Table Of Contents
Diagnosing Problems With CiscoWorks Server
Verifying Server Status
Testing Device Connectivity
Troubleshooting the CiscoWorks Server
Frequently Asked Questions
Troubleshooting Suggestions
Diagnosing Problems With CiscoWorks Server
Use these tools and suggestions to diagnose problems with the CiscoWorks server:
•
Verifying Server Status
•Testing Device Connectivity
•Troubleshooting the CiscoWorks Server
•Troubleshooting Suggestions
Verifying Server Status
There are several tools that enable you to gather and analyze information about your CiscoWorks Server. See Table 8-1 and Table 8-2.
Table 8-1 Server Status
Task
|
Purpose
|
Action
|
Administrative Tasks
|
Perform self test.
|
Runs self-tests and generates a report with the results.
|
Select Server > Admin > Self Test.
|
All Users
|
Check process status.
|
Checks whether back-end processes are in an interim state.
|
Select
Server > Admin > Processes.
|
Collect server information.
|
Provides system information, environment, configuration, logs, and web server information.
|
Select
Server > Admin > Collect Server Information
or
Enter the following command:
•On Windows:
NMSROOT\bin\collect.info
•On Solaris:
$NMSROOT/bin/collect.info
where NMSROOT and $NMSROOT are the directories where you installed CiscoWorks, in Windows and Solaris respectively.
|
MDC Support
|
The MDC Support utility collects log files, configuration settings, memory info, complete system related info, process status and host environment information.
It also collects any other relevant data, into a deliverable tar (compressed form) file to support the MDCs installed.
The MDC Support utility also queries CCR for any other support utilities registered, and run them.
Other MDCs need to register their own support utilities that will collect their relevant data.
|
For Windows go to,
NMSROOT\MDC\bin and run the command:
MDCSupport.exe
The utility creates a tar file in NMSROOT\MDC\etc directory.
If \etc directory is full, or if you want to preserve the data collected previously by not over writing the tar file, you may create another directory by running the following command:
MDCSupport.exe Directory
For Solaris,
/opt/CSCOpx/MDC/bin and run the command:
./mdcsupport
The utility creates a tar file in CSCOpx/MDC/etc directory.
|
MDCSupport (Continued)
|
|
If \etc directory is full, or if you want to preserve the data collected previously by not over writing the tar file, you may create another directory by running the following command:
./mdcsupport Directory
Before you close the command window, ensure that the MDC Support utility has completed its action.
If you close the window prematurely, the subsequent instances of MDCSupport Utility will not function properly.
If you happen to close the window, delete the mdcsupporttemp directory from NMSROOT\MDC\etc directory, for subsequent instances to work properly.
|
Testing Device Connectivity
The connectivity tools enable you to test device connectivity and reachability and troubleshoot nonresponsive devices. Some connectivity tools require system administrative-level privileges (see Connectivity Tools Tasks Table 8-2).
Table 8-2 Connectivity Tools Tasks
Task
|
Purpose
|
Action
|
Traceroute.
|
Detects routing errors between the network management station and a target device.
|
Select
Device Center > Tools > Traceroute.
See "Using Traceroute" section, for details.
|
Ping a device.
|
Tests device reachability using an ICMP echo message and its reply.
|
Select
Device Center > Tools > Ping
See "Using Ping" section, for details.
|
Check Management Station to Device
|
Checks the connectivity between the CiscoWorks Server and a device.
|
Select
Device Center > Tools > Management Station to Device
See "Checking Device Connectivity" section, for details.
|
Packet Capture.
|
Captures live data from the CiscoWorks machine to aid in troubleshooting.
|
Select
Device Center > Tools > Packet Capture
See "Using Packet Capture" section, for details.
|
To set an SNMP object on a device.
|
Sets an SNMP object on a device for purposes of controlling the device.
|
Select
Device Center > Tools > SNMP Set
See "Using SNMP Set" section, for details.
|
To walk the MIB tree of a device.
|
Walks the MIB tree of a device starting from a given OID for troubleshooting, or gathering information about a device.
|
Select
Device Center > Tools > SNMP Walk
See "Using SNMP Walk" section, for details.
|
Troubleshooting the CiscoWorks Server
This section provides information on frequently asked questions (FAQs) and suggestions for troubleshooting the CiscoWorks Server components.
If the suggestions do not resolve the error, check the Release Notes supporting your platform for possible workarounds, or contact the Cisco TAC or your customer support.
Frequently Asked Questions
•When I connect to the CiscoWorks Server in the secure mode (HTTPS) using Netscape Navigator, the browser returns I/O errors and displays the message Netscape has encountered bad data from the server. Why does this happen?
•When I invoke CiscoWorks in the secure mode (HTTPS), there are too many dialog boxes. This makes the process tedious. Is there a way to reduce the number of dialog boxes and steps?
•When I invoke CiscoWorks, I'm unable to get to the login page directly. Instead, I'm facing a security alert related to the site's security certificate. It asks for my input to proceed further. Why?
•My server certificate for CiscoWorks has expired. What should I do?
•I installed CD One and got an error message that EDS was not registered with the daemon manager. Did I do anything wrong?
•Which version of the Java Plug-in should I use for CiscoWorks to function properly?
•Is there anything I should do before I invoke Netscape Navigator sessions in UNIX systems to run CiscoWorks?
•Why do some CiscoWorks applications not appear in the product?
•Why can't I start my CiscoWorks application?
•What kind of directory structure does CiscoWorks use when backing up data?
•I'm locked out of the CiscoWorks Server. Why did this happen, and how do I regain access?
•What if the database is inaccessible?
•How do I change the port for osagent in Windows?
•How do I change port for osagent in Solaris?
•How do I change the ESS port in Solaris?
•How do I change ESS port in Windows?
•I have configured the Active Directory Login Module but it does not work. How can I analyze the problem?
•How do I change the IP Address of the CiscoWorks Server after installing it, or after running it for a while?
•Do I need to change the CiscoWorks configuration after changing the IP address?
•How do I change the Hostname of the CiscoWorks Server after installing it, or after running it for a while?
•How do I find out which devices are supported by a particular application?
•How do I verify if SSH is enabled or disabled on my device using CiscoWorks Server?
•How do I verify if SSH is enabled or disabled on my device using CiscoWorks Server?
•How to verify which version of SSH is running on my system?
•Is it possible to have both CiscoWorks and ACS on the same machine?
•How do I change the casuser password?
•How do I change the CiscoWorks user password?
•How do I enable/disable ACS Communication on HTTPS from CLI?
•How do I change web server port numbers?
•Ho do I increase Tomcat heap size?
•How do I enable debugging in MICE?
•What does cmf stand for?
Q. When I connect to the CiscoWorks Server in the secure mode (HTTPS) using Netscape Navigator, the browser returns I/O errors and displays the message Netscape has encountered bad data from the server. Why does this happen?
A. This problem occurs when you:
•Create a new server certificate using the same hostname
•Set the browser to accept the old server certificate, till it expires
Typically, this problem is fixed when you clear the entry for your old server certificate from the browser.
Note The I/O errors in Netscape Navigator running in secure mode (HTTPS) is often caused by configured certificates in the client computer.
Q. When I invoke CiscoWorks in the secure mode (HTTPS), there are too many dialog boxes. This makes the process tedious. Is there a way to reduce the number of dialog boxes and steps?
A. Yes. You have the following options:
•If you are using self-signed certificates:
–In Netscape Navigator, select the option Accept the Server Certificate forever (until it expires) in the New Site Certificate wizard, if you are confident about the identity of the server.
–In Internet Explorer, install the certificate in the browser's trusted certificate stores, if you are confident about the identity of the server.
•Use a server certificate issued by a prominent third party certificate authority (CA).
•Configure the hostname in your server certificate properly, and use the same hostname to invoke CiscoWorks.
Q. When I invoke CiscoWorks, I'm unable to get to the login page directly. Instead, I'm facing a security alert related to the site's security certificate. It asks for my input to proceed further. Why?
A. CiscoWorks does not have any control over this behavior. This is an expected browser behavior (Microsoft Internet Explorer or Netscape Navigator), to ensure proper security.
This appears if one of the when one of the following conditions is not satisfied:
–The certificate of the server (CiscoWorks Server in this case) must be issued by trusted Certificate Authority.
–The date of the certificate must be valid. (Each certificate is assigned a validity period. It can range from 21 days to 5 years).
–The name of the certificate and name of the page (or the name typed in the address bar of the browser) are the same.
To view the certificate information:
•Click View Certificate, in the alert box for Internet Explorer.
•Click Examine Certificate in the alert box for Netscape Navigator.
The server should be invoked with the name same as the Issued to' field of the certificate.
To install the certificate in Internet Explorer:
Step 1 Click View Certificate in the alert box.
The Certificate dialog box displays the Certificate information.
Step 2 Click Install Certificate.
For Netscape Navigator, you may select the Accept this Certificate Permanently radio button in the security alert dialog box.
Q. My server certificate for CiscoWorks has expired. What should I do?
A. If you are using a self-signed certificate, you can create a new certificate using the Create Self Signed Certificate option. For more information, see "Creating Self Signed Certificate" section.
If you are using a third party issued certificate, you must contact the certificate authority (CA) and renew the certificate. You can use a self-signed certificate till you get the certificate renewed by the CA.
Note Before you perform any certificate management operations—creating or modifying certificates, back up the certificate files, the server private key in particular, and keep them in a safe location.
Q. I installed CD One and got an error message that EDS was not registered with the daemon manager. Did I do anything wrong?
A. EDS is part of the CD One deliverable but is not enabled without Campus Manager or Resource Manager Essentials. If you are going to install either of these application suites, EDS will be automatically enabled after installation.
Q. Which version of the Java Plug-in should I use for CiscoWorks to function properly?
A. CiscoWorks supports Java Plug-in 1.4.2_04 only in all the supported clients and operating systems. We recommend that you do not install any other Plug-ins other than this one, for CiscoWorks to function properly.
Q. Is there anything I should do before I invoke Netscape Navigator sessions in UNIX systems to run CiscoWorks?
A. Yes. You must source the file /jpi.cshrc before invoking any Netscape session in UNIX systems, so that the environment is set for the browser to function properly on invoking CiscoWorks.
Q. Why do some CiscoWorks applications not appear in the product?
A. The CiscoWorks Server represents a common set of management services which are shared by multiple network management applications. These services are enabled when a suite is installed and an application that relies on a particular service enables it.
If a particular suite of applications does not use a particular service, the service might not appear on the CiscoWorks Homepage. Applications and application suites may not use these features at all, or to the fullest extent.
See the User Guide for your application suite to determine the extent to which these features are used.
Q. Why can't I start my CiscoWorks application?
A. If you cannot start your CiscoWorks application and get error messages complaining that the WebServer might not be running. This may occur although pdshow indicates that those processes are up and running. You might need to check how your machine is resolving its server name and IP address.
The CiscoWorks CORBA applications require name resolution to work properly. Domain Name Service (DNS) is a must for CiscoWorks CORBA applications to work properly.
Configure the name resolution mechanism and restart the CiscoWorks Server to access the application correctly.
Q. What kind of directory structure does CiscoWorks use when backing up data?
A. CiscoWorks uses a standard database structure for backing up all suites and applications. See Table 8-3 for sample directory structure for the CiscoWorks Server.
Table 8-3 Sample Backup Directory
Directory Path
|
Description
|
Usage Notes
|
/tmp/1
|
Number of backups
|
1, 2, 3...
|
/tmp/2/cmf
|
Application or suite
|
Backs up CiscoWorks Server applications.
|
/tmp/1/cmf/filebackup.tar
|
CiscoWorks Server application tar files
|
Application data is stored in the datafiles.txt which are compiled into the tar file.
|
/tmp/1/cmf/database
|
CiscoWorks Server database directory
|
Includes files for each database:
xxx_DbVersion.txt
xxx.db database files
xxx.log database log files
xxx.txt database backup manifest file
|
Q. I'm locked out of the CiscoWorks Server. Why did this happen, and how do I regain access?
A. There are several reasons why you might have been locked out. Most likely it is due to the changes made using the Select Login Module option. You must replace the incorrect login module with a default configuration, log into CiscoWorks, and return to the login module to correct one or more of the following:
•Session Time out
•Change from SSL mode to non-SSL mode
•Change from non-SSL mode to SSL mode
•Log out from any other CiscoWorks application
•Visit other sites and then return to CiscoWorks
Do not alter the existing technologies in the default configuration file.
If all of the parameters listed are correct, see the "Troubleshooting Suggestions" section.
Q. What if the database is inaccessible?
A. If the server is not able to connect to the database, the database might be corrupt or inaccessible. This can occur if processes are not running. Try the following:
Step 1 Log in to CiscoWorks as admin.
Step 2 Select Server > Admin > Process to get a list of CiscoWorks back-end processes that have failed.
Step 3 Select Server > Admin > Self Test.
•Click Create to create a report.
•Click Display to display the report.
Step 4 Select Server > Admin > Collect Server Information.
Step 5 Click the Product Database Status link to get detailed database status.
Step 6 Contact the Cisco TAC or your customer support to get the information you need to access the database and find out details about the problem. After you have the required information, perform the following tasks for detecting and fixing database errors.
Depending upon the degree of corruption, the database engine may or may not start. For certain corruptions, such as bad indexes, the database can function normally until the corrupt index is accessed.
Database corruptions, such as index corruptions, can be detected by the dbvalid utility, which requires the database engine to be running.
To detect database corruption:
Step 1 Log on as root (UNIX) or with administrator privileges (Windows).
Step 2 Stop the Daemon manager if it is already running:
•UNIX—/etc/init.d/dmgtd stop
•Windows—net stop crmdmgtd (enter this command in an MS-DOS window)
Step 3 Make sure no database processes are running and there is no database log file. For example, if the database file is /opt/CSCOpx/databases/rme/rme.db, the database log file is /opt/CSCOpx/databases/rme/rme.log. This file is not present if the database process shuts down cleanly.
Step 4 (UNIX only) Check if the database files(s) and the transaction log file (*.log) are owned by user casuser. If not, change the ownership of these files to user casuser and group casusers.
Step 5 Run the command:
cd NMSROOT/objects/db/conf
NMSROOT/bin/perl configureDb.pl action=validate dsn=<cmf>
The dbvalid command displays a list of tables being validated. The Validation utility scans the entire table, and looks up each record in every index and key defined on the table. If there are errors, the utility displays something like:
run time SQL error -- Foreign key parent_is has invalid or duplicate
index
If the above command reports any error, you may try:
•Restoring from a previous good backup
or
•Reinitializing database
Caution All the current data will be lost.
To do this, you have to run the following command:
NMSROOT\bin\perl NMSROOT\bin\dbRestoreOrig.pl dsn=dsn
dmprefix=dmprefix
For Common Services, dsn is cmf and dmprefix is Cmf.
Q. How do I ensure that jrm is running fine?
A. To check whether jrm is working on Windows, at the command prompt enter:
cwjava -cw NMSROOT com.cisco.nm.cmf.jrm.jobcli
To check whether jrm is working on Solaris, at the command prompt enter
cwjava -cw $NMSROOT com.cisco.nm.cmf.jrm.jobcli
•If you get a message Established connection with JRM, then EDS, EDS-GCF and jrm are running.
•If you do not get the above message, contact the technical assistance center with the error message.
•If your jrm in down or inaccessible, you'll get a message while accessing the UIs.
Q. How do I change the port for osagent in Windows?
A. To change the port for osagent in Windows:
Step 1 Backup your Windows registry.
Step 2 In the Registry Editor, navigate to HKEY_LOCAL_MACHINE > SOFTWARE > Cisco > Resource Manager > Current Version > Daemon > RmeOrb
Step 3 Change the value of Args from -p 42342 to an unused port number, for example -p 44444.
Step 4 Navigate to HKEY_LOCAL_MACHINE > SOFTWARE > Cisco > Resource Manager > Current Version > Daemon > RmeGatekeeper
Step 5 Change the value of Args from
-DNMSROOT=NMSROOT -DORBagentPort=42342 com.visigenic.vbroker.gatekeeper.GateKeeper -props NMSROOT\lib\visigenics\gatekeeper.cfg
to
-DNMSROOT=NMSROOT -DORBagentPort=44444 com.visigenic.vbroker.gatekeeper.GateKeeper -props NMSROOT\lib\visigenics\gatekeeper.cfg
Step 6 Navigate to HKEY_LOCAL_MACHINE > SOFTWARE > Cisco > Resource Manager > Current Version > Environment:
Step 7 Change the value of OSAGENT_PORT and PX_OSA_PORT from 42342 to 44444.
Step 8 Open the file NMSROOT\lib\classpath\md.properties, in any plain text editor, such as Notepad.
Step 9 Change the value of OSAGENT_PORT and PX_OSA_PORT from 42342 to 44444.
Step 10 Reboot the server.
NMSROOT is the installation directory for CiscoWorks Server.
Q. How do I change port for osagent in Solaris?
A. To do this:
Step 1 Stop daemons.
Step 2 Make sure that no CSCO processes are running.
Step 3 Make sure all ports used by CiscoWorks are free.
To do this, enter:
If these ports are free, you will not see any output.
Step 4 Verify whether the port 44444 is free, using the following command:
If the port is free, you will not see any output.
Step 5 Back up $NMSROOT/objects/dmgt/dmgtd.conf file.
Step 6 Edit the file dmgtd.conf using a text editor.
a. Change the line:
RmeOrb y - $NMSROOT/lib/vbroker/bin/osagent -p 42342 to RmeOrb y - $NMSROOT/lib/vbroker/bin/osagent -p 44444
b. Change the port number for RmeGatekeeper from:
RmeGatekeeper y RmeOrb $NMSROOT/lib/vbroker/bin/rungk.sh 42342
to
RmeGatekeeper y RmeOrb $NMSROOT/lib/vbroker/bin/rungk.sh 44444
Step 7 Open the file /etc/services in a plain text editor such as vi.
Step 8 Comment out the entry for CSCOsa port and add the following entry:
cscoosa 44444/udp # CSCO NM osagent
Note The change is for the port number only.
Step 9 Open /var/sadm/pkg/CSCOmd/pkginfo in a plain text editor, such as vi.
•Change the entry from
OSAGENT_PORT= 42342
to
OSAGENT_PORT=44444
•Change the entry from
PX_OSA_PORT=42342
to
PX_OSA_PORT=44444
Step 10 Restart the daemons. We recommend that you also reboot the server.
Q. How do I change the ESS port in Solaris?
A. There are 4 ports related to ESS:
•ESS Service Port: 42350/udp
•ESS listening port: 42351/tcp
•ESS HTTP Port: 42352/tcp
•ESS Routing Port: 42353/tcp
The ports mentioned above are default ports. The alternative ports defined for these in CiscoWorks are 44350, 44351, 44352, 44353 respectively.
To change the ports:
Step 1 Open the file $NMSROOT/objects/ess/conf/essproperties.conf in a plain text editor, such as vi.
Step 2 Change the port numbers as required.
Step 3 Reboot the system.
Q. How do I change ESS port in Windows?
A. To do this:
Step 1 Back up your Windows registry.
Step 2 In the Registry Editor, navigate to HKEY_LOCAL_MACHINE >SOFTWARE > Cisco > Resource Manager > Current Version > Daemon > ESS
Step 3 Change the value of Args from
-store NMSROOT\objects\ess\conf\rvrd.conf -logfile NMSROOT\log\ess.log -listen 42351 -no-http
to
-store NMSROOT\objects\ess\conf\rvrd.conf -logfile NMSROOT\log\ess.log -listen 42351 -no-http
Step 4 Change the corresponding entry in NMSROOT\objects\ess\conf\essproperties.conf.
Step 5 Reboot the server.
Q. I have configured the Active Directory Login Module but it does not work. How can I analyze the problem?
A. To analyze the problem, enable the Debug mode for the Active Directory Login module. To do this:
Step 1 Login as Admin.
Step 2 Go to Server > Security > AAA Mode Setup.
The Select Login Module dialog box appears.
Step 3 Select a login module from the Available Login Modules list box and Click on Edit Options.
The Login Module Options dialog box appears.
Step 4 Select the radio button True and click on Finish.
This enables the Debug option. Enabling debug mode allows the login module to add the detailed progress and failure information to log files. The log files are located at:
CSCOpx/MDC/Tomcatlogs/stdout.log
For all failed login attempts, the log files contain LDAP error messages, which specify the reason for the failure.
For example, if the Usersroot configuration is incorrect, then the login module cannot match the complete DN string with any entries in the Active Directory database.
It indicates which portion of the DN matched and which portion did not match. You can verify your Active Directory setup and the entries for the Usersroot.
In some cases, the log file contains error messages with NameError. This indicates that either you entered a wrong user Id or there is some spelling error in the Usersroot configuration.
Q. How do I change the IP Address of the CiscoWorks Server after installing it, or after running it for a while?
A. You can change the IP address on the server, and then access it using the new IP address.
To change the IP address on Windows:
Step 1 Click Start > Settings > Network and Dial-up Connections > Local Area Connection.
The Local Area Connection Status dialog box appears.
Step 2 Click Properties.
The Local Area Connection Properties dialog box appears.
Step 3 Select Internet Protocol (TCP/IP) and click Properties.
The Internet Protocol (TCP/IP) Properties dialog box appears.
Step 4 Select the radio button Use the following IP address.
Step 5 Change the IP address as required, in the IP Address field.
For the subnet mask and default gateway values, use the command ipconfig at the command prompt.
The subnet mask and default gateway values appear.
Step 6 Enter these values in the subnet mask and default gateway fields.
Step 7 Click OK.
Step 8 Restart the server.
To change the IP address on Solaris, use the command ifconfig at the command prompt to change the IP address of the required interface.
For example, at the command prompt, you can enter:
ifconfig interfacename inet ipv4address
where the variable interfacename represents the name of the interface and ipv4address represents the new IP address.
Q. Do I need to change the CiscoWorks configuration after changing the IP address?
A. You do not need to change the CiscoWorks configuration whenever you change the IP address. CiscoWorks uses hostname for most of the communication. Only devices need to point to the new IP address. However, after changing the IP address, you must reboot the system on a Solaris server and restart the Daemon Manager on a Windows server. This is to make the changes effective.
Q. How do I change the Hostname of the CiscoWorks Server after installing it, or after running it for a while?
A. To change the hostname of the CiscoWorks Server, you need to update several files, and reboot the server:
Step 1 Change the hostname at My Computer > Properties > Network Identification > Properties.
Step 2 Change the hostname in all the following files:
Bundle
|
Solaris
|
Windows
|
LMS Bundle
|
•/etc/hosts.
Modify loghost to the new hostname.
•/etc/hostname.hm0 or the appropriate interface file.
Modify the file to the new hostname.
•/etc/nodename or the appropriate interface file.
Modify nodename to the new hostname.
Note These files may require server reboot.
•/opt/CSCOpx/lib/classpath/md.properties
Change "PX_HOST" to the new hostname.
•/var/sadm/pkg/CSCOmd/pkginfo
Change "PX_HOST" to the new hostname.
•Update new hostname in the DNS server.
|
•$NMSROOT\lib\classpath\md.properties file
•Update new hostname in the DNS server.
|
For Solaris, the sys-unconfig command erases the hostname and IP addresses pertaining to the Solaris system (not the LMS or SMS software) and guides you through the server-renaming process.
You can also do this when you change the hostname in the hosts, hostname.hme0, and nodename files in the /etc directory.
Step 3 Change the hostname in following registry entries:
•HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet.
•HKEY_LOCAL_MACHINE\SOFTWARE\Cisco\Resource Manager.
You must look for all the instances of hostname under these registry entries, and replace them with the new hostname.
Step 4 Change the hostname in regdaemon.xml ($NMSROOT/MDC/etc/regdaemon.xml)
Step 5 Change the hostname in web.xml ($NMSROOT/MDC/tomcat/webapps/classic/WEB-INF/web.xml)
Step 6 Create a file $NMSROOT/conf/cmic/changehostname.info, with the information on the updated hostname in the format:
OldhostName:NewhostName
OldhostName—Previous Hostname as registered with CCR(regdaemon.xml)
NewhostName—Current Hostname as registered with CCR(regdaemon.xml)
The entries for hostname in regdaemon.xml and changehostname.info should be identical.
Step 7 Delete gatekeeper.ior file:
Windows—NMSROOT\www\classpath
Solaris—/opt/CSCOpx/www/classpath
Step 8 Some of the devices added before you change the hostname may not be properly classified in Device Center. To rectify this, run the following commands:
For windows:
a. Enter net stop crmdmgtd to stop daemon manager.
b. Enter dbisqlc -c "uid=cmfDBA;pwd=dbpassword;eng=cmfEng;dbf=NMSROOT\databases\cmf\cmf.db" -q update PIDM_app_device_map SET app_hostname=`NewhostName' where app_hostname= `OldhostName'
For Solaris:
a. Enter /etc/init.d/dmgtd stop to stop daemon manager.
Enter setenv LD_LIBRARY_PATH $NMSROOT/objects/db/lib:$NMSROOT/lib
b. Enter dbisqlc -c "uid=cmfDBA;pwd=dbpassword;eng=cmfEng;dbf=NMSROOT/databases/cmf/cmf.db" -q update PIDM_app_device_map SET app_hostname=\`NewhostName\' where app_hostname=\`OldhostName\'
dbpassword is CiscoWorks Common Services Database password.
Step 9 Re-generate the Certificate. See Creating Self Signed Certificate for details. Enter the new hostname in the Hostname field.
Step 10 Reboot the Machine.
Note For RME on Solaris, you must change the hostname for CTMJrmServer daemon registration in the /opt/CSCOpx/objects/dmgt/dmgtd.conf file, before rebooting the CiscoWorks server.
See the Installation and Setup Guide for Resource Manager Essentials 4.0 on Solaris:
http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cw2000/
cw2000e/e_4_x/4_0/install/sol/trbls.htm
On changing the hostname, ensure that you:
•Redo the integration, if you have integrated any third party network management application to CiscoWorks, using Integration Utility.
•Reimport the Certificates and redo the Multi Server setup if the machine is part of a Multi Server setup.
For example, if you are changing the hostname of a machine that is configured as a Slave, then it needs to reregister with the Master. If you are changing the hostname of a machine that is configured as a Master, then all it's Slaves need to be updated with the new Master hostname.
•Add new hostname in ACS, if the AAA mode of the machine is set to ACS.
If the hostname of the machine changes, the stability of the system is not guaranteed and it fails in some cases.
See Release Notes for CiscoWorks Common Services for details.
Q. How do I find out which devices are supported by a particular application?
A. Select Common Services > Software Center > Software Updates Under Applications Installed, click the application name to see a list of the supported devices.
Q. How do I verify if SSH is enabled or disabled on my device using CiscoWorks Server?
A. To verify whether SSH is enabled or disabled using the CiscoWorks Server:
Step 1 Log on to the CiscoWorks.
Step 2 Select Common Services > Device Center >Tools > Management Station to Device.
Step 3 In the Check Connectivity dialog box, enter the device name and select the SSH check box.
If SSH enabled on the device, you will see:
If SSH is not enabled on the device, you will see:
Q. How to verify which version of SSH is running on my system?
A. You can verify the SSH version that is running on your system using the commands:
From the Command Line Interface, enter:
or
Q. Is it possible to have both CiscoWorks and ACS on the same machine?
A. No. This is because ACS mandates CiscoWorks to be configured as an AAA client in it for CiscoWorks to avail AAA service. At the same time, ACS does not allow itself to be configured as an AAA client, which is required when ACS and CiscoWorks coexists. Hence the configuration required for ACS integration will fail.
Q. How do I change the casuser password?
A. You can change the casuser password using resetCasuser.exe. It can be executed only by an administrator or casuser. To change the casuser password, do the following:
Step 1 At the command prompt, enter:
NMSROOT\setup\support resetCasuser.exe
You are provided with three options:
1. Randomly generate the password
2. Enter the password
3. Exit.
Step 2 Enter 2, and press Enter.
It prompts you to enter the password.
Step 3 Confirm the password.
Note You must know the password policy. If the password entered does not match the password policy, it exits.
Q. How do I change the CiscoWorks user password?
A. You can change the CiscoWorks user password using the CiscoWorks user password recovery utility.
To change the user password on Solaris:
Step 1 Enter /etc/init.d/dmgtd stop to stop the Daemon Manager.
At the command prompt, enter NMSROOT\bin resetpasswd username
Step 2 A message appears:
Enter new password for username:
Step 3 Enter the new password.
Step 4 Enter /etc/init.d/dmgtd start to start the Daemon Manager.
To change the user password on Windows:
Step 1 Enter net stop crmdmgtd to stop the Daemon Manager.
Step 2 At the command prompt, enter NMSROOT\bin resetpasswd <username>
Step 3 A message appears:
Enter new password for username:
Step 4 Enter the new password.
Enter net start crmdmgtd to start the Daemon Manager.
Q. How do I enable/disable ACS Communication on HTTPS from CLI?
A. To enable/disable ACS communication on HTTPS:
Step 1 Enter $NMSROOT/bin/perl $NMSROOT/bin/camssl.pl
The following message is displayed:
Usage:camssl.pl -enable | -disable
•To enable ACS communication on HTTPS:
Enter $NMSROOT/bin/perl $NMSROOT/bin/camssl.pl -enable
•To disable ACS communication on HTTPS:
Enter $NMSROOT/bin/perl $NMSROOT/bin/camssl.pl -disable
Step 2 Restart the Daemon Manager:
On Windows:
Enter net stop crmdmgtd
Enter net start crmdmgtd
On Solaris:
Enter /etc/init.d/dmgtd stop
Enter /etc/init.d/dmgtd start
Q. How do I change web server port numbers?
A. To change the web server port numbers, you must execute separate commands for both Windows and Solaris.
On Solaris:
You can change the web server port numbers for the webservers. You can also change both the HTTP and HTTPS port numbers. To change the port numbers you must login as CiscoWorks Server administrator, and run the following command at the prompt:
/opt/CSCOpx/MDC/Apache/bin/changeport
If you run this command without any command line parameter, CiscoWorks displays:
*** CiscoWorks Webserver port change utility ***
Usage: changeport <port number> [-s] [-f]
where
port number—The new port number that should be used
-s—Changes the SSL port instead of the default HTTP port
-f—Forces port change even if Daemon Manager detection FAILS.
Note Do not use this option by default. Use it only when CiscoWorks instructs you to.
For example, you can enter:
changeport 1744—Changes the CiscoWorks web server HTTP port to use 1744.
Or,
changeport port number -s—Changes the CiscoWorks web server HTTPS port to use the specified port number.
The restrictions that apply to the specified port number are:
•Port numbers less than 1025 are not allowed except 80 (HTTP) and 443 (HTTPS). Also port 80 is not allowed for SSL port and port 443 is not allowed for HTTP port.
•The specified port should not be used by any other service or daemon. The utility checks for active listening ports and ports listed in /etc/services. If any conflict is found it rejects the specified port.
•The port number must be a numeric value in the range 1026 - 65000. Values outside this range and non-numeric values are not allowed.
•If port 80 or 443 is specified for any of the webservers, that webserver process is started as root. This is because ports lower than 1026 are allowed to be used only by root in Solaris.
However, according to Apache behavior, only the main webserver process runs as root, and all the child processes will run as casuser:casusers. Only the child processes serve the external requests.
The main process which runs as root monitors the child processes. It does not accept any HTTP requests. Owing to this, Apache ensures that a root process is not exposed to the external world and thus ensures security.
•If you do not want CiscoWorks processes to run as root, do not use the ports 80 and 443.
When you execute the utility with the appropriate options, it displays messages on the tasks it performs.
This utility lists out all the files that are being updated. Before updating, the utility will back up all the affected files in /opt/CSCOpx/conf/backup and creates appropriate unique sub-directories.
It also creates a new file index.txt. This text file contains information about the changed port and a list of all the files that are backed up and their actual location in the CiscoWorks directory.
A sample backup maybe similar to:
|--README.txt (Note the purpose of this directory as it is initially empty)
`--/AAAtpaG03_Ciscobak (Autogenerated unique backup directory).
|--index.txt (The backup file list)
|--httpd.conf (Webserver config file)
|--md.properties (CiscoWorks config elements)
|--mdc_web.xml (Common Services application config file)
|--regdaemon.key (Common Services config registry key file)
|--regdaemon.xml (Common Services config registry data file)
|--rootapps.conf (CiscoWorks daemons using privileged ports)
|--services (The system /etc/services file)
|--ssl.properties (CiscoWorks config elements for SSL mode)
`--vms_web.xml (Common Services application config file)
Note All the above files and the unique directories are stored with read only permission to casuser:casusers. To ensure the security of the backup files, only the CiscoWorks Server administrator has write permissions.
The change port utility displays messages to the console during execution. These messages contain information about the directory where the backup files are being stored. These messages are also logged to a file, changeport.log
This file is saved to the directory:
/var/adm/CSCOpx/log/changeport.log
This file contains the date and time stamps to indicate when the log entries were created.
On Windows:
You can change the web server port numbers for the Common Services Webserver. You can also change both the HTTP and HTTPS port numbers.
To change the port numbers you must have administrative privileges. Run the following command at the prompt:
CSCOpx\MDC\Apache\changeport.exe
If you execute this utility without any command line parameter, CiscoWorks displays the following usage text:
*** Common Services Webserver port change utility ***
Usage: changeport <port number> [-s] [-f]
where:
port number—The new port number that should be used
-s—Change the SSL port instead of the default HTTP port
-f—Force port change even if Daemon Manager detection fails.
Note Do not use this option by default. Use it only when CiscoWorks instructs you to.
For example, you can enter:
changeport 1744—to change the CiscoWorks web server HTTP port to use 1744.
Or,
changeport port number -s—Changes the CiscoWorks web server HTTPS port to use the specified port number.
Note If you change the port after installation, CiscoWorks will not launch from Start menu (Start > Programs > CiscoWorks > CiscoWorks). You have to manually invoke the browser and specify the URL, with the changed port number.
The restrictions that apply to the specified port number are:
•Port numbers less than 1025 are not allowed except 80 (HTTP) and 443 (HTTPS). Also port 80 is not allowed for HTTPS port and port 443 is not allowed for HTTP port.
•The specified port should not be used by any other service or daemon. The utility checks for active listening ports and if any conflict is found the utility rejects the specified port.
There is no reliable way to determine whether any other service or application is using a specified port. If the service or application is running and actively listening on a port, it can be easily detected.
However, if the service is currently stopped, there is no way that the utility can determine what port it uses. This is because on Windows there is no common port registry equivalent to /etc/services as in UNIX.
The port number must be a numeric value in the range 1026 - 65000. Values outside this range and non-numeric values are not allowed.
When you execute the utility with the appropriate options, it displays messages on the actions it is performing.
It lists out all the files that are being updated. Before updating, the utility will back up all the affected files in CSCOpx\conf\backup and creates appropriate unique sub-directories.
It also creates a new file index.txt, which contains information about the changed port and a list of all the files that are backed up and their actual location in the CiscoWorks directory.
A sample backup may be similar to:
|--README.txt (Notes the purpose of this dir as it is initially empty)
`--\skc03._Ciscobak (Autogenerated unique backup directory).
|--index.txt (The backup file list)
|--httpd.conf (Webserver config file)
|--md.properties (CiscoWorks config elements)
|--mdc_web.xml (Common Services application config file)
|--regdaemon.key (Common Services config registry key file)
|--regdaemon.xml (Common Services config registry data file)
|--ssl.properties (CiscoWorks config elements for SSL mode)
`--vms_web.xml (Common Services application config file)
Note All the above files and the unique directories are stored with read only permissions. Only the administrator and casuser have write permissions, to ensure the security of the backup files.
The change port utility displays messages to the console during execution. These messages contain information about the directory where the backup files are being stored. These messages are also logged to a file, changeport.log.
This file is saved to the directory:
NMSROOT\log\changeport.log
This log file contains the date and time stamps to indicate when the log entries were created.
Q. Ho do I increase Tomcat heap size?
A. To increase Tomcat heap size:
Step 1 Stop Daemon Manager.
•On Solaris:
Run /etc/init.d/dmgtd stop
•On Windows:
Run net stop CRMdmgtd
Step 2 Run $NMSROOT/bin/perl $NMSROOT/bin/ModifyTomcatHeap.pl max heap in MB
Step 3 Start Daemon Manager.
•On Solaris:
Run /etc/init.d/dmgtd stop
•On Windows:
Run net start CRMdmgtd
If Tomcat is already configured for higher memory than what you specify when you run the command, it displays message stating this, and exits.
Q. How do I enable debugging in MICE?
A. To enable debugging in MICE:
Step 1 Go to NMSROOT/MDC/tomcat/webapps/classic/WEB-INF/web.xml.
You have to edit the following section of the file:
<context-param>
<param-name>DEBUG</param-name>
<param-value>false</param-value>
<description>mice debug enabling</description>
</context-param>
Step 2 Change <param-value>false</param-value> to
<param-value>true</param-value>
Q. What does cmf stand for?
A. The cmf acronym stands for Common Management Foundation. This phrase describes the set of management services provided by the CiscoWorks Server. cmf is synonymous with Common Services.
Troubleshooting Suggestions
Use the suggestions in Table 8-4 to resolve errors or other problems with the CiscoWorks Server.
Table 8-4 Troubleshooting Suggestions
Symptom
|
Probable Cause
|
Possible Solutions
|
Authorization required. Please log in with your username and password.
|
Incompatible browser causing cookie failure (unable to retrieve cookie).
|
Verify that you have Accept all cookies enabled. Refer to the installation documentation for supported Internet Explorer and Netscape Navigator software and setup procedures.
|
Daemon Manager could not start. The port is in use.
|
The operating system has not yet reallocated the port.
|
Make sure all CiscoWorks processes are terminated (/usr/ucb/ps -auxww | grep CSCO). Wait five to ten minutes, then try to restart the Daemon Manager.
|
User has forgotten his password.
|
Common Services cannot recover forgotten passwords.
|
A system administrator-level user must either change the password or delete and then add the user again.
|
You are logged out of the CiscoWorks Server.
|
Changes in the login module configuration file might not be correct.
Authentication server might be down and there were no fallback logins set.
|
1. Log on as root.
2. On Windows:
Run NMSROOT/bin/ResetLoginModule.pl
On Solaris:
Run opt/CSCOpx/bin/ResetLoginModule.pl
3. Restart Daemon Manager.
|
The Log File Status window displays files that exceed their limit.
|
Files need to be backed up so that file size will be reset to zero.
|
1. Stop all processes.
2. Enter the log file maintenance command:
a. On UNIX: $NMSROOT/cgi-bin/admin/
b. On Windows: NMSROOT\
cgi-bin\admin\
3. Restart all processes.
|
Error message in the logfile: Connection Refused. Check the Device is SSH supported or not.
|
Device is not SSH enabled or the server is not authorized to initiate SSH connection.
|
1. Check whether the device is up or not.
2. Try connecting to the device with a commercial SSH client.
If you are able to connect, go to step 3.
If you are not able to connect, check whether the device is running SSH enabled (K2 or K9) image.
•If it is not the correct image, download the appropriate image to the device.
•If you have the correct image, then see whether you have created RSA key pairs in the device. Creating RSA keys will enable SSH in the device.
3. Check whether your server or network is authorized to initiate SSH connections to device.
|
After installation, while starting the daemon manager, the following error message is displayed:
Found Non-SSL compliant Applications. Please disable SSL and then start the Daemon Manager
(Solaris only)
|
Found Non-SSL compliant products that do not function in SSL enabled mode.
|
Disable SSL from CLI and then start the daemon manager.
|
After installation, while starting the daemon manager, the following error message is displayed:
Service Not responded in a timely fashion
|
Found Non-SSL compliant products that do not function in SSL enabled mode.
|
Disable SSL from CLI and then start the daemon manager.
|
