenAlarmManagedObjectAddressType InetAddressType,

        cenAlarmManagedObjectAddress     InetAddress,

        cenAlarmDescription              OCTET STRING,

        cenAlarmSeverity                 Integer32,

        cenAlarmSeverityDefinition       SnmpAdminString,

        cenAlarmTriageValue              Integer32,

        cenEventIDList                   OCTET STRING,

        cenUserMessage1                  SnmpAdminString,

        cenUserMessage2                  SnmpAdminString,

        cenUserMessage3                  SnmpAdminString,

        cenAlarmMode                     INTEGER,

        cenPartitionNumber               Unsigned32,

        cenPartitionName                 SnmpAdminString,

        cenCustomerIdentification        SnmpAdminString,

        cenCustomerRevision              SnmpAdminString,

        cenAlertID                       SnmpAdminString,

        cenAlarmObjectId                 OBJECT IDENTIFIER,

        cenAlarmObjectInstance           RowPointer,

        cenAlarmViolatedValue            Unsigned64,

        cenAlarmViolatedValueMantissa    Integer32

}


-- Alarm attributes


cenAlarmIndex OBJECT-TYPE

    SYNTAX          Unsigned32 (1..4294967295)

    MAX-ACCESS      not-accessible

    STATUS          current

    DESCRIPTION

        "A monotonically increasing integer for the sole

        purpose of indexing the attributes in 

        ciscoEpmNotificationMIBObjects. When the maximum value is 

        reached, this value wraps back to 1." 

    ::= { cenAlarmEntry 1 }


cenAlarmVersion OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..16))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The release version of this MIB. The version string will

        be of the form <major version>.<minorversion>." 

    ::= { cenAlarmEntry 2 }


cenAlarmTimestamp OBJECT-TYPE

    SYNTAX          TimeStamp

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The time when the alarm was raised." 

    ::= { cenAlarmEntry 3 }


cenAlarmUpdatedTimestamp OBJECT-TYPE

    SYNTAX          TimeStamp

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "Alarms persist over time and can have their field(s)

        change values. The last time a field(s) changed, this

        alarm is updated. The updated time denotes this time. 

        Each alarm is identified by the unique alarm instance 

        id, cenAlarmInstanceID." 

    ::= { cenAlarmEntry 4 }


cenAlarmInstanceID OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..20))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The Unique Alarm Instance ID." 

    ::= { cenAlarmEntry 5 }


cenAlarmStatus OBJECT-TYPE

    SYNTAX          Integer32 (1..250)

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The alarm status indicates the status of the alarm

        in integer value." 

    ::= { cenAlarmEntry 6 }


cenAlarmStatusDefinition OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..255))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The short description of the status of the alarm.

        The string is formatted in 

        '<integer>,<alarmStatus description>' tuples. The <integer>

        value is the same value that the 'cenAlarmStatus' 

        attribute holds. <alarmStatus description> contains one line

        description of the alarm status generated." 

    ::= { cenAlarmEntry 7 }


cenAlarmType OBJECT-TYPE

    SYNTAX          INTEGER  {

                        unknown(1),

                        direct(2),

                        indirect(3),

                        mixed(4)

                    }

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "unknown:  When the value for this attribute could not be

        determined.       

        direct:   Denotes an alarm generated by a set of events where 

        all events are reported by an observation(s) of a 

        managed object. 

        indirect: Denotes an alarm generated by a set of events where 

        all events were deduced or inferred by the status of 

        managed objects as determined by the network 

        management system. 

        mixed:    Denotes an alarm generated by a set of events which 

        were either direct or indirect." 

    ::= { cenAlarmEntry 8 }


cenAlarmCategory OBJECT-TYPE

    SYNTAX          Integer32 (1..250)

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The category of the alarm generated represented in

        integer value." 

    ::= { cenAlarmEntry 9 }


cenAlarmCategoryDefinition OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..255))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The short description of the category of the alarm

        generated. The String is formatted in 

        '<integer>,<alarmCategory description>' tuples. The <integer>

        value is the same value that the 'cenAlarmCategory' 

        attribute holds. <alarmCategory description> contains one 

        line description of the alarm category generated." 

    ::= { cenAlarmEntry 10 }


cenAlarmServerAddressType OBJECT-TYPE

    SYNTAX          InetAddressType

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The type of Internet address by which the server

        is reachable. The Server is the server 

        that is generating this trap." 

    ::= { cenAlarmEntry 11 }


cenAlarmServerAddress OBJECT-TYPE

    SYNTAX          InetAddress

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The IP Address or the DNS name of the Management

        Server that raised this alarm to be notified." 

    ::= { cenAlarmEntry 12 }


cenAlarmManagedObjectClass OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..255))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The class of the managed object for which this

        alarm was  generated. For example, Router, Switch, 

        GateKeeper and VoicePort." 

    ::= { cenAlarmEntry 13 }


cenAlarmManagedObjectAddressType OBJECT-TYPE

    SYNTAX          InetAddressType

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The type of Internet address by which the managed

        object is reachable." 

    ::= { cenAlarmEntry 14 }


cenAlarmManagedObjectAddress OBJECT-TYPE

    SYNTAX          InetAddress

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The IP Address or the DNS name of the Managed Object." 

    ::= { cenAlarmEntry 15 }


cenAlarmDescription OBJECT-TYPE

    SYNTAX          OCTET STRING (SIZE  (1..1024))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "A detailed description of the alarm." 

    ::= { cenAlarmEntry 16 }


cenAlarmSeverity OBJECT-TYPE

    SYNTAX          Integer32 (0..100)

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The alarm severity indicates the severity of the alarm

        in integer value." 

    ::= { cenAlarmEntry 17 }


cenAlarmSeverityDefinition OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..255))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The short description of the severity of the alarm

        generated. The String is formatted in 

        '<integer>,<alarmSeverity  description>' tuples. The <integer>

        value is the same value that the 'cenAlarmSeverity ' 

        attribute holds. <alarmSeverity description> contains one line

        description of the alarm severity generated." 

    ::= { cenAlarmEntry 18 }


cenAlarmTriageValue OBJECT-TYPE

    SYNTAX          Integer32 (0..100)

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "The triage value of an alarm is a hierarchical weighting value

        (applied by the application, and more importantly customizable 

        by the end  user) to allow an artificial form of evaluating 

        impact, interest, or other user-determined functions between 

        alarms. The value is a positive number or zero where zero 

        denotes an undetermined or uncomputable value." 

    ::= { cenAlarmEntry 19 }


cenEventIDList OBJECT-TYPE

    SYNTAX          OCTET STRING (SIZE  (1..1024))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "Comma separated list of the Unique Event identifiers

        that led to the generation of this Alarm." 

    ::= { cenAlarmEntry 20 }


cenUserMessage1 OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..255))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "User input message. This value can be configured." 

    ::= { cenAlarmEntry 21 }


cenUserMessage2 OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..255))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "User input message. This value can be configured." 

    ::= { cenAlarmEntry 22 }


cenUserMessage3 OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..255))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "User input message. This value can be configured." 

    ::= { cenAlarmEntry 23 }


cenAlarmMode OBJECT-TYPE

    SYNTAX          INTEGER  {

                        unknown(1),

                        alert(2),

                        event(3)

                    }

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "unknown:  When the value for this attribute could not be

        determined.       

        alert:    Denotes an alarm generated by a set of events where 

        all events are reported by polling of managed 

        objects and/or listening to SNMP notifications.

        event:    Denotes an event generated by polling of managed 

        ojects and/or listening to SNMP notifications." 

    ::= { cenAlarmEntry 24 }


cenPartitionNumber OBJECT-TYPE

    SYNTAX          Unsigned32 (0..100)

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "In traps generated by the management application that support

        multiple partitions, the attribute will carry the integer 

        value assigned to identify the logical group where the managed 

        device resides." 

    ::= { cenAlarmEntry 25 }


cenPartitionName OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..255))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "In traps generated by the management application that support

        multiple partitions, the attribute will carry the name 

        assigned to identify the logical group where the managed

        device resides." 

    ::= { cenAlarmEntry 26 }


cenCustomerIdentification OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..255))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "User input message. The attribute takes in a free format

        text. This attribute can be used by advanced management 

        applications to sort responses from the fault management 

        server." 

    ::= { cenAlarmEntry 27 }


cenCustomerRevision OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..255))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "User input message. The attribute takes in a free format

        text. This attribute can be used by advanced management 

        applications to sort responses from the fault management 

        server." 

    ::= { cenAlarmEntry 28 }


cenAlertID OBJECT-TYPE

    SYNTAX          SnmpAdminString (SIZE  (1..20))

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "In event based notification, this attribute will contain the

        alert id to which the generated event has been rolled up

        to. In alert based notification, the cenAlarmInstanceId and 

        cenAlertID would be identical." 

    ::= { cenAlarmEntry 29 }


cenAlarmObjectId OBJECT-TYPE

    SYNTAX          OBJECT IDENTIFIER

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "This object represents the identifier of the Object that has

        exceeded the configured value. 


        The OIDs populated through this object would represent one 

        of the following kind of Objects. 


        1) Existing MIB objects that represent a particular statistic


        like ifInOctets ( RFC1213-MIB ).  The OID of the respective 

        object will be populated. 


        2) New Objects that are derived out of already-existing

        objects.


        Eg: 'TxUtilization' which is computation of 'ifOutOctets' and

        'ifSpeed'. For this kind of variables the OID values are

        mentioned in this MIB under the subtree

        ciscoEpmNotificationMIBObjects.ciscoEpmNotificationComputedVar." 

    ::= { cenAlarmEntry 30 }


cenAlarmObjectInstance OBJECT-TYPE

    SYNTAX          RowPointer

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "This object identifies the instance of the OID populated

        through cenAlarmObjectId." 

    ::= { cenAlarmEntry 31 }


cenAlarmViolatedValue OBJECT-TYPE

    SYNTAX          Unsigned64

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "This object represents the value of the objectId represented

        in cenAlarmObjectId when it exceeded the rule represented

        with cenAlarmDescription." 

    ::= { cenAlarmEntry 32 }


cenAlarmViolatedValueMantissa OBJECT-TYPE

    SYNTAX          Integer32 (0..99)

    MAX-ACCESS      read-only

    STATUS          current

    DESCRIPTION

        "This represents the mantissa part of the violated value. As

        cenAlarmViolatedValue cannot accommodate floating point

        value, this part required to be mentioned separately. This will

        represent the values up to 1/100th of the decimal part." 

    ::= { cenAlarmEntry 33 }


cencIfRxUtilization OBJECT-IDENTITY

    STATUS          current

    DESCRIPTION

        "This object represents the incoming data utilization of a low

        speed interface(which is < 20mbps).


        This is calculated as below


        RxUtilization of an interface


        RxUtilization = (ifInOctets*8*100)/ifSpeed"

    ::= { ciscoEpmNotificationComputedVar 1 }



cencIfTxUtilization OBJECT-IDENTITY

    STATUS          current

    DESCRIPTION

        "This object represents the outgoing data utilization of a low

        speed interface(which is < 20mbps).


        This is calculated as below


        TxUtilization of an interface


        TxUtilization = (ifOutOctets*8*100)/ifSpeed"

    ::= { ciscoEpmNotificationComputedVar 2 }



cencMemoryUtilization OBJECT-IDENTITY

    STATUS          current

    DESCRIPTION

        "This object represents the memory utilization of different

        instances(modules) on a managed object as represented in

        CISCO-MEMORY-POOL-MIB.


        Memory utilization of the managed object


        Memory Utilization =

        (ciscoMemoryPoolUsed/(ciscoMemoryPoolUsed+ciscoMemoryPoolFree))*


        100"

    ::= { ciscoEpmNotificationComputedVar 3 }



cencHrStorageUtilization OBJECT-IDENTITY

    STATUS          current

    DESCRIPTION

        "This object represents the memory utilization of different

        instances(modules) on a managed object as represented in

        HOST-RESOURCES-MIB.


        hrStorageUtilization = (hrStorageUsed/hrStorageSize)*100"

    ::= { ciscoEpmNotificationComputedVar 4 }



cenc64bitIfRxUtilization OBJECT-IDENTITY

    STATUS          current

    DESCRIPTION

        "This object represents the incoming data utilization of a high

        capacity interface(which is > 20mbps).


        This is calculated as below


        64bitRxUtilization = (ifHcInOctets*8*100)/(ifHighSpeed*1000000)"

    ::= { ciscoEpmNotificationComputedVar 5 }



cenc64bitIfTxUtilization OBJECT-IDENTITY

    STATUS          current

    DESCRIPTION

        "This object represents the outgoing data utilization of a high

        capacity interface(which is > 20mbps).


        This is calculated as below


        64bitTxUtilization =

        (ifHcOutOctets*8*100)/(ifHighSpeed*1000000)"

    ::= { ciscoEpmNotificationComputedVar 6 }



cencPowerUtilization OBJECT-IDENTITY

    STATUS          current

    DESCRIPTION

        "This object represents the power utilization of Power over

        Ethernet enabled interfaces.


        Power Utilization =

        (pethMainPseConsumptionPower/pethMainPsePower)*100"

    ::= { ciscoEpmNotificationComputedVar 7 }



ciscoEpmNotificationAlarm NOTIFICATION-TYPE

    OBJECTS         {

                        cenAlarmVersion,

                        cenAlarmTimestamp,

                        cenAlarmUpdatedTimestamp,

                        cenAlarmInstanceID,

                        cenAlarmStatus,

                        cenAlarmStatusDefinition,

                        cenAlarmType,

                        cenAlarmCategory,

                        cenAlarmCategoryDefinition,

                        cenAlarmServerAddressType,

                        cenAlarmServerAddress,

                        cenAlarmManagedObjectClass,

                        cenAlarmManagedObjectAddressType,

                        cenAlarmManagedObjectAddress,

                        cenAlarmDescription,

                        cenAlarmSeverity,

                        cenAlarmSeverityDefinition,

                        cenAlarmTriageValue,

                        cenEventIDList,

                        cenUserMessage1,

                        cenUserMessage2,

                        cenUserMessage3

                    }

    STATUS          deprecated

    DESCRIPTION

        "Notification of the status of the managed object as

        generated by the  management server. 


        New attributes are added to the ciscoEpmNotificationAlarmRev1.

        Hence this notification is deprecated."

   ::= { ciscoEpmNotificationMIBNotifs 1 }


ciscoEpmNotificationAlarmRev1 NOTIFICATION-TYPE

    OBJECTS         {

                        cenAlarmVersion,

                        cenAlarmTimestamp,

                        cenAlarmUpdatedTimestamp,

                        cenAlarmInstanceID,

                        cenAlarmStatus,

                        cenAlarmStatusDefinition,

                        cenAlarmType,

                        cenAlarmCategory,

                        cenAlarmCategoryDefinition,

                        cenAlarmServerAddressType,

                        cenAlarmServerAddress,

                        cenAlarmManagedObjectClass,

                        cenAlarmManagedObjectAddressType,

                        cenAlarmManagedObjectAddress,

                        cenAlarmDescription,

                        cenAlarmSeverity,

                        cenAlarmSeverityDefinition,

                        cenAlarmTriageValue,

                        cenEventIDList,

                        cenUserMessage1,

                        cenUserMessage2,

                        cenUserMessage3,

                        cenAlarmMode,

                        cenPartitionNumber,

                        cenPartitionName,

                        cenCustomerIdentification,

                        cenCustomerRevision,

                        cenAlertID

                    }

    STATUS          current

    DESCRIPTION

        "Notification of the status of the managed object as

        generated by the  management server."

   ::= { ciscoEpmNotificationMIBNotifs 2 }


ciscoEpmHealthNotificationAlarm NOTIFICATION-TYPE

    OBJECTS         {

                        cenAlarmObjectId,

                        cenAlarmObjectInstance,

                        cenAlarmViolatedValue,

                        cenAlarmViolatedValueMantissa,

                        cenAlarmTimestamp,

                        cenAlarmCategory,

                        cenAlarmCategoryDefinition,

                        cenAlarmManagedObjectAddressType,

                        cenAlarmManagedObjectAddress,

                        cenAlarmDescription,

                        cenAlarmSeverity,

                        cenUserMessage1,

                        cenAlarmSeverityDefinition

                    }

    STATUS          current

    DESCRIPTION

        "Notification of details of the violation configured for mib

        variables that are monitored by management server."

   ::= { ciscoEpmNotificationMIBNotifs 3 }

-- Conformance information


ciscoEpmNotificationMIBCompliances  OBJECT IDENTIFIER

    ::= { ciscoEpmNotificationMIBConform 1 }


ciscoEpmNotificationMIBGroups  OBJECT IDENTIFIER

    ::= { ciscoEpmNotificationMIBConform 2 }



-- Compliance


ciscoEpmNotificationMIBCompliance MODULE-COMPLIANCE

    STATUS          deprecated

    DESCRIPTION

        "The compliance statement for entities which

        implement the CISCO-EPM-NOTIFICATION-MIB. 



        New attributes are included in

        ciscoEpmNotificationMIBComplianceRev1. Hence this object is

        deprecated."

    MODULE          -- this module

    MANDATORY-GROUPS {

                        ciscoEpmNotificationObjectsGroup,

                        ciscoEpmNotificationAlarmGroup

                    }


    GROUP           ciscoEpmAlarmConfigGroup

    DESCRIPTION

        "This group is optional."


    OBJECT          cenAlarmTableMaxLength

    MIN-ACCESS      read-only

    DESCRIPTION

        "Write access is not required."


    OBJECT          cenAlarmVersion

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmTimestamp

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmUpdatedTimestamp

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmInstanceID

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmStatus

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmStatusDefinition

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmType

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmCategory

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmCategoryDefinition

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmServerAddressType

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmServerAddress

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmManagedObjectClass

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmManagedObjectAddressType

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmManagedObjectAddress

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmDescription

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmSeverity

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmSeverityDefinition

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmTriageValue

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenEventIDList

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenUserMessage1

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenUserMessage2

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenUserMessage3

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."

    ::= { ciscoEpmNotificationMIBCompliances 1 }


ciscoEpmNotificationMIBComplianceRev1 MODULE-COMPLIANCE

    STATUS          current

    DESCRIPTION

        "The compliance statement for entities which

        implement the CISCO-EPM-NOTIFICATION-MIB."

    MODULE          -- this module

    MANDATORY-GROUPS {

                        ciscoEpmNotificationObjectsGroupRev1,

                        ciscoEpmNotificationAlarmGroupRev1

                    }


    GROUP           ciscoEpmAlarmConfigGroup

    DESCRIPTION

        "This group is optional."


    OBJECT          cenAlarmTableMaxLength

    MIN-ACCESS      read-only

    DESCRIPTION

        "Write access is not required."


    OBJECT          cenAlarmVersion

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmTimestamp

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmUpdatedTimestamp

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmInstanceID

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmStatus

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmStatusDefinition

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmType

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmCategory

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmCategoryDefinition

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmServerAddressType

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmServerAddress

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmManagedObjectClass

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmManagedObjectAddressType

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmManagedObjectAddress

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmDescription

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmSeverity

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmSeverityDefinition

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmTriageValue

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenEventIDList

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenUserMessage1

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenUserMessage2

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenUserMessage3

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlarmMode

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenPartitionNumber

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenPartitionName

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenCustomerIdentification

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenCustomerRevision

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."


    OBJECT          cenAlertID

    MIN-ACCESS      accessible-for-notify

    DESCRIPTION

        "Read access is not required."

    ::= { ciscoEpmNotificationMIBCompliance 2 }


-- Units of Conformance


ciscoEpmNotificationAlarmGroup NOTIFICATION-GROUP

   NOTIFICATIONS    { ciscoEpmNotificationAlarm }

    STATUS          deprecated

    DESCRIPTION

        "The collection of notifications used to indicate managed

        object status. 


        ciscoEpmNotificationAlarmGroupRev1 is defined. Hence this 

        object is deprecated."

    ::= { ciscoEpmNotificationMIBGroups 1 }


ciscoEpmNotificationObjectsGroup OBJECT-GROUP

    OBJECTS         {

                        cenAlarmVersion,

                        cenAlarmTimestamp,

                        cenAlarmUpdatedTimestamp,

                        cenAlarmInstanceID,

                        cenAlarmStatus,

                        cenAlarmStatusDefinition,

                        cenAlarmType,

                        cenAlarmCategory,

                        cenAlarmCategoryDefinition,

                        cenAlarmServerAddressType,

                        cenAlarmServerAddress,

                        cenAlarmManagedObjectClass,

                        cenAlarmManagedObjectAddressType,

                        cenAlarmManagedObjectAddress,

                        cenAlarmDescription,

                        cenAlarmSeverity,

                        cenAlarmSeverityDefinition,

                        cenAlarmTriageValue,

                        cenEventIDList,

                        cenUserMessage1,

                        cenUserMessage2,

                        cenUserMessage3

                    }

    STATUS          deprecated

    DESCRIPTION

        "Trap reflecting the alarm.


        New attributes are added to the new notification 

        ciscoEpmNotificationObjectsGroupRev1. Hence

        this object is deprecated."

    ::= { ciscoEpmNotificationMIBGroups 2 }


ciscoEpmAlarmConfigGroup OBJECT-GROUP

    OBJECTS         { cenAlarmTableMaxLength }

    STATUS          current

    DESCRIPTION

        "A collection of objects providing information

        about the total number of cenAlarmTable entries

        maintained."

    ::= { ciscoEpmNotificationMIBGroups 3 }


ciscoEpmNotificationAlarmGroupRev1 NOTIFICATION-GROUP

   NOTIFICATIONS    {

                        ciscoEpmNotificationAlarmRev1,

                        ciscoEpmHealthNotificationAlarm

                    }

    STATUS          current

    DESCRIPTION

        "The collection of notifications used to indicate managed object

        status."

    ::= { ciscoEpmNotificationMIBGroups 4 }


ciscoEpmNotificationObjectsGroupRev1 OBJECT-GROUP

    OBJECTS         {

                        cenAlarmVersion,

                        cenAlarmTimestamp,

                        cenAlarmUpdatedTimestamp,

                        cenAlarmInstanceID,

                        cenAlarmStatus,

                        cenAlarmStatusDefinition,

                        cenAlarmType,

                        cenAlarmCategory,

                        cenAlarmCategoryDefinition,

                        cenAlarmServerAddressType,

                        cenAlarmServerAddress,

                        cenAlarmManagedObjectClass,

                        cenAlarmManagedObjectAddressType,

                        cenAlarmManagedObjectAddress,

                        cenAlarmDescription,

                        cenAlarmSeverity,

                        cenAlarmSeverityDefinition,

                        cenAlarmTriageValue,

                        cenEventIDList,

                        cenUserMessage1,

                        cenUserMessage2,

                        cenUserMessage3,

                        cenAlarmMode,

                        cenPartitionNumber,

                        cenPartitionName,

                        cenCustomerIdentification,

                        cenCustomerRevision,

                        cenAlertID,

                        cenAlarmObjectId,

                        cenAlarmObjectInstance,

                        cenAlarmViolatedValue,

                        cenAlarmViolatedValueMantissa

                    }

    STATUS          current

    DESCRIPTION

        "Notification reflecting the alarm."

    ::= { ciscoEpmNotificationMIBGroups 5 }


END

cenAlarmEntry Object-Type—Definitions for Selected Attributes

Table C-1 explains the values for attributes related to alert status, category, and severity. You might find it useful to consult this information when you look at a generated trap.

Table C-1 CenAlarmEntry—Alert Status, Category, and Severity 

Sequence Numbers
Attributes
Values

(6)

(7)

cenAlarmStatus

cenAlarmStatusDefinition

Number—From 1 to 3.

String—Includes number (cenAlarmStatus) and description:

1-ACK

2-Active

3-Cleared

Alert status changes from state to state: state is Active; if user acknowledges alert, state is ACK; ultimately, state is Cleared.

For more information about alerts, see Using the Alerts and Activities Display

(9)

(10)

cenAlarmCategory

cenAlarmCategoryDefinition

Number—From 0 to 9.

String—Includes number (cenAlarmCategory) and description:

0-Unknown

1-Application

2-Environment

3-Interface

4-Reachability

5-Connectivity

6-Utilization

7-System Hardware

8-Security

9-Other

(17)

(18)

cenAlarmSeverity

cenAlarmSeverityDefinition

Number—From 1 to 3.

String—Includes number (cenAlarmSeverity) and description:

1-Informational

2-Critical