Table Of Contents

SIP Configuration Flexibility

Contents

Restrictions for Implementing SIP Configuration Flexibility

Information About SIP Configuration Flexibility

OPTIONS Support

Restrictions for OPTIONS Support

Rewriting From Header on Non-Register Requests

Restrictions for Rewriting From Header on Non-REGISTER Requests

Rewriting To Header on Non-REGISTER Requests

Auto-detecting NAT

Restrictions for Auto-detecting NAT

Routing on Wildcard Domains

Restrictions for Auto-detecting NAT

How to Implement SIP Configuration Flexibility

Implementing SIP Configuration Flexibility

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

SIP Configuration Flexibility

---

The SBC offers flexibility in configuring the following features of a SIP adjacency:

•OPTIONS Support

•Rewriting From Header on Non-REGISTER requests

•Rewriting To Header on Non-REGISTER requests

•Auto-detecting NAT

•Routing on wildcard domains

Feature History for SIP Configuration Flexibility

Release	Modification
Release 3.5.1	This feature was introduced on Cisco XR 12000 Series Router.
Release 3.6.0	No modification.

Contents

This module contains the following sections:

•Restrictions for Implementing SIP Configuration Flexibility

•Information About SIP Configuration Flexibility

•How to Implement SIP Configuration Flexibility

•Additional References

Restrictions for Implementing SIP Configuration Flexibility

The restrictions for implementing SIP configuration flexibility are listed per feature in this chapter.

Information About SIP Configuration Flexibility

OPTIONS Support

By default, the SBC blocks the OPTIONS method from passing through. But users can now configure the SBC on a per-adjacency basis to pass or block the passthrough of the OPTIONS method. If you configure the SBC with method whitelist profiles per adjacency, then the SBC allows the OPTIONS method to pass through. If you configure the SBC with method blacklist profiles per adjacency, then the SBC blocks the OPTIONS method from being passed through.

Restrictions for OPTIONS Support

•The SBC strips out SDP blocks from messages when it allows the OPTIONS method to pass through. This limits what the SIP endpoints can exchange.

•The SBC-SIG does not send the Accept and Allow headers on any methods, including OPTIONS.

•The SBC allows only the 100Rel and Replaces tags of the Supported header to pass through, while the other tags of this header are controlled by whitelists and blacklists.

Rewriting From Header on Non-Register Requests

With this feature, users can configure the SBC on a per-adjacency basis to control whether it rewrites the hostport section of the From header on Non-Register Requests to the outbound SIP adjacency address or port. If the SBC is configured to allow the From header to pass through without it being rewritten, then the SBC allows the entire header to pass through without changing it. The only exception occurs with the Tag parameter; the SBC assigns a different value to this parameter before passing it through.

Restrictions for Rewriting From Header on Non-REGISTER Requests

•This feature is not applicable for REGISTER requests.

•This feature may only work limitedly with the Rewrite-Register feature.

•If the From header contains a Tel URI, then the SBC does not rewrite the header since it does not have a hostport.

•Depending on the number of headers, options and SIP whitelist profiles, the SBC limits the size of the From header that it allows to pass through to approximately 1000 bytes.

Rewriting To Header on Non-REGISTER Requests

With this feature, users can configure the SBC on a per-adjacency basis to control whether it rewrites the stopper section of the To header on Non-Register Requests to the outbound SIP adjacency address or port. When configured to rewrite the To headers, the SBC rewrites them to match the outgoing Request URI.

Auto-detecting NAT

With the addition of a new configuration field to the SIP adjacency, it is now possible for users to specify if the SBC must auto-detect whether a NAT is in use on that adjacency. If the SBC is configured to auto-detect NAT, then for each request that it receives, the SBC determines whether a NAT is in use for that endpoint. If the SBC determines that NAT is in use, then the SBC stores the bindings for that request and uses them when sending a response. Additionally, the SBC stores and reuses bindings for REGISTER requests for subsequent Dialog-forming and Out-of-dialog requests.

Restrictions for Auto-detecting NAT

•The SBC can auto-detect NAT only by comparing the Sent-by stopper in the Via header with the remote address and port of the message.

•If the stopper contains a domain name, instead of an IP address, the SBC cannot auto-detect whether NAT is in use. In this case, the SBC assumes that NAT is in use.

•Auto-detecting NAT is applied only to Out-of-dialog requests or Dialog-forming requests.

Routing on Wildcard Domains

The SBC routing policy allows you to use the * character in a text domain name match string. This character can match any number of characters in the called address. For example, *domain.com can match both sip1.domain.com and sip2.domain.com.

Restrictions for Auto-detecting NAT

•You can only specify one wildcard character in a given match string.

•This feature applies only to text domain name match rules, and not to dialed digit match rules.

How to Implement SIP Configuration Flexibility

This section contains the steps for implementing SIP configuration flexibility.

Implementing SIP Configuration Flexibility

SUMMARY STEPS

1. configure

2. sbc service-name

3. sbe

4. adjacency sip adjacency-name

5. passthrough from header

6. passthrough to header

7. nat force on

8. commit

9. exit

DETAILED STEPS

	Command or Action	Purpose
Step 1	configure Example: RP/0/0/CPU0:router# configure	Enables global configuration mode.
Step 2	sbc service-name Example: RP/0/0/CPU0:router(config)# sbc mysbc	Enters the mode of an SBC service. •Use the service-name argument to define the name of the service.
Step 3	sbe Example: RP/0/0/CPU0:router(config-sbc)# sbe	Enters the mode of the signaling border element (SBE) function of the SBC.
Step 4	adjacency sip sipadj Example: RP/0/0/CPU0:router(config-sbc-sbe)# adjacency sip sipadj	Enters the mode of an SBE SIP adjacency. •Use the adjacency-name argument to define the name of the SIP adjacency.
Step 5	passthrough from header Example: RP/0/0/CPU0:router(config-sbc-sbe-sip-adj)# passthrough from header	Configures the SIP adjacency to disable From rewrite.
Step 6	passthrough to header Example: RP/0/0/CPU0:router(config-sbc-sbe-sip-adj)# passthrough to header	Configures the SIP adjacency to disable To rewrite.
Step 7	nat force-on Example: RP/0/0/CPU0:router(config-sbc-sbe-sip-adj)# nat force-on	Configures the SIP adjacency to assume that all endpoints are behind a NAT device. To configure the SIP adjacency to assume that all endpoints are behind a NAT device, use the nat force-off command. By default, the SBC autodetects whether the endpoints are behind a NAT device.
Step 8	commit Example: RP/0/0/CPU0:router(config-sbc-sbe-sip-adj)# commit	Saves configuration changes. Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.
Step 9	exit Example: RP/0/0/CPU0:router(config-sbc-sbe-sip-adj)# exit	Exits the adj-sip mode and returns to the SBE mode.

Additional References

The following sections provide references related to SIP configuration flexibility on the SBC.

Related Documents

Related Topic	Document Title
Cisco IOS XR master command reference	Cisco IOS XR Master Commands List
Cisco IOS XR SBC interface configuration commands	Cisco IOS XR Session Border Controller Command Reference
Initial system bootup and configuration information for a router using the Cisco IOS XR Software	Cisco IOS XR Getting Started Guide
Cisco IOS XR command modes	Cisco IOS XR Command Mode Reference

Standards

Standards	Title
No new or modified standards are supported by this feature, and support from existing standards has not been modified by this feature.	—

MIBs

MIBs	MIBs Link
—	To locate and download MIBs using Cisco IOS XR software, use the Cisco MIB Locator found at the following URL and choose a platform under the Cisco Access Products menu: http://cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

RFCs

RFCs	Title
RFC 3261	SIP: Session Initiation Protocol
RFC 2543	Session Initiation Protocol
RFC 2617	HTTP Authentication: Basic and Digest Access Authentication
RFC 4590	RADIUS Extension for Digest Authentication

Technical Assistance

Description	Link
The Cisco Technical Support website contains thousands of pages of searchable technical content, including links to products, technologies, solutions, technical tips, and tools. Registered Cisco.com users can log in from this page to access even more content.	http://www.cisco.com/techsupport