Table 10-2 Cisco IOS V2 Traps
Trap Name
|
Trap OID
|
Sub Type Varbind OID
|
Sub Type Varbind Value
|
Description
|
Short Description
|
cbfDefineFileCompletion
|
.1.3.6.1.4.1.9.9.81.2.0.1
|
N/A
|
N/A
|
A cbfDefineFileCompletion notification is sent on the following conditions:
• Completion of a file consumption operation in case of ephemeral files.
•Completion of file creation operation in case of volatile or permanent files.
•Any error during file creation.
|
CBF File operation state indicator
|
cbgpBackwardTransition
|
.1.3.6.1.4.1.9.9.187.0.2
|
NA
|
NA
|
The cbgpBackwardTransition Event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state. The bgpPeerRemoteAddr value is attached to the notification object ID.
|
Cisco BGP backward transition trap
|
cbgpFsmStateChange
|
.1.3.6.1.4.1.9.9.187.0.1
|
1.3.6.1.4.1.9.9.187.0.2
|
= 1
|
The BGP cbgpFsmStateChange notification is generated for every BGP FSM state change.
|
Cisco BGP down trap
|
cbgpFsmStateChange
|
.1.3.6.1.4.1.9.9.187.0.1
|
1.3.6.1.4.1.9.9.187.0.2
|
= 6
|
The BGP cbgpFsmStateChange notification is generated for every BGP FSM state change.
|
Cisco BGP established trap
|
cbgpFsmStateChange
|
.1.3.6.1.4.1.9.9.187.0.1
|
1.3.6.1.4.1.9.9.187.0.2
|
!= (1 or 6)
|
The BGP cbgpFsmStateChange notification is generated for every BGP FSM state change.
|
Cisco BGP FSM state changed trap
|
cbgpPrefixThresholdExceeded
|
.1.3.6.1.4.1.9.9.187.0.3
|
NA
|
NA
|
This notification is generated when prefix count exceeds the configured warning threshold on a session for an address family
|
Cisco BGP prefix threshold exceeded
|
cbgpPrefixThresholdClear
|
.1.3.6.1.4.1.9.9.187.0.4
|
NA
|
NA
|
The cbgpPrefixThresholdClear notification is generated when prefix count drops below the configured clear threshold on a session for an address familly once cbgpPrefixThresholdExceeded is generated. This won't be generated if the peer session goes down after the generation of bgpPrefixThresholdExceeded. The bgpPeerRemoteAddr, bgpPeerAddrFamilyAfi and cbgpPeerAddrFamilySafi values are attached to the notification object ID.
|
Cisco BGP prefix threshold clear
|
ccCopyCompletion
|
.1.3.6.1.4.1.9.9.96.2.1.1
|
N/A
|
N/A
|
A ccCopyCompletion trap is sent at the completion of a config-copy request. The ccCopyFailCause is not instantiated, and hence not included in a trap, when the ccCopyState is success
|
Config-copy request completion
|
ciscoConfigManEvent
|
.1.3.6.1.4.1.9.9.43.2.0.1
|
N/A
|
N/A
|
Notification of a configuration management event as recorded in ccmHistoryEventTable.
|
Cisco Configuration management event notification
|
cefcFanTrayStatusChange
|
.1.3.6.1.4.1.9.9.117.2.0.6
|
1.3.6.1.4.1.9.9.117.1.4.1.1.1
|
!=2
|
This notification is generated when the value of cefcFanTrayOperStatus changes.
|
cefc Fan-tray oper status down
|
cefcFanTrayStatusChange
|
.1.3.6.1.4.1.9.9.117.2.0.6
|
1.3.6.1.4.1.9.9.117.1.4.1.1.1
|
=2
|
This notification is generated when the value of cefcFanTrayOperStatus changes.
|
cefc fan-tray oper status up
|
cefcFRUInserted
|
.1.3.6.1.4.1.9.9.117.2.0.3
|
N/A
|
N/A
|
The cecfFRUInserted notification indicates that a FRU was inserted. The varbind for this notification indicates the entPhysicalIndex of the inserted FRU, and the entPhysicalIndex of the FRU's container.
|
cefc FRU inserted
|
cefcFRURemoved
|
.1.3.6.1.4.1.9.9.117.2.0.4
|
N/A
|
N/A
|
The cefcFRURemoved notification indicates that a FRU was removed. The varbind for this notification indicates the entPhysicalIndex of the removed FRU, and the entPhysicalIndex of the FRU's container.
|
cefc FRU removed
|
cefcModuleStatusChange
|
.1.3.6.1.4.1.9.9.117.2.0.1
|
1.3.6.1.4.1.9.9.117.1.2.1.1.2
|
!=2
|
This notification is generated when the value of cefcModuleOperStatus changes. It can be utilized by an NMS to update the status of the module it is managing.
|
cefc module oper status down
|
cefcModuleStatusChange
|
.1.3.6.1.4.1.9.9.117.2.0.1
|
1.3.6.1.4.1.9.9.117.1.2.1.1.2
|
=2
|
This notification is generated when the value of cefcModuleOperStatus changes. It can be utilized by an NMS to update the status of the module it is managing.
|
cefc module oper status up
|
cefcPowerStatusChange
|
.1.3.6.1.4.1.9.9.117.2.0.2
|
1.3.6.1.4.1.9.9.117.1.1.2.1.2
|
!=2
|
The cefcFRUPowerStatusChange notification indicates that the power status of a FRU has changed. The varbind for this notification indicates the entPhysicalIndex of the FRU, and the new operational-status of the FRU.
|
cefc Power status down
|
cefcPowerStatusChange
|
.1.3.6.1.4.1.9.9.117.2.0.2
|
1.3.6.1.4.1.9.9.117.1.1.2.1.2
|
=2
|
The cefcFRUPowerStatusChange notification indicates that the power status of a FRU has changed. The varbind for this notification indicates the entPhysicalIndex of the FRU, and the new operational-status of the FRU.
|
cefc Power status up
|
entSensorThresholdNotification
|
.1.3.6.1.4.1.9.9.91.2.0.1
|
N/A
|
N/A
|
The sensor value crossed the threshold listed in entSensorThresholdTable. This notification is generated once each time the sensor value crosses the threshold
|
sensor value crossed threshold in entSensorThresholdTable
|
ciscoFlashCopyCompletionTrap
|
.1.3.6.1.4.1.9.9.10.1.3.0.1
|
1.3.6.1.4.1.9.9.10.1.2.1.1.8
|
!= (0 or 1 or 2)
|
A ciscoFlashCopyCompletionTrap is sent at the completion of a flash copy operation if such a trap was requested when the operation was initiated.
|
Cisco flash copy failed
|
ciscoFlashCopyCompletionTrap
|
.1.3.6.1.4.1.9.9.10.1.3.0.1
|
1.3.6.1.4.1.9.9.10.1.2.1.1.8
|
=2
|
A ciscoFlashCopyCompletionTrap is sent at the completion of a flash copy operation if such a trap was requested when the operation was initiated.
|
Cisco flash copy completion
|
ciscoFlashCopyCompletionTrap
|
.1.3.6.1.4.1.9.9.10.1.3.0.1
|
1.3.6.1.4.1.9.9.10.1.2.1.1.8
|
= (0 or 1)
|
A ciscoFlashCopyCompletionTrap is sent at the completion of a flash copy operation if such a trap was requested when the operation was initiated.
|
Cisco flash copy in progress
|
ciscoFlashDeviceChangeTrap
|
.1.3.6.1.4.1.9.9.10.1.3.0.4
|
N/A
|
N/A
|
A ciscoFlashDeviceChangeTrap is sent whenever a removable Flash device is inserted or removed.
|
Cisco Flash device changed
|
ciscoFlashDeviceInsertedNotif
|
.1.3.6.1.4.1.9.9.10.1.3.0.5
|
N/A
|
N/A
|
A ciscoFlashDeviceInsertedNotif notification is sent whenever a removable Flash device is inserted.
|
Cisco Flash device inserted
|
ciscoFlashDeviceRemovedNotif
|
.1.3.6.1.4.1.9.9.10.1.3.0.6
|
N/A
|
N/A
|
A ciscoFlashDeviceRemovedNotif notification is sent whenever a removable Flash device is removed.
|
Cisco Flash device removed
|
ciscoFlashDeviceInsertedNotifRev1
|
.1.3.6.1.4.1.9.9.10.1.3.0.7
|
N/A
|
N/A
|
This notification is sent whenever a removable Flash device is inserted. The notification deprecates ciscoFlashDeviceInsertedNotif since it uses ciscoFlashDeviceName as a varbind, which is deprecated.
|
Cisco Flash device inserted
|
ciscoFlashDeviceRemovedNotifRev1
|
.1.3.6.1.4.1.9.9.10.1.3.0.8
|
N/A
|
N/A
|
This notification is sent whenever a removable Flash device is removed. It deprecates ciscoFlashDeviceRemovedNotif since it uses ciscoFlashDeviceName as a varbind which is deprecated.
|
Cisco Flash device removed
|
ciscoFlashMiscOpCompletionTrap
|
.1.3.6.1.4.1.9.9.10.1.3.0.3
|
1.3.6.1.4.1.9.9.10.1.2.3.1.4
|
=2
|
This notification is sent at the completion of a miscellaneous flash operation (enumerated in ciscoFlashMiscOpCommand) if such a trap was requested when the operation was initiated.
|
Cisco Flash miscellaneous operation completed
|
ciscoFlashMiscOpCompletionTrap
|
.1.3.6.1.4.1.9.9.10.1.3.0.3
|
1.3.6.1.4.1.9.9.10.1.2.3.1.4
|
=2
|
This notification is sent at the completion of a miscellaneous flash operation (enumerated in ciscoFlashMiscOpCommand) if such a trap was requested when the operation was initiated.
|
Cisco Flash partitioning Completed
|
ciscoFlashMiscOpCompletionTrap
|
.1.3.6.1.4.1.9.9.10.1.3.0.3
|
1.3.6.1.4.1.9.9.10.1.2.3.1.4
|
=1
|
This notification is sent at the completion of a miscellaneous flash operation (enumerated in ciscoFlashMiscOpCommand) if such a trap was requested when the operation was initiated.
|
Cisco Flash miscellaneous operation in progress
|
chassisAlarmOff
|
1.3.6.1.4.1.9.5.0.6
|
N/A
|
N/A
|
Chassis alarm trap
|
chassis alarm off
|
chassisAlarmOn
|
1.3.6.1.4.1.9.5.0.5
|
N/A
|
N/A
|
Chassis alarm trap
|
chassis alarm on
|
cPimNbrLoss
|
.1.3.6.1.4.1.9.10.119.0.2
|
N/A
|
N/A
|
A cPimNbrLoss trap signifies the loss of an adjacency with a neighbor. This trap should be generated when the neighbor timer expires, and the router has no other neighbors on the same interface with a lower IP address than itself.
|
Cisco PIM neighbor lost
|
ciscoPingCompletion
|
.1.3.6.1.4.1.9.9.16.2.0.1
|
N/A
|
N/A
|
A ciscoPingCompleted trap is sent at the completion of a sequence of pings if such a trap was requested when the sequence was initiated.
|
Cisco ping completion
|
rttMonNotification
|
.1.3.6.1.4.1.9.9.42.2.0.5
|
N/A
|
N/A
|
A rttMonNotification indicates the occurrence of a threshold violation, and it indicates the previous violation has subsided for a subsequent operation.
|
RTT threshold violation or clearance
|
ciscoSonetSectionStatusChange
|
.1.3.6.1.4.1.9.9.126.0.1
|
1.3.6.1.2.1.10.39.1.2.1.1.1
|
!=1
|
This notification is generated whenever the value of sonetSectionCurrentStatus changes to value more than 1.
|
Cisco Sonet section status changed to error
|
ciscoSonetSectionStatusChange
|
.1.3.6.1.4.1.9.9.126.0.1
|
1.3.6.1.2.1.10.39.1.2.1.1.1
|
=1
|
This notification is generated whenever the value of sonetSectionCurrentStatus changes to value 1.
|
Cisco Sonet section status changed to clear
|
ciscoSonetLineStatusChange
|
.1.3.6.1.4.1.9.9.126.0.2
|
1.3.6.1.2.1.10.39.1.3.1.1.1
|
!=1
|
This notification is generated whenever the value of sonetLineCurrentStatus changes to value more than 1.
|
Cisco Sonet line status changed to error
|
ciscoSonetLineStatusChange
|
.1.3.6.1.4.1.9.9.126.0.2
|
1.3.6.1.2.1.10.39.1.3.1.1.1
|
=1
|
This notification is generated whenever the value of sonetLineCurrentStatus changes to value 1.
|
Cisco Sonet line status changed to clear
|
ciscoSonetPathStatusChange
|
.1.3.6.1.4.1.9.9.126.0.3
|
1.3.6.1.2.1.10.39.2.1.1.1.2
|
!=1
|
This notification is generated whenever the value of sonetPathCurrentStatus changes to value more than 1.
|
Cisco Sonet path status changed to error
|
ciscoSonetPathStatusChange
|
.1.3.6.1.4.1.9.9.126.0.3
|
1.3.6.1.2.1.10.39.2.1.1.1.2
|
=1
|
This notification is generated whenever the value of sonetPathCurrentStatus changes to value 1.
|
Cisco Sonet path status changed to clear
|
mplsLdpFailedInitSessionThresholdExceeded
|
.1.3.6.1.4.1.9.10.65.2.0.1
|
N/A
|
N/A
|
This notification is generated when the value of the `mplsLdpEntityPVLimitMismatchTrapEnable' object is `enabled(1)' and the value of the object, `mplsLdpEntityFailedInitSessionThreshold' has been exceeded.
|
MPLS LDP init session threshold exceeded Trap
|
mplsLdpSessionDown
|
.1.3.6.1.4.1.9.10.65.2.0.4
|
N/A
|
N/A
|
Generation of this trap occurs when the `mplsLdpSessionUpDownTrapEnable' object is `enabled(1)' and the value of mplsLdpSessionState changes from `operational(5)' to any other state.
|
MPLS LDP session down Trap
|
mplsLdpSessionUp
|
.1.3.6.1.4.1.9.10.65.2.0.3
|
N/A
|
N/A
|
Generation of this trap occurs when the `mplsLdpSessionUpDownTrapEnable' object is `enabled(1)' and the value of mplsLdpSessionState changes from any state accept `nonexistent(1)' to `operational'.
|
MPLS LDP session up Trap
|
mplsTunnelUp
|
.1.3.6.1.3.95.3.0.1
|
N/A
|
N/A
|
This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to leave the down state and transition into some other state (but not into the notPresent state). This other state is indicated by the included value of mplsTunnelOperStatus.
|
MPLS-TE tunnel up
|
mplsTunnelDown
|
.1.3.6.1.3.95.3.0.2
|
N/A
|
N/A
|
This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to enter the down state from some other state (but not from the notPresent state). This other state is indicated by the included value of mplsTunnelOperStatus.
|
MPLS-TE tunnel down
|
mplsTunnelRerouted
|
.1.3.6.1.3.95.3.0.3
|
N/A
|
N/A
|
This notification is generated when a tunnel is rerouted or re-optimized. If the Actual Path is used, then this object MAY contain the new path for this tunnel some time after this trap is issued by the agent
|
MPLS-TE tunnel reoptimized
|
ciscoIpMRouteMissingHeartBeats
|
.1.3.6.1.4.1.9.10.2.3.1.0.1
|
N/A
|
N/A
|
A notification is sent if a multicast router with this feature enabled failed to receive configured number of heartbeat packets from heartbeat sources within a configured time interval
|
Failed receive multicast router heartbeat
|
ciscoRFProgressionNotif
|
1.3.6.1.4.1.9.9.176.2.0.2
|
N/A
|
N/A
|
VSL link goes down or one of the chassis reloads
|
Cisco VSS Shelf 1 is Disabled
|
ciscoRFProgressionNotif
|
1.3.6.1.4.1.9.9.176.2.0.2
|
N/A
|
N/A
|
VSL link goes down or one of the chassis reloads
|
Cisco VSS Shelf 1 is Standby Cold
|
ciscoRFProgressionNotif
|
1.3.6.1.4.1.9.9.176.2.0.2
|
N/A
|
N/A
|
VSL link goes down or one of the chassis reloads
|
Cisco VSS Shelf 1 is Standby Hot
|
ciscoRFProgressionNotif
|
1.3.6.1.4.1.9.9.176.2.0.2
|
N/A
|
N/A
|
VSL link goes down or one of the chassis reloads
|
Cisco VSS Shelf 2 is Disabled
|
ciscoRFProgressionNotif
|
1.3.6.1.4.1.9.9.176.2.0.2
|
N/A
|
N/A
|
VSL link goes down or one of the chassis reloads
|
Cisco VSS Shelf 2 is Standby Cold
|
ciscoRFProgressionNotif
|
1.3.6.1.4.1.9.9.176.2.0.2
|
N/A
|
N/A
|
VSL link goes down or one of the chassis reloads
|
Cisco VSS Shelf 2 is Standby Hot
|
cvsVSLConnectionChangeNotif
|
1.3.6.1.4.1.9.9.388.0.1
|
N/A
|
N/A
|
When VSL connection is down
|
VSL Connection Changed: Down
|
cvsVSLConnectionChangeNotif
|
1.3.6.1.4.1.9.9.388.0.1
|
N/A
|
N/A
|
When VSL connection is up
|
VSL Connection Changed: Up
|
rttMonTimeoutNotification
|
.1.3.6.1.4.1.9.9.42.2.0.2
|
N/A
|
N/A
|
This Notification indicates the occurrence of a timeout for a RTT operation
|
RTT Operation Timeout
|
rttMonThresholdNotification
|
.1.3.6.1.4.1.9.9.42.2.0.3
|
N/A
|
N/A
|
This Notification indicates the occurrence of a threshold violation for a RTT operation
|
RTT Operation Threshold Violation
|
topologyChange
|
.1.3.6.1.2.1.17.0.2
|
N/A
|
N/A
|
This Notification is sent by a bridge when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state.
|
dot1qBridge trap
|
cEtherCfmCcMepUp
|
.1.3.6.1.4.1.9.9.461.0.0.1
|
N/A
|
N/A
|
This notification is generated in the following cases:
•When a remote MEP first comes up, that is when we receive CC message from that MEP for the first time.
•When the device receives a CC message from a MEP for which t has an expired CCDB entry.
•When a CC message is received for a remote MEP for which the device already has a CCDB entry and the port-state in the received CC message is different from the cached previous state
|
Mep up trap
|
cEtherCfmCcMepDown
|
.1.3.6.1.4.1.9.9.461.0.0.2
|
N/A
|
N/A
|
This notification is generated when a remote MEP goes down, namely, the entry in CCDB corresponding to this MEP times out or the device receives a CC message with zero hold-time
|
Mep down trap
|
coldStart
|
.1.3.6.1.2.1.11.0.0
|
N/A
|
N/A
|
This trap signifies that the sending protocol entity is reinitializing itself such that the agent's configuration or the protocol entity implementation may be altered.
|
Cold start trap
|
cHsrpStateChange
|
1.3.6.1.4.1.9.9.106.2.0.1
|
1.3.6.1.4.1.9.9.106.1.2.1.1.15
|
= 5
|
A cHsrpStateChange notification is sent when a cHsrpGrpStandbyState transitions to either active or standby state, or leaves active or standby state. There will be only one notification issued when the state change is from standby to active and vice versa.
|
Cisco hsrp state standby
|
cHsrpStateChange
|
1.3.6.1.4.1.9.9.106.2.0.1
|
1.3.6.1.4.1.9.9.106.1.2.1.1.15
|
= ^
|
A cHsrpStateChange notification is sent when a cHsrpGrpStandbyState transitions to either active or standby state, or leaves active or standby state. There will be only one notification issued when the state change is from standby to active and vice versa.
|
Cisco hsrp state non active
|
cHsrpStateChange
|
1.3.6.1.4.1.9.9.106.2.0.1
|
1.3.6.1.4.1.9.9.106.1.2.1.1.15
|
= 6
|
Sent when a cHsrpGrpStandbyState transitions to either active or standby state, or leaves active or standby state. There will be only one notification issued when the state change is from standby to active and vice versa.
|
Cisco hsrp state active
|
ciscoEnvMonFanNotification
|
1.3.6.1.4.1.9.9.13.3.0.4
|
1.3.6.1.4.1.9.9.13.1.4.1.3
|
= 3
|
Sent if any one of the fans in the fan array (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Fan Critical Trap
|
ciscoEnvMonFanNotification
|
1.3.6.1.4.1.9.9.13.3.0.4
|
1.3.6.1.4.1.9.9.13.1.4.1.3
|
= 1
|
Sent if any one of the fans in the fan array (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Fan Normal Trap
|
ciscoEnvMonFanNotification
|
1.3.6.1.4.1.9.9.13.3.0.4
|
1.3.6.1.4.1.9.9.13.1.4.1.3
|
= 6
|
Sent if any one of the fans in the fan array (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Fan Not Functioning Trap
|
ciscoEnvMonFanNotification
|
1.3.6.1.4.1.9.9.13.3.0.4
|
1.3.6.1.4.1.9.9.13.1.4.1.3
|
= 5
|
Sent if any one of the fans in the fan array (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Fan Not Present Trap
|
ciscoEnvMonFanNotification
|
1.3.6.1.4.1.9.9.13.3.0.4
|
1.3.6.1.4.1.9.9.13.1.4.1.3
|
= 4
|
Sent if any one of the fans in the fan array (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Fan Shutdown Trap
|
ciscoEnvMonFanNotification
|
1.3.6.1.4.1.9.9.13.3.0.4
|
1.3.6.1.4.1.9.9.13.1.4.1.3
|
= 2
|
Sent if any one of the fans in the fan array (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Fan Warning Trap
|
ciscoEnvMonRedundantSupplyNotification
|
1.3.6.1.4.1.9.9.13.3.0.5
|
1.3.6.1.4.1.9.9.13.1.5.1.3
|
= 3
|
Sent if the redundant power supply (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Redundant PowerSupply Critical Trap
|
ciscoEnvMonRedundantSupplyNotification
|
1.3.6.1.4.1.9.9.13.3.0.5
|
1.3.6.1.4.1.9.9.13.1.5.1.3
|
= 1
|
Sent if the redundant power supply (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Redundant PowerSupply Normal Trap
|
ciscoEnvMonRedundantSupplyNotification
|
1.3.6.1.4.1.9.9.13.3.0.5
|
1.3.6.1.4.1.9.9.13.1.5.1.3
|
= 6
|
Sent if the redundant power supply (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Redundant PowerSupply Not Functioning Trap
|
ciscoEnvMonRedundantSupplyNotification
|
1.3.6.1.4.1.9.9.13.3.0.5
|
1.3.6.1.4.1.9.9.13.1.5.1.3
|
= 5
|
Sent if the redundant power supply (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Redundant PowerSupply Not Present Trap
|
ciscoEnvMonRedundantSupplyNotification
|
1.3.6.1.4.1.9.9.13.3.0.5
|
1.3.6.1.4.1.9.9.13.1.5.1.3
|
= 4
|
Sent if the redundant power supply (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Redundant PowerSupply Shutdown Trap
|
ciscoEnvMonRedundantSupplyNotification
|
1.3.6.1.4.1.9.9.13.3.0.5
|
1.3.6.1.4.1.9.9.13.1.5.1.3
|
= 2
|
Sent if the redundant power supply (where existent) fails. Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Redundant PowerSupply Warning Trap
|
ciscoEnvMonTemperatureNotification
|
1.3.6.1.4.1.9.9.13.3.0.3
|
1.3.6.1.4.1.9.9.13.1.3.1.6
|
= 3
|
Sent if the temperature measured at a given testpoint is outside the normal range for the testpoint (i.e., is at the warning, critical, or shutdown stage). Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Critical Temperature
|
ciscoEnvMonTemperatureNotification
|
1.3.6.1.4.1.9.9.13.3.0.3
|
1.3.6.1.4.1.9.9.13.1.3.1.6
|
= 1
|
Sent if the temperature measured at a given testpoint is outside the normal range for the testpoint (i.e., is at the warning, critical, or shutdown stage). Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does the ciscoEnvMonShutdownNotification.
|
Normal Temperature
|
ciscoEnvMonTemperatureNotification
|
1.3.6.1.4.1.9.9.13.3.0.3
|
1.3.6.1.4.1.9.9.13.1.3.1.6
|
= 6
|
Sent if the temperature measured at a given testpoint is outside the normal range for the testpoint (i.e., is at the warning, critical, or shutdown stage). Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Not Functioning
|
ciscoEnvMonTemperatureNotification
|
1.3.6.1.4.1.9.9.13.3.0.3
|
1.3.6.1.4.1.9.9.13.1.3.1.6
|
= 5
|
Sent if the temperature measured at a given testpoint is outside the normal range for the testpoint (i.e. is at the warning, critical, or shutdown stage). Since such a Notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does the ciscoEnvMonShutdownNotification.
|
Not Present
|
ciscoEnvMonTemperatureNotification
|
1.3.6.1.4.1.9.9.13.3.0.3
|
1.3.6.1.4.1.9.9.13.1.3.1.6
|
= 4
|
A ciscoEnvMonTemperatureNotification is sent if the temperature measured at a given testpoint is outside the normal range for the testpoint (i.e. is at the warning, critical, or shutdown stage). Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
Critical Temperature- Device Shutdown
|
ciscoEnvMonTemperatureNotification
|
1.3.6.1.4.1.9.9.13.3.0.3
|
1.3.6.1.4.1.9.9.13.1.3.1.6
|
= 2
|
Sent if the temperature measured at a given testpoint is outside the normal range for the testpoint (i.e. is at the warning, critical, or shutdown stage). Since this notification is usually generated before the shutdown state is reached, it can convey more data and has a better chance of being sent than does ciscoEnvMonShutdownNotification.
|
temperatureRising
|
newRoot
|
1.3.6.1.2.1.17.0.1
|
NA
|
NA
|
The newRoot trap indicates that the sending agent has become the new root of the Spanning Tree; the trap is sent by a bridge soon after its election as the new root, e.g., upon expiration of the Topology Change Timer, immediately subsequent to its election. Implementation of this trap is optional.
|
STP New Root Trap
|
stpxInconsistencyUpdate
|
1.3.6.1.4.1.9.9.82.2.0.1
|
1.3.6.1.4.1.9.9.82.1.3.1.1.3
|
=1
|
A stpxPortInconsistencyUpdate notification is sent by a bridge when an instance of stpxInconsistentState is created or destroyed. That is, when an inconsistency is discovered in the VLAN's Spanning Tree for a particular port, or when such an inconsistency disappears. Note that the trap is not sent if the port transitions between different types of inconsistency. The stpxInconsistentState value indicates the type of inconsistency which now exists/no longer exists for the relevant VLAN on the relevant port.
|
STPX Port Inconsistency discovered Trap
|
stpxInconsistencyUpdate
|
1.3.6.1.4.1.9.9.82.2.0.1
|
1.3.6.1.4.1.9.9.82.1.3.1.1.4
|
=2
|
A stpxPortInconsistencyUpdate notification is sent by a bridge when an instance of stpxInconsistentState is created or destroyed. That is, when an inconsistency is discovered in the VLAN's Spanning Tree for a particular port, or when such an inconsistency disappears. Note that the trap is not sent if the port transitions between different types of inconsistency. The stpxInconsistentState value indicates the type of inconsistency which now exists/no longer exists for the relevant VLAN on the relevant port.
|
STPX Port Inconsistency resolved Trap
|
stpxLoopInconsistencyUpdate
|
1.3.6.1.4.1.9.9.82.2.0.3
|
1.3.6.1.4.1.9.9.82.1.8.2.1.3
|
= 1
|
A stpxLoopInconsistencyUpdate notification is sent by a bridge when an instance of stpxLoopInconsistencyState is created or destroyed. That is, when an loop-inconsistency is discovered in the VLAN's or instance's Spanning Tree for a particular port, or when such a loop-inconsistency disappears. For creation, the value of stpxLoopInconsistencyState in the notification is true(1); for deletion, the value is false(2). The object value of stpxSpanningTreeType indicates which Spanning Tree protocol is running when an instance of stpxLoopInconsistencyState is created or destroyed.
|
STPX Loop Inconsistency Discovered Trap
|
stpxLoopInconsistencyUpdate
|
1.3.6.1.4.1.9.9.82.2.0.3
|
1.3.6.1.4.1.9.9.82.1.8.2.1.3
|
= 2
|
A stpxLoopInconsistencyUpdate notification is sent by a bridge when an instance of stpxLoopInconsistencyState is created or destroyed. That is, when an loop-inconsistency is discovered in the VLAN's or instance's Spanning Tree for a particular port, or when such a loop-inconsistency disappears. For creation, the value of stpxLoopInconsistencyState in the notification is true(1); for deletion, the value is false(2). The object value of stpxSpanningTreeType indicates which Spanning Tree protocol is running when an instance of stpxLoopInconsistencyState is created or destroyed.
|
STPX Loop Inconsistency Discovered Trap
|
stpxRootInconsistencyUpdate
|
1.3.6.1.4.1.9.9.82.2.0.2
|
1.3.6.1.4.1.9.9.82.1.5.2.1.3
|
= 1
|
A stpxRootInconsistencyUpdate notification is sent by a bridge when an instance of stpxRootInconsistencyState is created or destroyed. That is, when an root-inconsistency is discovered in the VLAN's or instance's Spanning Tree for a particular port, or when such an root-inconsistency disappears. For creation, the value of stpxRootInconsistencyState in the notification is true(1); for deletion, the value is false(2). The object value of stpxSpanningTreeType indicates which Spanning Tree protocol is running when an instance of stpxRootInconsistencyState is created or destroyed.
|
STPX Root Inconsistency Discovered Trap
|
stpxRootInconsistencyUpdate
|
1.3.6.1.4.1.9.9.82.2.0.2
|
1.3.6.1.4.1.9.9.82.1.5.2.1.3
|
= 2
|
A stpxRootInconsistencyUpdate notification is sent by a bridge when an instance of stpxRootInconsistencyState is created or destroyed. That is, when an root-inconsistency is discovered in the VLAN's or instance's Spanning Tree for a particular port, or when such an root-inconsistency disappears. For creation, the value of stpxRootInconsistencyState in the notification is true(1); for deletion, the value is false(2). The object value of stpxSpanningTreeType indicates which Spanning Tree protocol is running when an instance of stpxRootInconsistencyState is created or destroyed.
|
STPX Root Inconsistency Resolved Trap
|
vtp Config Rev Number Error
|
1.3.6.1.4.1.9.9.46.2.0.1
|
NA
|
NA
|
A configuration revision number error notification signifies that a device has incremented its vtpConfigRevNumberErrors counter. Generation of this notification is suppressed if the vtpNotificationsEnabled has the value "false". The device must throttle the generation of consecutive vtpConfigRevNumberError notifications so that there is at least a five-second gap between notification of this type. When notification are throttled, they are dropped, not queued for sending at a future time. (Note that 'generating' a notification means sending to all configured recipients.)
|
vtp configuration revision number error trap
|
vtpConfigDigestError
|
1.3.6.1.4.1.9.9.46.2.0.2
|
NA
|
NA
|
A configuration digest error notification signifies that a device has incremented its vtpConfigDigestErrors counter. Generation of this notification is suppressed if the vtpNotificationsEnabled has the value 'false'. The device must throttle the generation of consecutive vtpConfigDigestError notifications so that there is at least a five-second gap between notification of this type. When notification are throttled, they are dropped, not queued for sending at a future time. (Note that 'generating' a notification means sending to all configured recipients).
|
vtp configuration digest error trap
|
cisco-EnvMon-Shutdown-Notification-Trap
|
1.3.6.1.4.1.9.9.13.3.0.1
|
NA
|
NA
|
Sent if the environmental monitor detects a testpoint reaching a critical state and is about to initiate a shutdown. This notification contains no objects so that it may be encoded and sent in the shortest amount of time possible. Even so, management applications should not rely on receiving such a notification as it may not be sent before the shutdown completes.
|
cisco EnvMon Shutdown Notification Trap
|
caem Temperature Notification
|
1.3.6.1.4.1.9.9.61.2.0.1
|
NA
|
NA
|
A caemTemperatureNotification is sent if the over-temperature condition is detected in the managed system. This is a replacement for the ciscoEnvMonTemperatureNotification trap because the information ciscoEnvMonTemperatureStatusValue required by the trap is not available in the managed system.
|
caem Temperature Notification Trap
|
caem Voltage Notification
|
1.3.6.1.4.1.9.9.61.2.0.2
|
NA
|
NA
|
Sent if the over-voltage condition is detected and ciscoEnvMonVoltageState is not set to "notPresent" in the managed system. This is a replacement for the ciscoEnvMonVoltageNotification trap because the information 'ciscoEnvMonVoltageStatusValue' required by the trap is not available in the managed system.
|
caem Voltage Notification Trap
|
cmn-Mac-Changed-Notification-Trap
|
1.3.6.1.4.1.9.9.215.2.0.1
|
NA
|
NA
|
This notification is generated when there is enough MAC address information to fully occupy a maximum size SNMP trap message. This notification is also generated when there is at least one MAC address changed or removed and the amount of time elapsed from the previous notification is greater than the maximum wait time denoted by cmnNotificationInterval object. If there are more MAC addresses information than can fit into one cmmHistTrapContent object, then multiple notifications will be generated.
|
cmn Mac Changed Notification Trap
|
cmn-Mac-Move-Notification-Trap
|
1.3.6.1.4.1.9.9.215.2.0.2
|
NA
|
NA
|
cmnMacMoveNotification is generated when a MAC address is moved between two interfaces.
|
cmn Mac Move Notification Trap
|
vtp VersionOne Device Detected
|
1.3.6.1.4.1.9.9.46.2.0.6
|
NA
|
NA
|
A VTP version one device detected notification is generated by a device when:
a) a management domain has been put into version 2 mode (as accessed by managementDomainVersionInUse.
b) 15 minutes has passed since a).
c) a version 1 PDU is detected on a trunk on the device that is in that management domain which has a lower revision number than the current configuration.
|
vtp VersionOne Device Detected trap
|
vtp Local Mode Changed
|
1.3.6.1.4.1.9.9.46.2.0.8
|
NA
|
NA
|
A vtpLocalModeChanged notification is generated by a device when the value of the object managementDomainLocalMode is changed.
|
vtp Local Mode Changed trap
|
vtp VersionInUse Changed
|
1.3.6.1.4.1.9.9.46.2.0.9
|
NA
|
NA
|
Sent by a device when the value of the object managementDomainVersionInUse is changed.
|
vtp VersionInUse Changed trap
|
trunking
|
1.3.6.1.4.1.9.9.46.2.0.7
|
1.3.6.1.4.1.9.9.46.1.6.1.1.14
|
= 1
|
Sent by a device when the value of the vlanTrunkPortDynamicStatus object has been changed.
|
Vlan trunk port dynamic status changed to trunking
|
not trunking
|
1.3.6.1.4.1.9.9.46.2.0.7
|
1.3.6.1.4.1.9.9.46.1.6.1.1.14
|
2
|
Sent by a device when the value of vlanTrunkPortDynamicStatus object has been changed.
|
Vlan trunk port dynamic status changed to not trunking
|
cps-Secure-MacAddr-Violation-Trap
|
1.3.6.1.4.1.9.9.315.0.0.1
|
NA
|
NA
|
The address violation notification is generated when port security address violation is detected on a secure non-trunk, access interface (that carries a single VLAN) and the cpsIfViolationAction is set to 'dropNotify'.
|
cps Secure MacAddr Violation Trap
|
cps-IfVlan-Secure-MacAddr-Violation-Trap
|
1.3.6.1.4.1.9.9.315.0.0.3
|
NA
|
NA
|
The address violation notification is generated when port security address violation is detected on a multi-VLAN interface and the cpsIfViolationAction is set to 'dropNotify'.
|
cps IfVlan Secure MacAddr Violation Trap
|
clc VlanMacLimit Notif
|
1.3.6.1.4.1.9.9.313.0.1
|
NA
|
NA
|
Notification is sent when the number of MAC addresses (the value of clcFdbVlanMacUsage) has crossed the configured limit of MAC addresses (clcVlanMaxMacLimit), either rising above or falling below it.
|
cisco L2 Control VlanMacLimit Notif Trap
|
clc VlanMacLimit High Notif
|
1.3.6.1.4.1.9.9.313.0.2
|
NA
|
NA
|
Notification is sent when the number of MAC addresses (the value of clcFdbVlanMacUsage) has crossed the configured higher threshold limit of MAC addresses (clcVlanMacLimitHigh), either rising above or falling below it.
|
cisco L2 Control VlanMacLimit High Notif Trap
|
clc IfMacLimit Low Notif
|
1.3.6.1.4.1.9.9.313.0.3
|
NA
|
NA
|
Notification is sent when the number of MAC addresses (the value of clcFdbIfMacUsage) has crossed the configured lower threshold limit of MAC addresses (clcIfMacLimitLow), either rising above or falling below it.
|
cisco L2 Control IfMacLimit Low Notif Trap
|
clc IfMacLimit High Notif
|
1.3.6.1.4.1.9.9.313.0.4
|
NA
|
NA
|
Notification is sent when the number of MAC addresses (the value of clcFdbIfMacUsage) has crossed the configured higher threshold limit of MAC addresses (clcIfMacLimitHigh), either rising above or falling below it.
|
cisco L2 Control IfMacLimit High Notif Trap
|
clc IfVlanMacLimit Low Notif
|
1.3.6.1.4.1.9.9.313.0.5
|
NA
|
NA
|
Notification is sent when the number of MAC addresses (the value of clcFdbIfVlanMacUsage) has crossed the configured lower threshold limit of MAC addresses (clcIfVlanMacLimitLow), either rising above or falling below it.
|
cisco L2 Control IfVlanMacLimit Low Notif Trap
|
clc IfVlanMacLimit High Notif
|
1.3.6.1.4.1.9.9.313.0.6
|
NA
|
NA
|
Notification is sent when the number of MAC addresses (the value of clcFdbIfVlanMacUsage) has crossed the configured higher threshold limit of MAC addresses (clcIfVlanMacLimitHigh), either rising above or falling below it.
|
cisco L2 Control IfVlanMacLimit High Notif Trap
|
