Table Of Contents

Physical Equipment

Inventory and Information Model Objects (IMOs)

Chassis

Shelf

Module

Power Supply

Port Connector

Service Alarms

Physical Equipment

---

This chapter describes the level of support that Cisco ANA provides for physical equipment, as follows:

•Inventory and Information Model Objects (IMOs)

•Service Alarms

Inventory and Information Model Objects (IMOs)

This section includes the following tables:

•Chassis (IChassis)

•Shelf (IShelf)

•Module/Board (IModule)

•Power Supply (IPowerSuply)

•Port Connector (IPortConnector)

Chassis

The following Chassis object describes a chassis equipment holder, which is bound by its Contained Equipment Holders attribute to other equipment holders such as shelves and slots.

Table 19-1 Chassis (IChassis)

Attribute Name	Attribute Description	Scheme	Polling Interval
Description	Chassis description	Any	Configuration
Equipment Holder Type	Equipment holder type (Chassis)	Any	Configuration
Contained Equipment Holders	Contained equipment holders	Any	Configuration
Contained Equipments	Contained equipment	Any	Configuration

Shelf

The following Shelf object describes a shelf equipment holder, which is bound by its Contained Equipment Holders and Contained Equipments attributes to other equipment holders and equipments objects it contains respectively.

Table 19-2 Shelf (IShelf)

Attribute Name	Attribute Description	Scheme	Polling Interval
Description	Chassis description	Any	Configuration
Status	Shelf status	Any	Configuration
Equipment Holder Type	Equipment holder type (Shelf)	Any	Configuration
Contained Equipment Holders	Contained equipment holders	Any	Configuration
Contained Equipments	Contained equipment	Any	Configuration

Module

The following Module object describes a module/board equipment, which is bound by its Contained Equipment Holders and supported Physical Termination Points attributes to other equipment holders (sub slots) and supported physical Termination Points (Port Connectors) objects it contains respectively.

Table 19-3 Module/Board (IModule)

Attribute Name	Attribute Description	Scheme	Polling Interval
Module Name	Module name	Any	Configuration
Module Description	Module description	Any	Configuration
Software Version	Software version	Any	Configuration
Operational Status	Operational status (Unknown, OK, Warning, Minor, Major, Critical, UnManaged, Enabled, Disabled, Information, Cleaning, Standby)	Any	Configuration
Hardware Type and Version	Hardware type and version	Any	Configuration
Management IP Address	Management IP address	Any	Configuration
Redundant Equipment	Redundant equipment number	Any	Configuration
Configured Redundancy	Configured redundancy (Null, Working, Protecting, None)	Any	Configuration
Redundancy Status	Redundancy status (Null, Active, Standby, None)	Any	Configuration
Operational Status Last Change	Date of last operational status change	Any	Configuration
Contained Equipment Holders	Contained equipment holders	Any	Configuration
Supported Physical Termination Points	Supported physical termination points	Any	Configuration

Power Supply

The following Power Supply object describes a power supply equipment, which is bound by its Contained Equipment Holders attributes to other equipment holders objects that it contains.

Table 19-4 Power Supply (IPowerSuply)

Attribute Name	Attribute Description	Scheme	Polling Interval
Operational Status	Operational status (Unknown, OK, Warning, Minor, Major, Critical, UnManaged, Enabled, Disabled, Information, Cleaning, Standby)	Any	Status
Hardware Type and Version	Hardware type and version	Any	Configuration
Management IP Address	Management IP address	Any	Configuration
Redundant Equipment	Redundant equipment number	Any	Configuration
Configured Redundancy	Configured redundancy (Null, Working, Protecting, None)	Any	Configuration
Redundancy Status	Redundancy status (Null, Active, Standby, None)	Any	Configuration
Operational Status Last Change	Date of last operational status change	Any	Configuration
Contained Equipment Holders	Contained equipment holders	Any	Configuration

Port Connector

The following Port Connector object describes a port connector physical termination point, which is being accessed by the Module containing it.

Table 19-5 Port Connector (IPortConnector)

Attribute Name	Attribute Description	Scheme	Polling Interval
Location	Port connector location	Any	Configuration
Alias	Port alias	Any	Configuration
Type	Port connector type (Unknown, BNC, RJ11, RJ45, Fiber Optic, RJ48, Fiber Optic FC, Fiber Optic SC, Fiber Optic ST, Fiber Optic LC, Internal, Backplane, Fiber Optics MT RJ, DB 15 Pin, SMB, DB 60 Pin, DB 50 Pin, 34-pin Winchester, Generic, DB 9 Pin)	Any	Configuration
Sub Ports	Sub connection termination points (currently being used only for Lucent SONET/ SDH equipment)	Any	Configuration
Supporting Equipment	Supporting equipment in which this port connector resides in	Any	Configuration
Contained Connection Termination Points	Bound Connection Termination Points	Any	Configuration

Service Alarms

The following alarms are supported for this technology:

•Card Out/Card In

•Card Down/Card Up

---

Note For a detailed description of these alarms and for information about correlation see the Cisco Active Network Abstraction Fault Management User Guide.

---