Table Of Contents

Physical Equipment

Inventory and Information Model Objects (IMOs)

Chassis

Shelf

Module

Power Supply

Port Connector

Service Alarms

Physical Equipment

---

This chapter describes the level of support that Cisco ANA provides for physical equipment, as follows:

•Inventory and Information Model Objects (IMOs)

•Service Alarms

Inventory and Information Model Objects (IMOs)

This section describes the following IMOs:

•Chassis (IChassis)

•Shelf (IShelf)

•Module/Board (IModule)

•Power Supply (IPowerSuply)

•Port Connector (IPortConnector)

Chassis

The Chassis object represents an equipment chassis. Its Contained Equipment Holders attribute binds it to other equipment holder objects, such as a Shelf.

Table 19-1 Chassis (IChassis)

Attribute Name	Attribute Description	Scheme	Polling Interval
Description	Chassis description	Any	Configuration
Equipment Holder Type	Equipment holder type (Chassis)	Any	Configuration
Contained Equipment Holders	Contained equipment holders	Any	Configuration
Contained Equipments	Contained equipment	Any	Configuration

Shelf

The Shelf object represents a shelf. Its Contained Equipment Holders and Contained Equipments attributes bind it to other equipment holders and equipments objects it contains.

Table 19-2 Shelf (IShelf)

Attribute Name	Attribute Description	Scheme	Polling Interval
Description	Chassis description	Any	Configuration
Status	Shelf status	Any	Configuration
Equipment Holder Type	Equipment holder type (Shelf)	Any	Configuration
Contained Equipment Holders	Contained equipment holders	Any	Configuration
Contained Equipments	Contained equipment	Any	Configuration

Module

The following Module object represents a module or board. Its Contained Equipment Holders and supported Physical Termination Points attributes bind it to other equipment holders (sub slots) and supported physical Termination Points (Port Connectors) objects it may contain.

Table 19-3 Module/Board (IModule)

Attribute Name	Attribute Description	Scheme	Polling Interval
Module Name	Module name	Any	Configuration
Module Description	Module description	Any	Configuration
Software Version	Software version	Any	Configuration
Operational Status	Operational status (Unknown, OK, Warning, Minor, Major, Critical, UnManaged, Enabled, Disabled, Information, Cleaning, Standby)	Any	Configuration
Hardware Type and Version	Hardware type and version	Any	Configuration
Management IP Address	Management IP address	Any	Configuration
Redundant Equipment	Redundant equipment number	Any	Configuration
Configured Redundancy	Configured redundancy (Null, Working, Protecting, None)	Any	Configuration
Redundancy Status	Redundancy status (Null, Active, Standby, None)	Any	Configuration
Operational Status Last Change	Date of last operational status change	Any	Configuration
Contained Equipment Holders	Contained equipment holders	Any	Configuration
Supported Physical Termination Points	Supported physical termination points	Any	Configuration

Power Supply

The Power Supply object represents a power supply. Its Contained Equipment Holders attribute bind it to other equipment holder objects it may contain.

Table 19-4 Power Supply (IPowerSuply)

Attribute Name	Attribute Description	Scheme	Polling Interval
Operational Status	Operational status (Unknown, OK, Warning, Minor, Major, Critical, UnManaged, Enabled, Disabled, Information, Cleaning, Standby)	Any	Status
Hardware Type and Version	Hardware type and version	Any	Configuration
Management IP Address	Management IP address	Any	Configuration
Redundant Equipment	Redundant equipment number	Any	Configuration
Configured Redundancy	Configured redundancy (Null, Working, Protecting, None)	Any	Configuration
Redundancy Status	Redundancy status (Null, Active, Standby, None)	Any	Configuration
Operational Status Last Change	Date of last operational status change	Any	Configuration
Contained Equipment Holders	Contained equipment holders	Any	Configuration

Port Connector

The Port Connector object represents a port connector physical termination point. It is accessed by the Module containing it.

Table 19-5 Port Connector (IPortConnector)

Attribute Name	Attribute Description	Scheme	Polling Interval
Location	Port connector location	Any	Configuration
Alias	Port alias	Any	Configuration
Type	Port connector type (Unknown, BNC, RJ11, RJ45, Fiber Optic, RJ48, Fiber Optic FC, Fiber Optic SC, Fiber Optic ST, Fiber Optic LC, Internal, Backplane, Fiber Optics MT RJ, DB 15 Pin, SMB, DB 60 Pin, DB 50 Pin, 34-pin Winchester, Generic, DB 9 Pin)	Any	Configuration
Sub Ports	Sub connection termination points (currently being used only for Lucent SONET/ SDH equipment)	Any	Configuration
Supporting Equipment	Supporting equipment in which this port connector resides in	Any	Configuration
Contained Connection Termination Points	Bound Connection Termination Points	Any	Configuration

Service Alarms

The following alarms are supported for this technology:

•Card Out/Card In

•Card Down/Card Up

For detailed information about alarms and correlation, see the Cisco Active Network Abstraction 3.6.5 User Guide.