Table B-1 CTM Config Table Parameters
Section Name
|
Parameter Name
|
Definition
|
transportManager
|
jmoco-port
|
Port where JMOCO events are sent.
|
main-error-level
|
Error levels supported in CTM. Values are: trace, debug, minor, major, critical.
|
min-alarm-update-interval
|
Minimum time in seconds when an active_alarm_update event is sent.
|
ems-sys-id
|
System ID indicating who sent the event (for example, if the event is generated by the EMS, the system ID would be CTM.)
|
preferred-jar-path
|
Path to get CTC jar files.
|
preferred-jar-version
|
Version of the CTC jar that needs to be picked.
|
tl1-connection-timeout
|
Timeout period if a TL1 connection has not been used.
|
jmoco-trace-frequency
|
(Not used)
|
jmoco-max-user-sessions
|
Maximum number of sessions a jmoco engine can support.
|
oss-thread-count
|
Maximum number of threads that can be spawned in CTM.
|
oss-work-queue-threshold
|
Maximum number of work objects that can be added into the work queue.
|
oss-max-threads
|
Maximum number of threads that can be read from the work queue.
|
oss-jmoco-threads
|
Number of threads used to read events from the work queue.
|
oss-jmoco-event-threads
|
Number of threads used to distribute events from the work queue to registered users.
|
oss-socket-send-size
|
Maximum size of the buffer that the socket can support to send.
|
oss-socket-recv-size
|
Maximum size of the buffer that the socket can support to receive.
|
database
|
db-connection-pool-size
|
Number of connections in JDBC connection pool (default is 10).
|
db-archivelog-enabled
|
DB archived log mode option enabled or not (default is false [not enabled]).
|
db-backup-state
|
State of the database hot backup (default is 0).
|
db-max-sessions
|
Maximum number of sessions that can be opened with the database.
|
db-no-pruning-threads
|
Number of threads that configure to run db prune (default is 1).
|
gatewayTL1
|
gwTL1ForwardingAgent
|
Indicates if Gateway/TL1 is installed, stopped, or started.
|
response-parameters
|
(Not used)
|
ne-name
|
alarm-logic
|
in-progress-frequency
|
oss-mux
|
oss-pt
|
load-db-nes
|
deny-act-user
|
oss-port
|
Gateway\TL1 port.
|
15454-vasco-tl1-port
|
Vasco TL1 port for 15454.
|
15454-tl1-port
|
TL1 port.
|
15327-tl1-port
|
15800-tl1-port
|
15801-tl1-port
|
15808-tl1-port
|
15216-oadm2-tl1-port
|
15216-edfa-tl1-port
|
15600-tl1-port
|
15600-tl1-telnet-port
|
(Not used)
|
15501-tl1-port
|
TL1 port.
|
15530-tl1-port
|
15540-esp-tl1-port
|
15540-espx-tl1-port
|
gatewayTL1 (continued)
|
poll-frequency
|
Time in seconds GateWay/TL1 checks the status of the NE.
|
error-level
|
Indicates debug level for the Gateway/TL1 service module.
|
gwTL1Timeout
|
Time in seconds before GatewayTL1 times out.
|
gwTL1LoginTimeout
|
Enables or disables GwTL1TimeOut period if the ACT-USER is not performed before the timeout period.
|
gwTL1CmdTimeout
|
Enables or disables GwTL1TimeOut period if any valid TL1 command is not performed before the timeout period.
|
gwTL1Connections
|
Number of TL1 connections to Gateway/TL1.
|
enable-gwtl1-advisory
|
Enables or disables display of advisory messages.
|
gwtl1-advisory-message
|
Gateway/TL1 advisory message.
|
gatewaySNMP
|
gatewaySNMP
|
Indicates if Gateway/SNMP is installed, stopped, or started.
|
snmp-hosts
|
SNMP trap destination hosts.
|
gatewayCORBA
|
gatewayCORBA
|
Indicates if CORBA Gateway is installed, stopped, or started.
|
corba-request-timeout
|
CORBA timeout value.
|
thread-pool-size
|
Thread pool size used in CORBA Gateway.
|
iiop-listen-port
|
CORBA Gateway listening port.
|
error-level
|
Debug level for the CORBA Gateway module.
|
heartbeat-interval
|
Interval minutes for the heartbeat event.
|
enable-gwcorba-encryption
|
Indicates if CORBAGateway encryption feature is on.
|
ne
|
poll-frequency
|
Wait duration for next health poll to start.
|
corba-request-timeout
|
CORBA timeout value.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for NE service process.
|
ne-thread-pool-size
|
Number of threads available for NE discovery.
|
ne-discov-thread-pool-size
|
Number of threads for initial poll, alarm resync and config resync.
|
snmp-trap-thread-pool-size
|
Number of threads for SNMP trap event converter.
|
alarm-thread-pool-size
|
Number of threads for alarm dispatcher.
|
pm
|
number-of-collectors
|
Property to configure the number of threads for the Collector Thread Pool. This thread pool is used to poll the NEs and get performance statistics.
|
number-of-writers
|
Property to configure the number of threads for the Database Writer Thread Pool. This thread pool is used to write performance statistics in the database.
|
number-of-nes
|
(Not used)
|
store-non-zeros-only
|
Runs the PM in optimized mode. If the performance counts are zero, then this parameter controls on whether it should be written to the database or not.
|
pm-disk-limit
|
(Not used)
|
pm-jvm-heap-init
|
Initial heap size for PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for PM service process.
|
pm-15-min-retrieval-enabled
|
Controls PM alarm generation. When enabled and PM collection fails for a 15 minute bucket, a PM alarm is emitted.
|
pm-15-min-retrieval-secs-between-
retries
|
Specifies seconds to wait before CTM retries and polls the NE. Used when PM Collection fails in normal mode for 15 minute bucket.
|
pm-15-min-retrieval-number-of-retries
|
Specifies number of times CTM should retry and poll the NEs. Used when PM Collection fails in normal mode for 15 minute bucket.
|
pm-1-day-retrieval-enabled
|
Controls PM alarm generation. When enabled and PM collection fails for a one day bucket, a PM alarm is emitted.
|
pm-1-day-retrieval-secs-between-
retries
|
Specifies number of times CTM should retry and poll the NEs. Used when PM collection fails in normal mode for one day bucket.
|
pm-1-day-retrieval-number-of-retries
|
Specifies number of times CTM should retry and poll the NEs. Used when PM collection fails in normal mode for 1 day bucket.
|
cm
|
config-vlan-thread-count
|
Number of threads for doing vlan discovery.
|
config-vlan-autosync-delay
|
Delay after which time the topologies and vlans are synched with the NE.
|
config-dsp-max-idle-time
|
Set to check if sufficient time has passed from the last event received and all topology audits have been completed.
|
config-dsp-msync-wait-time
|
Time to wait until the set time for Node Manager Sync to be completed.
|
config-max-partial-topo-time
|
Time to schedule a task to scan and mark all partial topologies as incomplete.
|
config-sync-thread-run-delay
|
Frequency of task which checks if the data service module is ready for provisioning (data provisioning ready state).
|
config-topo-incomplete-thread-run-
delay
|
Time to schedule a task to declare the incomplete topologies.
|
dsp-debug-telnet-port
|
Telnet port to turn on the DataService.log for debugging topology discovery-related information.
|
config-resync-thread-pool-size
|
(Not used)
|
config-poll-frequency
|
Polling period to check if the config resync time has been reached.
|
config-resync-frequency
|
Periodic frequency at which config resync is performed.
|
config-request-queue-size
|
(Not used)
|
iiop-listen-port
|
(Not used)
|
backup-frequency
|
Frequency at which backup should be performed (for example, daily, weekly, or just once).
|
cm (continued)
|
backup-copies-ons15454
|
Number of copies of backed up configuration and provisioning information residing in the Flash memory of the NEs
|
backup-copies-ons15800
|
backup-copies-ons15327
|
backup-copies-ons15540
|
backup-copies-ons15454sdh
|
backup-copies-ons15600
|
backup-copies-ons15530
|
backup-copies-ons15540xps
|
backup-copies-ons15216edfa
|
backup-status-ons15454
|
Current status of the task: Queued, Running, Canceled, Failed, Succeeded, or Waiting.
|
backup-status-ons15800
|
backup-status-ons15327
|
backup-status-ons15540
|
backup-status-ons15540xps
|
backup-status-ons15530
|
backup-status-ons15454sdh
|
backup-status-ons15600
|
backup-status-ons15216edfa
|
backup-time-ons15454
|
Time for the NE configuration backup.
|
backup-time-ons15800
|
backup-time-ons15327
|
backup-time-ons15540
|
backup-time-ons15454sdh
|
backup-time-ons15600
|
backup-time-ons15530
|
backup-time-ons15540xps
|
backup-time-ons15216edfa
|
cm (continued)
|
manual_backup-copies-ons15454
|
Number of copies that can be manually backed up. Each NE backup is performed by selecting the "User Specified" radio active button found in Configuration>Memory Backup>User Specified.
|
manual_backup-copies-ons15800
|
manual_backup-copies-ons15327
|
manual_backup-copies-ons15540
|
manual_backup-copies-ons15454sdh
|
manual_backup-copies-ons15600
|
manual_backup-copies-ons15530
|
manual_backup-copies-ons15540xps
|
manual_backup-copies-ons15216edfa
|
manual_backup-copies
|
alarm-data
|
Parameters used for Cerent auto backup.
|
pm-data
|
auditlog-data
|
auto-job-thread-pool-size
|
Number of threads used to read the auto jobs from the work queue.
|
manual-job-thread-pool-size
|
Number of threads used to read the manual jobs from the work queue.
|
snmp
|
snmpTrapService
|
Enables or disables SNMP trap service on CTM server startup. Default is enabled.
|
snmp-trap-queue-size
|
Maximum number of traps that can be queued in SNMP trap service before distributed to NE services. When the queue reaches MAX, incoming traps are dropped. Default:10000.
|
snmp-trap-drop-size
|
Threshold to drop incoming traps. Default:100.
|
snmp-trap-forwarding-port
|
Snmp Gateway trap port. Default:8765.
|
snmp-trap-port
|
Incoming trap port. Default:162.
|
snmp-mibs-dir
|
MIB File directory. Default:/mibs.
|
st-error-level
|
Debug log level. Default:minor.
|
serviceManager
|
sm-jvm-heap-init
|
Initial heap size allocated to the SM service.
|
sm-jvm-heap-max
|
Maximum heap size allocated to the SM service.
|
sm-error-level
|
Error level for the process. Values are: debug, trace, minor, major, or critical.
|
service-stop-timer
|
Time interval for which the SM Service waits for the service to stop.
|
hello-poll-interval
|
Poll interval at which hello operation is performed on an NE.
|
hello-stop-timer
|
Time interval for which the SM Service waits for the service to gracefully shutdown.
|
hello-kill-timer
|
Time interval after which the SM Service forcibly kills the service as it is not responding.
|
diskspace-poll-period
|
(Not used)
|
ons15200-ne
|
ne-service
|
The NE service process automatically starts whenever at least one NE is added to the CTM domain. If no NEs are present, this service will not be running. If previously running, this service will terminate at soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. From the client machine, this value can be changed through Administration>Control Panel>NE Service>(<NE name>)>Error Level.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration>Control Panel>NE Service>(<NE service name>)> Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for NE service process.
|
ons15216-ne
|
ne-service
|
The NE service process automatically starts whenever at least one NE is added to the CTM domain. If no NEs are present, this service will not be running. If previously running, this service will terminate at soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. From the client machine, this value can be changed through Administration>Control Panel>NE Service>(<NE name>)>Error Level.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration>Control Panel>NE Service>(<NE service name>)> Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for NE service process.
|
ons15327-ne
|
fault-sync
|
Enables or disables historical alarm collection.
|
ons15600-ne
|
fault-sync
|
Enables or disables historical alarm collection.
|
ons15454-ne
|
ne-service
|
The NE service process automatically starts whenever at least one NE is added to the CTM domain. If no NEs are present, this service will not be running. If previously running, this service will terminate at soon as no NEs are in the domain.
|
ne-low-threshold
|
Threshold value for the maximum number of NEs that can be discovered.
|
ne-threshold
|
Maximum number of NEs that can be handled.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. From the client machine, this value can be changed through Administration>Control Panel>NE Service>(<NE name>)>Error Level.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration>Control Panel>NE Service>(<NE service name>)> Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads available for NE discovery.
|
ne-ios-cr-thread-pool-size
|
Number of threads in a pool where each thread used to process IOS config resync updates. Default:10.
|
ne-ios-updates-cr-frequency
|
Number of seconds when IOS config resync updates are processed. Default:60.
|
ons15454-ne (continued)
|
audit-trail-collection-interval
|
Wait duration for next audit trail collection to start.
|
audit-trail-thread-count
|
Number of threads that can be used to collect audit trail.
|
fault-sync
|
Enables or disables historical alarms collection.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for NE service process.
|
blsr-interval
|
Difference in interval between EAST and WEST port job execution.
|
client-list-thread-pool-size
|
Number of threads in a pool where each thread used to poll the ENE client list from the Gateway NE (i.e. GNE with proxy turned on). Default:20.
|
ctm-event-disp-thread-count
|
Number of threads for dispatching events.
|
ctm-invupd-thread-count
|
Number of threads to handle inventory updates.
|
ons15454sdh-ne
|
ne-service
|
The NE service process automatically starts whenever at least one NE is added to the CTM domain. If no NEs are present, this service will not be running. If previously running, this service will terminate at soon as no NEs are in the domain.
|
ne-low-threshold
|
Threshold value for the maximum number of NEs that can be discovered.
|
ne-threshold
|
Maximum number of NEs that can be handled.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration>Control Panel>NE Service>(<NE service name>)> Config Resync Interval.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. From the client machine, this value can be changed through Administration>Control Panel>NE Service>(<NE name>)>Error Level.
|
ne-thread-pool-size
|
Number of threads available for NE discovery.
|
ne-ios-cr-thread-pool-size
|
Number of threads in a pool where each thread used to process IOS config resync updates. Default:10.
|
ne-ios-updates-cr-frequency
|
Number of seconds when IOS config resync updates are processed. Default:60.
|
audit-trail-collection-interval
|
Wait duration for next audit trail collection to start.
|
audit-trail-thread-count
|
Number of threads that can be used to collect audit trail.
|
ons15454sdh-ne (continued)
|
fault-sync
|
Enables or disables historical alarms collection.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for NE service process.
|
mspring-interval
|
Difference in interval between EAST and WEST port job execution.
|
ons155xx-ne
|
ne-service
|
The NE service process automatically starts whenever at least one NE is added to the CTM domain. If no NEs are present, this service will not be running. If previously running, this service will terminate at soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. From the client machine, this value can be changed through Administration>Control Panel>NE Service>(<NE name>)>Error Level.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration>Control Panel>NE Service>(<NE service name>)> Config Resync Interval.
|
discovery-threads-pool-size
|
Number of discovery threads available for discovering ONS 155xx NEs.
|
discovery-threads-p1
|
Number of threads used by ONS 155xx NE service for 155xx device discovery, including inventory and alarms.
|
discovery-threads-p2
|
Number of threads used by ONS155xx NE service for toplogy and circuit discovery.
|
discovery-wait-on-ne-create
|
Wait time in seconds after an ONS155xx NE has been added to the network.
|
discovery-enable-cdp
|
Enables or disables discovery of configured cdp neighbors.
|
discovery-auto-neighbor
|
Enables or disables discovery of configured non-cdp neighbors.
|
discovery-auto-delete-stale-links
|
Enables or disables AutoDeletion of stale links from database.
|
ons155xx-ne (continued)
|
tftp-timeout
|
Time out period for any tftp operations to and from ONS 155xx and the server.
|
backup-config-before-restore
|
Enables or disables backup of NE config before restoring new config.
|
snmp-pdu-maxvars
|
Size of SNMP pdu varbinds used while creating a connection with the NE.
|
EntityAlarmsToIgnore
|
Indicates if any 155xx entity alarms to be ignored exist.
|
ne-thread-pool-size
|
Number of threads available for NE discovery.
|
discovery-fast-mode
|
Enables or disables discovery of ONS 155xx NEs in fast mode.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for NE service process.
|
ons15800-ne
|
ne-service
|
The NE service process automatically starts whenever at least one NE is added to the CTM domain. If no NEs are present, this service will not be running. If previously running, this service will terminate at soon as no NEs are in the domain.
|
| |
ne-threshold
|
Maximum number of NEs that can be handled.
|
| |
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. From the client machine, this value can be changed through Administration>Control Panel>NE Service>(<NE name>)>Error Level.
|
| |
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration>Control Panel>NE Service>(<NE service name>)> Config Resync Interval.
|
ons15800-ne (continued)
|
ne-thread-pool-size
|
Number of threads available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for NE service process.
|
ons15801-ne
|
ne-service
|
The NE service process automatically starts whenever at least one NE is added to the CTM domain. If no NEs are present, this service will not be running. If previously running, this service will terminate at soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. From the client machine, this value can be changed through Administration>Control Panel>NE Service>(<NE name>)>Error Level.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration>Control Panel>NE Service>(<NE service name>)> Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ons15808-ne
|
ne-service
|
The NE service process automatically starts whenever at least one NE is added to the CTM domain. If no NEs are present, this service will not be running. If previously running, this service will terminate at soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. From the client machine, this value can be changed through Administration>Control Panel>NE Service>(<NE name>)>Error Level.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration>Control Panel>NE Service>(<NE service name>)> Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for NE service process.
|
ons15302-ne
|
ne-service
|
The NE service process automatically starts whenever at least one NE is added to the CTM domain. If no NEs are present, this service will not be running. If previously running, this service will terminate at soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. From the client machine, this value can be changed through Administration>Control Panel>NE Service>(<NE name>)>Error Level.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration>Control Panel>NE Service>(<NE service name>)> Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for NE service process.
|
ne-sntp-default-sync-time
|
Default value used for the resync time.
|
ons15305-ne
|
ne-service
|
The NE service process automatically starts whenever at least one NE is added to the CTM domain. If no NEs are present, this service will not be running. If previously running, this service will terminate at soon as no NEs are in the domain.
|
ne-threshold
|
Maximum number of NEs that can be handled.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. From the client machine, this value can be changed through Administration>Control Panel>NE Service>(<NE name>)>Error Level.
|
ne-resync-frequency
|
Periodic frequency at which configuration resynchronization is performed. This value can be modified from the CTM client through Administration>Control Panel>NE Service>(<NE service name>)> Config Resync Interval.
|
ne-thread-pool-size
|
Number of threads available for NE discovery.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for NE service process.
|
ne-sntp-default-sync-time
|
Default value used for the resync time.
|
unmanaged-ne
|
ne-service
|
The NE service process automatically starts whenever at least one NE is added to the CTM domain. If no NEs are present, this service will not be running. If previously running, this service will terminate at soon as no NEs are in the domain.
|
ne-error-level
|
NE service error log level. By default, minor severity log messages are entered in the NE service logs. From the client machine, this value can be changed through Administration>Control Panel>NE Service>(<NE name>)>Error Level.
|
ne-threshold
|
Maximum number of NEs that can be handled.
|
ne-jvm-heap-init
|
Initial heap size for NE service process.
|
ne-jvm-heap-max
|
Maximum heap size for NE service process.
|
ons15454-pm
|
pm-service
|
Possible values are active or not-active. Default value is not-active. If value of the property is active, corresponding PM service will be started when the PM is enabled on NE(s). Value of this property should be set to active to collect PM counts on NEs. Value of this property can be changed from selecting the following: Administration>ControlPanel>PM Service>(Select Type of NEs).
|
pm-threshold
|
Maximum number of NEs managed by the PM service process.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. From the client machine, this value can be changed through Administration>Control Panel>PM Service>(<NE name>)>Error Level.
|
pm-http-retries
|
(Not used)
|
pm-wait-period
|
pm-interface-ds1
|
Enables or disables performance statistics collection.
|
pm-interface-ds3
|
pm-interface-sonet
|
pm-interface-sts
|
pm-interface-vt
|
pm-interface-enet
|
Enables or disables Ethernet performance counts collection.
|
pm-interface-physical
|
Enables or disables the physical performance statistics collection for optical cards.
|
pm-interface-dwdm
|
Enables or disables OTN Section, Line, and Path performance statistics collection for DWDM cards.
|
pm-snmp
|
Enables or disables SNMP performance monitoring for Daytona cards on 15454.
|
pm-jvm-heap-init
|
Initial heap size for PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for PM service process.
|
ons15454sdh-pm
|
pm-service
|
Possible values are active or not-active. Default value is not-active. If value of the property is active, corresponding PM service will be started when the PM is enabled on NE(s). Value of this property should be set to active to collect PM counts on NEs. Value of this property can be changed from selecting the following: Administration>ControlPanel>PM Service>(Select Type of NEs).
|
pm-threshold
|
Maximum number of NEs managed by the PM service process.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. From the client machine, this value can be changed through Administration>Control Panel>PM Service>(<NE name>)>Error Level.
|
pm-http-retries
|
(Not used)
|
pm-wait-period
|
pm-interface-E1
|
Enables or disables performance statistics collection.
|
pm-interface-E3
|
pm-interface-E4
|
pm-interface-ds3I
|
pm-interface-sdh
|
pm-interface-HO
|
pm-interface-LO
|
pm-interface-enet
|
Enables or disables Ethernet performance counts collection.
|
pm-interface-physical
|
Enables or disables physical performance statistics collection for optical cards.
|
pm-interface-dwdm-sdh
|
Enables or disables OTN Section, Line, Path performance statistics collection for DWDM cards.
|
pm-snmp
|
Enables or disables SNMP performance monitoring for Daytona cards on 15454 sdh.
|
pm-jvm-heap-init
|
Initial heap size for PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for PM service process.
|
ons15600-pm
|
pm-service
|
Possible values are active or not-active. Default value is not-active. If value of the property is active, corresponding PM service will be started when the PM is enabled on NE(s). Value of this property should be set to active to collect PM counts on NEs. Value of this property can be changed from selecting the following: Administration>ControlPanel>PM Service>(Select Type of NEs).
|
pm-threshold
|
Maximum number of NEs managed by the PM service process.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. From the client machine, this value can be changed through Administration>Control Panel>PM Service>(<NE name>)>Error Level.
|
pm-http-retries
|
(Not used)
|
pm-wait-period
|
(Not used)
|
pm-interface-sonet
|
Enables or disables SONET Section and Line performance statistics collection.
|
pm-interface-sts
|
Enables or disables SONET Sts Path performance statistics collection.
|
pm-jvm-heap-init
|
Initial heap size for PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for PM service process.
|
ons155xx-pm
|
pm-service
|
Possible values are active or not-active. Default value is not-active. If value of the property is active, corresponding PM service will be started when the PM is enabled on NE(s). Value of this property should be set to active to collect PM counts on NEs. Value of this property can be changed from selecting the following: Administration>ControlPanel>PM Service>(Select Type of NEs).
|
pm-threshold
|
Maximum number of NEs managed by the PM service process.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. From the client machine, this value can be changed through Administration>Control Panel>PM Service>(<NE name>)>Error Level.
|
pm-jvm-heap-init
|
Initial heap size for PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for PM service process.
|
pm-poll-delay
|
Indicates the delay time in seconds for 15 minute and 24 hour PM collections to start.
|
ons158xx-pm
|
pm-service
|
Possible values are active or not-active. Default value is not-active. If value of the property is active, corresponding PM service will be started when the PM is enabled on NE(s). Value of this property should be set to active to collect PM counts on NEs. Value of this property can be changed from selecting the following: Administration>ControlPanel>PM Service>(Select Type of NEs).
|
pm-threshold
|
Maximum number of NEs managed by the PM service process.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. From the client machine, this value can be changed through Administration>Control Panel>PM Service>(<NE name>)>Error Level.
|
pm-jvm-heap-init
|
Initial heap size for PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for PM service process.
|
pm-15m-delay
|
Time (in seconds) to wait after the quarter exceeds before collecting PMs.
|
pm-24h-delay
|
Time (in seconds) to wait after the 24 hours exceed before collecting PMs.
|
ons15216-pm
|
pm-service
|
Possible values are active or not-active. Default value is not-active. If value of the property is active, corresponding PM service will be started when the PM is enabled on NE(s). Value of this property should be set to active to collect PM counts on NEs. Value of this property can be changed from selecting the following: Administration>ControlPanel>PM Service>(Select Type of NEs).
|
pm-threshold
|
Maximum number of NEs managed by the PM service process.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. From the client machine, this value can be changed through Administration>Control Panel>PM Service>(<NE name>)>Error Level.
|
pm-jvm-heap-init
|
Initial heap size for PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for PM service process.
|
ons1530x-pm
|
pm-service
|
Possible values are active or not-active. Default value is not-active. If value of the property is active, corresponding PM service will be started when the PM is enabled on NE(s). Value of this property should be set to active to collect PM counts on NEs. Value of this property can be changed from selecting the following: Administration>ControlPanel>PM Service>(Select Type of NEs).
|
pm-threshold
|
Maximum number of NEs managed by the PM service process.
|
pm-error-level
|
PM service error log level. By default, minor severity log messages are entered in the PM service logs. From the client machine, this value can be changed through Administration>Control Panel>PM Service>(<NE name>)>Error Level.
|
pm-jvm-heap-init
|
Initial heap size for PM service process.
|
pm-jvm-heap-max
|
Maximum heap size for PM service process.
|
pm-15m-delay
|
Time (in seconds) to wait after the quarter exceeds before collecting PMs.
|
pm-24h-delay
|
Time (in seconds) to wait after the 24 hours exceed before collecting PMs.
|
security
|
password-age
|
Set the password aging interval to any interval between 0 and 999 days. You are prompted to change the password after the specified number of days. The default is 30 days.
|
max-unsuccessful-attempts
|
Set the maximum number of attempts a user is allowed to log in before being locked out for the length of time specified in the Lockout Time field. The allowable range is 0 to 10 retries; the default is 5 retries.
|
lockout-period
|
Set the number of minutes a user's CTM session is inactive before CTM automatically locks the user out. The allowable range is 0 to 120 minutes in 1 minute increments; the default is 30 minutes. A value of 0 disables this feature.
|
security (continued)
|
client-lockout
|
Enables or disables client lockout.
|
client-lockout-period
|
Set the number of minutes a user's CTM session is inactive before CTM automatically logs the user out. The allowable range is 0 to 1440 minutes in 1 minute increments. A value of 0 disables this feature.
|
client-logout
|
Enables or disables client logout.
|
client-logout-period
|
Set the number of minutes a user's CTM session is inactive before CTM automatically logs the user out. The allowable range is 0 to 1440 minutes in 1 minute increments. A value of 0 disables this feature.
|
security-advisory-message
|
(This parameter is not applicable to ONS 155xx NEs.) If checked, the advisory message that appears on login is enabled.
|
security (continued)
|
ons158xxusername
|
Usernames and passwords used to connect to a specific NE.
|
ons158xxpassword
|
ons158xxGWTL1username
|
ons158xxGWTL1password
|
ons1530xusername
|
ons1530xpassword
|
ons1530xGWTL1username
|
ons1530xGWTL1password
|
ons15454username
|
ons15454password
|
ons15454GWTL1username
|
ons15454GWTL1password
|
ons15454MLSeriesusername
|
ons15454MLSeriespassword
|
ons15327username
|
ons15327password
|
ons15327GWTL1username
|
ons15327GWTL1password
|
ons15454SDHusername
|
ons15454SDHpassword
|
ons15454SDHGWTL1username
|
ons15454SDHGWTL1password
|
ons15454SDHMLSeriesusername
|
ons15454SDHMLSeriespassword
|
ons15216OADMUserName
|
ons15216OADMUserPass
|
ons15216OADMGWTL1UserName
|
ons15216OADMGWTL1UserPass
|
ons15216EDFAGWTL1UserName
|
ons15216EDFAGWTL1UserPass
|
ons155xxusername
|
(N/A)
|
ons155xxpassword
|
(N/A)
|
ons155xxGWTL1username
|
Username and password used to connect to the ons155xxGWTL1 NE.
|
ons155xxGWTL1password
|
telnet-password
|
Telnet password.
|
ne-global-user-name
|
NE global username.
|
security (continued)
|
ne-global-user-password
|
NE global password.
|
ons15600username
|
Usernames and passwords used to connect to a specific NE.
|
ons15600password
|
ons15600GWTL1username
|
ons15600GWTL1password
|
ui
|
unack-alarm
|
Enables or disables the ability to unacknowledge alarms that have been acknowledged.
|
subnetwork-auto-grouping
|
Enables or disables the ability to automatically group NEs in subnetworks.
|
overwrite-alarm-notes
|
Enables or disables the ability to overwrite alarm notes created by another user.
|
overwrite-circuit-notes
|
Enables or disables the ability to overwrite circuit notes created by another user.
|
ne-name-truncation
|
Allows you to specify how node names longer than 25 characters are truncated in the Network Map. If a string is longer than 25 characters, the first 22 characters display followed by an ellipsis (...).You can choose to truncate the first or last characters of the node name.
|
ui (continued)
|
ne-no-topo-hosts
|
Allows you to manage the number of Cisco Transport Controller (CTC) instances for optimal CTC performance. The default is ten ONS 15327 or ONS 15454 NEs. Although CTM can support up to 1,000 ONS 15327 or ONS 15454 NEs, CTC cannot effectively manage more than a small subset of these NEs. Consequently, the CTM domain must be partitioned into smaller CTC domains with one instance of CTC launched per CTC domain. The specified number of ONS 15327 or ONS 15454 NEs determines the number of gateway network elements (GNEs), or topology hosts, that constitute each CTC management domain. CTC uses the GNEs provided to discover and display other nodes that are physically connected to the GNEs. For example, if each ONS 15327 or ONS 15454 ring contains 3 NEs (including the GNE), CTC discovers and manages 3 x 10 = 30 nodes when the value is set to 10. In environments where most ONS 15327 or ONS 15454 rings or subnetworks contain 10 to 16 NEs, set this number to a smaller value, such as 3.
|
clear-unack-alarms
|
(Not used)
|
ne
|
debug-telnet-port
|
(Not used)
|
debug
|
logging-option
|
Enables ability to change logging library. Values are: JDK, Log4j and VWDebug.
|
log-buf-size
|
Maximum buffer size when logging is done using JDK or Log4j.
|
vwdebug-log-buf-size
|
Maximum buffer size when logging is done using VW debug.
|
vwdebug-log-idle-time
|
Maximum time the log strings are kept in the VW debug queue.
|
module-error-log-on
|
Indication whether error logging is on for the particular module.
|
max-log-directory-size
|
Maximum size for the log directory.
|
max-log-number-of-files
|
Maximum number of files allowed in logging directory.
|
module_config_level
|
Trace level for module.
|
module_jdaq_level
|
module_fm_level
|
module_iptl1_level
|
module_jmoco_level
|
module_main_level
|
module_oss_level
|
module_parser_level
|
module_pm_level
|
module_poller_level
|
module_snmp_level
|
module_sw_level
|
module_gwtl1_level
|
module_telnet_tunnel_level
|
module_snmp_tunnel_level
|
module_na_level
|
module_platform_level
|
module_util_level
|
module_ne_level
|
module_gwcorba_level
|
module_data_level
|
module_sm_level
|
module_csm_level
|
server-monitor
|
monitoring-enabled
|
Disables or enables monitoring.
|
no-of-threads
|
Number of threads used by monitoring.
|
polling-period
|
Frequency at which monitoring is done.
|
Disk_Usage_Enabled
|
Enables disk monitoring.
|
Disk_Usage_Critical
|
Critical threshold value for disk usage.
|
Disk_Usage_Major
|
Major threshold value for disk usage.
|
Disk_Usage_Minor
|
Minor threshold value for disk usage.
|
Disk_Usage_Units
|
Units in which disk usage is measured.
|
Memory_Usage_SWAP_Enabled
|
Enables monitoring for SWAP.
|
Memory_Usage_SWAP_Critical
|
Critical threshold value for SWAP usage.
|
Memory_Usage_SWAP_Major
|
Major threshold value for SWAP usage.
|
Memory_Usage_SWAP_Minor
|
Minor threshold value for SWAP usage.
|
Memory_Usage_SWAP_Units
|
Units in which SWAP usage is measured.
|
Memory_Usage_RAM_Enabled
|
Enables monitoring for RAM.
|
Memory_Usage_RAM_Critical
|
Critical threshold value for memory usage.
|
Memory_Usage_RAM_Major
|
Major threshold value for memory usage.
|
Memory_Usage_RAM_Minor
|
Minor threshold value for memory usage.
|
Memory_Usage_RAM_Units
|
Units in which memory usage is measured.
|
server-monitor (continued)
|
CPU_Usage_Enabled
|
Enables monitoring for CPU usage.
|
CPU_Usage_Critical
|
Critical threshold value for CPU usage.
|
CPU_Usage_Major
|
Major threshold value for CPU usage.
|
CPU_Usage_Minor
|
Minor threshold value for CPU usage.
|
CPU_Usage_Units
|
Units in which CPU usage is measured.
|
Prune_Time_Audit_Log_Enabled
|
Enables monitoring for prune time audit log.
|
Prune_Time_Audit_Log_Critical
|
Critical threshold value for prune time audit log.
|
Prune_Time_Audit_Log_Major
|
Major threshold value for prune time audit log.
|
Prune_Time_Audit_Log_Minor
|
Minor threshold value for prune time audit log.
|
Prune_Time_Audit_Log_Units
|
Units in which prune time audit log is measured.
|
Prune_Time_Error_Log_Enabled
|
Enables monitoring for prune time error log.
|
Prune_Time_Error_Log_Critical
|
Critical threshold value for prune time error log.
|
Prune_Time_Error_Log_Major
|
Major threshold value for prune time error log.
|
Prune_Time_Error_Log_Minor
|
Minor threshold value for prune time error log.
|
Prune_Time_Error_Log_Units
|
Units in which prune time error log is measured.
|
Prune_Time_Audit_Trail_Log_
Enabled
|
Enables monitoring for prune time audit trail log.
|
Prune_Time_Audit_Trail_Log_
Critical
|
Critical threshold value for prune time audit trail log.
|
Prune_Time_Audit_Trail_Log_Major
|
Major threshold value for prune time audit trail log.
|
Prune_Time_Audit_Trail_Log_Minor
|
Minor threshold value for prune time audit trail log.
|
Prune_Time_Audit_Trail_Log_Units
|
Units in which prune time audit trail log is measured.
|
server-monitor (continued)
|
Prune_Time_Purge_NE_Enabled
|
Enables monitoring for prune time purge NE.
|
Prune_Time_Purge_NE_Critical
|
Critical threshold value for prune time purge NE.
|
Prune_Time_Purge_NE_Major
|
Major threshold value for prune time purge NE.
|
Prune_Time_Purge_NE_Minor
|
Minor threshold value for prune time purge NE.
|
Prune_Time_Purge_NE_Units
|
Units in which prune time purge NE is measured.
|
Prune_Time_PM_Enabled
|
Enables monitoring for prune time PM.
|
Prune_Time_PM_Critical
|
Critical threshold value for prune time PM.
|
Prune_Time_PM_Major
|
Major threshold value for prune time PM.
|
Prune_Time_PM_Minor
|
Minor threshold value for prune time PM.
|
Prune_Time_PM_Units
|
Units in which prune time PM is measured.
|
Prune_Time_FM_Enabled
|
Enables monitoring for prune time FM.
|
Prune_Time_FM_Critical
|
Critical threshold value for prune time FM.
|
Prune_Time_FM_Major
|
Major threshold value for prune time FM.
|
Prune_Time_FM_Minor
|
Minor threshold value for prune time FM.
|
Prune_Time_FM_Units
|
Units in which prune time FM is measured.
|
Prune_Time_Server_Monitor_Enabled
|
Enables monitoring for prune time server monitor.
|
Prune_Time_Server_Monitor_Critical
|
Critical threshold value for prune time server monitor.
|
Prune_Time_Server_Monitor_Major
|
Major threshold value for prune time server monitor.
|
server-monitor (continued)
|
Prune_Time_Server_Monitor_Minor
|
Minor threshold value for prune time server monitor.
|
Prune_Time_Server_Monitor_Units
|
Units in which prune time server monitor is measured.
|
Prune_Time_Job_Monitor_Enabled
|
Enables monitoring for prune time job monitor.
|
Prune_Time_Job_Monitor_Critical
|
Critical threshold value for prune time job monitor.
|
Prune_Time_Job_Monitor_Major
|
Major threshold value for prune time job monitor.
|
Prune_Time_Job_Monitor_Minor
|
Minor threshold value for prune time job monitor.
|
Prune_Time_Job_Monitor_Units
|
Units in which prune time job monitor is measured.
|
PM_Collection_Time_Enabled
|
Enables monitoring for PM collection time.
|
PM_Collection_Time_Critical
|
Critical threshold value for PM collection time.
|
PM_Collection_Time_Major
|
Major threshold value for PM collection time.
|
PM_Collection_Time_Minor
|
Minor threshold value for PM collection time.
|
PM_Collection_Time_Units
|
Units in which PM collection time is measured.
|
Base_Circuit_Creation_Time_Enabled
|
Enables monitoring for base circuit creation time.
|
Base_Circuit_Creation_Time_Critical
|
Critical threshold value for base circuit creation time.
|
Base_Circuit_Creation_Time_Major
|
Major threshold value for base circuit creation time.
|
Base_Circuit_Creation_Time_Minor
|
Minor threshold value for base circuit creation time.
|
Base_Circuit_Creation_Time_Units
|
Units in which base circuit creation time is measured.
|
Circuit_Creation_Time_Per_Hop_
Enabled
|
Enables monitoring for circuit creation time.
|
Circuit_Creation_Time_Per_Hop_
Critical
|
Critical threshold value for circuit creation time.
|
server-monitor (continued)
|
Circuit_Creation_Time_Per_Hop_
Major
|
Major threshold value for circuit creation time.
|
Circuit_Creation_Time_Per_Hop_
Minor
|
Minor threshold value for circuit creation time.
|
Circuit_Creation_Time_Per_Hop_
Units
|
Units in which circuit creation time is measured.
|
NE_Synch_Time_Enabled
|
Enables monitoring for NE synch time.
|
NE_Synch_Time_Critical
|
Critical threshold value for NE synch time.
|
NE_Synch_Time_Major
|
Major threshold value for NE synch time.
|
NE_Synch_Time_Minor
|
Minor threshold value for NE synch time.
|
NE_Synch_Time_Units
|
Units in which NE synch time is measured.
|
Config_Resynch_Time_Enabled
|
Enables monitoring for config resynch time.
|
Config_Resynch_Time_Critical
|
Critical threshold for config resynch time.
|
Config_Resynch_Time_Major
|
Major threshold for config resynch time.
|
Config_Resynch_Time_Minor
|
Minor threshold for config resynch time.
|
Config_Resynch_Time_Units
|
Units in which config resynch time is measured.
|
critical-process
|
SMService
|
Indicates if this process is critical or non-critical.
|
OracleService
|
OSAgent
|
ons15454-ne
|
ons15454-pm
|
ons15200-ne
|
ons155xx-ne
|
ons155xx-pm
|
ons15800-ne
|
ons158xx-pm
|
ons15801-ne
|
ons15808-ne
|
ons15454sdh-ne
|
ons15454sdh-pm
|
ons15216-ne
|
ons15600-pm
|
ons15302-ne
|
ons15305-ne
|
ons1530x-pm
|
snmp-trap-service
|
gw-corba-service
|
gwtl1-service
|
database
|
db-prune-db05-enabled
|
Indicates whether pruning of archive log directory /db05 is enabled or not (default is not).
|
db-prune-db05-threshold
|
Pruning of /db05 will happen if the used capacity of /db05 crosses the threshold value (default value is 80%).
|
db-prune-db05-backupdirectory
|
Backup directory of /db05 (default is /ctm_backup).
|
db-prune-db05-polling-period
|
Interval of pruning /db05 if the threshold value is exceeded (default is 15 minutes).
|
db-archive-pm-days
|
How many days of PM will be kept in the db (default is 7 days).
|
db-archive-fm-days
|
How many days of FM will be kept in the db (default is 7 days).
|
database (continued)
|
db-archive-auditlog-days
|
How many days of audit log will be kept in the db (default is 7 days).
|
db-archive-errorlog-days
|
How many days of error log will be kept in the db (default is 7 days).
|
db-archive-audittrail-days
|
How many days of audit trail will be kept in the db (default is 7 days).
|
db-archive-server-monitor-days
|
How many days of server monitor entries will be kept in the db (default is 7 days).
|
db-archive-server-jobmonitor-days
|
How many days of job monitor entries will be kept in the db (default is 7 days).
|
db-prune-pm-enabled
|
Flag to check if the pruning of data is enabled.
|
db-prune-fm-enabled
|
db-prune-auditlog-enabled
|
db-prune-errorlog-enabled
|
db-prune-audittrail-enabled
|
db-prune-server-monitor-enabled
|
db-prune-server-jobmonitor-enabled
|
daily-prune-pm-time
|
The time on a day when data will be pruned.
|
daily-prune-fm-time
|
daily-prune-errorlog-time
|
daily-prune-auditlog-time
|
daily-prune-audittrail-time
|
daily-prune-server-monitor-time
|
daily-prune-server-jobmonitor-time
|
db-connection-pool-size-pmservice
|
Number of connections in JDBC connection pool for PM service (default is 10).
|
db-server-configuration
|
CTM db and server configuration type (default type is small).
|
dbname
|
The name for the database, which is based on the release (for example, CTM5_0 for 5.0).
|
database (continued)
|
dbversion
|
The version indicates the release (for example, 5.0).
|
db-diskspace-critical-threshold
|
Critical alarm is raised when used disk space crosses the threshold (default is 90%).
|
db-diskspace-major-threshold
|
Major alarm is raised when used disk space crosses the threshold (default is 80%).
|
db-diskspace-minor-threshold
|
Minor alarm is raised when used disk space crosses the threshold (default is 70%).
|
ha
|
max-retries
|
If the first backup CTM server is not available, this field provides the number of times the client should retry logging in before moving to the next server on the list.
|
wait-time
|
If disruption to the primary CTM server occurs, the Wait Time field provides the number of seconds the client waits before attempting to log into the backup server.
|
server-name-list
|
Lists the CTM servers that CTM clients will log into if access to the primary CTM server is disrupted.
|
