-
Cisco IOS XR System Error Reference Guide for XR12000 Series Platform Specific Messages, Release 3.4
-
Preface
-
Overview
-
Access Control List (ACL) Messages
-
Diagnostic Messages
-
Forwarding Messages
-
High Availability (HA) Messages
-
Installation Messages
-
Internet Protocol (IP) Messages
-
Layer 1 Messages
-
Layer 2 Messages
-
Manageability (MGBL) Messages
-
Operating System (OS) Messages
-
Packet Infrastructure Messages
-
Platform Messages
-
Quality of Service (QoS) Messages
-
Routing Messages
-
Index
-
Feedback
Table Of Contents
POLICY_REPOSITORY_DYNREG Messages
POLICY_REPOSITORY_EDM Messages
Routing Messages
This section contains all routing related System Error Messages, such as MPLS, OSPF, BGP, Multicast, MRIB, RIB, and so forth. The following facility codes are represented in this module:
•
POLICY_REPOSITORY_DYNREG Messages
•
ORA_SHARED Messages
Error Message%ROUTING-ORA_SHARED-4-ERR_DLL_REG Unable to register cerrno dll [chars] because [chars]
Explanation The given cerrno dll could not be marked for use. This does not change the functionality of the system but does obscure the meaning of error codes presented by this part of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
ORA Messages
Error Message%ROUTING-ORA-2-ERR_MEM_ALLOC Cannot allocate entry
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-ORA-3-DUPLICATE_DOCKENTRY Dock entry add failure
Explanation I really do not know.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-INIT Failure in init function in DLL [chars]
Explanation The library is incorrectly installed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSING_BASE_TYPE The base type '[chars]' v'[chars]' was used as a [chars] in a [chars]: '[chars]' type in area [chars]
Explanation One of the operations in one of the ORAs used a base type that was not defined in any of the ORA math sets.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSING_FUNCTION Route access library [chars] has no [chars] function
Explanation The library is incorrectly installed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-MISSING_OPERATOR The operator '[chars]' was not located in any of the '[chars]'s ORAs.
Explanation There is a function declared within the various docked ORAs at this attach point that uses an operator that does not exist with the same set of docked ORAs. Please contact support.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-3-THREADING Threading operation '[chars]' for '[chars]' failed because: [chars]
Explanation The presented threading operation failed. It is likely that policy multi-version calls will stop working and thus policy may not be operational.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-4-ERR_DLL_REG Unable to register cerrno dll [chars] because [chars]
Explanation The given cerrno dll could not be marked for use. This does not change the functionality of the system but does obscure the meaning of error codes presented by this part of the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-4-MERGE_FAILED Some base type(s) was(were) unavailable during AP merging at: [chars]
Explanation One or more base types where not available when bringing together the parts of this attach point. This is an item that should be caught during testing. If it does show up, support should be contacted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-4-MISSING_DOCK_INFO The dock data for docking item [chars] was missing
Explanation This is most likely an internal logic error that resulted in a given ora dockling being released more than once.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-7-DBGINIT Unable to bring up debug event structures: [chars]
Explanation The debug event initialization failed. The ora docker will still run correctly, but debug commands may be unavailable.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-ORA-7-DBGSHUTDOWN Unable to shutdown debug event structures: [chars]
Explanation The debug event shutdown failed. The ora docker will still run correctly, but debug commands may be unavailable.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPF_EDM Messages
Error Message%ROUTING-OSPF_EDM-3-DATALIST_ADD_FAILED Failed to add an external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-DATALIST_CREATE_FAILED Failed to create external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-DATALIST_SET_MORE_FLAG Failed to set external data manager more flag for datalist [chars]
Explanation A client has requested information through SysDB from OSPF. During execution of the request an attempt to set a flag indicating there is more data for the client failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-ENCODE_FAILED Failed to encode [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-LIST_ADD_FAILED Failed to add to an external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-LIST_CREATE_FAILED Failed to create external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_EDM-3-SYSDB_BIND_FAILED Failed to connect to SysDB ([chars])
Explanation The process failed to connect to SysDB while starting.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPF_POLICY Messages
Error Message%ROUTING-OSPF_POLICY-3-ORA_INSTBUILD Failed to build [chars], reason [chars] cer [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_POLICY-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPF_RIB Messages
Error Message%ROUTING-OSPF_RIB-3-ERR_PATH_ADD Error adding path to batching buffer
Explanation An error was encountered in the call to ipv4_rib_batch_add_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_PATH_DELETE Error deleting path from batching buffer
Explanation An error was encountered in the call to ipv4_rib_batch_delete_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_PROTO_MODIFY Error changing purgetime
Explanation An error was encountered in the call to ipv4_rib_protocol_modify.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_ROUTE_HDR Error adding route header to batching buffer for [chars]/[dec]
Explanation An error was encountered in the call to ipv4_rib_batch_add_route.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-3-ERR_UPDATE_DONE Error informing rib that batch is complete
Explanation An error was encountered in the call to ipv4_rib_batch_complete.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-4-BATCH_LOG_PATH RIB batch error, [chars] (result [dec]), prefix [hex]/[dec] next_hop [hex] intf [chars].
RetryingExplanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-5-BATCH_ERROR RIB batch error, [chars]
Explanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-5-BATCH_ERROR_CODE RIB batch error, [chars] ([hex])
Explanation The specified error was encountered in the OSPF RIB batching code.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_RIB-6-INFO_RT_HDR_NOTUSED Believes [chars]/[dec] and [chars]/[dec] differ
Explanation The RIB batching API believes that it already has this router header in the batching buffer.
Recommended Action No action is required.
OSPF_UV Messages
Error Message%ROUTING-OSPF_UV-3-CERR_REG_FAIL Failed to register internal error codes: [chars]
Explanation An error occurred during the registration of OSPF error codes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_DBG_REGISTER_FAILED Error initializing ospf_uv debugging: [chars]
Explanation An error occurred during initialization of the ospf_uv process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_MEM_ALLOC_FAIL Unable to allocate [unsigned int] bytes for '[chars]'
Explanation The ospf_uv process was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_PROC_READY Error signaling process ready: [chars]
Explanation The ospf_uv process was unable to signal process ready to sysmgr.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_CONNECT Error binding to SysDB: [chars]
Explanation The ospf_uv process was unable to bind to SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_DISCONNECT Error unbinding from SysDB: [chars]
Explanation The ospf_uv process was unable to unbind from SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_SYSDB_REG_VERIFY Error registering with SysDB: [chars]
Explanation The ospf_uv process was unable to register with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-ERR_VRFN_FNS_INIT Error setting SysDB callback functions: [chars]
Explanation The ospf_uv process was unable to initialize SysDB callbacks.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-EVENT_ERR Error in event loop: [chars]
Explanation An error occurred in the main ospf_uv event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-EVM_CRE_FAIL Error creating event connection manager: [chars]
Explanation The ospf_uv process was unable to create an event connection manager instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-3-INTF_FWS_INIT Error initializing forward-reference store: [chars]
Explanation The ospf_uv process was unable to initialize the forward-reference store library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF_UV-6-PROCESS_NAME Caution: The OSPF process name [chars] conflicts with a show or clear command name
Explanation The name chosen for the OSPF process matches an ospf show or clear command, or a command abbreviation. This can cause ambiguities with subsequent show or clear commands for this process.
Recommended Action Choose a different name for the OSPF process.
OSPF Messages
Error Message%ROUTING-OSPF-2-ERR_MEM_ALLOC No memory, [chars], process terminated
Explanation Memory allocation of a critical OSPF resource failed because of a low memory condition. The OSPF process was terminated.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-OSPF-3-ALLOC_ERR Allocation error, [unsigned int] bytes for [chars]
Explanation Allocation of the specified resource failed because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands.
Error Message%ROUTING-OSPF-3-AREANULL [chars]: area pointer is NULL
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-BADMSG ospf router received bad message type [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-BADSHARE Bad refcount at [hex] (refcount=[hex]) in [chars]
Explanation An internal software error occurred. Resources may be in inconsistent state.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-OSPF-3-BADTIMER Managed Timer error, [chars]: Unrecognized timer type [dec]
Explanation A timer was found with an unrecognized type
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-DBGINIT Debug init error, [chars]: event [chars], error [dec]
Explanation Unable to initialize a debugging flag
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-DUP_RTRID OSPF detected duplicate router-id [chars] from [chars] on interface [chars]
Explanation OSPF received hello packet from a neighbor which has the same router-id as this routing process. A full adjacency cannot be established.
Recommended Action OSPF router-id should be unique. Change the neighbors router-id.
Error Message%ROUTING-OSPF-3-ERR_RESOURCE_ALLOC No memory could be allocated for the resource, [chars]
Explanation Allocation of the specified resource failed because of a low memory condition. This could affect the protocol functionality.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands and preferably restart the OSPF process.
Error Message%ROUTING-OSPF-3-EVM External Event Manager error, [chars], error [chars] [[hex]]
Explanation A call to an external event manager function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EVM_CODE External Event Manager error, [chars]: [chars] code [dec], error [chars] [[hex]]
Explanation A call to an external event manager function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EXTERNALERR External error, [chars]
Explanation An external software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-EXTERNALERR_RC External error, [chars], error [hex]
Explanation An external software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-FRIS FRIS error, [chars], [chars] error [chars] [[hex]]
Explanation The FRIS request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IDBERR IDB error, [chars]: [chars], intf [chars] cerr [chars]
Explanation Error encountered while attempting to activate an idb. Problem could be corrupt data from IM or IP/ARM or the FRIS.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFCHECK Interface [chars] is attached to more than one area
Explanation An internal consistency check has failed. An interface appears to be associated with more than one area.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFINIT Interface init error, interface [chars]
Explanation OSPF failed to initialize data structures for an interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IFMGR External IFMGR error, [chars], intf [chars] error [chars] [[hex]]
Explanation The specified interface manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IGPTE IGP/TE error, [chars]: [chars] error [dec]
Explanation Error encountered while attempting to use the IGP_TE Lib.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INIT_ERR Init error, [chars], error [hex]
Explanation An error occurred during initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INTERNALERR Internal error, [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-INTERNALERR_RC Internal error, [chars], error [hex]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-IPARM External IP-ARM error, [chars], error [chars] [[hex]]
Explanation A call to an external IP-ARM function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-LWM External light-weight msg error, [chars], error [chars] [[hex]]
Explanation A call to an external light-weight messaging function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-MCAST Multicast error, [chars] [chars] on [chars], error [chars]
Explanation The above specified multicast operation failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-MEDIAERR Media error, [chars]: Interface [chars] unknown type: [chars]
Explanation Media table lookup failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-MUTEX Mutex error, [chars], [chars] mutex, error [chars] [[hex]]
Explanation An error occurred in the pthread functions used for thread synchronization. This is most likely a system error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-NOBACKBONE Flagged as being an ABR without a backbone area
Explanation The router was flagged as an Area Border Router (ABR) without backbone area in the router.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-NOIPADDR No IP Addr on interface [chars]. OSPF will not be run over it.
Explanation This message is displayed if ospf is configured on an unnumbered interface that is not of type point to point. In this case, ospf will not run on this interface.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-3-NOSELF if [chars] if_state [dec]
Explanation An internal error occurred. An interface was not fully initialized when an OSPF related event occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-NOTNBRTYPE Cannot configure neighbor on [chars]. Interface must be NBMA or P2MP
Explanation Neighbor cannot be configured on interface if it is not type NBMA or point to multipoint.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-3-PKTDROP Raw socket error, [chars]: packet dropped, [chars]
Explanation An input packet was dropped for the specified reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RDB_NO_LSA lsid [chars] adv [chars] type [dec] gateway [chars] metric [dec] network [chars] mask [chars] attr [hex] net-metric [dec]
Explanation OSPF found inconsistency between its database and topology table.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RECONF_VL OSPF process [chars] is changing router-id. Reconfigure virtual link neighbors with our new router-id
Explanation OSPF process is being reset, and it is going to select a new router-id. This will bring down all virtual links. To make them work again, virtual link configuration needs to be changed on all virtual link neighbors.
Recommended Action Change virtual link configuration on all the virtual link neighbors, to reflect our new router-id.
Error Message%ROUTING-OSPF-3-RIB External RIB error, [chars], error [chars] [hex]
Explanation A call to an external RIB function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RIB_MSG External RIB error, [chars]
Explanation A call to an external RIB function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-RPC External RPC error, [chars], error [chars] [[hex]]
Explanation An RPC error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-SOCKET External socket error, [chars], error [chars] [[hex]]
Explanation The above specified socket operation failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-SYSDB External SysDB error, [chars], error [chars] [[hex]]
Explanation An external OSPF error occurred when accessing the system database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-THREAD_CREATE Thread create error, [chars], error [chars] [[hex]]
Explanation OSPF failed to create a thread essential to its operation. This is an internal error. An automatic restart of the OSPF process was necessary to attempt recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-3-UNKNOWNSTATE Reached unknown state in neighbor state machine
Explanation An internal software error occurred. When processing and DBD packet, the neighbor was found to be in an indeterminate state.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-BADLENGTH Invalid length [dec] in OSPF packet from [chars] (ID [chars]), [chars]
Explanation The system received an OSPF packet with a length field of less than normal header size or inconsistent with the size of the IP packet in which it arrived. This indicates an error in the sender of the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-BADLSATYPE Invalid lsa: [chars] Type [dec], LSID [chars] from [chars], [chars], [chars]
Explanation The router received an LSA with invalid LSA Type. The cause is either memory corruption or unexpected behavior on a router.
Recommended Action Check both the sending and receiving routers for memory corruption. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-CONFLICTING_LSAID Found LSA with the same host bits but different mask.
LSA with shorter mask will be used.
LSA 1: [chars]/[dec]
LSA 2: [chars]/[dec]Explanation An LSA could not be generated because there is a supernet lsa with the host bit set LSA ID that conflicts with the major net LSA ID that also needs to have host bit set.
Recommended Action This is a limitation in OSPF's ability to handle conflicting LSA IDs. Attempt to avoid this limitation by modifying the generation of summary LSA's so that the LSA ID's do not conflict. Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-DEPRECATED_RTRID
outer-id [chars] command has been deprecated. Please delete
outer-id [chars] and reconfigure router-id.Explanation OSPF router-id has been deprecated.
Recommended Action Use router-id .
Error Message%ROUTING-OSPF-4-DOMAIN_TAG_NEEDED Domain-tag must be configured with 4-byte AS number in vrf [chars]
Explanation At the time of the redistribution of BGP with 4 byte AS number, domain-tag wasn't confiured. User needs to be aware that in this case domain-tag must be configured.
Recommended Action If not already configured domain-tag should be configured for the vrf.
Error Message%ROUTING-OSPF-4-ERR_MSG_GET_SCOID Error retrieving client's connection ID to the [chars] channel: [chars] ([dec])
Explanation OSPF failed to retrieve its local connection ID for a client attached to the specified channel. This is an internal programming error.
Recommended Action Restart the OSPF process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-ERR_MSG_REPLY Error replying to the client [chars]: [chars] ([dec])
Explanation OSPF failed to reply to its client through message channel. This could be a result of channel down or resource allocation failure.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.. Restart the OSPF process. *RECUR*
Error Message%ROUTING-OSPF-4-ERRRCV Received invalid packet: [chars] from [chars], [chars]
Explanation An invalid OSPF packet was received. Details are included in the error message. The cause might be a misconfigured OSPF or an internal error in the sender.
Recommended Action Check the OSPF configuration of the receiver and the sender for inconsistency. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-IFINDEX_GET Unable to get interface index for [chars]: [chars]
Explanation An error occurred when trying to get a numeric interface index value for the specified interface. Ietf nsf restart might fail.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-KEYCFG Key [unsigned long int] [chars]
Explanation An error occurred when trying to configure an ospf authentication key.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-4-MAX_INTF_APPLY Interface limit [dec] exceeded. Dropping interface [chars]
Explanation The number of interfaces configured exceeds the interface limit.
Recommended Action Either raise the maximum interface limit or unconfigure interfaces until the number is below the limit.
Error Message%ROUTING-OSPF-4-MUTEX_ERR [chars] [chars] mutex ([hex]), tid [dec] owner [hex] count [dec], error [chars] [[hex]]
Explanation An error has been returned by the functions used for locking/unlocking an OSPF synchronization mutex.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-NBREXIST Neighbors were configured when NBMA or P2MP. Changing network type will abandon that configuration. Please remove configured neighbors.
Explanation Neighbors had been configured earlier when the network type was nonbroadcast. The current configuration request will cause these configured neighbors to be abandoned.
Recommended Action Remove the configured neighbors.
Error Message%ROUTING-OSPF-4-NONEIGHBOR Received [chars] from unknown neighbor [chars]
Explanation OSPF hello, database description, or database request packet was received, but the router could not identify the sender. This is a normal occurrance if a link flap occurs on the router receiving the packet.
Recommended Action This situation should correct itself. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-NORTRID OSPF process [chars] cannot start without a router id. Configure router-id with the
outer-id command.Explanation OSPF failed while attempting to allocate a router ID from the IP address of one of its interfaces as no suitable IP address was available.
Recommended Action Make sure that there is at least one interface that is up and has a valid IP address. If there are multiple OSPF processes running on the router, each requires a unique router ID. You must have enough 'up' interfaces so that each of them can obtain a router ID. It is highly recommended that you configure loopback interfaces or use the router-id configuration command to better control the selection of OSPF router IDs.
Error Message%ROUTING-OSPF-4-NOTREDIST5 db_free: external LSA [chars]/[dec]
Explanation An internal software error occurred. OSPF is deleting an external LSA that should not be deleted.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-OLD_CMD Command [chars] has been upgraded by [chars]. Use the new command.
Explanation The command has been replaced by a newer command.
Recommended Action Use the new command inidicated in the message.
Error Message%ROUTING-OSPF-4-PAKMAN_EVENT Pakman event [chars] received, code=[dec], [chars]
Explanation An error has occured and pak manager sent use an event. If we can't recover from the error (ABORT event), OSPF will exit.
Recommended Action This is an indication that error(s) has occured in pakman No specific actions are required for OSPF.
Error Message%ROUTING-OSPF-4-POLICYCONFIG An error was encountered configuring policy, [chars]: [chars]
Explanation A problem was encountered while setting up route policy configuration. Some of the routing policy may not have been configured correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-RAW_OUTPUT_ERR Raw socket output err: [chars], src=[chars], dest=[chars], if=[chars], msglen=[dec]
Explanation An error has occured when OSPF is in process of sending a packet to the the raw socket.
Recommended Action This is an indication that error(s) has occured in other components and it is impacting OSPF's ability send data. No specific actions are required for OSPF.
Error Message%ROUTING-OSPF-4-REDIST_FAILED OSPF was unable to configure redistribution for protocol [chars]
Explanation An error occurred while OSPF was setting up redistribution for the named protocol. The redistribution will not take place.
Recommended Action This may be due to lack of memory, or due to a RIB failure, or to an internal OSPF problem. It may help to restart the OSPF process.
Error Message%ROUTING-OSPF-4-REDIST_MAX_PFX Redistribution prefix limit has been reached - [dec] prefixes
Explanation We have reached the maximum number of redistributed prefixes
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured.
Error Message%ROUTING-OSPF-4-REDIST_THR_PFX Redistribution prefix threshold has been reached - [dec] prefixes
Explanation We have reached the threshold level of number of redistributed prefixes.
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured.
Error Message%ROUTING-OSPF-4-STUB_ASBR Router is currently an ASBR while having only one area which is a stub area
Explanation Router is configured as an ASBR but is only connected to a single stub area. This can waste resources since the router has nowhere to send the external LSAs that it is generating.
Recommended Action Check configuration and disable redistribution of routes into ospf if appropriate.
Error Message%ROUTING-OSPF-4-USING_OLD_RTRID OSPF process [chars] encountered an error while finding a new router ID. The old router ID [chars] is being used as an interim value. clear ip ospf process will force another attempt to find a valid router ID.
Explanation OSPF failed while attempting to allocate a router ID from the IP address of one of its interfaces due to an unexpected internal problem.
Recommended Action Use 'clear ip ospf process' to force another attempt to find a valid router ID. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-4-VIRTUAL_IN_NON_BACKBONE Virtual link information found in non-backbone area: [chars]
Explanation An internal error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-5-ADJCHG Process [chars], Nbr [chars] on [chars] in area [chars] from [chars] to [chars], [chars]
Explanation An OSPF neighbor has changed state. The message describes the change and the reason for it. This message appears only if the log-adjacency-changes command is configured for the OSPF process.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-6-BADCHKSUM Checksum Failure in database in area [chars] Link State Id [chars] Old Checksum [hex] New Checksum [hex]
Explanation OSPF has detected a checksum error in the database due to memory corruption.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-DBEXIST area [chars] lsid [chars] mask [chars] adv [chars] type [dec]
Explanation OSPF has a problem locating the LSA, which could lead to a memory leak.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-GRACEFUL_SHUTDOWN [chars]
Explanation Informs user of graceful shutdown events. User needs to be aware of these activities.
Recommended Action No action required.
Error Message%ROUTING-OSPF-6-MAXMETRIC_RUNNING Current max-metric on-startup timer is running. New timer will be used at next reload.
Explanation maximum-metric LSA origination setting was changed while the maximum-metric origination was still active. The change will not take effect until the next time the system is restarted.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-6-MEM_NOTIF [chars] [chars].
Explanation An unexpected event from the system monitor was seen.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-MGDTIMER External Managed Timer error, [chars], error [chars] [[hex]]
Explanation An external managed timer support routine failed. The affect this error has on the proper operation of OSPF depends on where and when this error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-6-NEWLIMIT [chars] limit changed. Old: [dec] New: [dec]
Explanation User has changed the configuable resource limit.
Recommended Action No action required. This is an informational message.
Error Message%ROUTING-OSPF-6-NOTREDIST3 build_ex_route(): don't redistribute net [chars]/[dec], [chars] advertises it already
Explanation For information only. Another router with a greater router ID is advertising the same external LSA. This router will stop originating the LSA to eliminate the redundancy.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-6-REFBW_CHG Reference bandwidth is changed. Please ensure reference bandwidth is consistent across all routers.
Explanation Informational message reminding the user that reference bandwidth should be consistent across all routers in the area.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-6-USING_MSGDGST Message-digest is used when both it and cleartext password are configured
Explanation Inform user that when both a clear text password and message-digest key are configured the message-digest key will be used.
Recommended Action No action is required.
Error Message%ROUTING-OSPF-7-DB_EX_DQUEUE [chars]: Unexpected external ReadyQ count of 0, &db=[hex], &rtr=[hex]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-DB_READY_Q InReadyQ flag set for external DB, db [chars] on rtr_rt [chars]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-DLINK dld [chars] is NULL
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-DQUEUE Double link queue count is 0 before decrement, &queue=[hex]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-ERR_TUNNEL_INT TE IDB error, [chars], [chars] error [chars] [[hex]]
Explanation Error in creating a tunnel interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPF-7-INIT_FAIL Initialization failure, [chars], process terminated
Explanation An error occurred during initialization, causing the process to terminate.
Recommended Action Copy the error message exactly as it appears, and report it to your technical support representative.
Error Message%ROUTING-OSPF-7-VRF_DELETE VRF delete error [chars] [chars] [chars]
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFv3_EDM Messages
Error Message%ROUTING-OSPFv3_EDM-3-DATALIST_ADD_FAILED Failed to add an external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-DATALIST_CREATE_FAILED Failed to create external data manager datalist for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager datalist has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-EDMINIT Error initializing EDM thread: [chars]: [chars]
Explanation An error occurred during initialization of the EDM thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-ENCODE_FAILED Failed to encode [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-EVENT_REGISTRATION_FAILED Failed to connect to the event manager: [chars]
Explanation The process failed while attempting to connect to an event manager channel for the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-LIST_ADD_FAILED Failed to add to an external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-LIST_CREATE_FAILED Failed to create external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-NO_DATA Data for [chars] is not available
Explanation The data needed for the specified OSPF show command was not available. This would occur for non-critical data such as trace or debug information.
Recommended Action No action is required.
Error Message%ROUTING-OSPFv3_EDM-3-PROTO_REG_FAILED Failed to register show protocol information : [hex], '[chars]'
Explanation OSPFv3 was unable to register for support of the show protocol command.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-REGISTER_FAILED Failed to register its [chars] external data manager, '[chars]'
Explanation The process failed when attempting to register its external data manager with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-SYSDB_BIND_FAILED Failed to connect to SysDB ([chars])
Explanation The process failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-3-SYSDB_COID_FAILED Failed to convert during a conn to coid conversion
Explanation The process failed to convert a conn to a coid while starting the indicated subsystem. This generally can only occur when starting up.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_EDM-6-BAGREG_FAILED Failed to register its external data manager data blocks
Explanation The process failed while attempting to register its external data manager data blocks with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFV3_POLICY Messages
Error Message%ROUTING-OSPFV3_POLICY-3-ORA_INSTBUILD Failed to build [chars], reason [chars] cer [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFV3_POLICY-3-ORA_RUN Could not apply policy operation [chars] to attribute [chars] because [chars]
Explanation Internal error in policy library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFv3_RIB Messages
Error Message%ROUTING-OSPFv3_RIB-2-NO_MEMORY Unable to allocate space for rib batching buffer: No Memory
Explanation Insufficent memory to allocate buffer for RIB batching API'
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-OSPFv3_RIB-3-BIND Unable to bind to the RIB
Explanation An error occurred on a request to bind to the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-DEFAULT_REG Unable to register with the RIB to receive the default route: [chars]
Explanation An error occurred on a request to have the RIB send us route updates for the default route.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-DISCONNECT Error while disconnecting RIB Event connection
Explanation An error occurred during an attempt to tear down the RIB Event connnection.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_BATCH_COMPLETE Error informing rib that batch is complete
Explanation An error was encountered in the call to ipv6_rib_batch_buffer_complete.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_PATH_ADD Error adding path-add to batching buffer (#[hex])
Explanation An error was encountered in the call to ipv6_rib_batch_add_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_PATH_DELETE Error adding path-delete to batching buffer ([hex])
Explanation An error was encountered in the call to ipv6_rib_batch_delete_path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_ROUTE_HDR Error adding route header to batching buffer for [chars]/[dec] ([hex])
Explanation An error was encountered in the call to ipv6_rib_batch_add_route.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-ERR_UPDATE_COMPLETE Error informing rib that update is complete: [chars]
Explanation An error was encountered in the call to ipv6_rib_update_complete.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-FINDPDB Unable to get a RIB handle for [chars] routes: [chars]
Explanation An error occurred on a request to find the handle for the specified type of routes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-PURGE Error removing OSPFv3 routes from the IPv6 RIB: [chars]
Explanation An error was encountered in the call to ipv6_rib_purge_protocol.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-REDIST_REG Unable to register with the RIB to receive updates for [chars] routes: [chars]
Explanation An error occurred on a request to have the RIB send us route updates for the specified type of routes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_RIB-3-REGISTER Unable to register OSPFv3 with the RIB: [chars]
Explanation An error occurred on a request to register the OSPFv3 protocol with the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
OSPFv3_UV Messages
Error Message%ROUTING-OSPFv3_UV-3-CERR_REG_FAIL Failed to register internal error codes: [chars]
Explanation An error occurred during the registration of OSPFv3 error codes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_DBG_REGISTER_FAILED Error initializing ospfv3_uv debugging: [chars]
Explanation An error occurred during initialization of the ospfv3_uv process.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_MEM_ALLOC_FAIL Unable to allocate [unsigned int] bytes for '[chars]'
Explanation The ospfv3_uv process was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_PROC_READY Error signaling process ready: [chars]
Explanation The ospfv3_uv process was unable to signal process ready to sysmgr.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_SYSDB_CONNECT Error binding to SysDB: [chars]
Explanation The ospfv3_uv process was unable to bind to SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_SYSDB_DISCONNECT Error unbinding from SysDB: [chars]
Explanation The ospfv3_uv process was unable to unbind from SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_SYSDB_REG_VERIFY Error registering with SysDB: [chars]
Explanation The ospfv3_uv process was unable to register with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-ERR_VRFN_FNS_INIT Error setting SysDB callback functions: [chars]
Explanation The ospfv3_uv process was unable to initialize SysDB callbacks.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-EVENT_ERR Error in event loop: [chars]
Explanation An error occurred in the main ospfv3_uv event loop.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-EVM_CRE_FAIL Error creating event connection manager: [chars]
Explanation The ospfv3_uv process was unable to create an event connection manager instance.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-3-INTF_FWS_INIT Error initializing forward-reference store: [chars]
Explanation The ospfv3_uv process was unable to initialize the forward-reference store library.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3_UV-6-PROCESS_NAME Caution: The OSPFv3 process name [chars] conflicts with a show or clear command name
Explanation The name chosen for the OSPFv3 process matches an ospf show or clear command, or a command abbreviation. This can cause ambiguities with subsequent show or clear commands for this process.
Recommended Action Choose a different name for the OSPFv3 process.
OSPFv3 Messages
Error Message%ROUTING-OSPFv3-2-NOMEMORY No memory for [chars]
Explanation The requested operation could not be accomplished because of a low memory condition.
Recommended Action This indicates a low memory condition. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-OSPFv3-3-ACL_GET Unable to get prefix-list [chars]: [chars]
Explanation An error occurred when trying to get the named prefix-list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-ACL_REG Unable to register prefix-list [chars]: [chars]
Explanation An error occurred when trying to register for changes to the named prefix-list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-ALLOCFAIL [chars] allocation failed: [chars]
Explanation Allocation of the specified resource failed, probably due to low memory.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-APIERR Call to [chars] from [chars] returns: [chars]
Explanation A lower-level support function returned an unexpected status.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-BADMSG Router thread received an invalid message type: [dec]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-BADTIMER Unrecognized [chars] timer type [dec]
Explanation A timer was found with an unrecognized type
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-CERR_REGISTER Failed to register internal error codes: [chars]
Explanation An error occurred during the registration of OSPFv3 error codes.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-CONN_FAIL Unable to connect to server [chars] : [chars]
Explanation OSPFv3 was unable to open a connection to a server. This is an internal error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DBGINIT Debug event initialization failed: [chars]
Explanation Unable to initialize a debugging flag.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DBGREG Debug registration failed: [chars]
Explanation Unable to initialize debugging flags. Debug commands will not function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DELVLINK Cannot delete virtual link, backbone is being deleted
Explanation The virtual link cannot be removed because OSPFv3 is in the process of deleting the backbone area. Try again later.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DLINK dld [chars] is NULL
Explanation An internal software error occurred
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-DUP_RTRID Detected duplicate router ID [chars] from [chars] on interface [chars]
Explanation OSPFv3 received hello packet from a neighbor which has the same router ID as this routing process. A full adjacency cannot be established.
Recommended Action OSPFv3 router ID must be unique. Change the router ID.
Error Message%ROUTING-OSPFv3-3-DUP_RTRID_AREA Detected router with duplicate router ID [chars] in area [chars]
Explanation OSPFv3 has received multiple router LSAs with our router ID.
Recommended Action OSPFv3 router ID must be unique. Change the router ID.
Error Message%ROUTING-OSPFv3-3-DUP_RTRID_AS Detected router with duplicate router ID [chars] in inter-area router LSA advertised by [chars]
Explanation OSPFv3 has received an inter-area router LSA with our router ID.
Recommended Action OSPFv3 router ID must be unique. Change the router ID.
Error Message%ROUTING-OSPFv3-3-EVENTBLOCK Event blocking error in [chars] thread: [chars]
Explanation An error occurred while a thread was blocked waiting for an event
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-EVM_FD Error obtaining the [chars] file descriptor: [chars]
Explanation A call to get the file descriptor associated with an event manager connection failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-EVM_RETRY Unable to set event manager retry values for the [chars] connection: [chars]
Explanation A call to the external event manager to set connection retry values failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-FRIS_INSERT Unable to insert interface [chars] in the forward reference list: [chars]
Explanation An error occurred when adding the interface to the forward-reference list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-HELLOINIT Error initializing hello thread: [chars]: [chars]
Explanation An error occurred during initialization of the hello thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFINDEX_GET Unable to get interface index for [chars]: [chars]
Explanation An error occurred when trying to get a numeric interface index value for the specified interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFINIT Initialization failure for interface [chars]
Explanation OSPFv3 failed to initialize data structures for an interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFMGR [chars] failed: [chars]
Explanation The specified interface manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IFMGR_IF [chars] failed for interface [chars]: [chars]
Explanation The specified interface manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INIT Initialization failed [[chars]], process terminated
Explanation An error occurred during initialization, causing the OSPFv3 process to terminate.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INSTALL_REG Unable to register for package installation notifications: [chars]
Explanation An error occurred when trying to register with the packaging subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INSTALL_UNREG Unable to unregister for package installation notifications: [chars]
Explanation An error occurred when trying to unregister with the packaging subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-INTERNALERR Internal error: [chars]
Explanation An internal software error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPARM [chars] failed: [chars]
Explanation The specified IP/ARM request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPARM_IF [chars] failed for interface [chars]: [chars]
Explanation The specified IP/ARM request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_CLOSE Error terminating IPSec processing for interface [chars]: [chars]
Explanation An error occurred when trying to close an IPSec SA for the named interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_DEBUG_INIT Unable to initialize ipsec debugging: [chars]
Explanation An error occurred when trying to initialize the ipsec debug commands.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_INIT Error initializing IPSec support: [chars]%s
Explanation An error occurred when trying to initialize the OSPFv3 IPSec subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-IPSEC_OPEN Error initiating IPSec processing for interface [chars]: [chars]
Explanation An error occurred when trying to open an IPSec SA for the named interface.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-LAS [chars] failed: [chars]
Explanation The specified Local Address Service request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-LAS_ADDR Interface [chars] does not have a link-local address assigned
Explanation The specified interface has not received a link-local address from the Local Address Service.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-LAS_IF [chars] failed for interface [chars]: [chars]
Explanation The specified Local Address Service request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-MCAST Multicast [chars] on [chars] failed: [chars]
Explanation The specified multicast operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-MEM_ALLOC_FAIL Unable to allocate [unsigned int] bytes for '[chars]'
Explanation OSPFv3 was unable to allocate memory for the specified resource.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-MUTEX_INIT Error [chars] for [chars] mutex: [dec]
Explanation A error occurred in the initialization of the primitives used for thread synchronization. This is most likely a system error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-NO_VL_ENDPOINT Unable to add host route for virtual link endpoint in area [chars]
Explanation No IPv6 address was available to use as an endpoint for a virtual link.
Recommended Action Configure a loopback interface with an IPv6 address and add it to the specified area.
Error Message%ROUTING-OSPFv3-3-NOBACKBONE Flagged as being an ABR without a backbone area
Explanation The router was flagged as an Area Border Router (ABR) without backbone area in the router.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-NOSELF Interface [chars] if_state [dec]
Explanation An internal error occurred. An interface was not fully initialized when an OSPFv3 related event occurred.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-NOTNBRTYPE Cannot configure neighbor on [chars]: interface must be NBMA or P2MP
Explanation Neighbor cannot be configured on interface if it is not type NBMA or point to multipoint.
Recommended Action No action is required.
Error Message%ROUTING-OSPFv3-3-PKTDROP Packet dropped: [chars]
Explanation An input packet was dropped for the specified reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-PKTDROP_STR Packet dropped: [chars]: [chars]
Explanation An input packet was dropped for the specified reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-PROCINIT Error initializing OSPFv3 process: [chars]: [chars]
Explanation An error occurred during OSPFv3 process initialization.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-RIB [chars] [chars]/[dec]: [chars]
Explanation An error occurred on a request to the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-RIB_ERR_PROTO_MODIFY Failed to modify purgetime with V6 RIB. Old [dec] New [dec]: [dec]
Explanation An error occurred on a request to the RIB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-RTRINIT Error initializing router thread: [chars]: [chars]
Explanation An error occurred during initialization of the router thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-SOCKET Socket operation [chars] failed: [chars]
Explanation The specified socket operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-SYSDB SysDB error: [chars]([chars]): [chars]
Explanation An error occurred when accessing the system database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-SYSMGR [chars] failed: [chars]
Explanation An specified system manager request failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-THREAD_CREATE Error starting [chars] thread: [dec]
Explanation OSPFv3 failed to create a thread essential to its operation. This is an internal error. An automatic restart of the OSPFv3 process was necessary to attempt recovery.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-UCAST Unicast [chars] on [chars] failed: [chars]
Explanation The specified unicast filter operation failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-UNKNOWNSTATE Reached unknown state in neighbor state machine
Explanation An internal software error occurred. When processing and DBD packet, the neighbor was found to be in an indeterminate state.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-3-UNSUPPORTED_IFTYPE Unsupported interface type [chars]: [chars]
Explanation The interface type is not yet supported by OSPFv3.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADAREA Received invalid packet: Incorrect area number ([chars]) from [chars], [chars]
Explanation The system received an OSPFv3 packet with an area ID that does not match the area that the interface belongs to.
Recommended Action Check the OSPFv3 configuration of the receiver and the sender for inconsistency. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADLENGTH Received invalid packet: Incorrect length ([dec]) from [chars], [chars]
Explanation The system received an OSPFv3 packet with a length field of less than normal header size or inconsistent with the size of the IPv6 packet in which it arrived. This indicates an error in the sender of the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADLSA Invalid LSA: [chars], Type [hex] LSID [unsigned int] from [chars], [chars], [chars]
Explanation The router received an invalid LSA. The cause is either memory corruption or unexpected behavior on a router.
Recommended Action Check both the sending and receiving routers for memory corruption. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-BADVERS Received invalid packet: Incorrect OSPF version ([dec]) from [chars], [chars]
Explanation The system received an OSPFv3 packet with an OSPF version field other than 3. This indicates an error in the sender of the packet.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-DEPRECATED_RTRID
outer-id [chars] command has been deprecated. Please delete
outer-id [chars] and reconfigure router-id.Explanation OSPFv3 router-id has been deprecated.
Recommended Action Use router-id .
Error Message%ROUTING-OSPFv3-4-ERRRCV Received invalid packet: [chars] from [chars], [chars]
Explanation An invalid OSPFv3 packet was received. Details are included in the error message. The cause might be a misconfigured OSPFv3 or an internal error in the sender.
Recommended Action Check the OSPFv3 configuration of the receiver and the sender for inconsistency. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-LSDB_ERROR Database error: [chars], Type [hex] LSID [unsigned int] from [chars]
Explanation OSPFv3 detected an error with its link state database.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-LTRACE_INIT Unable to initialize the ltrace buffer [chars]: [chars]
Explanation An error occurred when trying to create a buffer for tracing.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-NONEIGHBOR Received [chars] from unknown neighbor [chars] on [chars]
Explanation OSPFv3 hello, database description, or database request packet was received, but the router could not identify the sender. This is a normal occurrance if a link flap occurs on the router receiving the packet.
Recommended Action This situation should correct itself. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-NORTRID OSPFv3 process [chars] could not pick a router-id, please configure manually
Explanation OSPFv3 failed while attempting to allocate a router ID.
Recommended Action Use the 'router-id' command to specify a unique Router ID for this OSPFv3 process.
Error Message%ROUTING-OSPFv3-4-PKTDROP_WARN Packet dropped: [chars]
Explanation An input packet was dropped for the specified reason.
Recommended Action Such errors are possible during raw_ip restarts. If seen otherwise, these errors should be reported to SUPPORT.
Error Message%ROUTING-OSPFv3-4-POLICYCONFIG An error was encountered configuring policy, [chars]: [chars]
Explanation A problem was encountered while setting up route policy configuration. Some of the routing policy may not have been configured correctly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-REDIST_MAX_PFX Redistribution prefix limit has been reached - [dec] prefixes
Explanation We have reached the maximum number of redistributed prefixes
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured.
Error Message%ROUTING-OSPFv3-4-REDIST_THR_PFX Redistribution prefix warning threshold has been reached - [dec] prefixes
Explanation We have reached the warning threshold number of redistributed prefixes.
Recommended Action Check if redistribution of large number of prefixes is desired and has not been wrongly configured
Error Message%ROUTING-OSPFv3-4-SOCKET_WARN Socket operation [chars] failed: [chars]
Explanation The specified socket operation failed.
Recommended Action Such errors are possible during raw_ip restarts. If seen otherwise, these errors should be reported to SUPPORT.
Error Message%ROUTING-OSPFv3-4-STUB_ASBR Router is currently an ASBR while having only one area which is a stub area
Explanation Router is configured as an ASBR but is only connected to a single stub area. This can waste resources since the router has nowhere to send the external LSAs that it is generating.
Recommended Action Check configuration and disable redistribution of routes into OSPFv3 if appropriate.
Error Message%ROUTING-OSPFv3-4-USING_OLD_RTRID OSPFv3 process [chars] encountered an error while finding a new router ID. The old router ID [chars] is being used as an interim value.
Explanation OSPFv3 failed while attempting to allocate a router ID from the IPv4 address of one of its interfaces due to an unexpected internal problem.
Recommended Action Use 'clear ospfv3 process' to force another attempt to find a valid router ID. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-4-VIRTUAL_IN_NON_BACKBONE Virtual link information found in non-backbone area: [chars]
Explanation An internal error occurred.
Recommended Action Copy the error message exactly as it appears on the console or in the system log. Issue the show tech-support command to gather data that may provide information to determine the nature of the error. If you cannot determine the nature of the error from the error message text or from the show tech-support output, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-5-ADJCHG Process [chars], Nbr [chars] on [chars] from [chars] to [chars], [chars]
Explanation An OSPFv3 neighbor has changed state. The message describes the change and the reason for it. This message appears only if the log-adjacency-changes command is configured for the OSPFv3 process.
Recommended Action No action is required.
Error Message%ROUTING-OSPFv3-6-AREA_DELETE Area [chars] is being deleted, please try later
Explanation The configuration command could not be accepted because OSPFv3 is in the process of deleting the specified area. Try again later.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-6-AREACREATE Error creating area [chars]: [chars]
Explanation An error was encountered when trying to create an area.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-6-BADCHKSUM Checksum Failure in database: area [chars] LSA type [hex] LSID [hex] adv rtr [chars]: Old Checksum [hex] New Checksum [hex]
Explanation OSPFv3 has detected a checksum error in the database due to memory corruption.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-OSPFv3-6-REFBW_CHG Reference bandwidth is changed. Please ensure reference bandwidth is consistent across all routers.
Explanation Informational message reminding the user that reference bandwidth should be consistent across all routers in the area.
Recommended Action No action is required.
PIM_NETIO Messages
Error Message%ROUTING-PIM_NETIO-3-DEBUG_ERR [chars] failed : '[chars]'
Explanation PIM Netio dll failed initialization or registration with the debugging subsystem. This resulted in the restart of NetIO process.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
POLICY_REPOSITORY_DYNREG Messages
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-ADD Failed to add node location [chars] for protocol: [chars], version: [chars], ap_name: [chars] preventing successful registration for this item, because: [chars].
Explanation An error was encountered as the node location was being added to the attach point item. This will prevent the successful registration for this attach point and will leave this configuration space unverified with respect to policy configuration.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-CREATE Failed to create the attach point data for dynamic registration item: [chars], because: [chars]
Explanation An error was encountered as attach point data was being created. This could cause problems with future configuration attempts, and it does indicate an internal inconsistency so it might be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-DATA Failed to extract [chars] data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as data was being extracted for the registration of this attach point. As such, the registration failed and the verification of configuration related to this attach point registration will NOT be performed. Thus, configuration could be accepted but could be unable to be processed by the protocols.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-DELETE Failed to delete the attach point data for dynamic registration item: [chars], because: [chars]
Explanation An error was encountered as attach point data was being deleted. This could cause problems with future configuration attempts, and it does indicate an internal inconsistency so it might be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-DOCK Failed to dock the new data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as new attach point data was being docked. As a result, the new data has not been activated for this attach point. At this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-FIND Failed to find data for protocol: [chars], version: [chars], ap_name: [chars], during a [chars] operation, because: [chars]
Explanation An error was encountered as we were looking up data for the above attach point. The operation in question do not succeed since we could not find this entry, and thus the policy_repository could be in an inconsistent state.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-INSTALL Failed to install the new attach point data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as new attach point data was being swapped out for old data. As a result, the old data is either still activated, or NO data is activated for this attach point. As this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-MODIFY Failed to find data for a [chars] for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as we were looking up data for the above attach point. The operation in question did not succeed, and thus the policy_repository could be in an inconsistent state.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-REGISTER Failed to register (for verification) to the attach point data for dynamic registration item: [chars], because: [chars]
Explanation An error was encountered as attach point data was being registered for verification. At this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-SWITCH We have detected a condition where there are conflicting registration values for protocol: [chars], version: [chars], ap_name: [chars], and are swapping out the current values for new values. The data for this can be viewed by executing the appropriate bind point show command.
Explanation An error was encountered as the node location was being added to the attach point item. This will prevent the successful registration for this attach point and will leave this configuration space unverified with respect to policy configuration.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-UNDOCK Failed to undock the old [chars] data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as old attach point data was being undocked for new data. As a result, the old data is either still activated, or NO data is activated for this attach point. As this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-UNLOAD Failed to unload the old attach point data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as old attach point data was being unloaded for new data. As a result, the old data is either still activated, or NO data is activated for this attach point. As this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_DYNREG-3-UNREGISTER Failed to unregister (for verification) the old attach point data for protocol: [chars], version: [chars], ap_name: [chars], because: [chars]
Explanation An error was encountered as old attach point data was being unregistered for new data. As a result, the registration for the old data is still activated for this attach point. As this point is would be best to restart the policy_repository to try to clear this inconsistency.
Recommended Action Restart the policy_repository process to remedy this situation. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
POLICY_REPOSITORY_EDM Messages
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_BAG_ENCODE Failed to encode [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be encoded.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_BIND Failed to connect to SysDB ([chars])
Explanation The process failed to connect to SysDB while starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_EDM_DATA_GENERATE Failed to generate [chars] data in external data manager
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The data requested could not be generated.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_EDM_LIST_ADD Failed to add to an external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The attempt to add an item to an external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_EDM_LIST_CREATE Failed to create external data manager list for [chars]
Explanation A process has requested information through SysDB, probably as the result of executing a show command. The creation of the external data manager list has failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_EDM_REG Failed to register its external data manager
Explanation The process failed when attempting to register its external data manager with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-3-ERR_SYSDB_UNBIND Failed to unconnect to SysDB ([chars])
Explanation The process failed to disconnect from SysDB before starting the indicated subsystem.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY_EDM-6-ERR_SYSDB_BAG_REG Failed to register its external data manager data blocks
Explanation The process failed while attempting to register its external data manager data blocks with SysDB.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
POLICY_REPOSITORY Messages
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_MEM_ALLOC Failed to allocate resources for [chars]
Explanation The policy_repository process failed allocated memory for the operation specified.
Recommended Action The policy_repository process may function properly in the future but the operations associated with this configuration are likely in an inconsistent state. Restarting the policy_repository may correct the situation if the memory is being consumed by this process; otherwise restarting the procees that is consuming the memory may be advisable. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_ORA_DOCK Failed to dock with ORA [chars], version = [chars], location = [chars], signature = [chars], path = [chars] because: [chars]. This will result in NO policy being monitored or processed for this client.
Explanation The policy_repository process, while trying to dock with the client ORA encountered an error.
Recommended Action Restart the policy_repository and/or client. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_SYSDB_BAG_DECODE An attempt is being made to decode item ([chars]) which failed ([chars])
Explanation The system is attempting to process a policy object set or named policy and cannot decode the object.
Recommended Action Look for out of resource conditions. If memory is low, then restart the policy_repository process and reapply the configuration. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_SYSDB_CONNECT Failed to connect to the system database at '[chars]' ([chars])
Explanation The policy_repository process failed to bind to the system database at the displayed bind point.
Recommended Action The policy_repository process must be restarted before it can function correctly. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_SYSDB_GET Failed to retrieve configuration item: [chars] (Reason: [chars])
Explanation The policy_repository process failed to retrieve an item from the system database.
Recommended Action The policy_repository process may function properly in the future but the operations associated with this configuration are likely in an incinsistent state. Consider restarting the process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_SYSDB_REG_NOTIFY Failed to register for database notifications at: [chars] (Reason: [chars])
Explanation The policy_repository process failed to register for notification of changes on the displayed database path.
Recommended Action The policy_repository process must be restarted before it can function correctly. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-3-ERR_SYSDB_REG_VERIFY Failed to register for database verifications at: [chars] (Reason: [chars])
Explanation The policy_repository process failed to register for verification of changes on the displayed database path.
Recommended Action The policy_repository process must be restarted before it can function correctly. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-4-CLEANUP Failed to clean up policy '[chars]' ([chars])
Explanation When deleting the specified policy, the policy_repository process encountered a problem. This could leave memory unfreed.
Recommended Action If the policy_repository process is using an excessive amount of memory, consider restarting it with 'proc restart policy_repository' to clean up any unused memory. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-4-ERR_SYSDB_DELETE Failed to remove policy [chars] (Reason: [chars])
Explanation The policy_repository process encountered an error while trying to remove the data for a deleted policy.
Recommended Action This can only occur when there are no references to the deleted policy in the first place, and therefore will not have any harmful effects. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-4-PARSER_DLL Policy parser DLL: [chars]: [chars]@[chars].[dec]: [chars]
Explanation A system call failed inside the routing policy parser DLL.
Recommended Action Try again: the failure might have been due to resource issues. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-4-RPL_EDIT RPL editor: [chars]: [chars]@[chars].[dec]: [chars]
Explanation A system call failed inside the RPL editor program.
Recommended Action Try again: the failure might have been due to resource issues. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-4-SYSMGR_GET_NODE_STATE Failed to receive the [active/standby] state indication. Error: [chars]
Explanation An error occurred while trying to get the system [active/standby] state. A state of REDUNDANCY_UNKNOWN will be assumed. This process also registers for notification of changes to the [active/standby] state. Thus, the state can be determined by this means as well. Failure to receive notification for either one of these means could result in this process not functioning properly. Note: At least one of the processes in an active/standby pair must be active in order to assure proper functioning.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-ARG_MISMATCH Argument list mismatch for statement '[chars] [chars]' in policy [[chars]].
Explanation The user is trying to do an operation in which the number of arguments entered does not match the number of argument expected.
Recommended Action Correct the number of parameters that are passed in. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-ATTACHPOINT_ADD Failed to associate [chars] attach point item '[chars]' to policy [chars]. This will leave the policy repository in an inconsistent state.
Explanation The policy_repository process was not able to add the attach point to the policy in question. This means that the policy repository will not verify the statements in this policy against the attach point in question. This could allow statements to be added to the policy that (could) result in run time errors in the client at this attach point.
Recommended Action Restart the policy_repository process. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-ATTACHPOINT_MISMATCH Failed to process [chars] attach point item '[chars]' because [chars]. This will leave the policy repository in an inconsistent state.
Explanation The policy_repository process was not able to extract the policy name OR id value for this attach point path. This means that the policies that are actually using this attach point will NOT be recorded and thus policies *could* be deleted while still in use.
Recommended Action Restart the policy_repository. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-ITEM_UNSUPPORTED The item of type [chars] and value ([dec]) is not recognized by the policy_repository.
Explanation The policy_repository process was not able to extract the the item for this type. Please add support to the policy_repository or remove support from the protocols.
Recommended Action This indicates and internal inconsistency between the policy_repository and the protocols. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-OBJECT_INIT Failed to initialize [chars]. Error ([hex]): [chars]
Explanation The policy_repository was atempting to initialize a data object and it failed.
Recommended Action Look for out of resource conditions. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-OBJECT_REBUILD Failed to rebuild the [chars] data. Error ([hex]): [chars]
Explanation The system was atempting to rebuild an object and it failed.
Recommended Action Look for out of resource conditions. The policy_repository will exit and restart. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-POLICY_TOO_BIG Policy [[chars]] contains a large number of statements and would cause the policy repository to exceed resource limits. The policy repository is now inconsistent with the running configuration. To regain consistency, rollback to the previous configuration for this policy.
Explanation The policy named is very long and/or complex, and in compiling it for execution, the policy repository exhausted resource limits. This was not detected by the usual checks at configuration verification time. Rather than crash, the policy repository is left with the previous configuration for this policy, if any.
Recommended Action Rollback the configuration operation to regain consistency between the running configuration and the policy respoitory. Then, rewrite the policy in question in a simpler form. It may help to make use of policies with parameters to reduce the total policy size. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-SETS_REBUILD Internal inconsistency rebuilding sets for policy [chars] (Reason: [chars])
Explanation The policy_repository process failed to rebuild the set references for the policy in question. This will result in an inconsistent state in the policy_repository and the process should be restarted. This could result in policies not functioning properly.
Recommended Action The policy_repository process should be restarted to clean up the internal inconsistency. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%ROUTING-POLICY_REPOSITORY-7-VERIFY_APPLY Policy [[chars]] failed verification for use in policy [[chars]]
Explanation The policy_repository process, while verifying a change to a policy, encountered an error while checking the validity of the change in the policies that are applied by that policy.
Recommended Action Fix the offending argument in the applied policy so that it is accepted by the client (i.e. BGP, OSPF, etc.) Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.