Cisco IOS XR System Error Reference Guide for XR1200 Series Platform Specific Messages, Release 3.3 - Packet Infrastructure Messages [Cisco IOS XR Software (End-of-Sale)]

Table Of Contents

Packet Infrastructure Messages

C12000_FWD_CLIENT_DLL Messages

ENCAP_RM Messages

ENCAP Messages

FM Messages

FWD_EDGE_ADJ Messages

FWD_HAL Messages

FWD_NETIO_DLL Messages

PLATFORM_C12000_NETIO_LIB Messages

PLATFORM_LPTS_COM_IFIB Messages

PLATFORM_LPTS_COM_NETIO Messages

PLATFORM_LPTS_PIFIB Messages

PLATFORM_PFI Messages

TNODE Messages

Packet Infrastructure Messages

This section contains all Packet Infrastructure related System Error Messages, including ifmgr, tunnels, bundlemgr, pakman, and so forth. The following facility codes are represented in this module:

•C12000_FWD_CLIENT_DLL Messages

•ENCAP_RM Messages

•ENCAP Messages

•FM Messages

•FWD_EDGE_ADJ Messages

•FWD_HAL Messages

•FWD_NETIO_DLL Messages

•PLATFORM_C12000_NETIO_LIB Messages

•PLATFORM_LPTS_COM_IFIB Messages

•PLATFORM_LPTS_COM_NETIO Messages

•PLATFORM_LPTS_PIFIB Messages

•PLATFORM_PFI Messages

•TNODE Messages

C12000_FWD_CLIENT_DLL Messages
Error Message     
%PKT_INFRA-C12000_FWD_CLIENT_DLL-3-ERR [chars][dec]
Explanation An error occured in the forwarder netio client dll (possible the plim driver)
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

ENCAP_RM Messages
Error Message     
%PKT_INFRA-ENCAP_RM-3-FATAL_ERR Fatal error: [chars]: Err=[dec]
Explanation A fatal error occurred in L2 Encap String RM which involves exiting the process.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-ENCAP_RM-3-MSG_SEND_FAILED encap_rm: msg: [dec], retried: [dec] time(s), failed to send, errno: [chars]
Explanation Unable to send a message to the L2 Encap String RM server.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-ENCAP_RM-3-NONFATAL_ERR Nonfatal error: [chars]: Err=[dec]
Explanation This is a error message in the L2 Encap String RM to indicate anomalies which are not FATAL. Some of the messages may indicate a failure to allocate resources needed by applications. In many cases these messages must not keep appearing after the temporary situation is resolved.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-ENCAP_RM-3-OOR Failed to insert L2 encapsulation string. Out of resource condition reached.
Explanation A request to insert a L2 encapsulation string into the encapsulation table has failed due to out of resource condition.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-ENCAP_RM-6-INFO_MSG Info: [chars]
Explanation This is an informational message in the L2 Encap String RM.
Recommended Action No action is required.

ENCAP Messages
Error Message     
%PKT_INFRA-ENCAP-3-DEBUG_INIT_EVENT_FAILED [chars]: debug_init_event([chars]) failed error [chars]
Explanation Failed to switch ON debug event for encapsulation package.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message     
%PKT_INFRA-ENCAP-3-DEBUG_REGISTER_FAILED [chars]: debug_register() failed error [chars]
Explanation Failed to register debug events for encapsulation package.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message     
%PKT_INFRA-ENCAP-3-FAILURE [chars]
Explanation Failure in c12000/aib component.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message     
%PKT_INFRA-ENCAP-3-SYSDB_BIND_FAILED sysdb_bind failed [hex], [chars]

Explanation Failed to bind to sysdb.
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message     
%PKT_INFRA-ENCAP-3-SYSDB_REGISTER_FAILED Failed to register for notification ,[[hex]] [chars]

Explanation Failed to register with Sydb for item change notification
Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'

FM Messages
Error Message     
%PKT_INFRA-FM-3-INIT_ERROR Process initialization failed: ([chars]%s)
Explanation The feature manager (feat_mgr) process failed to initialize. This process programs packet classification hardware for features which require an action to be performed based on the packet classification. If the feat_mgr process fails to initialize, the access control list cannot be programmed into the hardware. %s - indicates the reason for the initialization failure. %s - is the decoded error reason.
Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times when this error is encountered, to recover. Execute 'show process feat_mgr location 0/x/cpu0' to verify that the process is up and running. If it is still non-operational, try doing 'process restart feat_mgr location 0/x/cpu0'. Collect all debug information if the process is continually restarting: 'debug featmgr error location 0/x/cpu0'. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FWD_EDGE_ADJ Messages
Error Message     
%PKT-INFRA-FWD_EDGE_ADJ-2-EDGE_ADJ_ERR GSR edge adj dll layer internal error [chars] : [chars]
Explanation A runtime error occurred in GSR adj's egine layer. The reason for the failure is displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

FWD_HAL Messages
Error Message     
%PKT-INFRA-FWD_HAL-2-ACCESSOR Failed to access [chars] field of [chars] object, error: [dec] [chars]
Explanation A runtime error occurred while trying to access the specified field of the specified object in the Platform Independent SW Data Structures. The reason for the failure is also displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-ADJ_ERR GSR adj internal error: [chars]
Explanation A runtime error occurred in GSR adj module.The reason for the failure is also displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-BACKWALK_ERR Backwalk on [dec] object due to [chars] event failed, error: [dec] [chars]
Explanation A runtime error occurred while trying to walk and update dependent objects in the forwarding chain. The reason for the failure is also displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-FASTCONV_CLI_ERR FastConvergence CLI: [chars], error: [chars]
Explanation A runtime error occurred while apply the Fast convergence CLI. The reason for the failure is also displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-HW_OCE_NULL [chars] - GSR HAL internal error: hal object ([chars]) getting a NULL hw_oce
Explanation A runtime error occurred in GSR MPLS module.The reason for the failure is also displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-INIT [chars], error: [dec] [chars]
Explanation A runtime error occurred while initalizing GSR Hardware Abstraction Layer (HAL) module. The reason for the failure is displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-INVALID_PARENT_OBJ GSR FIB internal error: [chars] failed to get parent [chars] obj - [chars]
Explanation A runtime error occurred in GSR FIB module.The reason for the failure is also displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-LDI_ERR GSR loadinfo internal error: [chars]
Explanation A runtime error occurred in GSR loadinfo module.The reason for the failure is also displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-PFX_ERR GSR prefix internal error: [chars]
Explanation A runtime error occurred in GSR prefix module.The reason for the failure is also displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-SHMWIN_ERR [chars], error: [dec] [chars]
Explanation A runtime error occurred while operating on a shared memory window. The reason for the failure is displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-STATS_INTF_REGISTER Failed to register interface [hex] with Stats module, error: [dec] [chars]
Explanation A runtime error occurred while trying to register the specified interface with Stats module for stats collection. The reason for the failure is also displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-STATS_INTF_UNREGISTER Failed to unregister interface [hex] from Stats module, error: [dec] [chars]
Explanation A runtime error occurred while trying to unregister the specified interface from Stats module for stats collection. The reason for the failure is also displayed. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-STATS_VALIDATION Stats validation error: [chars] ([dec]): [chars]
Explanation A validation error occurred while doing an LSP/TE statistics operation. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-UNSUPT_TERMINATE Forwarding requested unsupported platform HW resource recovery and platform is forcing line card reset to recover hardware resources
Explanation The FIB encountered an unrecoverable error afer one or more crashes. It is attempting to purge all hardware and software resources before starting a clean initialization. The platform does not support hardware resource recovery and is resetting the line card to recover all hardware resources. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-2-USED_BY_BGP_STATUS_CHANGE Used by BGP status changed from [chars] to [chars] on obj 0x[pointer]
Explanation Used by BGP status on the loadinfo changed. This is not generally expected and config needs to be examined to understand the cause. Please call Cisco Support with the error information.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT-INFRA-FWD_HAL-6-FASTCONVERGENCE_CLI_INFO WARNING: This command will take effect only after reloading the node. Please reload the node using the command hw-module reload location r/s/CPU0
Explanation This command will take effect only after reloading the node. Please reload the node using the command hw-module reload location r/s/CPU0
Please reload the node using the command hw-module reload location r/s/CPU0

FWD_NETIO_DLL Messages
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-ATTACH_FAILED fwd: netio idb attach failed for plim interface: [hex].
Explanation FWD was not able to attach to plim interface .
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-BAD_COMMAND_RESULT fwd: received bad command result for buffer request: [hex]
Explanation FWD received a bad command result for BMA free buffer request
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-BMA_OUT_OF_SEQUENCE fwd: BMA buffer request/response sequence number mismatch - received [dec], expected [dec]
Explanation FWD received an out of sequence BMA buffer request response
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-FATAL fwd: fatal error encountered, reason=[chars]
Explanation Null Driver partner encountered a fatal error and is not able recover from the error. A reason text will be supplied call support with this text.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-FATAL_2 fwd: fatal error encountered, reason=[chars], errno=[dec]
Explanation fwd encountered a fatal error and is not able to recover from the error. A reason text will be supplied call support with this text. An integer errno will also be printed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-GET_CTX_ERR Failed to get idb ctx for port [dec], error - ([dec])
Explanation FWD driver got a packet but couldn't map a port to an idb context
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-IDB_CTX_NULL FWD idb context for port [hex] is NULL!
Explanation While processing an ingress packet, the fwd driver failed to find idb context
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-INCORRECT_IDB fwd: looking for plim interface: [hex], netio gave us: [hex].
Explanation FWD was supplied with a plim interface that does not have an idb yet.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-INFO fwd: service degrading error, reason = [chars]
Explanation The fwd encountered an error that would lead to degraded service.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-INVALID_PLIM_PORT fwd: invalid plim port for plim interface: [hex]
Explanation FWD was supplied with a plim port that exceeds the limit of num ports.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-MALLOC_FAILED fwd: fatal memory allocation error for bytes
Explanation FWD encountered a fatal memory allocation error
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-MISSING_IDB fwd: plim interface: [hex] does not have a netio idb.
Explanation FWD was supplied with a plim interface that does not have an idb yet.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-MUTEXOPFAIL [chars]: Mutex [chars] operation failed on [chars]; reason [chars]
Explanation The packet subsystem failed to get mutex.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-NETIO_IDB_UNAVAILABLE netio idb for interface [hex] not found, dropping packet 0x[pointer]
Explanation While processing an ingress packet, the fwd driver failed to find netio idb
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-NO_OUTSTANDING_BMA_REQ fwd: received BMA buffer request response with no outstanding request
Explanation FWD received a BMA interrupt indicating a response to a BMA buffer request but there was no request made
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-NOT_YET_IMPLEMENTED fwd: this function is not yet implemented
Explanation FWD, a function was not implemented.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-QAD_EGRESS_Q_LOOKUP_ERR Failed to find netio egress qad queue. dropping packet 0x[pointer]
Explanation While transmitting a packet down to the fabric, couldn't find the egress queue
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-QAD_Q_PRODUCE_FAILED Failed to populate netio egress queue, error - [chars]
Explanation FWD driver failed to populate qad netio egress queue
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-QAD_RX_THREAD_ERR Failed to create forwarder qad rx thread, error - [chars]
Explanation FWD driver failed to create qad rx thread
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message     
%PKT_INFRA-FWD_NETIO_DLL-3-SET_INPUT_IF_ERR Failed to set input interface handle [hex] on packet
Explanation While processing an ingress packet, the fwd driver failed to set input interface
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

PLATFORM_C12000_NETIO_LIB Messages
Error Message     
%PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-FINT_IDB_NOT_FOUND Failed to obtain netio idb for FINT interface
Explanation The FINT idb is not yet created in netio. This could be a transient condition.
Recommended Action Please capture the following information and if traffic loss also is being observed Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show logging show proc blocked
Error Message     
%PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-FINT_IDB_NOT_FOUND Failed to obtain netio idb for FINT interface
Explanation The FINT idb is not yet created in netio. This could be a transient condition.
Recommended Action Please capture the following information and if traffic loss also is being observed Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show logging show proc blocked
Error Message     
%PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-GET_MYNODEID_FAIL Failed to obtain my node id [chars]
Explanation Unable to determine my node id using platform api.
Recommended Action Please capture show proc ouput and show logging output - 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message     
%PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-GET_MYNODEID_FAIL Failed to obtain my node id [chars]
Explanation Unable to determine my node id using platform api.
Recommended Action Please capture show proc ouput and show logging output - 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.'
Error Message     
%PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-GET_PPINDEX_INFO_FAIL Lookup for ppindex([dec]), pp_proto([dec]), failed due to [chars]
Explanation Unable to get the adjacency and next hop information from given ppindex.
Recommended Action Please capture the following information and if traffic loss also is being observed Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show logging show proc blocked

PLATFORM_LPTS_COM_IFIB Messages
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_MISSING_FLOW [chars]: Flow type '[chars]' not configured
Explanation error in IFIB flow handling configuration. The named flow type was not explicitly configured and will have default characteristics applied.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_MISSING_PARAMETER [chars]: Missing parameter after '[chars]' in flow '[chars]'
Explanation Syntax error in IFIB flow handling configuration. The named flow type may have default characteristics applied.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_UNKNOWN_KEYWORD [chars]: Unknown keyword '[chars]' in flow '[chars]'
Explanation Syntax error in IFIB flow handling configuration. The named flow type may have default characteristics applied.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_UNKNOWN_PARAMETER [chars]: Unknown parameter '[chars]' after '[chars]' in flow '[chars]'
Explanation Syntax error in IFIB flow handling configuration. The named flow type may have default characteristics applied.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-NO_CONFIG [chars]: Missing configuration for IFIB flow handling
Explanation No configuration for IFIB flow handling was found. Default characteristics will be used for all packets.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-NO_CONFIG_MEMORY [chars]: Insufficient memory for IFIB flow handling configuration
Explanation Insufficient memory was available for storing the IFIB flow handling configuration. Default characteristics will be used for all packets.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-7-DEBUG_CLEANUP [chars]: Debug cleanup failed: [chars]
Explanation An error was returned when calling debug_cleanup() function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-7-DEBUG_INIT_EVENT [chars]: Debug initialization for the lpts/[chars] event failed: [chars]
Explanation An error was returned when calling the debug_init_event() function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_IFIB-7-DEBUG_REGISTER [chars]: Debug registration failed: [chars]
Explanation An error was returned when calling debug_register() function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

PLATFORM_LPTS_COM_NETIO Messages
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_CLEANUP [chars]: Debug cleanup failed: [chars]
Explanation An error was returned when calling debug_cleanup() function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_INIT_EVENT [chars]: Debug initialization for the lpts/[chars] event failed: [chars]
Explanation An error was returned when calling the debug_init_event() function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_REGISTER [chars]: Debug registration failed: [chars]
Explanation An error was returned when calling debug_register() function.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

PLATFORM_LPTS_PIFIB Messages
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-BACKEND_EDM [chars]: EDM backend function [chars] failed: [chars]
Explanation An internal EDM backend function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-BAG [chars]: Bag function [chars] failed: [chars]
Explanation An internal bag function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CHKPT_INIT [chars]: Checkpoint Initialization function [chars] failed: [chars]
Explanation An internal Checkpoint function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_FLOW_MEMORY [chars]: Insufficient memory for flow configuration
Explanation There is insufficient memory for the flow configuration. All flows will be assigned default characteristics.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_MISSING_FLOW [chars]: Flow type '[chars]' not configured
Explanation error in PIFIB flow handling configuration. The named flow type was not explicitly configured and will have default characteristics applied.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_MISSING_PARAMETER [chars]: Missing parameter after '[chars]' in flow '[chars]'
Explanation Syntax error in PIFIB flow handling configuration. The named flow type may have default characteristics applied.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_MEMORY [chars]: Insufficient memory for policer configuration
Explanation There is insufficient memory for the policer configuration. All flows will be assigned default characteristics.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_PARAMETER_INVALID [chars]: Invalid parameter '[chars]' after '[chars]' in policer '[dec]' definition
Explanation There is an invalid parameter after a keyword in a policer definition. The policer may be assigned default characterstics.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_PARAMETER_MISSING [chars]: Missing parameter after '[chars]' in policer '[dec]' definition
Explanation There is a missing required parameter after a keyword in a policer definition. The policer may be assigned default characterstics.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_UNKNOWN_KEYWORD [chars]: Unknown keyword '[chars]' in policer '[dec]' definition
Explanation There is an unknown keyword in a policer definition. The policer may be assigned default characterstics.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_UNDEFINED_POLICER [chars]: flow '[chars]' references undefined policer '[dec]'
Explanation An input flow definition references an undefined policer. The flow will be configured to use policer 0.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_UNKNOWN_KEYWORD [chars]: Unknown keyword '[chars]' in flow '[chars]'
Explanation Syntax error in PIFIB flow handling configuration. The named flow type may have default characteristics applied.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_UNKNOWN_PARAMETER [chars]: Unknown parameter '[chars]' in flow '[chars]'
Explanation Syntax error in PIFIB flow handling configuration. The named flow type may have default characteristics applied.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-EVENT_CONN_CREATE [chars]: could not create event connection: [chars]
Explanation An internal error was detected when trying to create event connection.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-EVENT_CONN_OPEN [chars]: could not open event connection: [chars]
Explanation An internal error was detected when trying to open event connection.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_ADD_FEAT2GRP [chars]: fm add feat to group failed for ISIS [chars]
Explanation An internal fm add feature to group function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_ADD_IFH2GRP [chars]: fm add ifh to group failed for ISIS [chars]
Explanation An internal fm add ifh to group function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_CREATE_GROUP [chars]: fm create group failed: [chars]
Explanation An internal fm create group function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_FEAT_PROCESSING [chars]: fm feature registration failed: [chars]
Explanation An internal fm feature registration function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_REGISTER [chars]: fm_register failed: [chars]
Explanation An internal fm_register function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-HFA_REGISTER [chars]: hfa_register failed: [chars]
Explanation An internal hfa_register function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-LTRACE_INIT [chars]: ltrace_init2 failed: [chars]
Explanation An internal ltrace_init2 function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-MSG_ATTACH [chars]: Event Mgr function [chars] failed: [chars]
Explanation An internal Event Manager function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-NO_CONFIG [chars]: Missing configuration for PIFIB flow handling
Explanation No configuration for PIFIB flow handling was found. Default characteristics will be used for all packets.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-SHOW_EDM_CLOSE [chars]: Cleanup for EDM failed: [chars]
Explanation Cleanup for EDM failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-SHOW_EDM_INIT [chars]: Initialization for show EDM failed: [chars]
Explanation Initialization for show EDM failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-SYSDB [chars]: Sysdb function [chars] failed: [chars]
Explanation An internal sysdb function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-3-TCAM_FMT_TO_HFA_MAP [chars]: vmr_builder_program_tcam_fmt_from_hfa_map failed: [chars]
Explanation An tcam format to hfa mapping function failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-DEBUG_CLEANUP [chars]: Debug cleanup failed: [chars]
Explanation An error was returned when cleaning up debug.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-DEBUG_INIT_EVENT [chars]: Debug initialization for the lpts/[chars] event failed: [chars]
Explanation An error was returned when initializing debug.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-PLATFORM_LPTS_PIFIB-7-DEBUG_REGISTER [chars]: Debug registration failed: [chars]
Explanation An error was returned when registering debug.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

PLATFORM_PFI Messages
Error Message     
%PKT_INFRA-PLATFORM_PFI-4-IFHANDLE_DECODE Could not map handle [hex] to slot
Explanation The interface handle cannot be mapped to a slot on the card.
Recommended Action Debug message only. *DEBUG*
Error Message     
%PKT_INFRA-PLATFORM_PFI-4-INIT Failed to initialise [chars]
Explanation An error occured when a module was going to be initialised. This may cause the process to terminate.
Recommended Action Restarting the process might help.

TNODE Messages
Error Message     
%PKT_INFRA-TNODE-3-CAPS_LOOKUP Capsulation lookup failed : [chars]
Explanation im_caps_lookup() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-CHAN_CREATE Failed to create channel : [chars]
Explanation Failed to create a channel using event_manager_create.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-EVENT_INIT IM to initialize linecard dpf notification event : [chars]
Explanation event_init_event() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-GET_RP_SLOT Failed to get RP slot number : [chars]
Explanation primary_rp_slot_number() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-IF_FIND Failed to obtain interface handle ([chars]) : [chars]
Explanation im_interface_find() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-IM_CTRLSVR_BIND Failed to bind to IM control server : [chars]
Explanation im_control_server_bind() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-IM_DATAPATH_CTRL IM datapath control failed : [chars]
Explanation im_caps_datapath_control() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-IM_DATASVR_BIND Failed to bind to IM data server : [chars]
Explanation im_data_server_bind() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-LC_CONN_CREATE Failed to create transit-node lc connection : [chars]
Explanation event_conn_create() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-LC_CONN_OPEN Failed to open transit-node lc connection : [chars]
Explanation event_conn_open() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-PROC_RDY Failed to notify System Manager (Ready) : [chars]
Explanation sysmgr_proc_ready() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-SYSDB_BIND Failed to bind to SysDB : [chars]
Explanation sysdb_bind() call failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-SYSDB_COID Failed to obtain the file descriptor from SysDB connection : [chars]
Explanation sysdb_conn_to_coid() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%PKT_INFRA-TNODE-3-SYSDB_REG Failed to register for notification for dpf events : [chars]
Explanation sysdb_register_notification() failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.

	Cisco IOS XR System Error Reference Guide for XR1200 Series Platform Specific Messages, Release 3.3
	Packet Infrastructure Messages
Cisco IOS XR System Error Reference Guide for XR1200 Series Platform Specific Messages, Release 3.3 Preface Overview Fabric Messages ASIC Fabric Interface Messages High Availability (HA) Messages Installation Messages Internet Protocol (IP) Messages Layer 1 (L1) Messages Layer 2 (L2) Messages Line Card (LC) Messages Media Messages Manageability (MGBL) Messages Operating System (OS) Messages Packet Infrastructure Messages Platform Messages Quality of Service (QOS) Messages Routing Messages	Download this chapter Packet Infrastructure Messages Download the complete book Book-level PDF: Cisco IOS XR Sytem Error Reference Guide for XR12000 Series Platform Specific Messages (PDF - 2 MB) Feedback Table Of Contents Packet Infrastructure Messages C12000_FWD_CLIENT_DLL Messages ENCAP_RM Messages ENCAP Messages FM Messages FWD_EDGE_ADJ Messages FWD_HAL Messages FWD_NETIO_DLL Messages PLATFORM_C12000_NETIO_LIB Messages PLATFORM_LPTS_COM_IFIB Messages PLATFORM_LPTS_COM_NETIO Messages PLATFORM_LPTS_PIFIB Messages PLATFORM_PFI Messages TNODE Messages Packet Infrastructure Messages This section contains all Packet Infrastructure related System Error Messages, including ifmgr, tunnels, bundlemgr, pakman, and so forth. The following facility codes are represented in this module: •C12000_FWD_CLIENT_DLL Messages •ENCAP_RM Messages •ENCAP Messages •FM Messages •FWD_EDGE_ADJ Messages •FWD_HAL Messages •FWD_NETIO_DLL Messages •PLATFORM_C12000_NETIO_LIB Messages •PLATFORM_LPTS_COM_IFIB Messages •PLATFORM_LPTS_COM_NETIO Messages •PLATFORM_LPTS_PIFIB Messages •PLATFORM_PFI Messages •TNODE Messages C12000_FWD_CLIENT_DLL Messages Error Message %PKT_INFRA-C12000_FWD_CLIENT_DLL-3-ERR [chars][dec] Explanation An error occured in the forwarder netio client dll (possible the plim driver) Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. ENCAP_RM Messages Error Message %PKT_INFRA-ENCAP_RM-3-FATAL_ERR Fatal error: [chars]: Err=[dec] Explanation A fatal error occurred in L2 Encap String RM which involves exiting the process. Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-ENCAP_RM-3-MSG_SEND_FAILED encap_rm: msg: [dec], retried: [dec] time(s), failed to send, errno: [chars] Explanation Unable to send a message to the L2 Encap String RM server. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-ENCAP_RM-3-NONFATAL_ERR Nonfatal error: [chars]: Err=[dec] Explanation This is a error message in the L2 Encap String RM to indicate anomalies which are not FATAL. Some of the messages may indicate a failure to allocate resources needed by applications. In many cases these messages must not keep appearing after the temporary situation is resolved. Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-ENCAP_RM-3-OOR Failed to insert L2 encapsulation string. Out of resource condition reached. Explanation A request to insert a L2 encapsulation string into the encapsulation table has failed due to out of resource condition. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-ENCAP_RM-6-INFO_MSG Info: [chars] Explanation This is an informational message in the L2 Encap String RM. Recommended Action No action is required. ENCAP Messages Error Message %PKT_INFRA-ENCAP-3-DEBUG_INIT_EVENT_FAILED [chars]: debug_init_event([chars]) failed error [chars] Explanation Failed to switch ON debug event for encapsulation package. Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.' Error Message %PKT_INFRA-ENCAP-3-DEBUG_REGISTER_FAILED [chars]: debug_register() failed error [chars] Explanation Failed to register debug events for encapsulation package. Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.' Error Message %PKT_INFRA-ENCAP-3-FAILURE [chars] Explanation Failure in c12000/aib component. Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.' Error Message %PKT_INFRA-ENCAP-3-SYSDB_BIND_FAILED sysdb_bind failed [hex], [chars] Explanation Failed to bind to sysdb. Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.' Error Message %PKT_INFRA-ENCAP-3-SYSDB_REGISTER_FAILED Failed to register for notification ,[[hex]] [chars] Explanation Failed to register with Sydb for item change notification Recommended Action 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.' FM Messages Error Message %PKT_INFRA-FM-3-INIT_ERROR Process initialization failed: ([chars]%s) Explanation The feature manager (feat_mgr) process failed to initialize. This process programs packet classification hardware for features which require an action to be performed based on the packet classification. If the feat_mgr process fails to initialize, the access control list cannot be programmed into the hardware. %s - indicates the reason for the initialization failure. %s - is the decoded error reason. Recommended Action The System Manager process (sysmgr) will automatically respawn this process, up to a fixed number of times when this error is encountered, to recover. Execute 'show process feat_mgr location 0/x/cpu0' to verify that the process is up and running. If it is still non-operational, try doing 'process restart feat_mgr location 0/x/cpu0'. Collect all debug information if the process is continually restarting: 'debug featmgr error location 0/x/cpu0'. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. FWD_EDGE_ADJ Messages Error Message %PKT-INFRA-FWD_EDGE_ADJ-2-EDGE_ADJ_ERR GSR edge adj dll layer internal error [chars] : [chars] Explanation A runtime error occurred in GSR adj's egine layer. The reason for the failure is displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. FWD_HAL Messages Error Message %PKT-INFRA-FWD_HAL-2-ACCESSOR Failed to access [chars] field of [chars] object, error: [dec] [chars] Explanation A runtime error occurred while trying to access the specified field of the specified object in the Platform Independent SW Data Structures. The reason for the failure is also displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-ADJ_ERR GSR adj internal error: [chars] Explanation A runtime error occurred in GSR adj module.The reason for the failure is also displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-BACKWALK_ERR Backwalk on [dec] object due to [chars] event failed, error: [dec] [chars] Explanation A runtime error occurred while trying to walk and update dependent objects in the forwarding chain. The reason for the failure is also displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-FASTCONV_CLI_ERR FastConvergence CLI: [chars], error: [chars] Explanation A runtime error occurred while apply the Fast convergence CLI. The reason for the failure is also displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-HW_OCE_NULL [chars] - GSR HAL internal error: hal object ([chars]) getting a NULL hw_oce Explanation A runtime error occurred in GSR MPLS module.The reason for the failure is also displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-INIT [chars], error: [dec] [chars] Explanation A runtime error occurred while initalizing GSR Hardware Abstraction Layer (HAL) module. The reason for the failure is displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-INVALID_PARENT_OBJ GSR FIB internal error: [chars] failed to get parent [chars] obj - [chars] Explanation A runtime error occurred in GSR FIB module.The reason for the failure is also displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-LDI_ERR GSR loadinfo internal error: [chars] Explanation A runtime error occurred in GSR loadinfo module.The reason for the failure is also displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-PFX_ERR GSR prefix internal error: [chars] Explanation A runtime error occurred in GSR prefix module.The reason for the failure is also displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-SHMWIN_ERR [chars], error: [dec] [chars] Explanation A runtime error occurred while operating on a shared memory window. The reason for the failure is displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-STATS_INTF_REGISTER Failed to register interface [hex] with Stats module, error: [dec] [chars] Explanation A runtime error occurred while trying to register the specified interface with Stats module for stats collection. The reason for the failure is also displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-STATS_INTF_UNREGISTER Failed to unregister interface [hex] from Stats module, error: [dec] [chars] Explanation A runtime error occurred while trying to unregister the specified interface from Stats module for stats collection. The reason for the failure is also displayed. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-STATS_VALIDATION Stats validation error: [chars] ([dec]): [chars] Explanation A validation error occurred while doing an LSP/TE statistics operation. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-UNSUPT_TERMINATE Forwarding requested unsupported platform HW resource recovery and platform is forcing line card reset to recover hardware resources Explanation The FIB encountered an unrecoverable error afer one or more crashes. It is attempting to purge all hardware and software resources before starting a clean initialization. The platform does not support hardware resource recovery and is resetting the line card to recover all hardware resources. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-2-USED_BY_BGP_STATUS_CHANGE Used by BGP status changed from [chars] to [chars] on obj 0x[pointer] Explanation Used by BGP status on the loadinfo changed. This is not generally expected and config needs to be examined to understand the cause. Please call Cisco Support with the error information. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT-INFRA-FWD_HAL-6-FASTCONVERGENCE_CLI_INFO WARNING: This command will take effect only after reloading the node. Please reload the node using the command hw-module reload location r/s/CPU0 Explanation This command will take effect only after reloading the node. Please reload the node using the command hw-module reload location r/s/CPU0 Please reload the node using the command hw-module reload location r/s/CPU0 FWD_NETIO_DLL Messages Error Message %PKT_INFRA-FWD_NETIO_DLL-3-ATTACH_FAILED fwd: netio idb attach failed for plim interface: [hex]. Explanation FWD was not able to attach to plim interface . Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-BAD_COMMAND_RESULT fwd: received bad command result for buffer request: [hex] Explanation FWD received a bad command result for BMA free buffer request Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-BMA_OUT_OF_SEQUENCE fwd: BMA buffer request/response sequence number mismatch - received [dec], expected [dec] Explanation FWD received an out of sequence BMA buffer request response Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-FATAL fwd: fatal error encountered, reason=[chars] Explanation Null Driver partner encountered a fatal error and is not able recover from the error. A reason text will be supplied call support with this text. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-FATAL_2 fwd: fatal error encountered, reason=[chars], errno=[dec] Explanation fwd encountered a fatal error and is not able to recover from the error. A reason text will be supplied call support with this text. An integer errno will also be printed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-GET_CTX_ERR Failed to get idb ctx for port [dec], error - ([dec]) Explanation FWD driver got a packet but couldn't map a port to an idb context Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-IDB_CTX_NULL FWD idb context for port [hex] is NULL! Explanation While processing an ingress packet, the fwd driver failed to find idb context Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-INCORRECT_IDB fwd: looking for plim interface: [hex], netio gave us: [hex]. Explanation FWD was supplied with a plim interface that does not have an idb yet. Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-INFO fwd: service degrading error, reason = [chars] Explanation The fwd encountered an error that would lead to degraded service. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-INVALID_PLIM_PORT fwd: invalid plim port for plim interface: [hex] Explanation FWD was supplied with a plim port that exceeds the limit of num ports. Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-MALLOC_FAILED fwd: fatal memory allocation error for bytes Explanation FWD encountered a fatal memory allocation error Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-MISSING_IDB fwd: plim interface: [hex] does not have a netio idb. Explanation FWD was supplied with a plim interface that does not have an idb yet. Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-MUTEXOPFAIL [chars]: Mutex [chars] operation failed on [chars]; reason [chars] Explanation The packet subsystem failed to get mutex. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-NETIO_IDB_UNAVAILABLE netio idb for interface [hex] not found, dropping packet 0x[pointer] Explanation While processing an ingress packet, the fwd driver failed to find netio idb Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-NO_OUTSTANDING_BMA_REQ fwd: received BMA buffer request response with no outstanding request Explanation FWD received a BMA interrupt indicating a response to a BMA buffer request but there was no request made Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-NOT_YET_IMPLEMENTED fwd: this function is not yet implemented Explanation FWD, a function was not implemented. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-QAD_EGRESS_Q_LOOKUP_ERR Failed to find netio egress qad queue. dropping packet 0x[pointer] Explanation While transmitting a packet down to the fabric, couldn't find the egress queue Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-QAD_Q_PRODUCE_FAILED Failed to populate netio egress queue, error - [chars] Explanation FWD driver failed to populate qad netio egress queue Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-QAD_RX_THREAD_ERR Failed to create forwarder qad rx thread, error - [chars] Explanation FWD driver failed to create qad rx thread Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. Error Message %PKT_INFRA-FWD_NETIO_DLL-3-SET_INPUT_IF_ERR Failed to set input interface handle [hex] on packet Explanation While processing an ingress packet, the fwd driver failed to set input interface Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration. PLATFORM_C12000_NETIO_LIB Messages Error Message %PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-FINT_IDB_NOT_FOUND Failed to obtain netio idb for FINT interface Explanation The FINT idb is not yet created in netio. This could be a transient condition. Recommended Action Please capture the following information and if traffic loss also is being observed Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show logging show proc blocked Error Message %PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-FINT_IDB_NOT_FOUND Failed to obtain netio idb for FINT interface Explanation The FINT idb is not yet created in netio. This could be a transient condition. Recommended Action Please capture the following information and if traffic loss also is being observed Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show logging show proc blocked Error Message %PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-GET_MYNODEID_FAIL Failed to obtain my node id [chars] Explanation Unable to determine my node id using platform api. Recommended Action Please capture show proc ouput and show logging output - 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.' Error Message %PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-GET_MYNODEID_FAIL Failed to obtain my node id [chars] Explanation Unable to determine my node id using platform api. Recommended Action Please capture show proc ouput and show logging output - 'Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.' Error Message %PKT_INFRA-PLATFORM_C12000_NETIO_LIB-4-GET_PPINDEX_INFO_FAIL Lookup for ppindex([dec]), pp_proto([dec]), failed due to [chars] Explanation Unable to get the adjacency and next hop information from given ppindex. Recommended Action Please capture the following information and if traffic loss also is being observed Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. show logging show proc blocked PLATFORM_LPTS_COM_IFIB Messages Error Message %PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_MISSING_FLOW [chars]: Flow type '[chars]' not configured Explanation error in IFIB flow handling configuration. The named flow type was not explicitly configured and will have default characteristics applied. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_MISSING_PARAMETER [chars]: Missing parameter after '[chars]' in flow '[chars]' Explanation Syntax error in IFIB flow handling configuration. The named flow type may have default characteristics applied. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_UNKNOWN_KEYWORD [chars]: Unknown keyword '[chars]' in flow '[chars]' Explanation Syntax error in IFIB flow handling configuration. The named flow type may have default characteristics applied. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-CONFIG_UNKNOWN_PARAMETER [chars]: Unknown parameter '[chars]' after '[chars]' in flow '[chars]' Explanation Syntax error in IFIB flow handling configuration. The named flow type may have default characteristics applied. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-NO_CONFIG [chars]: Missing configuration for IFIB flow handling Explanation No configuration for IFIB flow handling was found. Default characteristics will be used for all packets. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_COM_IFIB-3-NO_CONFIG_MEMORY [chars]: Insufficient memory for IFIB flow handling configuration Explanation Insufficient memory was available for storing the IFIB flow handling configuration. Default characteristics will be used for all packets. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_COM_IFIB-7-DEBUG_CLEANUP [chars]: Debug cleanup failed: [chars] Explanation An error was returned when calling debug_cleanup() function. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_COM_IFIB-7-DEBUG_INIT_EVENT [chars]: Debug initialization for the lpts/[chars] event failed: [chars] Explanation An error was returned when calling the debug_init_event() function. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_COM_IFIB-7-DEBUG_REGISTER [chars]: Debug registration failed: [chars] Explanation An error was returned when calling debug_register() function. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. PLATFORM_LPTS_COM_NETIO Messages Error Message %PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_CLEANUP [chars]: Debug cleanup failed: [chars] Explanation An error was returned when calling debug_cleanup() function. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_INIT_EVENT [chars]: Debug initialization for the lpts/[chars] event failed: [chars] Explanation An error was returned when calling the debug_init_event() function. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_COM_NETIO-7-DEBUG_REGISTER [chars]: Debug registration failed: [chars] Explanation An error was returned when calling debug_register() function. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. PLATFORM_LPTS_PIFIB Messages Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-BACKEND_EDM [chars]: EDM backend function [chars] failed: [chars] Explanation An internal EDM backend function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-BAG [chars]: Bag function [chars] failed: [chars] Explanation An internal bag function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CHKPT_INIT [chars]: Checkpoint Initialization function [chars] failed: [chars] Explanation An internal Checkpoint function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_FLOW_MEMORY [chars]: Insufficient memory for flow configuration Explanation There is insufficient memory for the flow configuration. All flows will be assigned default characteristics. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_MISSING_FLOW [chars]: Flow type '[chars]' not configured Explanation error in PIFIB flow handling configuration. The named flow type was not explicitly configured and will have default characteristics applied. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_MISSING_PARAMETER [chars]: Missing parameter after '[chars]' in flow '[chars]' Explanation Syntax error in PIFIB flow handling configuration. The named flow type may have default characteristics applied. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_MEMORY [chars]: Insufficient memory for policer configuration Explanation There is insufficient memory for the policer configuration. All flows will be assigned default characteristics. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_PARAMETER_INVALID [chars]: Invalid parameter '[chars]' after '[chars]' in policer '[dec]' definition Explanation There is an invalid parameter after a keyword in a policer definition. The policer may be assigned default characterstics. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_PARAMETER_MISSING [chars]: Missing parameter after '[chars]' in policer '[dec]' definition Explanation There is a missing required parameter after a keyword in a policer definition. The policer may be assigned default characterstics. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_POLICER_UNKNOWN_KEYWORD [chars]: Unknown keyword '[chars]' in policer '[dec]' definition Explanation There is an unknown keyword in a policer definition. The policer may be assigned default characterstics. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_UNDEFINED_POLICER [chars]: flow '[chars]' references undefined policer '[dec]' Explanation An input flow definition references an undefined policer. The flow will be configured to use policer 0. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_UNKNOWN_KEYWORD [chars]: Unknown keyword '[chars]' in flow '[chars]' Explanation Syntax error in PIFIB flow handling configuration. The named flow type may have default characteristics applied. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-CONFIG_UNKNOWN_PARAMETER [chars]: Unknown parameter '[chars]' in flow '[chars]' Explanation Syntax error in PIFIB flow handling configuration. The named flow type may have default characteristics applied. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-EVENT_CONN_CREATE [chars]: could not create event connection: [chars] Explanation An internal error was detected when trying to create event connection. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-EVENT_CONN_OPEN [chars]: could not open event connection: [chars] Explanation An internal error was detected when trying to open event connection. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_ADD_FEAT2GRP [chars]: fm add feat to group failed for ISIS [chars] Explanation An internal fm add feature to group function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_ADD_IFH2GRP [chars]: fm add ifh to group failed for ISIS [chars] Explanation An internal fm add ifh to group function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_CREATE_GROUP [chars]: fm create group failed: [chars] Explanation An internal fm create group function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_FEAT_PROCESSING [chars]: fm feature registration failed: [chars] Explanation An internal fm feature registration function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-FM_REGISTER [chars]: fm_register failed: [chars] Explanation An internal fm_register function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-HFA_REGISTER [chars]: hfa_register failed: [chars] Explanation An internal hfa_register function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-LTRACE_INIT [chars]: ltrace_init2 failed: [chars] Explanation An internal ltrace_init2 function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-MSG_ATTACH [chars]: Event Mgr function [chars] failed: [chars] Explanation An internal Event Manager function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-NO_CONFIG [chars]: Missing configuration for PIFIB flow handling Explanation No configuration for PIFIB flow handling was found. Default characteristics will be used for all packets. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-SHOW_EDM_CLOSE [chars]: Cleanup for EDM failed: [chars] Explanation Cleanup for EDM failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-SHOW_EDM_INIT [chars]: Initialization for show EDM failed: [chars] Explanation Initialization for show EDM failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-SYSDB [chars]: Sysdb function [chars] failed: [chars] Explanation An internal sysdb function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-3-TCAM_FMT_TO_HFA_MAP [chars]: vmr_builder_program_tcam_fmt_from_hfa_map failed: [chars] Explanation An tcam format to hfa mapping function failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-7-DEBUG_CLEANUP [chars]: Debug cleanup failed: [chars] Explanation An error was returned when cleaning up debug. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-7-DEBUG_INIT_EVENT [chars]: Debug initialization for the lpts/[chars] event failed: [chars] Explanation An error was returned when initializing debug. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-PLATFORM_LPTS_PIFIB-7-DEBUG_REGISTER [chars]: Debug registration failed: [chars] Explanation An error was returned when registering debug. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. PLATFORM_PFI Messages Error Message %PKT_INFRA-PLATFORM_PFI-4-IFHANDLE_DECODE Could not map handle [hex] to slot Explanation The interface handle cannot be mapped to a slot on the card. Recommended Action Debug message only. DEBUG Error Message %PKT_INFRA-PLATFORM_PFI-4-INIT Failed to initialise [chars] Explanation An error occured when a module was going to be initialised. This may cause the process to terminate. Recommended Action Restarting the process might help. TNODE Messages Error Message %PKT_INFRA-TNODE-3-CAPS_LOOKUP Capsulation lookup failed : [chars] Explanation im_caps_lookup() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-CHAN_CREATE Failed to create channel : [chars] Explanation Failed to create a channel using event_manager_create. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-EVENT_INIT IM to initialize linecard dpf notification event : [chars] Explanation event_init_event() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-GET_RP_SLOT Failed to get RP slot number : [chars] Explanation primary_rp_slot_number() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-IF_FIND Failed to obtain interface handle ([chars]) : [chars] Explanation im_interface_find() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-IM_CTRLSVR_BIND Failed to bind to IM control server : [chars] Explanation im_control_server_bind() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-IM_DATAPATH_CTRL IM datapath control failed : [chars] Explanation im_caps_datapath_control() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-IM_DATASVR_BIND Failed to bind to IM data server : [chars] Explanation im_data_server_bind() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-LC_CONN_CREATE Failed to create transit-node lc connection : [chars] Explanation event_conn_create() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-LC_CONN_OPEN Failed to open transit-node lc connection : [chars] Explanation event_conn_open() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-PROC_RDY Failed to notify System Manager (Ready) : [chars] Explanation sysmgr_proc_ready() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-SYSDB_BIND Failed to bind to SysDB : [chars] Explanation sysdb_bind() call failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-SYSDB_COID Failed to obtain the file descriptor from SysDB connection : [chars] Explanation sysdb_conn_to_coid() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %PKT_INFRA-TNODE-3-SYSDB_REG Failed to register for notification for dpf events : [chars] Explanation sysdb_register_notification() failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
	Terms & Conditions \| Privacy Statement \| Cookie Policy \| Trademarks