-
Cisco IOS XR System Error Message Reference Guide, Release 4.1
-
Preface
-
Overview
-
Access Control List (ACL) Messages
-
Application Infrastructure Messages
-
Diagnostic Messages
-
Fabric Messages
-
Forwarding Messages
-
High Availability (HA) Messages
-
Infrastructure Messages
-
Installation Messages
-
Internet Protocol Messages
-
Layer 1 Messages
-
Layer 2 Messages
-
Layer 3 Messages
-
License Messages
-
Media Messages
-
Manageability (MGBL) Messages
-
Operating System Messages
-
Packet Infrastructure Messages
-
Platform Messages
-
Policy Manager Messages
-
Quality of Service Messages
-
Routing Messages
-
Security Messages
-
Service Messages
-
Simple Network Management Protocol (SNMP) Messages
-
Subscriber Messages
-
System Database Messages
-
Feedback
Table Of Contents
IP_STATIC_BFD_SESSMGR Messages
IPV4_MCAST_NETIO_DEBUG Messages
POLICY_REPOSITORY_DYNREG Messages
POLICY_REPOSITORY_EDM Messages
Routing Messages
This section contains all routing related System Error Messages, such as MPLS, OSPF, BGP, Multicast, MRIB, RIB, and so forth.
AIB_CLIENT Messages
Error Message%ROUTING-AIB_CLIENT-3-EXTRA_UNLOCK Adjacency consumer (Job ID: [unsigned int]) attempted extra unlock on adjacency [hex] (interface handle:[hex],protocol:[unsigned int])
Explanation An unexpected unlock is attempted by adjacency consumer.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
AIB Messages
Error Message%ROUTING-AIB-1-EVENTBLOCK event_block returned early : [chars] (errno equals [dec])
Explanation An unexpected or erroneous return while waiting for events.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-3-EXTRA_UNLOCK Adjacency consumer (Job ID: [unsigned int]) attempted extra unlock on adjacency [hex] (interface handle:[hex],protocol:[unsigned int])
Explanation An unexpected unlock is attempted by adjacency consumer.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-IDB_NOT_FOUND Cannot create the IDB, ifh:[hex]
Explanation There are no resources to create the IDB.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-INDEX_REG_FAIL AIB process cannot register with the platform specific DLL (return equals [dec])
Explanation The AIB process cannot register with the platform specific adjacency index DLL. The adjacency database will not be created.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-INDEX_VERSION_FAIL AIB process has detected a version mismatch between itself and the platform DLL (DLL version is [dec], AIB expected [dec])
Explanation The AIB process has detected that the platform specific adjacency indexing DLL has reported a version number that does not match the AIB process version number. Due to this inconsistency, the AIB cannot continue and the system will not be able to process any adjacency information.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-LEN_MISMATCH_CLDATA The client data has changed in length. Old len:[unsigned int], New len:[unsigned int]
Explanation An unexpected change in length of client data occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-LTRACE_ERROR Failed to open trace file: [chars]
Explanation The AIB process was unable to open the trace buffer for automatic tracing (show trace adjacency may not work).
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-RADIXINIT_FAIL AIB failed to initialize the interface db radix tree ([chars])
Explanation Initialization of the radix tree could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-AIB-4-SHM_FAIL AIB Shared memory error: [chars] [chars]
Explanation The AIB process received an error while trying to initialize the shared memory.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AIB-4-SYSTEM_FAIL [chars] [chars] (errno equals [dec])
Explanation There was a system call failure resulting in a failure to provide a system service as indicated in the message text.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
AUTORP_CRP Messages
Error Message%ROUTING-AUTORP_CRP-3-BAG_RELATED_ERROR Bag related error: [chars]
Explanation The Candidate RP had trouble with Bags.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-EDM_ACCESS_ERROR Sysdb EDM related error: [chars], [chars]
Explanation The Candidate RP had trouble accessing SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-EVENT_CONN_MGR_ERROR Event connection manager error : [chars], [chars]
Explanation Failure to open connection to Connection Manager occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-EVENT_MGR_CREATE_FAILED Failed to create an event manager
Explanation A problem occurred when a call to event_manager_create() was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-GEN_ERROR Error : [chars] failed - [chars]
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-IM_RELATED_ERROR A call to [chars] returned [chars]
Explanation A problem occurred when a call to IM was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-INIT_FAILED Initialization failed : [chars]
Explanation autorp_candidate_rp failed to initialize successfully.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-IPARM_RELATED_FAILURE A call to [chars] returned [chars]
Explanation A problem occurred when a call to one of the IPARM APIs was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-MALLOC_FAILED malloc() failed : failed to allocate memory to receive messages
Explanation A call to malloc() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-SOCKET_ERROR Socket Error : [chars] : [chars]
Explanation A socket error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-SYSDB_ACCESS_ERROR Sysdb related error: [chars], [chars]
Explanation The Candidate RP had trouble accessing SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-SYSDB_REGISTRATION_FAILED Sysdb registration error: [chars]
Explanation The Candidate RP had trouble registering as a notifier with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-TIMER_ERROR Timer Error : [chars]
Explanation A timer error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_CRP-3-TUPLE_ERROR Tuple operation error : [chars]
Explanation Tuple operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
AUTORP_MAP Messages
Error Message%ROUTING-AUTORP_MAP-3-BAG_RELATED_ERROR Bag related error: [chars]
Explanation The Mapping Agent had trouble with Bags.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-DEBUG_ERROR Debug error : [chars]
Explanation A debug error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-EDM_ACCESS_ERROR Sysdb EDM related error: [chars], [chars]
Explanation The Mapping Agent had trouble accessing SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-EVENT_CONN_MGR_ERROR Event connection manager error: [chars], [chars]
Explanation Failure to open connection to Connection Manager occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-EVENT_MGR_CREATE_FAILED A call to event_manager_create() failed
Explanation A problem occurred while calling the event_manager_create() API.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-IM_RELATED_ERROR The function [chars] returned error : [chars]
Explanation Failure of some IM related operation occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-INIT_FAILED Initialization failed : [chars]
Explanation autorp_mapping_agent failed to initialize successfully.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-INIT_FAILED_ERR '[chars]' initialization failed : [chars]
Explanation autorp_mapping_agent failed to initialize successfully.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-IPARM_RELATED_FAILURE A call to [chars] returned [chars]
Explanation A problem occurred when a call to one of the IPARM APIs was made.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-MALLOC_FAILED malloc() failed : failed to allocate memory to receive messages
Explanation A call to malloc() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-OOR_LIMIT Cache maximum reached: [dec], new group range not added
Explanation An OOR error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-RTREE_ERROR RTree error : [chars]
Explanation A timer error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-SOCKET_ERROR Socket Error : [chars] : [chars]
Explanation A socket error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-SYSDB_ACCESS_ERROR Sysdb related error: [chars], [chars]
Explanation The Mapping Agent had trouble accessing SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-SYSDB_REGISTRATION_FAILED Sysdb registration error: [chars]
Explanation The Mapping Agent had trouble registering as a notifier/edm with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-TIMER_ERROR Timer Error : [chars]
Explanation A timer error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-AUTORP_MAP-3-TUPLE_ERROR Tuple operation error : [chars]
Explanation Tuple operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
BGP_VRF Messages
Error Message%ROUTING-BGP_VRF-3-DUPLICATE_ID Failed to store [chars] ID [hex] for VRF [chars].
Explanation A ID has been received from RSI that duplicates an existing VRF or table ID. As a result, the new ID has been ignored, and subsequent operation for that VRF will be incorrect.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP_VRF-3-INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP VRF module. The BPM process will be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP_VRF-3-NOTIFY Failed to apply configuration change for: [chars] ([chars]).
Explanation A notification of a configuration change could not be applied, leaving the internal data structures inconsistent with the configuration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP_VRF-3-RD_APPLY Failed to apply RD configuration change for [chars]. System may now be in an inconsistent state.
Explanation The RD value for the VRF failed to be set, leaving the internal data structures inconsistent with the configuration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP_VRF-3-RD_PUBLISH Failed to publish RD configuration: [chars]. System may now be in an inconsistent state.
Explanation The RD value for a VRF or set of VRFs failed to be published.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
BGP Messages
Error Message%ROUTING-BGP-2-ADDROUTE Failed to add net [chars] to the BGP table
Explanation An error occurred while trying to insert a net to the BGP table database.
Recommended Action This error occurs when you are not able to add a net to the BGP table' 'database. In some cases the nbr that had sent that net would reset, and the issue would recover. In other cases you might see an accompanying low memory message. Please check to make sure you have enough free/available memory on the router.
Error Message%ROUTING-BGP-2-ERR_EVM_EVENT_BLOCK Error in event loop for [chars] thread: [chars]
Explanation An error occurred in the event loop. In most of the cases, it will recover.
Recommended Action Please provide output from the following commands:
–
show version
–
–
–
–
–
–
Error Message%ROUTING-BGP-2-ERR_FILE_ATTACH Failed to do [chars] event file attach - [chars]
Explanation An error occurred when bgp try to do event file attach.
Recommended Action In most cases the problem will recover by resetting the nbr for which file attach is failing. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-ERR_MEM_ALLOC Failed to allocate memory for [chars]
Explanation The requested operation could not be accomplished because of a low memory condition. BGP may not operate correctly until the process is restarted.
Recommended Action Reduce other system activity to ease memory demands, then restart the process. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-BGP-2-ERR_THREAD_DEADLOCK Deadlock detected (thread [unsigned int]): holding: [chars]
Explanation BGP detected a lock being held when all locks should have been released.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-FATAL_WRAPPER Fatal error: A call to [chars] failed unexpectedly: [chars]
Explanation A function call failed unexpectedly. This is probably a system problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-2-NSR_RESTART_FAILED NSR has been unconfigured and configured too many times in a short period of time. Forcing a restart of standby bgp to restore NSR functionality.
Explanation Standby BGP restarts itself when NSR is disabled. If standby BGP attempts to restart itself too many times, then sysmgr will block any further restart attempt. If standby BGP does not restart, then NSR functionality might be affected when NSR is enabled the next time. Therefore, a restart is forced by a call to exit().
Recommended Action This message is informational only.
Error Message%ROUTING-BGP-2-TRIGGER_FO Triggering switch-over to keep NSR up, Failure reason: [chars]
Explanation If nsr switch-over knob is on, active bgp will trigger the switch over in case of tcp failure or bgp failure if nsr is ready and install is not in process.
Recommended Action This message is informational only. Analysis should be done if switch-over is not expected.
Error Message%ROUTING-BGP-3-AF_LIB_FILE_ERROR Failed to read Address Family data file: [chars] [chars]
Explanation File/Directory open operation failed, or the data in the file was corrupt.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-AF_LIB_FILE_WRONG_INFO Failed to read Address Family data file [chars]: [chars] on line [unsigned int]
Explanation The data in the Address Family data file was corrupt.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ALREADY_DONE Cannot [chars]%s: already done
Explanation An operation could not be performed because it had already been completed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ATTRKEY_BAD Failed to [chars] RIB due to an invalid attribute key number ([hex])
Explanation There is a problem with the attribute key generation routine.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ATTRKEY_CHKPT Failed to checkpoint attribute key
Explanation The chkpt library failed to checkpoint the attribute key number. Normal operation of BGP (standalone) or bRIB (distributed) is not impacted unless the process is restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ATTRKEY_OVERFLOW Failed to generate a new attribute key for the incoming UPDATE
Explanation This is an extremely rare case where the attribute key overflow protection mechanism fails.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BAD_REFCNT Bad reference count value ([unsigned int]) for [chars] ([pointer])
Explanation This indicates a internal data structure inconsistency.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_AS_INIT As-num is not set yet in bpm and can not apply other config
Explanation Do not attempt to publish anything until AS number is set.
Recommended Action This warning will show up for possible out of order sysdb notification.
Error Message%ROUTING-BGP-3-BPM_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP process manager. If this occurred during process startup or RP Switchover, then the process may be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_PROCESS_START Failed to start [chars] process (ID: [unsigned int]): [chars]
Explanation The BPM failed to start the process in the error message. As a result, the process will not be running.
Recommended Action Check that the process is not already running using the 'show process bgp location all' or 'show process brib location all' command as appropriate. If the process is not running, attempt to start it using the 'process restart' command. If other error messages are seen along with this one, or when attempting to manually start the process, please consult the documentation for those errors and attempt to rectify them. If problems persist, copy this error message and any others exactly as they appear on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_PROCESS_STOP Failed to stop [chars] process (ID: [unsigned int]): [chars]
Explanation An error occurred when trying to stop the process specified in the error message. As a result, the process may still be running, which could adversely affect the operation of other processes.
Recommended Action Check whether the process is still running using the 'show process bgp location all' or 'show process brib location all' command as appropriate. If the process is running, kill it using the 'process kill' command. If problems persist, copy this error message and any subsequent ones exactly as they appear on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BPM_SWITCH_MODE Failed to switch to [chars] mode: [chars] ([chars])
Explanation An error occurred when switching between standalone and distributed mode.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BRIB_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP RIB. If this occurred during process startup or RP Switchover, then the process may be restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-BUF_TOO_SHORT A string buffer was too short during a string print operation (string [chars] truncated)
Explanation While trying to format a string, the buffer passed in was too short and the string was truncated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-COMM_DECODE_RDINFO [chars] [unsigned int] [unsigned int]
Explanation Standby BGP received invalid Route Distinguisher information from Active BGP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-CONFIG_DEL Notify delete of [chars] failed with warning: [chars], no further action necessary.
Explanation A speaker or the bRIB failed to process the removal of some configuration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-CONFIG_FALLOVER Apply for fast-external-fallover failed: [chars]
Explanation A speaker failed to process a configuration change for 'fast-external-fallover'.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-CONFIG_SET Notify for [chars] failed with error: [chars], system may now be in an inconsistent state.
Explanation A speaker or the bRIB failed to process a configuration change.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-CREATE_REGS Create Registration failed: intfhandle ([unsigned int]) for interface [chars]
Explanation Create and Delete Registration failed for the named interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-DEBUG_CONFIG Failed to apply debug configuration: [chars]
Explanation An error occurred while applying the debug configuration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-DELPATH Attempted to delete path from empty net [chars]
Explanation An attempt was made to delete a path from a net with a path count of 0.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-DLL_ERROR Failed to [chars] [chars] DLL: [chars]
Explanation An error occurred while trying to open or initialize a DLL. The process will be restarted if this error occurs during process startup.
Recommended Action If the process has been restarted and the problem recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-EDM_INIT_FAILED EDM server initialization failed: [chars]: [chars]
Explanation Initialization of the EDM server failed. The process will be restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ERR_ALM_API ALM/LSD API: [chars] - [chars] failed
Explanation An ALM/LSD API returned an error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ERR_ALM_ONE_LABEL Unable to allocate label: [chars] - net [chars] tableid [hex] request type [dec] fpi_err:[hex]
Explanation The ALM/LSD API was unable to allocate a requested label.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ERR_GENERAL [chars]
Explanation A non-fatal fault occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ERR_PATH_ELEM Error encountered during [chars] of path element of network [chars] for [chars] address-family. Error code is [dec] ([chars]).
Explanation There was an error associated with path element operation, most likely due to low memory conditions. BGP may not operate correctly until the process is restarted.
Recommended Action Reduce other system activity to ease memory demands, then restart the process. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-BGP-3-EXTCOMM Failed to create extended community: [chars]
Explanation The import table list associated with an extended community set could not be created. This can occur if there is insufficient memory to allocate the import table list, or the number of importing tables exceeds the hard coded limit on the number of tables that a route may be imported into.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-EXTCOMM_ADD Failed to add one or more [chars] extended community for table [chars] prefix [chars]
Explanation While attaching extended communities to the path attribute you reached the maximum extended community limit and as a result you failed to add one or more extended community to the path attribute.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-GWCTX_CREATE Failed to [chars] for Gateway Context (VRF [chars], Gateway address-family [chars])
Explanation A software error has occurred while trying to initialize gateway context database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-HA_INIT Initialization failed ([chars]%s)
Explanation High availability initialization failed. If this occurred during process startup or RP Switchover, then the process may be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IFACE_LOOKUP Interface lookup for [chars] Failed: [chars]
Explanation Interface manager failed to lookup nexthop interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IM_DMZLINK_BW Failed to register for DMZ link bandwidth change for neighbor [chars]: [chars]
Explanation BGP failed to register with interface manager for DMZ link bandwidth change notification for a given neighbor
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IMPORT_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the import thread. If this occurred during process startup, then the process may be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-INIT_GET_VALUE Failed to obtain [chars] during initialization: [chars]
Explanation An error occurred when retrieving a required value during initialization. As a result the BGP process can not initialize.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-INITSYNC_FAILED [chars]
Explanation There was problem during init sync.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-INITSYNC_PFX_MISMATCH [chars]
Explanation The number of prefixes synced by active does not match the expected count.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-INSUFMEM Failed to allocate memory for [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-BGP-3-INTERNAL_ERROR Internal error ([chars])
Explanation A non-fatal fault occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-INVAL_REDUNDANCY_ROLE Initialization failed ([chars]%s)
Explanation An invalid Redundancy Role was delivered to BGP. If this occurred during process startup or RP Switchover, then the process may be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IO_INIT Initialization failed: [chars] [chars] ([chars])
Explanation An error occurred while initializing the IO thread in speaker process. The process will be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-IO_INITSYNC_SESSION_FAILED [chars] - for session, retry
Explanation A problem occurred in TCP init sync.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-LABEL_INIT Initialization of BGP/LABEL failed ([chars]:[chars])
Explanation An error occurred while initializing the LABEL thread. This could be caused by failure to allocate resources or by errors when calling the MPLS label manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-LOCK_RECURSIVE Attempt to recursively lock net [pointer] (lock: [hex])
Explanation A software error has occurred while trying to lock a network entry in the BGP Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-MALFORM_UPDATE received a malformed UPDATE from [chars], attr code [dec], action [chars]
Explanation This message indicates that the UPDATE message contains one or more malformed attributes. Depending on the nature and severity of the error, one of the following actions has been taken: reset the session, or discard the attribute, or treat the UPDATE as withdraw.
Recommended Action The last malformed UPDATE is available in 'show bgp neighbor', and it should be decoded and analyzed.
Error Message%ROUTING-BGP-3-MAX_IMPORT No. of importing VRFs exceeds max ([unsigned int]), limited to [unsigned int] tables: (Err: [chars])
Explanation There is a hard coded limit on the number of tables that a route may be imported into. This limit has been exceeded, so the route may not be present in some of the importing tables. The limit is such that this message should not be seen under normal operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-MAX_VALUE_EXCEEDED The value of [chars] ([unsigned int]) exceeds the maximum value: [unsigned int]
Explanation The value of an internally computed variable has exceeded the maximum value.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-MIB_INIT BGP MIB init failed ([chars])
Explanation An error occurred while initializing the BGP MIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-NBR_NSR_DISABLED NSR disabled on neighbor [chars] due to [chars]
Explanation NSR has been disabled on the neighbor temporarily due to transport issues.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-NEGCOUNTER Negative path counter for peer [chars]
Explanation The counter value for accepted prefixes is wrong and less than zero.
Recommended Action The counter can be corrected by resetting the session. However, the only behavior affected by an incorrect counter is enforcement of the 'max-prefix' command.
Error Message%ROUTING-BGP-3-NH_LOCK_RECURSIVE Attempt to recursively lock nexthop [pointer] (lock: [hex], vrf: [chars], afi: [chars])
Explanation A software error has occurred while trying to lock a nexthop entry in the BGP nexthop Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-NH_UNLOCK_ERR Failed to unlock nexthop node [pointer] (nh '[chars]', lock [hex], vrf '[chars]', afi '[chars]', cnt [unsigned int], ln [unsigned int])
Explanation A software error has occurred while trying to unlock an entry in the BGP nexthop Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-NOMEM_RESET Failed to allocate memory for [chars], resetting neighbor
Explanation The requested operation could not be accomplished because of a low memory condition. One or more neighbor sessions have been reset to free some memory.
Recommended Action In the problem recurs, reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-BGP-3-NOMSGCHUNK Failed to allocate [unsigned int] bytes from the memory pool for message of type [unsigned int]
Explanation A request was made to allocate a message size for which there was no memory pool large enough. This may indicate a software error in the calculation of the requested size.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-NOPAK_CONN Failed to clean up packet manger connection [chars]
Explanation A connection to the packet manager could not be established.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ORA_INSTBUILD Failed to build [chars]: [chars] ([chars])
Explanation Internal error in the routing policy library occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ORA_ORABUILD Failed to build ORA[chars]: [chars] ([chars])
Explanation There was an internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in the routing policy library occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-OVERCOUNTER [chars] counter overflow
Explanation A counter with maximum value was incriminated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-PENDING_MSG_ERR [chars] pending [chars] msg [chars] the pending msg list
Explanation A problem occurred while adding/removing pending message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-QAD_FAILURE QAD failure - [chars]
Explanation BGP detected an error condition in QAD. String should contain more information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-QAD_SEND_ERR QAD send err [chars] - BGP will reinitialize NSR
Explanation An error occurred to send a message to the QAD queue. This triggers NSR resynchronization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-QAD_TIMEOUT QAD timeout - BGP will reinitialize NSR
Explanation A message is dropped in the QAD queue. This triggers NSR resynchronization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RD_CREATE Failed to [chars] for RD [chars], address-family [chars]
Explanation A software error has occurred while trying to initialize RD node inside BGP Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RD_LOCK_RECURSIVE Attempt to recursively lock rdinfo [pointer] (lock: [hex])
Explanation A software error has occurred while trying to lock a network entry in the BGP Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RD_UNLOCK_ERR Failed to unlock RD node [pointer] (lock: [hex])
Explanation A software error has occurred while trying to unlock an entry in the BGP RD Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-REDIST_FAIL Failed to register with the RIB for redistribution of [chars] [chars] [chars] routes: [chars]
Explanation A RIB client library call for redistribution of routes failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_CONN_FAIL Failed to open connection to the RIB for address family [unsigned int]: [chars]
Explanation The connection to the RIB could not be established and a retry timer could not be started.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_FAIL Failed to [chars] for [chars] while calling the RIB instance [unsigned int]: [chars]
Explanation A RIB library call failed unexpectedly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP RIB thread. The process will be restarted if this error occurs during process startup.
Recommended Action If the process has been restarted and the problem recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_INIT_FAIL Initialization to RIB failed for [chars]: [chars]
Explanation An error occurred while initializing the RIB for a new address family. This could be caused by failure to allocate resources or by errors when calling the Table Resource Manager or the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-RIB_RETRY_FAIL RIB route retry failure: [chars] for [chars]
Explanation Some routes were not successfully installed in the RIB. Consequently, an attempt was made to save these routes to retry later. However, an error was encountered during the save attempt.
Recommended Action Issue a 'clear route address family sub-address family' to cause BGP routes to be reinstalled in the RIB. If this does not work, issue a soft or hard reset to all peers.
Error Message%ROUTING-BGP-3-RIB_TABLE_FAIL Failed to [chars] for [chars], RIB table [hex]
Explanation An error was encountered during some operation for the specified address family and RIB table. This could be due either to a lack of resources or a software problem.
Recommended Action Issue a 'clear route address family sub-address family' to cause BGP routes to be reinstalled in the RIB. If this does not work, issue a soft or hard reset to all peers.
Error Message%ROUTING-BGP-3-SCAN_INIT Scanner library initialization failed ([chars]%s)
Explanation An error occurred while initializing the scanner library. The process will be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-SPKR_INIT Initialization failed ([chars]%s)
Explanation An error occurred while initializing the BGP speaker process. If this occurred during process startup or RP Switchover, then the process may be restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-TABLE_CREATE Failed to create table context for the vrf [chars] afi/safi [dec]/[dec]: [chars]
Explanation An error occurred when creating the table context for the shown vrf name, afi, safi. As a result table can't be activated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-TBLATTR_VERSION Unable to propagate table attribute versions for [chars] : [chars]
Explanation An internal error was encountered.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-TIMER_PARENT_CHANGE failed for neighbor [chars], [chars]
Explanation There was an error in IOS-XR managed timer library API.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-UNDERCOUNTER [chars] counter underflow
Explanation A counter with zero value was decremented.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-UNKNOWN_MEMSTATE BGP received a notification about an unknown memory state ([unsigned int])
Explanation BGP received a low memory notification from wdsysmon for an unknown memory state, i.e. not NORMAL, MINOR, SEVERE or CRITICAL. As a result, no action was taken.
Recommended Action Check the memory on the node, and if it is low, take manual action to release memory, e.g. by resetting some BGP neighbors (using the 'clear bgp' command).
Error Message%ROUTING-BGP-3-UNLOCK_ERR Failed to unlock net [pointer] (lock: [hex])
Explanation A software error has occurred while trying to unlock a network entry in the BGP Table database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-VRF_CREATE Failed to create VRF context for the vrf [chars] : [chars]
Explanation An error occurred when creating the vrf context for the shown vrf name. As a result VRF can't be enabled.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-3-VRF_DELETE VRF [chars] still has undeleted table afi/safi [dec]/[dec]. Table will be deleted.
Explanation An error occurred while deleting the VRF. An address-family table under the VRF is still not deleted. Ideally all the tables under the VRF should be deleted first before VRF is deleted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-ATTRKEY_INCONSISTENT BGP detected an inconsistency in attribute key generation. Will correct the problem by renumbering all attributes
Explanation The attribute key generation routine has gone beyond the checkpointed value. This is a rare condition to occur as the key generation algorithm is very simple.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-BFD_INVALID_NBR Attempt to register BFD session on invalid neighbor: [chars]
Explanation Internal error indicating that an attempt has been made to create a BFD session for a neighbor type that is not supported by BFD.
Recommended Action The BFD session for the neighbor in the log will not be created. If a BFD session for this neighbor is not required, no further action is needed. To re-attempt creation of a BFD session for this neighbor, remove and re-add the bfd fast-detect configuration for the neighbor.
Error Message%ROUTING-BGP-4-BPM_NEG_NBR BGP and sysdb are out of sync (neighbor configuration was present but no neighbors in BGP)
Explanation BGP and sysdb are out of sync (neighbor config present but no neighbor in bgp) and as a result, unconfiguring neighbor results in negative neighbor count in BGP
Recommended Action This message is informational only.
Error Message%ROUTING-BGP-4-CAP_4BYTEAS Capability 4-byte-as suppress misconfigured for neighbor [chars]
Explanation Possible misconfiguration with 'capability 4-byte-as suppress' occurred. This configuration can be inherited from either a neighbor-group or a session-group by a neighbor whose remote-as is a 4-byte as number. Suppress should be off for such neighbor.
Recommended Action Check the bgp configuration. Remove the 'capability 4-byte-as suppress' configuration or disable it to prevent getting inherited from the neighbor-group or a session-group
Error Message%ROUTING-BGP-4-DESTROY_CHUNK Chunk pool [chars] is no longer in use but cannot be destroyed
Explanation BGP has resized its bit fields, so the old bit field chunks should be destroyable. Nonetheless, BGP is unable to destroy the old chunk and, cannot release unwanted memory.
Recommended Action This error will not cause any erroneous behavior, hence no further action is needed to rectify the situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-ENCODE_NET_OVERRUN Encoding [chars] has overrun the msg buffer (written size [unsigned int], max size [unsigned int])
Explanation Encoding the net has overrun the msg buffer. It may corrupt some memory.
Recommended Action This warning indicates possible memory overrun.
Error Message%ROUTING-BGP-4-ERR_MALFORMED_ORF Ignored Received malformed entry message in [chars]
Explanation The ORF entry is encoded incorrectly.
Recommended Action None.
Error Message%ROUTING-BGP-4-INCONSISTENT Detected inconsistent config state: [chars]
Explanation The internal state representing the configuration was invalid, but has now been fixed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-INCONSISTENT_ASPATHMERGE received an UPDATE from [chars] with Inconsistent AS_PATH and AS4_PATH, action [chars]
Explanation This message indicates that the AS_PATH and AS4_PATH attributes in the UPDATE consist of segments that are inconsistent when doing a merge, discard the AS4_PATH in this case
Recommended Action A counter is available in 'show bgp neighbor', to log this event and displayed only when the count is greater than 0.
Error Message%ROUTING-BGP-4-L2VPN_DEL_ADD Trying to Readd L2VPN [chars] when previous instance is still in Deletion
Explanation BGP detected that an attempt was made to instantiate an L2VRF when the instance is in the process of being deleted. This will happen when the router-id is unconfigured, configured with another value and reconfigured with the first value all in very quick succession.
Recommended Action This message is informational only. At this point BGP and L2VPN will be out of sync. Need process restart to achieve sync.
Error Message%ROUTING-BGP-4-L2VPN_RD_LOCAL_AND_REMOTE RD 0x [pointer] is marked both local and remote
Explanation BGP detected that the RD is marked both local and remote This means that the local table_ctx points to this rdinfo but this rdinfo points to the shared tabel_ctx.
Recommended Action This message is informational only. At this point BGP and L2VPN will be out of sync. Need process restart to achieve sync.
Error Message%ROUTING-BGP-4-L2VPN_READD Trying to Readd L2VPN [chars] when previous instance is still there
Explanation BGP detected that an attempt was made to instantiate an L2VRF when the instance still exists. This will happen when the L2VPN module can issue two successive adds followed by delete whereas they meant to send add, delete and then add.
Recommended Action This message is informational only. At this point BGP and L2VPN will be out of sync. Need process restart to achieve sync.
Error Message%ROUTING-BGP-4-L2VPN_SIGNAL_MISMATCH Same RD Net [chars] or [chars] does not match VRF Signalling Type
Explanation BGP detected that the prefix was learned with a signalling type different from what is configured for the vrf. Do not allow both types of signalling for nets with the same RD.
Recommended Action This message is informational only. Need to check L2VPN Configuration in the topology across all PEs.
Error Message%ROUTING-BGP-4-L2VPN_SIGNAL_OVERLAP Net [chars] or [chars] is learned via both types of Signalling
Explanation BGP detected that the same prefixwas learned with a signalling type different from what was learned initially. Do not allow both types of signalling for nets with the same RD.
Recommended Action This message is informational only. Need to check L2VPN Configuration in the topology across all PEs.
Error Message%ROUTING-BGP-4-L2VPN_SIGNALLING_MISMATCH Ignored import operation for Net received for L2 table [chars]
Explanation The import operations will not be done for nets whose signalling type does not match that for the importing VRF. The import operation has been ignored.
Recommended Action Check the topology to make sure that tow differently signalled vrfs are using different Signalling types.
Error Message%ROUTING-BGP-4-LOCK_ORDER Locking order violation (thread [unsigned int]): [chars] gained while holding: [chars]
Explanation BGP detected a violation of lock ordering requirements.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-LOCK_RELEASE Lock released without being held (thread [unsigned int]): [chars] gained [unsigned int], released [unsigned int]
Explanation BGP detected a lock being released when it was not held.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-MAXPFXEXCEED No. of [chars] prefixes received from [chars]: [unsigned int] exceed limit [unsigned int]
Explanation Number of prefixes received from a neighbor for a given address family has exceeded the limit configured with the 'max-prefix' command.
Recommended Action Check the prefixes received from the neighbor and verify whether the limit should be increased, or the neighbor is sending more prefixes than expected.
Error Message%ROUTING-BGP-4-MISSING_SUBGRP Detected missing neighbor AF sub-grp. Correcting: [chars]
Explanation BGP detected that a neighbor AF did not correctly belong to an update sub-group. BGP attempted to correct this error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-NBR_DOUBLE_ADD_SCOPED_ILIST Nbr [chars] (state: [unsigned int]) is on Active scoped ilist already
Explanation An attempt to add nbr to active scoped ilist while it is on the ilist already.
Recommended Action None.
Error Message%ROUTING-BGP-4-NSR_UNRECOGNIZED_PATH_INFO Path with uncrecongnized flags synced for net [chars] path id [unsigned int] version [unsigned int] flags [hex]
Explanation A path with unrecognized flags is synced to standby.during NSR sync for a net. This may result in inconsistent state between active and standby BGP which can impact operation after Failover.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-PATH_ELEM_LIMIT Reached the maximum limit ([unsigned int]) of path elements of network [chars] for [chars] address-family
Explanation An attempt was made to create a path element beyond the maximum limit. The advertisement and installation of the network in the BGP table may be inconsistent with additional-paths configuration.
Recommended Action Revisit additional-paths configuration and the total number of paths learned for a particular network.
Error Message%ROUTING-BGP-4-POLICY_COMMUNITY_OVERFLOW Community overflow from policy application
Explanation Policy tried to add more communities than a BGP route can hold.
Recommended Action Find the affected neighbor with 'show bgp community truncated'. Modify policy on the affected neighbor to delete unnecessary communities.
Error Message%ROUTING-BGP-4-POLICY_EBGP [chars] operations in [chars] [chars] policy [chars] will be ignored for external neighbor/update-group [chars]
Explanation A policy attached to an eBGP neighbor performs operations that are illegal for eBGP routes, such as modifying the local-preference.
Recommended Action Modify the policy to avoid the prohibited operations.
Error Message%ROUTING-BGP-4-POLICY_IBGP [chars] operations in [chars] [chars] policy [chars] will be ignored for internal neighbor/update-group [chars]
Explanation A policy attached to an iBGP neighbor performs operations that are illegal for iBGP routes, such as modifying the AS-path or MED.
Recommended Action Modify the policy to avoid the prohibited operations.
Error Message%ROUTING-BGP-4-POLICY_NHOP_WRONGAFI The policy '[chars]' attempted to set a next-hop on [chars] with an unsuitable address type. The next-hop will not be modified.
Explanation The specified route-policy (or a policy applied by that policy) is configured - perhaps on a neighbor or for redistribution - and it is attempting to set the next-hop of the specified route to an address that doesn't match the address-family of the route. For example, it might be setting an IPv6 next-hop on an IPv4 route. Since this does not make any sense, the attempt will be ignored, and the next-hop will not be changed. (Note that this message is rate-limited, so it will not appear for every single route that is affected). Use the command 'show rpl policy name attachpoints' to determine where this policy is in use. Use the command 'show rpl policy name uses policies' to determine which other policies this policy applies (since the relevant 'set next-hop' may be in one of these policies).
Recommended Action Modify the policy so that it sets a next-hop that matches the type of route it is modifying.
Error Message%ROUTING-BGP-4-POTENTIAL_DEADLOCK Potential for deadlock detected: Locks: [chars]
Explanation BGP detected the potential for a deadlock to occur. The process will be restarted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-RIB_REG_FAIL Failed to register BGP protocol with RIB for [chars]: [chars] (error code: [hex])
Explanation An error was encountered during the RIB registration operation for the specified BGP table. This could be due either to a lack of resources on the router or a software problem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-SAME_RD_SET Ignored import policy set operation for same RD import on [chars] path received from [chars]
Explanation The import policy must not perform set operations on paths, received from a PE neighbor, whose RD is the same as the RD for the importing VRF. The set operation has been ignored.
Recommended Action Modify the import policy so that it does not perform the set operation, or use globally unique RDs for VRFs.
Error Message%ROUTING-BGP-4-SPKR_RUNNING BGP AS number has changed from [chars] to [chars] - bgp (speaker) process will be restarted.
Explanation The bpm process was terminated improperly and the speaker process did not receive the notification to terminate. A new bpm process has started with a different AS number due to a new bgp configuration while the speaker process is still running with the previous AS number.
Recommended Action The speaker will be restarted to handle this error. No further corrective action is necessary. However, please contact your Cisco technical support representative to report this error.
Error Message%ROUTING-BGP-4-TABLE_DELINK Deleting table_ctx: [chars] in ACTIVE state
Explanation BGP detected that a table_ctx is being deleted even though it is in active state.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-UNKNOWN_ACL Unknown ACL action: [unsigned int]
Explanation BGP received an unknown action (permit/deny/etc) from the ACL library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-4-WRITE_SOCKET Writing to Socket Failed: [chars]
Explanation BGP detected that a socket write failed This happens in the standby.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-5-ADJCHANGE neighbor [chars] [chars]
Explanation A BGP neighbor has either come up or gone down. This message appears only if the bgp log neighbor changes command is configured for the BGP process.
Recommended Action This informational message normally appears as routers and BGP neighbors go up or down. However, unexpected neighbor loss might indicate high error rates or high packet loss in the network and should be investigated.
Error Message%ROUTING-BGP-5-ADJCHANGE_DETAIL neighbor [chars] [chars]
Explanation A BGP neighbor has either come up or gone down. This message appears only if the bgp log neighbor changes detail command is configured for the BGP process. This is the detailed variant of the neighbor state change message. Included in this message is a list of AFI/SAFI which were advertised (supported) by each end of the session and are common to both. The AFI/SAFI values are defined in RFC 1700, RFC 4760.
Recommended Action This informational message normally appears as routers and BGP neighbors go up or down. However, unexpected neighbor loss might indicate high error rates or high packet loss in the network and should be investigated.
Error Message%ROUTING-BGP-5-BPM_ROUTER_ID No router ID available. Cannot connect to neighbors (retry in [unsigned int] seconds)
Explanation IPARM returned no valid router ID. This is due to lack of a global router ID or a loopback interface.
Recommended Action Try one of the following: 1) Set up a BGP router ID via the `bgp router-id' command in the `router bgp' configuration mode, or 2) Set up a global router ID via the `router-id' command in the global configuration mode, or 3) Set up a loopback interface with an IPv4 address.
Error Message%ROUTING-BGP-5-IO_INITSYNC_FAILED [chars] - set id [hex]
Explanation A problem occurred in TCP sync and retry TCP sync.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-5-LOWMEM_RESET neighbor [chars] reset due to SEVERE low memory condition - use 'clear bgp [chars]' to re-enable
Explanation A SEVERE low memory condition has been encountered on the node where the BGP process is running, and so to free some memory, BGP has reset a neighbor. BGP will continue to reset neighbors periodically until the low memory condition abates. The neighbors which are reset will be shut down until a 'clear bgp' command is used to bring them back up. They will not come up automatically when the low memory condition abates - this is to prevent the node oscillating between memory states.
Recommended Action Free some memory on the system or correct the condition causing the low memory problem, and then use the 'clear bgp address' command to re-enable the neighbors that have been shut down. The 'show bgp all all summary' command can be used to easily see which neighbors are affected.
Error Message%ROUTING-BGP-5-LOWMEM_SHUTDOWN BGP is shutting down due to [chars] low memory condition - use 'process restart bgp location node' to restart
Explanation BGP received a notification that CRITICAL low memory state has been entered, or that SEVERE low memory state has been entered while BGP is in READ-ONLY mode, and consequently it has shut itself down in order to free memory.
Recommended Action Check the memory on the node, and take steps to free memory or to correct the condition which caused the low memory state. Then restart the process using the 'process restart bgp location node' command.
Error Message%ROUTING-BGP-5-MAXPFX No. of [chars] prefixes received from [chars] has reached [unsigned int], max [unsigned int]
Explanation Number of prefixes received from a neighbor for a given address family has reached the warning level configured with the 'max-prefix' command.
Recommended Action Check the prefixes received from the neighbor and verify whether the limit should be increased, or the neighbor is sending more prefixes than expected.
Error Message%ROUTING-BGP-5-NBR_NSR_DISABLED_STANDBY NSR disabled on neighbor [chars] on standby due to [chars]
Explanation A BGP neighbor has NSR disabled on standby temporarily due to transport issues.
Recommended Action This informational message normally appears as routers and BGP neighbors go down on standby if NSR is enabled and neighbor goes down because of session flap or the replicated session on standby get torn down.
Error Message%ROUTING-BGP-5-NSR_STATE_CHANGE Changed state to [chars]
Explanation BGP changed its global NSR state.
Recommended Action This informational message appears when BGP changes its global NSR state.
Error Message%ROUTING-BGP-5-POLICY_RESET Policy configuration change on neighbor [chars] requires HARD reset (clear bgp [chars]) to take effect.
Explanation Automatic soft reset on policy change is not possible as the neighbor does not support ROUTE_REFRESH and 'soft-reconfiguration inbound' is not configured.
Recommended Action Manually clear affected peer at earliest convenience, in order for policy change to take effect.
Error Message%ROUTING-BGP-5-RCVD_NOTIF_BADHOLDTIME [chars]
Explanation A BGP notification message of unacceptable hold time has been received.
Recommended Action This message is informational only.
Error Message%ROUTING-BGP-5-SENT_NOTIF_BADHOLDTIME [chars]
Explanation A BGP notification message of unacceptable hold time has been sent.
Recommended Action This message is informational only.
Error Message%ROUTING-BGP-5-TBLATTR_UNLOCK_MISMATCH_TBLCTX Wrong table context ([chars], [pointer]) is passed in for table attr [pointer] unlock - correct table context [chars] ([pointer])
Explanation A warning was encountered during some operation for tblattr for a table context. The table context passed in is not same as the table context under which the tblattr is created. Normally this message will not cause any issue. In rarely case it might. The message is added for debug purpose only to help the DE to find such cases.
Recommended Action Please include the output of the following commands:
–
–
–
Error Message%ROUTING-BGP-5-TUN_NULL_IFHANDLE --
Explanation --
Recommended Action This message is informational only.
Error Message%ROUTING-BGP-5-TUN_NULL_IFHANDLE2 --
Explanation --
Recommended Action This message is informational only.
Error Message%ROUTING-BGP-6-NBR_NOPOLICY No [chars] [chars] policy is configured for eBGP neighbor [chars]. No [chars] prefixes will be [chars] the neighbor until [chars] policy is configured.
Explanation No routing policy has been configured for the specified eBGP neighbor in the given direction (inbound or outbound) for the address family named. To avoid unintended routing effects, no prefixes will be accepted in that direction until some policy is configured. 'Policy' can be a route-policy, or (for inbound policy) it can be a prefix list.
Recommended Action Configure a route-policy for the neighbor in the given direction. If the desired behavior is to accept/send all routes, the route-policy should contain the single statement 'pass'. If the desired behavior is not to accept/send any routes, the route-policy should contain the single statement 'drop'.
Error Message%ROUTING-BGP-6-NSR_RESTART NSR has been restarted - [chars]
Explanation BGP has restarted NSR due to the reason shown. There is no impact on forwarding.
Recommended Action This message is informational only.
Error Message%ROUTING-BGP-6-WARNING_WRAPPER Warning: A call to [chars] failed unexpectedly: [chars]
Explanation A function call failed unexpectedly. This is probably a system problem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-BGP-7-BPM_CHKPT Failed to checkpoint allocation of [chars]([chars]) to speaker [unsigned int]
Explanation The BPM failed to record the allocation in the checkpoint table. This could cause operational problems if the BPM is later restarted.
Recommended Action No further action is necessary unless the BPM restarts. In that case, if problems are seen it may be necessary to deconfigure BGP completely and then reconfigure it.
Error Message%ROUTING-BGP-7-RIB_TABLE_INFO Unable to [chars] for [chars]. [chars] RIB table [hex]
Explanation A warning was encountered during some operation for the specified address family and RIB table. This could be due a software timing issue, caused by configuration changes.
Recommended Action This behavior is expected, if the table has just been unconfigured. No action is needed unless there are any operational problems.
C12000_IPV4_MRIB Messages
Error Message%ROUTING-C12000_IPV4_MRIB-3-INIT_ERROR Process initialization failed: ([chars]%s)
Explanation MRIB (multicast routing information base) failed to initialize. MRIB is the central routing information base for multicast components. It provides coordination among all multicast routing components and forwarding. The effect is that multicast forwarding will not function. The %s indicates the reason for the failure.
Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times when this error is encountered, to recover. Execute 'show process mrib' to verify that the process is up and running. If it is still non-operational, try doing 'process restart mrib'. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
C12K_MCAST_GTRIE Messages
Error Message%ROUTING-C12K_MCAST_GTRIE-3-ERROR [chars] - [chars]
Explanation This is a development message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-C12K_MCAST_GTRIE-3-INIT_ERR [chars] - [chars]
Explanation This is a development message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-C12K_MCAST_GTRIE-7-DEV_MSG [chars]
Explanation This is a development message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
C12K_MCAST_MDT_EA Messages
Error Message%ROUTING-C12K_MCAST_MDT_EA-3-CONN_ERR Thread connection failed: ([chars]%s)
Explanation The linecard MDT EA thread failed to connect its to the route processor processes during process initialization. The MDT EA process thread handles MDT tunnel interface information between the route processor and the linecard hardware drivers. If the MDT EA fails to connect, no MDT tunnel interfaces can be created or deleted on the line cards. The %s indicates the reason for the failure. The %s is the decoded error reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-C12K_MCAST_MDT_EA-3-THREAD_ERR [chars]%s
Explanation The linecard MDT EA thread failed during platform lib init. The MDT EA process thread handles MDT tunnel interface information between the route processor and the linecard hardware drivers. If the MDT EA fails , no MDT tunnel interfaces can be created or deleted on the line cards. The %s is the pthread library call failure. The %s is the decoded error reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-C12K_MCAST_MDT_EA-7-CHINOOK_DEV [chars]
Explanation A software exception occurred during the initialization of the XR 12000 multicast library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
C12K_MCAST Messages
Error Message%ROUTING-C12K_MCAST-3-CLEANUP_WARN [chars] - [chars] ([hex])
Explanation A software exception occurred during the cleanup of the platform multicast library. This is not a service impacting error but might result into memory leak.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-C12K_MCAST-3-IMC_ERR [chars] - [chars]
Explanation A software exception occurred during interaction with Interface Manager process. This could be due to low memory.
Recommended Action If memory is the issue, reduce other system activity to ease memory demands. If conditions warrant and minimum memory requirements are not met, upgrade to a larger memory configuration. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-C12K_MCAST-3-INIT_ERR [chars] - [chars]
Explanation A software exception occurred resulting in the failure of platform multicast library initialization.
Recommended Action The caller or platform independent module might retry the initialization. If not, then restart this process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-C12K_MCAST-3-INIT_WARN [chars] - [chars] ([hex])
Explanation A software exception occurred during the initialization of the platform multicast library. This is not a major service impacting issue. It impacts just that functional module as mentioned in the error.
Recommended Action If the specified module need to be functional, then reload the LC. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-C12K_MCAST-4-ANOMALY [chars]
Explanation A software exception occurred in platform multicast library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
CLNS Messages
Error Message%ROUTING-CLNS-2-LC_INPUT Unexpected packet num [unsigned int] received on the LC
Explanation CLNS on the LC does not process any packet. It will ignore any packets it receives on the LC.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ASYNC_ATTACH Failed to setup ingress packet handler for NetIO: [chars]
Explanation CLNS encountered errors when initializing its connection with NetIO.
Recommended Action CLNS will restart and try to recover. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-BUNDLE_FSV_REGISTER_FAIL CLNS failed to register with packet process for bundle FSV area: [chars]
Explanation CLNS failed to register with packet manager for FSV area. It only affects the algorithm used to pick a bundle member. If no bundles are configured for ISIS. This error can be ignored.
Recommended Action If the error was seen when a packet process is restarting, then restarting NetIO will help recover from it {or} b If the error is seen in normal conditions it indicates that packet process for some reason is not able to handle the FSV registration request. Please collect the following information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show tech-support pfi all show process packet location show process netio location show logging
Error Message%ROUTING-CLNS-3-CONFIG_INIT Cannot initialize CLNS configuration: [chars]
Explanation CLNS could not initialize its configuration mechanism, and all future CLNS configuration will fail.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-CONN_OPEN Failed to open connection for [chars]: [chars]
Explanation CLNS encountered errors when opening its connection with the process mentioned in the message. CLNS will reattempt the connection by restarting.
Recommended Action CLNS will restart and try to recover. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-DETACH Socket closing on interface [chars] failed: [chars]
Explanation The socket cannot remove an interface when closing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-DLL_REGISTER Registration for '[chars]' failed: [chars]
Explanation Some internal initialization fail miserably.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EDM_CLIENT Error during operation '[chars]': [chars]
Explanation CLNS EDN client (usually a show command) failed to perform certain operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EDM_ENCODE_FAILED Bad encoding failed for [chars]: [chars]
Explanation CLNS failed encode a bag for EDM.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EDM_INIT Operation '[chars]' during EDM initialization failed: [chars]
Explanation CLNS show command failed to initialize the EDM server. 'show' command will likely fail, although CLNS should be able to operate.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_DEBUG_PACKET_INIT CLNS NetIO packet debugging failed to initialize.
Explanation CLNS failed to initialize packet debugging functions.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_DEBUG_RETRIES_EXCEEDED Stopping CLNS debug initialization attempts after [unsigned int] tries
Explanation CLNS tried to initialize packet debugging functions but was unable to succeed even after a number of attempts. No more attempts will be made.
Recommended Action No action is required.
Error Message%ROUTING-CLNS-3-ERR_DROP_PKT [chars]. Dropping packet
Explanation CLNS encountered an internal error while trying to process a packet (usually for output). As a result CLNS dropped the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_INTERFACE_DATA CLNS was unable to resolve an interface while installing cap/decap chain.
Explanation CLNS was unable to look up local interface information. As a result the system may not be able to send/receive ISIS packets over this interface. This may be due to problems with either CLNS or the forwarding infrastructure.
Recommended Action Restarting the CLNS process may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_MEDIA_REGISTER CLNS failed to register media callback with netio: [chars]([dec])
Explanation CLNS failed to register for media callback with netio during initialization. As a result, CLNS will not be able to add its caps and wont receive or send packets. It is an internal error.
Recommended Action Restarting CLNS and/or Netio may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_NETIO_ENCAP_CALLBACK CLNS netio encap callback for media caps: [chars]([dec]) failed [chars]([dec])
Explanation CLNS failed to setup encap callback with this particular media or base encapsulation. As a result CLNS will not be able to receive CLNS packets on this caps on any interface on this node.
Recommended Action Restarting CLNS and/or Netio may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_NETIO_SET_MAPPING CLNS netio set mapping for media caps: [chars]([dec]) failed [chars]([dec])
Explanation CLNS failed to setup mapping with this particular media or base encapsulation. As a result CLNS will not be able to receive CLNS packets on this caps on any interface on this node.
Recommended Action Restarting CLNS and/or Netio may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERR_PARTNER_LOOKUP CLNS-NetIO partner lookup failed
Explanation NetIO was unable to initialize the CLNS partner process. As a result the system will not be able to send/receive ISIS packets over interfaces on this line card.
Recommended Action Restarting CLNS and/or NetIO may clear the error condition. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ERROR_INIT Cannot register CLNS error codes: [chars]
Explanation CLNS could not initialize its error code. CLNS will work, but error messages will not be user friendly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-ETHERENCAP Incorrect MAC address length [dec]
Explanation The MAC address length provided for the ethernet encapsulation is wrong.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EVENT_CONN_CREATE_FAIL Error creating '[chars]' connection: [chars]
Explanation CLNS failed to create a connection to an essential service during initialization. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EVENT_CONN_NOTIFY_FAIL Error registering for critical events on '[chars]' connection: [chars]
Explanation During initialization, CLNS failed to register for essential notifications regarding the state of the connection for the specified service. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-EVM_INIT Error while initializing the [chars]: [chars]
Explanation An operation failed during the initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-GET_TRAFFIC Cannot get traffic information: [chars]
Explanation CLNS show command failed to get the required information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-HSSD_REGISTER_FAIL CLNS failed to register for an HSSD area: [chars]
Explanation CLNS failed to register for an HSSD area. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-INTERFACE Operation '[chars]' on CLNS interface [chars] failed: [chars]
Explanation CLNS could not initialize its interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-L2INFO_LEN [chars] length is [dec], should be [dec]
Explanation The length of the L2 data received is not what it should be.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-LPTS_ADD_BINDING Couldn't add clns binding to lpts port arbitrator, error equals [chars]
Explanation The clns process was unable to add a binding to LPTS. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-LPTS_DELETE_BINDING Couldn't delete CLNS binding from Port Arbitrator, result equals [chars]
Explanation The clns process was unable to delete a binding from LPTS. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-LPTS_SETOPT Cannot set the LPTS option '[chars]': [chars]
Explanation An operation failed during LPTS option setting.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-PAK Packet operation '[chars]' failed: [chars]
Explanation An operation failed during packet handling.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-PAK_READ Failed to read data from packet area: [chars]
Explanation The clns process was unable to read the input packet. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SEND_ASYNC CLNS was unable to wake itself up([dec]) for reading pending packets: [chars]
Explanation CLNS is unable to wake up itself to read the pending ingress packets from NetIO. ISIS will not be able to receive these pending packets from CLNS.
Recommended Action Restarting CLNS might help. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCK_INIT Socket initialisation task '[chars]' failed: [chars]
Explanation An operation failed during socket initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCK_SET_NAME Internal socket error on packet reception: [chars]
Explanation An operation failed during packet reception.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCKET_PARSE_PATH error encountered when parsing path: [chars]
Explanation CLNS was unable to extract the xipc and job id from the socket path. This might cause communication problems between ISIS and CLNS.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-SOCKET_RESMGR_ATTACH Failed to setup the clns socket as a resource manager: [chars]
Explanation The clns process failed to advertise itself to the system as a resource manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-STATSD_INIT Cannot connect to the stats server: [chars]
Explanation An operation failed during the Stats Server Connection opening.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-STATSD_REGISTER Cannot [chars] with the stats server for interface CH[hex] ([hex])
Explanation An operation failed during the Stats Server Interface registration.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-THREAD_CREATE Error starting thread for [chars] processing : [chars]
Explanation CLNS failed to create the thread for the operation mentioned in the message. CLNS will try to recover by restarting.
Recommended Action CLNS will try to recover by restarting. If it recovers no further action is needed. This error is not expected and very rare. It is usually seen when system resources like memory are very low. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-3-TIMESTAMP Operation '[chars]' failed during packet timestamping: [hex] ([chars])
Explanation An operation failed during timestamp processing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-BASE_CAPS_LU_FAIL IM base encapsulation lookup for interface CH[hex] ([hex]) failed: [hex], '[chars]'
Explanation The Interface Manager returned an unexpected error when CLNS attempted to lookup an interface's base encapsulation type. This may be a resource problem but is probably an internal error.
Recommended Action Consider restarting the CLNS and/or Interface Manager processes. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-DEBUG_REGISTER_FAIL Failed to register with the debugging subsystem: [hex], '[chars]'
Explanation CLNS failed to register with the debugging subsystem. If this message has been generated then CLNS debugging may not be available. This may be a system resource problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-ERR_CONN_SETRETRY Error setting the linear retry period for '[chars]': '[chars]'
Explanation CLNS failed to set the linear retry period for connecting to sysdb. Set the retry period in order to avoid immediate reconnection attempt from clns to sysdb server when the latter restarts. This prevents clns from blocking on sysdb and cause any traffic drop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-ERR_IDB_LOOKUP_DROP_PKT [chars]: Netio IDB not found for interface CH[hex] ([hex]), packet 0x[pointer] dropped
Explanation CLNS was unable to find the NetIO IDB for the interface handle in the message. If this is seen during NetIO restart, it could be transient condition that should recover once NetIO is back up with all the IDBs in steady state. If this is seen in steady state, the ISIS adjacency on this interface could be affected.
Recommended Action If this message is seen during NetIO restarts and the message is seen only at that time, no further action is needed. If this message is seen during steady state more than once with the ISIS adjacency on this interface being affected, restarting netio process or improxy process might help in redownloading the IDBs to netio.
Error Message%ROUTING-CLNS-4-GET_MCASTADDR_ERR Failed to get MAC address(im_attr_macaddr_get) for [chars]: [chars]
Explanation The process failed to get MAC address from the interface. This can be caused by a faulty hardware.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-IM_CRE_REG_FAIL CLNS interface registration failed for base cap type [chars]: [chars]
Explanation CLNS process failed to register an interface with the Interface Manager. This is an internal error. It requires a restart of process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-IM_SERV_BIND_FAIL Failed to bind to the Interface Manager: [dec]
Explanation CLNS failed to bind to the Interface Manager control plane. It is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-IM_SIGEVENT_FAIL IM control handler setup failed: [chars]
Explanation CLNS failed to establish signal event in the Interface Manager control plane. It is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-MAC_SIZE_ERR Incorrect MAC address size for [chars] (returned: [dec], expected: [dec])
Explanation MAC address size does not match IEEEBYTES (6 bytes). This can be caused by a faulty hardware.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-NETIO_OUTPUT_FAIL Failed to send packet 0x[pointer] to NetIO on interface CH[hex] ([hex]): [chars]
Explanation CLNS was not able to send a packet to NetIO. This could be because of communication problems between CLNS and NetIO.
Recommended Action If this message is seen during transient conditions, for example when NetIO is restarting either because of install operation OR because NetIO crashed then it is not harmful unless you see ISIS adjacencies dropping. If it is seen under steady state conditions OR If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-PAK_FROM_ISIS_FAIL Failed to process packet 0x[pointer] from ISIS: [chars] [chars]
Explanation CLNS was not able to process a packet from ISIS successfully and hence dropped the packet.
Recommended Action This message could be seen under low packet memory conditions and should recover once packet memory becomes available to CLNS. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-PAK_FROM_NETIO_FAIL Failed to process packet 0x[pointer] from NetIO: [chars]:[chars]
Explanation CLNS was not able to process a packet from NetIO successfully and hence dropped the packet.
Recommended Action This message could be seen under low packet memory conditions and should recover once packet memory becomes available to CLNS. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-SEND_HELLO_PDU_TO_ISIS_FAIL Failed to send Hello PDU(0x[pointer]) type [chars] ([hex]) from interface CH[hex]([hex]) to ISIS instance [chars]: [chars]
Explanation CLNS was not able to send a hello class PDU to ISIS. This could be because of communication problems between CLNS and ISIS.
Recommended Action If this message is seen during transient conditions, for example when ISIS is restarting either because of install operation OR because ISIS crashed then it is not harmful. If the error message says out of memory, it is because of the queue between CLNS and ISIS being FULL which could either be because traffic rate is very high or ISIS might not be reading the packets. If it is seen under steady state conditions OR adjacency flaps are seen on this interface OR Ii the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-SEND_PDU_TO_ISIS_FAIL Failed to send PDU(0x[pointer]) type [chars] ([hex]) from interface CH[hex]([hex]) to ISIS instance [chars]: [chars]
Explanation CLNS was not able to send non-Hello class PDU to ISIS. This could be because of communication problems between CLNS and ISIS.
Recommended Action If this message is seen during transient conditions, for example when ISIS is restarting either because of install operation OR because ISIS crashed then it is not harmful. If the error message says out of memory, it is because of the queue between CLNS and ISIS being FULL which could either be because traffic rate is very high or ISIS might not be reading the packets. If it is seen under steady state conditions OR if the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-TRACE_INIT_FAIL Failed to init debug tracing support : [chars]
Explanation CLNS failed to init with the ltrace subsystem. This affects the debuggability of the component. CLNS will attempt to restart to recover from the situation.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-4-UNKNOWN_MEDIA Unknown media ([dec]) on interface CH[hex] ([hex])
Explanation The specified interface media is not supported by CLNS. This means that IS-IS and other CLNS protocols cannot run over the specified interface. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. As a workaround consider using a different encapsulation for the interface.
Error Message%ROUTING-CLNS-7-CAPS_ADD_FAIL Failed to add CLNS encapsulation to interface CH[hex] ([hex]): [chars]
Explanation CLNS failed to add caps to its encapsulation chain. It is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-7-CONN_PAK_AREA_FAIL CLNS failed to connect to packet area
Explanation CLNS failed to connect to packet subsystem during initialization. As a result, CLNS will not be able to receive or send packets. It's an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-7-DEBUG_THREAD_CREATE Error starting thread for debug registration: [dec]
Explanation CLNS failed to create the thread for debug registration and to handle debug events. Thus, causing unavailability of debugs. But CLNS should continue with the normal functionality, so the process should not exit even if this thread is not created.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-7-ERR_L2_HASH CLNS failed to initialize the L2 hash function: [chars]
Explanation CLNS failed to initialize the L2 hash function. It is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-CLNS-7-ERR_STACKMEM Could not alloca [dec] bytes
Explanation CLNS failed to allocate stack memory space.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-CLNS-7-IM_ATTR_REG_FAIL Failed to register for notification of MAC address: [chars]
Explanation An error was discovered during the Interface Manager MAC address registration. It requires a restart of process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
DAD Messages
Error Message%ROUTING-DAD-3-ERR_EVM_ASYNC_ATTACH Unable to listen for events because: [chars]
Explanation A failure occurred while trying to setup the event listen structure for package un-installs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSDB_BIND Sysdb bind operation failed because: [chars]
Explanation The bind operation has failed for the above reason. This is something that should not occur under normal operations.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSDB_DELETE Sysdb delete operation failed because: [chars]
Explanation The DAD library attempts to delete the old protocol information before writing out the new information. This delete operation failed for the above reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSDB_SET The writing of sysdb information failed because: [chars]
Explanation The DAD library encountered an error while writing out the policy information for the above reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSMGR_PROC_AVAILABLE Unable to declare proc available because: [chars]
Explanation A failure occurred while trying to tell sysmgr that availability is ready.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSMGR_PROC_CLEANUP Unable to listen for cleanup notices because: [chars]
Explanation A failure occurred while trying to ask sysmgr for cleanup events for package un-installs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-3-ERR_SYSMGR_PROC_READY Unable to declare proc ready because: [chars]
Explanation A failure occurred while trying to tell sysmgr that you are ready for processing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-DAD-7-SETUP Invalid setup at [chars]@[dec]: [chars]
Explanation There was something illegal about the setup operations that where performed. This should be a straight coding error that will fail every time and should be cleaned up before releasing the code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
EIGRP_POLICY Messages
Error Message%ROUTING-EIGRP_POLICY-3-ORA_INSTBUILD Failed to build [chars]: [chars] ([chars])
Explanation Internal error in the routing policy library occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP_POLICY-3-ORA_ORABUILD Failed to build ORA[chars]: [chars] ([chars])
Explanation There was an internal error in the routing policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP_POLICY-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in the routing policy library occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
EIGRP Messages
Error Message%ROUTING-EIGRP-2-ERR_MEM_ALLOC [chars] [dec]: Could not allocate memory for [chars]
Explanation There is not enough memory available for the EIGRP process.
Recommended Action This indicates a low-memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-EIGRP-3-ANCHORCOUNT [chars] [dec]: Anchor count negative
Explanation Internal error in the flow control module in EIGRP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-BADCOUNT Invalid path count for route [chars], [dec] successors, [dec] paths
Explanation A bad reference count has been detected while adding a path for a prefix.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-INTERNAL [chars] [dec]: [chars]
Explanation An internal error occurred in EIGRP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-MULTIFLOW Flow control error, [chars], on [chars]
Explanation Error in the flow control algorithm in EIGRP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-NOBUFFER No buffers available for [unsigned int] byte packet
Explanation EIGRP could not allocate a packet buffer to transmitting a packet.
Recommended Action The number of packet buffers available for transmitting EIGRP packets is low. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-EIGRP-3-PAK_WRITE Failed to construct packet to send on [chars]. [chars]
Explanation Error in constructing a packet to be transmitted by EIGRP occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-PEERSEXIST [dec] peers exist on [chars]
Explanation One or more peers exist on an interface which is being deleted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-PFXLIMIT [chars] [dec]: [chars] prefix limit reached
Explanation Number of prefixes for eigrp has reached the configured default limit.
Recommended Action Use 'show ip eigrp accounting' for details on the source of the prefixes and take corrective measures.
Error Message%ROUTING-EIGRP-3-RDBLEFT Interface removed, but route [chars], nexthop [chars] ([chars]), origin [chars], has path
Explanation Routes exist over an interface being deactivated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-REFCOUNT Negative refcount in packet descriptor 0x[pointer]
Explanation Internal reference count error in EIGRP occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-SIA Route [chars] stuck-in-active state in instance [dec]. Cleaning up
Explanation Neighbor was reset to the specified peer, due to a prefix being in stuck-in-active state.
Recommended Action Verify that there are no packet drops between the neighbors and the state of the EIGRP prefix in the neighbor. Clear the eigrp neighbor. If the CPU utilization by EIGRP remains high, restart the EIGRP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-3-UNKTIMER Unknown timer type [dec] expiration
Explanation Unknown timer was encountered in EIGRP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-4-ERR_SOCKET Error [chars]setting [chars] option in [chars]
Explanation EIGRP was unable to set the specified socket option on the specified interface or VRF.
Recommended Action If the message persists, remove and readd the affected interface or VRF and if the problem still persists, restart EIGRP process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-EIGRP-4-PFXLIMITTHR [chars] [dec]: [chars] threshold prefix level reached
Explanation Number of prefixes in the topology database has reached the configured or default threshold level.
Recommended Action Take preventive action by identifying the source of the prefixes. Use 'show ip eigrp accounting' for details.
Error Message%ROUTING-EIGRP-4-WARNING [chars]
Explanation There is a subnet mismatch between eigrp neighbors.
Recommended Action Verify the primary IPv4 address on both ends of the specified interface.
Error Message%ROUTING-EIGRP-5-NBRCHANGE [chars] [dec]: Neighbor [chars] ([chars]) is [chars]: [chars]
Explanation An EIGRP neighbor has gone UP or DOWN.
Recommended Action No action is required.
Error Message%ROUTING-EIGRP-6-EVENT [chars], [chars]
Explanation An EIGRP event logged into the trace buffer.
Recommended Action No action is required.
Error Message%ROUTING-EIGRP-6-PAK_SEND Failed to send packet on [chars]. [chars]
Explanation Failure to send a packet from EIGRP occurred.
Recommended Action This can happen if other processes involved in packet forwarding are restarting. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ENXR_MRIB Messages
Error Message%ROUTING-ENXR_MRIB-3-IFH_ERR Failed to [chars] : [chars]
Explanation This is an internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ENXR_MRIB-3-INIT_ERROR Process initialization failed: ([chars]%s)
Explanation MRIB (multicast routing information base) failed to initialize. MRIB is the central routing information base for multicast components. It provides coordination among all multicast routing components and forwarding. The effect is that multicast forwarding will not function. The %s indicates the reason for the failure.
Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times when this error is encountered, to recover. Execute 'show process mrib' to verify that the process is up and running. If it is still non-operational, try doing 'process restart mrib'. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
EVENT Messages
Error Message%ROUTING-EVENT-3-ERR_MEM_ALLOC No memory, [chars]: [chars]
Explanation Allocation of the specified resource failed because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
FIB_ForUs Messages
Error Message%ROUTING-FIB_ForUs-3-LIB_DEBUG_INIT The ForUs client library debug failed to initialize, event: [chars], error: [chars]
Explanation Initialization of debugging in the ForUs client library failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
FIB Messages
Error Message%ROUTING-FIB-1-FIBALLOC [chars]: [chars]
Explanation The CEF system could not allocate the data structures needed to initialize a new forwarding table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-1-FIBTBLINIT CEF table creation failure, id:[dec] [chars]
Explanation An internal software error occurred that prevented the creation of a new forwarding table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-BGP_ATTR_INSERT_DROP Attribute [hex] insert failed [hex], [chars].
Explanation FIB is dropping this attribute due to error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-IFH_RECYCLE_CLEANUP_EXT_FAIL IFH-RECYCLE: Cleanup of quarantined idb extension failed. Encoded info: IDB_ext:(0x[pointer]) Proto:([chars]) Interface:([hex]). Flags:([hex]), Ref_count:([dec]), NH_count:([dec]), Glean_nhinfo:(0x[pointer]). Detailed info dump at: [chars]
Explanation FIB (CEF) failed to cleanup an IDB on detecting interface handle recycle to a new interface. Some of the routes may be in incorrect state and may affect traffic forwarding for those routes. There is no self recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-INIT FIB initialization failed on this node. Reason: [chars]. Decoded error reason: [chars]
Explanation FIB (CEF) initialization has failed due to the reason indicated in the message. The process shall attempt self recovery by restarting. Without FIB aka CEF up, forwarding shall be impacted on the setup.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-INVALID_MSG FIB thread [chars], received an invalid message. Decoded error reason: [chars]. Encoded return value:([unsigned int])
Explanation FIB (CEF) thread got an invalid message, indicating unexpected behavior so it is exiting. The process shall attempt self recovery by performing graceful restart, where in the FIB shared memory shall be intact. Without FIB aka CEF up, forwarding shall be impacted on the setup.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-NOMEM_ROUTEDROP_ADDMODIFY Dropping add/modify route [chars]/[unsigned int] msg due to low memory.
Explanation FIB is not adding or modifying this route due to a low memory condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-NOMEM_ROUTEDROP_DEL Dropping delete route [chars]/[unsigned int] msg due to low memory.
Explanation FIB is not deleting this route due to a low memory condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-NOMEMINFO_ROUTEDROP Dropping route [chars]/[unsigned int] due to no knowledge of memory available. err [hex], [chars].
Explanation FIB is dropping this route because it is unable to find the memory available.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-NOMEMINFO_SHMERR Dropping routes due to no knowledge of memory available. err [hex], [chars].
Explanation FIB is dropping this route because it is unable to find the memory available.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-OOR CEF has run out of [chars] resource memory. No more route updates will be handled by the CEF. Please delete routes, and then clear the cef on this node to resume normal operation
Explanation The fib_mgr process on the node has detected an out of resource condition for the indicated resource. Normal operation cannot resume until routes are deleted and customer does a clear cef on the node.
Recommended Action Run show cef resource command and check which resource(s) are running low on memory. Significant routes will have to be deleted followed by a clear cef on the affected node to resume normal cef operation.
Error Message%ROUTING-FIB-2-OOR_TBL CEF has run out of table resource memory. This table [hex] could not be created. Please check the memory on the card and then recreate/reconfigure the table when enough memory is available
Explanation The fib_mgr process on the node has detected an out of resource condition for the indicated resource. Normal operation cannot resume until routes/tables are deleted and customer does a recreate of the table.
Recommended Action Run show cef resource command and check which resource(s) are running low on memory. Significant routes/tables will have to be deleted followed by a reconfiguration of the table.
Error Message%ROUTING-FIB-2-PROTO_INIT FIB protocol [chars], initialization failed. Reason: [chars]. Decoded error reason: [chars]. Encoded return value:([unsigned int])
Explanation FIB (CEF) initialization has failed due to one of its protocol, indicated in the message, encountered a failure as indicated in the message. The process shall attempt self recovery by restarting. Without FIB aka CEF up, forwarding shall be impacted on the setup.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-ROUTEDROP_UPD Dropping route update to [chars]/[unsigned int] path [dec] interface [hex]
Explanation FIB is not processing this route update due to internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-SHMRESET_NON_RELOAD_SMU SMU installed will reset shared memory, which will impact traffic till fib_mgr initializes.
Explanation SMU installed has been designed to cause SHM reset without having to reload the router. Till fib_mgr initializes there will be impact on traffic.
Recommended Action None.
Error Message%ROUTING-FIB-2-STATE FIB startup failed at state: [chars]. Decoded error reason: [chars]. Encoded return value:([unsigned int])
Explanation FIB (CEF) initialization has entered into an incorrect state. The process shall attempt self recovery by restarting. Without FIB aka CEF up, forwarding shall be impacted on the setup.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-2-THREAD_INIT FIB thread [chars], initialization failed. Reason: [chars]. Decoded error reason: [chars]. Encoded return value:([unsigned int])
Explanation FIB (CEF) initialization has failed due as a result of one of its threads encountering failure. The reason for which is indicated in the message. The process shall attempt self recovery by restarting. Without FIB aka CEF up, forwarding shall be impacted on the setup.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-ADD CEF : fail to add route for [chars] [unsigned int]
Explanation CEF fails to add a prefix entry.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-ADJ_INIT FIB initialization with the AIB failed [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working with AIB.
Recommended Action Try restarting the fib process to see if the route gets programmed again. LC OIR can be tried as well.
Error Message%ROUTING-FIB-3-ATTRIBUTE Attribute operation failed during [chars]: for [chars] ([dec], [chars])
Explanation An internal software error occurred that prevented the FIB from working with attributes.
Recommended Action Try restarting the fib process to see if the problem goes away.
Error Message%ROUTING-FIB-3-BCDL BCDL failed during [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working properly with BCDL.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-BCDL BCDL failed during [chars] for group [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working properly with BCDL.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-CFGREG Config registration error: [chars] [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.*
Error Message%ROUTING-FIB-3-CLIENT CEF CLIENT: [chars] [chars]
Explanation CEF client internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-CLIENT_ERROR [chars] [chars]
Explanation A FIB client behaved erroneously or there was an unexpected state.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-DEFAULT_ROUTE_CREATE_FAIL Default route creation failed [chars]
Explanation A route update was skipped because of an internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-DELETE CEF : fail to delete route for [chars] [unsigned int]
Explanation CEF fails to delete a prefix entry.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-DUMMY_ZERO_ERR Error while attempting to restore dummy real zero: [hex] [chars]
Explanation Cannot restore the dummy real zero route to its original state
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-DUMMY_ZERO_REMOVE Removing ing dummy real zero because of error: [hex] [chars]
Explanation Forced to delete because cannot restore the dummy real zero because of error
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-FIBGTRIEINIT Gtrie initialization default value failed, [chars] [chars]
Explanation An internal software error occurred that prevented the FIB subsystem from starting.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-GEN_ERR FIB internal error: [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-GTRIE GTRIE failed during [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working with the tries.
Recommended Action Try restarting the fib process to see if the problem goes away.
Error Message%ROUTING-FIB-3-GTRIE_DEL Gtrie delete failed, [chars]/[unsigned int] (Err: [hex], [chars])
Explanation An internal software error occurred that prevented the FIB subsystem from removing a route.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-IDB IDB operation for ifh:[hex] failed during [chars]: ([dec], [chars])
Explanation An internal software error occurred for an IDB action.
Recommended Action Try restarting the fib process to see if the problem goes away.
Error Message%ROUTING-FIB-3-INIT_GR_EXIT_TOUT Timed-out on graceful exit for init failure, exiting ungracefully
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-INTERNAL_ERR An internal processing error/illegal state detected
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-INVALID_BGP_PATH_FLAGS Received Invalid path flags from BGP: [hex], PL: [hex]
Explanation An invalid combination of BGP path flags was received.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-LEAF_DEPEND_CLEANUP_ERR LEAF-DEL-ERR: All dependents of leaf [pointer] did not unlink, leaf-ref-count:[dec] first-dep:[pointer]
Explanation This is an unexpected state where after leaf deletion, leaf still has some dependent paths pointing to it. This could prevent the leaf from getting free.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-MALLOC_FAILED Heap memory allocation failed from - '[chars]'
Explanation FIB could not allocate memory for some internal processing. It might be in consistent state.
Recommended Action Check memory utilization on the card the error came for and take appropriate steps to reduce it.
Error Message%ROUTING-FIB-3-NOMEM Malloc Failure, [chars]
Explanation An internal software error occurred. CEF switching disabled on this slot.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-NOTABLE Failed to find CEF forwarding table [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-PD_FAIL [chars]
Explanation This is a catch all PD errors.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-PFI_FIB_IFTYPE_MISMATCH Mismatch in interface type [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-PFI_IFINFO CEF : [chars] ifh:[hex], if:CH[hex]
Explanation CEF fails to connect or get information from pfi_ifh server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-PLATF_UPD_FAIL Platform upd failed: Obj equals [chars][ptr equals [pointer],refc equals [hex],flags equals [hex]] Action equals [chars] Proto equals [chars]. Cerr equals [chars]
Explanation This is a catch all Platform update errors during development phase.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-RCC CEF : rt_check_send_msg failed: [chars]
Explanation CEF fails to send rcc error messages.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-RCC_NO_TABLE route check to the fib failed table [hex], protocol [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from completing the route check.
Recommended Action Try restarting the fib process to see if the route gets programmed again. LC OIR or clear route * can be tried as well.
Error Message%ROUTING-FIB-3-RCC_TABLE RCC failed finding [chars] table
Explanation The Route Consistency Checker failed finding specified table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-RECURSIVE_LOOP [chars]
Explanation This is to catch recursive loops.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-RETRY retry module failed [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from retrying a failed operation.
Recommended Action Try restarting the fib process to see if the route gets programmed again. LC OIR or clear route * can be tried as well.
Error Message%ROUTING-FIB-3-ROUTE route update for [chars] (table [hex]) to the fib failed [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working with route updates.
Recommended Action Try restarting the fib process to see if the route gets programmed again. LC OIR or clear route * can be tried as well.
Error Message%ROUTING-FIB-3-ROUTE_GEN [chars]: [chars]
Explanation An internal software error occurred during route handling.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-RPCINIT Unable to initialize CEF RCP handler: [chars] program [dec] version [dec] protocol [dec]
Explanation The CEF system could not initialize an RPC server and therefore cannot handle show and clear commands from the parser.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-SERVER CEF SERVER: [chars] [hex]
Explanation CEF server internal error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-SERVER_CERR CEF SERVER: [chars] [chars]
Explanation CEF server internal error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-SHM shared memory failed during [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working properly with shared memory.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-SHMEM Shared memory failure: error code [dec], [chars]
Explanation An internal error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-TABLE table operation failed during [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB from working with multiple tables.
Recommended Action Try restarting the fib process to see if the problem goes away.
Error Message%ROUTING-FIB-3-TE_CREATE_ERR TE-CREATE-ERROR: [chars]
Explanation An error occurred during TE programming.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-TE_DESTROY_ERR TE-DESTROY-ERROR: [chars]
Explanation A te-tunnel created with DOWN backup was destroyed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-THREAD Thread processing error: [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-3-TIMER Timer module failed [chars]: [chars]
Explanation An internal software error occurred that prevented the FIB handling timers.
Recommended Action Try restarting the fib process to see if the route gets programmed again. LC OIR or clear route * can be tried as well.
Error Message%ROUTING-FIB-4-FIBIDB Missing cef idb for ifh:[hex], CH[hex], during [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-FIBIDB_LOOKUP_FAIL FIB idb lookup failed ifh [hex], if:CH[hex] [chars]: [hex], [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-HA [chars]: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-IDB_PLATF_UPDATE_TOO_LONG Platform update type - [chars] for interface [chars] (idb 0x[pointer], protocol [chars]) took too long - [dec] secs
Explanation You do not expect platform updates to take too long. This can block other processes that need to communicate with fib_mgr, for instance, for config, etc.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-IM_CONN fail to connect to IM [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-IM_CONN fail to connect to IM [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-INIT IP CEF initialization failure: [chars]
Explanation Initialization of CEF failed.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-LCL_ATTRIB_ENTER_OOR Proto:[chars], VRF:[chars], Local attribute index database max([dec]) reached. OOR state: red
Explanation The local attribute index database on the LC has reached its maximum.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-LTRACE_ERR Failed to open trace file: [chars]
Explanation The FIB process was unable to open the trace buffer for automatic tracing (show trace cef may not work).
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-PFI_IFH_CONN fail to connect to PFI_IFH [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-PFI_IFH_LOOKUP fail to lookup information in PFI_IFH [chars] for ifh [hex]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-PULSE_HNDLR FIB received unidentifiable pulse: proto [unsigned int], opc [unsigned int], [chars]
Explanation FIB received a pulse that could not be identified.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-4-RADIXINIT Error initializing IP CEF radix tree
Explanation Initialization of the radix tree could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-FIB-4-RSRC_LOW CEF running low on [chars] resource memory. CEF will now begin resource constrained forwarding. Only route deletes will be handled in this state, which may result in mismatch between RIB/CEF. Traffic loss on certain prefixes can be expected. The CEF will automatically resume normal operation, once the resource utilization returns to normal level
Explanation The fib_mgr process has detected that average utilization for specified resource has risen above a predefined high watermark value, and has entered resource constrained forwarding mode. In this mode, the cef will only handle route deletes which may potentially free up some memory. Due to this operational mode, the CEF/RIB will be out of sync. Once routes are deleted and resource utilization level drops to acceptable levels again, cef will come out of this operational mode and resume normal operation.
Recommended Action Run show cef resource command and check which resource(s) are running low on memory. Any action that reduces number of routes for this protocol (results in route delete events to free up resources below predefined level) will eventually result in the cef returning to normal operation after few seconds.
Error Message%ROUTING-FIB-4-WARNING FIB internal error [chars]: [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-5-ROUTE_UPDATE_DROP [chars]
Explanation An internal software error occurred, and FIB had to throw away a route update.
Recommended Action Try restarting the fib process to see if the problem goes away.
Error Message%ROUTING-FIB-6-DEBUG_REG IPV4-FIB: Debug registration failed: [chars]
Explanation Debug message registration failed.
Recommended Action No action is required.
Error Message%ROUTING-FIB-6-DEPEND_UNBIND_FAILURE Unbind for object type [chars] failed from parent type [chars] - no unbind handler found
Explanation FIB internal APIs need/expect an unbind handler, which was not found. This can lead to FIB not cleaning up state on interface delete events.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-6-HARD_RESET [chars]
Explanation FIB is restarting with a reset of its shared memory to possibly recover from an unrecoverable state.
Recommended Action None.
Error Message%ROUTING-FIB-6-LCL_ATTRIB_EXIT_OOR Proto:[chars], VRF:[chars], Local attribute index database OOR state: green. OOR local attribute count:[dec]
Explanation The local attribute index database on the LC has resources available.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-FIB-6-RSRC_OK CEF resource state has returned to normal. CEF has exited resource constrained operation and normal forwarding has been restored
Explanation The fib_mgr process had previously detected that the hardware and software resources required for cef operation were running low, and had entered resource constrained forwarding. Now resources have been restored and cef has resumed normal operation.
Recommended Action None.
FWD_HA Messages
Error Message%ROUTING-FWD_HA-4-PROCESS_RESTART [chars] restart_count equals [dec] mode equals [dec] ([chars])
Explanation The process is being restarted either because you failed to initialize or you finished resetting shared memory and you are starting fresh.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
HFR_IPV4_MRIB Messages
Error Message%ROUTING-HFR_IPV4_MRIB-3-CHKPT_ERR Failed to [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_ADD_ERR Failed to add LC [dec] into FGID [dec]: [chars]
Explanation Internal error.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_ERR Failed to [chars]: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FGID_REMOVE_ERR Failed to remove LC [dec] from FGID [dec]: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-FILE_OPEN_ERR Failed to open a file [chars] to dump the [chars] database
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-IFH_ERR Failed to [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-IM_NAME_ERR im_interface_name error in function [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-INIT_ERR Failed to [chars]
Explanation Init error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-INTERNAL_ERR Failed to [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-INVALID_FGID_ERR Failed to [chars] : invalid fgid value [hex]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-MEM_ERR Failed to [chars] for [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-HFR_IPV4_MRIB-3-PERF_ERR Failed to [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IGMP_MTRACE Messages
Error Message%ROUTING-IGMP_MTRACE-3-EVENT_ERROR Event error: [chars] in [chars]
Explanation Event error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-INIT_ERROR Init error: [chars]
Explanation Initialization error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-MEMORY_ERROR Memory error: [chars] in [chars]
Explanation Memory error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-MSG_ERROR msg error: [chars] in [chars]
Explanation Messaging error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGMP_MTRACE-3-SOCKET_ERROR Socket error: [chars] in [chars] : [chars]
Explanation Socket error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IGPTE_LIB Messages
Error Message%ROUTING-IGPTE_LIB-3-ERR_BAG_REGISTER Error registering igpte-lib [chars] bags: [hex], '[chars]'
Explanation IGP failed to register its bag files with the bag library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGPTE_LIB-3-ERR_DBG_REGISTER Error registering for IGP debug events: [hex], '[chars]'
Explanation IGP failed to register with the debug module for printing messages.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGPTE_LIB-3-ERR_LTRACE_INIT Error initializing LTRACE buffers: [hex], '[chars]'
Explanation A process failed to initialize internal tracing buffers in the IGP/TE API DLL.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IGPTE_LIB-3-ERR_SYSDB_BIND Failed to bind to SysDB: error [hex] ([chars])
Explanation An error occurred when accessing the system database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The process must be restarted before it can function correctly.
Error Message%ROUTING-IGPTE_LIB-3-ERR_SYSDB_REG_NOTIFY Failed to register for [chars] notifications: error [hex] ([chars])
Explanation An error occurred when accessing the system database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The process must be restarted before it can function correctly.
Error Message%ROUTING-IGPTE_LIB-3-ERR_SYSDB_UNREG_NOTIFY Failed to unregister for [chars] notifications: error [hex] ([chars])
Explanation An error occurred when accessing the system database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The process must be restarted before it can function correctly.
Error Message%ROUTING-IGPTE_LIB-4-CLIENT_ERR_MEM_ALLOC Failed to allocate [unsigned int] bytes for '[chars]'
Explanation The process failed to allocate memory for the specified resource.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-IGPTE_LIB-4-DATA_QUEUE_FULL message queue is full. Cannot accept more element.
Explanation Data queue is full and it cannot accept more element. It could be a result of memory limitation.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-IGPTE_LIB-4-ERR_MEM_ALLOC Failed to allocate [unsigned int] bytes for '[chars]'
Explanation The process failed to allocate memory for the specified resource. This could be because the topology is too large for the memory installed in the router.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-IGPTE_LIB-4-INVALID_TLV Data ([dec]) is too big or small([dec])
Explanation Failure to send data due to the limitation of the buffer size occurred. This is an internal error. It requires to reduce the number of interfaces.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-IGPTE_LIB-4-SERVER_ERR_CLINFO_HOLD Error in saving client's message channel information
Explanation IGP failed to save its client's message channel information. This could be a result of channel down or resource allocation failure.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-IGPTE_LIB-4-SERVER_ERR_CLINFO_UNHOLD Error in releasing client's message channel information
Explanation IGP failed to release its client's message channel information. This could be a result of channel down already.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
IP_STATIC_BFD_SESSMGR Messages
Error Message%ROUTING-IP_STATIC_BFD_SESSMGR-4-UNSUPPORTED_INTERFACE : [chars]
Explanation The nexthop is resolved over an unsupported BFD interface.
Recommended Action Pick different nexthop to create the BFD session.
IP_STATIC Messages
Error Message%ROUTING-IP_STATIC-3-IDB_DELETE Failed to delete idb for interface [chars] from '[chars]' thread
Explanation The static routing process failed unexpectedly to delete an interface descriptor block from the idb WAVL tree.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-INTERNAL [chars]: [chars]
Explanation The static routing process has either failed a function that expected to succeed, or has got into an inconsistent state.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
Error Message%ROUTING-IP_STATIC-3-ITAL_EVENT Error processing [chars] event for [chars] from ITAL, table [hex] : [chars]
Explanation A static routing process failed unexpectedly when processing an IP address change event. This may lead to spurious or missing connected and local routes in the routing table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-ITAL_INTERFACE_CREATE Error handling create event for interface [chars]: [chars]
Explanation The static routing process failed to correctly handle a create event for an interface which it was tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
Error Message%ROUTING-IP_STATIC-3-ITAL_TDB_REGISTER_FAILED A static routing process failed function ip_static_ital_vrf_register for table [chars]: [chars]
Explanation A static routing process failed to register a table with ITAL. This may lead to routes associated with a the failed to be added in the routing table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-NHDB_DELETE Failed to delete nhdb for next-hop [chars] for table [hex]
Explanation The static routing process failed unexpectedly to delete an next-hop descriptor block from the nhdb AVL tree.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-PATH_BP_DELETE Failed to delete backpointer to path [chars]/[unsigned int] from [chars] [chars]
Explanation The static routing process failed unexpectedly to delete a path from an interface or next-hop descriptor block's path backpointer list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-RIB_BATCH [chars]: Failed to send RIB batch buffer re-populating RIB for table [hex]: [chars]
Explanation The static routing process failed unexpectedly to update RIB with a batch of updates.
Recommended Action Check the routing table to see whether any static routes are missing (Use 'show route static'). Please contact TAC only if the error is persistent. If the error is transient especially when the RIB process has gone down like in case of failover, and there is no functionality impact then it is ok to ignore this message.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_PREFIX Error re-installing route after a clear table event for prefix [chars]/[unsigned int] in table [hex]: [chars]
Explanation There was an error re-installing a route in the RIB after receiving a 'clear prefix' event.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_TABLE Error re-installing routes after a clear table event for table [hex]: [chars]
Explanation There was an error re-installing routes in the RIB after receiving a 'clear table' event.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_UNKNOWN_PREFIX Received a clear event for unknown prefix [chars]/[unsigned int] in table [hex]
Explanation The static routing process received a clear event from RIB for a prefix which it was not tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
Error Message%ROUTING-IP_STATIC-3-RIB_CLEAR_UNKNOWN_TABLE Received a clear event for unknown table [hex] (Prefix [chars])
Explanation The static routing process received a clear event from RIB for a table which it was not tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
Error Message%ROUTING-IP_STATIC-3-RIB_ECMP Failed to update RIB after ECMP recalculation for table [hex], prefix [chars]/[unsigned int]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after an ECMP recalculation.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
Error Message%ROUTING-IP_STATIC-3-RIB_FETCH Error fetching event from RIB: [chars]
Explanation The static routing process failed unexpectedly to fetch a notification event from RIB.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
Error Message%ROUTING-IP_STATIC-3-RIB_FULL Failed to update RIB during full topology download for table [hex], prefix [chars]/[unsigned int]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after RIB restarted.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
Error Message%ROUTING-IP_STATIC-3-RIB_INTERFACE Failed to update RIB for table [hex], prefix [chars]/[unsigned int], after receiving interface state event for [chars]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after an interface state change event.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
Error Message%ROUTING-IP_STATIC-3-RIB_NEXTHOP Failed to update RIB for table [hex], prefix [chars]/[unsigned int] after receiving next-hop resolution event for [chars]: [chars]
Explanation The static routing process failed unexpectedly to update RIB after a next-hop resolution event.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
Error Message%ROUTING-IP_STATIC-3-RIB_NEXTHOP_REGISTER Failed to register next-hop notification with RIB for table [hex], prefix [chars]: [chars]
Explanation The static routing process failed unexpectedly to register a next-hop resolution event. Future state change events on the next-hop may cause further messages to be generated by the static process.
Recommended Action Check the Next-hop table in static to see whether any static next-hops have been registered or not. Use 'show static next-hop' and 'show rib next-hop ipv4_static/ipv6_static'.
Error Message%ROUTING-IP_STATIC-3-RIB_NEXTHOP_UNREGISTER Failed to unregister next-hop notification with RIB for table [hex], prefix [chars]: [chars]
Explanation The static routing process failed unexpectedly to unregister a next-hop resolution event. Future state change events on the next-hop may cause further messages to be generated by the static process.
Recommended Action Check the Next-hop table in static to see whether any static next-hops have been unregistered or not. Use 'show static next-hop'.
Error Message%ROUTING-IP_STATIC-3-RIB_TOO_MANY_PATHS Prefix [chars]/[dec]: Maximum path count exceeded. Please remove (next-hop [chars], interface [chars]) from the running configuration.
Explanation The maximum allowed number of next-hop paths for a single destination prefix has been exceeded. One or more paths have not been installed in the RIB, and should be removed from the running configuration.
Recommended Action Excess next-hop paths should be removed from the running configuration.
Error Message%ROUTING-IP_STATIC-3-SHUTDOWN Process is shutting down: [chars]
Explanation The static routing process has performed a graceful shutdown and will be restarted.
Recommended Action Check to make sure the process has restarted. If not, restart manually Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-TDB_DELETE Failed to delete tdb for table [hex]'
Explanation The static routing process failed unexpectedly to delete a table descriptor block from the tdb AVL tree.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-TDB_REGISTER_FAILED A static routing process failed function ip_rib_protocol_register for table [hex]: [chars]
Explanation A static routing process failed to register a table with RIB. This may lead to routes associated with a the failed to be added in the routing table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative, and provide the representative with the gathered information.
Error Message%ROUTING-IP_STATIC-3-UPDATE_COMPLETE Failed to send 'update complete' notification to RIB for table [hex]: [chars]
Explanation The static routing process unexpectedly failed an attempt to signal to the RIB that the given table is now in sync.
Recommended Action Check the routing table to see whether any static routes are missing (Use 'show route static'), and whether the protocol is in sync (Use 'show rib clients protocol').
Error Message%ROUTING-IP_STATIC-6-CONFIG_MAXIMUM_CHANGE The maximum number of configurations for static routes has been changed from [unsigned int] to [unsigned int]
Explanation The maximum number of static route configurations which may be entered has been changed.
Recommended Action Refer to the configuration guidelines for the maximum allowed limit for static routes
Error Message%ROUTING-IP_STATIC-6-NHDB_LOCAL The next-hop [chars] for table [hex] is a local route. The static route(s) that has the matching next-hop will not be installed.
Explanation The nexthop of a static route is a local route. This is an invalid configuration.
Recommended Action Check configuration for the static route and its next-hop.
Error Message%ROUTING-IP_STATIC-6-NHDB_OUT_OF_SUBNET The next-hop [chars] for route [chars] in vrf [chars] is outside of the subnet for [chars] and will not be installed in the routing table.
Explanation The nexthop of a static route is outside of outgoing interface. This is an invalid configuration.
Recommended Action Check configuration for the static route and its next-hop.
Error Message%ROUTING-IP_STATIC-6-NHDB_OUT_OF_SUBNET The next-hop [chars] for route [chars] in vrf [chars] is outside of the subnet for [chars] and will not be installed in the routing table.
Explanation The nexthop of a static route is outside of outgoing interface. This is an invalid configuration.
Recommended Action Check configuration for the static route and its next-hop.
Error Message%ROUTING-IP_STATIC-6-NHDB_WITHIN_SUBNET The next-hop [chars] for route [chars] in vrf [chars] which was previously outside of the subnet for [chars], is now within the subnet and will be installed in the routing table.
Explanation The nexthop of a static route was outside of outgoing interface. Now it has resolved through the same interface so became valid configuration.
Recommended Action Check installed routes for the static route.
Error Message%ROUTING-IP_STATIC-7-ITAL_INTERFACE_EVENT Received a [chars] event for unknown interface [chars]
Explanation The static routing process received a change notification event from ITAL for an interface which it was not tracking.
Recommended Action Check the routing table to see whether any static routes are missing. Use 'show route static'.
IPMC_GTRIE_DEBUG Messages
Error Message%ROUTING-IPMC_GTRIE_DEBUG-3-ERR [chars]
Explanation This is a catch all error message. It usually means an uncorrected problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEBUG-3-INIT_ERR [chars] [dec] [chars] [dec] [chars]
Explanation This is an internal error. GTRIE debug library initialization failed.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEBUG-6-TERM_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal non-serious error occurred. GTRIE debug library termination failed.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPMC_GTRIE_DEFAULT Messages
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-2-FATAL [chars]
Explanation Internal error occurred. Usually severe problems such as failing to free memory occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-3-INIT_ERR [chars]
Explanation Error while initializing Gtrie occurred. Initialization failed and aborted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-4-INIT_WARN [chars]
Explanation Error while initializing Gtrie occurred. Initialization will continue.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPMC_GTRIE_DEFAULT-4-WARN [chars]
Explanation Internal error occurred. A significant event but it can still continue.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_ADJ Messages
Error Message%ROUTING-IPV4_ADJ-3-ADD_DB_MALLOC_FAIL Malloc Failure in trying to add adj for [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_ADJ-3-ENT_UPDATE Update for ifh:[hex], if:CH[hex], [chars] skipped. Reason: either no fib or netio IDB
Explanation The layer 2 adjacency could not be installed for the interface. This might cause problems in forwarding traffic to this interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_ADJ-3-L2_LOADHASH_FAIL Could not register ipv4 l2 loadhash function with AIB. Error equals [chars]
Explanation Call to register IPv4 l2 loadhash function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_ADJ-3-NO_FIBIDB IP-ADJ: No fibidb
Explanation Adding an adjacency to the adjacency database failed. Reason for this failure is no fib IDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_ADJ-4-ADD_DB Update for ifh:[hex], if:CH[hex], [chars] failed. Unable to update database
Explanation The layer 2 adjacency could not be installed for the interface. This might cause problems in forwarding traffic to this interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_ADJ-4-LARGE_MAC IP-ADJ([chars]): macaddr change out of bounds
Explanation Extra large MAC change occurred.
Recommended Action No action is required.
Error Message%ROUTING-IPV4_ADJ-6-DEBUG_REG ipv4_adj: Debug registration failed: [chars]
Explanation Debug message registration failed.
Recommended Action No action is required.
Error Message%ROUTING-IPV4_ADJ-7-INV_MSG_CODE Unknown aib message opcode [dec]
Explanation The event manager passed an unknown message code.
Recommended Action No action is required.
IPV4_IGMP Messages
Error Message%ROUTING-IPV4_IGMP-3-ARM_UPDATE_ERR Interface [chars][[hex]] has vrf [chars] vrf_id [hex] set, New vrf [chars] vrf_id [hex]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-CHUNK_ERR Failed to create chunk for [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-CONTEXT_REG_ERR [chars] [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-EDM_INIT ERROR : [chars] - [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-GROUP_ADD_ERR [chars]Fail to add [chars] into group database
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-GROUP_ERR [chars]Group [chars] failed: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-GROUP_FIND_ERR Fail to find [chars] in group database
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_ADD_ERR [chars]Fail to add [chars] into database
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_FREE_ERR [chars]Fail to free [chars] from database: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_HANDLE_MISMATCH_ERR [chars]Interface [chars][[hex]][stale [chars]] handle mishmatch, handle in IM update [hex]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_INIT_ERR [chars] - [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_LOST_GROUPS_ERR [chars]Local joined groups on [chars] will be lost
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_PRESENT_ERR [chars]Interface [chars][[hex]] is still present in vrf [chars]. check_idb [chars][[hex]] loc [dec]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_STATE_MONITOR_ERR [chars]Fail to monitor interface state of [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_VERIFY_ERR [chars]Interface [chars](context [chars]) doesn't belong to context [chars], please clear config error
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IDB_VERIFY1_ERR [chars]Interface [chars] has configured under context [chars] already
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IM_BATCH_STATE_ERR [chars]Invalid state for IM state registration batch on [chars] ([chars])
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-IM_BULK_ERR Failed to [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-INIT_ERR [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-JOIN_IN_SSM_RANGE [chars]%s [chars] in SSM range. Join operation postponed
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-LTRACE_ERR Failed to [chars]: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-MRIB_CONN_ERR MRIB connection error - [chars] in [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-NET_ERR [chars]%s : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SOCK_ERR [chars]%s : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_BIND_ERR Sysdb Bind error for [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_BSCAN_ERR [chars]Sysdb backend scan failed for [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_INIT ERROR : [chars] - [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-SYSDB_REG_ERR Sysdb Registration error : [chars] for [chars] [[chars]]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-WDSYSMON_EVENT_ERROR Received an invalid event from WDSysmon
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-3-WDSYSMON_REGISTER_ERROR [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-4-OOM_STATE_THROTTLE Received [chars] memory depletion warning, stop creating new igmp state
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-4-OOM_STATE_UNTHROTTLE Node memory back to normal, new igmp states will be created
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-4-OOR_WARN [chars]%s: [dec]
Explanation Maximum number of group accepted, either per interface or globally.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-6-ACCESS_GROUP_INFO [chars]ACL applied, removed [chars] from [chars]
Explanation ACL applied to interface on which denied groups join previously.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_IGMP-6-IPARMS_UPDATE_ERR Dropping iparms update: type [chars] for [chars] [[hex]]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MCAST_CHKPT Messages
Error Message%ROUTING-IPV4_MCAST_CHKPT-3-ERR Failed to [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MCAST_NETIO_DEBUG Messages
Error Message%ROUTING-IPV4_MCAST_NETIO_DEBUG-3-INIT_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal error occurred. Multicast NetIO debug library initialization failed.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MCAST_NETIO_DEBUG-6-TERM_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal non-serious error occurred. Mcast netio debug library termination failed.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MFWD_HFR Messages
Error Message%ROUTING-IPV4_MFWD_HFR-5-ERR_SYSDB_INIT [chars] : [chars]
Explanation The MFWD-HFR library encountered internal error during Sysdb init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-7-ERR_BAG_REGISTRY Couldn't register bags : [chars]
Explanation The MFWD-HFR library encountered internal error during sysdb/edm init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-7-ERR_EDM_REGISTER Couldn't register edm : [chars]
Explanation The MFWD-HFR library encountered internal error during EDM init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_HFR-7-ERR_GEN [chars] failed : [chars]
Explanation MFWD-HFR library encountered error during setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MFWD_VKG Messages
Error Message%ROUTING-IPV4_MFWD_VKG-3-INACTIVE_FLOW [chars] ([chars],[chars]/[dec]) has been detected.
Explanation Inactive flow has been detected. This error is normally cause by lack of traffic from the source due to errors.
Recommended Action If the error persists, determine the cause and take appropriate action.
Error Message%ROUTING-IPV4_MFWD_VKG-3-INACTIVE_FLOW [chars] ([chars],[chars]/[dec]) has been detected.
Explanation Inactive flow has been detected. This error is normally cause by lack of traffic from the source due to errors.
Recommended Action If the error persists, determine the cause and take appropriate action.
Error Message%ROUTING-IPV4_MFWD_VKG-5-ERR_SYSDB_INIT [chars] : [chars]
Explanation The MFWD-ASR9K library encountered internal error during Sysdb init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_VKG-5-ERR_SYSDB_INIT [chars] : [chars]
Explanation The MFWD-VIKING library encountered internal error during Sysdb init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_VKG-7-ERR_BAG_REGISTRY Couldn't register bags : [chars]
Explanation The MFWD-ASR9K library encountered internal error during sysdb/edm init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_VKG-7-ERR_BAG_REGISTRY Couldn't register bags : [chars]
Explanation The MFWD-VIKING library encountered internal error during sysdb/edm init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_VKG-7-ERR_EDM_REGISTER Couldn't register edm : [chars]
Explanation The MFWD-ASR9K library encountered internal error during EDM init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_VKG-7-ERR_EDM_REGISTER Couldn't register edm : [chars]
Explanation The MFWD-VIKING library encountered internal error during EDM init setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_VKG-7-ERR_GEN [chars] failed : [chars]
Explanation MFWD-VIKING library encountered error during setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD_VKG-7-ERR_GEN [chars] failed : [chars]
Explanation MFWD-ASR9K library encountered error during setup. The init setup will be retried for finite number of retries.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MFWD Messages
Error Message%ROUTING-IPV4_MFWD-3-ADJ_CREATE [chars] [chars] : [chars]
Explanation Internal error occurred. Cannot create the adjacency for a particular interface. Retries occur for few times.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-BOUNDARY_FAIL [chars] [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR [chars]
Explanation These are unexpected errors.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_AIB_FINT [chars]: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_AIB_MAP Failed to map AIB table: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_AIB_ZERO_ALL [chars]: [chars]
Explanation Failure to set all cached adjacencies to zero occurred when received ELIBBAD from AIB.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_DEBUG_INIT_EVENT Failed to initialize and chain together the debug event descriptors : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_DEBUG_REG Sysdb registration for debug config failed : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_ASYNC_ATTACH [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_CONN_CREATE Event connection create for [chars] failed: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_CONN_NOTIFY Event connection notify for [chars] failed: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_CONN_OPEN Event connection open for [chars] failed: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_CONN_SETRETRY Event connection setretry for [chars] failed: [chars]
Explanation Error while setting event connection setretry occurred. This will cause ipv4_mfwd_partner and ipv6_mfwd_partner processes to exit. When process exists, sysmgr will automatically respawn the process for some number of times. If it still fails, process remains in the exit state. This will impact multicast forwarding.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_CREATE Cannot create event manager : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_INIT_EVENT [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_TIMER_ATTACH [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_EVM_TIMER_LEAF_NEW [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IDB_INIT Cannot initialize IDB library : [chars]
Explanation Failure while initializing IDB library occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IFH Failed to [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IFH_BIND Failed to initialize pfi ifh connection: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IFH_INIT Failed to initialize IFH server : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IFH_UNBIND Failed to [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IM_CNTL_SVR_BIND Failed to initialize im control server connection: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_IMC_CAPS_DATAPATH_CONTROL im_caps_datapath_control error for [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_MEM_ALLOC [chars]
Explanation These are unexpected errors.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_MEM_ALLOC_ARM_IDB [chars] [hex]
Explanation These are unexpected errors.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_MLIB_INIT [chars] [chars]
Explanation Failure while initializing multicast library occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_MRIB_INIT Failed to initialize MRIB connection : [chars] failed : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_NSF_INIT Failed to initialize Multicast NSF : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_PAK_CLIENT_CONN Failed to initialize packet connection: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SHMWIN [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_BAG_DECODE Error in bag decoding : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_BAG_FREE_INDIRECTIONS Error in bag free : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_BAG_REG Couldn't register bags : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_BSCAN SysDB operation [chars] failed: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_DATALIST_FREE Error in datalist free : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_DATALIST_NEXT Error in datalist next : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_EDM_FNS_INIT SysDB operation [chars] failed: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_EDM_REG SysDB operation [chars] failed: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_REG_NOTIFY SysDB operation [chars] failed: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-ERR_SYSDB_REG_VERIFY SysDB operation [chars] failed: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-EXIT Unexpected exit
Explanation Internal error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-GEN_ERR [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-GROUP_ERR [chars] [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-HA [chars]: [chars]
Explanation Error while doing an HA operation (e.g. starting frequent restart monitor) occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IARM_ERR [chars] [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IDB_FAIL [chars] operation failed on [chars] [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-IM_LOOKUP_FAILED IM lookup failed for [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-INSTALL [chars] : [chars]
Explanation Error while performing upgrade/downgrade/install operation occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-LRD_ERR [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-MAX_CONN_RETRY Cannot connect to [chars] using event conn Mgr after [dec] retries: [chars]
Explanation The maximum number of retries to connect to server using event conn was reached.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-MAX_DISABLE_RETRY Failed to disable multicast after [dec] retries: [chars]
Explanation The maximum number of retries to disable multicast was reached.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-MAX_ENABLE_RETRY Failed to enable multicast [dec] retries: [chars]
Explanation The maximum number of retries to enable multicast was reached.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TABLE_OPERATION_FAIL [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TABLE_OPERATION_FAIL_GLACIAL [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TRANSACTION_PENDING_FLAG [chars] : [chars]
Explanation Failure to clear, set, or get transaction pending flag occurred. That can only happen if the APIs to do that are called before shared mem window is opened, or if there is a bug.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-3-TTL_CFG_FAIL [chars] [chars]: [chars]
Explanation Failure to apply a TTL threshold config occurred. The operation will be retried.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ADJ_CREATE_RETRY [chars] [chars] : [chars]. Retrying
Explanation Internal error: Failure to create the adjacency for a particular interface occurred. Retries occur for few times.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-CLEAN_ALL_FAIL [chars] [chars]
Explanation Failure while doing all resource cleanup occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_AIB_UPDATE Failed to [chars] AIB for interface [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_LTRACE_INIT [chars] [chars]
Explanation Error occurred while enabling mcast.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_MRIB_INIT_RETRY Failed to initialize MRIB connection in [chars]. Retrying later: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_MRIB_SEND_RESPONSE_RETRY Failed to post signal to MRIB in [dec] retries. Resetting connection: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_RETRY_INIT [chars]: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_RETRY_TRANS_INIT [chars]: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_RETRY_TRANS_REG [chars]: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-ERR_RETRY_TRANS_SPEC_INIT [chars]: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-FROM_MRIB_UPDATE MFIB couldn't process update from MRIB : [chars] - [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-FROM_MRIB_UPDATE_GLACIAL MFIB couldn't process update from MRIB : [chars] - [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-SVD_ERR [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-TERMINATE [chars] [chars]
Explanation Error occurred while disabling mcast.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-TO_MRIB_MDT_UPDATE MFIB couldn't post MDT upd to MRIB: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-TO_MRIB_MOFRR_UPDATE MFIB couldn't post MOFRR upd to MRIB: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-4-TO_MRIB_UPDATE MFIB couldn't post update to MRIB: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-CLEAN_ALL [chars] [chars]
Explanation This is information regarding all resource cleanup.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-ERR_SHMWIN_MUTEX [chars] : [chars]
Explanation NetIO or Mfwd terminated while holding shared mem mutex. Recovery action will be taken
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-IP_ADDR_RETRY [chars] [chars]
Explanation Applying one or more IP address configs may have failed. Retry them. This is a not a problem unless it keeps showing up continuously.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-MCAST_DISABLED [chars] [chars]
Explanation Most likely mfwd restarted and while it was down mcast was disabled. The other possibility is that mfwd restarted while disabling mcast. In either case, when mfwd comes up, it will find that mcast is already disabled. Hence it will log this message and exit normally.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-MFIB_RESET [chars] : [chars]
Explanation Got notification that the MFIB has been reset. Clear MFIB and restart.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-MRIB_UPDATE_RETRY [chars] [chars]
Explanation Processing one or more updates may have failed. Retry the updates. This is a not a problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-PER_PREFIX [chars] [chars]
Explanation Error while enabling/disabling per route accounting for a route occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-PER_PREFIX_GLACIAL [chars] [chars]
Explanation Error while enabling/disabling per route accounting for a route occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-ROUTE_UPDATE_FAIL [chars] Restarting to recover.
Explanation Failure to commit at least one route after retrying for the maximum number of times occurred. In this case, mfwd will restart in an attempt to recover. This is not an error. It just indicates that mfwd is restarting to recover from possible stale route problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-TABLE_PER_PREFIX Cannot [chars] per prefix accounting for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route accounting in a table occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-TABLE_PER_PREFIX_GLACIAL Cannot [chars] per prefix accounting for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route accounting in a table occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-TABLE_ROUTE_RATE Cannot [chars] rate for routes for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route rate in a table occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-TABLE_ROUTE_RATE_GLACIAL Cannot [chars] rate for routes for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route rate in a table occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MFWD-5-UPGRADE_AFFECT_TRAFFIC [chars] [chars]
Explanation Most likely some one tried to upgrade/downgrade mfwd while you were not connected to NetIO. In this case, the upgrade will wipe out all MFIB and traffic will be disrupted
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MLIB_DEBUG Messages
Error Message%ROUTING-IPV4_MLIB_DEBUG-3-ERR [chars]
Explanation This is a catch all error message. It usually means an uncorrected problem.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB_DEBUG-3-INIT_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal error occurred. MLIB debug library initialization failed.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB_DEBUG-6-TERM_ERR [chars] [dec] [chars] [dec] [chars]
Explanation Internal non-serious error occurred. MLIB debug library termination failed occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_MLIB Messages
Error Message%ROUTING-IPV4_MLIB-3-DATAPATH_CONTROL im_caps_datapath_control error in function [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-DELETE_FAIL Delete Failed for ([chars] [chars]/[dec]) from [chars] table [chars]
Explanation Internal error occurred. Deleting an entry from ingress or egress failed.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-EVENT_CONN_MGR Cannot open event connection manager: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-EVENT_MGR Cannot create event manager: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-SHMWIN_ERR [chars] [chars]: [chars]
Explanation Error while doing shmwin operation occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-3-STATE_ERR [chars] [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-5-PER_PREFIX [chars] [chars]
Explanation Error while enabling/disabling per route accounting for a route occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-5-PER_PREFIX_GLACIAL [chars] [chars]
Explanation Error while enabling/disabling per route accounting for a route occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-5-SVD [chars]
Explanation Error while enabling/disabling per route accounting in a table occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_MLIB-5-TABLE_PER_PREFIX Cannot [chars] per prefix accounting for table [chars]. [chars] [chars]
Explanation Error while enabling/disabling per route accounting in a table occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV4_PIM Messages
Error Message%ROUTING-IPV4_PIM-3-ACL_GETLIST_ERR Cannot get ACL for [chars] [chars]: ([dec]) [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ACL_REG_ERR Failed to register callback for acl [chars]: ([dec]) [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ACTIVE_GRANGE_ERR [chars] Invalid state - active grange in mrib [chars]/[dec] RP - [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-AIPC_ERROR Fatal AIPC error: - ([chars])
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-BGP_ENS_ERROR PIM BGP communication [chars], [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-CONTEXT_CREATE Failed to create PIM context for vrf [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-CONTEXT_INIT [chars] [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-CONTEXT_REGISTRATION Ital init failed [dec]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_CHKPT_REGISTER [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_CHUNK_CREATE [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_DEBUG_REGISTER [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_ASYNC_ATTACH [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_ASYNC_SEND Error sending async message to [chars] thread during [chars] with pulse code [dec]: error equals [dec]([chars])
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_CONN_CREATE [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_CONN_EVM_HANDLER [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_CONN_NOTIFY [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_CONN_OPEN [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_CONN_SETRETRY [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_EVENT_INIT [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_EVM_MESSAGE_ATTACH [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_BATCH_STATE [chars] Invalid state for IM state registration batch on [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_BULK Failed to [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_CAPS_ADD Interface Manager error - [chars] [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_CAPS_DATAPATH_CONTROL Interface Manager error - [chars] [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_INTERFACE_CREATE [chars] Interface Manager error - [chars] [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_IM_INTERFACE_DELETE [chars] Interface Manager error - [chars] [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_INIT [chars]%s : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_LIST [chars] List error : [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_LTRACE_INIT ltrace_init failed for '[chars]': [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MAX_PATH [chars] RIB max path exceeded for [chars], total paths: [dec], reset to maximum
Explanation A software error has occurred while trying to read out the checkpointed rpf data. PIM rpf info may be incorrect.
Recommended Action Check show pim rpf output for correctness Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MEM_ALLOC [chars] for [chars] [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MGD_TIMER_GET_ROOT [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MGD_TIMER_NEW [chars]%s : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MRIB_BIND [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MRIB_CONN MRIB connection error - [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_MRIB_UNBIND [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_NSF_INIT [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_PAK_CLIENT_CONN [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSDB_BAG_DECODE Error in bag decoding : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSDB_BAG_FREE_INDIRECTIONS Error in bag free : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSDB_DATALIST_FREE Error in datalist free : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSDB_DATALIST_NEXT Error in datalist next : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSMGR_READY [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_SYSMGR_REGISTER [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_WDSYSMON_EVENT Received an invalid event from WDSysmon
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-ERR_WDSYSMON_REGISTER [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-GEN_ERR [chars] Error - [chars] [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-IDB_HANDLE_MISMATCH_ERR Interface handle mismatch, handle in IM update [chars]:[hex], handle in PIM [chars]:[hex]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-IDB_INIT [chars]%s : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-IDB_VRF_BIND [chars] Interface [chars] belongs to context [chars]. Please clear the config error
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-INTF_FWD_REF_ERR [chars] Interface Forward Reference Store error - [chars]: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-INVALID_MHOST_DEFAULT [chars] Interface [chars] should not be configured as mhost default
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-MDR_INIT [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-MULTICAST_IGP_MTR [chars] [chars] multicast topology incorrect sysdb deletes received, refcount [dec]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-MULTICAST_INTACT [chars]%s multicast intact incorrect sysdb deletes received, refcount [dec]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-NET_ERR [chars]%s : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-OOR_COUNTER_ERR [chars] OOR [chars] counter has turned negative: [dec]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-PROTOCOL_ERR [chars]%s - [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-RP_INIT [chars]%s : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-SRC_UPDATE_ERR Error in [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-v6_DATA_MDT_INVALID_GRANGE Invalid grange
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-v6_DATA_MDT_INVALID_VRF Invalid vrf-id ([hex])
Explanation Invalid vrf-id received from pim/pim6 occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-v6_DATA_MDT_NO_CORE Data MDT core routes missing ([chars], [chars])
Explanation Data for MDT core routes is missing.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-3-v6_DATA_MDT_NO_MEM Could not allocate memory for message header
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-CFG_WARNING [chars]%s
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-ITAL_CREATE_WARN ITAL create notification for table with pending cleanup old vrf_id [hex], table_id [hex] : route count [dec] : new vrf_id [hex] table_id [hex]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-MIB_GROUP_TREE_ERR [chars] Failed to [chars] [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-MYADDR_DB_ERR [chars] Failed operation: [chars] for [chars] - [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOM_STATE_THROTTLE Received [chars] memory depletion warning, stop creating new pim state
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOM_STATE_UNTHROTTLE Node memory back to normal, new pim states will be created
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_REGISTER_OK [chars] The number of PIM Register states ([unsigned int]) is now below the maximum. Normal PIM Register handling will resume.
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_REGISTER_THRESHOLD_WARN [chars] The threshold number of PIM Register states ([unsigned int]) has been reached. Register state creation will soon be throttled. Configure a higher maximum or take steps to reduce Register state.
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_REGISTER_WARN [chars] The maximum number of PIM Register states ([unsigned int]) has been reached. Register state creation will be throttled. Configure a higher maximum or take steps to reduce Register state.
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_ROUTES_OK [chars] The number of PIM routes ([unsigned int]) and route-interfaces ([unsigned int]) are now below the maximum. Normal PIM route handling will resume.
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_ROUTES_THRESHOLD_WARN [chars] The threshold number of PIM routes ([unsigned int]) or route-interfaces ([unsigned int]) has been reached. Route creation will soon be throttled. Configure a higher maximum or take steps to reduce multicast state.
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-OOR_ROUTES_WARN [chars] The maximum number of PIM routes ([unsigned int]) or route-interfaces ([unsigned int]) has been reached. Route creation will be throttled. Configure a higher maximum or take steps to reduce multicast state.
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-4-RANGE_INIT [chars]%s in [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4_PIM-5-INTCHG [chars] PIM interface [chars] [chars]
Explanation This is a PIM interface state change message.
Recommended Action No action is required.
Error Message%ROUTING-IPV4_PIM-5-INVALID_JP [chars] PIM invalid (*, [chars]) J/P message from [chars] with RP address [chars]
Explanation This is a PIM invalid J/P notification.
Recommended Action No action is required.
Error Message%ROUTING-IPV4_PIM-5-INVALID_REGISTER [chars] PIM invalid register message from [chars] for group [chars] RP address [chars], [chars]
Explanation This is a PIM invalid register message notification.
Recommended Action No action is required.
Error Message%ROUTING-IPV4_PIM-5-NBRCHG [chars] PIM neighbor [chars] [chars] on [chars] [chars]
Explanation This is a PIM neighbor state change message.
Recommended Action No action is required.
Error Message%ROUTING-IPV4_PIM-5-RP_MAPPING_CHG [chars] PIM [chars] for [chars]/[dec] RP [chars] proto [chars]
Explanation PIM RP mapping change notification.
Recommended Action No action is required.
IPV4MC_STATIC Messages
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_CERR_V [dec] [chars] [chars]
Explanation Internal error occurred. Failure to register with CERR_V subsystem occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_DEBUG_INIT [chars] [dec] [chars]
Explanation Internal error occurred. Static Mcast debug library initialization failed.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_EVENT_INIT Cannot Initialize sigevent structure: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_EVM_CREATE Event Manager creation Failed: [chars]
Explanation Internal error occurred. Failure while creating event manager occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_IDB_INIT Cannot initialize IDB list: [chars]
Explanation Internal error occurred. Failure to create initialize IDB list occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_INTF Error [chars] [chars]
Explanation Internal error occurred. Error while doing IM or IDB stuff occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_MRIB [chars]: [chars]
Explanation Internal error occurred. Error while doing MRIB API occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_ROUTE [dec]: [chars] ([chars],[chars]/[dec])
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_TIMER_ASYNC_CODE Cannot obtain pulse code for the timer: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_TIMER_CREATE_LEAF Cannot create timer leaf: [chars]
Explanation Internal error occurred. Failure to create managed timer leaf occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_TIMER_INIT Cannot create managed timer: [chars]
Explanation Internal error occurred. Failure to create managed timer occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV4MC_STATIC-7-ERR_TOPOLOGY_INIT Cannot create static topology
Explanation Internal error occurred. Failure to create managed timer leaf occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
IPV6_FIB Messages
Error Message%ROUTING-IPV6_FIB-2-RIBREJECT Rejecting RIB Update for [chars]/[dec] status [dec]
Explanation A route update from the RIB was rejected.
Recommended Action Try repopulating the missing route. If not recovered, it will lead to forwarding inconsistencies. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-IPV6_FIB-7-PFIFAIL PFI-IFH Server Error for [hex] status equals ([dec])
Explanation Failure to talk to the PFI-IFH process occurred.
Recommended Action This is an informational message. PFI-IFH process does not have the information about the interface-handle at this very moment. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ISIS_IP_ORA Messages
Error Message%ROUTING-ISIS_IP_ORA-3-INSTBUILD Failed to build policy operation '[chars]' for attribute '[chars]'.[chars]%s ([hex])
Explanation There was an internal error in the routing policy library and as a result routing policy may not be applied correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ISIS Messages
Error Message%ROUTING-ISIS-2-DUPSYSTEM Possible duplicate system ID [chars] detected; Duplicate LSP received from host [chars], on interface [chars]
Explanation The router with the system ID SYSTEM-ID has transmitted too many LSPs in brief period of time, which could indicate constant LSP reflooding caused by a duplicate system ID.
Recommended Action Check the configuration of other routers in the area for duplicate IDs.
Error Message%ROUTING-ISIS-3-BFD_SESSION_CREATE_FAIL Can't create BFD session to [chars]: [chars] ([hex])
Explanation IS-IS failed to create a session with the BFD server. Creation will be reattempted on the next received IIH. Depending on the neighbor's support of BFD this may cause adjacencies to go down.
Recommended Action This failure may due to lack of resources. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. If the failure is not due to a lack of resources seek support. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-DBG_INIT_FAILED IS-IS failed to initialize its debug resources and will abort
Explanation IS-IS failed to initialize one of its debug services. The process cannot continue without its debug services and so will have aborted, but should have been restarted rapidly afterwards. This message will have been preceded by another one providing more precise details of the failure. The problem may be due to low memory resources and the detail of the preceding error message provides an indication of whether this is the case.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-3-ERR_ATOMIC_RING_OP Error [chars]: [chars]: '[chars]', [hex]
Explanation An unexpected error occurred while performing an atomic ring operation. This may be due to resource starvation or an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_BAD_SOCKET_ADDR_LENGTH Bad socket address length ([unsigned int], should be [unsigned int] or [unsigned int]) in packet 0x[pointer]
Explanation A packet which IS-IS has received from its network socket contains a socket address with an invalid length. This is an internal error which indicates that the packet has been corrupted after being received by the local router but before being received by IS-IS. The problematic packet has been dropped. If this is an occasional problem then IS-IS should be able to continue operating normally when the packet is resent. If the message recurs, then IS-IS may start to operate incorrectly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_BAG_ENCODE Failed to encode data for [chars] for external data manager (Reason: [chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. An attempt to encode data for this has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_BAG_REGISTER Failed to register bag structures with bag server (Reason: [chars])
Explanation The process could not register the data structures used by IS-IS statistics and management agents.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_CLOCKTIME Error retrieving or setting the time of the [chars] clock: [chars] ([hex])
Explanation An unexpected error occurred while retrieving the time of a System Clock. This may be due to resource starvation or an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_CONFIG_TO_TE Error during communication of [chars] information to TE processes: [chars]
Explanation IS-IS was unable to inform the TE processes of its configuration or basic operational state.
Recommended Action Restart the IS-IS process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_DLIST_ADD Failed to add an entry to an external data manager data list for [chars] (Reason: [chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_DLIST_CREATE Failed to create external data manager data list for [chars] (Reason: [chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the datalist to be returned has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_DLIST_SET_MORE_FLAG Failed to set the 'more data' flag on a returned [chars] data list: error [hex] ([chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to set the 'more data' flag to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_EDM_FNS_INIT [chars] management function initialization failed: [hex], '[chars]'
Explanation The IS-IS process failed to initialize the handler functions for external data management. As a result, show and clear commands will not function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_EDM_REGISTER [chars] SysDB registration failed: [hex], '[chars]'
Explanation The process could not register with SysDB for management of the data used by IS-IS statistics and management agents. As a result, show and clear commands will not function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_GET_JOB_ID Failed system manager call to get IS-IS job_id: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to get its job_id. It's an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_GET_NODE_STATE Failed system manager call to get the node state information: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to get the node related state information. It's an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_GET_TUPLE Failed system manager call to retrieve the process tag name: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to retrieve its tag name during process initialization. It's an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_IFINDEX Error [chars]: '[chars]', [hex]
Explanation An unexpected error occurred while performing an SNMP ifindex operation. This may be due to resource starvation or an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_LIST_ADD Failed to add an entry to an external data manager list for [chars] (Reason: [chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_LIST_CREATE Failed to create external data manager list for [chars] (Reason: [chars])
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the list to be returned has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_LOCKING_FAIL Unexpected error '[chars]' trying to [chars] the [chars]
Explanation An unexpected error occurred while trying to lock or unlock an IS-IS resource. This implies an internal programming error.
Recommended Action Consider restarting the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_LTRACE_BUFFER Error [chars] trace buffer '[chars]': [chars] ([hex])
Explanation An unexpected error occurred while accessing a tracing buffer. This may be due to resource starvation or an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_MEMPOOL_CREATE Failed to create the [chars]
Explanation IS-IS failed to create a memory pool. IS-IS cannot operate without this resource and will abort. The most likely cause is a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Restart IS-IS.
Error Message%ROUTING-ISIS-3-ERR_NODE_STATE_CHANGE Failed to register with system manager to get node state change notification: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to register to get node state change notification. It is an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_PAK_CLIENT_ACCESS Error [chars] a packet buffer (0x[pointer]): [chars]
Explanation IS-IS encountered an error while accessing a packet buffer. The relevant packet has been ignored. The message describes the nature of the error. If the problem is transient then IS-IS will recover. The error may be due to a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting IS-IS.
Error Message%ROUTING-ISIS-3-ERR_PAK_CLIENT_CONN Error [chars] the managed connection to the packet server: [chars] ([dec])
Explanation IS-IS encountered an error while trying to set up a managed connection to the Packet Server. This is a serious error as IS-IS requires Packet I/O services to be able to form adjacencies, and the IS-IS process will shut itself down in response. This may be due to a low memory condition but is more likely to be a programming error. The error string and error code provide more information about the cause.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-3-ERR_PAK_CLIENT_GET_BUFFER Error obtaining a packet buffer of length [unsigned int]
Explanation IS-IS encountered an error while attempting to acquire a packet buffer to use to send a packet. The relevant packet has been dropped. The problem may be due to resource starvation. IS-IS will recover when sufficient resources become available.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-3-ERR_PROC_AVAILABLE Failed system manager call to indicate that IS-IS has completed initialization: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to indicate that it has completed all its initialization and is now completely online. It is an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_PROC_READY Failed system manager call to indicate that IS-IS is ready: [hex], '[chars]'
Explanation IS-IS failed on a call to system manager to indicate that it is ready to proceed. It is an internal fatal error. IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_RECV_BAD_TE_MSG Received [chars] in the [chars] message from TE
Explanation The process has received a TE message with invalid contents. As a result, the TE message is ignored and TE tunnel may not come up.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_RECV_PAK Error receiving packet: [chars]
Explanation An internal error has occurred receiving the packet. This is most likely due to some failure in a system service or a limited resource being exhausted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_RIB_BATCH_BUFFER Unexpected error [chars] batch of [chars] RIB updates ([dec])
Explanation IS-IS encountered an unexpected error while defining a batch of updates to be sent to the RIB. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_RIB_PATH Unexpected error installing a path to [chars] in the [chars] RIB ([dec])
Explanation IS-IS was unable to install a path to the specified network in the specified RIB because the RIB rejected the request. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_SEND_PAK Error sending IS-IS packet: [chars]
Explanation The process encountered an error while sending the IS-IS packet.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_ACCESS Error [chars] [chars] SysDB item ([chars]): [hex], '[chars]'
Explanation An unexpected error occurred while accessing the specified SysDB item. This may be due to resource starvation or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_APPLY_BATCH Error in SysDB batch: [chars]: [chars] ([hex])
Explanation An unexpected error occurred while checking for more SysDB batches after receiving request to shutdown the process. This may be due to resource starvation or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_CONNECT [chars] SysDB connection could not be established at the path [chars]: [hex], '[chars]'
Explanation IS-IS failed to bind to SysDB while opening a connection to it.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_DATALIST Error [chars] SysDB datalist containing [chars]: [chars] ([hex])
Explanation An unexpected error occurred while listing the contents of a directory in SysDB. This may be due to resource starvation or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_REG_NOTIFY Failed to register for SysDB notifications on path [chars] ([chars])
Explanation IS-IS failed to register for notification of changes on the displayed SysDB path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_REG_VERIFY Failed to [chars] ([chars])
Explanation IS-IS failed to register for verification of changes to its configuration data.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-ERR_SYSDB_STRING_CODING Error [chars] a '[chars]' string: [hex], '[chars]'
Explanation IS-IS failed to encode or decode a string using the SysDB encoding. Aa result IS-IS will not be able to complete the operation it was performing which it encountered the error. The message describes the string which was being encoded or decoded and this should indicate the nature of the operation which was being performed.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-3-ERR_TAG_NAME Error retrieving process tag name: [hex], '[chars]'
Explanation An IS-IS process failed to retrieve its process tag name during process initialization. This is a fatal error and the IS-IS process will abort.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_THREAD_CREATE Error starting [chars] thread: [dec]
Explanation IS-IS failed to create a thread essential to its operation. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_THREAD_KEY_CREATE Error creating '[chars]' registry for thread specific value: [chars]
Explanation IS-IS failed to create a key to store thread specific values such as the name of a thread. This may be due to a low memory condition but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-3-ERR_THREAD_ONCE Error performing a once per thread lifetime operation to initialize [chars]: [chars]
Explanation IS-IS failed to initialize the specified resource. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-ERR_THREAD_SET_SPECIFIC Error associating [chars] with thread: [chars]
Explanation IS-IS failed to associated the specified per-thread resource with the thread. This may be due to a low memory condition but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-3-ERR_VRFN_FNS_INIT [chars] verification function initialization failed: [hex], '[chars]'
Explanation The IS-IS process failed to initialize the handler functions for verification of changes to its configuration data.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The IS-IS process must be restarted before it can function correctly.
Error Message%ROUTING-ISIS-3-EVENT_CONN_CREATE_FAIL Error creating '[chars]' connection: [chars]
Explanation IS-IS failed to create a connection to an essential service during initialization. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-EVQ_DEQUEUE_FAIL Failed to remove [chars] from the [chars] queue: [hex], '[chars]'
Explanation An unexpected error occurred while removing the specified object from the specified queue.
Recommended Action Consider restarting the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-EVQ_ENQUEUE_FAIL Failed to enqueue [chars] on the [chars] queue: [hex], '[chars]'
Explanation An unexpected error occurred while enqueueing the specified object on the specified queue.
Recommended Action This failure is most probably due to limited memory. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-3-EVQ_SIZE_FAIL Failed to retrieve the size of the [chars] queue: [hex], '[chars]'
Explanation An unexpected error occurred while retrieving the size of the specified queue. As a result IS-IS's internal state may be inconsistent. This indicates an internal programming error.
Recommended Action Consider restarting the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-IM_CB_REG_FAIL Failed to register handler for IM [chars] events: [hex], '[chars]'
Explanation IS-IS failed to register a handler for IM events relating to the specified protocol. This may be due to a low-memory condition but may also be due to internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-3-IM_CONN_TO_COID_FAIL Unexpected error retrieving connection ID from IMD connection context: [hex], '[chars]'
Explanation IS-IS failed to retrieve a connection ID from the IMD connection context. This may be due to a low-memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-3-INTF_SET_ADD_FAIL Failed to add [chars] to the set of [chars]: [hex], '[chars]'
Explanation An unexpected error occurred while trying to add an interface to the specified collection of interfaces. This is most likely to be due to a low memory condition, but may be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-3-IPV6_LAS Error [chars] IPv6 local address consumer service: [hex], '[chars]'
Explanation An unexpected error occurred while IS-IS was using the IPv6 Local Address Consumer Service.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-PDU_INSUFFICIENT_SPACE Unable to [chars] due to insufficient space in outgoing PDU
Explanation The process was unable to add information to an outgoing PDU. This is most likely an MTU issue.
Recommended Action Check the MTUs for the interfaces over which IS-IS is running.
Error Message%ROUTING-ISIS-3-RSI_C_API_FAIL RSI [chars] failure, [hex], '[chars]'
Explanation The IS-IS process failed to initialize the RSI service for the specified error reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-RSI_C_LIB_INIT RSI init failure, [hex], '[chars]'
Explanation The IS-IS process failed to initialize the RSI service for the specified error reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-TIMESTAMP Operation '[chars]' failed during packet timestamping: [hex] ([chars])
Explanation An operation failed during timestamp processing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-3-TRIGGER Operation '[chars]' failed during log trigger processing : [chars]
Explanation An operation failed during log trigger processing. This is not critical and IS-IS functionality should be unaffected.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-AREALOST Too many IS-IS areas--cannot route to area [chars]
Explanation Too many IS-IS areas cannot route to area AREA-ADDRESS. This system has exceeded the limit of three learned area addresses. The largest address AREA-ADDRESS has been dropped from the list of active areas.
Recommended Action Reduce the number of area addresses in the routing area.
Error Message%ROUTING-ISIS-4-BFD_BIND_FAIL Attempt to connect to the BFD server failed: [chars] ([hex])
Explanation IS-IS failed to connect to the BFD server. The connection will be retried.
Recommended Action This failure may be due to lack of resources. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-BFD_CREATE_FAIL Attempt to create [dec] BFD session[chars] failed: [chars] ([hex])
Explanation IS-IS failed to create one or more sessions with the BFD server. The connection to the server will be reset in an attempt to recover from the error.
Recommended Action This failure may due to lack of resources. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. If the failure is not due to a lack of resources seek support. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-BFD_DELETE_FAIL Attempt to delete [dec] BFD session[chars] failed: [chars] ([hex])
Explanation IS-IS failed to delete one or more sessions with the BFD server. The connection to the server will be reset in an attempt to recover from the error.
Recommended Action This failure may due to lack of resources. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. If the failure is not due to a lack of resources seek support. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-BFD_DELETE_UNCONFIG_FAIL Attempt to admin shutdown [unsigned int] BFD session[chars] as a result of deconfiguration failed: [chars] ([hex])
Explanation IS-IS failed to admin shutdown one or more sessions with the BFD server. The connection to the server will be reset in an attempt to recover from the error.
Recommended Action This failure may due to lack of resources. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. If the failure is not due to a lack of resources seek support. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-BFD_SESSION_NOT_FOUND Failed to locate BFD session over [chars] to [chars] for an adjacency.
Explanation IS-IS failed to locate a BFD session for a given adjacency. If necessary IS-IS will reconnect to the server to correct.
Recommended Action None.
Error Message%ROUTING-ISIS-4-CERR_REG_FAIL [chars]
Explanation This system was unable to register the CERR DLL. This is probably due to a faulty installation.
Recommended Action Be sure the libisis_error.dll is properly installed.
Error Message%ROUTING-ISIS-4-DBG_REGISTER_FAILED Error registering for IS-IS debug events: [hex], '[chars]'
Explanation IS-IS failed to register with the debug module for printing messages.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-DUPLICATE_MT_CAPABILITY Level [unsigned int] LSP [chars] contains multiple ([unsigned int]) MT capability items for [chars].[chars]%s
Explanation The specified LSP contains multiple items advertising the same MT capability. This is an indication that the router which owns the LSP has generated its LSP incorrectly. If the MT capability items contain conflicting overload state then the message indicates this and IOS-XR determines that the router which issued the LSP is overloaded. If the MT capability items contain conflicting attached state then the message indicates this and IOS-XR determines that the router which issued the LSP is not attached.
Recommended Action Identify the source of the offending packet and correct it.
Error Message%ROUTING-ISIS-4-DUPSYSTEM Possible duplicate system ID [chars] detected
Explanation The router with the system ID SYSTEM-ID has transmitted too many LSPs in brief period of time, which could indicate constant LSP reflooding caused by a duplicate system ID.
Recommended Action Check the configuration of other routers in the area for duplicate IDs.
Error Message%ROUTING-ISIS-4-ERR_ACL Unexpected error while [chars] [chars] ACL [chars]: [hex], '[chars]'
Explanation IS-IS encountered the specified unexpected error while performing the specified operation on the specified access-list. As a result IS-IS's operation will not correctly reflect the contents of the ACL. This may be due to a low-memory condition but may also be due to internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-4-ERR_ADVMASK Error adding IS-IS to advertising mask of [chars] ([chars]): [hex], '[chars]'
Explanation IS-IS failed to add itself to the advertising mask for the specified route and topology, that route corresponding to a connected route on an interface over which IS-IS is running. This means that any protocols which redistribute IS-IS into themselves will not receive the specified route. The problem is most likely to be caused by a failure by ipv4-io or ipv6-io to install the route at all, although it could also be due to low memory conditions.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-ERR_BAD_CIRC_TYPE Bad circuit type ([dec]) from [chars]
Explanation Bad circuit type (CIRCUIT-TYPE) from SOURCE_IF occurred. This system received an IS-IS hello with a header reporting an invalid circuit type of CIRCUIT-TYPE. This is the result of a mal-formed packet rather than a configuration error. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_HDR_LENGTH The packet header length [unsigned int] is invalid for a(n) [chars], (should be [unsigned int]) from [chars]
Explanation The packet header length (HDRLEN) is invalid for a(n) PDUTYPE, (should be EXPECTED) from SOURCE_IF This system received a PDUTYPE packet from SOURCE_IF claiming a header length of ACTUAL, rather than EXPECTED. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_ID_LENGTH Bad system ID length ([unsigned int], should be 0 or [unsigned int]) from [chars]
Explanation Bad system ID length (ID-LENGTH, should be 0 or EXPECTED-LENGTH) from SOURCE_IF. This system received a pdu reporting an invalid system ID length of ID-LENGTH. This system only accepts values of 0 and 6 (both indicate 6). The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_MAX_AREA_ADDR Bad max area addresses ([dec], should be 0 or [dec]) from [chars]
Explanation Bad max area addresses (MAX-AREA-ADDRESSES, should be 0 or EXPECTED-MAX) from SNPA (INTERFACE-NAME). This system received a pdu reporting an invalid number of configurable area addresses. This system only accepts values of 0 and 3 (both indicate 3). The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_PAK_LENGTH The length ([unsigned int]) reported in the packet buffer is greater than the maximum packet length that IS-IS can receive ([unsigned int])
Explanation IS-IS has received a packet which is larger than its internal buffers can handle. The packet has been ignored.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Consider reducing the relevant interface's MTU.
Error Message%ROUTING-ISIS-4-ERR_BAD_PDU_FORMAT [chars] received from [chars] contains a format error: [chars]
Explanation IS-IS has received a PDU containing a format error. This indicates that the system which built the PDU is not conforming to the protocol specification. In most cases this is the neighbor, but in the case of LSPs it is the system which generated the LSP. The message contains the type of the PDU, the interface it was received over (and, in the case of a LAN interface, the SNPA), and a description of the format error. IS-IS will not use any of the information contained in this PDU. In the case of an LSP, IS-IS will not flood the LSP to neighbors.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_PDU_LENGTH The length ([unsigned int]) reported in the [chars] header is greater than the packet length ([unsigned int]) from [chars]
Explanation The length (PDU_LENGTH) reported in the PDUTYPE header is greater than packet length (PKTLEN) from SOURCE_IF This system received an IS-IS packet that was LENGTH bytes long, which is shorter than the required header length for a PDUTYPE packet. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_PDU_VERSION The PDU version reported in the IS-IS header is invalid ([unsigned int], should be [unsigned int]) from [chars]
Explanation The PDU version reported in the IS-IS header is invalid (VERSION, should be EXPECTED) from SNPA (INTERFACE-NAME) This system received a protocol packet bearing an invalid VERSION in the header. The router originating the packet is either placing the wrong protocol version number in the packet, or else it is running an incompatible version of the IS-IS protocol.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BAD_VERSION Bad protocol version ([dec], should be [dec]) from [chars]
Explanation Bad protocol version (VERSION, should be EXPECTED-VERSION) from SOURCE_IF. This system received a pdu with an invalid protocol version of VERSION instead of EXPECTED-VERSION. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_BGP_CONVERGE Overload bit not set due to failure in registering for BGP convergence: [hex], '[chars]'
Explanation IS-IS is configured to set the overload bit in its LSPs upon startup and to wait for BGP to converge before resetting the overload bit, but an error has occurred while registering for notification of BGP convergence. As a result, the overload bit will not have been set upon startup. This may be due to a low-memory condition but may also be due to internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-ERR_BGP_UNREG_NOTIFY Error unregistering for BGP convergence notification: [hex], '[chars]'
Explanation IS-IS failed to unregister for notification of BGP convergence. The error will not affect IS-IS operation but does indicate unexpected system behavior.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_EVM_ATT_FAIL Failed to register a handler for '[chars]' messages: [chars]
Explanation IS-IS failed to register a handler for the specified class of event. This is an initialization error and implies that IS-IS will not be able to operate correctly. The IS-IS process must be restarted in order to recover. The cause may be a resource starvation problem but is most likely to be an internal programming error. The error message should give more details.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Restart the IS-IS process.
Error Message%ROUTING-ISIS-4-ERR_EVM_CBACK_ATT_FAIL Failed to register a [chars] callback handler: [chars]
Explanation IS-IS failed to register a callback handler due to the error. This is an initialization error and implies that the function in IS-IS will not be able to operate correctly. The IS-IS process must be restarted in order to recover.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Restart the IS-IS process.
Error Message%ROUTING-ISIS-4-ERR_EVM_CRE_FAIL Failed to create [chars] Event Manager: [chars]
Explanation IS-IS failed to create an Event Manager to receive events in the specified thread. This is most likely to be caused by a resource starvation problem, but may also be due to an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-ERR_EVM_SEND_FAIL Failed to send '[chars]' to '[chars]': [chars]
Explanation IS-IS failed to send the specified message. The cause may be a resource starvation problem but is most likely to be an internal programming error. The error message should give more details.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Restart the IS-IS process.
Error Message%ROUTING-ISIS-4-ERR_GET_RESPAWN_COUNT Failed system manager call to fetch respawn, assuming respawned: [hex], '[chars]'
Explanation A call to system manager to obtain the process respawn count failed. This is a recoverable error, and the count will be assumed to be 1.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-4-ERR_LSP_DB_CORRUPT L[unsigned int] LSP database checksum verification failed for LSP [chars]. IS-IS will restart itself
Explanation A corrupt LSP was found during a periodic check of the sanity of the specified level's LSP database. When it encounters this condition the IS-IS process restarts itself to recover.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_LSP_INPUT_Q_OVERFLOW LSP input queue overflow: [unsigned int] total drops; [unsigned int] LSP drops, [unsigned int] SNP drops
Explanation An incoming LSP or SNP pdu was dropped because the input queue was full
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-ERR_MEMPOOL_NOMEM Failed to allocate [unsigned int] bytes from '[chars]'
Explanation IS-IS failed to allocate memory from the specified pool.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-ERR_MIN_PDU_LENGTH The length ([unsigned int]) described in the [chars] header is smaller than the minimum ([unsigned int]) from [chars]
Explanation The length (PDU_LENGTH) described in the PDUTYPE header is smaller than the minimum (MINLEN) from SOURCE_IF This system received an IS-IS packet that was LENGTH bytes long, which is shorter than the required header length for a PDUTYPE packet. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_MIN_PKT_LENGTH The length ([unsigned int]) of the [chars] received from [chars] is smaller than the minimum ([unsigned int])
Explanation The length (PKTLEN) of the PDUTYPE received from the interface SOURCE is smaller than the minimum (MINLEN) This system received an IS-IS packet that was LENGTH bytes long, which is shorter than the required header length for a PDUTYPE packet. The packet has been ignored.
Recommended Action Identify the source of the offending packet and correct it. If the message recurs 'debug isis packet-errors detail' may be used to provide a dump of the problematic PDU.
Error Message%ROUTING-ISIS-4-ERR_MSG_CHAN_GLOBAL Error changing a local message channel setting to [chars]: [chars] ([dec])
Explanation IS-IS failed to convert a local connection channel to a global connection channel. This could be the result of a problem with the channel.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_MSG_GET_SCOID Error retrieving client's connection ID to the [chars] channel: [chars] ([dec])
Explanation IS-IS failed to retrieve its local connection ID for a client attached to the specified channel. This is an internal programming error.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_MSG_REPLY Error replying to the client [chars]: [chars] ([dec])
Explanation IS-IS failed to reply to its client through message channel. This could be a result of channel down or resource allocation failure.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Restart the IS-IS process.
Error Message%ROUTING-ISIS-4-ERR_PCL Unexpected error while [chars]: [hex], '[chars]'
Explanation IS-IS encountered an unexpected error while performing the specified using the Route Policy client library. As a result information may be omitted from the local system's LSPs. This may be due to a low-memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-4-ERR_REG_SHUTDOWN_NOTIFY Failed system manager call to register for shutdown notification: [hex], '[chars]'
Explanation A call to system manager to register for shutdown notification failed. This is a recoverable error in that shutdown actions are not critical.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-4-ERR_RIB Unexpected error while [chars] the [chars] RIB: [hex], '[chars]'
Explanation IS-IS encountered an unexpected error while performing the specified RIB operation. This may be a resource starvation problem but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Restart the IS-IS process.
Error Message%ROUTING-ISIS-4-ERR_RIB_BATCH_SEND Unexpected error sending a batch of [chars] RIB updates ([dec])
Explanation IS-IS encountered an unexpected error while sending a batch of RIB updates to the RIB. This may be a resource starvation problem, or a problem with IS-IS's connection to the RIB, or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Restart the IS-IS process.
Error Message%ROUTING-ISIS-4-ERR_RIB_CONN_SETRETRY Error setting the RIB linear retry period: [hex] '[chars]'
Explanation IS-IS failed to set the linear retry period for connecting to the RIB. This error will not affect IS-IS operation but does indicate an unexpected result.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_RIB_LIB Unexpected error while [chars]: [hex], '[chars]'
Explanation IS-IS encountered an unexpected error while performing the specified operation using the RIB client library. This may be a resource starvation problem but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-4-ERR_RIB_NOTIFICATION Received an unexpected notification with code [unsigned int]
Explanation IS-IS received an unexpected RIB notification pulse and will ignore it.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-4-ERR_RIB_PATH_NOMEM Insufficient memory while installing a path to [chars] in the [chars] RIB
Explanation IS-IS was unable to install a path to the specified network in the RIB because the RIB encountered a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-ERR_SHOW_PROTO_REG Error registering show protocol information: [hex], '[chars]'
Explanation IS-IS failed to register for notification of changes on the displayed SysDB path. The error will not affect IS-IS operation but does indicate unexpected system behavior.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_SYSDB_DISCONNECT Error disconnecting [chars] SysDB connection: [hex], '[chars]'
Explanation IS-IS failed to disconnect from SysDB. The error will not affect IS-IS operation but does indicate that a programming error has occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_SYSDB_UNREG_NOTIFY Error unregistering for SysDB notification: [hex], '[chars]'
Explanation IS-IS failed to unregister for notification of changes on the displayed SysDB path. The error will not affect IS-IS operation but does indicate unexpected system behavior.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_THREAD_DESTROY Error destroying [chars] thread: [dec]
Explanation IS-IS failed to destroy a thread. This is an internal error. If the error occurred while unconfiguring IS-IS then it may be necessary to forcefully terminate the IS-IS process. If the error occurred during normal operation then it may be necessary to restart the IS-IS process to recover.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-ERR_THREAD_SET_NAME Error setting name of thread [dec] to [chars]: [chars] ([hex])
Explanation An unexpected error occurred while setting a thread name. This may be due to resource starvation or an internal programming error. This is not a fatal error as the name is only used for debugging and error messages.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-ERR_WDSYSMON_MEM_STATE Unexpected error while [chars] for memory state changes: [chars] ([hex])
Explanation IS-IS encountered an error while registering or deregistering with WDSysMon for notifications of changes to the router's memory state. If the error occurs during registration (i.e. when the IS-IS process is initializing) then it will abort and the system may recover automatically when the IS-IS process is restarted. If the error occurs during deregistration (i.e. when the IS-IS process is shutting down) then it is harmless and may be ignored.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-EVENT_BOOL_FAIL Error [chars] the '[chars]' trigger: [hex], '[chars]'
Explanation IS-IS encountered an unexpected error using one of the infrastructure libraries. This may be due to a low memory condition but is more likely to be a programming error. The error message should provide more information about the cause.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-4-EVENT_CONN_ERROR_FAIL Error resetting '[chars]' connection: [chars]
Explanation After detecting an error with the connection to the specified service, IS-IS failed to reset that connection. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-EVENT_CONN_EVM_HANDLER_FAIL Error registering for data events on '[chars]' connection: [chars]
Explanation During initialization, IS-IS failed to register for input or output notifications for the specified service. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-EVENT_CONN_GET_FD_FAIL Error retrieving the Connection ID from the '[chars]' connection: [chars]
Explanation IS-IS failed to retrieve the file descriptor associated with the specified service. This is an internal error.
Recommended Action Consider restarting the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-EVENT_CONN_NOTIFY_FAIL Error registering for critical events on '[chars]' connection: [chars]
Explanation During initialization, IS-IS failed to register for essential notifications regarding the state of the connection for the specified service. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-EVENT_CONN_OPEN_FAIL Error opening '[chars]' connection: [chars]
Explanation IS-IS failed to open a connection to an essential service during initialization. This is an internal error. It requires a restart of the process for recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-EVQ_CRE_FAIL Failed to create the [chars] event queue: [hex], '[chars]'
Explanation An unexpected error occurred while creating an event queue during process initialization. This may be a system resource problem. As a result IS-IS will be unable to operate correctly.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-EXTRA_AREA_ADDRESSES Area address TLV length [dec] contains more than ISIS_MAX_AREA_ADDRESSES from [chars] ([chars]).
Explanation Area address TLV length TLV_LENGTH contains more than ISIS_MAX_AREA_ADDRESSES from SNPA_STRING (INTERFACE_NAME). This system received a hello or LSP containing more than the maximum number of area addresses. The additional addresses have been ignored.
Recommended Action Identify the source of the offending packet and correct it.
Error Message%ROUTING-ISIS-4-IDB_CHKPT_CLEANUP Unexpected objid [hex] for [chars] (CSCek33169) collect log and tech-support
Explanation --
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-IIH_TOO_MANY_IF_ADDRESSES [chars] has more [chars] interface addresses than can fit into a single TLV (255 bytes). Outgoing IIHs can only include the first [unsigned int] addresses.
Explanation The specified interface has more addresses than can be fitted into a single TLV (255 bytes). RFC 1195 specifies that each IIH may contain at most one IPv4 Interface Address TLV, i.e. 63 IPv4 addresses. Thus if there are more than 63 IPv4 addresses configured on the interface, then only 63 addresses are included in the IIH. If the interface has a primary address, it is always included first. The secondary addresses are added in their natural numerical order until there is no more space. If there is an IS on the LAN which does not share a subnet with any of the advertised addresses, then it will not be able to form an adjacency with this IS. This problem should not apply to IPv6 as each interface should have a single link local address.
Recommended Action Reduce the number of addresses configured on the interface so that they can all fit within a single TLV.
Error Message%ROUTING-ISIS-4-IM_ATTR_INIT Error initializing the IM attribute library: [hex] '[chars]''
Explanation IS-IS failed to initialize the IM attribute library. This error will prevent IS-IS from normal operations.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-4-IM_CAPS_UNKNOWN IM notification received for an unknown and unexpected encapsulation number: [unsigned int]
Explanation IS-IS has received an IM message referring to a encapsulation number that IS-IS does not recognized and is not able to handle. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-IM_CB_NAME_TRUNC Interface Manager context name '[chars]' length exceeds string length limit of [dec]; truncated to '[chars]'
Explanation The length of the context string used to register for Interface Manager callbacks exceeded internal limits and was truncated. If truncation results in registration contexts no longer being unique, this could cause problems with event registrations.
Recommended Action This should not happen. The condition represents an internal error.
Error Message%ROUTING-ISIS-4-INTF_ADDR_CHG_REG Error during registration for interface IP address changes: [chars]
Explanation IS-IS failed to register for notification of interface IP address changes. This is may be due to lack of resources or an internal error (the error message will indicate which). It requires a restart of the process for recovery.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-INTF_ATTR_FAIL Failure while [chars] on [chars]: [hex] '[chars]''
Explanation A call to the IM attribute library failed. This can be caused by faulty hardware, or it may indicate an interface resource is currently unavailable. Recovery may require a restart of the IS-IS process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_CKTNUM_ALLOC_FAIL Failed to allocate circuit ID to interface [chars]: all [dec] IDs already in use
Explanation IS-IS failed to allocate a circuit ID to the specified LAN interface.
Recommended Action Reduce the number of LAN interfaces over which IS-IS is running.
Error Message%ROUTING-ISIS-4-INTF_CLNS_CLIENT_INIT Failed to initialize CLNS interface registry: [chars]
Explanation IS-IS failed to initialize its interface registration process with CLNS. It requires a restart of process for recovery.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_CLNS_LPTS_UPDATE Failed to [chars] LPTS entry for interface [chars]: [chars]
Explanation IS-IS failed to create or remove LPTS entry on the specified interface. It may require a restart of process for recovery.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_CLNS_MAC_ADDR_NOTIFY Failed to notify CLNS of a MAC address change on interface [chars]: [chars]
Explanation IS-IS failed to notify the CLNS protocol stack of MAC address changes to the specified interface. It requires a restart of process for recovery.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_CONFIG_ERROR Interface [chars] is already configured
Explanation This is a duplicate configuration received for the same interface. Most likely the previous cleanup (commit replace) or removal of ISIS config was not successful (CSCsy26037/CSCsv89872). ISIS may be in unstable state.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-4-INTF_FIND_FAIL Failed to lookup Interface Handle for interface [chars]: [hex] '[chars]'
Explanation An unexpected error occurred looking up an interface handle from an interface name. This may be due to a low memory condition but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-INTF_FWS_INIT Error during initialization of forward-referenced interface store: [chars]
Explanation IS-IS failed to initialize its storage for forward-referenced interfaces. This is may be due to lack of resources or an internal error (the error message will indicate which). It requires a restart of the process for recovery.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-INTF_IM_REG_FAIL Error registering for [chars] [chars] changes on interface [chars]: [hex], '[chars]'
Explanation IS-IS failed to register for notification of the specified changes on the specified interface and protocol. This may be an internal programming error, but is most likely to be a resource starvation problem.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider disabling and reenabling the interface within IS-IS configuration, or restarting the IS-IS process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_INACTIVE_AF Unexpected [chars] [chars] notification on [chars]
Explanation The specified event was unexpected because the address family is not active on that interface. The operation of IS-IS is not affected by this message and it may safely be ignored. The message is due to an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_IP_ARM_BATCH_UPDATE_FAIL Error [chars] for [chars] address changes on interface [chars]: [hex], '[chars]'
Explanation IS-IS failed to register with IP-ARM for notification of the address changes on the specified interface and address family. This may be an internal communication error, but is most likely to be a resource starvation problem.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider disabling and reenabling the interface within IS-IS configuration, or restarting the IS-IS process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_LAS_FAIL Failed [chars] [chars] link local addresses on [chars]: [hex], '[chars]'
Explanation An unexpected error occurred while accessing the link-local address details for the specified interface. As a result IS-IS will not be able to use the specified address-family on the specified interface. This could be due to a low memory condition or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-4-INTF_MAC_SIZE_ERR Incorrect MAC address size for [chars] (returned: [dec], expected: [dec])
Explanation The MAC address size returned for the specified interface does not match the expected size (6 bytes). This can be caused by a faulty hardware.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MCAST_JOIN_FAIL Error joining [chars] multicast group on [chars]: [chars]
Explanation IS-IS was unable to join the specified multicast group on the specified interface.
Recommended Action Restart the affected interface and, if the problem recurs, the IS-IS process. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MCAST_SIZE_ERR The multicast address is too large for [chars] (supplied: [dec], maximum: [dec])
Explanation The multicast address requested for the specified interface is larger than the maximum permissible size. This requires restarting the IS-IS process.
Recommended Action Restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MTU_REDUCED IS-IS MTU value of [unsigned int] on [chars] adjusted to [unsigned int] to accommodate fabric MTU
Explanation The IS-IS MTU was adjusted to accommodate the fabric MTU of the system. This new MTU may be smaller than the actual MTU allowable by the physical interface.
Recommended Action Check any MTU configuration for the interface to ensure that this is not a configuration error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_MTU_TOO_SMALL CLNS MTU value of [unsigned int] on [chars] is too small. Minimum acceptable value is [unsigned int]
Explanation The MTU for CLNS on the specified interface is too small to allow IS-IS to send packets over that interface. This may be due to a configuration error or an internal error.
Recommended Action Check any MTU configuration for the interface to ensure that this is not a configuration error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_NAME_FAIL Failed to lookup an interface name from its handle ([hex]): [hex], '[chars]'
Explanation An unexpected error occurred looking up an interface's name from it's handle. The error code should provide an indication of what the problem is. The most likely explanation is that the interface with the specified handle no longer exists although the message may be caused by low memory conditions or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-INTF_NSF_MEDIA_MISMATCH Media class mismatch between checkpoint table ([chars]) and reality ([chars]) on interface [chars]
Explanation IS-IS has detected a mismatch between the media class (i.e. Point to Point vs. LAN) of an interface as determined by IS-IS's checkpoint state and IM. As a result the interface will not participate in the NSF restart. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_PROTECT_INFRA_UPDATE Protect infra [chars] failed for interface [chars]: [hex], '[chars]'
Explanation IS-IS failed to register or unregister with protect infrastructure for high priority link-down notifications on the specified interface. IS-IS will still react to regular link-down events.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INTF_STORE_FAIL Error [chars] [chars] [chars] internal [chars] store: [hex], [chars]
Explanation IS-IS was unable to perform the specified operation on the specified interface. This is most likely to be a resource starvation problem, but may be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-4-INTF_UNKNOWN_MEDIA Unknown or unsupported interface media type ([chars]) on [chars]
Explanation This interface media is not supported by IS-IS. An IS-IS process restart is required for recovery.
Recommended Action Check the interface media name in the configuration and restart the IS-IS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-INVALID_LSP_LIFETIME L[unsigned int] LSP [chars] sn [hex] cs [hex] has invalid remaining life time [unsigned int], max allowed - [unsigned int]
Explanation IS-IS received invalid value for the remaining LSP life time using the timer library. IS-IS will handle this gracefully by limiting the value to maximum allowed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-IP_ARM_ADDR_INFO_FAIL Failed to [chars] for [chars] address information: [hex], '[chars]'
Explanation IS-IS has encountered an error while manipulating a set of interface IP addresses. This may be a resource starvation problem or an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-ITEMSIZE add_item_entry called with size [dec]: errant entry was not added to the LSP
Explanation add_item_entry called with size SIZE. An internal error occurred while this system was trying to construct its LSPs. The errant entry was not added to the LSP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-KEY_DEACTIVATE_FAIL Failure to deactivate Key Chain [chars]: '[chars]''
Explanation A call to the Key Chain library failed. This may indicate an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-LINK_TO_SELF Level [unsigned int] LSP [chars] contains a link advertisement to itself ([chars] MT ID). This link will be ignored in subsequent route calculations.
Explanation The specified LSP contains a link advertisement to itself and this link has been ignored. There is no possible impact to routing as the link would not be used by other routers in their calculations. This message is however indicative of a problem in the router which issued the LSP as it should not have advertised such a link.
Recommended Action Identify the source of the offending packet and correct it.
Error Message%ROUTING-ISIS-4-LSPCKSUM Bad L[dec] LSP [chars] checksum [hex] received on [chars], length [dec], should be [hex], bad count [dec]
Explanation Bad L-# LSP LSP-ID checksum ACTUAL-CKSUM received on INTERFACE-NAME, length PDU-LENGTH should be EXPECTED-CKSUM, bad count CKSUM-ERROR-COUNT. This system received a level L-# LSP with a wrong checksum. If the IS-IS configuration option 'isis-ignore-cksum-errors' is set, the packet has been ignored. Otherwise it has been handled according to the specification.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-4-LSPFULL L[unsigned int] LSP filled to capacity, dropping routes
Explanation L-LEVEL LSP filled to capacity and is dropping routes. This system cannot originate any more routes or adjacencies because it cannot build any more LSP fragments in which to advertise them.
Recommended Action This is usually caused by a misconfiguration, such as redistributing a large number of routes into IS-IS. Reduce the number of routes being redistributed into IS-IS to correct the problem.
Error Message%ROUTING-ISIS-4-LSPTOOBIG L[dec] LSP [chars] size [dec] bigger than interface [chars] MTU [dec], LSP dropped
Explanation L-LEVEL LSP LSP-ID size LSP-LENGTH is bigger than interface INTERFACE-NAME MTU INTERFACE-MTR. LSP dropped. This system was unable to flood an LSP out INTERFACE-NAME because the interface MTU was too small. The LSP has not been transmitted on the interface.
Recommended Action Configure the routing area and the interfaces with a consistent MTU.
Error Message%ROUTING-ISIS-4-MARTIAN Level [unsigned int] LSP [chars] contains an [chars] prefix advertisement to the invalid prefix [chars]. This prefix will be ignored in subsequent route calculations.
Explanation The specified LSP contains a prefix advertisement to an invalid martian prefix and the prefix has been ignored. As the prefix is invalid there should be no impact to routing as no traffic should be destined to the prefix. This message is however indicative of a problem in the router which issued the LSP as it should not have advertised such a prefix.
Recommended Action Identify the source of the offending packet and correct it.
Error Message%ROUTING-ISIS-4-MAX_REDIST_PREFIXES Topology [chars] level [unsigned int] is [chars]exceeding the maximum number of redistributed prefixes
Explanation This configuration is redistributing more than the allowable number of prefixes into an IS-IS topology. IS-IS will not advertise some of these routes. This is to prevent inadvertent redistribution of the Internet via IS-IS.
Recommended Action Consider reconfiguring route redistribution into the IS-IS process. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-MEM_ALLOC_FAIL Failed to allocate [unsigned int] bytes for '[chars]'
Explanation The process failed to allocate memory for the specified resource. This could be because the IS-IS topology is too large for the memory installed in the router.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-MGD_TIMER_FAIL Error [chars] the [chars] [chars] timer: [chars]
Explanation IS-IS encountered an unexpected error using the Managed Timer library. This is most likely to be due to a low memory condition but may also be an internal programming error. The error message should provide more information about the cause.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-4-NSF_CHKPT_ACCESS_FAIL Failed to [chars] checkpoint record(s) [chars] [chars] table: [hex], '[chars]'
Explanation An unexpected error occurred while IS-IS was accessing entries in the specified checkpoint table. If this error occurs during an NSF Cisco restart then that NSF restart may be aborted in favour of a traditional restart. If this error occurs during normal operation then the relevant checkpoint table may not be correct, and a subsequent NSF restart may not succeed. If however the error does not recur then the checkpoint tables should synchronize. The error may be caused by a low memory condition or through programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-NSF_CHKPT_INIT NSF checkpoint init failure, [hex], '[chars]'
Explanation The IS-IS process failed to initialize the checkpoint service for the specified error reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-NSF_CHKPT_TABLE_FAIL Failed to [chars] [chars] checkpoint table: [hex], '[chars]'
Explanation An unexpected error occurred while IS-IS was accessing the specified checkpoint table. If this error occurs during an NSF Cisco restart then that NSF restart may be aborted in favour of a traditional restart. If this error occurs during normal operation then the relevant checkpoint table may not be correct, and a subsequent NSF restart may not succeed. The error may be caused by a low memory condition or through programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-NSF_CREATE_FAIL Failed to create L[unsigned int] NSF adjacency to [chars] ([chars]) ([chars])
Explanation An error occurred when creating an NSF adjacency.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-NSF_TE_TUNNEL_RESTORE_FAIL Failed to restore L[unsigned int] TE tunnel ([hex]) to [chars] ([chars]) ([hex], [chars])
Explanation An unexpected error occurred while recreating TE tunnel from the checkpointed information. NSF may abort.
Recommended Action Restart the ISIS process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-OSI_SOKT_FAIL Socket operation '[chars]' failed: [chars]
Explanation Failure to perform a socket operation occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-P2P_CONFIG_MISMATCH L[unsigned int] [chars] configuration on P2P interface [chars] will not be used
Explanation Any level specific configuration on a P2P interface is ignored. The configuration may be accepted but not used if the interface type is unknown or changed later to point-to-point.
Recommended Action Configure the same parameter without using any level extension.
Error Message%ROUTING-ISIS-4-REDIST_FAIL Error [chars] for redistribution of routes from [chars] [chars] into IS-IS
Explanation The RIB returned an unexpected error when IS-IS attempted to (de)register for the redistribution of routes in the specified topology and owned by the specified protocol. If this is a registration error then routes from the specified protocol may not be advertised in IS-IS's system LSPs. If this is a deregistration error then IS-IS may receive unnecessary redistribution updates from the RIB but the system LSPs will be correctly generated. The problem may be caused by a low memory condition but is most likely to be an internal programming error.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Consider restarting the IS-IS and/or the RIB processes.
Error Message%ROUTING-ISIS-4-RSI_C_REGISTRATION_FAIL Attempt to register for a VRF failed: [chars] ([hex])
Explanation IS-IS failed to register for notification of changes to a VRF.
Recommended Action This failure may be due to lack of resources. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-4-SAMESYSID_DIFFHOST Received self originated LSP with system ID [chars], on interface [chars], differs in hostname; Local hostname [chars], Received hostname [chars]. Please check if this host was connected inadvertently to the network or if the local hostname has been changed.
Explanation An LSP is received with a System ID same as the local System ID but with a different hostname. This could be happen in the following cases:
1.
2.
Recommended Action If case 1, check the configuration of other routers in the area for duplicate system IDs. If case 2, ignore the message.
Error Message%ROUTING-ISIS-4-SEQNUM_WRAP Sequence number wrapped in LSP [chars].
Explanation An LSP originated by this system has had its sequence number wrap around to 0. The IS-IS specification states that this system should shutdown for 20 minutes waiting for the LSP to age out before resuming routing.
Recommended Action This condition can only occur if a network has been operational for several years, or if a network has been misconfigured for a long time. Disable the IS-IS routing process for max-lsp-lifetime and then restart it to clear the problem. Alternative approaches include changing the SYSTEM-ID or, if this occurred with a pseudo-node LSP, lowering the priority of the interface.
Error Message%ROUTING-ISIS-4-SETSOCKOPT_FAIL Error setting the value of the '[chars]' IS-IS network socket option to '[chars]' (length [unsigned int]): [chars]
Explanation IS-IS encountered an error while configuring the socket it uses for network I/O. As a result the socket is unusable and IS-IS cannot perform I/O. IS-IS will attempt to recover by closing the current socket and schedule an attempt to reconnect.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Consider restarting the IS-IS process.
Error Message%ROUTING-ISIS-4-SHOW_NOMEM Internal memory allocation failure, display incomplete
Explanation The requested display output may be incomplete due to an internal memory allocation problem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-SHUTDOWN Process is shutting down ([chars]): [chars]
Explanation IS-IS has encountered a problem which means that is no longer able to continue and so it is shutting down. The message includes a brief description of the problem but will also have been preceded by another message providing a more detailed description of the problem. There are several types of reason why IS-IS may have to shutdown which include a fatal error during process initialization, a fatal problem with a critical service during normal operation, and a roll-over of one of the local system's LSP's sequence numbers. The message also describes whether or not IS-IS has automatically been restarted.
Recommended Action Follow the instructions associated with the preceding message. If an automatic restart has been scheduled, then IS-IS may recover automatically. If a manual restart is required, then 'process start isis' is required to recover.
Error Message%ROUTING-ISIS-4-SNPTOOBIG L[dec] SNP size [dec] too big for interface [chars] MTU [dec], trimmed to interface MTU
Explanation L-LEVEL SNP size SNP-LENGTH is bigger than interface INTERFACE-NAME MTU INTERFACE-MTR, trimmed to interface MTU. This system was unable to flood an SNP out INTERFACE-NAME because the LSP MTU setting is too big for the interface MTU. The SNP packet size was trimmed to fit the interface MTU.
Recommended Action Configure the LSP MTU to a size that will fit within the interface MTU.
Error Message%ROUTING-ISIS-4-THREAD_SPURIOUS_PULSE Received a spurious pulse in thread [chars] (pulse value: [hex])
Explanation IS-IS received a spurious (unexpected) pulse value and will ignore it.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-4-TIMESTAMP_FAIL Error recording a timestamp ([dec])
Explanation An unexpected error occurred while recording a timestamp. This implies an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-UNKNOWN_ADDRESS_FAMILY Unknown address family [unsigned int]
Explanation IS-IS has encountered an unrecognized address family ID. This is an internal programming error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-4-WD_METRIC_NOT_CONF In the topology [chars] [chars] has a wide metric of [unsigned int] but level L[unsigned int] is configured to generate narrow metrics. Maximum narrow value [unsigned int] is used instead
Explanation The specified interface and topology has been configured with a metric value that requires metric-style wide to be configured for the relevant level.
Recommended Action Configure metric-style wide for the topology and area.
Error Message%ROUTING-ISIS-4-ZERO_COST_LINK Level [unsigned int] LSP [chars] contains an invalid link advertisement to [chars] ([chars] MT ID) with a metric of 0. This link will be ignored in subsequent route calculations.
Explanation The specified LSP contains a link advertisement with an invalid metric of 0. Zero cost links have the potential to break the SPF algorithm and are not permitted by the IS-IS specification (ISO 10589 version 2) and so the IOS-XR router will ignore the link in any subsequent route calculations. As a result traffic which should be routed via the affected routers may be dropped or enter a routing loop.
Recommended Action Identify the source of the offending packet and correct it.
Error Message%ROUTING-ISIS-4-ZEROHOLDTIME IIH zero holdtime from [chars]
Explanation IS-IS has received an IIH containing a zero holdtime from a neighbor with which no adjacency currently exists. The IIH has been discarded. The message indicates the interface and, in the case of a LAN interface, the SNPA from which the IIH was received.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-5-ADJCHANGE Adjacency to [chars] ([chars]) ([chars]) [chars], [chars]
Explanation Adjacency to SYSTEM-ID (INTERFACE-NAME) Up|Down, REASON. The adjacency to the system with SYSTEM-ID has gone up or down due to REASON.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-5-AUTH_COMPUTE_FAILED Key Chain digest computation for [chars] failed due to [chars]
Explanation The process encountered an error when computing the authentication digest. This may be due to misconfiguration on the local or remote system. It is possible that no currently valid keys are available.
Recommended Action Check the password and authentication configurations on the local system.
Error Message%ROUTING-ISIS-5-AUTH_FAILURE_DROP Dropped [chars] from [chars] due to [chars]
Explanation The process encountered an error when authenticating an incoming PDU and dropped the PDU. This may be due to misconfiguration on the local or remote system.
Recommended Action Check the password configuration on the local and remote systems.
Error Message%ROUTING-ISIS-5-AUTH_VERIFY_FAILED Key Chain digest verification for incoming [chars] failed due to [chars]
Explanation The process encountered an error when verifying the authentication digest. This may be due to misconfiguration on the local or remote system. It is possible that no currently valid keys are available or the remote system is using an invalid authentication key.
Recommended Action Check the password and authentication configurations on the local system.
Error Message%ROUTING-ISIS-6-ADJNSF [chars] L[unsigned int]: Neighbor [chars] [chars]
Explanation The adjacency on the INTERFACE-NAME and LEVEL with the system SYSTEM-ID STARTED responding or STOPPED responding during the NSF-restart of the SYSTEM-ID.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-6-ATOMIC_RING_FULL [chars] queue is full.
Explanation The atomic ring for the indicated queue is full.
Recommended Action If the situation persists, investigate whether there is resource starvation occurring.
Error Message%ROUTING-ISIS-6-DBG_UNKNOWN_TRACEPOINT_NAME Unknown debug filter tracepoint name [chars]
Explanation An unknown tracepoint name requested for a debug filter.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-6-ERR_DUPID Duplicate System ID [chars] already used by [chars] detected in IIH received on [chars]
Explanation IS-IS has received an IIH from a router claiming to have the same System ID as either the local system or another station on a LAN interface. The message indicates the interface and, in the case of a LAN interface, the SNPA from which the IIH was received. It also indicates whether you use this system ID, or the SNPA of the other station using the system ID.
Recommended Action Duplicate system IDs are usually the result of misconfiguration or a bridging loop in the network. Configure each router with a unique system ID, and ensure that there are no bridging loops in the network.
Error Message%ROUTING-ISIS-6-EVENT_CONN_DESTROY_FAIL Error destroying '[chars]' connection: [chars]
Explanation During process termination IS-IS failed to destroy a connection to a service provided by another process. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-6-EVENT_ERR Event handler error [dec]
Explanation Event handler error ERRNO. This system encountered an error ERRNO trying to get an event from the event handler.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-6-EVQ_DESTROY_FAIL Failed to destroy the [chars] event queue [hex]: [hex], '[chars]'
Explanation An unexpected error occurred while destroying an event queue. This is an internal programming error, but will not affect protocol operation as it occurred while IS-IS was destroying resources which are no longer required.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-6-FAIL_ADJADD Failed to create adjacency for [chars] ([chars]): [chars]
Explanation Failure to create adjacency to the displayed IS via the displayed interface for the reason specified.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-6-IIH_IF_ADDRESS IIH received from [chars] contains [chars] [chars] interface address: [chars]
Explanation IS-IS received an IIH from the specified source containing an invalid and potentially unusable interface address for the specified address family. The message contains details of why the interface address is invalid. The message implies that the router sending the bad IIH is either misconfigured or is not conforming to the IS-IS specification. If the message describes the address as unusable, then IS-IS is not able to use the adjacency as a next hop for the specified address family. Otherwise IS-IS will still attempt to use the adjacency as a next hop.
Recommended Action Using the contents of the error message as a guide, check the configuration of the router sourcing the IIH or contact the router's vendor.
Error Message%ROUTING-ISIS-6-INFO_STARTUP_ABORTED [chars] controlled start aborted. Reason: [chars]
Explanation Startup state-machine controlled startup aborted for the specified reason. Some of the reasons indicate an internal software error, or the failure of anther software service. Other reasons are due to configuration or other operational problems. Finally NSF restart may abort due to no adjacencies being restored, if there were in fact no adjacencies present prior to restart/switchover then this is expected behavior.
Recommended Action If the indicated reason can be corrected with configuration changes, then do so; otherwise, Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-6-INFO_STARTUP_FINISH [chars] controlled start completed
Explanation Startup state-machine controlled startup process ends here.
Recommended Action None.
Error Message%ROUTING-ISIS-6-INFO_STARTUP_FORCED_COLD Resorting to cold start: [chars].
Explanation The startup state-machine has determined that a cold (re)start must be performed regardless of current NSF configuration for the reason specified.
Recommended Action None.
Error Message%ROUTING-ISIS-6-INFO_STARTUP_START [chars] controlled start beginning
Explanation Startup state-machine controlled startup process begins here.
Recommended Action None.
Error Message%ROUTING-ISIS-6-INTF_MAC_ADDR_CHG_INVALID MAC address change notification received for P2P interface: [chars]
Explanation IS-IS received MAC address change notification for non LAN interface. ISIS ignores the notification. The message is only informational.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-6-NO_INPUTBUF Unable to allocate input buffer
Explanation This system failed to allocate an input buffer because there was insufficient memory to do so.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ISIS-7-ERR_CREATEMQ Error in creating message queue to MPLS
Explanation The process failed to create a message queue to communicate with MPLS.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-7-ERR_MSG Error in reading message: [chars]
Explanation The process failed to read the message.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-7-ERR_MSGLEN Error in reading message length: [chars]
Explanation The process failed to read the message length.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-7-ERR_RCV_PAKTYPE Invalid IS-IS packet type [unsigned int] received on [chars] ([chars] code)
Explanation An invalid packet was received on the specified interface (and, in the case of a LAN interface, SNPA). The packet is invalid because its type code is either unrecognized or inappropriate (e.g. a point to point IIH on a LAN interface). The packet has been ignored.
Recommended Action No action is required.
Error Message%ROUTING-ISIS-7-ERR_RECV_TE_MSG Received an invalid length TE message for [chars]: expected ([unsigned int]), received ([unsigned int])
Explanation The process has received an invalid length TE message. As a result, the TE message is ignored and TE tunnel may not come up.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-7-ERR_RECV_TE_MSG_VERSION Received an invalid version of TE message for [chars]: ([unsigned int])
Explanation The process has received a TE message with an incompatible version. As a result, the TE message is ignored and TE tunnel may not come up.
Recommended Action Collect output from 'show tech-support mpls traffic-eng'. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-7-ERR_SEND_TE_MSG Failed to send a [chars] message to TE
Explanation The process encountered an error while sending message to TE.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ISIS-7-STALE_PNODE_PURGE Skipping stale purge event for L[dec] LSP [chars] pseudo-node
Explanation The router has re-elected itself DIS after initiating a purge of its L-LEVEL LSP LSP-ID due to a previous resignation.
Recommended Action No action is required.
LDP Messages
Error Message%ROUTING-LDP-3-ERR_BACKEND Backend scan failed for '[chars]': [chars]
Explanation LDP failed backend scan for some tuple path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-ERR_GENERAL [chars]
Explanation A general error occurred within LDP. The details appear in the output.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-ERR_INIT_SYNC_MISSING_SOCK Init Sync Done: Missing Pending Socket([chars])
Explanation Received Init Sync Done notification but socket was not in pending database.
Recommended Action No action is required.
Error Message%ROUTING-LDP-3-ERR_LPTS_FILT Failed to [chars] LPTS filter for local [chars] remote equals [chars]: [chars]
Explanation Installation of LPTS filters for targeted LDP neighbors failed. This failure can prevent sessions to LDP targeted neighbors from being established.
Recommended Action Verify the number of targeted neighbors, either configured or L2VPN. Check 'show lpts pifib..' for statistics and limits.
Error Message%ROUTING-LDP-3-ERR_LSD_INTF LSD Intf-[chars] failed for [chars] (ifh [hex]): [chars]
Explanation LDP encountered some problem while trying to enable/disable MPLS on an interface via LSD server.
Recommended Action Make sure that LSD is running and LDP is connected/registered with it.
Error Message%ROUTING-LDP-3-ERR_LSD_REG LSD application registration failed: [chars]
Explanation LDP encountered a problem while trying to register with LSD server.
Recommended Action Make sure that LSD is running and LDP is connected to it.
Error Message%ROUTING-LDP-3-ERR_TCP_ENQUEUE_MSG_INVALID_TX_CTX TCP: Msg Enqueue Failed: Invalid Tx Ctx.
Explanation This error indicates an invalid transmit.
Recommended Action Remove source of transmit.
Error Message%ROUTING-LDP-3-ERR_TCP_ENQUEUE_MSG_NOT_ACTIVE TCP: Msg Enqueue Failed: Node isn't active.
Explanation Standby Node tried to transmit LDP message.
Recommended Action Remove source of transmit.
Error Message%ROUTING-LDP-3-INCONSISTENCY An internal inconsistency was detected:[chars]
Explanation LDP has detected an internal inconsistency. Please capture a core file for analysis.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-NSR_ACK_CHK_FAILED NSR ACK CHK failed: [chars]; count [dec]
Explanation NSR ACK CHK failed. Please perform show mem heap for analysis.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-NSR_IPC_TRANSPORT_FAILURE Repeated internode transport failures, re-initiating NSR sync
Explanation LDP encountered too many consecutive transport errors while trying to send NSR messages which triggers NSR sync again.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-3-NSR_PEER_SYNC_RX_ERR Peer [chars]; op equals '[chars]'; [chars]
Explanation Standby LDP instance encountered an error during processing of NSR synchronization data sent by Active LDP instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-4-BAD_PDU_LENGTH A message with botched PDU length is received from peer [chars]
Explanation A message with botched PDU length is received from the network.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-4-BAD_TLV TLV Check failed for a message (type [hex]) received from peer [chars]
Explanation A message with a bad TLV is received from the network.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-4-CAP_CHANGE LDP session(s) reset required to propagate LDP capability changes
Explanation A capability was installed/updated/uninstalled by an LDP client. LDP peers will not learn of the change until the LDP session has been reset.
Recommended Action Reset LDP neighbor using the 'clear mpls ldp neighbor ...' command.
Error Message%ROUTING-LDP-4-CAP_CHANGE_DYNAMIC LDP session(s) reset required to propagate capability change of '[hex] ([chars])' to peers that do not support Dynamic Announcement capability
Explanation A capability was installed/updated/uninstalled by an LDP client. LDP peers that don't support Dynamic Announcement will not learn of the change until the LDP session has been reset.
Recommended Action Use the 'show mpls ldp neighbor capability' command to determine which neighbors need to be reset. Reset LDP neighbor using the 'clear mpls ldp neighbor ...' command.
Error Message%ROUTING-LDP-4-DEPRECATED_RTRID 'router-id interface command is deprecated. Delete 'router-id [chars]' and reconfigure 'router-id ip_addr'.
Explanation MPLS LDP 'router-id interface' command is deprecated.
Recommended Action Use 'router-id ip_addr'.
Error Message%ROUTING-LDP-4-DISCOVERY_SLIP CPU load or blockage caused latent tx of UDP discovery to [chars]: interval equals [dec] sec, expected equals [dec] sec. Hold equals [dec] sec
Explanation Heavy CPU load or process blockage resulted in slip of discovery transmission. Possibly resulting in session/adjacency flap.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-4-DUP_ADDR_RCVD Duplicate Address [chars] advertised by peer [chars] is already bound to peer [chars]
Explanation LDP received an address advertisement for an address from a peer, but the address is already bound to a different peer.
Recommended Action Fix the misconfiguration in the network.
Error Message%ROUTING-LDP-4-DUP_ADDRS [dec] Duplicate address(es) advertised by more than one peer
Explanation LDP peer address database has some duplicate addresses which are received from (and hence bound to) more than one peer. The presence of one or more duplicate address confuses LDP control plane and may lead to potential traffic blackholing due to unlabeled forwarding path setup for paths using this address as the nexthop IP address.
Recommended Action Find all peers duplicate addresses present in the network by running 'show mpls ldp neighbor detail' command, and then fix the misconfiguration in the network.
Error Message%ROUTING-LDP-4-MAX_NEIGHBORS Rejecting LDP neighbor ([chars]): Reached maximum ([dec]) number of neighbors supported.
Explanation Reached maximum number of neighbors supported.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-4-TX_KEEPALIVE_SLIP CPU load or blockage caused latent tx of LDP keepalive to [chars]: interval equals [dec] sec, expected equals [dec] sec. Hold equals [dec] sec
Explanation Heavy CPU load or process blockage resulted in slip of discovery transmission. Possibly resulting in session.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-5-ADJ_CHANGE Adjacency ([chars]) [chars] with Nbr [chars] [chars] [chars]
Explanation A LDP adjacency has changed state (up/down). If adjacency has went down, then a reason for adjacency going down is also displayed. This message appears only if the log adjacency command is configured for the LDP process.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-GR GR session [chars] (instance [dec]) [chars]
Explanation An LDP GR session state change has occurred, such as disconnected, reconnected, timed out, forced abort, and cleaned up. This message appears only if the log graceful-restart command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-GR_ID_CHANGE GR session [chars] identifier changed to [chars]
Explanation A previously known GR peer has reconnected with a new ldp-id.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-GR_RESTART_COMPLETE GR forwarding state hold timer has expired
Explanation After LDP local restart, LDP GR forwarding state hold timer has expired, and MPLS forwarding is now being updated and reinstated by LDP application. This message appears only if the log graceful-restart command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-NBR_CHANGE Neighbor [chars], [chars] [chars]
Explanation A LDP neighbor has changed state (up/down). If neighbor has went down, then a reason for session going down is also displayed. This message appears only if the log neighbor command is configured for the LDP process.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-NSR_SYNC_DONE Initial synchronization successfully done for [dec] peers
Explanation LDP Non-stop routing initial-sync event has completed successfully for some or all peers. This message appears only if the mpls ldp log nsr command is configured.
Recommended Action If number of peers do not match the number of peer for SYNC_START, then Check LDP logs and traces to see why not all attempted peers were successfully synced.
Error Message%ROUTING-LDP-5-NSR_SYNC_LOST Global synchronization lost
Explanation LDP Non-stop routing synchronization lost with the standby node. This message appears only if the mpls ldp log nsr command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-NSR_SYNC_PEER_DONE Peer [chars] initial synchronization done
Explanation LDP Non-stop routing peer initial-sync event has completed successfully. This message appears only if the mpls ldp log nsr command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-NSR_SYNC_PEER_LOST Peer [chars] synchronization lost
Explanation LDP Non-stop routing synchronization lost for the peer. This message appears only if the mpls ldp log nsr command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-NSR_SYNC_START Initial synchronization started for [dec] peers
Explanation LDP Non-stop routing initial-sync event has been started for all eligible peers. This message appears only if the mpls ldp log nsr command is configured.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-SESSION_PROTECTION [chars] for peer [chars]
Explanation An informational LDP notice was generated for a Session Protection event.
Recommended Action No action is required.
Error Message%ROUTING-LDP-5-SHUTDOWN LDP process is shutting down due to '[chars]' memory state.
Explanation LDP process exiting due to unknown/critical node memory state.
Recommended Action Start 'mpls_ldp' process after memory state goes normal.
Error Message%ROUTING-LDP-6-ISYNC_CHKPT_LIMIT Limit reached for maximum ([dec]) number of neighbors per interface
Explanation LDP checkpointing has limit for maximum number of neighbors per interface due to LDP IGP Sync feature requirements. It is not recommended to cross the limit provided by Engineering. If crossed, undesired affects can be seen and LDP IGP Sync feature may not work.
Recommended Action Limit number of neighbors to the value as provided in Engineering guidelines
Error Message%ROUTING-LDP-7-ERR_INIT '[chars]' ([chars])
Explanation An internal system error occurred during initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LDP-7-ERR_INIT_FATAL Failed to initialize '[chars]': [chars]: Process now terminating
Explanation A fatal error occurred during initialization of an LDP subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
LMRIB_API Messages
Error Message%ROUTING-LMRIB_API-3-ASYNC_ERR Asynchronous error: [chars]
Explanation An unhandled asynchronous error occurred in the LMRIB API.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LMRIB_API-3-CORRPT Corrupted update: [chars]. (expected [dec] bytes, got [dec] bytes)
Explanation A corrupted update was received from the LMRIB by the LMRIB API.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LMRIB_API-3-GEN_ERR [chars]
Explanation Error occurred in lmrib client lib.
Recommended Action No action is required.
Error Message%ROUTING-LMRIB_API-3-GENINITFAIL Initialization failed: [chars] [chars]
Explanation Error occurred at client initialization.
Recommended Action No action is required.
Error Message%ROUTING-LMRIB_API-3-RPC_FAIL RPC failure: [chars]
Explanation An RPC-related error occurred in an RPC call from the LMRIB API.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LMRIB_API-7-ASYNC_WAR Warning: [chars]
Explanation A recoverable error condition occurred in the LMRIB API.
Recommended Action No action is required.
LSPV Messages
Error Message%ROUTING-LSPV-3-BAG_REG_ERR bag(s) registration failed: [chars]
Explanation Some error occurred while trying to register edm bags. The text of the message displays the failed operation with error code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-3-SYSDB_BIND_ERR sysdb_bind failed for '[chars]': [chars]
Explanation Some error occurred in sysdb bind operation bind. The text of the message displays the failed operation for the bindpoint with error code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-3-SYSDB_ERR [chars] failed: [chars]
Explanation Some error occurred in sysdb operation. The text of the message displays the failed operation with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-4-show_timeout [chars]
Explanation It was not possible to obtain the lock required to access the databases. This may be due to the main thread being very busy processing events.
Recommended Action Wait a few minutes, and re-attempt to issue the show command.
Error Message%ROUTING-LSPV-7-ERR_EVENT [chars] failed: error equals [hex] ([chars])
Explanation Some error occurred in event/event manager/event connection operations. The text of the message displays the failed operation with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-7-ERR_GENERAL [chars] failed: error equals [hex] ([chars])
Explanation Some requested operation failed. The text of the message displays the failed operation with error code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-7-ERR_INIT Failed to init '[chars]'. Process now terminating
Explanation Initialization of some subsystem failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-7-ERR_INIT_RC Failed to init '[chars]': error equals [hex] ([chars]). Process now terminating
Explanation Initialization of some subsystem failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-LSPV-7-ERR_TIMER [chars] failed: error equals [hex] ([chars])
Explanation Some error occurred in operations with mdg timers. The text of the message displays the failed operation with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MFWD_MA Messages
Error Message%ROUTING-MFWD_MA-3-CFG_ERR [chars] cfg counter already 0. Can't decrement : Item is [chars].
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_DEBUG_INIT_EVENT Failed to initialize and chain together the debug event descriptors : [chars]
Explanation An error related to the debugging subsystem occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_DEBUG_REG Sysdb registration for debug config failed : [chars]
Explanation An error related to the debugging subsystem occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_EVM_ASYNC_ATTACH [chars] : [chars]
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_EVM_CONN_CREATE Event connection create for [chars] failed : [chars].
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_EVM_CONN_NOTIFY Event connection notify for [chars] failed : [chars].
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_EVM_CONN_OPEN Event connection open for [chars] failed : [chars].
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_EVM_CREATE Cannot create event manager : [chars]
Explanation An unrecoverable error occurred at system initialization time.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_IMC_CONTROL_SERVER_BIND Error in imc control server bind : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_LTRACE_INIT [chars] : [chars]
Explanation An unrecoverable error occurred at system initialization time.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_MEM_ALLOC [chars]
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_MEM_FAIL [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_MEM_FAIL_1 [chars] : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_BAG_DECODE Error in bag decoding : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_BAG_FREE_INDIRECTIONS Error in bag free : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_BAG_REG Cannot register bags : [chars].
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_BIND Error in sysdb bind : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_DATALIST_FREE Error in datalist free : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_DATALIST_NEXT Error in datalist next : [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_EDM_FNS_INIT SysDB Oper - [chars] failed : [chars].
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_EDM_REG SysDB Oper - [chars] failed : [chars].
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_REG_VERIFY SysDB operation [chars] failed: [chars]
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-ERR_SYSDB_VRFN_FNS_INIT SysDB operation [chars] failed: [chars]
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-GEN_ERR [chars] failed : [chars].
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-GENINITFAIL Initialization failed: [chars] [chars]
Explanation An unrecoverable error occurred at system initialization time.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-IDB_ERR [chars] failed for [chars] [[hex]] : [chars]
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MFWD_MA-3-IM_UPDATE_IDB_HANDLE_MISMATCH idb [chars] has handle [[hex]], IM update has [[hex]]
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MOFRR_FLOW Messages
Error Message%ROUTING-MOFRR_FLOW-3-WD_OOR_GREEN Total number of MoFRR enabled multicast routes is no longer at maximum ([unsigned int]).
Explanation By removing the over-configured MoFRR routes, the total number of MoFRR enabled flows is being reduced. When the total number is first time reduced to exactly 75% of maximum supported (1024) MoFRR routes of current release, i.e., 768 routes, this message will be printed on the console and only once.
Recommended Action None.
Error Message%ROUTING-MOFRR_FLOW-3-WD_OOR_RED Total number of MoFRR routes has reached maximum ([unsigned int]). MoFRR will not be supported on new routes.
Explanation Currently ASR9K supports maximum 1024 flows which are guaranteed to have traffic switchover time within 50 ms. In addition, a line card encounters HW out-of-resource condition when the total number of MoFRR routes reaches 2048 MoFRR routes. Thus, any new configured 'MoFRR' beyond 1024 flows are not supported.
Recommended Action
1.
a.
b.
2.
a.
3.
a.
MPLS_ALM Messages
Error Message%ROUTING-MPLS_ALM-7-ERR_GENERAL [chars] : [chars]
Explanation An internal system error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_FWD Messages
Error Message%ROUTING-MPLS_FWD-2-NO_MEM No memory for '[chars]'
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_FWD-3-BAG_REG_ERR bag(s) registration failed: [chars]
Explanation Some error occurred while trying to register edm bags. The text of the message displays the failed operation with error code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_FWD-3-ERR_GENERAL [chars] failed: [chars]
Explanation Some requested operation failed. The text of the message displays the failed operation with error code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_FWD-3-EVENT_ERR [chars] failed: [chars]
Explanation Some error occurred in event/event manager/event connection operations. The text of the message displays the failed operation with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_FWD-3-SYSDB_BIND_ERR sysdb_bind failed for '[chars]': [chars]
Explanation Some error occurred in sysdb bind operation bind. The text of the message displays the failed operation for the bindpoint with error code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_FWD-3-SYSDB_ERR [chars] failed: [chars]
Explanation Some error occurred in sysdb operation. The text of the message displays the failed operation with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_HW Messages
Error Message%ROUTING-MPLS_HW-2-ERROR [chars]. Error equals [chars] (errno equals [dec]).
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_TLU_ALLOC [chars]. Error equals [chars] (errno equals [dec]).
Explanation Hardware memory allocation for table lookup unit (TLU) failed. This can be because the system has more forwarding entries than supported limits or there is a software defect.
Recommended Action Please collect output of show tlu server summary [egress/ingress] loc to see why the line card is running out of forwarding entries. Then try to reduce the entries if possible. Copy the error message and report to your technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_TLU_WRITE [chars]. Error equals [chars] (errno equals [dec]).
Explanation Hardware memory write for table lookup unit (TLU) failed. This can because 1) connection to mipc lost. 2) mipc/metro problem.
Recommended Action Please collect output of show pse ipc clinet-connection all loc and show asic-errors pse [0|1] all loc . Copy the error message and report to technical support representative.
Error Message%ROUTING-MPLS_HW-2-ERROR_WITH_LABEL [chars]. Error equals [chars] (errno equals [dec]). Out label equals [dec].
Explanation There was a critical system call failure resulting in a failure to provide some system service as indicated in the message text.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-6-INFO [chars]. Error equals [chars] (errno [dec]).
Explanation There was an internal failure that may impact non-essential system function.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-MPLS_HW-6-INFO_WITH_LABEL [chars]. Error equals [chars] (errno [dec]). Out label equals [dec].
Explanation There was an internal failure that may impact non-essential system function.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
MPLS_IMC_CLIENT Messages
Error Message%ROUTING-MPLS_IMC_CLIENT-3-ERR_IMC MPLS LIB IM client could not register for debugging ([chars])
Explanation MPLS LIB IM client library failed to register for debugging.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_IO Messages
Error Message%ROUTING-MPLS_IO-3-ERR_MEM_ALLOC [chars] failed :[chars]
Explanation Some error occurred in Alloc/Chunk related memory operations. The text of the message displays the failed operation and the related memory construct. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_IO-6-ERR_GENERAL [chars]: [chars]
Explanation This is some informational message with cerrno.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_IO-7-ERR_IM [chars] failed: [chars]
Explanation Some error occurred in operations with IM. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_IO-7-ERR_PAK [chars] failed: [chars]
Explanation Some error occurred in Packet (IP/MPLS/ICMP) related operations. The text of the message displays the failed operation and the related error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_IO-7-ERR_TIMER [chars] failed for '[chars]': [chars]
Explanation Some error occurred in Managed Timer related operations. The text of the message displays the failed operation and the related timer construct with error code. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_IO-7-ERR_WAVL [chars] failed (tree equals [chars]): [chars]
Explanation Some error occurred in WAVL operations The text of the message displays the failed operation and the related wavl tree. The traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_LCAC Messages
Error Message%ROUTING-MPLS_LCAC-4-SHOW_WARNING The show thread waited [unsigned int] seconds and could not acquire the mutex. Aborting show request. Please try again. If this problem persists, please contact your technical service representative.
Explanation The show thread could not acquire the mutex to service the show request. The main thread in te_control may be busy/blocked/hogging while holding That mutex.
Recommended Action Try to run the show command again. If the error reoccurs, then check the state of the te_control process (show process te_control). If thread number 1 is blocked for an extended period of time, contact your technical service representative.
Error Message%ROUTING-MPLS_LCAC-7-ERR_INTERNAL [chars]
Explanation An internal system error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
MPLS_LSD Messages
Error Message%ROUTING-MPLS_LSD-2-ERR_MEM_ALLOC Insufficient memory for '[chars]', [unsigned int] bytes, terminating
Explanation MPLS LSD terminated due to lack of memory for a critical operation.
Recommended Action The system is running under very low memory condition. Collect MPLS LSD traces and restart mpls_lsd process
Error Message%ROUTING-MPLS_LSD-3-ERR_INVALID_THREAD Callback from ENS on incorrect thread, actual/expected equals [dec]/[dec] (CSCsd51829)
Explanation Detected single-threaded mpls-lsd code running on an unknown thread. This concurrency can result in corruption.
Recommended Action Collect LSD traces.
Error Message%ROUTING-MPLS_LSD-3-MULTI_IP_FPI_RW [chars]
Explanation Rewrite creation or modification failed due to presence of multiple IP route elements.
Recommended Action Collect LSD traces.
Error Message%ROUTING-MPLS_LSD-7-ERR_CHKPT Invalid label provided by Checkpoint ([dec])
Explanation MPLS LSD on Standby failed to add invalid label provided by CHeckpoint.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LSD-7-ERR_CLIENT_FAULT [chars]
Explanation Client error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LSD-7-ERR_GENERAL [chars]
Explanation Miscellaneous MPLS LSD error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_LSD-7-ERR_INIT Initialization of MPLS LSD failed, op equals '[chars]' ([chars])
Explanation MPLS LSD failed to initialize for the reason displayed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_NETIO Messages
Error Message%ROUTING-MPLS_NETIO-5-CLEAR_MAPPING_FAILED control clear mapping for [chars] mpls proto [dec] failed [chars]
Explanation MPLS could not clear control mapping for underlying protocol.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-5-SET_MAPPING_FAILED control set mapping for [chars] to [hex]/[hex] mpls proto [dec] failed [chars]
Explanation MPLS could not set control mapping for underlying protocol.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-7-BAD_ARP_DROP Pkt([pointer]) with no nexthop in HSSD, output interface - CH[hex]. MPLS label stack:[chars]. IP info:[chars]. HSSD info:[chars].
Explanation MPLS slowpath got a packet for which ARP needs to be done, but, it doesn't have the nexthop needed. The packet is dropped.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_NETIO-7-ERR_GENERAL [chars] FAILED: [chars]
Explanation Some miscellaneous error occurred. The text of the message explains the err/warning and traceback can be used to get the function/line number of error generating code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_STATIC Messages
Error Message%ROUTING-MPLS_STATIC-4-ERR_MEM_ALLOC Memory allocation failed for [chars]
Explanation Allocation of memory failed.
Recommended Action Add more memory.
Error Message%ROUTING-MPLS_STATIC-6-ERR_CONN Connection to the [chars] failed ([chars])
Explanation MPLS static process could not connect with a manager.
Recommended Action No action is required.
Error Message%ROUTING-MPLS_STATIC-7-ERR_INIT Initialization of MPLS Static failed - [chars] ([chars])
Explanation Initialization of the MPLS Static process failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MPLS_TE Messages
Error Message%ROUTING-MPLS_TE-3-CALLBACK_WRONG_THREAD A callback ([chars]) has been received in the wrong thread ([unsigned int], should be in [unsigned int]). The callback has not been handled.
Explanation A callback from the IOX-XR infrastructure was not handled by the MPLS-TE process because it was received in the wrong thread. The TE process may now be in an inconsistent state with the rest of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. The te_control process may be restarted in order to recover from this situation.
Error Message%ROUTING-MPLS_TE-3-CHKPT_XFORM_INVALID_DIR TE checkpoint translation received an invalid translation direction: [unsigned int]
Explanation The TE checkpoint table translation library was invoked with an invalid translation direction.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_TE-3-CONSISTENCY_CHECK '[chars]' had a value of '[chars]', which did not match the expected value '[chars]'.
Explanation A software bug when an internal data consistency check failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_TE-3-ERR_AUTO_TUN_BKP_ID_LIMIT_EXCEEDED Auto-tunnel backup creation failed because ID pool limit of [dec] exhausted
Explanation The creation of the auto-tunnel backup aborted since all IDs in the auto-tunnel backup ID range have already been allocated.
Recommended Action Increase the auto-tunnel backup ID range or remove unused auto-tunnel configuration.
Error Message%ROUTING-MPLS_TE-3-ERR_AUTO_TUN_BKP_TUN_DEST_LIMIT_EXCEEDED Auto-backup tunnel [dec] creation failed because maximum tunnel destination limit [dec] exhausted
Explanation The creation of the auto-tunnel backup aborted since it would have exhausted the tunnel destination scale limit.
Recommended Action Reduce configured/auto tunnels to below the system scale limit.
Error Message%ROUTING-MPLS_TE-3-ERR_AUTO_TUN_BKP_TUN_LIMIT_EXCEEDED Auto-backup tunnel [dec] creation failed because maximum tunnel limit [dec] exhausted
Explanation The creation of the auto-tunnel backup aborted since it would have exhausted the tunnel scale limit.
Recommended Action Reduce configured/auto tunnels to below the system scale limit.
Error Message%ROUTING-MPLS_TE-3-ERR_IM MPLS TE encountered error [chars] while [chars] via the Interface Manager
Explanation Interface Manager returned an error during a tunnel interface operation. The system internal tunnel status might now be inconsistent which might prevent the tunnel from coming up or traffic flowing over this tunnel to be dropped.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information:
1.
2.
3.
Error Message%ROUTING-MPLS_TE-3-ERR_INTERNAL_CHECK [chars](): line [unsigned int]: [chars]
Explanation An inconsistency in internal state was detected.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-ERR_INTERNAL_CHECK_RC [chars](): line [unsigned int]: [chars]: error [chars] ([hex])
Explanation An inconsistency in internal state was detected.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-ERR_LMRIB_LABEL_RW [chars] failed for Tunnel [dec] (LSP ID: [dec], Source: [chars], PHOP: [chars], NHOP: [chars], Label: [unsigned int], Role: [chars]) [error: [dec], [chars]]
Explanation A LMRIB Label Rewrite related error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Collect: -show logging -show tech-support mpls traffic-eng -show lmrib client trace for further analysis of the issue.
Error Message%ROUTING-MPLS_TE-3-ERR_LMRIB_TUNNEL_RW [chars] failed for [chars] (LSP ID: [dec], Label: [unsigned int]) [error: [dec], [chars]]
Explanation A LMRIB Tunnel Rewrite related error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Collect: -show logging -show tech-support mpls traffic-eng -show lmrib client trace for further analysis of the issue.
Error Message%ROUTING-MPLS_TE-3-ERR_MEM_ALLOC Memory allocation failed for [chars]
Explanation Allocation of memory failed.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MPLS_TE-3-ERR_SYSDB_BAG_DECODE [chars]: [chars]: [chars]
Explanation A Bag related error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-ERR_SYSDB_DELETE [chars]: [chars]: [chars]
Explanation A SysDB free related error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-ERR_SYSDB_GET [chars]: [chars] failed for path [chars] : [chars]
Explanation A sysdb error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-3-ERR_TRACE_INIT Traffic-eng event tracing subsystem initialization failed
Explanation Traffic-eng could not initialize the tracing module.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_TE-3-NONRESPONSIVE_CLIENT Client '[chars]' has not processed an update [dec] seconds after being notified. Forcing reconnect. PID equals [dec],
Explanation TE server is forcing the specified client to reconnect, as the client has not processed a notification after a substantial timeout period.
Recommended Action Collect 'show processes pidin location loc-name' to find out the unresponsive client. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MPLS_TE-4-SHOW_WARNING The show thread waited [unsigned int] seconds and could not acquire the mutex. Aborting show request. Please try again. If this problem persists, please contact your technical service representative.
Explanation The show thread could not acquire the mutex to service the show request. The main thread in te_control may be busy/blocked/hogging while holding That mutex.
Recommended Action Try to run the show command again. If the error reoccurs, then check the state of the te_control process (show process te_control). If thread number 1 is blocked for an extended period of time, contact your technical service representative.
Error Message%ROUTING-MPLS_TE-4-SHUTDOWN Process is shutting down ([chars]): [chars]
Explanation TE process has encountered a problem which means it is no longer able to continue and is shutting down. The message includes a brief description of the problem. The message also describes whether or not TE process has automatically been restarted.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Follow the instructions associated with this message. If message states that an automatic restart has been scheduled, then TE process will recover automatically. If a manual restart is required, then 'process start te_control' is required to recover.
Error Message%ROUTING-MPLS_TE-4-WARN [chars]
Explanation An internal system warning occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-4-WARNING_FSM_EVENT_DROP Traffic-eng FSM dropped an event ([chars]) for S2L (tid [unsigned int], etid [chars], lspid [unsigned int], p2mpid [unsigned int], subgroupid [unsigned int])
Explanation Traffic-eng FSM dropped an event, because the S2L was created after the event was posted.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
Error Message%ROUTING-MPLS_TE-5-FRR Backup Tunnel ([chars], LSP Id: [unsigned int]) state changed to [chars].
Explanation The specified backup tunnel interface has changed its FRR status.
Recommended Action None. This is a solicited message (by 'logging events frr-protection' configuration) and is informative only.
Error Message%ROUTING-MPLS_TE-5-LSP_INSUFFICIENT_BW [chars] (LSP Id: [unsigned int]) failed to [chars] because of insufficient bandwidth.
Explanation The specified interface, with the specified LSP Id, cannot be setup or reoptimized because of insufficient bandwidth. The first %s refers to the tunnel name and the second %s. refers to either 'setup' or 'reoptimize'. LSP Id will be always 0 (zero), if failure happens during setup time.
Recommended Action None. This is a solicited message (by 'logging events lsp-status insufficient-bandwidth' interface configuration). User may verify reserved bandwidth on link as shown in the output of 'show mpls traffic-eng link-management bandwidth-allocation'.
Error Message%ROUTING-MPLS_TE-5-LSP_PREEMPT [chars] (LSP Id: [unsigned int]) has been preempted at [chars].
Explanation The specified interface, with specified LSP Id, has been preempted at specified IP Address or local node. The first %s refers to signalled tunnel name and the second %s refers to either the IP Address (of the remote node) or 'local node'.
Recommended Action None. This is a solicited message (by 'logging events preemption' configuration). User may verify reservable bandwidth on remote or local node as specified by the message.
Error Message%ROUTING-MPLS_TE-5-LSP_REOPT [chars] (old LSP Id: [unsigned int], new LSP Id: [unsigned int]) has been reoptimized; reason: [chars].
Explanation The specified interface, with the old LSP Id, has been reoptimized with the new LSP Id, because of the specified reason. The first %s refers to the tunnel name, and the second %s refers to the reason of reoptimization trigger. The trigger reasons are:
–
–
–
–
–
–
–
–
–
–
Recommended Action None. This is a solicited message (by 'logging event lsp-status reopt' interface configuration) and is informative only.
Error Message%ROUTING-MPLS_TE-5-LSP_REROUTE [chars] (LSP Id: [unsigned int]) has been fast-rerouted.
Explanation The specified interface has been rerouted.
Recommended Action None. This is a solicited message (by 'logging event lsp-status reroute' interface configuration) and is informative only.
Error Message%ROUTING-MPLS_TE-5-LSP_REROUTE_PENDING [chars] (LSP Id: [unsigned int]) is in re-route pending state.
Explanation The specified interface is fast-reroute enabled and in UP state; path verification failed but it did not take down the interface. Interface is now in re-route pending state and may stay in this state forever until the interface finds a valid path.
Recommended Action This is a solicited message (by 'logging event lsp-status reroute' interface configuration). User may verify interface configuration and network topology.
Error Message%ROUTING-MPLS_TE-5-LSP_REROUTE_PENDING_CLEAR [chars] (old LSP Id: [unsigned int], new LSP Id: [unsigned int]) has been [chars].
Explanation The specified interface is fast-reroute enabled and in UP state; earlier path verification failed but it did not take down the interface and got into reroute-pending state. Interface is now getting out of re-route pending state as a result of reoptimization or CLI changes.
Recommended Action None. This is a solicited message (by 'logging event lsp-status reroute' interface configuration).
Error Message%ROUTING-MPLS_TE-5-LSP_SWITCH [chars] (Standby LSP Id: [unsigned int]) [chars]
Explanation The specified interface has changed operational state.
Recommended Action None. This is a solicited message (by 'logging event lsp-status switch' interface configuration) and is informative only.
Error Message%ROUTING-MPLS_TE-5-LSP_UPDOWN [chars] (LSP Id: [unsigned int]) state changed to [chars]
Explanation The specified interface has changed operational state.
Recommended Action None. This is a solicited message (by 'logging event lsp-status state' interface configuration) and is informative only.
Error Message%ROUTING-MPLS_TE-5-S2L_INSUFFICIENT_BW [chars] (LSP Id: [unsigned int] Dest: [chars]) failed to [chars] because of insufficient bandwidth.
Explanation The specified P2MP Sub-LSP, with the specified LSP Id and destination, cannot be setup or reoptimized because of insufficient bandwidth. The first %s refers to the tunnel name, the second %s refers to Sub-LSP destination, and the second %s refers to either 'setup' or 'reoptimize'. LSP Id will be always 0 (zero), if failure happens during setup time.
Recommended Action None. This is a solicited message (by 'logging events sub-lsp insufficient-bandwidth' P2MP destination configuration). User may verify reserved bandwidth on link as shown in the output of 'show mpls traffic-eng link-management bandwidth-allocation'.
Error Message%ROUTING-MPLS_TE-5-S2L_PREEMPT [chars] (LSP Id: [unsigned int] Dest: [chars]) has been preempted at [chars].
Explanation The specified P2MP Sub-LSP, with specified LSP Id and destination, has been preempted at specified IP Address or local node. The first %s refers to signalled tunnel name. The second %s refers to Sub-LSP destination and the third %s refers to either the IP Address (of the remote node) or 'local node'.
Recommended Action None. This is a solicited message (by 'logging events sub-lsp preemption' P2MP destination configuration). User may verify reserved bandwidth on remote or local node as specified by the message.
Error Message%ROUTING-MPLS_TE-5-S2L_REROUTE [chars] (LSP Id: [unsigned int] Dest: [chars]) has been fast-rerouted.
Explanation The specified sub LSP has been rerouted.
Recommended Action None. This is a solicited message (by 'logging event sub-lsp reroute' interface destination configuration) and is informative only.
Error Message%ROUTING-MPLS_TE-5-S2L_UPDOWN [chars] (LSP Id: [unsigned int] Dest: [chars]) state changed to [chars]
Explanation The specified interface destination has changed operational state.
Recommended Action None. This is a solicited message (by 'logging event sub-lsp state' interface destination configuration) and is informative only.
Error Message%ROUTING-MPLS_TE-7-ERR_INTERNAL [chars] : [chars]
Explanation An internal system error occurred.
Recommended Action Copy the message exactly as it appears and report it to your technical service representative.
MRIB_API Messages
Error Message%ROUTING-MRIB_API-3-ASYNC_ERR Asynchronous error: [chars]
Explanation An unhandled asynchronous error occurred in the MRIB API.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB_API-3-CORRPT Corrupted update: [chars]. (expected [dec] bytes, got [dec] bytes)
Explanation A corrupted update was received from the MRIB by the MRIB API.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB_API-3-GEN_ERR [chars]%s
Explanation Error occurred in mrib client lib.
Recommended Action No action is required.
Error Message%ROUTING-MRIB_API-3-GENINITFAIL Initialization failed: [chars] [chars]
Explanation Error occurred at client initialization.
Recommended Action No action is required.
Error Message%ROUTING-MRIB_API-3-RPC_FAIL RPC failure: [chars]
Explanation An RPC-related error occurred in an RPC call from the MRIB API.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB_API-7-ASYNC_WAR Warning: [chars]
Explanation A recoverable error condition occurred in the MRIB API.
Recommended Action No action is required.
MRIB Messages
Error Message%ROUTING-MRIB-2-NOMEMORY [chars]No memory for [chars] in [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MRIB-2-NORESOURCE Resource unavailable for [chars] in [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MRIB-2-RC_INIT_ERR Route collapse IPC Init failed at [chars]!
Explanation The route collapse IPC could not be initialized.
Recommended Action This is a fatal error. Process does not recover currently. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-EDM_INIT Error in EDM activity : [chars] - [chars]
Explanation An error occurred when MRIB tried to initialize conn to Sysdb for show commands.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-EXTRANET_ERR [chars]
Explanation An error occurred in MRIB MVPN EXTRANET operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-GEN_ERR [chars]%s
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-GENCOMMERR Communication error: [chars] [chars]
Explanation A Inter Process Communication error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-GENINITFAIL Initialization failed: [chars] [chars]
Explanation An unrecoverable error occurred at system initialization time.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-IFCACHE_ERR [chars]
Explanation An error occurred in MRIB interface cache operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-INTERNALERR Internal error: [chars] in [chars] line [dec] ([chars])
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-LRD_ERR LRD Error: [chars] - [chars]
Explanation A general error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-LWM_ERR MRIB LWM error: [chars] - [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-MOD_INTF_LIST Interface [chars] has no modified flags. Shouldn't be present in list.
Explanation An error occurred when MRIB tried to walk the modified interfaces list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-NSF_ERR [chars]
Explanation An error occurred in MRIB NSF.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-NSFSTATE Error modifying MRIB Non-stop Forwarding state in [chars]: [chars]
Explanation An internal error occurred when MRIB attempted to transition to/from Non-stop Forwarding mode.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-PLATFORM_API_ERR [[dec]] Platform API failed to parse nodeid from ifh [hex] [err: [chars]]
Explanation Platform API failed to get node id for underlying interface.
Recommended Action No action is required.
Error Message%ROUTING-MRIB-3-RC_ERR [chars]
Explanation An error occurred in MRIB route collapse operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-REDUCEDFUNCT Initialization of [chars] functionality failed
Explanation The initialization of a functionality failed. This component might still operate without the functionality.
Recommended Action This indicate a resource shortage. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MRIB-3-TLC_ERR [chars]
Explanation An error occurred in MRIB TLC operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-3-TREE_OPER Failed to [chars] [chars] interface in interface tree of [chars].
Explanation An error occurred when MRIB tried to perform a tree operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-ADD_DEL_SAME_BATCH_ERR Tunnel entry [hex] being added and removed in same batch ([dec])
Explanation IIR sends addition and deletion of bundle member mapping in same batch
Recommended Action No action is required.
Error Message%ROUTING-MRIB-4-CLIENT_WRITE Client [CCB ID [dec]]. Update size equals [dec] bytes. [chars]
Explanation A client attempted to write an invalid update.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-DEBUGERR Debugging error: [chars] in [chars] line [dec] ([chars])
Explanation An error related to the debugging subsystem occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-FILTRVIOLERR Filter violation error: conn [dec] ([chars]:[chars]) in [chars]
Explanation A client tried to modify a route attribute not owned by it
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-GEN_WARN [chars]
Explanation A general warning occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-INCORRECTPARS Illegal parameter in function call ([chars]) in [chars]
Explanation An externally accessible function has been called with illegal parameter(s). The parameter(s) has been casted to an acceptable value.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MRIB-4-NOMEMORYW No memory for [chars] in [chars]. Handling: [chars]
Explanation The requested operation could not be accomplished because of a low memory condition but the problem has ben handled locally.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MRIB-4-STALE_HANDLE_ERR [chars]%s
Explanation A pfi query was made for a stale interface handle, possibly transient error.
Recommended Action No action is required.
Error Message%ROUTING-MRIB-5-BCDL_ERR Failed to [chars]: [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MSDP Messages
Error Message%ROUTING-MSDP-3-ACL_ERR acl error: [chars] [chars] [chars]
Explanation Check if access list is configured as intended.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MSDP-3-BAD_STATE the peer [chars] has changed to an illegal state: [dec]
Explanation The state was not one of the valid states.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-CACHE_ERR cache error: [chars] [chars]
Explanation An error occurred updating the SA cache.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-CONNECTION_ERR [chars] error: [chars]
Explanation A peer has incorrectly attempted to establish a connection with us. Possible causes may include a passive peer trying to make an active connection, in this case the connection will be rejected. Receiving a connection request from a peer that is in the Established state, in this case the current, if the peer is active, the existing connection will be terminated and the new connection will be acted upon. recommended_action: Gather as much relevant information from the respective peer.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-EDM_ERR error: show server error: [chars] [chars]
Explanation An error occurred with a show client communicating with the msdp. show server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-EVENT_FAILED event [chars] failure: [chars]
Explanation An unrecoverable error occurred during the event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-IARM_UPDATE_ERR Failed to update: [chars]
Explanation An error occurred when registering to IARM.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-INIT_FAILED Initialization failed: [chars]
Explanation An unrecoverable error occurred at system initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-INIT_FAILED2 Initialization failed: [chars], [chars]
Explanation An unrecoverable error occurred at system initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-INTERNAL_STATE_ERR [chars]: [chars] [chars]/[chars]
Explanation An error occurred due to inconsistent internal state.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-IO_FAILED I/O failure: [chars] [dec], [chars], [chars]
Explanation An error has occurred during a socket operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-ITAL_REG_ERR Failed to register on interface [chars]: [chars]
Explanation An error occurred when registering to ITAL.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-LPTS_POLICY_ERR Failed to [chars] lpts policy for peer [chars] [[dec]]
Explanation Some socket/lpts error occurred.
Recommended Action Consult the configuration documentation for appropriate commands.
Error Message%ROUTING-MSDP-3-LTRACE_INIT ltrace_init failed for '[chars]': [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-MRIB_ERR mrib error: [chars], [chars]
Explanation An error has occurred during communication with the MRIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-NOTIFY [chars] notification [chars]: code: [dec], subcode [dec]
Explanation An error was encountered during communication with specified peer.
Recommended Action Observe error details to determine cause of problem. If that does not help turn on 'debug ip msdp tlv'.
Error Message%ROUTING-MSDP-3-OUT_OF_MEMORY out of memory: [chars] [chars]
Explanation Eliminate system processes or add memory.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MSDP-3-OUT_OF_RESOURCE [chars] active SA limit [dec] exceeded SA count
Explanation Resource limit has been hit .
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-MSDP-3-SOCKET_ERR socket([dec]) error: [chars] [chars]
Explanation An unrecoverable error occurred during a socket operation.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-SYSDB_ERR sysdb error: [chars] [chars]
Explanation An error occurred while communicating with sysdb.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-WDSYSMON_EVENT_ERROR Received an invalid event from WDSysmon
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-3-WDSYSMON_REGISTER_ERROR [chars]
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-BAD_MASKLEN invalid mask length, must be 32 ([chars]/[dec]): [chars]
Explanation A masklen other than 32 was attempted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-BGP bgp client: [chars] [chars]
Explanation There is a problem communicating with BGP.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-CONFIG_FAILED config failed: [chars] [chars], [chars]
Explanation Reconfigure configured.
Recommended Action Consult the configuration documentation for appropriate commands.
Error Message%ROUTING-MSDP-4-MRIB_WARN warning mrib: [chars]: [chars]
Explanation An problem communicating with the mrib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-OOM_STATE_THROTTLE Received [chars] memory depletion warning, stop creating new msdp SA state
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-OOM_STATE_UNTHROTTLE Node memory back to normal, new msdp states will be created
Explanation Internal error occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-PEER_ERR peer error: [chars] [chars]
Explanation Some peer error occurred.
Recommended Action Consult the configuration documentation for appropriate commands.
Error Message%ROUTING-MSDP-4-RIB_ERR rib error: [chars] [chars]: [chars]
Explanation An error has occurred during communication with the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-SA_MESSAGE [chars]: error in SA ([chars], [chars]): [chars]
Explanation Error in the SA message format or contents occurred.
Recommended Action Turn on 'debug ip msdp tlv' for more information. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-4-TIMER timer error has occurred
Explanation A timer error has occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-5-INIT_PEER_UP_DOWN [chars] [chars] [chars]
Explanation MSDP Peer UP/DOWN occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-6-INIT_BASIC [chars]: pid [dec]
Explanation MSDP initialization occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-MSDP-6-INIT_INFO retried [chars] [chars] [dec]
Explanation An unrecoverable error occurred at system initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
MULTIVER Messages
Error Message%ROUTING-MULTIVER-3-ERR_DLL_OPEN Could not load DLL [chars]: [chars]
Explanation There was a problem loading the DLL. The router has run out of memory, or there was a problem reading the file.
Recommended Action Check to make sure that one or more nodes is not having problems with memory.
Error Message%ROUTING-MULTIVER-4-DLL_SIGNATURE_MISMATCH Could not locate DLL [chars]([chars]), using [chars]([chars])
Explanation There was a problem locating the DLL with matching signature - the problem is resolved by using existing dll installed on this node.
Recommended Action Check to make sure that there is no disparity in software installation across multiple nodes.
ORA_SHARED Messages
Error Message%ROUTING-ORA_SHARED-4-ERR_DLL_REG Unable to register cerrno dll [chars] because [chars]
Explanation The given cerrno dll could not be marked for use. This does not change the functionality of the system but does obscure the meaning of error codes presented by this part of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ORA Messages
Error Message%ROUTING-ORA-2-ERR_MEM_ALLOC Cannot allocate entry
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ORA-3-DUPLICATE_DOCKENTRY Dock entry add failure
Explanation Duplicate dock entry occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-INIT Failure in init function in DLL [chars]
Explanation The library is incorrectly installed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSING_BASE_TYPE The base type '[chars]' v'[chars]' was used as a [chars] in a [chars]: '[chars]' type in area [chars]
Explanation One of the operations in one of the ORAs used a base type that was not defined in any of the ORA math sets.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSING_FUNCTION Route access library [chars] has no [chars] function
Explanation The library is incorrectly installed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSING_OPERATOR The operator '[chars]' was not located in any of the '[chars]'s ORAs.
Explanation There is a function declared within the various docked ORAs at this attach point that uses an operator that does not exist with the same set of docked ORAs. Please contact support.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-THREADING Threading operation '[chars]' for '[chars]' failed because: [chars]
Explanation The presented threading operation failed. It is likely that policy multi-version calls will stop working and thus policy may not be operational.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-4-ERR_DLL_REG Unable to register cerrno dll [chars] because [chars]
Explanation The given cerrno dll could not be marked for use. This does not change the functionality of the system but does obscure the meaning of error codes presented by this part of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-4-MERGE_FAILED Some base type(s) was(were) unavailable during AP merging at: [chars]
Explanation One or more base types where not available when bringing together the parts of this attach point. This is an item that should be caught during testing. If it does show up, support should be contacted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-4-MISSING_DOCK_INFO The dock data for docking item [chars] was missing
Explanation This is most likely an internal logic error that resulted in a given ora docking being released more than once.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-7-DBGINIT Unable to bring up debug event structures: [chars]
Explanation The debug event initialization failed. The ora docker will still run correctly, but debug commands may be unavailable.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-7-DBGSHUTDOWN Unable to shutdown debug event structures: [chars]
Explanation The debug event shutdown failed. The ora docker will still run correctly, but debug commands may be unavailable.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPF_EDM Messages
Error Message%ROUTING-OSPF_EDM-3-DATALIST_ADD_FAILED Failed to add an external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-DATALIST_CREATE_FAILED Failed to create external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-DATALIST_SET_MORE_FLAG Failed to set external data manager more flag for datalist [chars]
Explanation A client has requested information through SysDB from OSPF. During execution of the request an attempt to set a flag indicating there is more data for the client failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-ENCODE_FAILED Failed to encode [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-LIST_ADD_FAILED Failed to add to an external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-LIST_CREATE_FAILED Failed to create external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-SYSDB_BIND_FAILED Failed to connect to SysDB ([chars])
Explanation The process failed to connect to SysDB while starting.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPF_POLICY Messages
Error Message%ROUTING-OSPF_POLICY-3-ORA_INSTBUILD Failed to build [chars], reason [chars] cer [chars]
Explanation Internal error in policy library occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_POLICY-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in policy library occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPF_RIB Messages
Error Message%ROUTING-OSPF_RIB-3-ERR_PATH_ADD Error adding path to batching buffer for [chars]/[dec], data len [dec], max msg len [dec], max buf len [dec]
Explanation An error was encountered in the call to ipv4_rib_batch_add_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_PATH_DELETE Error deleting path from batching buffer for [chars]/[dec], data len [dec], max msg len [dec], max buf len [dec]
Explanation An error was encountered in the call to ipv4_rib_batch_delete_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_PROTO_MODIFY Error changing purgetime
Explanation An error was encountered in the call to ipv4_rib_protocol_modify.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_ROUTE_HDR Error adding route header to batching buffer for [chars]/[dec], data len [dec], max msg len [dec], max buf len [dec]
Explanation An error was encountered in the call to ipv4_rib_batch_add_route.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_UPDATE_DONE Error informing rib that batch is complete
Explanation An error was encountered in the call to ipv4_rib_batch_complete.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-4-BATCH_LOG_PATH RIB batch error, [chars] (result [dec]), prefix [hex]/[dec] next_hop [hex] intf [chars]. Retrying
Explanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-5-BATCH_ERROR RIB batch error, [chars]
Explanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-5-BATCH_ERROR_CODE RIB batch error, [chars] ([hex])
Explanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-6-INFO_RT_HDR_NOTUSED Believes [chars]/[dec] and [chars]/[dec] differ
Explanation The RIB batching API believes that it already has this router header in the batching buffer.
Recommended Action No action is required.
OSPF_UV Messages
Error Message%ROUTING-OSPF_UV-3-CERR_REG_FAIL Failed to register internal error codes: [chars]
Explanation An error occurred during the registration of OSPF error codes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_DBG_REGISTER_FAILED Error initializing ospf_uv debugging: [chars]
Explanation An error occurred during initialization of the ospf_uv process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_MEM_ALLOC_FAIL Unable to allocate [unsigned int] bytes for '[chars]'
Explanation The ospf_uv process was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_PROC_READY Error signaling process ready: [chars]
Explanation The ospf_uv process was unable to signal process ready to sysmgr.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_CONNECT Error binding to SysDB: [chars]
Explanation The ospf_uv process was unable to bind to SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_DISCONNECT Error unbinding from SysDB: [chars]
Explanation The ospf_uv process was unable to unbind from SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_REG_VERIFY Error registering with SysDB: [chars]
Explanation The ospf_uv process was unable to register with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_VRFN_FNS_INIT Error setting SysDB callback functions: [chars]
Explanation The ospf_uv process was unable to initialize SysDB callbacks.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-EVENT_ERR Error in event loop: [chars]
Explanation An error occurred in the main ospf_uv event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-EVM_CRE_FAIL Error creating event connection manager: [chars]
Explanation The ospf_uv process was unable to create an event connection manager instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-INTF_FWS_INIT Error initializing forward-reference store: [chars]
Explanation The ospf_uv process was unable to initialize the forward-reference store library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-6-PROCESS_NAME Caution: The OSPF process name [chars] conflicts with a show or clear command name
Explanation The name chosen for the OSPF process matches an ospf show or clear command, or a command abbreviation. This can cause ambiguities with subsequent show or clear commands for this process.
Recommended Action Choose a different name for the OSPF process.
OSPF Messages
Error Message%ROUTING-OSPF-2-ERR_MEM_ALLOC No memory, [chars], process terminated
Explanation Memory allocation of a critical OSPF resource failed because of a low memory condition. The OSPF process was terminated.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-OSPF-3-ALLOC_ERR Allocation error, [unsigned int] bytes for [chars]
Explanation Allocation of the specified resource failed because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands.
Error Message%ROUTING-OSPF-3-AREANULL --
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-BADMSG ospf router received bad message type [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-BADSHARE Bad refcount at [hex] (refcount equals [hex]) in [chars]
Explanation An internal software error occurred. Resources may be in inconsistent state.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-OSPF-3-BADTIMER Managed Timer error, [chars]: Unrecognized timer type [dec]
Explanation A timer was found with an unrecognized type occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-DBGINIT Debug init error, [chars]: event [chars], error [dec]
Explanation Failure to initialize a debugging flag occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-DUP_RTRID OSPF detected duplicate router-id [chars] from [chars] on interface [chars]
Explanation OSPF received hello packet from a neighbor which has the same router-id as this routing process. A full adjacency cannot be established.
Recommended Action OSPF router-id should be unique. Change the neighbors router-id.
Error Message%ROUTING-OSPF-3-ERR_RESOURCE_ALLOC No memory could be allocated for the resource, [chars]
Explanation Allocation of the specified resource failed because of a low memory condition. This could affect the protocol functionality.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands and preferably restart the OSPF process.
Error Message%ROUTING-OSPF-3-EVM External Event Manager error, [chars], error [chars] [[hex]]
Explanation A call to an external event manager function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EVM_CODE External Event Manager error, [chars]: [chars] code [dec], error [chars] [[hex]]
Explanation A call to an external event manager function failed. The impact of this error is insignificant, unless the error condition persists for a duration close to the minimal DeadInterval used over all OSPF interfaces.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EVM_RL raw_conn momentarily not usable, [chars]
Explanation raw_conn is not available to send the packet.
Recommended Action If the condition persist, contact the technical support.
Error Message%ROUTING-OSPF-3-EXTERNALERR External error, [chars]
Explanation An external software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EXTERNALERR_RC External error, [chars], error [hex]
Explanation An external software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-FRIS FRIS error, [chars], [chars] error [chars] [[hex]]
Explanation The FRIS request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IDBERR IDB error, [chars]: [chars], intf [chars] cerr [chars]
Explanation Error encountered while attempting to activate an idb. Problem could be corrupt data from IM or IP/ARM or the FRIS.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFCHECK Interface [chars] is attached to more than one area
Explanation An internal consistency check has failed. An interface appears to be associated with more than one area.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFINIT Interface init error, interface [chars]
Explanation OSPF failed to initialize data structures for an interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFMGR External IFMGR error, [chars], intf [chars] error [chars] [[hex]]
Explanation The specified interface manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IGPTE IGP/TE error, [chars]: [chars] error [dec]
Explanation Error encountered while attempting to use the IGP_TE Lib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INIT_ERR Init error, [chars], error [hex]
Explanation An error occurred during initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INIT_ERR_STR Initialization failure, [chars], error [chars], process terminated
Explanation An error occurred during initialization, causing the process to terminate.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-OSPF-3-INTERNALERR Internal error, [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INTERNALERR_RC Internal error, [chars], error [hex]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IPARM External IP-ARM error, [chars], error [chars] [[hex]]
Explanation A call to an external IP-ARM function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-LWM External light-weight msg error, [chars], error [chars] [[hex]]
Explanation A call to an external light-weight messaging function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the