-
Cisco IOS XR System Error Reference Guide for Platform Independent Messages, Release 3.4
-
Preface
-
Overview
-
Access Control List (ACL) Messages
-
Default Messages
-
Diagnostic Messages
-
Fabric Messages
-
Forwarding Messages
-
High Availability (HA) Messages
-
Installation Messages
-
Internet Protocol (IP) Messages
-
Layer 1 Messages
-
Layer 2 Messages
-
License Messages
-
Media Messages
-
Manageablity (MGBL) Messages
-
Operating System (OS) Messages
-
Packet Infrastructure Messages
-
Platform Messages
-
Quality of Service (QoS) Messages
-
Routing Messages
-
Security Messages
-
Service Messages
-
Simple Network Management Protocol (SNMP) Messages
-
System Database Messages
-
Index
-
Feedback
Table Of Contents
NVRAM_PLATFORM_COMMON Messages
Media Messages
This section contains all MEDIA related System Error Messages, including disk, nvram, flash, and so forth. The following facility codes are represented in this module:
•
NVRAM_PLATFORM_COMMON Messages
DISKUTIL Messages
Error Message%MEDIA-DISKUTIL-3-INIT_ERROR Unexpected init error: [chars]: [chars]: [hex]
Explanation An unexpected init error condition encountered.
Recommended Action Collect system log information. No action is required.
FLASHFS_HES Messages
Error Message%MEDIA-FLASHFS_HES-1-BADDEVOPEN Can't open device [chars]
Explanation Flash device could not be opened
Recommended Action Make sure the flash device resource manager is running. If not restart it. If that fails Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-1-BADOPTIONS [chars]: invalid option [char]
Explanation Bad options
Recommended Action Start the flash file system with correct options
Error Message%MEDIA-FLASHFS_HES-1-BADPATH [chars]: Can't Attach Pathname [chars]
Explanation Could not attach pathname
Recommended Action Reboot the router if possible. If not try to start it from the command line. If that too fails Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-1-BADPERM [chars]: Illegal permission requested ([dec])
Explanation Not a valid permission
Recommended Action No action is required.
Error Message%MEDIA-FLASHFS_HES-1-CARD_UNAVAILABLE [chars]: Can not access flash device
Explanation Probably the flash card has been removed.
Recommended Action Reinsert the flash card.
Error Message%MEDIA-FLASHFS_HES-1-COND_PROBLEM Could not [chars] condition variable : Error [chars]
Explanation Possibly condition variable does not exist
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-1-DRIVER_UNAVAILABLE Flash driver unavailable
Explanation Flash device driver process is dead.
Recommended Action Restrt the flash device driver process.
Error Message%MEDIA-FLASHFS_HES-1-INIT_FAILED Flash device initialization failed. Error: [chars]
Explanation Something wen't wrong.
Recommended Action Kill the flash file system and restart it. If that fails Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-1-MUTEX_PROBLEM Could not [chars] mutex : Error [chars]
Explanation Possibly mutex does not exist
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-BAD_DEVICE_DATA [chars]: Bank Status Error. Shutting down device
Explanation Bad device data
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-BAD_DRIVER_WAIT_THREAD Could not start the thread to wait for driver after driver crash
Explanation Could not start a thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-BAD_PULSE_ATTACH [chars]: resmgr_pulse_attach failed: [text]
Explanation Could not attach pulse for flash driver death detection
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-BAD_THREAD_CREATE Could not start the [chars] thread
Explanation Could not start a thread.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-BADCARD [chars]: The flash card seems to be corrupted
Explanation Probably the flash card is corrupted
Recommended Action Format the flash card
Error Message%MEDIA-FLASHFS_HES-3-BADCHANNEL [chars]: can't create channel
Explanation Could not create channel for the resource manager
Recommended Action Reboot the router if possible. If not try to start it from the command line. If that too fails Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-BADDLLOPEN [chars]: [chars] [chars] Could not open DLL
Explanation DLL Probably not Loaded
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-BADDLSYM [chars]: [chars] [chars] Can't Resolve symbol
Explanation Proabaly Function not Defined in DLL
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-BADHDR [chars]: Hdr Error, ptr=[hex]
Explanation A file with a bad header encountered on flash
Recommended Action No action is required.
Error Message%MEDIA-FLASHFS_HES-3-BADSTATUS [chars]: Bank Status Error. Shutting down device
Explanation Either device is in error or file system format can not be recognized.
Recommended Action If possible format the device. If not Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information..
Error Message%MEDIA-FLASHFS_HES-3-CONNECT_FAILED Could not establish connected to channel [dec]
Explanation Could not create channel for the resource manager
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-DEBUG_INIT_FAILED [chars]
Explanation Internal error
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-DRIVER_CHANGED Underyling flash card seems to have changed. Closing file
Explanation Probably the driver died or the flash card has been swapped (OIR). The flash card has changed. The current access seems to be for a file which has been opened with the driver for old card.
Recommended Action No action is required.
Error Message%MEDIA-FLASHFS_HES-3-EVENT_BLOCK_ERROR event_block failed -[chars]
Explanation --
Recommended Action --
Error Message%MEDIA-FLASHFS_HES-3-EVENT_MGR_CREATE_FAILED [chars]: can't create channel-[chars]
Explanation Could not create channel for the event manager
Recommended Action Reboot the router if possible. If not try to start it from the command line. If that too fails Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-FAIL_DEBUG_REG can't connect to configuration, [chars]
Explanation Flash debugging service register to sysdb failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-RECOVERY_FROM_SQUEEZE_FAILED Flash device could not recover from interrupted sqeeze. Error: [dec]
Explanation Something wen't wrong.
Recommended Action Kill the flash file system and restart it. If that fails Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-SYMLINK_EXPORT [chars]: unable to export mount point ([chars])
Explanation Device will not be accessible from all nodes.
Recommended Action Kill the flash file system and restart it. If that fails Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-3-SYSMGR_PROC_READY_FAILED sysmgr_proc_ready failed - [chars]
Explanation Failed to send message to Sysmgr about init completion.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-4-BAD_DRIVER_PULSE_REGISTRATION Could not register a pulse with the driver
Explanation We register pulse with the driver so that we get notification of certain events. For some reason it did not work.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-4-BAD_SECTOR_ERASE Sector [unsigned long int] not erased
Explanation Bad sector
Recommended Action No action is required.
Error Message%MEDIA-FLASHFS_HES-4-CARD_WRITE_PROTECTED [chars]: The flash card is write protected
Explanation The card is write protected, and a write operation is attempted
Recommended Action No action is required.
Error Message%MEDIA-FLASHFS_HES-4-EXCLUSIVE_ACCESS_DENIED Could not get exclusive access to the device
Explanation Possibly a read or write is still going on in the background
Recommended Action No action is required.
Error Message%MEDIA-FLASHFS_HES-4-UNKNOWN_PULSE Unknown pulse received. Code: [dec], Value [dec]:
Explanation An unexpected pulse has been received
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FLASHFS_HES-5-CARD_SWAPPED [chars]: The flash card has been swapped (OIR)
Explanation The pcmcia flash card has been pulled out from its slot and re-inserted with a same or different card
Recommended Action No action is required.
Error Message%MEDIA-FLASHFS_HES-6-DRIVER_BACK_UP Flash driver [chars] back up
Explanation Flash device driver process came back up.
Recommended Action No action is required.
Error Message%MEDIA-FLASHFS_HES-6-RECOVERING_FROM_SQUEEZE Flash device [chars] trying to recover from interrupted squeeze. Please wait
Explanation Squeeze is used to recover space consumed by deleted files in flash file systems. A deleted file is just marked deleted and space occupied by it is not recovered till a squeeze is done. The flash card has been ejected or router crashed in while performing squeeze. We are trying to recover from that.
Recommended Action No action is required.
Error Message%MEDIA-FLASHFS_HES-6-RECOVERING_FROM_SQUEEZE_DONE Flash device [chars] recovered from interrupted squeeze
Explanation Squeeze is used to recover space consumed by deleted files in flash file systems. A deleted file is just marked deleted and space occupied by it is not recovered till a squeeze is done. The flash card has been ejected or router crashed in while performing squeeze. We are able to succesfully recover from that and flash is usable again.
Recommended Action No action is required.
Error Message%MEDIA-FLASHFS_HES-6-USAGE [chars]: Usage -m -d
Explanation Arguments for invoking the flash file system. is the mount location of the flash file system and is the path name of the driver to be used by the file system. Wrong arguments have been used. Please use the correct ones.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
FSDEVINFO Messages
Error Message%MEDIA-FSDEVINFO-3-DBG_CLEANUP Failed to unregister the debug's
Explanation During total cleanup fs_dev_info failed to unregister the debugs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FSDEVINFO-3-EVM_ERROR [chars], Error: [chars]
Explanation Failed in some event management functions.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FSDEVINFO-3-GET_FILESYS_ERR platform_get_fslist() failed, could not retrieve list of File Systems
Explanation The api platform_get_fslist() returned NULL pointer instead of the list.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FSDEVINFO-3-LWM_ERROR [chars], Error: [chars]
Explanation Failed to execute some LWM library functions.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FSDEVINFO-3-MAIN_INIT_ERROR Initialization in main failed, Error: [chars]
Explanation One of the functions called during initialization of the process failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FSDEVINFO-3-NO_MEMORY Failed in allocating memory, [chars]
Explanation Not enough memory available in the system.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FSDEVINFO-3-OIR_REG_FAIL Could not register for OIR events. Error [hex]
Explanation fs_dev_info server was unable to register for OIR events from PCMCIAD
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FSDEVINFO-3-REGISTER_ERROR Could not register [chars]
Explanation Failed to register Error description DLL.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FSDEVINFO-3-SIGNAL_RELATED [chars], Error: [chars]
Explanation Some signal related function returned with an error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FSDEVINFO-3-SYSDB_CONNECT_FAIL Could not connect to sysdb
Explanation During total cleanup fs_dev_info failed to unregister the debugs.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FSDEVINFO-3-SYSMGR_READY Could not inform sysmgr that process is ready, Error: [chars]
Explanation The main function failed to inform sysmgr that it is ready.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-FSDEVINFO-3-THREAD_ERROR [chars], Error: [chars]
Explanation One of the pthread_* functions returned with an error.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
GT_BFLASH_DRIVER Messages
Error Message%MEDIA-GT_BFLASH_DRIVER-4-ERR_OPTION [chars]: invalid option [char]
Explanation Wrong usage to start the flash driver resource manager.
Recommended Action 'Start the driver with the correct options'
Error Message%MEDIA-GT_BFLASH_DRIVER-4-ERR_USAGE [chars]: Usage -m -d
Explanation Wrong usage to start the flash driver resource manager.
Recommended Action 'Start the driver with the correct options'
Error Message%MEDIA-GT_BFLASH_DRIVER-7-ERR_DETECT_BOARD Failed to detect board type
Explanation Platform library unable to determine hardware board type.
Recommended Action 'Check software revison and/or ID EEPROM programming'
Error Message%MEDIA-GT_BFLASH_DRIVER-7-UNKNOWN_BOARD_STATE Unsupported board detected: [chars]
Explanation Platform library unable to determine hardware board type.
Recommended Action 'Check software revison and/or ID EEPROM programming'
HARDDISK Messages
Error Message%MEDIA-HARDDISK-3-MALLOC_FAIL [chars]
Explanation Memory allocation failed
Recommended Action 'Attempt to clear event manager'
Error Message%MEDIA-HARDDISK-3-SPAWN_FAIL Failed to spawn [chars]
Explanation Failed to spawn mount helper process
Recommended Action 'Check for harddisk mount point'
Error Message%MEDIA-HARDDISK-3-SYSMGR_REGISTER_FAIL [chars]
Explanation Unable to register with sysmgr for node state change.
Recommended Action 'Check mount point of hd'
Error Message%MEDIA-HARDDISK-4-GET_NODE_FAIL [chars]
Explanation Unable to get node state.
Recommended Action 'Clear event manager'
Error Message%MEDIA-HARDDISK-7-MUTEX_LOCK Failed to lock [chars]
Explanation A required mutex lock failed.
Recommended Action 'Mutex used by other process'
Error Message%MEDIA-HARDDISK-7-MUTEX_UNLOCK Failed to unlock [chars]
Explanation A required mutex unlock failed.
Recommended Action 'HD process has mutex'
Error Message%MEDIA-HARDDISK-7-UNKNOWN_MACHINE [chars]
Explanation Unable to find the machine type.
Recommended Action 'Check ID EEPROM programmed correctly'
Error Message%MEDIA-HARDDISK-7-UNSUPPORTED_BOARD [[dec]] not supported
Explanation Unsupported Board type.
Recommended Action 'Check ID EEPROM programmed correctly'
MB_FLASH_LIB Messages
Error Message%MEDIA-MB_FLASH_LIB-1-BADCHANNEL Can't Create Channel
Explanation Could not create channel for the resource manager
Recommended Action Reboot the router if possible. If not try to start it from the command line. If that too fails Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-MB_FLASH_LIB-1-BADPATH Can't Attach Pathname [chars]
Explanation Could not attach pathname
Recommended Action Reboot the router if possible. If not try to start it from the command line. If that too fails Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-MB_FLASH_LIB-7-VERIFYINFO %Error: verify @ [hex]-expected [hex], read [hex]
Explanation Verify information due to verbose option
Recommended Action No action is required.
NVRAM_PLATFORM_COMMON Messages
Error Message%MEDIA-NVRAM_PLATFORM_COMMON-3-BAD_CHECKSUM nvram is corrupt - textptr: [hex], textsize: [dec], textbase: [hex], chksum in nvram: [dec], newchksum: [dec], oldchksum: [dec]
Explanation nvram corrupt.
Recommended Action If need to use classic configs, boot an appropriate classic image and rewrite the config. If not No action is required..
Error Message%MEDIA-NVRAM_PLATFORM_COMMON-3-BAD_CLASSIC_CONFIG Unexpected version of classic configuration memory ([dec])
Explanation Classic configuration different version than expected
Recommended Action If need to use classic configs, boot an appropriate classic image and rewrite the config. If not No action is required.
Error Message%MEDIA-NVRAM_PLATFORM_COMMON-3-BAD_CLASSIC_CONFIG_COMPRESS Couldn't uncompress config ([dec])
Explanation Decompress of Compressed Classic Config Failed
Recommended Action If need to use classic configs, boot an appropriate classic image and rewrite the config. If not No action is required..
Error Message%MEDIA-NVRAM_PLATFORM_COMMON-3-BAD_CLASSIC_CONFIG_MEM Bad classic configuration memory structure
Explanation Nvptr corrupted
Recommended Action If need to use classic configs, boot an appropriate classic image and rewrite the config. If not No action is required.
Error Message%MEDIA-NVRAM_PLATFORM_COMMON-3-LOGGING_ERROR Error while logging nvram activity: [[chars]]
Explanation Error while logging nvram activity
Recommended Action No action is required.
Error Message%MEDIA-NVRAM_PLATFORM_COMMON-4-WRITE_ABORT A write to the nvram was aborted
Explanation A Write to nvram was aborted.
Recommended Action Recovery will be attempted in the driver. Otherwise format nvram using command - erase nvram: format
NVRAM_PLATFORM Messages
Error Message%MEDIA-NVRAM_PLATFORM-4-BAD_NVRAM_MAP Could not map nvram
Explanation Mapping of Nvram Failed
Recommended Action 'Check for 2MB size NVRAM'
Error Message%MEDIA-NVRAM_PLATFORM-4-BATTERY_LOW NVRAM low battery
Explanation Detect NVRAM low battery state, the data stored in NVRAM may be destroyed after power down the board whit battery low state.
Recommended Action 'NVRAM Battery may need to be replaced'
Error Message%MEDIA-NVRAM_PLATFORM-7-BAD_NVRAM_VAR ROMMON variable-value pair: [chars], contains illegal (non-printable)characters
Explanation Could not allocate memory for a DRAM buffer
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-NVRAM_PLATFORM-7-ERROR_REG_PM Warning: Failed register NVRAM to platform manager
Explanation pm_fault_register_device() API return error
Recommended Action No action is required.
Error Message%MEDIA-NVRAM_PLATFORM-7-ERROR_RUN_BMON Warning: Failed running NVRAM battery monitor thread
Explanation pthread_create() returns error
Recommended Action No action is required.
Error Message%MEDIA-NVRAM_PLATFORM-7-NVRAM_SIZE_ZERO Warning: NVRAM size is 0
Explanation Possible error during sizing nvram, the NVRAM may not exist
Recommended Action 'Check if formatted and present'
NVRAM_UTIL Messages
Error Message%MEDIA-NVRAM_UTIL-3-DEBUG_INIT_FAILED [chars]
Explanation Debug init failed
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-NVRAM_UTIL-3-FAIL_DEBUG_REG [chars]: Can't connect to configuration, [chars]
Explanation NVRAM debugging service register to sysdb failed.
Recommended Action Check the existence of the Sysdb service. The system is supposed to re-register if the Sysdb service is available.
NVRAM Messages
Error Message%MEDIA-NVRAM-3-BADDLLOPEN [chars]: [chars] [chars] Could not open DLL
Explanation DLL Probably not Loaded
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-NVRAM-3-BADDLSYM [chars]: [chars] [chars] Can't Resolve symbol
Explanation Proabaly Function not Defined in DLL
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-NVRAM-3-BADFUNCTIONS [chars]: Undefined Functions in DLL
Explanation Some Required Functions have not been Defined in DLL
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-NVRAM-3-BADINIT [chars]: Nvram Initialization Failed
Explanation Could not get the geometry of NVRAM. NVRAM may not exist
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%MEDIA-NVRAM-3-BADMEM Nvram RM could not be started
Explanation Could not get enough memory for NVRAM RM.
Recommended Action 'Router running low in memory. Reboot if possible.'
Error Message%MEDIA-NVRAM-3-CONNECT_FAILED Could not establish connected to channel [dec]
Explanation Could not create channel for the resource manager
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-NVRAM-3-CORRUPT Corrupt nvram. Format with erase nvram: format
Explanation Nvram corrupt
Recommended Action 'Format nvram'
Error Message%MEDIA-NVRAM-3-EVENT_BLOCK_ERROR event_block error -- [chars]
Explanation Error during event block
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message%MEDIA-NVRAM-3-FORMATERROR [chars]: could not auto format corrupted NVRAM, error: [chars]
Explanation Probably the NVRAM device has gone bad.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-NVRAM-3-nospace Nvram out of space
Explanation nvram full
Recommended Action Delete unwanted files
Error Message%MEDIA-NVRAM-3-RECOVERED [chars]: [chars]
Explanation The NVRAM device corruption fixed.
Recommended Action No action is required.
Error Message%MEDIA-NVRAM-4-BADFILES NVRAM File Corrupted ([chars]). Some of them May be Lost
Explanation Files Overwritten by Another Image, or Router Crashed
Recommended Action No action is required.
Error Message%MEDIA-NVRAM-6-OPEN_DUMP_PATH [chars]: dump file path: [chars]
Explanation Informational message indicating the nvram dump file path.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-NVRAM-6-OPENERROR [chars]: Open for path [chars] failed, error: [chars], [chars]
Explanation Check the state of the device pointed by path. Device may be inaccessible.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-NVRAM-7-BADPATH [chars]: Can't Attach Pathname /dev/nvram
Explanation Could not attach pathname
Recommended Action Reboot the router if possible. If not try to start it from the command line. If that too fails Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-NVRAM-7-EVENT_MGR_CREATE_FAILED Could not create event manager for [chars]: [chars]
Explanation Failed to create event manager for the process
Recommended Action Try to start it from the command line. If that too fails Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
SYNCFS2 Messages
Error Message%MEDIA-SYNCFS2-3-FAILURE [chars] [chars]: [chars]
Explanation Syncfs failure
Recommended Action Contact customer support
Error Message%MEDIA-SYNCFS2-3-INIT_FAILED Failed to initialize module [chars] because [chars] and cannot continue.
Explanation Syncfs failed to initialize a module.
Recommended Action Contact customer support
Error Message%MEDIA-SYNCFS2-3-REGISTER_NTFN Failed to register with [chars] for notification
Explanation Syncfs failed to register with qsm/lrd for notification
Recommended Action Contact customer support
Error Message%MEDIA-SYNCFS2-3-STBY_SYMLINK Failed to create link to Standby card: [chars]
Explanation Syncfs failed to create required links to the standby card. Syncfs unable to mirror any files to the standby card.
Recommended Action Contact customer support
Error Message%MEDIA-SYNCFS2-3-STBY_SYMLINK_NOTYET Symbolic Links to Standby root is not published yet.
Explanation Syncfs noticed that required symbolic-links to the standby card, is not published yet. Syncfs will get notified when they are available.
Recommended Action Contact customer support
Error Message%MEDIA-SYNCFS2-7-CLIENT_ERR [chars]: [chars]
Explanation Failed function call.
Recommended Action Contact customer support
Error Message%MEDIA-SYNCFS2-7-LOST_SYNC Unable to replicate [chars] [chars] to standby card because [chars]
Explanation Syncfs failed to transfer the specified file to the standby card.
Recommended Action Ensure there is sufficient disk space on standby card's filesystems, and that all removeable media is correctly inserted. Once resolved, power cycle the standby card using 'hw-module slot X shut' and 'no hw-module slot X shut' to resume synchronization.
Error Message%MEDIA-SYNCFS2-7-LRD_AVAILABLE Standby has become AVAILABLE - START SYNC
Explanation The Standby card has been inserted and sync will be started
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-SYNCFS2-7-LRD_NOTAVAILABLE Standby has been rendered UNAVAILABLE - STOP SYNC
Explanation The Standby card has been either removed or put down by admin
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-SYNCFS2-7-LRD_PARTNER_AVAILABLE Standby has become AVAILABLE. LRD returned partner-node - START SYNC
Explanation The Standby card has been inserted and sync will be started
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message%MEDIA-SYNCFS2-7-MUTEX_LOCK Failed to lock mutex [chars]
Explanation A required mutex lock failed.
Recommended Action Contact customer support
Error Message%MEDIA-SYNCFS2-7-MUTEX_TEST_LOCK Mutex [chars] was found unlocked
Explanation A mutex which should have been locked was tested and found unlocked
Recommended Action Contact customer support
Error Message%MEDIA-SYNCFS2-7-MUTEX_UNLOCK Failed to unlock a mutex [chars]
Explanation A required mutex unlock failed.
Recommended Action Contact customer support
Error Message%MEDIA-SYNCFS2-7-REPLICATE_FAIL Replication of [chars] [chars] failed: [chars] -- Retry will be attempted.
Explanation Syncfs failed to replicate file/dir, it will retry it again.
Recommended Action Contact customer support
SYNCFS2LIB Messages
Error Message%MEDIA-SYNCFS2LIB-6-LOST_SYNC File [chars] lost synchronization to standby card
Explanation Syncfs failed to transfer a file to the standby card. If a card failover occurs, some data may be lost.
Recommended Action None
Error Message%MEDIA-SYNCFS2LIB-7-MUTEX_LOCK Failed to lock mutex for file [chars]
Explanation A required mutex lock failed.
Recommended Action Contact customer support
Error Message%MEDIA-SYNCFS2LIB-7-MUTEX_TEST_LOCK Mutex for file [chars] was found unlocked
Explanation A mutex which should have been locked was tested and found unlocked
Recommended Action Contact customer support
Error Message%MEDIA-SYNCFS2LIB-7-MUTEX_UNLOCK Failed to unlock mutex for file [chars]
Explanation A required mutex unlock failed.
Recommended Action Contact customer support