Table B-1 Ctm_Config_Table Parameters
Parameter Name
|
Definition
|
transportManager
|
jmoco-port
|
Port where JMOCO events are sent.
|
main-error-level
|
Error levels supported in CTM. Values are trace, debug, minor, major, critical.
|
min-alarm-update-interval
|
Minimum time, in seconds, when an active_alarm_update event is sent.
|
ems-sys-id
|
System ID indicating who sent the event (for example, if the event is generated by the EMS, the system ID is CTM).
|
preferred-jar-path
|
Path to obtain Cisco Transport Controller (CTC) jar files.
|
preferred-jar-version
|
Version of the CTC jar that needs to be picked.
|
tl1-connection-timeout
|
Timeout period if a TL1 connection has not been used.
|
jmoco-trace-frequency
|
(Not used)
|
jmoco-max-user-sessions
|
Maximum number of sessions a jmoco engine can support.
|
oss-thread-count
|
Maximum number of threads that can be spawned in CTM.
|
oss-work-queue-threshold
|
Maximum number of work objects that can be added into the work queue.
|
oss-max-threads
|
Maximum number of threads that can be read from the work queue.
|
oss-jmoco-threads
|
Number of threads used to read events from the work queue.
|
oss-jmoco-event-threads
|
Number of threads used to distribute events from the work queue to registered users.
|
oss-socket-send-size
|
Maximum size of the buffer that the socket can support to send.
|
oss-socket-recv-size
|
Maximum size of the buffer that the socket can support to receive.
|
refresh-data-timeout
|
Specifies the Refresh Data Timer interval, in milliseconds. When a discovery change event is received, the Refresh Data Timer is started. The timer records the number of NEs in synch status. When the timer expires, it retrieves the number of NEs in synch and compares this value to the recorded one. If the values are equal, it forces a Refresh Data action.
|
gatewayTL1
|
gwTL1ForwardingAgent
|
Whether CTM GateWay/TL1 is installed, stopped, or started.
|
response-parameters
|
(Not used)
|
ne-name
|
alarm-logic
|
in-progress-frequency
|
oss-mux
|
oss-pt
|
load-db-nes
|
deny-act-user
|
oss-port
|
CTM GateWay/TL1 port.
|
15454-vasco-tl1-port
|
Vasco TL1 port for the ONS 15454.
|
15454-tl1-port
|
TL1 port.
|
15327-tl1-port
|
15800-tl1-port
|
15801-tl1-port
|
15808-tl1-port
|
15216-oadm2-tl1-port
|
15216-edfa-tl1-port
|
15310-tl1-port
|
15454SDH-tl1-port
|
15216-edfa3-tl1-port
|
15600-tl1-port
|
15600-tl1-telnet-port
|
(Not used)
|
15501-tl1-port
|
TL1 port.
|
15530-tl1-port
|
15540-esp-tl1-port
|
15540-espx-tl1-port
|
poll-frequency
|
Time, in seconds, that CTM GateWay/TL1 checks the status of the NE.
|
error-level
|
Debug level for the CTM GateWay/TL1 service module.
|
gwTL1Timeout
|
Time, in seconds, before CTM GateWay/TL1 times out.
|
gwTL1LoginTimeout
|
Enables or disables the CTM GateWay/TL1 timeout period if the ACT-USER command is not performed before the timeout period.
|
gwTL1CmdTimeout
|
Enables or disables the CTM GateWay/TL1 timeout period if a valid TL1 command is not performed before the timeout period.
|
gwTL1Connections
|
Number of TL1 connections to CTM GateWay/TL1.
|
enable-gwtl1-advisory
|
Enables or disables display of advisory messages.
|
gwtl1-advisory-message
|
CTM GateWay/TL1 advisory message. The default message reads "NOTICE: This is a private computer system. Unauthorized access or use may lead to prosecution."
|
command-echo
|
Allows you to view the command line when you enter commands during a GateWay/TL1 session. This also allows you to log all messages received during a GateWay/TL1 session. The default is false, meaning that GateWay/TL1 session echoing is disabled.
|
gatewaySNMP
|
gatewaySNMP
|
Whether CTM GateWay/SNMP is installed, stopped, or started.
|
snmp-hosts
|
SNMP trap destination hosts.
|
gatewayCORBA
|
gatewayCORBA
|
Whether CTM GateWay/CORBA is installed, stopped, or started.
|
corba-request-timeout
|
CORBA timeout value.
|
thread-pool-size
|
Thread pool size used in the CORBA gateway.
|
iiop-listen-port
|
CORBA gateway listening port.
|
error-level
|
Debug level for CTM GateWay/CORBA.
|
heartbeat-interval
|
Interval, in minutes, for the heartbeat event.
|
enable-gwcorba-encryption
|
Whether the CORBA gateway encryption feature is enabled or disabled.
|
max-number-active-sessions
|
Specifies the number of CTM GateWay/CORBA sessions that can be active at the same time. The range is from 4 to 25; the default is 4.
|
max-events_per_consumers
|
Sets the MaxEventsPerConsumer administrative quality of service (QoS) parameter on the notification channel. The notification server uses this property to limit the maximum number of events in a given channel allowed to queue at any one time. The default value is 0, meaning that the notification server does not limit the maximum number of events that can be queued. If no limits are imposed on the queue, the notification server might run out of memory, because the server must keep all events in memory until they are consumed by all registered consumers.
Caution  Any change to this value should be done with extreme caution. If you set the value too low, the NMS cannot receive all notifications. If you set the value too high, the CTM notification server runs out of memory. The current value can handle alarm bursts of 10,000 events per minute.
|
notification_service_name
|
Defines the service name used by the resolve_initial_reference function to get a reference to the notification service.
The CTM GateWay/CORBA installation installs the notification service. However, if you want to use your own notification service, you can modify this parameter.
|
notification_service_naming_context
|
Defines the naming context of the notification service. This property is used when the resolve_initial_reference function fails to resolve the notification service. CTM GateWay/CORBA contacts the naming service to resolve the name context defined in this property. The value of this property must match the value published by your notification server.
|
notification_service_factory_ior_name
|
Sets the notification service factory Information Object Repository (IOR) filename located in the /opt/CiscoTransportManagerServer/openfusion/domains/OpenFusion/localhost/NotificationService/NotificationSingleton/NotificationService.ior directory.
The FactoryIORFile property defines the path to a text file that contains the IOR of the notification service. This property is used only after the resolve_initial_reference function and the naming service both fail. CTM GateWay/CORBA opens the file as defined by the URL format in this property and retrieves the IOR. This parameter allows you to run your notification service on a different host to improve performance.
|
notification_service_port_number
|
Sets the port number that the notification service uses to listen for incoming requests. The port number is set in the IOR for the notification service. The use IOR and use IOR endpoint properties are set properly. If set to 0 (the default), the port number is allocated by the operating system.
|
session_port_number
|
Configures the IIOP listening port. The CTM GateWay/CORBA service listens to CORBA requests on this port. If set to 0 (the default), the session port number is allocated by the operating system.
|
name_service_server_list
|
Defines where the name servers are running. Accepts a comma-separated list of hostnames.
|
name_service_root_ior
|
Defines the path to find the naming service's IOR on each host defined on the server list. The complete path is constructed as <http://<item>_of_ServerList><RootIORLoc>.
|
ne
|
poll-frequency
|
Wait duration for the next health poll to start.
|
corba-request-timeout
|
CORBA timeout value.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ne-discov-thread-pool-size
|
Number of threads that are available for initial poll, alarm resync, and config resync.
|
snmp-trap-thread-pool-size
|
Number of threads that are available for the SNMP trap event converter.
|
alarm-thread-pool-size
|
Number of threads that are available for the alarm dispatcher.
|
ne-circuit-discovery-thread-pool-size
|
Number of threads that are available for circuit discovery.
|
pm
|
number-of-collectors
|
Number of threads that are available for the collector thread pool. This thread pool is used to poll the NEs and obtain performance statistics.
|
number-of-writers
|
Number of threads that are available for the database writer thread pool. This thread pool is used to write performance statistics in the database.
|
number-of-nes
|
(Not used)
|
store-non-zeros-only
|
Runs PM data collection in optimized mode. If the performance counts are zero, this parameter controls whether or not it should be written to the database.
|
pm-disk-limit
|
(Not used)
|
pm-jvm-heap-init
|
Initial heap size for the PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for the PM service process.
|
pm-15-min-retrieval-enabled
|
Controls PM alarm generation. When enabled and PM collection fails for a 15-minute interval, a PM alarm is emitted.
|
pm-15-min-retrieval-secs-between-
retries
|
Number of seconds to wait before CTM retries and polls the NE. Used when PM collection fails in normal mode for a 15-minute interval.
|
pm-15-min-retrieval-number-of-retries
|
Number of times CTM should retry and poll the NEs. Used when PM collection fails in normal mode for a 15-minute interval.
|
pm-1-day-retrieval-enabled
|
Controls PM alarm generation. When enabled and PM collection fails for a one-day interval, a PM alarm is emitted.
|
pm-1-day-retrieval-secs-between-
retries
|
Number of times CTM should retry and poll the NEs. Used when PM collection fails in normal mode for a one-day interval.
|
pm-1-day-retrieval-number-of-retries
|
Number of times CTM should retry and poll the NEs. Used when PM collection fails in normal mode for a one-day interval.
|
max-realtime-sessions
|
Maximum number of concurrent real-time PM sessions allowed per client.
|
max-realtime-objects
|
Maximum number of objects that can be polled in a single real-time PM session.
|
max-realtime-rows
|
Maximum number of rows that are held in the real-time in-memory transient buffer on a per-session basis. Once this limit is reached, the buffer rolls over, meaning that the chronologically oldest rows are removed from the buffer, making room for the new rows.
|
cm
|
config-vlan-thread-count
|
Number of threads that are available for VLAN discovery.
|
config-vlan-autosync-delay
|
Delay after which time the topologies and VLANs are synchronized with the NE.
|
bandwidth-util-dsp
|
In the Control Panel window > SONET/SDH NE Service pane, check the Enable Bandwidth DSP check box to enable the check for available bandwidth during VLAN creation. If you create a VLAN that could cause oversubscription of the available bandwidth for the L2 topology, and if the Enable Bandwidth DSP check box is checked, you receive an error message that oversubscription might occur. The check box is disabled by default.
|
bandwidth-util-dsp-sdh
|
In the Control Panel window > SONET/SDH NE Service pane, check the Enable Bandwidth DSP check box to enable the check for available bandwidth during VLAN creation. If you create a VLAN that could cause oversubscription of the available bandwidth for the L2 topology, and if the Enable Bandwidth DSP check box is checked, you receive an error message that oversubscription might occur. The check box is disabled by default.
|
config-dsp-max-idle-time
|
Set to check if sufficient time has passed from the last event received and all topology audits have been completed.
|
config-dsp-msync-wait-time
|
Time to wait until the set time for Node Manager Sync to be completed.
|
config-max-partial-topo-time
|
Time to schedule a task to scan and mark all partial topologies as incomplete.
|
config-sync-thread-run-delay
|
Frequency of tasks that check if the data service module is ready for provisioning (data provisioning ready state).
|
config-topo-incomplete-thread-run-
delay
|
Time to schedule a task to declare the incomplete topologies.
|
dsp-debug-telnet-port
|
Telnet port to turn on the DataService.log for debugging topology discovery-related information.
|
config-resync-thread-pool-size
|
(Not used)
|
config-poll-frequency
|
Polling period to check if the config resync time has been reached.
|
config-resync-frequency
|
Periodic frequency at which the config resync is performed.
|
config-request-queue-size
|
(Not used)
|
iiop-listen-port
|
(Not used)
|
backup-frequency
|
Frequency at which the backup should be performed (for example, daily, weekly, or just once).
|
backup-copies-ons15454
|
Number of copies of backed-up configuration and provisioning information residing in the flash memory of the NEs.
|
backup-copies-ons15800
|
backup-copies-ons15327
|
backup-copies-ons15540
|
backup-copies-ons15454sdh
|
backup-copies-ons15600
|
backup-copies-ons15600sdh
|
backup-copies-ons15530
|
backup-copies-ons15540xps
|
backup-copies-ons15216edfa
|
backup-copies-hfr
|
backup-copies-gsriox
|
backup-copies-ons15310cl
|
backup-copies-ons15216edfa3
|
backup-copies-mgx8880
|
backup-copies-ons15305ctc
|
(Not used)
|
backup-status-ons15454
|
Current status of the task: Queued, Running, Canceled, Failed, Succeeded, or Waiting.
|
backup-status-ons15800
|
backup-status-ons15327
|
backup-status-ons15540
|
backup-status-ons15540xps
|
backup-status-ons15530
|
backup-status-ons15454sdh
|
backup-status-ons15600
|
backup-status-ons15600sdh
|
backup-status-ons15216edfa
|
backup-status-hfr
|
backup-status-gsriox
|
backup-status-ons15310cl
|
backup-status-ons15216edfa3
|
backup-status-mgx8880
|
backup-status-ons15305ctc
|
(Not used)
|
backup-time-ons15454
|
Time for the NE configuration backup.
|
backup-time-ons15800
|
backup-time-ons15327
|
backup-time-ons15540
|
backup-time-ons15454sdh
|
backup-time-ons15600
|
backup-time-ons15600sdh
|
backup-time-ons15530
|
backup-time-ons15540xps
|
backup-time-ons15216edfa
|
backup-time-hfr
|
backup-time-gsriox
|
backup-time-ons15310cl
|
backup-time-ons15216edfa3
|
backup-time-mgx8880
|
backup-time-ons15305ctc
|
(Not used)
|
manual_backup-copies-ons15454
|
Number of copies that can be backed up manually. Each NE backup is performed by selecting the Configuration > Memory Backup > User Specified radio button.
|
manual_backup-copies-ons15800
|
manual_backup-copies-ons15327
|
manual_backup-copies-ons15540
|
manual_backup-copies-ons15454sdh
|
manual_backup-copies-ons15600
|
manual_backup-copies-ons15600sdh
|
manual_backup-copies-ons15530
|
manual_backup-copies-ons15540xps
|
manual_backup-copies-ons15216edfa
|
manual_backup-copies-ons15216edfa3
|
manual_backup-copies
|
manual_backup-copies-hfr
|
manual_backup-copies-gsriox
|
manual_backup-copies-ons15310cl
|
manual_backup-copies-mgx8880
|
manual_backup-copies-ons15305ctc
|
(Not used)
|
backup-directory
|
Name of the link to the source directory on the server for backup file upload operations. This name appears in the /opt/CiscoTransportManagerServer/webServer/htdocs folder. For example, if the /htdocs folder contains the link "admin -> /opt/CiscoTransportManagerServer/admin," admin is the value of the backup-directory property.
|
archive-dest-dir
|
Destination directory on the client for archiving upload operations. The client installation path is the default path. For example, if the complete path for the archiving directory is C:/TransportManagerClient/archive, the value of the archive-dest-dir property is archive. The default value for this property is log.
|
archive-source-link-name
|
Name of the link to the source directory on the server for archiving upload operations. This name appears in the /opt/CiscoTransportManagerServer/webServer/htdocs folder. For example, if the /htdocs folder contains the link "archive -> /opt/CiscoTransportManagerServer/log," archive is the value of the archive-source-link-name property. When you change the server source directory, the name of the link does not change.
|
log-source-link-name
|
Name of the link to the source directory on the server for log file upload operations. This name appears in the /opt/CiscoTransportManagerServer/webServer/htdocs folder. For example, if the /htdocs folder contains the link "log -> /opt/CiscoTransportManagerServer/log," log is the value of the log-source-link-name property. When you change the server source directory, the name of the link does not change.
|
alarm-data
|
Parameters used for CTC-based automatic backup.
|
pm-data
|
auditlog-data
|
manual-alarm-data
|
(Not used)
|
manual-pm-data
|
(Not used)
|
manual-auditlog-data
|
(Not used)
|
auto-job-thread-pool-size
|
Number of threads used to read the automatic jobs from the work queue. The default is 10.
|
manual-job-thread-pool-size
|
Number of threads used to read the manual jobs from the work queue. The default is 10.
|
snmp
|
snmpTrapService
|
Enables or disables the SNMP trap service upon CTM server startup. The default is enabled.
|
snmp-trap-queue-size
|
Maximum number of traps that can be queued in the SNMP trap service before being distributed to NE services. When the queue reaches its maximum, incoming traps are dropped. The default is 10000.
|
snmp-trap-drop-size
|
Threshold to drop incoming traps. The default is 100.
|
snmp-trap-forwarding-port
|
SNMP gateway trap port. The default is 8765.
|
snmp-trap-port
|
Incoming trap port. The default is 162.
|
snmp-mibs-dir
|
MIB file directory. The default is /mibs.
|
st-error-level
|
Debug log level. The default is minor.
|
serviceManager
|
sm-jvm-heap-init
|
Initial heap size allocated to the SM service.
|
sm-jvm-heap-max
|
Maximum heap size allocated to the SM service.
|
sm-error-level
|
Error level for the process. Values are debug, trace, minor, major, or critical.
|
service-stop-timer
|
Time interval for which the SM service waits for the service to stop.
|
diskspace-poll-period
|
(Not used)
|
hello-poll-interval
|
Poll interval at which the hello operation is performed on an NE.
|
hello-stop-timer
|
Time interval for which the SM service waits for the service to shut down gracefully.
|
hello-kill-timer
|
Time interval after which the SM service forcibly kills the service when it does not respond.
|
ons15200-ne
|
ne-service
|
(Not used)
|
ne-threshold
|
(Not used)
|
ne-error-level
|
(Not used)
|
ne-resync-frequency
|
(Not used)
|
ne-thread-pool-size
|
(Not used)
|
ne-jvm-heap-init
|
(Not used)
|
ne-jvm-heap-max
|
(Not used)
|
ons15216-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 1000.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_service_name > Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
ons15327-ne
|
fault-sync
|
Enables or disables historical alarm collection.
|
ons15600-ne
|
fault-sync
|
Enables or disables historical alarm collection.
|
ons15600sdh-ne
|
fault-sync
|
Enables or disables historical alarm collection.
|
ons15454-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-low-threshold
|
Threshold value for the maximum number of NEs that can be discovered.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 500.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_service_name > Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ne-ios-cr-thread-pool-size
|
Number of threads in a pool where each thread is used to process Cisco IOS configuration resync updates. The default is 10.
|
ne-ios-updates-cr-frequency
|
Number of seconds when Cisco IOS configuration resync updates are processed. The default is 60.
|
audit-trail-collection-interval
|
Wait duration for the next audit trail collection to start.
|
audit-trail-thread-count
|
Number of threads that can be used to collect the audit trail.
|
fault-sync
|
Enables or disables historical alarm collection.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
blsr-interval
|
Difference in interval between east and west port job execution.
|
client-list-thread-pool-size
|
Number of threads in a pool where each thread is used to poll the ENE client list from the gateway NE (that is, the GNE with proxy turned on). The default is 20.
|
ctm-event-disp-thread-count
|
Number of threads that are available for dispatching events.
|
ctm-invupd-thread-count
|
Number of threads that are available to handle inventory updates.
|
client-list-poll-frequency
|
Interval at which the list of ENEs for all the GNEs in the domain is collected. The Proxy_Server_Table is modified with the changes and the GNE, ENE, and LNE changes are reflected in the Domain Explorer.
|
ons15454sdh-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-low-threshold
|
Threshold value for the maximum number of NEs that can be discovered.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 600.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_service_name > Config Resync Interval.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ne-ios-cr-thread-pool-size
|
Number of threads in a pool where each thread used to process Cisco IOS configuration resync updates. The default is 10.
|
ne-ios-updates-cr-frequency
|
Number of seconds when Cisco IOS config resync updates are processed. The default is 60.
|
audit-trail-collection-interval
|
Wait duration for the next audit trail collection to start.
|
audit-trail-thread-count
|
Number of threads that can be used to collect the audit trail.
|
fault-sync
|
Enables or disables historical alarm collection.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
mspring-interval
|
Difference in interval between east and west port job execution.
|
client-list-poll-frequency
|
Interval at which the list of ENEs for all the GNEs in the domain is collected. The Proxy_Server_Table is modified with the changes and the GNE, ENE, and LNE changes are reflected in the Domain Explorer.
|
ons155xx-ne
|
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 1000.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-resync-frequency
|
Periodic frequency at which the configuration resynchronization is performed. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_service_name > Config Resync Interval.
|
discovery-threads-pool-size
|
Number of discovery threads that are available for discovering ONS 155xx NEs.
|
discovery-threads-p1
|
Number of threads used by the ONS 155xx NE service for 155xx device discovery, including inventory and alarms.
|
discovery-threads-p2
|
Number of threads used by the ONS 155xx NE service for topology and circuit discovery.
|
discovery-wait-on-ne-create
|
Wait time, in seconds, after an ONS 155xx NE has been added to the network.
|
discovery-enable-cdp
|
Enables or disables discovery of configured CDP neighbors.
|
discovery-auto-neighbor
|
Enables or disables discovery of configured non-CDP neighbors.
|
discovery-auto-delete-stale-links
|
Enables or disables automatic deletion of stale links from the database.
|
tftp-timeout
|
Timeout period for any TFTP operations to and from the ONS 155xx and the server.
|
backup-config-before-restore
|
Enables or disables backup of the NE configuration before restoring the new configuration.
|
snmp-pdu-maxvars
|
Size of the SNMP PDU varbinds used while creating a connection with the NE.
|
EntityAlarmsToIgnore
|
Indicates whether there are any ONS 155xx entity alarms to be ignored.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
discovery-fast-mode
|
Enables or disables discovery of ONS 155xx NEs in fast mode.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
ons15800-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 1000.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-resync-frequency
|
Periodic frequency at which the configuration resynchronization is performed. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_service_name > Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
ons15801-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 1000.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-resync-frequency
|
Periodic frequency at which the configuration resynchronization is performed. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_service_name > Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
ons15808-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 1000.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-resync-frequency
|
Periodic frequency at which the configuration resynchronization is performed. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_service_name > Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
hfr-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 1000.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
gsriox-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 1000.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
cat65xx-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 1000.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ons15302-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 1000.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-resync-frequency
|
Periodic frequency at which the configuration resynchronization is performed. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_service_name > Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
ne-sntp-default-sync-time
|
Default value used for the resync time.
|
ons15305-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 1000.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-resync-frequency
|
Periodic frequency at which the configuration resynchronization is performed. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_service_name > Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads that are available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
ne-sntp-default-sync-time
|
Value used for the resync time. The default is 30.
|
ons15310-ne
|
fault-sync
|
Enables or disables historical alarm collection.
|
unmanaged-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 500.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
mgx88xx-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 400.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
num-ooemc
|
Number of Object Oriented Equipment Manager Client (ooemc) process instances that need to be started by the MGX Voice Gateway NE service. This process name is visible on the server by entering the showctm -v command.
|
mds9000-ne
|
ne-service
|
The NE service process starts automatically whenever at least one NE is added to the CTM domain. If no NEs are present, this service does not run. If it ran previously, this service terminates as soon as no NEs are in the domain.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. This value can be modified from the CTM client through Administration > Control Panel > NE Service > NE_name > Error Level.
|
ne-threshold
|
Maximum number of NEs that can be handled. The default is 500.
|
ne-jvm-heap-init
|
Initial heap size for the NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for the NE service process.
|
ons15454-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 700.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
pm-http-retries
|
(Not used)
|
pm-wait-period
|
pm-interface-ds1
|
Enables or disables performance statistics collection.
|
pm-interface-ds3
|
pm-interface-sonet
|
pm-interface-sts
|
pm-interface-vt
|
pm-interface-enet
|
Enables or disables Ethernet performance statistics collection.
|
pm-interface-physical
|
Enables or disables the physical performance statistics collection for optical cards.
|
pm-interface-dwdm
|
Enables or disables OTN section, line, and path performance statistics collection for DWDM cards.
|
pm-interface-E1
|
Enables or disables performance statistics collection for E1 cards.
|
pm-snmp
|
Enables or disables SNMP performance monitoring for cards on the ONS 15454 SONET.
|
pm-jvm-heap-init
|
Initial heap size for the PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for the PM service process.
|
ons15454sdh-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 1000.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
pm-http-retries
|
(Not used)
|
pm-wait-period
|
pm-interface-E1
|
Enables or disables performance statistics collection.
|
pm-interface-E3
|
pm-interface-E4
|
pm-interface-ds1
|
pm-interface-ds3I
|
pm-interface-sdh
|
pm-interface-HO
|
pm-interface-LO
|
pm-interface-enet
|
Enables or disables Ethernet performance statistics collection.
|
pm-interface-physical
|
Enables or disables physical performance statistics collection for optical cards.
|
pm-interface-dwdm-sdh
|
Enables or disables OTN section, line, and path performance statistics collection for DWDM cards.
|
pm-snmp
|
Enables or disables SNMP performance monitoring for cards on the ONS 15454 SDH.
|
pm-jvm-heap-init
|
Initial heap size for the PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for the PM service process.
|
ons15600-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 1000.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
pm-http-retries
|
(Not used)
|
pm-wait-period
|
(Not used)
|
pm-interface-sonet
|
Enables or disables SONET section and line performance statistics collection.
|
pm-interface-sts
|
Enables or disables SONET STS path performance statistics collection.
|
pm-interface-enet
|
Enables or disables Ethernet performance statistics collection.
|
pm-jvm-heap-init
|
Initial heap size for the PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for the PM service process.
|
ons15600sdh-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 1000.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
pm-http-retries
|
(Not used)
|
pm-wait-period
|
(Not used)
|
pm-interface-sdh
|
Enables or disables SDH performance statistics collection.
|
pm-interface-HO
|
Enables or disables higher-order (HO) path performance statistics collection.
|
pm-jvm-heap-init
|
Initial heap size for the PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for the PM service process.
|
ons155xx-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 1000.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
pm-poll-delay
|
Indicates the delay time, in seconds, for 15-minute and 24-hour PM collections to start. The default is 90 seconds.
|
pm-jvm-heap-init
|
Initial heap size for the PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for the PM service process.
|
ons158xx-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 1000.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
pm-15m-delay
|
Time, in seconds, to wait after the quarter is exceeded before collecting PM data.
|
pm-24h-delay
|
Time, in seconds, to wait after the 24 hours are exceeded before collecting PM data.
|
pm-jvm-heap-init
|
Initial heap size for the PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for the PM service process.
|
ons15216-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 1000.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
pm-jvm-heap-init
|
Initial heap size for the PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for the PM service process.
|
ons1530x-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 1000.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
pm-15m-delay
|
Time, in seconds, to wait after the quarter is exceeded before collecting PM data.
|
pm-24h-delay
|
Time, in seconds, to wait after the 24 hours are exceeded before collecting PM data.
|
pm-jvm-heap-init
|
Initial heap size for the PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for the PM service process.
|
mgx88xx-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 700.
|
pm-error-level
|
PM service error log level. By default, trace severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
hfr-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 1000.
|
pm-error-level
|
PM service error log level. By default, debug severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
gsriox-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 1000.
|
pm-error-level
|
PM service error log level. By default, debug severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
cat65xx-pm
|
pm-service
|
Possible values are active or not-active. The default value is not-active. If the value of the property is active, the corresponding PM service will be started when PM data collection is enabled on the NE(s). The value of this property should be set to active to collect PM data on NEs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_type.
|
pm-threshold
|
Maximum number of NEs managed by the PM service process. The default is 1000.
|
pm-error-level
|
PM service error log level. By default, debug severity log messages are entered in the PM service logs. This value can be modified from the CTM client through Administration > Control Panel > PM Service > NE_name > Error Level.
|
security
|
password-reuse-count
|
Number of previously used passwords to compare against the new password. The range is from 0 to 5 passwords; the default is 5 passwords. A value of 0 disables this feature.
|
password-change-interval
|
Number of days a user must wait between password changes. The range is from 0 to 99 days; the default is 20 days. A value of 0 disables this feature.
|
password-differ-limit
|
Number of characters by which the new password must differ from the previous one. The range is from 1 to 5 characters; the default is 3 characters.
|
password-age
|
Sets the password aging interval to any interval between 0 and 999 days. You are prompted to change the password after the specified number of days. The default is 30 days.
|
password-notification-enabled
|
Sets an early warning period for password expiration. CTM supports values of 0 to (password aging - 1), with a maximum of 30. For example, if the password aging is configured for 30 days, the maximum early notification value would be 29 days. A value of 0 disables this feature.
|
password-notification-interval
|
Sets the number of days before the warning for password expiration. The default is 0.
|
max-unsuccessful-attempts
|
Sets the maximum number of attempts a user is allowed to log in before being locked out for the length of time specified in the Lockout Time field. The allowable range is from 0 to 10 retries; the default is 5 retries.
|
min-password-length
|
Minimum password length. The range is from 2 to 10 characters; the default is 6 characters.
|
max-password-length
|
Maximum password length. The range is from 10 to 12 characters; the default is 12 characters.
|
num-alpha-chars
|
Minimum number of alphabetic characters that the password must include. The range is from 0 to 2; the default is 2 alphabetic characters.
|
num-locase-alpha-chars
|
Minimum number of lowercase alphabetic characters that the password must include. The range is from 0 to 2; the default is 1 lowercase character.
|
num-upcase-alpha-chars
|
Minimum number of uppercase alphabetic characters that the password must include. The range is from 0 to 2; the default is 1 uppercase character.
|
num-numeric-chars
|
Minimum number of numeric characters that the password must include. The range is from 0 to 2; the default is 1 numeric character.
|
num-special-chars
|
Minimum number of special characters that the password must include. The range is from 0 to 2; the default is 1 special character.
|
allow-numeric-firstlast
|
Specifies whether a numeric character is allowed as the first or last character in the password. The default is true; the first or last character in the password can be a number.
|
allow-special-firstlast
|
Specifies whether a special character is allowed as the first or last character in the password. The default is true; the first or last character in the password can be a special character.
|
allow-circular-shift
|
Specifies whether the user ID or a circular shift of the ID can be used in the password. The default is false; the user ID or a circular shift of the ID cannot be used in the password.
|
special-char-set
|
Special character set to use. The default is TL1+UNIX.
|
lockout-period
|
Sets the number of minutes a user's CTM session is inactive before CTM automatically locks the user out. The allowable range is from 0 to 120 minutes in 1-minute increments; the default is 30 minutes. A value of 0 disables this feature.
|
client-lockout
|
Enables or disables client lockout.
|
client-lockout-period
|
Sets the number of minutes a user's CTM session is inactive before CTM automatically logs the user out. The allowable range is from 0 to 1440 minutes in 1-minute increments. A value of 0 disables this feature.
|
client-logout
|
Enables or disables client logout.
|
client-logout-period
|
Sets the number of minutes a user's CTM session is inactive before CTM automatically logs the user out. The allowable range is from 0 to 1440 minutes in 1-minute increments. A value of 0 disables this feature.
|
security-advisory-message
|
(This parameter is not applicable to ONS 155xx NEs.) If checked, the advisory message that appears on login is enabled.
|
ons158xxusername
|
Usernames and passwords used to connect to a specific NE.
|
ons158xxpassword
|
ons158xxGWTL1username
|
ons158xxGWTL1password
|
ons1530xusername
|
ons1530xpassword
|
ons1530xGWTL1username
|
ons1530xGWTL1password
|
ons15454username
|
ons15454password
|
ons15454GWTL1username
|
ons15454GWTL1password
|
ons15454MLSeriesusername
|
ons15454MLSeriespassword
|
ons15327username
|
ons15327password
|
ons15327GWTL1username
|
ons15327GWTL1password
|
ons15454SDHusername
|
ons15454SDHpassword
|
ons15454SDHGWTL1username
|
ons15454SDHGWTL1password
|
ons15454SDHMLSeriesusername
|
ons15454SDHMLSeriespassword
|
ons15216EDFA2username
|
Usernames and passwords used to connect to a specific NE.
|
ons15216EDFA2password
|
ons15216EDFA3username
|
ons15216EDFA3password
|
ons15216OADMUserName
|
ons15216OADMUserPass
|
ons15216OADMGWTL1UserName
|
ons15216OADMGWTL1UserPass
|
ons15216EDFAGWTL1UserName
|
ons15216EDFAGWTL1UserPass
|
ons15216EDFAUserName
|
Usernames and passwords used to connect to a specific NE.
|
ons15216EDFAUserPass
|
ons15216EDFA3GWTL1UserName
|
ons15216EDFA3GWTL1UserPass
|
ons15216EDFA3FtpDir
|
ons15216EDFA3FtpUserName
|
ons15216EDFA3FtpUserPass
|
ons15305ctcusername
|
(Not used)
|
ons15305ctcpassword
|
(Not used)
|
ons155xxusername
|
(Not used)
|
ons155xxpassword
|
(Not used)
|
ons155xxGWTL1username
|
Username and password used to connect to the ONS 155xx GateWay/TL1 NE.
|
ons155xxGWTL1password
|
telnet-password
|
Telnet password.
|
ne-global-user-name
|
NE global username.
|
ne-global-user-password
|
NE global password.
|
ons15600username
|
Usernames and passwords used to connect to a specific NE.
|
ons15600password
|
ons15600GWTL1username
|
ons15600GWTL1password
|
ons15600SDHusername
|
ons15600SDHpassword
|
ons15600SDHGWTL1username
|
ons15600SDHGWTL1password
|
ons15310CLusername
|
ons15310CLpassword
|
ons15310CLGWTL1username
|
ons15310CLGWTL1password
|
ons15310CLMLSeriesusername
|
ons15310CLMLSeriespassword
|
hfrusername
|
Usernames and passwords used to connect to a specific NE.
|
hfrpassword
|
gsrioxusername
|
gsrioxpassword
|
mds9000CLIusername
|
mds9000CLIpassword
|
mds9000readcommstr
|
SNMP read community string for the MDS 9000 NE. The default is public.
|
mds9000writecommstr
|
SNMP write community string for the MDS 9000 NE.
|
ui
|
overwrite-alarm-notes
|
Enables or disables the ability to overwrite alarm notes created by another user.
|
overwrite-circuit-notes
|
Enables or disables the ability to overwrite circuit notes created by another user.
|
overwrite-job-notes
|
Enables or disables the ability to overwrite job notes created by another user.
|
unack-alarm
|
Enables or disables the ability to unacknowledged alarms that have been acknowledged.
|
ne-name-truncation
|
Allows you to specify how node names longer than 25 characters are truncated in the Network Map. If a string is longer than 25 characters, the first 22 characters display followed by an ellipsis (...). You can choose to truncate the first or last characters of the node name.
|
ne-no-topo-hosts
|
Allows you to manage the number of CTC instances for optimal CTC performance. The Cisco default is 10 CTC-based NEs. Although CTM can support up to 2,500 CTC-based NEs, CTC cannot effectively manage more than a small subset of these NEs. Consequently, the CTM domain must be partitioned into smaller CTC domains with one instance of CTC launched per CTC domain. The specified number of CTC-based NEs determines the number of GNEs, or topology hosts, that constitute each CTC management domain. CTC uses the GNEs provided to discover and display other nodes that are physically connected to the GNEs. For example, if each CTC-based NE ring contains three NEs (including the GNE), CTC discovers and manages 3 x 10 = 30 nodes when the value is set to 10. In environments where most CTC-based NE rings or subnetworks contain 10 to 16 NEs, set this number to a smaller value, such as 3.
|
clear-unack-alarms
|
(Not used)
|
subnetwork-auto-grouping
|
Enables or disables the ability to automatically group NEs in subnetworks.
|
enable-port-state-coloring
|
When port state coloring is enabled, the NE Explorer shelf views and card-level views report the port and alarm status as a background color.
|
default-audit-trail-state
|
Enables or disables the audit trail. NEs that are added or discovered will be assigned this setting.
|
ne
|
debug-telnet-port
|
(Not used)
|
debug
|
logging-option
|
Enables the ability to change the logging library. Values are JDK, Log4j, and VW debug.
|
log-buf-size
|
Maximum buffer size when logging is done using JDK or Log4j.
|
vwdebug-log-buf-size
|
Maximum buffer size when logging is done using VW debug.
|
vwdebug-log-idle-time
|
Maximum time the log strings are kept in the VW debug queue.
|
module-error-log-on
|
Indicates whether error logging is on for a particular module.
|
max-log-directory-size
|
Maximum size for the log directory.
|
max-log-number-of-files
|
Maximum number of files allowed in the logging directory.
|
module_config_level
|
Trace level for the module.
|
module_jdaq_level
|
module_fm_level
|
module_iptl1_level
|
module_jmoco_level
|
module_main_level
|
module_oss_level
|
module_parser_level
|
module_pm_level
|
module_poller_level
|
module_snmp_level
|
module_sw_level
|
module_gwtl1_level
|
module_telnet_tunnel_level
|
module_snmp_tunnel_level
|
module_na_level
|
module_platform_level
|
module_util_level
|
module_ne_level
|
module_gwcorba_level
|
module_data_level
|
module_sm_level
|
module_csm_level
|
archive-dir
|
Specifies the directory where the archive log files are saved. The default directory is /opt/CiscoTransportManagerServer/log.
|
max-archivelog-file
|
Specifies the maximum number of log files to archive on the server. The range is from 1 to 25 files.
|
enable-archive
|
If enabled, allows you to archive log files to facilitate longer-term collection of logging information. When a log file is about to wrap, you can save the regular log file to a separate archive file.
|
debug-logfile-size
|
Specifies the size of the Debug Log file. You can select a default log size for each log file.
|
error-logfile-size
|
Specifies the size of the Error Log file. You can select a default log size for each log file.
|
init-logfile-size
|
Specifies the size of the initialization log file. You can select a default log size for each log file.
|
server-monitor
|
monitoring-enabled
|
Enables or disables monitoring.
|
no-of-threads
|
Number of threads used for monitoring.
|
polling-period
|
Frequency at which monitoring is performed.
|
Disk_Usage_Enabled
|
Enables disk monitoring.
|
Disk_Usage_Critical
|
Critical threshold value for disk usage.
|
Disk_Usage_Major
|
Major threshold value for disk usage.
|
Disk_Usage_Minor
|
Minor threshold value for disk usage.
|
Disk_Usage_Units
|
Units in which disk usage is measured.
|
Memory_Usage_SWAP_Enabled
|
Enables monitoring for swap.
|
Memory_Usage_SWAP_Critical
|
Critical threshold value for swap usage.
|
Memory_Usage_SWAP_Major
|
Major threshold value for swap usage.
|
Memory_Usage_SWAP_Minor
|
Minor threshold value for swap usage.
|
Memory_Usage_SWAP_Units
|
Units in which swap usage is measured.
|
Memory_Usage_RAM_Enabled
|
Enables monitoring for RAM.
|
Memory_Usage_RAM_Critical
|
Critical threshold value for memory usage.
|
Memory_Usage_RAM_Major
|
Major threshold value for memory usage.
|
Memory_Usage_RAM_Minor
|
Minor threshold value for memory usage.
|
Memory_Usage_RAM_Units
|
Units in which memory usage is measured.
|
CPU_Usage_Enabled
|
Enables monitoring for CPU usage.
|
CPU_Usage_Critical
|
Critical threshold value for CPU usage.
|
CPU_Usage_Major
|
Major threshold value for CPU usage.
|
CPU_Usage_Minor
|
Minor threshold value for CPU usage.
|
CPU_Usage_Units
|
Units in which CPU usage is measured.
|
Prune_Time_Audit_Log_Enabled
|
Enables monitoring for the prune time audit log.
|
Prune_Time_Audit_Log_Critical
|
Critical threshold value for the prune time audit log.
|
Prune_Time_Audit_Log_Major
|
Major threshold value for the prune time audit log.
|
Prune_Time_Audit_Log_Minor
|
Minor threshold value for the prune time audit log.
|
Prune_Time_Audit_Log_Units
|
Units in which the prune time audit log is measured.
|
Prune_Time_Error_Log_Enabled
|
Enables monitoring for the prune time error log.
|
Prune_Time_Error_Log_Critical
|
Critical threshold value for the prune time error log.
|
Prune_Time_Error_Log_Major
|
Major threshold value for the prune time error log.
|
Prune_Time_Error_Log_Minor
|
Minor threshold value for the prune time error log.
|
Prune_Time_Error_Log_Units
|
Units in which the prune time error log is measured.
|
Prune_Time_Audit_Trail_Log_
Enabled
|
Enables monitoring for the prune time audit trail log.
|
Prune_Time_Audit_Trail_Log_
Critical
|
Critical threshold value for the prune time audit trail log.
|
Prune_Time_Audit_Trail_Log_Major
|
Major threshold value for the prune time audit trail log.
|
Prune_Time_Audit_Trail_Log_Minor
|
Minor threshold value for the prune time audit trail log.
|
Prune_Time_Audit_Trail_Log_Units
|
Units in which the prune time audit trail log is measured.
|
Prune_Time_Purge_NE_Enabled
|
Enables monitoring for the prune time purge NE.
|
Prune_Time_Purge_NE_Critical
|
Critical threshold value for the prune time purge NE.
|
Prune_Time_Purge_NE_Major
|
Major threshold value for the prune time purge NE.
|
Prune_Time_Purge_NE_Minor
|
Minor threshold value for the prune time purge NE.
|
Prune_Time_Purge_NE_Units
|
Units in which the prune time purge NE is measured.
|
Prune_Time_15min_PM_Enabled
|
Enables monitoring for the prune time 15-minute PM.
|
Prune_Time_15min_PM_Critical
|
Critical threshold value for the prune time 15-minute PM.
|
Prune_Time_15min_PM_Major
|
Major threshold value for the prune time 15-minute PM.
|
Prune_Time_15min_PM_Minor
|
Minor threshold value for the prune time 15-minute PM.
|
Prune_Time_15min_PM_Units
|
Units in which the prune time 15-minute PM is measured.
|
Prune_Time_1day_PM_Enabled
|
Enables monitoring for the prune time 24-hour PM.
|
Prune_Time_1day_PM_Critical
|
Critical threshold value for the prune time 24-hour PM.
|
Prune_Time_1day_PM_Major
|
Major threshold value for the prune time 24-hour PM.
|
Prune_Time_1day_PM_Minor
|
Minor threshold value for the prune time 24-hour PM.
|
Prune_Time_1day_PM_Units
|
Units in which the prune time 24-hour PM is measured.
|
Prune_Time_FM_Enabled
|
Enables monitoring for the prune time FM.
|
Prune_Time_FM_Critical
|
Critical threshold value for the prune time FM.
|
Prune_Time_FM_Major
|
Major threshold value for the rune time FM.
|
Prune_Time_FM_Minor
|
Minor threshold value for the prune time FM.
|
Prune_Time_FM_Units
|
Units in which the prune time FM is measured.
|
Prune_Time_Server_Monitor_Enabled
|
Enables monitoring for the prune time server monitor.
|
Prune_Time_Server_Monitor_Critical
|
Critical threshold value for the prune time server monitor.
|
Prune_Time_Server_Monitor_Major
|
Major threshold value for the prune time server monitor.
|
Prune_Time_Server_Monitor_Minor
|
Minor threshold value for the prune time server monitor.
|
Prune_Time_Server_Monitor_Units
|
Units in which the prune time server monitor is measured.
|
Prune_Time_Job_Monitor_Enabled
|
Enables monitoring for the prune time job monitor.
|
Prune_Time_Job_Monitor_Critical
|
Critical threshold value for the prune time job monitor.
|
Prune_Time_Job_Monitor_Major
|
Major threshold value for the prune time job monitor.
|
Prune_Time_Job_Monitor_Minor
|
Minor threshold value for the prune time job monitor.
|
Prune_Time_Job_Monitor_Units
|
Units in which the prune time job monitor is measured.
|
PM_Collection_Time_Enabled
|
Enables monitoring for the PM collection time.
|
PM_Collection_Time_Critical
|
Critical threshold value for the PM collection time.
|
PM_Collection_Time_Major
|
Major threshold value for the PM collection time.
|
PM_Collection_Time_Minor
|
Minor threshold value for the PM collection time.
|
PM_Collection_Time_Units
|
Units in which the PM collection time is measured.
|
Base_Circuit_Creation_Time_Enabled
|
Enables monitoring for the base circuit creation time.
|
Base_Circuit_Creation_Time_Critical
|
Critical threshold value for the base circuit creation time.
|
Base_Circuit_Creation_Time_Major
|
Major threshold value for the base circuit creation time.
|
Base_Circuit_Creation_Time_Minor
|
Minor threshold value for the base circuit creation time.
|
Base_Circuit_Creation_Time_Units
|
Units in which the base circuit creation time is measured.
|
Circuit_Creation_Time_Per_Hop_
Enabled
|
Enables monitoring for the circuit creation time.
|
Circuit_Creation_Time_Per_Hop_
Critical
|
Critical threshold value for the circuit creation time.
|
Circuit_Creation_Time_Per_Hop_
Major
|
Major threshold value for the circuit creation time.
|
Circuit_Creation_Time_Per_Hop_
Minor
|
Minor threshold value for the circuit creation time.
|
Circuit_Creation_Time_Per_Hop_
Units
|
Units in which the circuit creation time is measured.
|
NE_Synch_Time_Enabled
|
Enables monitoring for the NE synchronization time.
|
NE_Synch_Time_Critical
|
Critical threshold value for the NE synch time.
|
NE_Synch_Time_Major
|
Major threshold value for the NE synch time.
|
NE_Synch_Time_Minor
|
Minor threshold value for the NE synch time.
|
NE_Synch_Time_Units
|
Units in which the NE synch time is measured.
|
Config_Resynch_Time_Enabled
|
Enables monitoring for the config resynchronization time.
|
Config_Resynch_Time_Critical
|
Critical threshold for the config resynchronization time.
|
Config_Resynch_Time_Major
|
Major threshold for the config resynchronization time.
|
Config_Resynch_Time_Minor
|
Minor threshold for the config resynchronization time.
|
Config_Resynch_Time_Units
|
Units in which the config resynchronization time is measured.
|
critical-process
|
SMService
|
Indicates whether this process is critical or noncritical.
|
OracleService
|
OSAgent
|
mgx88xx-ne
|
mgx88xx-pm
|
ons15454-ne
|
ons15454-pm
|
ons15200-ne
|
(Not used)
|
ons155xx-ne
|
Indicates whether this process is critical or noncritical.
|
ons155xx-pm
|
ons15800-ne
|
ons158xx-pm
|
ons15801-ne
|
ons15808-ne
|
ons15454sdh-ne
|
ons15454sdh-pm
|
ons15216-ne
|
ons15600-pm
|
ons15600sdh-pm
|
ons15302-ne
|
ons15305-ne
|
ons1530x-pm
|
hfr-ne
|
Indicates whether this process is critical or noncritical.
|
hfr-pm
|
gsriox-ne
|
gsriox-pm
|
cat65xx-ne
|
snmp-trap-service
|
gw-corba-service
|
gwtl1-service
|
mds9000-ne
|
database
|
db-prune-db05-enabled
|
Indicates whether or not pruning of the archivelog directory /db05 is enabled. The default is not enabled.
|
db-prune-db05-threshold
|
Specifies that pruning of the /db05 directory will occur if the used capacity of /db05 crosses the threshold value. The default value is 80%.
|
db-prune-db05-backupdirectory
|
Backup directory for the /db05 directory. The default is /ctm_backup.
|
db-prune-db05-polling-period
|
Interval of pruning the /db05 directory if the threshold value is exceeded. The default is 15 minutes.
|
db-server-configuration
|
CTM database and server configuration type. Values are small, medium, large, or high-end.
|
db-archive-15min-pm-days
|
Number of days of 15-minute PM data to keep in the database. The default is 30 days.
|
db-archive-1day-pm-days
|
Number of days of 24-hour PM data to keep in the database. The default is 30 days.
|
db-archive-fm-days
|
Number of days of FM data to keep in the database. The default is 7 days.
|
db-archive-auditlog-days
|
Number of days of Audit Log data to keep in the database. The default is 7 days.
|
db-archive-errorlog-days
|
Number of days of Error Log data to keep in the database. The default is 7 days.
|
db-archive-audittrail-days
|
Number of days of audit trail data to keep in the database. The default is 7 days.
|
db-archive-server-monitor-days
|
Number of days of server monitor entries to keep in the database. The default is 7 days.
|
db-archive-server-jobmonitor-days
|
Number of days of job monitor entries to keep in the database. The default is 7 days.
|
db-prune-15min-pm-enabled
|
Flag to check whether data pruning is enabled.
|
db-prune-1day-pm-enabled
|
db-prune-pm-enabled
|
db-prune-fm-enabled
|
db-prune-auditlog-enabled
|
db-prune-errorlog-enabled
|
db-prune-audittrail-enabled
|
db-prune-server-monitor-enabled
|
db-prune-server-jobmonitor-enabled
|
daily-prune-15min-pm-time
|
Time of day when data will be pruned.
|
daily-prune-1day-pm-time
|
daily-prune-pm-time
|
daily-prune-fm-time
|
daily-prune-errorlog-time
|
daily-prune-auditlog-time
|
daily-prune-audittrail-time
|
daily-prune-server-monitor-time
|
daily-prune-server-jobmonitor-time
|
db-connection-pool-size
|
Number of connections in the JDBC connection pool. The default is 10.
|
db-connection-pool-size-pmservice
|
Number of connections in the JDBC connection pool for the PM service. The default is 10.
|
dbname
|
Name for the database, which is based on the release (for example, CTM7_0 for CTM R7.0).
|
dbversion
|
Version indicating the release (for example, 7.0).
|
db-diskspace-critical-threshold
|
Critical alarm is raised when used disk space crosses the threshold. The default is 90%.
|
db-diskspace-major-threshold
|
Major alarm is raised when used disk space crosses the threshold. The default is 80%.
|
db-diskspace-minor-threshold
|
Minor alarm is raised when used disk space crosses the threshold. The default is 70%.
|
db-archivelog-enabled
|
Whether or not the database archivelog mode option is enabled. The default is false (not enabled).
|
db-backup-state
|
State of the database hot backup. The default is 0.
|
db-export-state
|
State of the database export. The default is 0.
|
db-max-sessions
|
Maximum number of sessions that can be opened with the database. The default is 32 sessions.
|
db-no-pruning-threads
|
Number of threads that are configured to run the db prune script. The default is 1.
|
db-backup-failure-reason
|
Reason for the hot database backup failure.
|
db-export-failure-reason
|
Reason for database export failure.
|
ha
|
max-retries
|
If the first backup CTM server is not available, this field provides the number of times the client should retry logging in before moving to the next server in the list.
|
wait-time
|
If disruption to the primary CTM server occurs, this field provides the number of seconds the client should wait before attempting to log into the backup server.
|
server-name-list
|
Lists the CTM servers that CTM clients will log into if access to the primary CTM server is disrupted.
|
debug-telnet-port
|
Lists the Telnet port number to use for debugging. The default port number is 9410.
|
