Table Of Contents
Upgrading to CTM R6.0 from an Earlier Release
3.1 Upgrading from CTM R5.0.x to CTM R6.0 and Oracle9i on the Same Workstation
3.1.1 Downloading the Oracle Patch Installer
3.1.2 Downloading the 9.2.0.6 Patch for Oracle9i
3.1.3 Installing the 9.2.0.6 Patch for Oracle9i
3.1.4 Installing and Applying Additional Oracle Patches
3.1.5 Installing the CTM R6.0 Server and Upgrading the Database
3.1.6 Copying the Client Upgrade Files After the CTM Server Installation
3.2 Upgrading from CTM R5.0.x to CTM R6.0 and Oracle9i on Separate Workstations
3.2.1 Downloading the Oracle Patch Installer on the CTM Database Workstation
3.2.2 Downloading the 9.2.0.6 Patch for Oracle9i on the CTM Database Workstation
3.2.3 Installing the 9.2.0.6 Patch for Oracle9i on the CTM Database Workstation
3.2.4 Installing and Applying Additional Oracle Patches on the CTM Database Workstation
3.2.5 Upgrading the Database on the CTM Database Workstation
3.2.6 Downloading the Oracle Patch Installer on the CTM Server Workstation
3.2.7 Downloading the 9.2.0.6 Patch for Oracle9i on the CTM Server Workstation
3.2.8 Installing the 9.2.0.6 Patch for Oracle9i on the CTM Server Workstation
3.2.9 Installing and Applying Additional Oracle Patches on the CTM Server Workstation
3.2.10 Installing the CTM R6.0 Server on the CTM Server Workstation
3.2.11 Copying the Client Upgrade Files After the CTM Server Installation
3.3 Upgrading from CTM R4.7.x and Oracle8i to CTM R6.0 and Oracle9i on the Same Workstation
3.3.1 Setting the Environment for Installation
3.3.2 Installing the Oracle9i Software
3.3.3 Installing the Oracle9i Software with the .rsp Response File Provided by Cisco
3.3.4 Downloading the Oracle Patch Installer
3.3.5 Downloading the 9.2.0.6 Patch for Oracle9i
3.3.6 Installing the 9.2.0.6 Patch for Oracle9i
3.3.7 Installing and Applying Additional Oracle Patches
3.3.8 Installing the CTM R6.0 Server and Database and Migrating Basic Data
3.3.9 Copying the Client Upgrade Files After the CTM Server Installation
3.4 Upgrading from CTM R4.7.x and Oracle8i to CTM R6.0 and Oracle9i on Separate Workstations
3.4.1 Setting the Environment for Installation on the CTM Database Workstation
3.4.2 Installing the Oracle9i Software on the CTM Database Workstation
3.4.3 Installing the Oracle9i Software with the .rsp Response File Provided by Cisco on the CTM Database Workstation
3.4.4 Downloading the Oracle Patch Installer on the CTM Database Workstation
3.4.5 Downloading the 9.2.0.6 Patch for Oracle9i on the CTM Database Workstation
3.4.6 Installing the 9.2.0.6 Patch for Oracle9i on the CTM Database Workstation
3.4.7 Installing and Applying Additional Oracle Patches on the CTM Database Workstation
3.4.8 Installing the CTM R6.0 Database and Migrating Basic Data on the CTM Database Workstation
3.4.9 Installing the Oracle9i Client on the CTM Server Workstation
3.4.10 Updating the UNIX Environment on the CTM Server Workstation
3.4.11 Verifying the Oracle9i Client Connection on the CTM Server Workstation
3.4.12 Installing the CTM R6.0 Server
3.4.13 Copying the Client Upgrade Files After the CTM Server Installation
3.5 Upgrading from Cisco MGM R5.0 to CTM R6.0 and Oracle9i on the Same Workstation
3.5.1 Retaining 32-Bit Oracle
3.5.2 Upgrading from 32-Bit Oracle to 64-Bit Oracle
3.5.3 Installing the CTM R6.0 Server and Database and Migrating Basic Data
3.5.4 Copying the Client Upgrade Files After the CTM Server Installation
3.6 Upgrading from Cisco MGM R5.0 to CTM R6.0 and Oracle9i on Separate Workstations
3.6.1 Retaining 32-Bit Oracle
3.6.2 Upgrading from 32-Bit Oracle to 64-Bit Oracle on the CTM Database Workstation
3.6.3 Installing the CTM R6.0 Database and Migrating Basic Data on the CTM Database Workstation
3.6.4 Upgrading from 32-Bit Oracle to 64-Bit Oracle on the CTM Server Workstation
3.6.5 Installing the CTM R6.0 Server on the CTM Server Workstation
3.6.6 Copying the Client Upgrade Files After the CTM Server Installation
3.7 Verifying that the Oracle9i and CTM Server Processes Are Running
3.8 Setting Up Sudo
3.9 (Optional) Migrating Historical CTM R4.7.x Data
Upgrading to CTM R6.0 from an Earlier Release
This chapter describes how to upgrade to CTM R6.0 from an earlier release. If you are upgrading from your existing CTM installation to CTM R6.0, you can migrate basic NE information, users and profiles, topology information, OSS client data, and customized maps.
Note 
You can upgrade to CTM R6.0 directly from either CTM R4.7.x, CTM R5.0.x, or Cisco MGM R5.0.x. If you are upgrading from a release prior to CTM R4.7.x, you must first upgrade to CTM R4.7.x or CTM R5.0.x. Refer to Cisco Transport Manager Release 4.7 Installation Guide or Cisco Transport Manager Release 5.0 Installation Guide for the exact installation procedure. After you install CTM R4.7.x, CTM R5.0.x, or Cisco MGM R5.0, you can upgrade to CTM R6.0.
This chapter contains the following sections:
•Upgrading from CTM R5.0.x to CTM R6.0 and Oracle9i on the Same Workstation
•Upgrading from CTM R5.0.x to CTM R6.0 and Oracle9i on Separate Workstations
•Upgrading from CTM R4.7.x and Oracle8i to CTM R6.0 and Oracle9i on the Same Workstation
•Upgrading from CTM R4.7.x and Oracle8i to CTM R6.0 and Oracle9i on Separate Workstations
•Upgrading from Cisco MGM R5.0 to CTM R6.0 and Oracle9i on the Same Workstation
•Upgrading from Cisco MGM R5.0 to CTM R6.0 and Oracle9i on Separate Workstations
•Verifying that the Oracle9i and CTM Server Processes Are Running
•Setting Up Sudo
•(Optional) Migrating Historical CTM R4.7.x Data
Note After upgrading to CTM R6.0, the old CTM server directory is moved to CiscoTransportManagerServer-old. Any data previously saved under /opt/CiscoTransportManagerServer/admin, /opt/CiscoTransportManagerServer/images, /opt/CiscoTransportManagerServer/cms, /opt/CiscoTransportManagerServer/bin/jcorbagw.sh, /opt/CiscoTransportManagerServer/cfg/usr, and /opt/CiscoTransportManagerServer/cfg/corbagw.properties is saved under the new directory. Before removing the old version, move any relevant data to the new /opt/CiscoTransportManagerServer directory.
Caution When migrating basic data, the migration could stall if the /temp directory contains temporary files left over from previous upgrades. Remove all temporary files from /temp before upgrading CTM.
Caution When upgrading from CTM R5.0.x to CTM R6.0, the migration fails when the network partition ID is greater than 9. This is a known issue that is tracked as CSCsd51643. Refer to the
Release Notes for Cisco Transport Manager Release 6.0 for the steps to work around this problem.
Caution Before upgrading to CTM R6.0, verify that the NE versions in your network are supported by CTM R6.0. Refer to
Release Notes for Cisco Transport Manager Release 6.0 for the NE software versions that are supported. If your network contains NEs that are not supported in CTM R6.0, it will not be possible to discover or manage them.
Note For an explanation of error messages that you might encounter during the upgrade, see Appendix A, "Understanding Installation Error Messages."
Note If you need instructions to mount or unmount CDs, see Appendix C, "Mounting and Unmounting CDs on Sun Solaris."
3.1 Upgrading from CTM R5.0.x to CTM R6.0 and Oracle9i on the Same Workstation
This section describes how to upgrade from CTM R5.0.x to CTM R6.0 when you are installing the CTM R6.0 server and the Oracle9i database on the same Sun Solaris 8 server.
Caution Before upgrading your database to CTM R6.0, it is strongly recommended that you back up your CTM R5.0.x database. If you do so, you can revert to your old data in the event that the upgrade fails. To back up the database, see
Cisco Transport Manager Release 6.0 User Guide, which is available online at
http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/optnet/ctm/index.htm. Refer to the section "Backing Up the CTM Database from the CTM GUI."
Note The C shell is assumed for all UNIX commands.
3.1.1 Downloading the Oracle Patch Installer
Note The Oracle patch installer is used to install additional Oracle patches. If you already installed the Oracle patch installer, you can skip this section.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 2617419.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download.
Step 8 In the list of patches returned, click the first patch, which has the latest release number.
Note Do not be concerned if the patch refers to a later version of Oracle.
Step 9 In the Patch 2617419 window, go to the Platform or Language field and choose Generic Platform (the default).
Step 10 Click Download.
Step 11 Save the patch to the /oraclesw9i/product/9.2 directory.
Step 12 Enter the following commands to change the patch ownership and unzip the patch:
chown oracle:dba /oraclesw9i/product/9.2/p2617419_10102_GENERIC.zip
cd /oraclesw9i/product/9.2
unzip p2617419_10102_GENERIC.zip
3.1.2 Downloading the 9.2.0.6 Patch for Oracle9i
If you already have the 9.2.0.6 patch for Oracle9i installed, you can skip this section. To find out which patches have been installed, enter the following commands as the oracle user:
cd $ORACLE_HOME/OPatch/
./opatch lsinventory -detail | grep -i "oracle9i patch"
The output shows:
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 3948480.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p3948480_9206_SOLARIS.zip. For 64-bit Oracle, download p3948480_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory.
Step 9 As the oracle user, enter one of the following sets of commands to prepare the patch set, depending on your Oracle version:
•For 32-bit Oracle, enter:
unzip p3948480_9206_SOLARIS.zip
•For 64-bit Oracle, enter:
unzip p3948480_9206_SOLARIS64.zip
3.1.3 Installing the 9.2.0.6 Patch for Oracle9i
Note If you already have the 9.2.0.6 patch for Oracle9i installed, you can skip this section.
Step 1 Complete the following substeps to shut down all of the CTM clients:
a. In the Domain Explorer window, choose Administration > CTM Users.
b. In the CTM Users table, choose Administration > Logged In CTM Users.
c. In the Logged In CTM Users table, select the user whose session will be ended and choose Administration > Log Out User (or click the Log Out User tool).
d. Click Yes at the following prompt:
This operation will log out the selected CTM user. The process will take approximately
1 minute and this CTM client will be unusable until then. Do you wish to continue?
Wait while the CTM server logs out the selected CTM client. The CTM GUI is frozen for approximately 1 minute until the request is complete.
Step 2 As the root user, enter the following command to stop the workstation where the CTM server is running:
Step 3 Log in as the oracle user on the workstation where the CTM database is running and enter the following command to stop the Oracle listener:
Step 4 Enter the following commands to shut down all Oracle processes, if they are running:
Step 5 Insert disk one of the CTM installation CDs in the CD-ROM drive.
Step 6 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 7 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 8 Depending on your Oracle version, enter one of the following sets of commands to install the 9.2.0.6 patch:
•For 32-bit Oracle, enter:
cp /cdrom/cdrom0/Disk1/patchset.rsp /oraclesw9i
./runInstaller -responseFile /oraclesw9i/patchset.rsp
•For 64-bit Oracle, enter:
cp /cdrom/cdrom0/Disk1/patchset_64bit.rsp /oraclesw9i
./runInstaller -responseFile /oraclesw9i/patchset_64bit.rsp
Note If the Disk Location screen pops up, click Cancel.
Step 9 At the prompt to run the root.sh script, log into another terminal window as the root user and enter the following commands:
cd /oraclesw9i/product/9.2
Step 10 After the script finishes running, return to the prompt popup window and click OK.
Step 11 Click Next.
Step 12 Enter the following commands to eject the CD:
Step 13 After the patch is installed, read the Oracle patch README.html file to carry out the post-installation steps and check any caveats associated with this patch.
Step 14 Depending on your Oracle version, enter one of the following sets of commands to remove the 9.2.0.6 patch installation files:
•For 32-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS.zip
rm -rf /oraclesw9i/README.html
•For 64-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS64.zip
rm -rf /oraclesw9i/README.html
Step 15 Enter the following commands to update the Oracle data dictionary:
SQL> spool /oraclesw9i/patch.log
SQL> @?/rdbms/admin/catpatch.sql
Note Review the /oraclesw9i/patch.log file for errors and inspect the list of components that is displayed at the end of catpatch.sql script. This list provides the version and status of each SERVER component in the database. If necessary, repeat Step 15 to rerun the catpatch.sql script after correcting any problems.
SQL> shutdown
SQL> startup
SQL> @?/rdbms/admin/utlrp.sql
Note The utlrp.sql script is used to recompile all invalid PL/SQL packages now instead of when the packages are accessed for the first time. This command is optional but recommended.
3.1.4 Installing and Applying Additional Oracle Patches
Complete the following steps to install and apply additional required Oracle patches.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number field, enter 2733910.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p2733910_9206_SOLARIS.zip. For 64-bit Oracle, download p2733910_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Note The 32-bit patch 2733910 unzips to ./4092208. This is not an error.
Step 9 In the MetaLink window, click Patches.
Step 10 Click Simple Search.
Step 11 In the Search by Patch Number field, enter 4067938.
Step 12 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 13 Click Go.
Step 14 Click Download. For 32-bit Oracle, download p4067938_9206_SOLARIS.zip. For 64-bit Oracle, download p4067938_9206_SOLARIS64.zip.
Step 15 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 16 In the MetaLink window, click Patches.
Step 17 Click Simple Search.
Step 18 In the Search by Patch Number field, enter 4147836.
Step 19 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 20 Click Go.
Step 21 Click Download. For 32-bit Oracle, download p4147836_9206_SOLARIS.zip. For 64-bit Oracle, download p4147836_9206_SOLARIS64.zip.
Step 22 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 23 As the oracle user, enter the following commands to shut down the Oracle listener and all of the Oracle processes:
Step 24 For 64-bit Oracle only, the opatch apply command might fail. If this happens, edit the $ORACLE_HOME/inventory/ContentsXML/oraclehomeproperties.xml file by changing <ARU_ID>453</ARU_ID> to <ARU_ID>23</ARU_ID>. This is a known Oracle bug.
Step 25 Depending on your configuration, enter one of the following sets of commands as the oracle user to change directories to the patch directory and apply the 2733910 patch (which unzips to 4092208 on a 32-bit workstation):
•For 32-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
•For 64-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 26 Enter the following commands to change directories to the patch directory and apply the 4067938 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 27 Enter the following commands to change directories to the patch directory and apply the 4147836 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 28 As the oracle user, enter the following commands to start the CTM database and the Oracle listener:
3.1.5 Installing the CTM R6.0 Server and Upgrading the Database
If the CTM release that you are upgrading from is CTM R5.0.2.85.1 or R5.0.2.90.1, you must execute
the following SQL commands before proceeding with the CTM R6.0 upgrade:
sqlplus ctmanager/ctm123!
SQL> ALTER TABLE ONS15454_327_NE_Table DROP COLUMN NEUSERNAME;
SQL> ALTER TABLE ONS15454_327_NE_Table DROP COLUMN NEPASSWD;
Note If you changed the default password of ctm123! for the CTM ctmanager account, please use the correct password in the SQLPlus command.
To install the CTM server and upgrade the database, log in as the root user and complete the following steps:
Step 1 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 2 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 3 Insert the CTM Server Disk 1 installation CD and enter the following commands:
cdrom/cdrom0/Disk1/ctmsetup.sh
The setup program searches for Sun Microsystems JRE version 1.4.2_05 on your workstation.
Note If JRE is not installed, the setup program starts the Java installation program. Follow the prompts to install JRE. Enter yes at the following binary license code agreement prompt:
Do you agree to the above license terms? [yes or no]
Then, continue installing the CTM server and upgrading the database.
Note If the required Solaris patches are missing, you must install them manually. Click Cancel; then, click Quit. Download the patches from SunSolve Online at http://sunsolve.sun.com. After you install the patches, continue installing the CTM server and upgrading the database.
This website is Copyright © 2005, Sun Microsystems, Inc. All rights reserved.
Wait for up to 60 seconds while the following message appears:
Ctmsetup.sh is installing CTM server...
Step 4 Click Next at the Introduction screen.
Step 5 At the License Agreement screen, read the license agreement and click the I accept the terms of the license agreement radio button. Click Next.
Step 6 At the Installation Options screen, choose Upgrade from existing CTM release; then, click Next.
Step 7 At the Select Products screen, check the Install Cisco Transport Manager Server check box; then, click Next.
Note The Install Web Server check box is selected automatically when you choose Install Cisco Transport Manager Server. The Install Web Server option allows you to use an HTTP connection to download files from the CTM server to the CTM client. The web server is also used to launch the online help and CiscoView, which is an application used by CTM to configure and monitor ONS 155xx NEs. The web server is required for the CTM server.
Caution Do not check the other check boxes on the Select Products screen.
Note When you choose Install Cisco Transport Manager Server, the High Availability Installation option becomes available. This option applies only to HA installations. Do not choose it. To install HA, refer to Cisco Transport Manager High Availability Installation Guide for CTM R6.0.
Note The license for CTM GateWay/CORBA is sold separately. If you are using this feature in a production environment, you must purchase a license. You can install CTM GateWay/CORBA when you install the CTM server; however, this section assumes that you are installing the two products separately. For more information, see Chapter 4, "Installing CTM GateWay/CORBA R6.0."
Note The license for CiscoView is sold separately if used to manage the ONS 15530, ONS 15540 ESP, or ONS 15540 ESPx. If you are using this feature in a production environment to manage the ONS 15530, ONS 15540 ESP, or ONS 15540 ESPx, you must purchase a license for LAN Management Solution (LMS) Release 2.5, which includes CiscoView.
The license for CiscoView is bundled with CTM if used to manage the ONS 15501 DC or AC. You do not need to purchase a separate CiscoView license to manage the ONS 15501 DC or AC.
If you check the Install CiscoView Server check box, you receive the following prompt:
CiscoView installation has been moved to CTM Server Disk 3. After CTM server has been installed, insert the CTM Server Disk 3 and run the './installCiscoView.sh' script.
You must install the CTM server before you can install CiscoView. After installing the CTM server, see Chapter 6, "Installing and Setting Up CiscoView."
Step 8 At the CTM Group Information & Sudo Installation screen, complete the following substeps:
a. Enter the name of the UNIX group to which you want to assign administrator privileges.
b. To install sudo, check the Install CTM Sudo check box. If you do not want to install sudo, uncheck the check box.
c. Click Next.
Note For information about the sudo feature, see 1.4.1 Overview of Sudo Commands, page 1-12.
Step 9 At the FTP Information screen, complete the following substeps to configure an FTP account for ONS 15216 EDFA3 software download operations:
a. Enter the following information:
•FTP username
•FTP user password
•Confirm FTP user password
•FTP directory
b. Check or uncheck the Create new FTP Account check box. If checked, the FTP user will be created automatically on the CTM server workstation by the install script. If unchecked, it is assumed that an FTP user already exists on the CTM server workstation.
c. Click Next.
Note The FTP information that you enter during the CTM server installation can be modified later from the CTM client Control Panel window. Refer to Cisco Transport Manager Release 6.0 User Guide for more information.
Step 10 At the Main Options screen, complete the following substeps:
a. Check the Upgrade CTM database check box.
b. Check the Install CTM server check box.
c. Click Next.
Step 11 At the Server IP Address screen, specify an IP address for the CTM server. The Hostname field is automatically populated with the hostname of the selected IP address. After confirming the IP address and hostname details, click Next.
Step 12 At the Configure TFTP Server screen, complete the following substeps if you want to enable TFTP for the ONS 15216 EDFA2, ONS 15501, ONS 15530, and ONS 15540:
a. Check the Enable TFTP Server check box.
b. Enter the TFTP directory name. The default is /tftpboot.
c. Click Next.
Step 13 At the Destination Folder screen, specify where you want to install the CTM server. The default directory is /opt/CiscoTransportManagerServer. You can click Change to choose a different destination. After you specify your destination, click Next.
Note If the destination directory that you specified is a new directory, you will receive the message "Specified directory does not exist, create it?" Click Yes.
Caution CTM checks for the /opt/CiscoTransportManagerServer directory or a symbolic link to it. If CTM cannot find the /opt/CiscoTransportManagerServer directory or a symbolic link, CTM creates a symbolic link automatically. Therefore, do not delete any instances of /opt/CiscoTransportManagerServer from your CTM file structure.
Step 14 The Pre-Installation Summary screen shows the items that will be installed. Click Install.
Note It might take 30 to 60 minutes or longer to install the CTM server and upgrade the database, depending on your system performance.
Step 15 At the Insert New Media screen, complete the following substeps:
a. Eject the CTM Server Disk 1 installation CD, insert the CTM Server Disk 2 installation CD, and click Browse.
b. The Select a Folder dialog box opens. Double-click cdrom; then, single-click cdrom0. The filename text box now reads /cdrom/cdrom0.
c. In the Select a Folder dialog box, click Select.
d. In the Insert New Media screen, click OK.
Step 16 The Web Server Installation Summary screen summarizes the results of the web server installation. Click Next.
Step 17 The Install Complete screen summarizes the results of the installation. Click Done.
Step 18 (Optional) If you want to change the database name, enter the following commands as the root user:
Note Verify that the CTM server is stopped before running the change_db_name.sh script.
cd /opt/CiscoTransportManagerServer/bin
./change_db_name.sh <old_database_name> <new_database_name> <CTM_server_IP_address>
Step 19 Enter the following command to reboot the system. The CTM server starts automatically after rebooting:
Step 20 To verify that the CTM R6.0 server is running, enter the showctm command after the server reboots. The showctm command displays the CTM server version running as 6.0, followed by the build number. In the output, you will see two instances of "CTMServer," "SnmpTrapService," "SMService," and "Apache Web Server." This indicates that the CTM server is running. You should also see NE-specific processes, depending on your network. You might also see CTM GateWay/CORBA and CTM GateWay/TL1 instances.
3.1.6 Copying the Client Upgrade Files After the CTM Server Installation
You have two options for upgrading each client installation to the latest version of CTM that is on the server. You can choose to:
•Manually upgrade each client installation. If you have a previously installed version of the CTM client, you must delete the directory where the previous client is installed before installing the CTM R6.0 client. See 5.1 Installing the CTM Client and Cisco Edge Craft on Microsoft Windows, page 5-2 or 5.4 Installing the CTM Client and Cisco Edge Craft on Sun Solaris, page 5-6 for more information.
•Automatically upgrade each client when it connects to a server. During login, if the CTM client software version is older than the CTM server software version, the client will be prompted for upgrade. See 5.2 Starting the CTM Client in Microsoft Windows, page 5-5 or 5.5 Starting the CTM Client in Sun Solaris, page 5-8 for more information.
For this option you must copy the client installation files to the server. The CTM client and server installation files reside on separate installation CDs. To copy the client installation files to the server, you must eject the CTM server CD, insert the CTM client CD, and run an automated script, CopyUpgradeFiles.sh, to copy the client installation files to a specific folder under the CTM server installation directory. To do this, log in as the root user and complete the following steps.
Note The CTM server must be installed before completing the following steps.
Step 1 Enter the following commands to eject the CTM server installation CD:
Step 2 Insert the CTM client installation CD and enter the following commands:
3.2 Upgrading from CTM R5.0.x to CTM R6.0 and Oracle9i on Separate Workstations
This section describes how to upgrade from CTM R5.0.x to CTM R6.0 when you are installing the CTM R6.0 server and the Oracle9i database on separate Sun Solaris 8 servers.
Caution Before upgrading your database to CTM R6.0, it is strongly recommended that you back up your CTM R5.0.x database. If you do so, you can revert to your old data in the event that the upgrade fails. To back up the database, see
Cisco Transport Manager Release 6.0 User Guide, which is available online at
http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/optnet/ctm/index.htm. Refer to the section "Backing Up the CTM Database from the CTM GUI."
Note The C shell is assumed for all UNIX commands.
3.2.1 Downloading the Oracle Patch Installer on the CTM Database Workstation
Note The Oracle patch installer is used to install additional Oracle patches. If you already installed the Oracle patch installer, you can skip this section.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 2617419.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download.
Step 8 In the list of patches returned, click the first patch, which has the latest release number.
Note Do not be concerned if the patch refers to a later version of Oracle.
Step 9 In the Patch 2617419 window, go to the Platform or Language field and choose Generic Platform (the default).
Step 10 Click Download.
Step 11 Save the patch to the /oraclesw9i/product/9.2 directory.
Step 12 Enter the following commands to change the patch ownership and unzip the patch:
chown oracle:dba /oraclesw9i/product/9.2/p2617419_10102_GENERIC.zip
cd /oraclesw9i/product/9.2
unzip p2617419_10102_GENERIC.zip
3.2.2 Downloading the 9.2.0.6 Patch for Oracle9i on the CTM Database Workstation
If you already have the 9.2.0.6 patch for Oracle9i installed, you can skip this section. To find out which patches have been installed, enter the following commands as the oracle user:
cd $ORACLE_HOME/OPatch/
./opatch lsinventory -detail | grep -i "oracle9i patch"
The output shows:
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 3948480.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p3948480_9206_SOLARIS.zip. For 64-bit Oracle, download p3948480_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory.
Step 9 As the oracle user, enter one of the following sets of commands to prepare the patch set, depending on your Oracle version:
•For 32-bit Oracle, enter:
unzip p3948480_9206_SOLARIS.zip
•For 64-bit Oracle, enter:
unzip p3948480_9206_SOLARIS64.zip
3.2.3 Installing the 9.2.0.6 Patch for Oracle9i on the CTM Database Workstation
Note If you already have the 9.2.0.6 patch for Oracle9i installed, you can skip this section.
Step 1 Complete the following substeps to shut down all of the CTM clients:
a. In the Domain Explorer window, choose Administration > CTM Users.
b. In the CTM Users table, choose Administration > Logged In CTM Users.
c. In the Logged In CTM Users table, select the user whose session will be ended and choose Administration > Log Out User (or click the Log Out User tool).
d. Click Yes at the following prompt:
This operation will log out the selected CTM user. The process will take approximately
1 minute and this CTM client will be unusable until then. Do you wish to continue?
Wait while the CTM server logs out the selected CTM client. The CTM GUI is frozen for approximately 1 minute until the request is complete.
Step 2 As the root user, enter the following command to stop the workstation where the CTM server is running:
Step 3 Log in as the oracle user on the workstation where the CTM database is running and enter the following command to stop the Oracle listener:
Step 4 Enter the following commands to shut down all Oracle processes, if they are running:
Step 5 Insert disk one of the CTM installation CDs in the CD-ROM drive.
Step 6 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 7 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 8 Depending on your Oracle version, enter one of the following sets of commands to install the 9.2.0.6 patch:
•For 32-bit Oracle, enter:
./runInstaller -responseFile /oraclesw9i/patchset.rsp
•For 64-bit Oracle, enter:
./runInstaller -responseFile /oraclesw9i/patchset_64bit.rsp
Note If the Disk Location screen pops up, click Cancel.
Step 9 At the prompt to run the root.sh script, log into another terminal window as the root user and enter the following commands:
cd /oraclesw9i/product/9.2
Step 10 After the script finishes running, return to the prompt popup window and click OK.
Step 11 Click Next.
Step 12 Enter the following commands to eject the CD:
Step 13 After the patch is installed, read the Oracle patch README.html file to carry out the post-installation steps and check any caveats associated with this patch.
Step 14 Depending on your Oracle version, enter one of the following sets of commands to remove the 9.2.0.6 patch installation files:
•For 32-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS.zip
rm -rf /oraclesw9i/README.html
•For 64-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS64.zip
rm -rf /oraclesw9i/README.html
Step 15 Enter the following commands to update the Oracle data dictionary:
SQL> spool /oraclesw9i/patch.log
SQL> @?/rdbms/admin/catpatch.sql
Note Review the /oraclesw9i/patch.log file for errors and inspect the list of components that is displayed at the end of catpatch.sql script. This list provides the version and status of each SERVER component in the database. If necessary, repeat Step 15 to rerun the catpatch.sql script after correcting any problems.
SQL> shutdown
SQL> startup
SQL> @?/rdbms/admin/utlrp.sql
Note The utlrp.sql script is used to recompile all invalid PL/SQL packages now instead of when the packages are accessed for the first time. This command is optional but recommended.
3.2.4 Installing and Applying Additional Oracle Patches on the CTM Database Workstation
Complete the following steps to install and apply additional required Oracle patches.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number field, enter 2733910.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p2733910_9206_SOLARIS.zip. For 64-bit Oracle, download p2733910_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Note The 32-bit patch 2733910 unzips to ./4092208. This is not an error.
Step 9 In the MetaLink window, click Patches.
Step 10 Click Simple Search.
Step 11 In the Search by Patch Number field, enter 4067938.
Step 12 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 13 Click Go.
Step 14 Click Download. For 32-bit Oracle, download p4067938_9206_SOLARIS.zip. For 64-bit Oracle, download p4067938_9206_SOLARIS64.zip.
Step 15 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 16 In the MetaLink window, click Patches.
Step 17 Click Simple Search.
Step 18 In the Search by Patch Number field, enter 4147836.
Step 19 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 20 Click Go.
Step 21 Click Download. For 32-bit Oracle, download p4147836_9206_SOLARIS.zip. For 64-bit Oracle, download p4147836_9206_SOLARIS64.zip.
Step 22 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 23 As the oracle user, enter the following commands to shut down the Oracle listener and all of the Oracle processes:
Step 24 For 64-bit Oracle only, the opatch apply command might fail. If this happens, edit the $ORACLE_HOME/inventory/ContentsXML/oraclehomeproperties.xml file by changing <ARU_ID>453</ARU_ID> to <ARU_ID>23</ARU_ID>. This is a known Oracle bug.
Step 25 Depending on your configuration, enter one of the following sets of commands as the oracle user to change directories to the patch directory and apply the 2733910 patch (which unzips to 4092208 on a 32-bit workstation):
•For 32-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
•For 64-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 26 Enter the following commands to change directories to the patch directory and apply the 4067938 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 27 Enter the following commands to change directories to the patch directory and apply the 4147836 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 28 As the oracle user, enter the following commands to start the CTM database and the Oracle listener:
3.2.5 Upgrading the Database on the CTM Database Workstation
To upgrade the database, log in as the root user on the CTM database workstation and complete the following steps:
Step 1 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 2 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 3 Insert the CTM Server Disk 1 installation CD and enter the following commands:
cdrom/cdrom0/Disk1/ctmsetup.sh
The setup program searches for Sun Microsystems JRE version 1.4.2_05 on your workstation.
Note If JRE is not installed, the setup program starts the Java installation program. Follow the prompts to install JRE. Enter yes at the following binary license code agreement prompt:
Do you agree to the above license terms? [yes or no]
Then, continue upgrading the database.
Note If the required Solaris patches are missing, you must install them manually. Click Cancel; then, click Quit. Download the patches from SunSolve Online at http://sunsolve.sun.com. After you install the patches, continue installing the CTM server and database.
This website is Copyright © 2005, Sun Microsystems, Inc. All rights reserved.
Wait for up to 60 seconds while the following message appears:
Ctmsetup.sh is installing CTM server...
Step 4 Click Next at the Introduction screen.
Step 5 At the License Agreement screen, read the license agreement and click the I accept the terms of the license agreement radio button. Click Next.
Step 6 At the Installation Options screen, choose Upgrade from existing CTM release; then, click Next.
Step 7 At the Select Products screen, check the Install Cisco Transport Manager Server check box; then, click Next.
Note The Install Web Server check box is selected automatically when you choose Install Cisco Transport Manager Server. The Install Web Server option allows you to use an HTTP connection to download files from the CTM server to the CTM client. The web server is also used to launch the online help and CiscoView, which is an application used by CTM to configure and monitor ONS 155xx NEs. The web server is required for the CTM server.
Caution Do not check the other check boxes on the Select Products screen.
Note When you choose Install Cisco Transport Manager Server, the High Availability Installation option becomes available. This option applies only to HA installations. Do not choose it. To install HA, refer to Cisco Transport Manager High Availability Installation Guide for CTM R6.0.
Note The license for CTM GateWay/CORBA is sold separately. If you are using this feature in a production environment, you must purchase a license. You can install CTM GateWay/CORBA when you install the CTM server; however, this section assumes that you are installing the two products separately. For more information, see Chapter 4, "Installing CTM GateWay/CORBA R6.0."
Note The license for CiscoView is sold separately if used to manage the ONS 15530, ONS 15540 ESP, or ONS 15540 ESPx. If you are using this feature in a production environment to manage the ONS 15530, ONS 15540 ESP, or ONS 15540 ESPx, you must purchase a license for LAN Management Solution (LMS) Release 2.5, which includes CiscoView.
The license for CiscoView is bundled with CTM if used to manage the ONS 15501 DC or AC. You do not need to purchase a separate CiscoView license to manage the ONS 15501 DC or AC.
If you check the Install CiscoView Server check box, you receive the following prompt:
CiscoView installation has been moved to CTM Server Disk 3. After CTM server has been installed, insert the CTM Server Disk 3 and run the './installCiscoView.sh' script.
You must install the CTM server before you can install CiscoView. After installing the CTM server, see Chapter 6, "Installing and Setting Up CiscoView."
Step 8 At the CTM Group Information & Sudo Installation screen, complete the following substeps:
a. Enter the name of the UNIX group to which you want to assign administrator privileges.
b. To install sudo, check the Install CTM Sudo check box. If you do not want to install sudo, uncheck the check box.
c. Click Next.
Note For information about the sudo feature, see 1.4.1 Overview of Sudo Commands, page 1-12.
Step 9 At the FTP Information screen, accept the default selections; then, click Next.
Step 10 At the Main Options screen, check only the Upgrade CTM database check box; then, click Next.
Note Be sure to uncheck the Install CTM server check box.
Step 11 At the Specify CTM Server to Connect to screen, enter the IP address or hostname of the CTM server workstation; then, click Next.
Note If you entered a hostname, the setup program automatically translates the hostname to a physical IP address and prompts you to confirm the address. Click Yes.
Step 12 The Pre-Installation Summary screen shows the items that will be installed. Click Install.
Note It might take 20 minutes or longer to upgrade the database, depending on your system performance.
Step 13 The Install Complete screen summarizes the results of the installation. Click Done.
3.2.6 Downloading the Oracle Patch Installer on the CTM Server Workstation
Note The Oracle patch installer is used to install additional Oracle patches. If you already installed the Oracle patch installer, you can skip this section.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 2617419.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download.
Step 8 In the list of patches returned, click the first patch, which has the latest release number.
Note Do not be concerned if the patch refers to a later version of Oracle.
Step 9 In the Patch 2617419 window, go to the Platform or Language field and choose Generic Platform (the default).
Step 10 Click Download.
Step 11 Save the patch to the /oraclesw9i/product/9.2 directory.
Step 12 Enter the following commands to change the patch ownership and unzip the patch:
chown oracle:dba /oraclesw9i/product/9.2/p2617419_10102_GENERIC.zip
cd /oraclesw9i/product/9.2
unzip p2617419_10102_GENERIC.zip
3.2.7 Downloading the 9.2.0.6 Patch for Oracle9i on the CTM Server Workstation
Note If you already have the 9.2.0.6 patch for Oracle9i installed, you can skip this section.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 3948480.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p3948480_9206_SOLARIS.zip. For 64-bit Oracle, download p3948480_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory.
Step 9 As the oracle user, enter one of the following sets of commands to prepare the patch set, depending on your Oracle version:
•For 32-bit Oracle, enter:
unzip p3948480_9206_SOLARIS.zip
•For 64-bit Oracle, enter:
unzip p3948480_9206_SOLARIS64.zip
3.2.8 Installing the 9.2.0.6 Patch for Oracle9i on the CTM Server Workstation
Note If you already have the 9.2.0.6 patch for Oracle9i installed, you can skip this section.
Step 1 Complete the following substeps to shut down all of the CTM clients:
a. In the Domain Explorer window, choose Administration > CTM Users.
b. In the CTM Users table, choose Administration > Logged In CTM Users.
c. In the Logged In CTM Users table, select the user whose session will be ended and choose Administration > Log Out User (or click the Log Out User tool).
d. Click Yes at the following prompt:
This operation will log out the selected CTM user. The process will take approximately
1 minute and this CTM client will be unusable until then. Do you wish to continue?
Wait while the CTM server logs out the selected CTM client. The CTM GUI is frozen for approximately 1 minute until the request is complete.
Step 2 As the root user, enter the following command to stop the workstation where the CTM server is running:
Step 3 Insert disk one of the CTM installation CDs in the CD-ROM drive.
Step 4 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 5 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 6 Depending on your Oracle version, enter one of the following sets of commands to install the 9.2.0.6 patch:
•For 32-bit Oracle, enter:
cp /cdrom/cdrom0/Disk1/patchset.rsp /oraclesw9i
./runInstaller -responseFile /oraclesw9i/patchset.rsp
•For 64-bit Oracle, enter:
cp /cdrom/cdrom0/Disk1/patchset_64bit.rsp /oraclesw9i
./runInstaller -responseFile /oraclesw9i/patchset_64bit.rsp
Note If the Disk Location screen pops up, click Cancel.
Step 7 At the prompt to run the root.sh script, log into another terminal window as the root user and enter the following commands:
cd /oraclesw9i/product/9.2
Step 8 After the script finishes running, return to the prompt popup window and click OK.
Step 9 Click Next.
Step 10 Enter the following commands to eject the CD:
Step 11 After the patch is installed, read the Oracle patch README.html file to carry out the post-installation steps and check any caveats associated with this patch.
Step 12 Depending on your Oracle version, enter one of the following sets of commands to remove the 9.2.0.6 patch installation files:
•For 32-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS.zip
rm -rf /oraclesw9i/README.html
•For 64-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS64.zip
rm -rf /oraclesw9i/README.html
3.2.9 Installing and Applying Additional Oracle Patches on the CTM Server Workstation
Complete the following steps to install and apply additional required Oracle patches.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number field, enter 2733910.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p2733910_9206_SOLARIS.zip. For 64-bit Oracle, download p2733910_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Note The 32-bit patch 2733910 unzips to ./4092208. This is not an error.
Step 9 In the MetaLink window, click Patches.
Step 10 Click Simple Search.
Step 11 In the Search by Patch Number field, enter 4067938.
Step 12 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 13 Click Go.
Step 14 Click Download. For 32-bit Oracle, download p4067938_9206_SOLARIS.zip. For 64-bit Oracle, download p4067938_9206_SOLARIS64.zip.
Step 15 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 16 In the MetaLink window, click Patches.
Step 17 Click Simple Search.
Step 18 In the Search by Patch Number field, enter 4147836.
Step 19 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 20 Click Go.
Step 21 Click Download. For 32-bit Oracle, download p4147836_9206_SOLARIS.zip. For 64-bit Oracle, download p4147836_9206_SOLARIS64.zip.
Step 22 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 23 For 64-bit Oracle only, the opatch apply command might fail. If this happens, edit the $ORACLE_HOME/inventory/ContentsXML/oraclehomeproperties.xml file by changing <ARU_ID>453</ARU_ID> to <ARU_ID>23</ARU_ID>. This is a known Oracle bug.
Step 24 Depending on your configuration, enter one of the following sets of commands as the oracle user to change directories to the patch directory and apply the 2733910 patch (which unzips to 4092208 on a 32-bit workstation):
•For 32-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
•For 64-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 25 Enter the following commands to change directories to the patch directory and apply the 4067938 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 26 Enter the following commands to change directories to the patch directory and apply the 4147836 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
3.2.10 Installing the CTM R6.0 Server on the CTM Server Workstation
If the CTM release that you are upgrading from is CTM R5.0.2.85.1 or R5.0.2.90.1, you must execute
the following SQL commands before proceeding with the CTM R6.0 upgrade:
sqlplus ctmanager/ctm123!
SQL> ALTER TABLE ONS15454_327_NE_Table DROP COLUMN NEUSERNAME;
SQL> ALTER TABLE ONS15454_327_NE_Table DROP COLUMN NEPASSWD;
Note If you changed the default password of ctm123! for the CTM ctmanager account, please use the correct password in the SQLPlus command.
To install the CTM server, log in as the root user on the workstation where the CTM server will run and complete the following steps:
Step 1 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 2 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 3 Insert the CTM Server Disk 1 installation CD and enter the following commands:
cdrom/cdrom0/Disk1/ctmsetup.sh
The setup program searches for Sun Microsystems JRE version 1.4.2_05 on your workstation.
Note If JRE is not installed, the setup program starts the Java installation program. Follow the prompts to install JRE. Enter yes at the following binary license code agreement prompt:
Do you agree to the above license terms? [yes or no]
Then, continue installing the CTM server.
Note If the required Solaris patches are missing, you must install them manually. Click Cancel; then, click Quit. Download the patches from SunSolve Online at http://sunsolve.sun.com. After you install the patches, continue installing the CTM server.
This website is Copyright © 2005, Sun Microsystems, Inc. All rights reserved.
Wait for up to 60 seconds while the following message appears:
Ctmsetup.sh is installing CTM server...
Step 4 Click Next at the Introduction screen.
Step 5 At the License Agreement screen, read the license agreement and click the I accept the terms of the license agreement radio button. Click Next.
Step 6 At the Installation Options screen, choose Upgrade from existing CTM release; then, click Next.
Step 7 At the Select Products screen, check the Install Cisco Transport Manager Server check box; then, click Next.
Caution Do not check the other check boxes on the Select Products screen.
Step 8 At the CTM Group Information & Sudo Installation screen, complete the following substeps:
a. Enter the name of the UNIX group to which you want to assign administrator privileges.
b. To install sudo, check the Install CTM Sudo check box. If you do not want to install sudo, uncheck the check box.
c. Click Next.
Step 9 At the FTP Information screen, complete the following substeps to configure an FTP account for ONS 15216 EDFA3 software download operations:
a. Enter the following information:
•FTP username
•FTP user password
•Confirm FTP user password
•FTP directory
b. Check or uncheck the Create new FTP Account check box. If checked, the FTP user will be created automatically on the CTM server workstation by the install script. If unchecked, it is assumed that an FTP user already exists on the CTM server workstation.
c. Click Next.
Note The FTP information that you enter during the CTM server installation can be modified later from the CTM client Control Panel window. Refer to Cisco Transport Manager Release 6.0 User Guide for more information.
Step 10 At the Main Options screen, check only the Install CTM server check box; then, click Next.
Note Be sure to uncheck the Upgrade CTM database check box.
Step 11 At the Server IP Address screen, specify an IP address for the CTM server. The Hostname field is automatically populated with the hostname of the selected IP address. After confirming the IP address and hostname details, click Next.
Step 12 At the Configure TFTP Server screen, complete the following substeps if you want to enable TFTP for the ONS 15216 EDFA2, ONS 15501, ONS 15530, and ONS 15540:
a. Check the Enable TFTP Server check box.
b. Enter the TFTP directory name. The default is /tftpboot.
c. Click Next.
Step 13 At the Specify CTM Database to Connect to screen, enter the IP address or hostname of the database workstation; then, click Next.
Caution Be sure to enter the correct IP address or hostname. Do not simply accept the default.
Note If you entered a hostname, the setup program automatically translates the hostname to a physical IP address and prompts you to confirm the address. Click Yes.
Step 14 At the Destination Folder screen, specify where you want to install the CTM server. The default directory is /opt/CiscoTransportManagerServer. You can click Change to choose a different destination. After you specify your destination, click Next.
Note If the destination directory that you specified is a new directory, you will receive the message "Specified directory does not exist, create it?" Click Yes.
Caution CTM checks for the /opt/CiscoTransportManagerServer directory or a symbolic link to it. If CTM cannot find the /opt/CiscoTransportManagerServer directory or a symbolic link, CTM creates a symbolic link automatically. Therefore, do not delete any instances of /opt/CiscoTransportManagerServer from your CTM file structure.
Step 15 The Pre-Installation Summary screen shows the items that will be installed. Click Install.
Note It might take 20 minutes or longer to install the server, depending on your system performance.
Step 16 At the Insert New Media screen, complete the following substeps:
a. Eject the CTM Server Disk 1 installation CD, insert the CTM Server Disk 2 installation CD, and click Browse.
b. The Select a Folder dialog box opens. Double-click cdrom; then, single-click cdrom0. The filename text box now reads /cdrom/cdrom0.
c. In the Select a Folder dialog box, click Select.
d. In the Insert New Media screen, click OK.
Step 17 The Web Server Installation Summary screen summarizes the results of the web server installation. Click Next.
Step 18 The Install Complete screen summarizes the results of the installation. Click Done.
Step 19 (Optional) If you want to change the database name, enter the following commands as the root user on the CTM database workstation:
Caution Be sure to enter the following commands on the CTM database workstation, not on the CTM server workstation. Also, verify that the CTM server is stopped before running the change_db_name.sh script.
cd /opt/CiscoTransportManagerServer/bin
./change_db_name.sh <old_database_name> <new_database_name> <CTM_server_IP_address>
Step 20 Enter the following command to reboot the system. The CTM server starts automatically after rebooting:
Step 21 To verify that the CTM R6.0 server is running, enter the showctm command after the server reboots. The showctm command displays the CTM server version running as 6.0, followed by the build number. In the output, you will see two instances of "CTMServer," "SnmpTrapService," "SMService," and "Apache Web Server." This indicates that the CTM server is running. You should also see NE-specific processes, depending on your network. You might also see CTM GateWay/CORBA and CTM GateWay/TL1 instances.
3.2.11 Copying the Client Upgrade Files After the CTM Server Installation
You have two options for upgrading each client installation to the latest version of CTM that is on the server. You can choose to:
•Manually upgrade each client installation. If you have a previously installed version of the CTM client, you must delete the directory where the previous client is installed before installing the CTM R6.0 client. See 5.1 Installing the CTM Client and Cisco Edge Craft on Microsoft Windows, page 5-2 or 5.4 Installing the CTM Client and Cisco Edge Craft on Sun Solaris, page 5-6 for more information.
•Automatically upgrade each client when it connects to a server. During login, if the CTM client software version is older than the CTM server software version, the client will be prompted for upgrade. See 5.2 Starting the CTM Client in Microsoft Windows, page 5-5 or 5.5 Starting the CTM Client in Sun Solaris, page 5-8 for more information.
For this option you must copy the client installation files to the server. The CTM client and server installation files reside on separate installation CDs. To copy the client installation files to the server, you must eject the CTM server CD, insert the CTM client CD, and run an automated script, CopyUpgradeFiles.sh, to copy the client installation files to a specific folder under the CTM server installation directory. To do this, log in as the root user and complete the following steps.
Note The CTM server must be installed before completing the following steps.
Step 1 Enter the following commands to eject the CTM server installation CD:
Step 2 Insert the CTM client installation CD and enter the following commands:
3.3 Upgrading from CTM R4.7.x and Oracle8i to CTM R6.0 and Oracle9i on the Same Workstation
This section describes how to upgrade from CTM R4.7.x and Oracle8i to CTM R6.0 and Oracle9i when you are installing the CTM R6.0 server and the Oracle9i database on the same Sun Solaris 8 server.
Caution Before upgrading your database to CTM R6.0, it is strongly recommended that you back up your CTM R4.7.x database. If you do so, you can revert to your old data in the event that the upgrade fails. To back up the database, see
Cisco Transport Manager Release 6.0 User Guide, which is available online at
http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/optnet/ctm/index.htm. Refer to the section "Backing Up the CTM Database from the CTM GUI."
Note The C shell is assumed for all UNIX commands.
3.3.1 Setting the Environment for Installation
To set the environment for installation, log in as the root user and complete the following steps:
Step 1 Enter the following command to verify that the disk directories shown in Table 3-1 exist:
Table 3-1 Disk Directories
Directory
|
Contents
|
/db01
|
For the system tablespace used by Oracle
|
/db02
|
For the basedata tablespace, the alarmdata tablespace, the eventdata tablespace used by CTM, and the system tablespace used by Oracle
|
/db03
|
For the data tablespace used by CTM
|
/db04
|
For the INDEX tablespace used by CTM
|
/db051
|
For the archived logs
|
/ctm_backup2
|
For the backed-up database and configuration files
|
/oraclesw9i
|
For the Oracle software
|
/tftpboot
|
For the TFTP directory
Note Disk partitioning is not required for /tftpboot, but the directory is required.
|
Step 2 Enter the following command to modify the password file:
Step 3 Navigate to the entry that looks similar to the following:
oracle:x:100:3303::/oraclesw:/bin/csh
Step 4 In the entry, change /oraclesw to /oraclesw9i. The entry should now look similar to the following:
oracle:x:100:3303::/oraclesw9i:/bin/csh
Step 5 Enter the following command to save the changes:
3.3.2 Installing the Oracle9i Software
Step 1 Insert the CTM Server Disk 1 installation CD and enter the following command:
Step 2 Enter the following command to list the files in the cdrom/cdrom0/Disk1 directory:
Note If a list of files is returned, it indicates that you can access the CD-ROM successfully. If no files are visible, or if an error message is returned, refer to Sun Solaris documentation for mounting the CD-ROM.
Step 3 Enter the following command to copy the default profile to the Oracle home directory:
cp /cdrom/cdrom0/Disk1/InstData/Solaris/VM/cfg/{small | medium | large | highend}/.cshrc
/oraclesw9i/.cshrc
For example, to copy the default profile for a small network, enter:
cp /cdrom/cdrom0/Disk1/InstData/Solaris/VM/cfg/small/.cshrc /oraclesw9i/.cshrc
Note If you installed Oracle Standard Edition, you must copy the default profile for a small network.
Step 4 Enter the following command to determine what type of applications you can run on your operating system (OS):
If the output reads "64-bit sparcv9 kernel modules," you can run both 64-bit and 32-bit applications. If the output reads "32-bit sparcv9 kernel modules," you can run only 32-bit applications.
Note It is recommended that you be able to run both 64-bit and 32-bit applications.
Step 5 Complete one of the following options, depending on your Oracle version:
•If you are installing 32-bit Oracle Enterprise Edition, enter:
cp /cdrom/cdrom0/Disk1/svrcustom.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset.rsp /oraclesw9i
•If you are installing 64-bit Oracle Enterprise Edition, enter:
cp /cdrom/cdrom0/Disk1/svrcustom_64bit.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset_64bit.rsp /oraclesw9i
•If you are installing 32-bit Oracle Standard Edition, enter:
cp /cdrom/cdrom0/Disk1/svrcustom_std.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset.rsp /oraclesw9i
•If you are installing 64-bit Oracle Standard Edition, enter:
cp /cdrom/cdrom0/Disk1/svrcustom_std_64bit.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset_64bit.rsp /oraclesw9i
Step 6 (Optional) Enter the following commands to change ownership of the Oracle software directories:
/usr/bin/chown -R oracle:dba /oraclesw9i
/usr/bin/chown -R oracle:dba /db01
/usr/bin/chown -R oracle:dba /db02
/usr/bin/chown -R oracle:dba /db03
/usr/bin/chown -R oracle:dba /db04
/usr/bin/chown -R oracle:dba /db05
/usr/bin/chown -R oracle:dba /ctm_backup
Step 7 Enter the following commands to eject the CTM Server Disk 1 installation CD:
Step 8 If you are using an xterm window or a remote host, enter the following command to enable the xterm connection from the clients:
3.3.3 Installing the Oracle9i Software with the .rsp Response File Provided by Cisco
Step 1 Complete the following substeps to shut down all of the CTM clients:
a. In the Domain Explorer window, choose Administration > CTM Users.
b. In the CTM Users table, choose Administration > Logged In CTM Users.
c. In the Logged In CTM Users table, select the user whose session will be ended and choose Administration > Log Out User (or click the Log Out User tool).
d. Click Yes at the following prompt:
This operation will log out the selected CTM user. The process will take approximately
1 minute and this CTM client will be unusable until then. Do you wish to continue?
Wait while the CTM server logs out the selected CTM client. The CTM GUI is frozen for approximately 1 minute until the request is complete.
Step 2 As the root user, enter the following command to stop the workstation where the CTM server is running:
Step 3 Enter the following command to remove the oraInst.loc file, if it exists:
rm /var/opt/oracle/oraInst.loc
Step 4 On the workstation where the CTM database is running, enter the following commands to stop the Oracle listener and shut down all Oracle processes, if they are running:
Step 5 Enter the following command to log in as the oracle user:
Tip To verify the username, enter the id command.
Step 6 Insert disk one of the Oracle9i installation CDs in the CD-ROM drive.
Step 7 Enter the following command to set the display on your terminal:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 8 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 9 Complete one of the following options, depending on your Oracle version:
•If you are installing 32-bit Oracle Enterprise Edition, enter the following commands to start the Oracle Installer:
./runInstaller -responseFile /oraclesw9i/svrcustom.rsp &
•If you are installing 64-bit Oracle Enterprise Edition, enter the following commands to start the Oracle Installer:
./runInstaller -responseFile /oraclesw9i/svrcustom_64bit.rsp &
•If you are installing 32-bit Oracle Standard Edition, enter the following command to start the Oracle Installer:
./runInstaller -responseFile /oraclesw9i/svrcustom_std.rsp &
•If you are installing 64-bit Oracle Standard Edition, enter the following command to start the Oracle Installer:
./runInstaller -responseFile /oraclesw9i/svrcustom_std_64bit.rsp &
Step 10 At the Inventory Location screen, click OK.
Step 11 The Oracle Universal Installer screen appears and prompts you to run the /tmp/orainstRoot.sh script. Log into another terminal window as the root user and enter the following command:
Note The Installer does not prompt you to run the /tmp/orainstRoot.sh script if you have a previous version of Oracle installed on your workstation or if the /var/opt/oracle/oratab file already exists on your workstation.
Step 12 Enter the following command to run the orainstRoot.sh script:
Step 13 Return to the Oracle Universal Installer screen and click Continue.
Note The Oracle Universal Installer process might take up to 5 minutes.
Step 14 The Disk Location dialog box prompts you for disk two of the Oracle9i installation CDs. Return to the terminal window where you ran the ./runInstaller command and press Return on your keyboard to bring up the command prompt.
Step 15 Enter the following command at the command prompt:
Step 16 Remove disk one and insert disk two of the Oracle9i installation CDs.
Step 17 Minimize the terminal window.
Step 18 Return to the Disk Location dialog box and change the path to read as one of the following, depending on your Oracle version:
•For 32-bit Oracle, enter:
•For 64-bit Oracle, enter:
Click OK.
Step 19 The Disk Location dialog box prompts you for disk three of the Oracle9i installation CDs. Return to the terminal window where you ran the ./runInstaller command and press Return on your keyboard to bring up the command prompt.
Step 20 Enter the following command at the command prompt:
Step 21 Remove disk two and insert disk three of the Oracle9i installation CDs.
Step 22 Minimize the terminal window.
Step 23 Return to the Disk Location dialog box and change the path to read as one of the following, depending on your Oracle version:
•For 32-bit Oracle, enter:
•For 64-bit Oracle, enter:
Click OK.
Step 24 You are prompted to run /oraclesw9i/product/9.2/root.sh from another window. Log into another terminal window as the root user and enter the following command:
cd /oraclesw9i/product/9.2
Step 25 Enter the following command to run the root.sh script:
Step 26 At the prompt for the local bin directory, enter the following path in the root.sh script:
Note The /oraclesw9i/product/9.2/local/bin directory must be created before running the root.sh script.
/oraclesw9i/product/9.2/local/bin
Step 27 Return to the Oracle Setup Privileges screen and click OK.
Step 28 Enter the following command to eject the CD:
3.3.4 Downloading the Oracle Patch Installer
Note The Oracle patch installer is used to install additional Oracle patches. If you already installed the Oracle patch installer, you can skip this section.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 2617419.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download.
Step 8 In the list of patches returned, click the first patch, which has the latest release number.
Note Do not be concerned if the patch refers to a later version of Oracle.
Step 9 In the Patch 2617419 window, go to the Platform or Language field and choose Generic Platform (the default).
Step 10 Click Download.
Step 11 Save the patch to the /oraclesw9i/product/9.2 directory.
Step 12 Enter the following commands to change the patch ownership and unzip the patch:
chown oracle:dba /oraclesw9i/product/9.2/p2617419_10102_GENERIC.zip
cd /oraclesw9i/product/9.2
unzip p2617419_10102_GENERIC.zip
3.3.5 Downloading the 9.2.0.6 Patch for Oracle9i
If you already have the 9.2.0.6 patch for Oracle9i installed, you can skip this section. To find out which patches have been installed, enter the following commands as the oracle user:
cd $ORACLE_HOME/OPatch/
./opatch lsinventory -detail | grep -i "oracle9i patch"
The output shows:
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 3948480.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p3948480_9206_SOLARIS.zip. For 64-bit Oracle, download p3948480_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory.
Step 9 As the oracle user, enter one of the following sets of commands to prepare the patch set, depending on your Oracle version:
•For 32-bit Oracle, enter:
unzip p3948480_9206_SOLARIS.zip
•For 64-bit Oracle, enter:
unzip p3948480_9206_SOLARIS64.zip
3.3.6 Installing the 9.2.0.6 Patch for Oracle9i
Note If you already have the 9.2.0.6 patch for Oracle9i installed, you can skip this section.
Step 1 Insert disk one of the CTM installation CDs in the CD-ROM drive.
Step 2 Enter the following command to log into the database workstation as the oracle user:
Step 3 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 4 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 5 Depending on your Oracle version, enter one of the following sets of commands to install the 9.2.0.6 patch:
•For 32-bit Oracle, enter:
./runInstaller -responseFile /oraclesw9i/patchset.rsp
•For 64-bit Oracle, enter:
./runInstaller -responseFile /oraclesw9i/patchset_64bit.rsp
Note If the Disk Location screen pops up, click Cancel.
Step 6 At the prompt to run the root.sh script, log into another terminal window as the root user and enter the following commands:
cd /oraclesw9i/product/9.2
Step 7 After the script finishes running, return to the prompt popup window and click OK.
Step 8 Click Next.
Step 9 Enter the following commands to eject the CD:
Step 10 After the patch is installed, read the Oracle patch README.html file to carry out the post-installation steps and check any caveats associated with this patch.
Step 11 Depending on your Oracle version, enter one of the following sets of commands to remove the 9.2.0.6 patch installation files:
•For 32-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS.zip
rm -rf /oraclesw9i/README.html
•For 64-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS64.zip
rm -rf /oraclesw9i/README.html
3.3.7 Installing and Applying Additional Oracle Patches
Complete the following steps to install and apply additional required Oracle patches.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number field, enter 2733910.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p2733910_9206_SOLARIS.zip. For 64-bit Oracle, download p2733910_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Note The 32-bit patch 2733910 unzips to ./4092208. This is not an error.
Step 9 In the MetaLink window, click Patches.
Step 10 Click Simple Search.
Step 11 In the Search by Patch Number field, enter 4067938.
Step 12 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 13 Click Go.
Step 14 Click Download. For 32-bit Oracle, download p4067938_9206_SOLARIS.zip. For 64-bit Oracle, download p4067938_9206_SOLARIS64.zip.
Step 15 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 16 In the MetaLink window, click Patches.
Step 17 Click Simple Search.
Step 18 In the Search by Patch Number field, enter 4147836.
Step 19 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 20 Click Go.
Step 21 Click Download. For 32-bit Oracle, download p4147836_9206_SOLARIS.zip. For 64-bit Oracle, download p4147836_9206_SOLARIS64.zip.
Step 22 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 23 For 64-bit Oracle only, the opatch apply command might fail. If this happens, edit the $ORACLE_HOME/inventory/ContentsXML/oraclehomeproperties.xml file by changing <ARU_ID>453</ARU_ID> to <ARU_ID>23</ARU_ID>. This is a known Oracle bug.
Step 24 Depending on your configuration, enter one of the following sets of commands as the oracle user to change directories to the patch directory and apply the 2733910 patch (which unzips to 4092208 on a 32-bit workstation):
•For 32-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
•For 64-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 25 Enter the following commands to change directories to the patch directory and apply the 4067938 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 26 Enter the following commands to change directories to the patch directory and apply the 4147836 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 27 As the oracle user, enter the following commands to restart the CTM R4.7.x database and the Oracle listener:
3.3.8 Installing the CTM R6.0 Server and Database and Migrating Basic Data
Note Before installing the CTM database, verify that Oracle9i is installed in the /oraclesw9i directory.
To install the CTM server and database and migrate basic data, log in as the root user and complete the following steps:
Step 1 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 2 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 3 Insert the CTM Server Disk 1 installation CD and enter the following commands:
cdrom/cdrom0/Disk1/ctmsetup.sh
The setup program searches for Sun Microsystems JRE version 1.4.2_05 on your workstation.
Note If JRE is not installed, the setup program starts the Java installation program. Follow the prompts to install JRE. Enter yes at the following binary license code agreement prompt:
Do you agree to the above license terms? [yes or no]
Then, continue installing the CTM server and database.
Note If the required Solaris patches are missing, you must install them manually. Click Cancel; then, click Quit. Download the patches from SunSolve Online at http://sunsolve.sun.com. After you install the patches, continue installing the CTM server and database.
This website is Copyright © 2005, Sun Microsystems, Inc. All rights reserved.
Wait for up to 60 seconds while the following message appears:
Ctmsetup.sh is installing CTM server...
Step 4 Click Next at the Introduction screen.
Step 5 At the License Agreement screen, read the license agreement and click the I accept the terms of the license agreement radio button. Click Next.
Step 6 At the Installation Options screen, choose Upgrade from existing CTM release; then, click Next.
Step 7 At the Database Migration Information screen, confirm the migration details and click Next.
Step 8 At the Select Products screen, check the Install Cisco Transport Manager Server check box; then, click Next.
Note The Install Web Server check box is selected automatically when you choose Install Cisco Transport Manager Server. The Install Web Server option allows you to use an HTTP connection to download files from the CTM server to the CTM client. The web server is also used to launch the online help and CiscoView, which is an application used by CTM to configure and monitor ONS 155xx NEs. The web server is required for the CTM server.
Caution Do not check the other check boxes on the Select Products screen.
Note When you choose Install Cisco Transport Manager Server, the High Availability Installation option becomes available. This option applies only to HA installations. Do not choose it. To install HA, refer to Cisco Transport Manager High Availability Installation Guide for CTM R6.0.
Note The license for CTM GateWay/CORBA is sold separately. If you are using this feature in a production environment, you must purchase a license. You can install CTM GateWay/CORBA when you install the CTM server; however, this section assumes that you are installing the two products separately. For more information, see Chapter 4, "Installing CTM GateWay/CORBA R6.0."
Note The license for CiscoView is sold separately if used to manage the ONS 15530, ONS 15540 ESP, or ONS 15540 ESPx. If you are using this feature in a production environment to manage the ONS 15530, ONS 15540 ESP, or ONS 15540 ESPx, you must purchase a license for LAN Management Solution (LMS) Release 2.5, which includes CiscoView.
The license for CiscoView is bundled with CTM if used to manage the ONS 15501 DC or AC. You do not need to purchase a separate CiscoView license to manage the ONS 15501 DC or AC.
If you check the Install CiscoView Server check box, you receive the following prompt:
CiscoView installation has been moved to CTM Server Disk 3. After CTM server has been installed, insert the CTM Server Disk 3 and run the './installCiscoView.sh' script.
You must install the CTM server before you can install CiscoView. After installing the CTM server, see Chapter 6, "Installing and Setting Up CiscoView."
Step 9 At the CTM Group Information & Sudo Installation screen, complete the following substeps:
a. Enter the name of the UNIX group to which you want to assign administrator privileges.
b. To install sudo, check the Install CTM Sudo check box. If you do not want to install sudo, uncheck the check box.
c. Click Next.
Note For information about the sudo feature, see 1.4.1 Overview of Sudo Commands, page 1-12.
Step 10 At the FTP Information screen, complete the following substeps to configure an FTP account for ONS 15216 EDFA3 software download operations:
a. Enter the following information:
•FTP username
•FTP user password
•Confirm FTP user password
•FTP directory
b. Check or uncheck the Create new FTP Account check box. If checked, the FTP user will be created automatically on the CTM server workstation by the install script. If unchecked, it is assumed that an FTP user already exists on the CTM server workstation.
c. Click Next.
Note The FTP information that you enter during the CTM server installation can be modified later from the CTM client Control Panel window. Refer to Cisco Transport Manager Release 6.0 User Guide for more information.
Step 11 At the Main Options screen, complete the following substeps:
a. Check the Create CTM database check box and specify the Oracle SID. The default is CTM.
b. Check the Install CTM server check box.
Caution Uncheck the
Check System Settings check box. Leave the
Migrate historical data check box unchecked.
c. Click Next.
Step 12 At the Server IP Address screen, specify an IP address for the CTM server; then, click Next.
Step 13 At the Select Network Configuration screen, specify the size of your network; then, click Next.
Note If you installed Oracle Standard Edition, you can only choose Small.
Step 14 At the Configure TFTP Server screen, complete the following substeps if you want to enable TFTP for the ONS 15216 EDFA2, ONS 15501, ONS 15530, and ONS 15540:
a. Check the Enable TFTP Server check box.
b. Enter the TFTP directory name. The default is /tftpboot.
c. Click Next.
Step 15 At the Database Information screen, specify the IP address of the database workstation and specify whether or not you want to install the database in ARCHIVELOG mode. Click Next.
Step 16 At the CTM Database Installation Directories screen, the setup program verifies that the directories exist as recommended in Table 3-1. Click Next.
Step 17 The Migrate CTM Data screen appears with the following messages:
Do you want to migrate CTM data?
Do you want to migrate GateWay CORBA data?
Log into another terminal window as the root user and enter the following command to stop the server, if it is running:
Step 18 Return to the Migrate CTM Data screen and complete the following substeps:
a. Click Yes to migrate CTM data.
b. Click Yes or No to migrate CTM GateWay/CORBA data, depending on your configuration.
Note If you want to migrate CTM GateWay/CORBA data, you must click Yes at this point. You cannot migrate CTM GateWay/CORBA data later.
c. Specify the IP address or hostname of the database server that you are migrating data from.
d. Enter the password for the ctmanager oracle user. (Use the password of the database you are migrating from; the default is ctm123!.)
e. Click Next.
Note If you entered a hostname, the setup program automatically translates the hostname to a physical IP address and prompts you to confirm the address. Click Yes.
Step 19 At the Destination Folder screen, specify where you want to install the CTM server. The default directory is /opt/CiscoTransportManagerServer. You can click Change to choose a different destination. After you specify your destination, click Next.
Note If the destination directory that you specified is a new directory, you will receive the message "Specified directory does not exist, create it?" Click Yes.
Caution CTM checks for the /opt/CiscoTransportManagerServer directory or a symbolic link to it. If CTM cannot find the /opt/CiscoTransportManagerServer directory or a symbolic link, CTM creates a symbolic link automatically. Therefore, do not delete any instances of /opt/CiscoTransportManagerServer from your CTM file structure.
Step 20 The Pre-Installation Summary screen shows the items that will be installed. Click Install.
Note It might take 30 to 60 minutes or longer to migrate basic data, depending on your system performance and on the amount of data that you are migrating.
Step 21 At the Insert New Media screen, complete the following substeps:
a. Eject the CTM Server Disk 1 installation CD, insert the CTM Server Disk 2 installation CD, and click Browse.
b. The Select a Folder dialog box opens. Double-click cdrom; then, single-click cdrom0. The filename text box now reads /cdrom/cdrom0.
c. In the Select a Folder dialog box, click Select.
d. In the Insert New Media screen, click OK.
Step 22 The Web Server Installation Summary screen summarizes the results of the web server installation. Click Next.
Step 23 The Install Complete screen summarizes the results of the installation. Click Done.
Step 24 Enter the following command to reboot the system. The CTM server starts automatically after rebooting:
Step 25 To verify that the CTM R6.0 server is running, enter the showctm command after the server reboots. The showctm command displays the CTM server version running as 6.0, followed by the build number. In the output, you will see two instances of "CTMServer," "SnmpTrapService," "SMService," and "Apache Web Server." This indicates that the CTM server is running. You should also see NE-specific processes, depending on your network. You might also see CTM GateWay/CORBA and CTM GateWay/TL1 instances.
3.3.9 Copying the Client Upgrade Files After the CTM Server Installation
You have two options for upgrading each client installation to the latest version of CTM that is on the server. You can choose to:
•Manually upgrade each client installation. If you have a previously installed version of the CTM client, you must delete the directory where the previous client is installed before installing the CTM R6.0 client. See 5.1 Installing the CTM Client and Cisco Edge Craft on Microsoft Windows, page 5-2 or 5.4 Installing the CTM Client and Cisco Edge Craft on Sun Solaris, page 5-6 for more information.
•Automatically upgrade each client when it connects to a server. During login, if the CTM client software version is older than the CTM server software version, the client will be prompted for upgrade. See 5.2 Starting the CTM Client in Microsoft Windows, page 5-5 or 5.5 Starting the CTM Client in Sun Solaris, page 5-8 for more information.
For this option you must copy the client installation files to the server. The CTM client and server installation files reside on separate installation CDs. To copy the client installation files to the server, you must eject the CTM server CD, insert the CTM client CD, and run an automated script, CopyUpgradeFiles.sh, to copy the client installation files to a specific folder under the CTM server installation directory. To do this, log in as the root user and complete the following steps.
Note The CTM server must be installed before completing the following steps.
Step 1 Enter the following commands to eject the CTM server installation CD:
Step 2 Insert the CTM client installation CD and enter the following commands:
3.4 Upgrading from CTM R4.7.x and Oracle8i to CTM R6.0 and Oracle9i on Separate Workstations
This section describes how to upgrade from CTM R4.7.x and Oracle8i to CTM R6.0 and Oracle9i when you are installing the CTM R6.0 server and the Oracle9i database on separate Sun Solaris 8 servers.
Caution Before upgrading your database to CTM R6.0, it is strongly recommended that you back up your CTM R4.7.x database. If you do so, you can revert to your old data in the event that the upgrade fails. To back up the database, see
Cisco Transport Manager Release 6.0 User Guide, which is available online at
http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/optnet/ctm/index.htm. Refer to the section "Backing Up the CTM Database from the CTM GUI."
Note The C shell is assumed for all UNIX commands.
3.4.1 Setting the Environment for Installation on the CTM Database Workstation
To set the environment for installation, log into the database server as the root user and complete the following steps:
Step 1 Enter the following command to verify that the disk directories shown in Table 3-2 exist:
Table 3-2 Disk Directories
Directory
|
Contents
|
/db01
|
For the system tablespace used by Oracle
|
/db02
|
For the basedata tablespace, the alarmdata tablespace, the eventdata tablespace used by CTM, and the system tablespace used by Oracle
|
/db03
|
For the data tablespace used by CTM
|
/db04
|
For the INDEX tablespace used by CTM
|
/db051
|
For the archived logs
|
/ctm_backup2
|
For the backed-up database and configuration files
|
/oraclesw9i
|
For the Oracle software
|
/tftpboot
|
For the TFTP directory
Note Disk partitioning is not required for /tftpboot, but the directory is required.
|
Step 2 Enter the following command to modify the password file:
Step 3 Navigate to the entry that looks similar to the following:
oracle:x:100:3303::/oraclesw:/bin/csh
Step 4 In the entry, change /oraclesw to /oraclesw9i. The entry should now look similar to the following:
oracle:x:100:3303::/oraclesw9i:/bin/csh
Step 5 Enter the following command to save the changes:
3.4.2 Installing the Oracle9i Software on the CTM Database Workstation
Step 1 Insert the CTM Server Disk 1 installation CD and enter the following command:
Step 2 Enter the following command to list the files in the cdrom/cdrom0/Disk1 directory:
Note If a list of files is returned, it indicates that you can access the CD-ROM successfully. If no files are visible, or if an error message is returned, refer to Sun Solaris documentation for mounting the CD-ROM.
Step 3 Enter the following command to copy the default profile to the Oracle home directory:
cp /cdrom/cdrom0/Disk1/InstData/Solaris/VM/cfg/{small | medium | large | highend}/.cshrc
/oraclesw9i/.cshrc
For example, to copy the default profile for a small network, enter:
cp /cdrom/cdrom0/Disk1/InstData/Solaris/VM/cfg/small/.cshrc /oraclesw9i/.cshrc
Note If you installed Oracle Standard Edition, you must copy the default profile for a small network.
Step 4 Enter the following command to determine what type of applications you can run on your OS:
If the output reads "64-bit sparcv9 kernel modules," you can run both 64-bit and 32-bit applications. If the output reads "32-bit sparcv9 kernel modules," you can run only 32-bit applications.
Note It is recommended that you be able to run both 64-bit and 32-bit applications.
Step 5 Complete one of the following options, depending on your Oracle version:
•If you are installing 32-bit Oracle Enterprise Edition, enter:
cp /cdrom/cdrom0/Disk1/svrcustom.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset.rsp /oraclesw9i
•If you are installing 64-bit Oracle Enterprise Edition, enter:
cp /cdrom/cdrom0/Disk1/svrcustom_64bit.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset_64bit.rsp /oraclesw9i
•If you are installing 32-bit Oracle Standard Edition, enter:
cp /cdrom/cdrom0/Disk1/svrcustom_std.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset.rsp /oraclesw9i
•If you are installing 64-bit Oracle Standard Edition, enter:
cp /cdrom/cdrom0/Disk1/svrcustom_std_64bit.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset_64bit.rsp /oraclesw9i
Step 6 (Optional) Enter the following commands to change ownership of the Oracle software directories:
/usr/bin/chown -R oracle:dba /oraclesw9i
/usr/bin/chown -R oracle:dba /db01
/usr/bin/chown -R oracle:dba /db02
/usr/bin/chown -R oracle:dba /db03
/usr/bin/chown -R oracle:dba /db04
/usr/bin/chown -R oracle:dba /db05
/usr/bin/chown -R oracle:dba /ctm_backup
Step 7 Enter the following commands to eject the CTM Server Disk 1 installation CD:
Step 8 If you are using an xterm window or a remote host, enter the following command to enable the xterm connection from the clients:
3.4.3 Installing the Oracle9i Software with the .rsp Response File Provided by Cisco on the CTM Database Workstation
Step 1 Complete the following substeps to shut down all of the CTM clients:
a. In the Domain Explorer window, choose Administration > CTM Users.
b. In the CTM Users table, choose Administration > Logged In CTM Users.
c. In the Logged In CTM Users table, select the user whose session will be ended and choose Administration > Log Out User (or click the Log Out User tool).
d. Click Yes at the following prompt:
This operation will log out the selected CTM user. The process will take approximately
1 minute and this CTM client will be unusable until then. Do you wish to continue?
Wait while the CTM server logs out the selected CTM client. The CTM GUI is frozen for approximately 1 minute until the request is complete.
Step 2 As the root user, enter the following command to stop the workstation where the CTM server is running:
Step 3 Enter the following command to remove the oraInst.loc file, if it exists:
rm /var/opt/oracle/oraInst.loc
Step 4 On the workstation where the CTM database is running, enter the following commands to stop the Oracle listener and shut down all Oracle processes, if they are running:
Step 5 Enter the following command to log in as the oracle user:
Tip To verify the username, enter the id command.
Step 6 Insert disk one of the Oracle9i installation CDs in the CD-ROM drive.
Step 7 Enter the following command to set the display on your terminal:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 8 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 9 Complete one of the following options, depending on your Oracle version:
•If you are installing 32-bit Oracle Enterprise Edition, enter the following command to start the Oracle Installer:
./runInstaller -responseFile /oraclesw9i/svrcustom.rsp &
•If you are installing 64-bit Oracle Enterprise Edition, enter the following command to start the Oracle Installer:
./runInstaller -responseFile /oraclesw9i/svrcustom_64bit.rsp &
•If you are installing 32-bit Oracle Standard Edition, enter the following command to start the Oracle Installer:
./runInstaller -responseFile /oraclesw9i/svrcustom_std.rsp &
•If you are installing 64-bit Oracle Standard Edition, enter the following command to start the Oracle Installer:
./runInstaller -responseFile /oraclesw9i/svrcustom_std_64bit.rsp &
Step 10 At the Inventory Location screen, click OK.
Step 11 The Oracle Universal Installer screen appears and prompts you to run the /tmp/orainstRoot.sh script. Log into another terminal window as the root user and enter the following command:
Note The Installer does not prompt you to run the /tmp/orainstRoot.sh script if you have a previous version of Oracle installed on your workstation or if the /var/opt/oracle/oratab file already exists on your workstation.
Step 12 Enter the following command to run the orainstRoot.sh script:
Step 13 Return to the Oracle Universal Installer screen and click Continue.
Note The Oracle Universal Installer process might take up to 5 minutes.
Step 14 The Disk Location dialog box prompts you for disk two of the Oracle9i installation CDs. Return to the terminal window where you ran the ./runInstaller command and press Return on your keyboard to bring up the command prompt.
Step 15 Enter the following command at the command prompt:
Step 16 Remove disk one and insert disk two of the Oracle9i installation CDs.
Step 17 Minimize the terminal window.
Step 18 Return to the Disk Location dialog box and change the path to read as one of the following, depending on your Oracle version:
•For 32-bit Oracle, enter:
•For 64-bit Oracle, enter:
Click OK.
Step 19 The Disk Location dialog box prompts you for disk three of the Oracle9i installation CDs. Return to the terminal window where you ran the ./runInstaller command and press Return on your keyboard to bring up the command prompt.
Step 20 Enter the following command at the command prompt:
Step 21 Remove disk two and insert disk three of the Oracle9i installation CDs.
Step 22 Minimize the terminal window.
Step 23 Return to the Disk Location dialog box and change the path to read as one of the following, depending on your Oracle version:
•For 32-bit Oracle, enter:
•For 64-bit Oracle, enter:
Click OK.
Step 24 You are prompted to run /oraclesw9i/product/9.2/root.sh from another window. Log into another terminal window as the root user and enter the following command:
cd /oraclesw9i/product/9.2
Step 25 Enter the following command to run the root.sh script:
Step 26 At the prompt for the local bin directory, enter the following path in the root.sh script:
Note The /oraclesw9i/product/9.2/local/bin directory must be created before running the root.sh script.
/oraclesw9i/product/9.2/local/bin
Step 27 Return to the Oracle Setup Privileges screen and click OK.
Step 28 Enter the following command to eject the CD:
3.4.4 Downloading the Oracle Patch Installer on the CTM Database Workstation
Note The Oracle patch installer is used to install additional Oracle patches. If you already installed the Oracle patch installer, you can skip this section.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 2617419.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download.
Step 8 In the list of patches returned, click the first patch, which has the latest release number.
Note Do not be concerned if the patch refers to a later version of Oracle.
Step 9 In the Patch 2617419 window, go to the Platform or Language field and choose Generic Platform (the default).
Step 10 Click Download.
Step 11 Save the patch to the /oraclesw9i/product/9.2 directory.
Step 12 Enter the following commands to change the patch ownership and unzip the patch:
chown oracle:dba /oraclesw9i/product/9.2/p2617419_10102_GENERIC.zip
cd /oraclesw9i/product/9.2
unzip p2617419_10102_GENERIC.zip
3.4.5 Downloading the 9.2.0.6 Patch for Oracle9i on the CTM Database Workstation
If you already have the 9.2.0.6 patch for Oracle9i installed, you can skip this section. To find out which patches have been installed, enter the following commands as the oracle user:
cd $ORACLE_HOME/OPatch/
./opatch lsinventory -detail | grep -i "oracle9i patch"
The output shows:
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 3948480.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p3948480_9206_SOLARIS.zip. For 64-bit Oracle, download p3948480_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory.
Step 9 As the oracle user, enter one of the following sets of commands to prepare the patch set, depending on your Oracle version:
•For 32-bit Oracle, enter:
unzip p3948480_9206_SOLARIS.zip
•For 64-bit Oracle, enter:
unzip p3948480_9206_SOLARIS64.zip
3.4.6 Installing the 9.2.0.6 Patch for Oracle9i on the CTM Database Workstation
Note If you already have the 9.2.0.6 patch for Oracle9i installed, you can skip this section.
Step 1 Insert disk one of the CTM installation CDs in the CD-ROM drive.
Step 2 Enter the following command to log into the database workstation as the oracle user:
Step 3 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 4 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 5 Depending on your Oracle version, enter one of the following sets of commands to install the 9.2.0.6 patch:
•For 32-bit Oracle, enter:
./runInstaller -responseFile /oraclesw9i/patchset.rsp
•For 64-bit Oracle, enter:
./runInstaller -responseFile /oraclesw9i/patchset_64bit.rsp
Note If the Disk Location screen pops up, click Cancel.
Step 6 At the prompt to run the root.sh script, log into another terminal window as the root user and enter the following commands:
cd /oraclesw9i/product/9.2
Step 7 After the script finishes running, return to the prompt popup window and click OK.
Step 8 Click Next.
Step 9 Enter the following commands to eject the CD:
Step 10 After the patch is installed, read the Oracle patch README.html file to carry out the post-installation steps and check any caveats associated with this patch.
Step 11 Depending on your Oracle version, enter one of the following sets of commands to remove the 9.2.0.6 patch installation files:
•For 32-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS.zip
rm -rf /oraclesw9i/README.html
•For 64-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS64.zip
rm -rf /oraclesw9i/README.html
3.4.7 Installing and Applying Additional Oracle Patches on the CTM Database Workstation
Complete the following steps to install and apply additional required Oracle patches.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number field, enter 2733910.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p2733910_9206_SOLARIS.zip. For 64-bit Oracle, download p2733910_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Note The 32-bit patch 2733910 unzips to ./4092208. This is not an error.
Step 9 In the MetaLink window, click Patches.
Step 10 Click Simple Search.
Step 11 In the Search by Patch Number field, enter 4067938.
Step 12 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 13 Click Go.
Step 14 Click Download. For 32-bit Oracle, download p4067938_9206_SOLARIS.zip. For 64-bit Oracle, download p4067938_9206_SOLARIS64.zip.
Step 15 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 16 In the MetaLink window, click Patches.
Step 17 Click Simple Search.
Step 18 In the Search by Patch Number field, enter 4147836.
Step 19 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 20 Click Go.
Step 21 Click Download. For 32-bit Oracle, download p4147836_9206_SOLARIS.zip. For 64-bit Oracle, download p4147836_9206_SOLARIS64.zip.
Step 22 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 23 For 64-bit Oracle only, the opatch apply command might fail. If this happens, edit the $ORACLE_HOME/inventory/ContentsXML/oraclehomeproperties.xml file by changing <ARU_ID>453</ARU_ID> to <ARU_ID>23</ARU_ID>. This is a known Oracle bug.
Step 24 Depending on your configuration, enter one of the following sets of commands as the oracle user to change directories to the patch directory and apply the 2733910 patch (which unzips to 4092208 on a 32-bit workstation):
•For 32-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
•For 64-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 25 Enter the following commands to change directories to the patch directory and apply the 4067938 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 26 Enter the following commands to change directories to the patch directory and apply the 4147836 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 27 As the oracle user, enter the following commands to restart the CTM R4.7.x database and the Oracle listener:
3.4.8 Installing the CTM R6.0 Database and Migrating Basic Data on the CTM Database Workstation
Note Before installing the CTM database, verify that Oracle9i is installed in the /oraclesw9i directory.
To install the CTM R6.0 database and migrate basic data, log into the database server as the root user and complete the following steps:
Step 1 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 2 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 3 Insert the CTM Server Disk 1 installation CD and enter the following commands:
cdrom/cdrom0/Disk1/ctmsetup.sh
The setup program searches for Sun Microsystems JRE version 1.4.2_05 on your workstation.
Note If JRE is not installed, the setup program starts the Java installation program. Follow the prompts to install JRE. Enter yes at the following binary license code agreement prompt:
Do you agree to the above license terms? [yes or no]
Then, continue installing the CTM database.
Note If the required Solaris patches are missing, you must install them manually. Click Cancel; then, click Quit. Download the patches from SunSolve Online at http://sunsolve.sun.com. After you install the patches, continue installing the CTM database.
This website is Copyright © 2005, Sun Microsystems, Inc. All rights reserved.
Wait for up to 60 seconds while the following message appears:
Ctmsetup.sh is installing CTM server...
Step 4 Click Next at the Introduction screen.
Step 5 At the License Agreement screen, read the license agreement and click the I accept the terms of the license agreement radio button. Click Next.
Step 6 At the Installation Options screen, choose Upgrade from existing CTM release; then, click Next.
Step 7 At the Database Migration Information screen, confirm the migration details; then, click Next.
Step 8 At the Select Products screen, check the Install Cisco Transport Manager Server check box; then, click Next.
Note The Install Web Server check box is selected automatically when you choose Install Cisco Transport Manager Server. The Install Web Server option allows you to use an HTTP connection to download files from the CTM server to the CTM client. The web server is also used to launch the online help and CiscoView, which is an application used by CTM to configure and monitor ONS 155xx NEs. The web server is required for the CTM server.
Caution Do not check the other check boxes on the Select Products screen.
Note When you choose Install Cisco Transport Manager Server, the High Availability Installation option becomes available. This option applies only to HA installations. Do not choose it. To install HA, refer to Cisco Transport Manager High Availability Installation Guide for CTM R6.0.
Note The license for CTM GateWay/CORBA is sold separately. If you are using this feature in a production environment, you must purchase a license. You can install CTM GateWay/CORBA when you install the CTM server; however, this section assumes that you are installing the two products separately. For more information, see Chapter 4, "Installing CTM GateWay/CORBA R6.0."
Note The license for CiscoView is sold separately if used to manage the ONS 15530, ONS 15540 ESP, or ONS 15540 ESPx. If you are using this feature in a production environment to manage the ONS 15530, ONS 15540 ESP, or ONS 15540 ESPx, you must purchase a license for LAN Management Solution (LMS) Release 2.5, which includes CiscoView.
The license for CiscoView is bundled with CTM if used to manage the ONS 15501 DC or AC. You do not need to purchase a separate CiscoView license to manage the ONS 15501 DC or AC.
If you check the Install CiscoView Server check box, you receive the following prompt:
CiscoView installation has been moved to CTM Server Disk 3. After CTM server has been installed, insert the CTM Server Disk 3 and run the './installCiscoView.sh' script.
You must install the CTM server before you can install CiscoView. After installing the CTM server, see Chapter 6, "Installing and Setting Up CiscoView."
Step 9 At the CTM Group Information & Sudo Installation screen, complete the following substeps:
a. Enter the name of the UNIX group to which you want to assign administrator privileges.
b. To install sudo, check the Install CTM Sudo check box. If you do not want to install sudo, uncheck the check box.
c. Click Next.
Note For information about the sudo feature, see 1.4.1 Overview of Sudo Commands, page 1-12.
Step 10 At the FTP Information screen, accept the default selections; then, click Next.
Step 11 At the Main Options screen, check only the Create CTM database check box and specify the Oracle SID. (The default is CTM.) Click Next.
Caution Be sure to uncheck the other check boxes on the Main Options screen.
Step 12 At the Specify CTM Server IP Address screen, enter the IP address or hostname of the workstation where the CTM server will run; then, click Next.
Note If you entered a hostname, the setup program automatically translates the hostname to a physical IP address and prompts you to confirm the address. Click Yes.
Step 13 At the Select Network Configuration screen, specify the size of your network; then, click Next.
Note If you installed Oracle Standard Edition, you can only choose Small.
Step 14 At the Database Information screen, specify the IP address of the database workstation and specify whether or not you want to install the database in ARCHIVELOG mode. Click Next.
Step 15 At the CTM Database Installation Directories screen, the setup program verifies that the directories exist as recommended in Table 3-2. Click Next.
Step 16 The Migrate CTM Data screen appears with the following messages:
Do you want to migrate CTM data?
Do you want to migrate GateWay CORBA data?
As the root user, log into a terminal window on the CTM server and enter the following command to stop the previous version of the CTM server:
Step 17 Return to the Migrate CTM Data screen and complete the following substeps:
a. Click Yes to migrate CTM data.
b. Click Yes or No to migrate CTM GateWay/CORBA data, depending on your configuration.
Note If you want to migrate CTM GateWay/CORBA data, you must click Yes at this point. You cannot migrate CTM GateWay/CORBA data later.
c. Specify the IP address or hostname of the database server that you are migrating data from.
d. Enter the password for the ctmanager oracle user. (Use the password of the database you are migrating from; the default is ctm123!.)
e. Click Next.
Note If you entered a hostname, the setup program automatically translates the hostname to a physical IP address and prompts you to confirm the address. Click Yes.
Step 18 At the Pre-Installation Summary screen, click Install to create the CTM database and migrate basic data.
Note It might take 30 to 60 minutes or longer to migrate basic data, depending on your system performance and on the amount of data that you are migrating.
Step 19 At the Insert New Media screen, complete the following substeps:
a. Eject the CTM Server Disk 1 installation CD, insert the CTM Server Disk 2 installation CD, and click Browse.
b. The Select a Folder dialog box opens. Double-click cdrom; then, single-click cdrom0. The filename text box now reads /cdrom/cdrom0.
c. In the Select a Folder dialog box, click Select.
d. In the Insert New Media screen, click OK.
Step 20 The Install Complete screen summarizes the results of the installation. Click Done.
3.4.9 Installing the Oracle9i Client on the CTM Server Workstation
This section describes how to install the Oracle9i client software on a Sun Solaris 8 server to meet the CTM server requirements for a remote database configuration.
Log in as the root user on the workstation where the CTM server will run and complete the following steps:
Step 1 Enter the following command to verify that the disk directories shown in Table 3-3 exist:
Table 3-3 Disk Directories
Directory
|
Contents
|
/ctm_backup1
|
For the backed-up configuration files
|
/oraclesw9i
|
For the Oracle software
|
/tftpboot
|
For the TFTP directory
Note Disk partitioning is not required for /tftpboot, but the directory is required.
|
Step 2 Enter the following command to modify the password file:
Step 3 Navigate to the entry that looks similar to the following:
oracle:x:100:3303::/oraclesw:/bin/csh
Step 4 In the entry, change /oraclesw to /oraclesw9i. The entry should now look similar to the following:
oracle:x:100:3303::/oraclesw9i:/bin/csh
Step 5 Enter the following command to save the changes:
Step 6 Enter the following commands to create a soft link to use your existing partitions:
ln -s /<partition_name_1> /ctm_backup
ln -s /<partition_name_2> /oraclesw9i
Step 7 Enter the following command to enable the xterm connection from the clients:
Step 8 Insert the CTM Server Disk 1 installation CD.
Step 9 Enter the following command to copy the default profile to the Oracle home directory:
cp /cdrom/cdrom0/Disk1/InstData/Solaris/VM/cfg/{small | medium | large | highend}/.cshrc
/oraclesw9i/.cshrc
For example, to copy the default profile for a small network, enter:
cp /cdrom/cdrom0/Disk1/InstData/Solaris/VM/cfg/small/.cshrc /oraclesw9i/.cshrc
Step 10 Complete one of the following options, depending on your Oracle version:
•If you are installing 32-bit Oracle Enterprise Edition, enter the following command to copy the clientcustom.rsp response file to your workstation:
cp /cdrom/cdrom0/Disk1/clientcustom.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset.rsp /oraclesw9i
•If you are installing 64-bit Oracle Enterprise Edition, enter the following command to copy the clientcustom_64bit.rsp response file to your workstation:
cp /cdrom/cdrom0/Disk1/clientcustom_64bit.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset_64bit.rsp /oraclesw9i
•If you are installing 32-bit Oracle Standard Edition, enter the following command to copy the clientcustom_std.rsp response file to your workstation:
cp /cdrom/cdrom0/Disk1/clientcustom_std.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset.rsp /oraclesw9i
•If you are installing 64-bit Oracle Standard Edition, enter the following command to copy the clientcustom_std_64bit.rsp response file to your workstation:
cp /cdrom/cdrom0/Disk1/clientcustom_std_64bit.rsp /oraclesw9i
cp /cdrom/cdrom0/Disk1/patchset_64bit.rsp /oraclesw9i
Step 11 Enter the following commands to change ownership of the Oracle software directories:
/usr/bin/chown -R oracle:dba /oraclesw9i
/usr/bin/chown -R oracle:dba /ctm_backup
Step 12 Enter the following commands to eject the CTM Server Disk 1 installation CD:
Step 13 Enter the following command to remove the oraInst.loc file, if it exists:
rm /var/opt/oracle/oraInst.loc
Step 14 Enter the following command to log in as the oracle user:
Tip To verify the username, enter the id command.
Step 15 Insert disk one of the Oracle9i installation CDs.
Step 16 Enter the following command to set the display on your terminal:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 17 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 18 Enter the following command to point to the cdrom/cdrom0 directory:
Step 19 Depending on your Oracle version, complete one of the following options to install the Oracle client:
•If you are installing 32-bit Oracle Enterprise Edition, enter:
./runInstaller -responseFile /oraclesw9i/clientcustom.rsp
•If you are installing 64-bit Oracle Enterprise Edition, enter:
./runInstaller -responseFile /oraclesw9i/clientcustom_64bit.rsp
•If you are installing 32-bit Oracle Standard Edition, enter:
./runInstaller -responseFile /oraclesw9i/clientcustom_std.rsp
•If you are installing 64-bit Oracle Standard Edition, enter:
./runInstaller -responseFile /oraclesw9i/clientcustom_std_64bit.rsp
Step 20 The Oracle Universal Installer screen prompts you to run the /tmp/orainstRoot.sh script. Log into another terminal window as the root user and enter the following command:
Note The Installer does not prompt you to run the /tmp/orainstRoot.sh script if you have a previous version of Oracle installed on your workstation or if the /var/opt/oracle/oratab file already exists on your workstation.
Step 21 Enter the following command to run the orainstRoot.sh script:
Step 22 Return to the Oracle Universal Installer screen and click Continue.
Note The Oracle Universal Installer process might take up to 5 minutes.
Step 23 You are prompted to run /oraclesw9i/product/9.2/root.sh from another window. Log into another terminal window as the root user and enter the following command:
cd /oraclesw9i/product/9.2
Step 24 Enter the following command to run the root.sh script:
Step 25 At the prompt for the local bin directory, enter the following command in the root.sh script:
/oraclesw9i/product/9.2/local/bin
Step 26 Return to the Oracle Setup Privileges screen and click OK.
Step 27 Enter the following commands to eject the CD:
3.4.9.1 Downloading the Oracle Patch Installer on the CTM Server Workstation
Note The Oracle patch installer is used to install additional Oracle patches. If you already installed the Oracle patch installer, you can skip this section.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 2617419.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download.
Step 8 In the list of patches returned, click the first patch, which has the latest release number.
Note Do not be concerned if the patch refers to a later version of Oracle.
Step 9 In the Patch 2617419 window, go to the Platform or Language field and choose Generic Platform (the default).
Step 10 Click Download.
Step 11 Save the patch to the /oraclesw9i/product/9.2 directory.
Step 12 Enter the following commands to change the patch ownership and unzip the patch:
chown oracle:dba /oraclesw9i/product/9.2/p2617419_10102_GENERIC.zip
cd /oraclesw9i/product/9.2
unzip p2617419_10102_GENERIC.zip
3.4.9.2 Downloading the 9.2.0.6 Patch for Oracle9i on the CTM Server Workstation
Note If you already have the 9.2.0.6 patch for Oracle9i installed, you can skip this section.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 3948480.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p3948480_9206_SOLARIS.zip. For 64-bit Oracle, download p3948480_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory.
Step 9 As the oracle user, enter one of the following sets of commands to prepare the patch set, depending on your Oracle version:
•For 32-bit Oracle, enter:
unzip p3948480_9206_SOLARIS.zip
•For 64-bit Oracle, enter:
unzip p3948480_9206_SOLARIS64.zip
3.4.9.3 Installing the 9.2.0.6 Patch for Oracle9i on the CTM Server Workstation
Step 1 Insert disk one of the CTM installation CDs in the CD-ROM drive.
Step 2 Enter the following command to log into the database workstation as the oracle user:
Step 3 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 4 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 5 Depending on your Oracle version, enter one of the following sets of commands to install the 9.2.0.6 patch:
•For 32-bit Oracle, enter:
./runInstaller -responseFile /oraclesw9i/patchset.rsp
•For 64-bit Oracle, enter:
./runInstaller -responseFile /oraclesw9i/patchset_64bit.rsp
Note If the Disk Location screen pops up, click Cancel.
Step 6 At the prompt to run the root.sh script, log into another terminal window as the root user and enter the following commands:
cd /oraclesw9i/product/9.2
Step 7 After the script finishes running, return to the prompt popup window and click OK.
Step 8 Click Next.
Step 9 Enter the following commands to eject the CD:
Step 10 After the patch is installed, read the Oracle patch README.html file to carry out the post-installation steps and check any caveats associated with this patch.
Step 11 Depending on your Oracle version, enter one of the following sets of commands to remove the 9.2.0.6 patch installation files:
•For 32-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS.zip
rm -rf /oraclesw9i/README.html
•For 64-bit Oracle, enter:
rm -rf /oraclesw9i/p3948480_9206_SOLARIS64.zip
rm -rf /oraclesw9i/README.html
3.4.9.4 Installing and Applying Additional Oracle Patches on the CTM Server Workstation
Complete the following steps to install and apply additional required Oracle patches.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number field, enter 2733910.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 32-bit Oracle, download p2733910_9206_SOLARIS.zip. For 64-bit Oracle, download p2733910_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Note The 32-bit patch 2733910 unzips to ./4092208. This is not an error.
Step 9 In the MetaLink window, click Patches.
Step 10 Click Simple Search.
Step 11 In the Search by Patch Number field, enter 4067938.
Step 12 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 13 Click Go.
Step 14 Click Download. For 32-bit Oracle, download p4067938_9206_SOLARIS.zip. For 64-bit Oracle, download p4067938_9206_SOLARIS64.zip.
Step 15 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 16 In the MetaLink window, click Patches.
Step 17 Click Simple Search.
Step 18 In the Search by Patch Number field, enter 4147836.
Step 19 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 20 Click Go.
Step 21 Click Download. For 32-bit Oracle, download p4147836_9206_SOLARIS.zip. For 64-bit Oracle, download p4147836_9206_SOLARIS64.zip.
Step 22 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 23 For 64-bit Oracle only, the opatch apply command might fail. If this happens, edit the $ORACLE_HOME/inventory/ContentsXML/oraclehomeproperties.xml file by changing <ARU_ID>453</ARU_ID> to <ARU_ID>23</ARU_ID>. This is a known Oracle bug.
Step 24 Depending on your configuration, enter one of the following sets of commands as the oracle user to change directories to the patch directory and apply the 2733910 patch (which unzips to 4092208 on a 32-bit workstation):
•For 32-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
•For 64-bit, enter:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 25 Enter the following commands to change directories to the patch directory and apply the 4067938 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
Step 26 Enter the following commands to change directories to the patch directory and apply the 4147836 patch:
/oraclesw9i/product/9.2/OPatch/opatch apply
3.4.10 Updating the UNIX Environment on the CTM Server Workstation
Step 1 Log in as the root user on the workstation where the CTM R6.0 server will run and insert the CTM Server Disk 1 installation CD.
Step 2 If the tnsnames.ora file in the /oraclesw9i/product/9.2/network/admin directory exists, enter the following commands to back up the file and copy it from the CTM Server Disk 1 installation CD:
cp /cdrom/cdrom0/Disk1/InstData/Solaris/VM/cfg/{small | medium | large |
highend}/tnsnames.ora /oraclesw9i/product/9.2/network/admin/tnsnames.ora
Step 3 Enter the following command to change file permissions:
chmod +w /oraclesw9i/product/9.2/network/admin/tnsnames.ora
Step 4 Edit the tnsnames.ora file by replacing the parameter CTMhostname with the hostname or IP address of the workstation where Oracle9i is installed and running.
Step 5 Edit the /var/opt/oracle/oratab file by adding the following line as the first line in the file:
<Oracle_SID>:/oraclesw9i/product/9.2:N
Note The default Oracle SID is CTM.
3.4.11 Verifying the Oracle9i Client Connection on the CTM Server Workstation
Step 1 Verify that the Oracle9i database is running on the workstation where it was installed.
Step 2 Enter the following command to log in as the oracle user:
Step 3 Enter the following command to verify that the Oracle9i database can connect to the CTM server:
Note The default Oracle SID is CTM.
You should receive the following reply:
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL= TCP)(Host=
<IP_address_where_database_is_running>)(Port= 1521)) (
CONNECT_DATA = (SID = <ORACLE_SID>)))
3.4.12 Installing the CTM R6.0 Server
To install the CTM R6.0 server, log in as the root user on the workstation where the CTM R6.0 server will run and complete the following steps:
Step 1 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 2 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 3 Insert the CTM Server Disk 1 installation CD and enter the following commands:
cdrom/cdrom0/Disk1/ctmsetup.sh
The CTM server installation begins. Wait for up to 60 seconds while the following message appears:
Ctmsetup.sh is installing CTM server...
Step 4 Click Next at the Introduction screen.
Step 5 At the License Agreement screen, read the license agreement and click the I accept the terms of the license agreement radio button. Click Next.
Step 6 At the Installation Options screen, choose Upgrade from existing CTM release; then, click Next.
Step 7 At the Database Migration Information screen, confirm the migration details and click Next.
Step 8 At the Select Products screen, check only the Install Cisco Transport Manager Server check box; then, click Next.
Step 9 At the CTM Group Information & Sudo Installation screen, confirm the name of the UNIX group to which you want to assign administrator privileges. Check or uncheck the Install CTM Sudo check box. Click Next.
Step 10 At the FTP Information screen, complete the following substeps to configure an FTP account for ONS 15216 EDFA3 software download operations:
a. Enter the following information:
•FTP username
•FTP user password
•Confirm FTP user password
•FTP directory
b. Check or uncheck the Create new FTP Account check box. If checked, the FTP user will be created automatically on the CTM server workstation by the install script. If unchecked, it is assumed that an FTP user already exists on the CTM server workstation.
c. Click Next.
Note The FTP information that you enter during the CTM server installation can be modified later from the CTM client Control Panel window. Refer to Cisco Transport Manager Release 6.0 User Guide for more information.
Step 11 At the Main Options screen, check only the Install CTM server check box; then, click Next.
Caution Be sure to uncheck the other check boxes on the Main Options screen.
Step 12 At the Server IP Address screen, specify an IP address for the CTM server; then, click Next.
Step 13 At the Select Network Configuration screen, specify the size of your network; then, click Next.
Note If you installed Oracle Standard Edition, you can only choose Small.
Step 14 At the Configure TFTP Server screen, complete the following substeps if you want to enable TFTP for the ONS 15216 EDFA2, ONS 15501, ONS 15530, and ONS 15540:
a. Check the Enable TFTP Server check box.
b. Enter the TFTP directory name. The default is /tftpboot.
c. Click Next.
Step 15 At the Specify CTM Database to Connect to screen, enter the IP address or hostname of the workstation where Oracle9i is installed; then, click Next.
Note If you entered a hostname, the setup program automatically translates the hostname to a physical IP address and prompts you to confirm the address. Click Yes.
Step 16 At the Destination Folder screen, specify where you want to install the CTM server. The default directory is /opt/CiscoTransportManagerServer. You can click Change to choose a different destination. After you specify your destination, click Next.
Note If the destination directory that you specified is a new directory, you will receive the message "Specified directory does not exist, create it?" Click Yes.
Caution CTM checks for the /opt/CiscoTransportManagerServer directory or a symbolic link to it. If CTM cannot find the /opt/CiscoTransportManagerServer directory or a symbolic link, CTM creates a symbolic link automatically. Therefore, do not delete any instances of /opt/CiscoTransportManagerServer from your CTM file structure.
Step 17 The Pre-Installation Summary screen shows the items that will be installed. Click Install.
Step 18 At the Insert New Media screen, complete the following substeps:
a. Eject the CTM Server Disk 1 installation CD, insert the CTM Server Disk 2 installation CD, and click Browse.
b. The Select a Folder dialog box opens. Double-click cdrom; then, single-click cdrom0. The filename text box now reads /cdrom/cdrom0.
c. In the Select a Folder dialog box, click Select.
d. In the Insert New Media screen, click OK.
Step 19 The Web Server Installation Summary screen summarizes the results of the web server installation. Click Next.
Step 20 The Install Complete screen summarizes the results of the installation. Click Done.
Step 21 Enter the following command to reboot the system. The CTM server starts automatically after rebooting:
Step 22 To verify that the CTM R6.0 server is running, enter the showctm command after the server reboots. The showctm command displays the CTM server version running as 6.0, followed by the build number. In the output, you will see two instances of "CTMServer," "SnmpTrapService," "SMService," and "Apache Web Server." This indicates that the CTM server is running. You should also see NE-specific processes, depending on your network. You might also see CTM GateWay/CORBA and CTM GateWay/TL1 instances.
3.4.13 Copying the Client Upgrade Files After the CTM Server Installation
You have two options for upgrading each client installation to the latest version of CTM that is on the server. You can choose to:
•Manually upgrade each client installation. If you have a previously installed version of the CTM client, you must delete the directory where the previous client is installed before installing the CTM R6.0 client. See 5.1 Installing the CTM Client and Cisco Edge Craft on Microsoft Windows, page 5-2 or 5.4 Installing the CTM Client and Cisco Edge Craft on Sun Solaris, page 5-6 for more information.
•Automatically upgrade each client when it connects to a server. During login, if the CTM client software version is older than the CTM server software version, the client will be prompted for upgrade. See 5.2 Starting the CTM Client in Microsoft Windows, page 5-5 or 5.5 Starting the CTM Client in Sun Solaris, page 5-8 for more information.
For this option you must copy the client installation files to the server. The CTM client and server installation files reside on separate installation CDs. To copy the client installation files to the server, you must eject the CTM server CD, insert the CTM client CD, and run an automated script, CopyUpgradeFiles.sh, to copy the client installation files to a specific folder under the CTM server installation directory. To do this, log in as the root user and complete the following steps.
Note The CTM server must be installed before completing the following steps.
Step 1 Enter the following commands to eject the CTM server installation CD:
Step 2 Insert the CTM client installation CD and enter the following commands:
3.5 Upgrading from Cisco MGM R5.0 to CTM R6.0 and Oracle9i on the Same Workstation
This section describes how to upgrade from Cisco MGM R5.0 to CTM R6.0 and Oracle9i when you are installing the CTM R6.0 server and the Oracle9i database on the same Sun Solaris 8 server.
Caution Before upgrading your database to CTM R6.0, it is strongly recommended that you back up your Cisco MGM R5.0 database. If you do so, you can revert to your old data in the event that the upgrade fails. To back up the database, see
Cisco Transport Manager Release 6.0 User Guide, which is available online at
http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/optnet/ctm/index.htm. Refer to the section "Backing Up the CTM Database from the CTM GUI."
Note The C shell is assumed for all UNIX commands.
When upgrading, you have two options:
•Retaining 32-Bit Oracle
•Upgrading from 32-Bit Oracle to 64-Bit Oracle
3.5.1 Retaining 32-Bit Oracle
If you are upgrading from MGM R5.0 to CTM R6.0 and you want to retain 32-bit Oracle, no action is required.
3.5.2 Upgrading from 32-Bit Oracle to 64-Bit Oracle
To upgrade from 32-bit Oracle to 64-bit Oracle, complete the procedure Upgrading from 32-Bit Oracle to 64-Bit Oracle on the CTM Database Workstation (and subsections).
3.5.3 Installing the CTM R6.0 Server and Database and Migrating Basic Data
Note Before installing the CTM database, verify that Oracle9i is installed in the /oraclesw9i directory.
To install the CTM server and database and migrate basic data, log in as the root user and complete the following steps:
Step 1 If you are using an xterm window or a remote host, enter the following command to set the DISPLAY variable:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 2 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 3 Insert the CTM Server Disk 1 installation CD and enter the following commands:
cdrom/cdrom0/Disk1/ctmsetup.sh
The setup program searches for Sun Microsystems JRE version 1.4.2_05 on your workstation.
Note If JRE is not installed, the setup program starts the Java installation program. Follow the prompts to install JRE. Enter yes at the following binary license code agreement prompt:
Do you agree to the above license terms? [yes or no]
Then, continue installing the CTM server and database.
Note If the required Solaris patches are missing, you must install them manually. Click Cancel; then, click Quit. Download the patches from SunSolve Online at http://sunsolve.sun.com. After you install the patches, continue installing the CTM server and database.
This website is Copyright © 2005, Sun Microsystems, Inc. All rights reserved.
Wait for up to 60 seconds while the following message appears:
Ctmsetup.sh is installing CTM server...
Step 4 Click Next at the Introduction screen.
Step 5 At the License Agreement screen, read the license agreement and click the I accept the terms of the license agreement radio button. Click Next.
Step 6 At the Installation Options screen, choose Upgrade from existing MGM release; then, click Next.
Step 7 At the Select Products screen, check the Install Cisco Transport Manager Server check box; then, click Next.
Note The Install Web Server check box is selected automatically when you choose Install Cisco Transport Manager Server. The Install Web Server option allows you to use an HTTP connection to download files from the CTM server to the CTM client. The web server is also used to launch the online help and CiscoView, which is an application used by CTM to configure and monitor ONS 155xx NEs. The web server is required for the CTM server.
Caution Do not check the other check boxes on the Select Products screen.
Note When you choose Install Cisco Transport Manager Server, the High Availability Installation option becomes available. This option applies only to HA installations. Do not choose it. To install HA, refer to Cisco Transport Manager High Availability Installation Guide for CTM R6.0.
Note The license for CTM GateWay/CORBA is sold separately. If you are using this feature in a production environment, you must purchase a license. You can install CTM GateWay/CORBA when you install the CTM server; however, this section assumes that you are installing the two products separately. For more information, see Chapter 4, "Installing CTM GateWay/CORBA R6.0."
Note The license for CiscoView is sold separately if used to manage the ONS 15530, ONS 15540 ESP, or ONS 15540 ESPx. If you are using this feature in a production environment to manage the ONS 15530, ONS 15540 ESP, or ONS 15540 ESPx, you must purchase a license for LAN Management Solution (LMS) Release 2.5, which includes CiscoView.
The license for CiscoView is bundled with CTM if used to manage the ONS 15501 DC or AC. You do not need to purchase a separate CiscoView license to manage the ONS 15501 DC or AC.
If you check the Install CiscoView Server check box, you receive the following prompt:
CiscoView installation has been moved to CTM Server Disk 3. After CTM server has been installed, insert the CTM Server Disk 3 and run the './installCiscoView.sh' script.
You must install the CTM server before you can install CiscoView. After installing the CTM server, see Chapter 6, "Installing and Setting Up CiscoView."
Step 8 At the CTM Group Information & Sudo Installation screen, complete the following substeps:
a. Enter the name of the UNIX group to which you want to assign administrator privileges.
b. To install sudo, check the Install CTM Sudo check box. If you do not want to install sudo, uncheck the check box.
c. Click Next.
Note For information about the sudo feature, see 1.4.1 Overview of Sudo Commands, page 1-12.
Step 9 At the FTP Information screen, complete the following substeps to configure an FTP account for ONS 15216 EDFA3 software download operations:
a. Enter the following information:
•FTP username
•FTP user password
•Confirm FTP user password
•FTP directory
b. Check or uncheck the Create new FTP Account check box. If checked, the FTP user will be created automatically on the CTM server workstation by the install script. If unchecked, it is assumed that an FTP user already exists on the CTM server workstation.
c. Click Next.
Note The FTP information that you enter during the CTM server installation can be modified later from the CTM client Control Panel window. Refer to Cisco Transport Manager Release 6.0 User Guide for more information.
Step 10 At the Main Options screen, complete the following substeps:
a. Check the Upgrade MGM database check box and specify the Oracle SID. The default is CTM.
b. Check the Install CTM server check box.
c. Click Next.
Step 11 At the Server IP Address screen, specify an IP address for the CTM server. The Hostname field is automatically populated with the hostname of the selected IP address. You can change the hostname if needed. After confirming the IP address and hostname details, click Next.
Step 12 At the Select Network Configuration screen, specify the size of your network; then, click Next.
Note If you installed Oracle Standard Edition, you can only choose Small.
Step 13 At the Configure TFTP Server screen, complete the following substeps if you want to enable TFTP for the ONS 15216 EDFA2, ONS 15501, ONS 15530, and ONS 15540:
a. Check the Enable TFTP Server check box.
b. Enter the TFTP directory name. The default is /tftpboot.
c. Click Next.
Step 14 At the Database Information screen, specify the IP address of the database workstation and specify whether or not you want to install the database in ARCHIVELOG mode. Click Next.
Step 15 At the CTM Database Installation Directories screen, the setup program verifies that the directories exist as recommended in Table 3-1. Click Next.
Step 16 The Migrate CTM Data screen appears with the following messages:
Do you want to migrate CTM data?
Do you want to migrate GateWay CORBA data?
Log into another terminal window as the root user and enter the following command to stop the server, if it is running:
Step 17 Return to the Migrate CTM Data screen and complete the following substeps:
a. Click Yes to migrate CTM data.
b. Click Yes or No to migrate CTM GateWay/CORBA data, depending on your configuration.
Note If you want to migrate CTM GateWay/CORBA data, you must click Yes at this point. You cannot migrate CTM GateWay/CORBA data later.
c. Specify the IP address or hostname of the database server that you are migrating data from.
d. Enter the password for the ctmanager oracle user. (Use the password of the database you are migrating from; the default is ctm123!.)
e. Click Next.
Note If you entered a hostname, the setup program automatically translates the hostname to a physical IP address and prompts you to confirm the address. Click Yes.
Step 18 At the Destination Folder screen, specify where you want to install the CTM server. The default directory is /opt/CiscoTransportManagerServer. You can click Change to choose a different destination. After you specify your destination, click Next.
Note If the destination directory that you specified is a new directory, you will receive the message "Specified directory does not exist, create it?" Click Yes.
Caution CTM checks for the /opt/CiscoTransportManagerServer directory or a symbolic link to it. If CTM cannot find the /opt/CiscoTransportManagerServer directory or a symbolic link, CTM creates a symbolic link automatically. Therefore, do not delete any instances of /opt/CiscoTransportManagerServer from your CTM file structure.
Step 19 The Pre-Installation Summary screen shows the items that will be installed. Click Install.
Note It might take 30 to 60 minutes or longer to migrate basic data, depending on your system performance and on the amount of data that you are migrating.
Step 20 At the Insert New Media screen, complete the following substeps:
a. Eject the CTM Server Disk 1 installation CD, insert the CTM Server Disk 2 installation CD, and click Browse.
b. The Select a Folder dialog box opens. Double-click cdrom; then, single-click cdrom0. The filename text box now reads /cdrom/cdrom0.
c. In the Select a Folder dialog box, click Select.
d. In the Insert New Media screen, click OK.
Step 21 The Web Server Installation Summary screen summarizes the results of the web server installation. Click Next.
Step 22 The Install Complete screen summarizes the results of the installation. Click Done.
Step 23 Enter the following command to reboot the system. The CTM server starts automatically after rebooting:
Step 24 To verify that the CTM R6.0 server is running, enter the showctm command after the server reboots. The showctm command displays the CTM server version running as 6.0, followed by the build number. In the output, you will see two instances of "CTMServer," "SnmpTrapService," "SMService," and "Apache Web Server." This indicates that the CTM server is running. You should also see MGX NE and PM services. You might also see CTM GateWay/CORBA and CTM GateWay/TL1 instances.
3.5.4 Copying the Client Upgrade Files After the CTM Server Installation
You have two options for upgrading each client installation to the latest version of CTM that is on the server. You can choose to:
•Manually upgrade each client installation. If you have a previously installed version of the CTM client, you must delete the directory where the previous client is installed before installing the CTM R6.0 client. See 5.1 Installing the CTM Client and Cisco Edge Craft on Microsoft Windows, page 5-2 or 5.4 Installing the CTM Client and Cisco Edge Craft on Sun Solaris, page 5-6 for more information.
•Automatically upgrade each client when it connects to a server. During login, if the CTM client software version is older than the CTM server software version, the client will be prompted for upgrade. See 5.2 Starting the CTM Client in Microsoft Windows, page 5-5 or 5.5 Starting the CTM Client in Sun Solaris, page 5-8 for more information.
For this option you must copy the client installation files to the server. The CTM client and server installation files reside on separate installation CDs. To copy the client installation files to the server, you must eject the CTM server CD, insert the CTM client CD, and run an automated script, CopyUpgradeFiles.sh, to copy the client installation files to a specific folder under the CTM server installation directory. To do this, log in as the root user and complete the following steps.
Note The CTM server must be installed before completing the following steps.
Step 1 Enter the following commands to eject the CTM server installation CD:
Step 2 Insert the CTM client installation CD and enter the following commands:
3.6 Upgrading from Cisco MGM R5.0 to CTM R6.0 and Oracle9i on Separate Workstations
This section describes how to upgrade from Cisco MGM R5.0 to CTM R6.0 and Oracle9i when you are installing the CTM R6.0 server and the Oracle9i database on separate Sun Solaris 8 servers.
Caution Before upgrading your database to CTM R6.0, it is strongly recommended that you back up your Cisco MGM R5.0 database. If you do so, you can revert to your old data in the event that the upgrade fails. To back up the database, see
Cisco Transport Manager Release 6.0 User Guide, which is available online at
http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/optnet/ctm/index.htm. Refer to the section "Backing Up the CTM Database from the CTM GUI."
Note The C shell is assumed for all UNIX commands.
When upgrading, you have two options:
•Retaining 32-Bit Oracle
•Upgrading from 32-Bit Oracle to 64-Bit Oracle on the CTM Database Workstation
3.6.1 Retaining 32-Bit Oracle
3.6.1.1 Retaining 32-Bit Oracle on the CTM Database Workstation
If you are upgrading from MGM R5.0 to CTM R6.0 and you want to retain 32-bit Oracle, no action is required.
3.6.1.2 Retaining 32-Bit Oracle on the CTM Server Workstation
If you are upgrading from MGM R5.0 to CTM R6.0 and you want to retain 32-bit Oracle, enter the following command to verify that the Oracle9i database can connect to the CTM server:
Note The default Oracle SID is MGM5_0.
You should receive the following reply:
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL= TCP)(Host=
<IP_address_where_database_is_running>)(Port= 1521)) (
CONNECT_DATA = (SID = <ORACLE_SID>)))
3.6.2 Upgrading from 32-Bit Oracle to 64-Bit Oracle on the CTM Database Workstation
Complete the following subsections to upgrade from 32-bit Oracle to 64-bit Oracle on the CTM database workstation.
3.6.2.1 Shutting Down the MGM R5.0 Database Instance on the CTM Database Workstation
Step 1 Complete the following substeps to shut down all of the MGM clients:
a. In the Domain Explorer window, choose Administration > MGM Users.
b. In the MGM Users table, choose Administration > Logged In MGM Users.
c. In the Logged In MGM Users table, select the user whose session will be ended and choose Administration > Log Out User (or click the Log Out User tool).
d. Click Yes at the following prompt:
This operation will log out the selected CTM user. The process will take approximately
1 minute and this CTM client will be unusable until then. Do you wish to continue?
Wait while the MGM server logs out the selected MGM client. The MGM GUI is frozen for approximately 1 minute until the request is complete.
Step 2 As the root user, enter the following command to stop the workstation where the MGM server is running:
Step 3 On the workstation where the MGM database is running, enter the following commands to stop the Oracle listener and shut down all Oracle processes, if they are running:
setenv ORACLE_HOME /oraclesw9i/product/9.2
3.6.2.2 Setting the Environment for Installation on the CTM Database Workstation
Log in as the root user on the workstation where the CTM server will run and complete the following steps:
Step 1 Enter the following command to verify that the disk directories shown in Table 3-3 exist:
Table 3-4 Disk Directories
Directory
|
Contents
|
/ctm_backup1
|
For the backed-up configuration files
|
/oraclesw9i
|
For the Oracle software
|
/tftpboot
|
For the TFTP directory
Note Disk partitioning is not required for /tftpboot, but the directory is required.
|
Step 2 Enter the following command to verify the password file:
Step 3 Navigate to the entry that looks similar to the following, and verify that the entry exists:
oracle:x:100:3303::/oraclesw9i:/bin/csh
Step 4 Enter the following command to quit:
3.6.2.3 Downloading the Oracle Patch Installer on the CTM Database Workstation
Note The Oracle patch installer is used to install additional Oracle patches. If you already installed the Oracle patch installer, you can skip this section.
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 2617419.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download.
Step 8 In the list of patches returned, click the first patch, which has the latest release number.
Note Do not be concerned if the patch refers to a later version of Oracle.
Step 9 In the Patch 2617419 window, go to the Platform or Language field and choose Generic Platform (the default).
Step 10 Click Download.
Step 11 Save the patch to the /oraclesw9i/product/9.2 directory.
Step 12 Enter the following commands to change the patch ownership and unzip the patch:
chown oracle:dba /oraclesw9i/product/9.2/p2617419_10102_GENERIC.zip
cd /oraclesw9i/product/9.2
unzip p2617419_10102_GENERIC.zip
3.6.2.4 Downloading the 64-Bit 9.2.0.6 Patch for Oracle9i on the CTM Database Workstation
Step 1 Go to http://metalink.oracle.com and click Login to MetaLink. Enter your Oracle MetaLink username and password.
Note This website is Copyright © 2004, Oracle Corporation. All rights reserved.
Step 2 Click Patches.
Step 3 Click Simple Search.
Step 4 In the Search by Patch Number(s) field, enter 3948480.
Step 5 In the Platform or Language field, choose one of the following options, depending on your Oracle version:
•Solaris Operating System (SPARC 32-bit)
•Solaris Operating System (SPARC 64-bit)
Step 6 Click Go.
Step 7 Click Download. For 64-bit Oracle, download p3948480_9206_SOLARIS64.zip.
Step 8 As the oracle user, save the patch to the /oraclesw9i directory and enter the following commands to unzip the .zip file:
unzip <patch_zip_filename>
Step 9 Enter the following commands to prepare the patch set:
unzip p3948480_9206_SOLARIS64.zip
3.6.2.5 Uninstalling 32-Bit Oracle9i on the CTM Database Workstation
You must download the 9.2.0.6 patch before uninstalling 32-bit Oracle9i because you need Oracle Universal Installer version 10.1.0.3 to uninstall Oracle9i.
Step 1 Enter the following command to enable the xterm connection from the clients:
Step 2 Enter the following command to set the display on your terminal:
setenv DISPLAY <hostname_or_IP_address>:0.0
Step 3 Enter the following command to verify that the display is set correctly:
In the output, you should see:
<hostname_or_IP_address>:0.0
Step 4 Enter the following commands to launch Oracle Universal Installer version 10.1.0.3, which will allow you to uninstall the previous version of Oracle:
Step 5 At the Welcome screen, click Deinstall Products.
Step 6 In the Inventory dialog box, complete the following substeps:
a. Expand Independent Products and select all of the components under Independent Products.
b. Select OHOME1.
c. Click Remove.
Step 7 The Confirmation dialog box shows which products will be uninstalled. Click Yes.
Step 8 The Remove progress bar tracks the progress of the uninstallation. When the Remove progress bar disappears, the uninstallation is complete. Click Close in the Inventory dialog box.
Step 9 Return to the Oracle Universal Installer Welcome screen an
