Cisco IOS XR System Error Message Reference Guide, Release 4.0 - Access Control List (ACL) Messages [Cisco IOS XR Software (End-of-Sale)]

Table Of Contents

Access Control List (ACL) Messages

APPS_ES_ACLMGR Messages

ES_ACL Messages

IP_ACL_PARSE Messages

IPV4_ACL Messages

IPV6_ACL_DAEMON Messages

IPV6_ACL_LTRACE Messages

IPV6_ACL Messages

LI Messages

PFILTER_NETIO_LTRACE Messages

Access Control List (ACL) Messages

This section contains all ACL related System Error Messages.

APPS_ES_ACLMGR Messages
Error Message     
%ACL-APPS_ES_ACLMGR-7-ERROR [chars]
Explanation This is simply a debug message. If any severe errors occur the process will exit and will be restarted by the sysmgr.
Recommended Action None

ES_ACL Messages
Error Message     
%ACL-ES_ACL-6-ESACCESSLOGV access-list [chars] ([dec]) [chars] [hex] Outer vlan [dec] dei [dec] cos [dec] inner vlan [dec] dei [dec] cos [dec] [chars] - [chars], [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected. It has both outer and inner vlan. These messages are issued whenever access lists are configured with the 'log' option. Any access list entry that has had hits are logged via this message. These messages are issued either at 5 minute intervals, or whenever the log buffer overflows.
Recommended Action None

IP_ACL_PARSE Messages
Error Message    
%ACL-IP_ACL_PARSE-7-ERR_MEM_ALLOC Unable to allocate memory for [chars]
Explanation Memory allocation failed, probably due to memory depletion. An entry could not be added to the cache, the associated command will be blocked by the parser.
Recommended Action None
Error Message     
%ACL-IP_ACL_PARSE-7-ERR_THREAD_MUTEX_LOCK Unable to lock cache mutex. Error: [chars]
Explanation A mutex is used to protect the ACL and Prefix List caches. An attempt to lock a mutex failed with the error reported.
Recommended Action Abort the configuration operation and restart the parser server.

IPV4_ACL Messages
Error Message     
%ACL-IPV4_ACL-6-IPACCESSLOGDP access-list [chars] ([dec]) [chars] [chars] [chars] [chars]- [chars] ([dec]/[dec]), [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type ICMP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV4_ACL-6-IPACCESSLOGDP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars] ([dec]/[dec]), [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type ICMP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV4_ACL-6-IPACCESSLOGNP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type other than TCP, UDP, SCTP, IGMP, ICMP and 'standard ACL'. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV4_ACL-6-IPACCESSLOGNP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type other than TCP, UDP, SCTP, IGMP, ICMP and 'standard ACL'. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV4_ACL-6-IPACCESSLOGP access-list [chars] ([dec]) [chars] [dec] [chars]([dec]) [chars]- [chars]([dec]), [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type TCP (or) UDP (or) SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV4_ACL-6-IPACCESSLOGP access-list [chars] ([dec]) [chars] [chars] [chars]([dec]) [chars]- [chars]([dec]), [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type TCP (or) UDP (or) SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV4_ACL-6-IPACCESSLOGRP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type IGMP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV4_ACL-6-IPACCESSLOGRP access-list [chars] ([dec]) [chars] [chars] [chars] [chars]- [chars], [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type IGMP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV4_ACL-6-IPACCESSLOGS access-list [chars] ([dec]) [chars] [chars] [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the access-list that is used by routing protocols. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV4_ACL-6-IPACCESSLOGS access-list [chars] ([dec]) [chars] [chars] [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the access-list that is used by routing protocols. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV4_ACL-7-INIT IPv4 ACL Manager initialisation failed in function [chars]: [chars]
Explanation The ACL manager process encountered the specified error while initializing the specified facility. If this error occurs, the sysmgr process will restart the ACL manager process. This failure will occur only on RP.
Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the gathered information with this error message text. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%ACL-IPV4_ACL-7-IPACCESSPTHREAD failed to [chars] ACL mutex, error [[dec]]: [chars]
Explanation The mutex used to protect access to the ACL data structure could not be locked or unlocked. The error message will include details of the particular failure. Possible causes of failure are the mutex is corrupted, has not been initialized or is being accessed recursively (this is not allowed). Because the mutex could not be used the process may restart to recover from the failure.
Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%ACL-IPV4_ACL-7-IPACCESSPTHREAD failed to [chars] ACL mutex, error [[dec]]: [chars]
Explanation The mutex used to protect access to the ACL data structure could not be locked or unlocked. The error message will include details of the particular failure. Because the mutex could not be used the process was restarted to recover from the failure.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

IPV6_ACL_DAEMON Messages
Error Message     
%ACL-IPV6_ACL_DAEMON-7-INIT Failed to initialize [chars], because of [chars]
Explanation Initialization failed. Both the initialization type and the error code are displayed. The sysmgr process will restart the IPv6 daemon if this condition happens.
Recommended Action None

IPV6_ACL_LTRACE Messages
Error Message     
%ACL-IPV6_ACL_LTRACE-3-INIT ltrace_init failed for '[chars]': [chars]
Explanation Initialization of LTRACE failed for ipv6_acl. The error code is displayed. This failure does not impact the major functionality. This failure may occur on RP or LC.
Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

IPV6_ACL Messages
Error Message     
%ACL-IPV6_ACL-1-IPACCESSDLLOPEN failed to open dll: [chars]
Explanation This message is seen when the process fails to open the DLL 'libipv6_acl_tree.dll'. This failure may occur on RP and LC. It may fail to open the DLL due to any one of the following reasons: 1. passing the bad mode like no share mode(RTLD_NOSHARE) 2. list of DLL objects is empty or the list itself doesn't exits. 3. if no symbol in executable. 4. if the memory allocation fails at any stage 5. if the dll is not unique with respect to the other DLL's loaded and placed in the list.
Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%ACL-IPV6_ACL-1-IPACCESSDLLOPEN failed to open dll: [chars]
Explanation This message is seen when the process fails to open the DLL 'libipv6_acl_tree.dll'. This failure may occur on RP and LC. It may fail to open the DLL due to any one of the following reasons: 1. passing the bad mode like no share mode(RTLD_NOSHARE) 2. list of DLL objects is empty or the list itself doesn't exits. 3. if no symbol in executable. 4. if the memory allocation fails at any stage 5. if the dll is not unique with respect to the other DLL's loaded and placed in the list.
Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%ACL-IPV6_ACL-1-IPACCESSDLSYM dlsym lookup for ipv6_acl_api_functions failed for dll: [chars]
Explanation This message is seen when there is no symbol present with the specified name in the corresponding list of objects for the DLL opened.
Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%ACL-IPV6_ACL-1-IPACCESSDLSYM dlsym lookup for ipv6_acl_api_functions failed for dll: [chars]
Explanation This message is seen when there is no symbol present with the specified name in the corresponding list of objects for the DLL opened.
Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%ACL-IPV6_ACL-1-IPACCESSNOMEM insufficient memory for dll: [chars]
Explanation there is no sufficient memory available to load the specified dll.
Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%ACL-IPV6_ACL-1-IPACCESSNOMEM insufficient memory for dll: [chars]
Explanation there is no sufficient memory available to load the specified dll.
Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%ACL-IPV6_ACL-3-IPACCESSPTHREAD failed to [chars] ACL mutex, error [[dec]]: [chars]
Explanation The mutex used to protect access to the ACL data structure could not be locked or unlocked. The error message will include details of the particular failure. Possible causes of failure are the mutex is corrupted, has not been initialized or is being accessed recursively (this is not allowed). Because the mutex could not be used the process may restart to recover from the failure.
Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%ACL-IPV6_ACL-3-IPACCESSPTHREAD failed to [chars] ACL mutex, error [[dec]]: [chars]
Explanation The mutex used to protect access to the ACL data structure could not be locked or unlocked. The error message will include details of the particular failure. Possible causes of failure are the mutex is corrupted, has not been initialized or is being accessed recursively (this is not allowed). Because the mutex could not be used the process may restart to recover from the failure.
Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%ACL-IPV6_ACL-6-IPACCESSLOGDP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars] ([dec]/[dec]), [dec] packet[chars]
Explanation Packet matching the log criteria for the given access list was detected.
Recommended Action No action is required.
Error Message     
%ACL-IPV6_ACL-6-IPACCESSLOGDP access-list [chars] ([dec]) [chars] [chars] [chars] [chars]- [chars] ([dec]/[dec]), [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected.
Recommended Action No action is required.
Error Message     
%ACL-IPV6_ACL-6-IPACCESSLOGNP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars]
Explanation These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type other than TCP, UDP, SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV6_ACL-6-IPACCESSLOGNP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars]
Explanation Packet matching the log criteria for the given access list was detected. These messages are issued when the IP protocol type is other than TCP, UDP and SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV6_ACL-6-IPACCESSLOGP access-list [chars] ([dec]) [chars] [dec] [chars]([dec]) [chars]- [chars]([dec]), [dec] packet[chars]
Explanation Packet matching the log criteria for the given access list was detected. These messages are issued when the IP protocol type is TCP or UDP or SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV6_ACL-6-IPACCESSLOGP access-list [chars] ([dec]) [chars] [chars] [chars]([dec]) [chars]- [chars]([dec]), [dec] packet[chars]
Explanation These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type TCP (or) UDP (or) SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647).
Recommended Action This is information only message, no action required No action is required.
Error Message     
%ACL-IPV6_ACL-6-IPACCESSLOGRP access-list [chars] ([dec]) [chars] [chars] [chars] [chars]- [chars], [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected.
Recommended Action No action is required.
Error Message     
%ACL-IPV6_ACL-6-IPACCESSLOGRP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected.
Recommended Action No action is required.
Error Message     
%ACL-IPV6_ACL-6-IPACCESSLOGS access-list [chars] ([dec]) [chars] [chars] [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected.
Recommended Action No action is required.
Error Message     
%ACL-IPV6_ACL-6-IPACCESSLOGS access-list [chars] ([dec]) [chars] [chars] [dec] packet[chars]
Explanation A packet matching the log criteria for the given access list was detected.
Recommended Action No action is required.

LI Messages
Error Message     
%ACL-LI-3-ERROR [chars]: [chars]: ([dec])[chars]
Explanation The LI Netio thread encountered the specified error while initializing the specified facility. If this error occurs, the LawfulIntercept thread will exit.
Recommended Action None

PFILTER_NETIO_LTRACE Messages
Error Message     
%ACL-PFILTER_NETIO_LTRACE-7-INIT ltrace_init failed for '[chars]': [chars]
Explanation    Initialization failed. Both the initialization type and the error code are displayed. The sysmgr process will restart the ipv4_aclmgr if this condition happens.
Recommended Action    None
Recommended Action

	Cisco IOS XR System Error Message Reference Guide, Release 4.0
	Access Control List (ACL) Messages
Cisco IOS XR System Error Message Reference Guide, Release 4.0 Preface Overview Access Control List (ACL) Messages Application Infrastructure Messages Diagnostic Messages Fabric Messages Forwarding Messages High Availability (HA) Messages Infrastructure Messages Installation Messages Internet Protocol (IP) Messages Layer 1 Messages Layer 2 Messages Layer 3 Messages License Messages Media Messages Manageability (MGBL) Messages Operating System (OS) Messages Packet Infrastructure Messages Platform Messages Policy Manager Messages Quality of Service (QoS) Messages Routing Messages Security Messages Services Messages Simple Network Management Protocol (SNMP) Messages Subscriber Messages	Download this chapter Access Control List (ACL) Messages Download the complete book Full Book PDF: Cisco IOS XR System Error Message Reference Guide, Release 4.0 (PDF - 51 MB) Feedback Table Of Contents Access Control List (ACL) Messages APPS_ES_ACLMGR Messages ES_ACL Messages IP_ACL_PARSE Messages IPV4_ACL Messages IPV6_ACL_DAEMON Messages IPV6_ACL_LTRACE Messages IPV6_ACL Messages LI Messages PFILTER_NETIO_LTRACE Messages Access Control List (ACL) Messages This section contains all ACL related System Error Messages. APPS_ES_ACLMGR Messages Error Message %ACL-APPS_ES_ACLMGR-7-ERROR [chars] Explanation This is simply a debug message. If any severe errors occur the process will exit and will be restarted by the sysmgr. Recommended Action None ES_ACL Messages Error Message %ACL-ES_ACL-6-ESACCESSLOGV access-list [chars] ([dec]) [chars] [hex] Outer vlan [dec] dei [dec] cos [dec] inner vlan [dec] dei [dec] cos [dec] [chars] - [chars], [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. It has both outer and inner vlan. These messages are issued whenever access lists are configured with the 'log' option. Any access list entry that has had hits are logged via this message. These messages are issued either at 5 minute intervals, or whenever the log buffer overflows. Recommended Action None IP_ACL_PARSE Messages Error Message %ACL-IP_ACL_PARSE-7-ERR_MEM_ALLOC Unable to allocate memory for [chars] Explanation Memory allocation failed, probably due to memory depletion. An entry could not be added to the cache, the associated command will be blocked by the parser. Recommended Action None Error Message %ACL-IP_ACL_PARSE-7-ERR_THREAD_MUTEX_LOCK Unable to lock cache mutex. Error: [chars] Explanation A mutex is used to protect the ACL and Prefix List caches. An attempt to lock a mutex failed with the error reported. Recommended Action Abort the configuration operation and restart the parser server. IPV4_ACL Messages Error Message %ACL-IPV4_ACL-6-IPACCESSLOGDP access-list [chars] ([dec]) [chars] [chars] [chars] [chars]- [chars] ([dec]/[dec]), [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type ICMP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV4_ACL-6-IPACCESSLOGDP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars] ([dec]/[dec]), [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type ICMP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV4_ACL-6-IPACCESSLOGNP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type other than TCP, UDP, SCTP, IGMP, ICMP and 'standard ACL'. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV4_ACL-6-IPACCESSLOGNP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type other than TCP, UDP, SCTP, IGMP, ICMP and 'standard ACL'. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV4_ACL-6-IPACCESSLOGP access-list [chars] ([dec]) [chars] [dec] [chars]([dec]) [chars]- [chars]([dec]), [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type TCP (or) UDP (or) SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV4_ACL-6-IPACCESSLOGP access-list [chars] ([dec]) [chars] [chars] [chars]([dec]) [chars]- [chars]([dec]), [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type TCP (or) UDP (or) SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV4_ACL-6-IPACCESSLOGRP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type IGMP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV4_ACL-6-IPACCESSLOGRP access-list [chars] ([dec]) [chars] [chars] [chars] [chars]- [chars], [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type IGMP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV4_ACL-6-IPACCESSLOGS access-list [chars] ([dec]) [chars] [chars] [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the access-list that is used by routing protocols. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV4_ACL-6-IPACCESSLOGS access-list [chars] ([dec]) [chars] [chars] [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. These messages are issued whenever access lists are configured with the 'log' option and matches with the access-list that is used by routing protocols. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV4_ACL-7-INIT IPv4 ACL Manager initialisation failed in function [chars]: [chars] Explanation The ACL manager process encountered the specified error while initializing the specified facility. If this error occurs, the sysmgr process will restart the ACL manager process. This failure will occur only on RP. Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the gathered information with this error message text. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %ACL-IPV4_ACL-7-IPACCESSPTHREAD failed to [chars] ACL mutex, error [[dec]]: [chars] Explanation The mutex used to protect access to the ACL data structure could not be locked or unlocked. The error message will include details of the particular failure. Possible causes of failure are the mutex is corrupted, has not been initialized or is being accessed recursively (this is not allowed). Because the mutex could not be used the process may restart to recover from the failure. Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %ACL-IPV4_ACL-7-IPACCESSPTHREAD failed to [chars] ACL mutex, error [[dec]]: [chars] Explanation The mutex used to protect access to the ACL data structure could not be locked or unlocked. The error message will include details of the particular failure. Because the mutex could not be used the process was restarted to recover from the failure. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. IPV6_ACL_DAEMON Messages Error Message %ACL-IPV6_ACL_DAEMON-7-INIT Failed to initialize [chars], because of [chars] Explanation Initialization failed. Both the initialization type and the error code are displayed. The sysmgr process will restart the IPv6 daemon if this condition happens. Recommended Action None IPV6_ACL_LTRACE Messages Error Message %ACL-IPV6_ACL_LTRACE-3-INIT ltrace_init failed for '[chars]': [chars] Explanation Initialization of LTRACE failed for ipv6_acl. The error code is displayed. This failure does not impact the major functionality. This failure may occur on RP or LC. Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. IPV6_ACL Messages Error Message %ACL-IPV6_ACL-1-IPACCESSDLLOPEN failed to open dll: [chars] Explanation This message is seen when the process fails to open the DLL 'libipv6_acl_tree.dll'. This failure may occur on RP and LC. It may fail to open the DLL due to any one of the following reasons: 1. passing the bad mode like no share mode(RTLD_NOSHARE) 2. list of DLL objects is empty or the list itself doesn't exits. 3. if no symbol in executable. 4. if the memory allocation fails at any stage 5. if the dll is not unique with respect to the other DLL's loaded and placed in the list. Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %ACL-IPV6_ACL-1-IPACCESSDLLOPEN failed to open dll: [chars] Explanation This message is seen when the process fails to open the DLL 'libipv6_acl_tree.dll'. This failure may occur on RP and LC. It may fail to open the DLL due to any one of the following reasons: 1. passing the bad mode like no share mode(RTLD_NOSHARE) 2. list of DLL objects is empty or the list itself doesn't exits. 3. if no symbol in executable. 4. if the memory allocation fails at any stage 5. if the dll is not unique with respect to the other DLL's loaded and placed in the list. Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %ACL-IPV6_ACL-1-IPACCESSDLSYM dlsym lookup for ipv6_acl_api_functions failed for dll: [chars] Explanation This message is seen when there is no symbol present with the specified name in the corresponding list of objects for the DLL opened. Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %ACL-IPV6_ACL-1-IPACCESSDLSYM dlsym lookup for ipv6_acl_api_functions failed for dll: [chars] Explanation This message is seen when there is no symbol present with the specified name in the corresponding list of objects for the DLL opened. Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %ACL-IPV6_ACL-1-IPACCESSNOMEM insufficient memory for dll: [chars] Explanation there is no sufficient memory available to load the specified dll. Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %ACL-IPV6_ACL-1-IPACCESSNOMEM insufficient memory for dll: [chars] Explanation there is no sufficient memory available to load the specified dll. Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %ACL-IPV6_ACL-3-IPACCESSPTHREAD failed to [chars] ACL mutex, error [[dec]]: [chars] Explanation The mutex used to protect access to the ACL data structure could not be locked or unlocked. The error message will include details of the particular failure. Possible causes of failure are the mutex is corrupted, has not been initialized or is being accessed recursively (this is not allowed). Because the mutex could not be used the process may restart to recover from the failure. Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %ACL-IPV6_ACL-3-IPACCESSPTHREAD failed to [chars] ACL mutex, error [[dec]]: [chars] Explanation The mutex used to protect access to the ACL data structure could not be locked or unlocked. The error message will include details of the particular failure. Possible causes of failure are the mutex is corrupted, has not been initialized or is being accessed recursively (this is not allowed). Because the mutex could not be used the process may restart to recover from the failure. Recommended Action Please get the information specified under the component required_info and call your Cisco technical support representative and provide the representative with the gathered information with this error message text. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %ACL-IPV6_ACL-6-IPACCESSLOGDP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars] ([dec]/[dec]), [dec] packet[chars] Explanation Packet matching the log criteria for the given access list was detected. Recommended Action No action is required. Error Message %ACL-IPV6_ACL-6-IPACCESSLOGDP access-list [chars] ([dec]) [chars] [chars] [chars] [chars]- [chars] ([dec]/[dec]), [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. Recommended Action No action is required. Error Message %ACL-IPV6_ACL-6-IPACCESSLOGNP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars] Explanation These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type other than TCP, UDP, SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV6_ACL-6-IPACCESSLOGNP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars] Explanation Packet matching the log criteria for the given access list was detected. These messages are issued when the IP protocol type is other than TCP, UDP and SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV6_ACL-6-IPACCESSLOGP access-list [chars] ([dec]) [chars] [dec] [chars]([dec]) [chars]- [chars]([dec]), [dec] packet[chars] Explanation Packet matching the log criteria for the given access list was detected. These messages are issued when the IP protocol type is TCP or UDP or SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV6_ACL-6-IPACCESSLOGP access-list [chars] ([dec]) [chars] [chars] [chars]([dec]) [chars]- [chars]([dec]), [dec] packet[chars] Explanation These messages are issued whenever access lists are configured with the 'log' option and matches with the IP protocol type TCP (or) UDP (or) SCTP. This message is seen for the first match and for each match after the hit count is greater than 0x7FFFFFFF(2147483647). Recommended Action This is information only message, no action required No action is required. Error Message %ACL-IPV6_ACL-6-IPACCESSLOGRP access-list [chars] ([dec]) [chars] [chars] [chars] [chars]- [chars], [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. Recommended Action No action is required. Error Message %ACL-IPV6_ACL-6-IPACCESSLOGRP access-list [chars] ([dec]) [chars] [dec] [chars] [chars]- [chars], [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. Recommended Action No action is required. Error Message %ACL-IPV6_ACL-6-IPACCESSLOGS access-list [chars] ([dec]) [chars] [chars] [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. Recommended Action No action is required. Error Message %ACL-IPV6_ACL-6-IPACCESSLOGS access-list [chars] ([dec]) [chars] [chars] [dec] packet[chars] Explanation A packet matching the log criteria for the given access list was detected. Recommended Action No action is required. LI Messages Error Message %ACL-LI-3-ERROR [chars]: [chars]: ([dec])[chars] Explanation The LI Netio thread encountered the specified error while initializing the specified facility. If this error occurs, the LawfulIntercept thread will exit. Recommended Action None PFILTER_NETIO_LTRACE Messages Error Message %ACL-PFILTER_NETIO_LTRACE-7-INIT ltrace_init failed for '[chars]': [chars] Explanation Initialization failed. Both the initialization type and the error code are displayed. The sysmgr process will restart the ipv4_aclmgr if this condition happens. Recommended Action None Recommended Action
	Terms & Conditions \| Privacy Statement \| Cookie Policy \| Trademarks