Table Of Contents
Performance Counters Shown in the Detailed Device View
Performance Counters Shown in the Detailed Device View
This topic provides definitions for the performance counters shown in the Detailed Device View. This topic also lists the type of polling settings that control whether or not Operations Manager collects the performance counters. For information about enabling and disabling polling, see Editing Polling Parameters, page 18-14. For details on all performance counter objects and MIB objects that Operations Manager uses, see MIBs Polled and Perfmon Counter Objects Used, page B-1. The following performance counters are displayed in the Detailed Device View:
•
BRI Channel Status for CCM GW
•BRI Channel Status for IOS GW
•Cisco Unified Communications Manager
•CCM Port and CPU Usage
•CCM GW Port Usage
•CCM Usage
•CCM - Analog Access GW Usage
•CCM - CTI Manager Usage
•CCM - H323 GW Usage
•CCM - Location Usage
•CCM - Media Streaming Application Usage
•CCM - MOH Device Usage
•CCM - MTP Usage
•CCM - Transcoder
•Cisco Analog Access
•Cisco Unified Communications Manager Attendant Console
•Cisco IPCC Router Usage
•Cisco Messaging Interface
•Cisco SRST Usage
•Cisco TFTP Server
•CME Usage
•Consolidated DSP Usage
•CPU Usage
•CU Usage
•CU Connection Usage
•CUE Usage
•DPA Port and CPU Usage
•DSP Usage
•E1 CAS Channel Status for IOS GW
•E1 PRI Channel Status for CCM GW
•E1 PRI Channel Status for IOS GW
•E1 PRI Usage for CCM GW
•FXO Port Usage for CCM GW
•FXS Port Usage for CCM GW
•Gatekeeper Zone Statistics
•Hardware Conference Bridge
•Memory Usage
•Server Memory Usage
•SIP Device Usage
•Software Conference Bridge
•T1 CAS Channel Status for CCM GW
•T1 CAS Channel Status for IOS GW
•T1 CAS Usage for CCM GW
•T1 PRI Channel Status for CCM GW
•T1 PRI Usage for CCM GW
BRI Channel Status for CCM GW
The set of performance counters in Table A-1 is displayed for each BRI port in the MGCP gateway.
Table A-1 BRI Channel Status for Cisco Unified Communications Manager-Controlled MGCP Gateway
Counters
|
Description
|
DS1 name
|
DS1 name
|
Channel Status [1]
|
B channel
0=unknown, 1=out-of-service,
2=idle, 3=busy, 4=reserved
|
Channel Status [2]
|
B channel
0=unknown, 1=out-of-service,
2=idle, 3=busy, 4=reserved
|
Channel Status [3]
|
D channel
0=out-of-service, 1=in-service
|
BRI Channel Status for IOS GW
The set of performance counters in Table A-2 are displayed for each BRI port in the Cisco IOS gateway registered.
Table A-2 BRI Channel Status for Cisco IOS Gateway
Counters
|
Description
|
DS1 Name
|
DS1 name
|
B Channel Status [n]
Note Displayed for each of 2 channels with n from 0 through 1.
|
200=idle, 300=unknown, 302=voice, 303=unrestrictedDigital, 304=unrestrictedDigital56, 305=restrictedDigital, 306=audio31, 307=audio7, 308=video, 309=packetSwitched
|
Cisco Unified Communications Manager
Table A-3 lists performance counters for the Cisco Unified Communications Manager.
Note Polling for these counters is enabled by default and is controlled by Voice Health Settings.
Table A-3 Cisco Unified Communications Manager
Counter
|
Description
|
Cisco Unified Communications Manager Heartbeat
|
An incremental count that indicates that Cisco Unified Communications Manager is up and running. If the count does not increase, it indicates that Cisco Unified Communications Manager is down.
|
Number of Failed Attempts to Allocate Hardware Resources
|
Number of times this Cisco Unified Communications Manager attempted to allocate a hardware conference resource from those that are registered to this Cisco Unified Communications Manager, when none were available.
|
Number of Failed Attempts to Allocate Software Resources
|
Number of times this Cisco Unified Communications Manager attempted to allocate a software conference resource from those that are registered to this Cisco Unified Communications Manager, when none were available.
|
Number of Times No Transcoder Resources Were Available for Allocation
|
Number of times that Cisco Unified Communications Manager attempted to allocate a transcoder resource from one of the transcoder devices that is registered to this Cisco Unified Communications Manager, when none were available.
|
Number of Times No Unicast MOH Resources Were Available for Allocation
|
Number of times that the Media Resource Manager attempted to allocate a Music On Hold (MOH) resource when none were available.
|
Number of Times No Multicast MOH Resources were Available for Allocation
|
Number of times no multicast MOH resources were available for allocation.
|
Number of Failed Attempts to Allocate an MTP Resource
|
Number of times that Cisco Unified Communications Manager attempted but failed to allocate an MTP resource from one of the MTP devices that is registered with this Cisco Unified Communications Manager.
|
Total Number of Calls, via the Location, that Failed Due to Lack of Bandwidth
|
Total number of calls via the location that failed due to lack of bandwidth.
|
Number of Signals Present in the Low-Priority Queue
|
Number of signals present in the low-priority queue.
|
Number of Signals Present in the Normal-Priority Queue
|
Number of signals present in the normal-priority queue.
|
Number of Signals Present in the High-Priority Queue
|
Number of signals present in the high-priority queue.
|
Number of MOH Connections Lost
|
Number of times that a connection was lost, since the Cisco IP Voice Media Streaming application service started.
|
Number of MTP Instances Started
|
Total number of MTP instances that have been started since the Cisco IP Voice Media Streaming application service started.
|
Number of Simplex Streams Connected to an MTP Device
|
Total number of simplex streams that have connected to the MOH server since the Cisco IP Voice Media Streaming application service started.
|
CCM GW Port Usage
Table A-4 lists performance counters for a Cisco Unified Communications Manager-controlled MGCP gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-4 Cisco Unified Communications Manager-Controlled MGCP Gateway Port Usage
Counters
|
Description
|
Number of Active Calls
|
Number of call legs active.
|
Total T1 PRI Channels
|
Number of T1 PRI channels configured on the MGCP gateway.
|
Active T1 PRI Channels
|
Number of T1 PRI channels active with voice calls.
|
Active Nonvoice T1 PRI Channels
|
Number of T1 PRI channels active with nonvoice calls.
|
Total E1 PRI Channels
|
Number of E1 PRI channels configured on the MGCP gateway.
|
Active E1 PRI Channels
|
Number of E1 PRI channels active with voice calls.
|
Active Nonvoice E1 PRI Channels
|
Number of E1 PRI channels active with nonvoice calls.
|
Total T1 CAS Channels
|
Number of T1 CAS channels configured on the MGCP gateway.
|
Active T1 CAS Channels
|
Number of T1 CAS channels active with voice calls.
|
Active Nonvoice T1 CAS Channels
|
Number of T1 CAS channels active with nonvoice calls.
|
Total E1 CAS Channels
|
Number of E1 CAS channels configured on the MGCP gateway.
|
Active E1 CAS Channels
|
Number of E1 CAS channels active with voice calls.
|
Active Nonvoice E1 CAS Channels
|
Number of E1 CAS channels active with nonvoice calls.
|
Total FXS Ports
|
Number of FXS ports configured on the MGCP gateway.
|
Active FXS Ports
|
Number of FXS ports active.
|
Total FXO Ports
|
Number of FXO ports configured on the MGCP gateway.
|
Active FXO Ports
|
Number of FXO ports active.
|
Total BRI Channels
|
Number of BRI channels configured on the MGCP gateway.
|
Active BRI Channels
|
Number of BRI channels active with voice calls.
|
Active Nonvoice BRI Channels
|
Number of BRI channels active with nonvoice calls.
|
Total EM Ports
|
Number of ear and mouth (E&M) ports configured on the Cisco IOS gateway.
|
Active EM Ports
|
Number of E&M ports active.
|
Percentage Active T1 CAS
|
T1 CAS voice utilization for the MGCP gateway.
|
Percentage Active E1 CAS
|
E1 CAS voice utilization for the MGCP gateway.
|
Percentage Active FXS
|
FXS port utilization for the MGCP gateway.
|
Percentage Active FXO
|
FXO port utilization for the MGCP gateway.
|
Percentage Active T1 PRI
|
T1 PRI voice utilization for the MGCP gateway.
|
Percentage Active E1 PRI
|
E1 PRI voice utilization for the MGCP gateway.
|
Percentage Active EM
|
E&M voice utilization for the MGCP gateway.
|
CCM Port and CPU Usage
Table A-5 contains port usage and CPU usage for the Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-5 Port and CPU Usage on the Cisco Unified Communications Manager System
Counters
|
Description
|
CPU Usage [0]
|
Measured CPU utilization for CPU 1.
|
Number of Active Calls
|
Number of calls active. This counter shows calls that are fully established and in use. Calls in setup mode or in teardown mode are not reported by this count.
|
Total PRI Channels
|
Number of T1/E1 PRI channels that were defined on Cisco Unified Communications Manager.
|
Active PRI Channels
|
Number of T1/E1 PRI channels that were active.
|
Total T1 E1 Channels
|
Number of defined T1/E1 CAS channels on Cisco Unified Communications Manager.
|
Active T1 E1 Channels
|
Number of T1/E1 CAS channels that were active.
|
Total FXS
|
Number of defined FXS ports on Cisco Unified Communications Manager platform.
|
Active FXS
|
Number of FXS ports that were active.
|
Total FXO
|
Number of defined FXO ports on Cisco Unified Communications Manager platform.
|
Active FXO
|
Number of FXO ports that were active.
|
CPU Usage [2]
|
(Optional) Measured CPU utilization for CPU 2.
|
CPU Usage [3]
|
(Optional) Measured CPU utilization for CPU 3.
|
CPU Usage [4]
|
(Optional) Measured CPU utilization for CPU 4.
|
CPU Usage [5]
|
(Optional) Measured CPU utilization for CPU 5.
|
Total CPU Usage
|
Measured CPU utilization for all CPUs.
|
Total T1 PRI Channels
|
Number of T1 PRI channels that were defined on Cisco Unified Communications Manager.
|
Active T1 PRI Channels
|
Number of T1 PRI channels that were active.
|
Total E1 PRI Channels
|
Number of E1 PRI channels that were defined on Cisco Unified Communications Manager.
|
Active E1 PRI Channels
|
Number of E1 PRI channels that were active.
|
Total BRI Channels
|
Number of BRI channels that were defined on Cisco Unified Communications Manager.
|
Active BRI Channels
|
Number of BRI channels that were active.
|
Calls Attempted
|
Number of calls attempted on this Cisco Unified Communications Manager.
|
Calls Completed
|
Number of calls completed on this Cisco Unified Communications Manager.
|
Calls in Progress
|
Number of calls in progress on this Cisco Unified Communications Manager.
|
Percentage Active T1 CAS
|
T1 CAS utilization for Cisco Unified Communications Manager.
|
Percentage Active FXS
|
FXS port utilization for Cisco Unified Communications Manager.
|
Percentage Active FXO
|
FXO port utilization for Cisco Unified Communications Manager.
|
Percentage Active T1 PRI
|
T1 PRI utilization for Cisco Unified Communications Manager.
|
Percentage Active E1 PRI
|
E1 PRI utilization for Cisco Unified Communications Manager.
|
Percentage Active BRI
|
BRI utilization for Cisco Unified Communications Manager.
|
IOS GW Port Usage
Table A-6 lists performance counters for a Cisco IOS gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings. For more information, see Notes on Record Type 102, page J-12.
Table A-6 Port Usage on a Cisco IOS Gateway
Counters
|
Description
|
Number of Active Calls
|
Number of call legs active.
|
Total T1 PRI Channels
|
Number of T1 PRI channels configured on the Cisco IOS gateway.
|
Active T1 PRI Channels
|
Number of T1 PRI channels active with voice calls.
|
Active Nonvoice T1 PRI Channels
|
Number of T1 PRI channels active with nonvoice calls.
|
Total E1 PRI Channels
|
Number of E1 PRI channels configured on the Cisco IOS gateway.
|
Active E1 PRI Channels
|
Number of E1 PRI channels active with voice calls.
|
Active Nonvoice E1 PRI Channels
|
Number of E1 PRI channels active with nonvoice calls.
|
Total T1 CAS Channels
|
Number of T1 CAS channels configured on the Cisco IOS gateway.
|
Active T1 CAS Channels
|
Number of T1 CAS channels active with voice calls.
|
Active Nonvoice T1 CAS Channels
|
Number of T1 CAS channels active with nonvoice calls.
|
Total E1 CAS Channels
|
Number of E1 CAS channels configured on the Cisco IOS gateway.
|
Active E1 CAS Channels
|
Number of E1 CAS channels active with voice calls.
|
Active Nonvoice E1 CAS Channels
|
Number of E1 CAS channels active with nonvoice calls.
|
Total FXS Ports
|
Number of FXS ports configured on the Cisco IOS gateway.
|
Active FXS Ports
|
Number of FXS ports active.
|
Total FXO Ports
|
Number of FXO ports configured on the Cisco IOS gateway.
|
Active FXO Ports
|
Number of FXO ports active.
|
Total BRI Channels
|
Number of BRI channels configured on the Cisco IOS gateway.
|
Active BRI Channels
|
Number of BRI channels active with voice calls.
|
Active Nonvoice BRI Channels
|
Number of BRI channels active with nonvoice calls.
|
Total EM Ports
|
Number of ear and mouth (E&M) ports configured on the Cisco IOS gateway.
|
Active EM Ports
|
Number of E&M ports active.
|
Percentage Active T1 CAS
|
T1 CAS voice utilization for the Cisco IOS gateway.
|
Percentage Active E1 CAS
|
E1 CAS voice utilization for the Cisco IOS gateway.
|
Percentage Active FXS
|
FXS port utilization for the Cisco IOS gateway.
|
Percentage Active FXO
|
FXO port utilization for the Cisco IOS gateway.
|
Percentage Active T1 PRI
|
T1 PRI voice utilization for the Cisco IOS gateway.
|
Percentage Active E1 PRI
|
E1 PRI voice utilization for the Cisco IOS gateway.
|
Percentage Active EM
|
E&M voice utilization for the Cisco IOS gateway.
|
CCM - H323 GW Usage
Table A-7 lists performance counters for a H323 gateway registered with Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-7 Cisco Unified Communications Manager—H323 Gateway Usage
Counters
|
Description
|
H323 Gateway Name
|
Name of the H323 gateway added to Cisco Unified Communications Manager.
|
Calls Active
|
Number of calls active through the H323 gateway added to the Cisco Unified Communications Manager.
|
Calls Attempted
|
Number of calls attempted through the H323 gateway added to the Cisco Unified Communications Manager.
|
Calls Completed
|
Number of calls completed through the H323 gateway added to the Cisco Unified Communications Manager.
|
Calls in Progress
|
Number of calls in progress through the H323 gateway added to the Cisco Unified Communications Manager.
|
CCM Usage
Table A-8 lists performance counters for a Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-8 Cisco Unified Communications Manager Usage
Counters
|
Description
|
MOH Total Multicast Resources
|
Total MOH multicast resources configured on Cisco Unified Communications Manager.
|
MOH Multicast Resources Active
|
Active MOH multicast resources on Cisco Unified Communications Manager.
|
MOH Multicast Resources Available
|
Available MOH multicast resources on Cisco Unified Communications Manager.
|
Percentage MOH Multicast Resources Active
|
MOH multicast resource utilization on Cisco Unified Communications Manager.
|
MOH Total Unicast Resources
|
Total MOH unicast resources configured on Cisco Unified Communications Manager.
|
MOH Unicast Resources Active
|
Active MOH unicast resources on Cisco Unified Communications Manager.
|
MOH Unicast Resources Available
|
Available MOH unicast resources on Cisco Unified Communications Manager.
|
Percentage MOH Unicast Resources Active
|
MOH unicast resource utilization on Cisco Unified Communications Manager.
|
MTP Total Resources
|
Total MTP resources configured on Cisco Unified Communications Manager.
|
MTP Resources Active
|
Active MTP resources on Cisco Unified Communications Manager.
|
MTP Resources Available
|
Available MTP resources on Cisco Unified Communications Manager.
|
Percentage MTP Resources Active
|
MTP resource utilization on Cisco Unified Communications Manager.
|
Transcoder Total Resources
|
Total number of transcoder resources on the Cisco Unified Communications Manager.
|
Transcoder Resources Active
|
Number of transcoder resources active on the Cisco Unified Communications Manager.
|
Transcoder Resources Available
|
Number of transcoder resources available on the Cisco Unified Communications Manager.
|
Percentage Transcoder Resources Active
|
Percentage of total transcoder resources on the Cisco Unified Communications Manager active.
|
Software Conference Total Resources
|
Total number of software conference resources on the Cisco Unified Communications Manager.
|
Software Conference Resources Active
|
Number of software conference resources on the Cisco Unified Communications Manager active.
|
Percentage Software Conference Resources Active
|
Percentage of total software conference resources on the Cisco Unified Communications Manager active.
|
Software Conference Active
|
Number of active software conferences on the Cisco Unified Communications Manager.
|
Software Conference Completed
|
Number of completed software conferences on the Cisco Unified Communications Manager.
|
Hardware Conference Total Resources
|
Total number of hardware conference resources on the Cisco Unified Communications Manager.
|
Hardware Conference Resources Active
|
Number of hardware conference resources on the Cisco Unified Communications Manager active.
|
Hardware Conference Resources Available
|
Number of hardware conference resources on the Cisco Unified Communications Manager available.
|
Hardware Conference Completed
|
Number of completed hardware conferences on the Cisco Unified Communications Manager.
|
Registered Analog Access Gateways
|
Number of analog access devices registered with the Cisco Unified Communications Manager.
|
Registered MGCP Gateways
|
Number of MGCP gateways registered with the Cisco Unified Communications Manager.
|
Registered Hardware Phones
|
Number of hardware phones registered with the Cisco Unified Communications Manager.
|
Registered Other Station Devices
|
Number of other station devices registered with the Cisco Unified Communications Manager.
|
CCM - Analog Access GW Usage
Table A-9 lists counters for analog access gateways registered to Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-9 Cisco Unified Communications Manager—Analog Access Gateway Usage
Counters
|
Description
|
Ports Active
|
Number of ports active on the analog access device registered to Cisco Unified Communications Manager.
|
CCM - CTI Manager Usage
Table A-10 lists performance counters for CTI Manager usage in Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings with the exception of Number of Active Links with the Cisco Unified Communications Manager, which is controlled by Voice Health Settings.
Table A-10 Cisco Unified CallManager CTI Manager Usage
Counters
|
Description
|
Total CTI Ports
|
Total number of registered CTI ports on Cisco Unified CallManager.
|
Number of Active Links with the Cisco Unified CallManager
Cisco Unified CallManager Link Active
Note Cisco Unified CallManager Link Active is displayed only when data for Number of Active Links with the Cisco Unified CallManager is not available.
|
Number of CTI links active on Cisco Unified CallManager.
|
CTI Connection Active
|
Number of CTI connections active on Cisco Unified CallManager.
|
Devices Open
|
Number of CTI devices open.
|
Lines Open
|
Number of CTI lines open.
|
CCM - Location Usage
Table A-11 lists counters for location usage in Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-11 Cisco Unified Communications Manager—Location Usage
Counters
|
Description
|
Location Name
|
Name of the location defined in Cisco Unified Communications Manager.
|
Bandwidth Maximum
|
Total bandwidth configured for the location.
|
Bandwidth Available
|
Available bandwidth for the location.
|
Bandwidth utilization
|
Utilization of the bandwidth for the location.
|
Calls in Progress
|
Number of calls in progress.
|
CCM - Media Streaming Application Usage
Table A-12 lists performance counters for media streaming application usage in Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-12 Cisco Unified Communications Manager—Media Streaming Application Usage
Counters
|
Description
|
Conferences Total
|
Total conferences on Cisco Unified Communications Manager.
|
Conferences Active
|
Active conferences on Cisco Unified Communications Manager.
|
Percentage Conferences Active
|
Percentage active conferences on Cisco Unified Communications Manager.
|
Conference Bridge Streams Total
|
Total conference streams on Cisco Unified Communications Manager.
|
Conference Bridge Streams Available
|
Available conference streams on Cisco Unified Communications Manager.
|
Conference Bridge Streams Active
|
Active conference streams on Cisco Unified Communications Manager.
|
Percentage Conference Bridge Streams Active
|
Percentage active conference streams on Cisco Unified Communications Manager.
|
MOH Audio Sources Active
|
Number of active MOH audio sources on Cisco Unified Communications Manager.
|
MOH Streams Total
|
Total number of MOH streams configured on Cisco Unified Communications Manager.
|
MOH Streams Available
|
Number of available MOH streams on Cisco Unified Communications Manager.
|
MOH Streams Active
|
Number of active MOH streams on Cisco Unified Communications Manager.
|
Percentage MOH Streams Active
|
Percentage active MOH streams on Cisco Unified Communications Manager.
|
MTP Connections Total
|
Total number of MTP connections on Cisco Unified Communications Manager.
|
MTP Instances Active
|
Number of active MTP instances on Cisco Unified Communications Manager.
|
MTP Streams Total
|
Total number of MTP streams on Cisco Unified Communications Manager.
|
MTP Streams Available
|
Number of available MTP streams on Cisco Unified Communications Manager.
|
MTP Streams Actives
|
Number of active MTP streams on Cisco Unified Communications Manager.
|
Percentage MTP Streams Active
|
Percentage active MTP streams on Cisco Unified Communications Manager.
|
CCM - MOH Device Usage
Table A-13 lists counters for a music on hold (MOH) device registered with Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-13 Cisco Unified Communications Manager—MOH Device Usage
Counters
|
Description
|
MOH Device Name
|
Name of the MOH device.
|
MOH Highest Active Resources
|
Highest active resources on the MOH device registered to Cisco Unified Communications Manager.
|
MOH Total Multicast Resources
|
Total number of multicast resources on the MOH device.
|
MOH Multicast Resources Available
|
Available multicast resources on the MOH device.
|
MOH Multicast Resources Active
|
Active multicast resources on the MOH device.
|
Percentage Multicast Resources Active
|
Percentage active multicast resources on the MOH device.
|
MOH Total Unicast Resources
|
Total number of unicast resources on the MOH device.
|
MOH Unicast Resources Available
|
Available unicast resources on the MOH device.
|
MOH Unicast Resources Active
|
Active unicast resources on the MOH device.
|
Percentage Unicast Resources Active
|
Percentage active unicast resources on the MOH device.
|
CCM - MTP Usage
Table A-14 lists counters for a media termination point (MTP) registered with Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-14 Cisco Unified Communications Manager—MTP Usage
Counters
|
Description
|
MTP Device Name
|
Name of the MTP device registered to Cisco Unified Communications Manager.
|
Resource Total
|
Total number of resources on the MTP device.
|
Resources Available
|
Available resources on the MTP device.
|
Resources Active
|
Active resources on the MTP device.
|
Percentage Resources Active
|
Percentage active resources on the MTP device.
|
CCM - Transcoder
Table A-15 lists counters for transcoder devices registered with Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-15 Cisco Unified Communications Manager—Transcoder
Counter
|
Description
|
Transcoder Name
|
Name of the transcoder.
|
Transcoder Total Resources
|
Total number of resources on the transcoder device.
|
Transcoder Resources Available
|
Available resources on the transcoder device.
|
Transcoder Resources Active
|
Active resources on the transcoder device.
|
Percentage Transcoder Resources Active
|
Percentage active resources on the transcoder device.
|
Cisco Analog Access
Table A-16 lists counters for analog access gateway.
Note Polling for these counters is enabled by default and is controlled by Voice Health Settings.
Table A-16 Cisco Analog Access
Counters
|
Description
|
Number of Ports Currently in Use
|
Number of ports active on the analog access device registered to Cisco Unified Communications Manager.
|
Number of Ports that Are out of Service
|
Number of ports out of service. This only applies to Loop Start and Ground Start trunks.
|
Number of Outbound Calls Attempted when Ports Were Busy
|
Number of times that a call was attempted through this analog access when no ports were available.
|
Cisco Unified Communications Manager Attendant Console
Table A-17 lists counters for Cisco Unified Communications Manager Attendant Console.
Note Polling for these counters is enabled by default and is controlled by Voice Health Settings.
Table A-17 Cisco Unified Communications Manager Attendant Console
Counters
|
Description
|
Cisco Unified Communications Manager Line Link Status
|
The line link state. It can be any of the following: 0, 1, 10, or 11.
|
Attendant Console Heartbeat
|
An incremental count that indicates whether the Telephony Call Dispatcher (TCD) service is up and running. If the count does not increase, it indicates that the TCD service is down.
|
Cisco IPCC Router Usage
Table A-18 lists performance counters for a Cisco IPCC router.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-18 Cisco IPCC Router Usage
Counter
|
Description
|
IPCC Router Name
|
Router name.
|
IPCC Instance Name
|
Name of IPCC instance.
|
Agents Logged In
|
Number of contact center agents currently logged in.
|
Calls in Progress
|
Number of calls in progress.
|
Calls per Second
|
Number of inbound calls per second.
|
Cisco Messaging Interface
Table A-19 lists counters for Cisco Messaging Interface.
Note Polling for these counters is enabled by default and is controlled by Voice Health Settings.
Table A-19 Cisco Messaging Interface
Counter
|
Description
|
Messaging Heartbeat
|
An incremental count that indicates whether the Cisco Messaging Interface (CMI) service is up and running. If the count does not increase, it indicates that the CMI service is down.
|
Cisco SRST Usage
Table A-20 lists counters for Cisco Survivable Remote Site Telephony (SRST) usage information.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-20 Cisco SRST Usage
Counter
|
Description
|
Time in SRST Mode
|
Cumulative number of minutes the SRST device was in SRST mode.
|
Cisco TFTP Server
Table A-21 lists counters for Cisco TFTP Server.
Note Polling for these counters is enabled by default and is controlled by Voice Health Settings.
Table A-21 Cisco TFTP Server
Counter
|
Description
|
TFTP Heartbeat
|
An incremental count that indicates whether the TFTP server is up and running. If the count does not increase, it indicates that the TFTP server is down.
|
TFTP Requests Aborted
|
Number of times a TFTP client-initiated TFTP transfer was aborted.
|
CME Usage
Table A-22 lists performance counters for a Cisco Unified Communications Manager Express.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-22 Cisco Unified Communications Manager Express
Counters
|
Description
|
Number of Active Call Legs
|
Number of ephone call legs active.
|
Maximum Ephones
|
Maximum number of ephones that can be configured on the Cisco Unified Communications Manager Express.
|
Registered Ephones
|
Number of ephones registered.
|
Percentage Ephones Registered
|
Percentage of ephones that are registered.
|
Number of Configured Key Ephones
|
Number of key ephones configured.
|
Number of Registered Key Ephones
|
Number of key ephones registered.
|
Percentage Key Ephones Registered
|
Percentage of configured key ephones that are registered.
|
Ephones Seen
|
Maximum number of sessions configured on the CME.
|
Consolidated DSP Usage
Table A-23 lists counters for consolidated DSP usage on a Cisco IOS device.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
.
Table A-23 Consolidated DSP Usage
Counters
|
Description
|
Total DSP Channels
|
Total number of DSP channels on the device.
|
Total Active DSP Channels
|
Number of active DSP channels on the device.
|
Total In-Use DSP Channels
|
Number of DSP channels on the device that are reserved for serving calls.
|
Percentage Active DSP Channels
|
Percentage of DSP channels active on the device.
|
CPU Usage
Table A-24 lists counters for CPU usage on a Cisco IOS device, such as:
•Gateways and gatekeepers
•SRST devices
•Cisco Unity Express
•Cisco Unified Communications Manager Express
Table A-24 CPU Usage
Counters
|
Description
|
IOS Device Name
|
Name of Cisco IOS device.
|
CPU 1 5 Seconds
|
Overall CPU-busy percentage for CPU 1 in the last 5-second period; recorded at time stamp.
|
CPU 1 1 Minute
|
Overall CPU-busy percentage for CPU 1 in the last 1-minute period; recorded at time stamp.
|
CPU 1 5 Minutes
|
Overall CPU-busy percentage for CPU 1 in the last 5-minute period; recorded at time stamp.
|
CPU 2 5 Seconds
|
Overall CPU-busy percentage for CPU 2 in the last 5-second period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 2 is not present.
|
CPU 2 1 Minutes
|
Overall CPU-busy percentage for CPU 2 in the last 1-minute period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 2 is not present.
|
CPU 2 5 Minutes
|
Overall CPU-busy percentage for CPU 2 in the last 5-minute period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 2 is not present.
|
CPU 3 5 Seconds
|
Overall CPU-busy percentage for CPU 3 in the last 5-second period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 3 is not present.
|
CPU 3 1 Minute
|
Overall CPU-busy percentage for CPU 3 in the last 1-minute period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 3 is not present.
|
CPU 3 5 Minutes
|
Overall CPU-busy percentage for CPU 3 in the last 5-minute period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 3 is not present.
|
CPU 4 5 Seconds
|
Overall CPU-busy percentage for CPU 4 in the last 5-second period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 4 is not present.
|
CPU 4 1 Minute
|
Overall CPU-busy percentage for CPU 4 in the last 1-minute period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 4 is not present.
|
CPU 4 5 Minutes
|
Overall CPU-busy percentage for CPU 4 in the last 5-minute period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 4 is not present.
|
CPU 5 5 Seconds
|
Overall CPU-busy percentage for CPU 5 in the last 5-second period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 5 is not present.
|
CPU 5 1 Minutes
|
Overall CPU-busy percentage for CPU 5 in the last 1-minute period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 5 is not present.
|
CPU 5 5 Minutes
|
Overall CPU-busy percentage for CPU 5 in the last 5-minute period; recorded at time stamp.
Asterisk (*) in this field indicates that CPU 5 is not present.
|
CU Usage
Table A-25 lists counters for Cisco Unity.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-25 Cisco Unity Usage
Counter
|
Description
|
Total Ports
|
Total number of ports
|
Active Ports
|
Number of ports that are active
|
Percentage Active Ports
|
Percentage of total ports that are active
|
Total Inbound Ports
|
Total number of inbound ports
|
Active Inbound Ports
|
Number of active inbound ports
|
Percentage Active Inbound Ports
|
Percentage of total inbound ports that are active
|
Total Outbound Ports
|
Total outbound ports
|
Active Outbound Ports
|
Number of active outbound ports
|
Percentage Active Outbound Ports
|
Percentage of total outbound ports that are active
|
CU Connection Usage
Counters for Cisco Unity Connection have the same names and definitions as those for Cisco Unity; see Table A-25.
CUE Usage
Table A-26 lists counters for Cisco Unity Express mailbox usage.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-26 Cisco Unity Express Usage
Counters
|
Description
|
Licensed Mailboxes
|
Number of mailboxes that Cisco Unity Express is licensed for.
|
Orphaned Mailboxes
|
Number of mailboxes on Cisco Unity Express that are orphaned.
|
Percentage Orphaned Mailboxes
|
Percentage of orphaned mailboxes on Cisco Unity Express.
|
Maximum Sessions
|
Maximum number of sessions configured on Cisco Unity Express.
|
Sessions Used
|
Number of sessions used.
|
Percentage Sessions Used
|
Utilization of the sessions.
|
Licensed Capacity
|
Minutes of storage that the Cisco Unity Express is licensed for.
|
Allocated Capacity
|
Cumulative number of minutes of storage allocated to the mailboxes.
|
Used Capacity
|
Cumulative number of minutes of storage used by the mailboxes.
|
Capacity Used for Messages
|
Cumulative number of minutes of storage used for storing messages.
|
Free Capacity
|
Number of minutes of storage available.
|
Percentage of Time Used
|
Utilization of the storage on the Cisco Unity Express system.
|
Current Number of Messages
|
Cumulative number of messages stored in the mailboxes.
|
Current Number of Saved Messages
|
Cumulative number of saved messages in the mailboxes.
|
Messages Left
|
Cumulative number of messages left in the mailboxes since the last reboot of the Cisco Unity Express system.
|
Messages Retrieved
|
Cumulative number of messages retrieved in the mailboxes since the last reboot of the Cisco Unity Express system.
|
Messages Deleted
|
Cumulative number of messages deleted from the mailboxes since last reboot of the Cisco Unity Express system.
|
Number of Busy Mailboxes
|
Number of busy mailboxes.
|
Number of Mailboxes More than 90 Percent Full
|
Number of mailboxes that are 90% or more full.
|
DPA Port and CPU Usage
Table A-27 contains counters for Cisco Digital PBX Adapter (DPA) port usage.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-27 DPA Port and CPU Usage
Counter
|
Description
|
Total Voice Mail Ports
|
Number of voice mail ports on DPA.
|
Active Voice Mail Ports
|
Number of voice mail ports that are active.
|
Total PBX Ports
|
Number of PBX ports on DPA.
|
Active PBX Ports
|
Number of PBX ports that are active.
|
Unassigned Ports
|
Number of DPA ports that are not in use.
|
Percentage Active Voice Mail
|
Voice mail port utilization for the DPA.
|
Percentage Active PBX
|
PBX port utilization for the DPA.
|
CPU 5 Seconds
|
Overall CPU-busy percentage in the last 5-second period.
|
CPU 1 Minute
|
Overall CPU-busy percentage in the last 1-minute period.
|
CPU 5 Minutes
|
Overall CPU-busy percentage in the last 5-minute period.
|
DSP Usage
Table A-28 contains digital signal processor (DSP) usage information on Cisco IOS gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings. For additional information, see Cisco IOS Gateway Digital Signal Processor Usage—Record Type 109, page J-21.
Table A-28 DSP Usage
Counters
|
Description
|
Index
|
An index assigned to the DSP.
|
State
|
1=active, 2=shutdown.
|
Total Channels
|
Number of channels on DSP.
|
Active Channels
|
Number of channels on DSP that are active.
|
In-Use Channels
|
Number of channels reserved for serving calls.
|
E1 CAS Channel Status for IOS GW
The set of performance counters in Table A-29 is displayed for each E1 CAS port in the Cisco IOS gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-29 E1 CAS Channel Status for Cisco IOS Gateway
Counters
|
Description
|
DS1 Name
|
DS1 name
|
Channel Status [n]
Note Displayed for each of 31 channels with n from 0 through 30.
|
200=idle, 300=unknown, 301=other, 302=voice, 303=unrestrictedDigital, 304=unrestrictedDigital56, 305=restrictedDigital, 306=audio31, 307=audio7, 308=video, 309=packetSwitched, 310=fax, 312=unknown, 313=analog, 314=digital, 315=v110, 316=v120
|
E1 PRI Channel Status for CCM GW
The set of performance counters in Table A-30 is displayed for each E1 PRI port in the Cisco Unified Communications Manager-controlled MGCP gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-30 E1 PRI Channel Status for Cisco Unified Communications Manager-Controlled MGCP Gateway
Counters
|
Description
|
DS1 Name
|
DS1 name
|
Channel Status [n]
Note Displayed for each of 31 channels with n from 0 through 30.
|
0=unknown, 1=out-of-service, 2=idle, 3=busy, 4=reserved
|
E1 PRI Channel Status for IOS GW
The set of performance counters in Table A-31 is displayed for each E1 PRI port in the Cisco IOS gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-31 E1 PRI Channel Status for Cisco IOS Gateway
Counters
|
Description
|
DS1 Name
|
DS1 name
|
Channel Status [n]
Note Displayed for each of 31 channels with n from 0 through 30.
|
200=idle, 300=unknown, 301=other, 302=voice, 303=unrestrictedDigital, 304=unrestrictedDigital56, 305=restrictedDigital, 306=audio31, 307=audio7, 308=video, 309=packetSwitched, 310=fax, 312=unknown, 313=analog, 314=digital, 315=v110, 316=v120
|
E1 PRI Usage for CCM GW
The set of performance counters in Table A-32 is displayed for each E1 PRI in the Cisco Unified Communications Manager-controlled MGCP gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-32 E1 PRI Usage for Cisco Unified Communications Manager-Controlled MGCP Gateway
Counters
|
Description
|
CCM Name
|
Cisco Unified Communications Manager that the MGCP gateway is registered with.
|
DS1 Name
|
Name of DS1.
|
Calls Completed
|
Number of calls completed on this E1 PRI port on the gateway.
|
Outbound Busy Attempts
|
Number of outbound busy attempts on this E1 PRI port on the gateway.
|
FXO Port Usage for CCM GW
The set of performance counters in Table A-33 is displayed for each FXO port in the Cisco Unified Communications Manager-controlled MGCP gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-33 FXO Port Usage for Cisco Unified Communications Manager-Controlled MGCP Gateway
Counters
|
Description
|
CCM Name
|
Cisco Unified Communications Manager that the MGCP gateway is registered with.
|
FXO Port Name
|
Name of FXO port.
|
Calls Completed
|
Number of calls completed on this FXO port on the gateway.
|
Outbound Busy Attempts
|
Number of outbound busy attempts on this FXO port on the gateway.
|
FXS Port Usage for CCM GW
The set of performance counters in Table A-34 is displayed for each FXS port in the Cisco Unified Communications Manager-controlled MGCP gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-34 FXS Port Usage for Cisco Unified Communications Manager-Controlled MGCP Gateway
Counters
|
Description
|
CCM Name
|
Cisco Unified Communications Manager that the MGCP gateway is registered with.
|
FXS Port Name
|
Name of FXS port.
|
Calls Completed
|
Number of calls completed on this FXS port on the gateway.
|
Outbound Busy Attempts
|
Number of outbound busy attempts on this FXS port on the gateway.
|
Gatekeeper Zone Statistics
The set of performance counters in Table A-35 is displayed for each gatekeeper zone.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-35 Gatekeeper Zone Statistics
Counters
|
Description
|
Zone Name
|
Name of zone.
|
Zone Domain
|
Name of zone domain.
|
Zone Type
|
Indicates whether the zone is local or remote.
|
Total Bandwidth
|
Total bandwidth in 100 bps configured for local zone, or one of the following:
-1=bandwidth limitation not set.
*=field is not applicable (when record is for a remote zone).
|
Allocated Bandwidth
|
Bandwidth in 100 bps allocated to calls for local zone, or asterisk (*) to indicate that the field is not applicable (when record is for a remote zone).
|
Total Interzone Bandwidth
|
Total interzone bandwidth in 100 bps configured for local zone, or one of the following:
-1=bandwidth limitation not set.
*=field is not applicable (when record is for a remote zone).
|
Allocated Interzone Bandwidth
|
Bandwidth in 100 bps allocated to calls for the local zone, or asterisk (*) to indicate that the field is not applicable (when record is for a remote zone).
|
Number of Admission Rejections
|
Cumulative number of admission rejections for local zone, or asterisk (*) to indicate that the field is not applicable (when record is for a remote zone).
|
Number of Admission Confirms
|
Cumulative number of admission confirms for local zone, or asterisk (*) to indicate that the field is not applicable (when record is for a remote zone).
|
Number of Location Requests
|
Cumulative number of location requests for remote zone, or asterisk (*) to indicate that the field is not applicable (when record is for a local zone).
|
Number of Add Lookup Failures
|
Cumulative number of times the gatekeeper is unable to resolve an address.
|
Number of Endpoint Timeouts
|
Cumulative number of times the time to live has expired for an endpoint in this zone.
|
Number of Other Failures
|
Cumulative number of call attempts which have failed for reasons other than endpoint timeouts or address lookup failures.
|
Percentage Allocated Bandwidth
|
Bandwidth utilization for the local zone.
|
Percentage Allocated Interzone Bandwidth
|
Interzone bandwidth utilization for the local zone.
|
Hardware Conference Bridge
Table A-36 lists counters for a hardware conference bridge registered with Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-36 Hardware Conference Bridge
Counters
|
Description
|
Bridge Name
|
Name of the hardware conference bridge registered to Unified Communications Manager.
|
Conferences Completed
|
Number of conferences completed on this hardware conference bridge.
|
Conferences Active
|
Number of conferences active on this hardware conference bridge.
|
Total Resources
|
Total number of resources on this hardware conference bridge.
|
Available Resource
|
Available resources on this hardware conference bridge.
|
Active Resource
|
Active resources on this hardware conference bridge.
|
Percentage Active Resources
|
Percentage of active resources on this hardware conference bridge.
|
Memory Usage
Table A-37 lists counters for memory usage; these counters might be displayed for any of the following:
•Cisco Unified Communications Manager Express
•Cisco IOS gateway or gatekeeper
•Cisco Unity Express
•SRST devices
•Cisco IOS gateways and gatekeepers
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-37 Memory Usage
Counters
|
Description
|
Processor Used
|
Amount of memory in bytes.
|
Processor Free
|
Amount of memory in bytes.
|
Processor Largest Free
|
Amount of memory in bytes.
|
I/O Used
|
Amount of memory in bytes.
|
I/O Free
|
Amount of memory in bytes.
|
I/O Largest Free
|
Amount of memory in bytes.
|
PCI Used
|
Amount of memory in bytes.
|
PCI Free
|
Amount of memory in bytes.
|
PCI Largest Free
|
Amount of memory in bytes.
|
Fast Used
|
Amount of memory in bytes.
|
Fast Free
|
Amount of memory in bytes.
|
Fast Largest Free
|
Amount of memory in bytes.
|
Multibus Used
|
Amount of memory in bytes.
|
Multibus Free
|
Amount of memory in bytes.
|
Multibus Largest Free
|
Amount of memory in bytes.
|
Percentage Processor Memory Used
|
Percentage processor memory utilization.
|
Percentage I/O Memory Used
|
Percentage I/O memory utilization.
|
Server Memory Usage
Table A-38 lists counters for memory usage information for a server running one of the following: Cisco Unified Communications Manager, IP Contact Center, Cisco Unity, or Cisco Unity Connection.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-38 Server Memory Usage
Counters
|
Description
|
Total Memory in Kilobytes
|
Total RAM in kilobytes.
|
Used Memory in Kilobytes
|
Used RAM in kilobytes.
|
Free Memory in Bytes
|
Free RAM in kilobytes.
|
Percentage Used Memory
|
Percentage of used memory.
|
Kilobytes Buffered
|
Linux buffered memory in kilobytes.
|
Kilobytes Cached
|
Linux cached memory in kilobytes.
|
Kilobytes Shared
|
Linux shared memory in kilobytes.
|
Kilobytes Total Swap
|
Linux total swap memory in kilobytes.
|
Kilobytes Used Swap
|
Linux used swap memory in kilobytes.
|
Kilobytes Free Swap
|
Linux free swap memory in kilobytes.
|
Windows Cached Bytes
|
Windows cached memory in kilobytes.
|
Windows Commit Limit
|
Windows total virtual memory in kilobytes.
|
Windows Committed Bytes
|
Windows used virtual memory in kilobytes.
|
SIP Device Usage
Table A-39 lists counters for SIP devices registered with Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-39 SIP Device Usage
Counters
|
Description
|
SIP Device Name
|
Name of the SIP device.
|
Calls Active
|
Number of calls active.
|
Calls Attempted
|
Number of calls attempted.
|
Calls Completed
|
Number of calls completed.
|
Calls in Progress
|
Number of calls in progress.
|
Software Conference Bridge
Table A-40 lists counters for software conference bridge registered with Cisco Unified Communications Manager.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-39, Part 1 Software Conference Bridge
Counters
|
Description
|
Bridge Name
|
Name of the software conference bridge registered to Unified Communications Manager.
|
Conferences Completed
|
Number of conferences completed on this software conference bridge.
|
Conferences Active
|
Number of conferences active on this software conference bridge.
|
Total Resources
|
Total number of resources on this software conference bridge.
|
Available Resource
|
Available resources on this software conference bridge.
|
Active Resource
|
Active resources on this software conference bridge.
|
Percentage Active Resources
|
Percentage of active resources on this software conference bridge.
|
T1 CAS Channel Status for CCM GW
The set of performance counters in Table A-40 is displayed for each T1 CAS port in the Cisco Unified Communications Manager-controlled MGCP gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-40 T1 CAS Channel Status for Cisco Unified Communications Manager-Controlled MGCP Gateway
Counters
|
Description
|
DS1 Name
|
DS1 name.
|
Channel Status [n]
Note Displayed for each of 24 channels with n from 0 through 23.
|
200=idle, 300=unknown, 301=other, 302=voice, 303=unrestrictedDigital, 304=unrestrictedDigital56, 305=restrictedDigital, 306=audio31, 307=audio7, 308=video, 309=packetSwitched, 310=fax, 312=unknown, 313=analog, 314=digital, 315=v110, 316=v120
|
T1 CAS Channel Status for IOS GW
The set of performance counters in Table A-41 is displayed for each T1 CAS port in the Cisco IOS gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
.
Table A-41 T1 CAS Channel Status for Cisco IOS Gateway
Counters
|
Description
|
DS1 Name
|
DS1 name
|
Channel Status [n]
Note Displayed for each of 24 channels with n from 0 through 23.
|
200=idle, 300=unknown, 301=other, 302=voice, 303=unrestrictedDigital, 304=unrestrictedDigital56, 305=restrictedDigital, 306=audio31, 307=audio7, 308=video, 309=packetSwitched, 310=fax, 312=unknown, 313=analog, 314=digital, 315=v110, 316=v120
|
T1 CAS Usage for CCM GW
The set of performance counters in Table A-42 is displayed for each T1 CAS in the Cisco Unified Communications Manager-controlled MGCP gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-42 T1 CAS Usage for Cisco Unified Communications Manager-Controlled MGCP Gateway
Counters
|
Description
|
CCM Name
|
Cisco Unified Communications Manager that the MGCP gateway is registered with
|
DS1 Name
|
Name of DS1
|
Calls Completed
|
Number of calls completed on this T1 CAS port on the gateway
|
Outbound Busy Attempts
|
Number of outbound busy attempts on this T1 CAS port on the gateway
|
T1 PRI Channel Status for CCM GW
The set of performance counters in Table A-43 is displayed for each T1 PRI port in the Cisco Unified Communications Manager-controlled MGCP gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-43 T1 PRI Channel Status for Cisco Unified Communications Manager-Controlled MGCP Gateway
Counters
|
Description
|
DS1 Name
|
DS1 name
|
Channel Status [n]
Note Displayed for each of 24 channels with n from 0 through 23.
|
0=unknown, 1=out-of-service, 2=idle, 3=busy, 4=reserved
|
T1 PRI Channel Status for IOS GW
The set of performance counters in Table A-44 is displayed for each T1 PRI port in the Cisco IOS gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-44 T1 PRI Channel Status for Cisco IOS Gateway
Counters
|
Description
|
DS1 Name
|
DS1 name
|
Channel Status [n]
Note Displayed for each of 24 channels with n from 0 through 23.
|
200=idle, 300=unknown, 301=other, 302=voice, 303=unrestrictedDigital, 304=unrestrictedDigital56, 305=restrictedDigital, 306=audio31, 307=audio7, 308=video, 309=packetSwitched, 310=fax, 312=unknown, 313=analog, 314=digital, 315=v110, 316=v120
|
T1 PRI Usage for CCM GW
The set of performance counters in Table A-45 is displayed for each T1 PRI in the Cisco Unified Communications Manager-controlled MGCP gateway.
Note Polling for these counters is disabled by default and is controlled by Voice Utilization Settings.
Table A-45 T1 PRI Usage for Cisco Unified Communications Manager-Controlled MGCP Gateway
Counters
|
Description
|
CCM Name
|
Cisco Unified Communications Manager that the MGCP gateway is registered with.
|
DS1 Name
|
Name of DS1.
|
Calls Completed
|
Number of calls completed on this T1 PRI port on the gateway.
|
Outbound Busy Attempts
|
Number of outbound busy attempts on this T1 PRI port on the gateway.
|
