Table Of Contents

Common (Shared by Several)

Inventory and Information Model Objects (IMOs)

Physical Layer

Bridging Entity

Bridging Entry

VC Multiplexer

VC Encapsulation

Virtual Connection Switching Entity

Virtual Cross Connection

Forwarding Component Container

Traffic Descriptor Container

Tunnel Container

Network Topology

Service Alarms

Common (Shared by Several)

---

This chapter describes the level of support that Cisco ANA provides for the common components, as follows:

•Inventory and Information Model Objects (IMOs)

•Network Topology

•Service Alarms

Inventory and Information Model Objects (IMOs)

This section includes the following tables:

•Physical Layer (IPhysicalLayer)

•Bridging Entity (IBridge)

•Bridging Entry (IBridgeEntry)

•VC Multiplexer (EncapMux)

•VC Encapsulation (IVcBasedEncapsulation)

•VC Switching Entity (IVcSwitchingEntity)

•Virtual Cross Connection (IVcCrossConnect)

•Forwarding Component Container (IFWComponentContainer)

•Traffic Descriptor Container (ITrafficDescriptorContainer)

•Tunnel Container (ITunnelContainer)

Physical Layer

The following Physical Layer object, is bound by its Containing Termination Points attribute to a Port Connector object, and is accessed by the Data Link layer bound by its Contained Connection Termination Points attribute.

The Polling Interval (PI) of the Thresholds' attributes is marked as Not Applicable (N/A), as they do not originate from the modeled Network Element (NE), but rather from the Thresholds Crossing Alarms (TCA) system of the Virtual Network Element (VNE).

---

Note The following attributes are configured in the registry and not retrieved from the device.

---

Table 19-1 Physical Layer (IPhysicalLayer) 

Attribute Name	Attribute Description	Scheme	Polling Interval
Media Type	Physical media type (Null, Thin Coax, Thick Coax, Fiber Optic, Multi Mode Fiber Optic, Single Mode Fiber Optic, Short Single Mode Fiber Optic, Long Single Mode Fiber Optic, UTP, STP, FTP, EIA/TIA-232, EIA/TIA-449, V.35, X.21, EIA/TIA-530, EIA/TIA-530A, Generic Serial, EIA/TIA-612/613, Other)	Any	Configuration
Clocking Source	Clocking source (Unknown, Other, Network, Internal, Loop Timed, External, None, Line, Back Plane, Adaptive Timing)	Any	Configuration
Maximum Speed	Maximum supported speed with units specification	Any	System
Is Internal Port	Indicate an internal port, such as between module and backplane (True, False)	Any	Configuration
Maximum and Minimum Discarded Thresholds	Maximum and minimum discarded input bandwidth thresholds	Any	N/A
Discarded Bandwidth	Current discarded input bandwidth	Any	Configuration
Maximum and Minimum Dropped Thresholds	Maximum and minimum dropped output bandwidth thresholds	Any	N/A
Dropped Bandwidth	Current dropped output bandwidth	Any	Configuration
Maximum and Minimum Input Thresholds	Maximum and minimum utilized input bandwidth thresholds	Any	N/A
Input Bandwidth	Current utilized input bandwidth	Any	Configuration
Maximum and Minimum Output Thresholds	Maximum and minimum utilized output bandwidth thresholds	Any	N/A
Output Bandwidth	Current utilized output bandwidth	Any	Configuration
Discarded and Received Input Data Counters	Discarded and received input octets and packets counters	Any	Topology L1
Dropped and Forward Output Data Counters	Dropped and forward output octets and packets counters	Any	Topology L1
Administrative Status	Administrative status (Unknown, Up, Down, Testing)	Any	Status
Operational Status	Operational status (Unknown, Up, Down, Testing, Dormant, Not Present)	Any	Status
Operational Status Last Change	Date of last operational status change	Any	Configuration
IANA Type	IANA type of the sub/layer	N/A	N/A
Containing Termination Points	Underlying termination points (connection or physical)	Any	N/A
Contained Connection Termination Points	Bound Connection Termination Points	Any	N/A

Bridging Entity

The following Bridging Entity object describes the IEEE 802™ based protocols independent forwarding component of an IEEE 802™ Bridge/Switch, which is bound by its Logical Sons attribute to all the Data Link layers such as Ethernet, Token Ring and future Wireless LAN and MAN interface objects, which IEEE 802™ based Data Link frames are being bridged or switched between, by this Bridging Entity.

Table 19-2 Bridging Entity (IBridge) 

Attribute Name	Attribute Description	Scheme	Polling Interval
Bridge Table	Array of Bridging Entries	Any	Configuration
Type	Bridge type (Null, Automatic, Regular, Bridge Route)	Any	Configuration
MAC Address	Bridge internal MAC address used either for running Spanning Tree Protocol (STP) or for bridge's network management	Any	Configuration
IP Interface	OID of the IP Interface used mainly for routing traffic from that bridge	Any	Configuration
Name	Bridging entity name	Any	Configuration
Logical Sons	Array of all IEEE 802™ based data link interfaces (Ethernet Interface, Token Ring Interface ..), which IEEE 802™ based data link frames are being bridged/switched between, by this Bridging Entity	Any	Configuration

Bridging Entry

The following Bridging Entry object describes a bridging domain wide bridge table's entry of a Bridging Entity.

Table 19-3 Bridging Entry (IBridgeEntry)

Attribute Name	Attribute Description	Scheme	Polling Interval
Destination MAC Address	Destination station MAC address	Any	Configuration
Outgoing Interface	Outgoing underlying interface (Cisco's Ethernet Channels, Ethernet Interfaces, Virtual LAN Interfaces or Virtual LAN Multiplexers)	Any	Configuration

VC Multiplexer

The following VC Multiplexer object is bounded by its Containing Termination Points attribute to either an ATM Interface or a Frame Relay Interface object, and is primarily accessed by the Data Link layer VC Encapsulations bound by its Contained Connection Termination Points attribute.

Table 19-4 VC Multiplexer (EncapMux)

Attribute Name	Attribute Description	Scheme	Polling Interval
Virtual Connection Count	Bounded virtual connection count	Any	Configuration
IANA Type	IANA type of the sub/layer	N/A	N/A
Containing Termination Points	Underlying termination points (ATM Interface or Frame Relay Interface)	Any	N/A
Contained Connection Termination Points	Bound Connection Termination Points (VC Encapsulations)	Any	N/A

VC Encapsulation

The following Data Link layer VC Encapsulation object, is bound by its Containing Termination Points attribute to an ATM or Frame Relay VC Multiplexer object, and is primarily accessed by a network layer such as an IP Interface as well as a Data Link layer such as Ethernet Interface and Point To Point Protocol Encapsulation bound by its Contained Connection Termination Points attribute.

Table 19-5 VC Encapsulation (IVcBasedEncapsulation)

Attribute Name	Attribute Description	Scheme	Polling Interval
Virtual Connection	Virtual connection (ATM Virtual Connection or Frame Relay Virtual Connection)	Any	Configuration
Binding Information	Binding information (User Name, ...)	Any	Configuration
Binding Status	Binding status (Not Bound, Bound)	Any	Configuration
IANA Type	IANA type of the sub/layer	N/A	N/A
Containing Termination Points	Underlying termination points (connection or physical)	Any	N/A
Contained Connection Termination Points	Bound Connection Termination Points	Any	N/A

Virtual Connection Switching Entity

The following Virtual Connection Switching Entity object describes the standard forwarding component of an ATM or Frame Relay Switch, which is bound by its Logical Sons attribute to all the Data Link layers such as ATM Interface or Frame Relay Interface objects, which cells or frames respectively are being switched between, by this Virtual Connection Switching Entity.

Table 19-6 VC Switching Entity (IVcSwitchingEntity)

Attribute Name	Attribute Description	Scheme	Polling Interval
Cross Connect Table	Array of Virtual Cross Connections	Any	Configuration
Logical Sons	Array of all ATM Interfaces or Frame Relay Interfaces, which cells or frames respectively are being switched between, by this Virtual Connection Switching Entity	Any	N/A

Virtual Cross Connection

The following Virtual Cross Connection object describes either a Virtual Connection Switching Entity wide or an ATM Interface specific Cross Connect table's entry.

Table 19-7 Virtual Cross Connection (IVcCrossConnect)

Attribute Name	Attribute Description	Scheme	Polling Interval
Ingress and Egress Virtual Connection	Ingress and egress virtual connections (ATM Virtual Connection or Frame Relay Virtual Connection)	Any	Configuration
Ingress and Egress Port	Ingress and egress ports (Port Connectors)	Any	Configuration

Forwarding Component Container

The following Forwarding Component Container object aggregates a single type Forwarding Components, such as Routing Entity, Bridging Entity and Virtual Connection Switching Entity.

Table 19-8 Forwarding Component Container (IFWComponentContainer)

Attribute Name	Attribute Description	Scheme	Polling Interval
Forwarding Components	Array of a single type forwarding components	Any	Configuration
Type	Forwarding component (Null, Routing Entities, Bridges, VRFs, LSEs, VC Switching Entities, L2TP Peers, MPBGPs, IMA Groups)	Any	Configuration

Traffic Descriptor Container

The following Traffic Descriptor Container object, which basically is a container of any table's entries, aggregates a single type Traffic Descriptors such as OSPF Entry.

Table 19-9 Traffic Descriptor Container (ITrafficDescriptorContainer)

Attribute Name	Attribute Description	Scheme	Polling Interval
Traffic Descriptors	Array of a single type traffic descriptors	Any	Configuration
Type	Descriptor type (Null, ATM Traffic Profiles, ADSL Traffic Descriptors, SDSL Traffic Descriptors, IDSL Traffic Descriptors, SHDSL Traffic Descriptors, MPLS Properties, CAC Profiles, ATM Access Profiles, OSPF Networks, BGP Neighbor, Access Lists, Tunnel Traffic Descriptors, QoS Policies, QoS Classes, IS-IS Database, QoS WRED, ATM Traffic Shaping Profile, Frame Relay Traffic Profiles, Rate Limit, Filter, Policer, IP Pools, ISAKMP Policies, IPsec Maps, Process List, Installed Software, L2TP Peer Group, L2TP Domain Group, QoS Object Table, QoS Class Map, QoS Policy Map, QoS Match Statments Table, QoS Queueing Config Table, QoS Service Policy Table, ADSL2 Traffic Descriptors, ADSL2 Spectrum Descriptors)	Any	Configuration

Tunnel Container

The following Tunnel Container object aggregates single type tunnel interfaces, which are either MPLS TE Tunnel Interfaces or PTP Layer 2 MPLS Tunnel Interfaces.

Table 19-10 Tunnel Container (ITunnelContainer)

Attribute Name	Attribute Description	Scheme	Polling Interval
Tunnel Edges	Array of either PTP Layer 2 MPLS Tunnel Interfaces or MPLS TE Tunnel Interfaces	Any	Configuration

Network Topology

The Cisco Discovery Protocol (CDP), although a proprietary one, plays a major role in discovery of all Cisco's network equipment. Hence it is used as part of the physical topology discovery of Cisco's equipment by searching for the existence of local CDP neighbors signature, gathered from the physical layer, in any remote side's port of the same type.

Service Alarms

The following alarms are supported for this technology:

•Cloud Problem

•Discard Input Packets/Normal Discard Input Packets

•Dropped Output Packets/Normal Dropped Output Packets

•Link Down/Link Up

•Port Down/Port Up

•Receive Utilization/Receive Utilization Normal

•Transmit Utilization/Transmit Utilization Normal

---

Note For a detailed description of these alarms and for information about correlation see the Cisco Active Network Abstraction Fault Management User Guide.

---