Cisco IOS XR System Error Reference Guide for Platform Independent Messages, Release 3.3 - Quality of Service (QOS) Messages [Cisco IOS XR Software (End-of-Sale)]

Table Of Contents

Quality of Service (QoS) Messages

CLASSIFY Messages

FQ_QOS Messages

MARK_QOS Messages

QOS_CLASSIFY_NETIO Messages

QOS_FIFO Messages

QOS_RC_QOSMGR Messages

QOS_TXM Messages

QOS_WRED Messages

QOS Messages

Quality of Service (QoS) Messages

This section contains all Quality of Service related System Error Messages. The following facility codes are represented in this module:

•CLASSIFY Messages

•FQ_QOS Messages

•MARK_QOS Messages

•QOS_CLASSIFY_NETIO Messages

•QOS_FIFO Messages

•QOS_RC_QOSMGR Messages

•QOS_TXM Messages

•QOS_WRED Messages

•QOS Messages

CLASSIFY Messages
Error Message     
%QOS-CLASSIFY-4-MATCH_NOT_SUPPORTED Matching based on [chars] is not supported on [chars].
Explanation Matching based on the configured criterion is not supported in the specified direction. Reconfigure the policy map so that the specified match feature clause is removed and then reapply the service policy.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-CLASSIFY-4-TOO_MANY_CLASSES Policymap '[chars]' contains [dec] classmaps, which exceeds the maximum supported
Explanation The number of class-maps configured for the specified policy exceeds the currently supported maximum. Currently, the maximum number of supported classes is 32.
Recommended Action Reconfigure the policy map so that it contains fewer than 32 classes, and reapply the service policy. The total number of class-maps for a policy-map includes both the number of specifically configured class-maps as well as the number of class-maps configured for all of its child policies, plus the default class, if not already configured.
Error Message     
%QOS-CLASSIFY-7-DEBUG_INIT_ERROR An error occurred during debug initialization, err: [chars]
Explanation The QoS Classify DLL encountered an error during debug initialization. This is not a critical error. The QoS classification feature will function properly, but will not be able to use any of the debugging facilities.
Recommended Action None

FQ_QOS Messages
Error Message     
%QOS-FQ_QOS-3-CAPS_ADD_FAIL Cannot add FQ capsulation to the data plane. Error code= [chars]
Explanation QoS Manager failed to add capsulation for Fair Queueing to the the data plane.
Recommended Action Turn on debugs with the following command debug qos control all dev and reapply the configuration command that caused the failure.
Error Message     
%QOS-FQ_QOS-4-BUNDLE_BW_NOPCT Absolute bw specified for bundle interfaces, use percentage values instead
Explanation Bandwidth for a bundle interfaces must be specified in percentage values instead of absolute values.
Recommended Action Modify the bandwidth parameter to specify percentage instead of absolute values and then reapply the configuration.
Error Message     
%QOS-FQ_QOS-4-BW_EXCEED Sum of allocated[chars] bandwidth exceeds the maximum
Explanation The sum of the reserved bandwidth configured in the policy-map exceeds the maximum bandwidth for the interface.
Recommended Action Correct the policymap so that the sum of reserved bandwidth is less than the maximum for the interface, and then reapply the service policy.
Error Message     
%QOS-FQ_QOS-4-BW_REMAINING_PRIORITY_ERROR Remaining Bandwidth and Priority can not be configured under the same class
Explanation Remaining Bandwidth and priority can not be configured under the same policy.
Recommended Action Reconfigure the policy-map so that one of the features is removed and then reapply the service policy.
Error Message     
%QOS-FQ_QOS-4-INVALID_UNIT An invalid or incompatible unit '[chars]' ([dec]) was specified for [chars].
Explanation An invalid unit has been specified for the feature mentioned in the message.
Recommended Action Modify the configuration parameter so that the specified unit is compatible with the feature and platform.
Error Message     
%QOS-FQ_QOS-4-MAX_CLASSES_EXCEEDED Number of classes exceeds the maximum number of classes allowed in a single policy map
Explanation The number of class maps configured on the applied policy map exceeds the maximum allowed.
Recommended Action Reconfigure the policy map so that the number of class-maps is reduced below the maximum allowed number and then reapply the policy.
Error Message     
%QOS-FQ_QOS-4-MIN_BW_ERROR Configured minimum bandwidth ([dec] kbps) is greater than the configured shape bandwidth ([dec] kbps) for class '[chars]'
Explanation The specified minimum bandwidth is greater than the shape bandwidth.
Recommended Action Correct the configuration so that minimum bandwidth is less than the shape(maximum) bandwidth, and reapply the service policy.
Error Message     
%QOS-FQ_QOS-4-NO_L1_BW_ERROR Level1 has no bandwidth guarantee. So cannot specify level2 bandwidth guarantee.
Explanation A level 2 class has been configured with a bandwidth guarantee without the level 1 class having a bandwidth guarantee
Recommended Action Reconfigure the policy-map so that the level 1 class includes a bandwidth guarantee and then reapply the service policy
Error Message     
%QOS-FQ_QOS-4-SHAPE_BW_EXCEED Shape bandwidth exceeds 100 percent of the interface bandwidth
Explanation The configured shaping bandwidth exceeds the maximum bandwidth for the interface.
Recommended Action Correct the configuration so that shape bandwidth is less than or equal to the interface bandwidth.
Error Message     
%QOS-FQ_QOS-4-VALUE_TOO_LARGE The value specified for [chars] is too large and cannot be handled by the system
Explanation The configured value for the feature mentioned in the message is too large.
Recommended Action Use a value which is less than 4294967295 kbps or KBytes (depending on the type of parameter configured).
Error Message     
%QOS-FQ_QOS-5-PRIORITY_ERROR Shaping and Priority can not be configured under the same class
Explanation Shape and priority can not be configured under the same class.
Recommended Action Reconfigure the policy-map so that one of the features, either priority, or shaping is removed and then reapply the service policy.
Error Message     
%QOS-FQ_QOS-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QOS FQ dll encountered an error while initializing the debug facility. This is not a fatal error. QOS Fair Queueing will continue to execute properly, but will not be able to use the debugging facility.
Recommended Action None
Error Message     
%QOS-FQ_QOS-7-ERR_MEM_ALLOC Memory alloc error [chars]
Explanation The router cannot allocate more memory while performing the specified task. This condition occurs only when the system is low on memory.
Recommended Action None

MARK_QOS Messages
Error Message     
%QOS-MARK_QOS-5-NOT_SUPPORTED Marking of [chars] on egress interface not supported
Explanation Marking of given attribute is not supported on the egress direction.
Recommended Action Please modify the policy-map so that the specified marking option is not included in the policy-map configuration.
Error Message     
%QOS-MARK_QOS-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QOS Mark component encounterd an error while initializing the debug facility. This is not a fatal error. QOS Marking will continue to execute properly, but will not be able to use the debuging facility.
Recommended Action None

QOS_CLASSIFY_NETIO Messages
Error Message     
%QOS-QOS_CLASSIFY_NETIO-7-DEBUG_INIT_ERROR A error occurred during debug initialization. Error: [chars]
Explanation The QoS Classify DLL encountered an error while initializing the debug facility. This is not a fatal error. QoS Classify will continue to execute properly, but will not be able to use the debugging facility.
Recommended Action None

QOS_FIFO Messages
Error Message     
%QOS-QOS_FIFO-7-DEBUG_INIT_ERROR An error occurred during debug initialization. Error: [chars]
Explanation The QoS FIFO dll encountered a problem while initializingg the debug facility. This is not a fatal error. QoS FIFO will continue to execute properly, but will not be able to use the debugging facility.
Recommended Action None
Error Message     
%QOS-QOS_FIFO-7-DEBUG_INIT_ERROR An error occurred during debug initialization, err: [chars]
Explanation The FIFO QoSMgr component encountered an error during debug initialization This is not a fatal condition. FIFO queueuing will work properly but will not be able to use any of the debugging facilities.
Recommended Action None

QOS_RC_QOSMGR Messages
Error Message     
%QOS-QOS_RC_QOSMGR-4-INVALID_UNIT An invalid or incompatible unit '[chars]' ([dec]) was specified for [chars]
Explanation An invalid unit has been specified for the feature mentioned in the message.
Recommended Action Correct the policy-map so that a correct unit value is specified for the feature being configured
Error Message     
%QOS-QOS_RC_QOSMGR-4-NOT_SUPPORTED Action [chars] not supported on [chars]
Explanation The policy has an action that is not supported .
Recommended Action Correct the policy-map to correct the action to a supported action.
Error Message     
%QOS-QOS_RC_QOSMGR-4-RC_BUNDLE_BW_NOPCT Absolute bw specified for bundle interfaces, use percentage values instead
Explanation For bundle interfaces, the bandwidth must be specified in percentage values of absolute values.
Recommended Action Correct the policy-map so that the bandwidth value is specified as a percentage of the total bandwidth and then reapply the policy-map
Error Message     
%QOS-QOS_RC_QOSMGR-4-RC_BW_EXCEED Policer rate exceeds 100 percent of the interface bandwidth
Explanation The Policer rate in the policy-map exceeds the maximum bandwidth that the interface can support.
Recommended Action Correct the policy-map so that the policer rate is smaller than the maximum of the interface it has been applied to.
Error Message     
%QOS-QOS_RC_QOSMGR-4-VALUE_TOO_LARGE The value specified for [chars] is too large and cannot be handled by the system
Explanation The value configured for the feature mentioned in the message is too large.
Recommended Action Use a value which is less than 4294967295 kbps or KBytes (depending on the type of parameter configured).
Error Message     
%QOS-QOS_RC_QOSMGR-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QoSMgr policer component encountered an error during debug initialization This is not a fatal condition. Policing will work properly but will not be able to use any of the debugging facilities.
Recommended Action None

QOS_TXM Messages
Error Message     
%QOS-QOS_TXM-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QOS Mark process encounterd an error while initializing the debug facility. This is not a fatal error. QOS Marking will continue to execute properly, but will not be able to use the debuging facility.
Recommended Action None
Error Message     
%QOS-QOS_TXM-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QOS TXM process encountered an error while initializing the debug facility. This is not a fatal error. QOS TXM will continue to execute properly, but will not be able to use the debugging facility.
Recommended Action None
Error Message     
%QOS-QOS_TXM-7-UNINITIALISE_ERROR An error occurred in initialization sequence for iface: [chars]
Explanation The QOS TXM process encountered an error in its initialsation sequence. This is a serious error. QOS TXM functioning correctly is not guranteed depending upon the exact problem in initialisation sequence
Recommended Action None

QOS_WRED Messages
Error Message     
%QOS-QOS_WRED-7-DEBUG_INIT_ERROR An error occurred during debug initialization. Error: [chars]
Explanation The QoS WRED dll encountered a problem while initializing the debug facility. This is not a fatal error. QoS WRED will continue to execute properly, but will not be able to use the debugging facility.
Recommended Action None
Error Message     
%QOS-QOS_WRED-7-INVALID_WRED_TYPE The type of random-detect configured under class '[chars]' is invalid or not supported on this platform. Please configure a supported random-detect type.
Explanation An invalid type of random-detect was configured for the class specified in the message.
Recommended Action Please reconfigure the policy-map with a supported type of random-detect. If the configured type of random-detect is supported on this platform and this message is seen, please contact the customer support with the following information.

QOS Messages
Error Message     
%QOS-QOS-3-DLL_INIT_FAIL Could not initialize [chars] dll. Error code - [chars]
Explanation An error was encountered while trying to initialize a DLL that supports a given feature. Both the DLL name and the error code are displayed. This is a critical error in the QOS component. It indicates that the DLL that implements a feature does not provide an initializing function. This indicates that some QOS feature is not working properly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-FEATURE_ADD_FAIL Failed to add policy [chars], class = [chars], feature = [chars].
Explanation Failed to add the specified feature while applying the specified service policy.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-FILE_ERROR File [chars] error: [chars]. Reason: [chars]
Explanation An error was encountered while accessing a file. Both the file name and the error reason are displayed. This is a critical error in the QOS component. It indicates that the file that defines a feature is missing from the system and the related QOS feature will not work properly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-FILE_WRONG_INFO File [chars] [chars] [dec]
Explanation An error was encountered while accessing a file. Both the file name and the error reason are displayed. This is a critical error in the QOS component. It indicates that the file that defines a feature is missing from the system and the related QOS feature will not working properly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-FT_REMOVE_FAIL Failed to remove the feature [chars]. Error code - [chars]
Explanation The QOS Manager process failed to remove the specified feature. The error code is also displayed.
Recommended Action Please turn on debugs using the following command: debug qos control all dev and reenter the configuration command that caused the error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-FT_SEND_FAIL Sending control to [chars] feature failed
Explanation Failed to send a control feature information to the Execution Agent. The name of the feature is displayed.
Recommended Action Please turn on debugs using the following command: debug qos control all dev and reenter the configuration command that caused the error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-MGR_DLL_OPEN_FAIL Could not open [chars] DLL. Error code - [chars]
Explanation An error was encountered while trying to open a DLL that supports a given feature. Both the DLL name and the error code are displayed. This is a critical error in the QOS component. It indicates that the DLL that implements the feature is not present in the system. This indicates that some QOS feature is not working properly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-MSG_SEND_FAIL Failed to send message to feature [chars] [chars]. Error code - [chars]
Explanation Failed to send the a message to the specified feature due to the error message displayed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-4-NODE_INSTL_FAIL Could not install [chars] feature [chars]
Explanation An error was encountered while trying to add the specified feature node to NetIO. Both the feature name and the error code are displayed. This is a critical error in the QOS component. It indicates that some QOS feature is not working properly.
Recommended Action Please provide the output of the commands: Please provide the output of the commands: show running configuration show qos trace
Error Message     
%QOS-QOS-6-FT_CONFIGURE_FAIL Failed to configure feature [chars]. Error code - [chars]
Explanation The specified feature could not be configured due to the specified reason.
Recommended Action None
Error Message     
%QOS-QOS-6-HPOLICY_ATTACH_FAIL Too many levels of hierarchy in policy [chars].
Explanation The Policy could not be installed because it has more than 2 levels of hierarchy.
Recommended Action Simplify the policy-map to include no more than 2 levels of hierarchy. and reapply it.
Error Message     
%QOS-QOS-6-POLICY_ATTACH_FAIL Service policy [chars] could not be attached to [chars]. Error code - [chars]
Explanation Policy could not be installed. The reason is displayed.
Recommended Action Please verify that the specified policy has been configured with the following command: show running configuration
Error Message     
%QOS-QOS-7-CLASSMAP_NOT_FOUND Class map [chars] not found
Explanation The specified class map was not found. Make sure that it is properly configured. If not, please confifure it.
Recommended Action Verify that the specified class-map name is properly configured by issuing the following command show running class-map
Error Message     
%QOS-QOS-7-DLL_REGISTER_CERR_FAIL Could not register error codes for [chars] dll. Error code - [chars]
Explanation Could not get register DLL error codes. This is not a critical error. The QOS Manager will function properly, but will not be able to use any of the debug facilities.
Recommended Action None
Error Message     
%QOS-QOS-7-ENS_ERROR ENS Debug:[chars] rc=[chars]
Explanation The ENS/NRS infrastructure is not available.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-7-ERR_BAG_REGISTER Failed to register bag structures with bag server (Reason: [chars])
Explanation The process could not register the data structures used by QoS statistics and management agents. This is not a critical error Qos will work properly. However show commands may not work.
Recommended Action None
Error Message     
%QOS-QOS-7-ERR_EVM_ASYNC_ATTACH Failed to attach handler for async events: [chars]
Explanation Failed to attach handler for async events.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-7-ERR_EVM_CREATE Failed to create event manager
Explanation Failed to create event manager.
Recommended Action None
Error Message     
%QOS-QOS-7-ERR_MEM_ALLOC [chars]
Explanation The QOS manager process could not get memory for the specified memory usage. This condition will occur if the system is low on memory.
Recommended Action None
Error Message     
%QOS-QOS-7-ERR_SYSDB SysDB error [chars]. Error code - [chars]
Explanation There were problems communicating with the SysDB. The reason and error message are displayed. If this message is displayed, the qosmgr process will restart itself.
Recommended Action None
Error Message     
%QOS-QOS-7-EVENT_CONN_ERR Error in [chars]: [chars]
Explanation Error encountered in opening connection to a required server. If this error occurs, the QoS Manager will restart itself.
Recommended Action None
Error Message     
%QOS-QOS-7-IM_CONNECT_FAIL Interface control server connection failed - [chars]. Error code - [chars]
Explanation Connection to interface manager failed. If this contition occurs, the QOS Manager will restart itself.
Recommended Action None
Error Message     
%QOS-QOS-7-OVL_RGST_FAIL Could not register ovl notification handler. Error code - [chars]
Explanation An error was encountered while trying to register the OVL notification handler.
Recommended Action None
Error Message     
%QOS-QOS-7-POLICY_INSTALL_FAIL Policy could not be installed [chars] [chars] Error code - [chars]
Explanation The specified policy could not be attached to an interface due to the specified reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-7-POLICY_NOT_FOUND Policy [chars] not found
Explanation The specified policy name was not found. Make sure that it is properly configured. If not please configure it.
Recommended Action Verify that the specified policy map is properly configured by issuing the following command show running policy-map .
Error Message     
%QOS-QOS-7-POLICY_REMOVE_FAIL Failed to remove policy [chars]. Error= [chars]
Explanation The specified policy could not be removed from an interface due to the specified reason.
Recommended Action Please follow the instructions from the error message.

	Cisco IOS XR System Error Reference Guide for Platform Independent Messages, Release 3.3
	Quality of Service (QOS) Messages
Cisco IOS XR System Error Reference Guide for Platform Independent Messages, Release 3.3 Preface Overview Access Control List (ACL) Messages Default Messages Diagnostic Messages Forwarding Information Base Messages High Availability (HA) Messages Installation Messages Internet Protocol (IP) Messages Layer 1 (L1) Messages Layer 2 (L2) Messages Media Messages Manageability (MGBL) Messages Operating System (OS) Messages Packet Infrastructure Messages Platform Messages Quality of Service (QOS) Messages Routing Messages Security Messages Service Messages Simple Network Management Protocol (SNMP ) Messages System Database Messages	Download this chapter Quality of Service (QOS) Messages Download the complete book Book-level PDF: Cisco IOS XR System Error Reference Guide for Platform Independent Messages (PDF - 7 MB) Feedback Table Of Contents Quality of Service (QoS) Messages CLASSIFY Messages FQ_QOS Messages MARK_QOS Messages QOS_CLASSIFY_NETIO Messages QOS_FIFO Messages QOS_RC_QOSMGR Messages QOS_TXM Messages QOS_WRED Messages QOS Messages Quality of Service (QoS) Messages This section contains all Quality of Service related System Error Messages. The following facility codes are represented in this module: •CLASSIFY Messages •FQ_QOS Messages •MARK_QOS Messages •QOS_CLASSIFY_NETIO Messages •QOS_FIFO Messages •QOS_RC_QOSMGR Messages •QOS_TXM Messages •QOS_WRED Messages •QOS Messages CLASSIFY Messages Error Message %QOS-CLASSIFY-4-MATCH_NOT_SUPPORTED Matching based on [chars] is not supported on [chars]. Explanation Matching based on the configured criterion is not supported in the specified direction. Reconfigure the policy map so that the specified match feature clause is removed and then reapply the service policy. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-CLASSIFY-4-TOO_MANY_CLASSES Policymap '[chars]' contains [dec] classmaps, which exceeds the maximum supported Explanation The number of class-maps configured for the specified policy exceeds the currently supported maximum. Currently, the maximum number of supported classes is 32. Recommended Action Reconfigure the policy map so that it contains fewer than 32 classes, and reapply the service policy. The total number of class-maps for a policy-map includes both the number of specifically configured class-maps as well as the number of class-maps configured for all of its child policies, plus the default class, if not already configured. Error Message %QOS-CLASSIFY-7-DEBUG_INIT_ERROR An error occurred during debug initialization, err: [chars] Explanation The QoS Classify DLL encountered an error during debug initialization. This is not a critical error. The QoS classification feature will function properly, but will not be able to use any of the debugging facilities. Recommended Action None FQ_QOS Messages Error Message %QOS-FQ_QOS-3-CAPS_ADD_FAIL Cannot add FQ capsulation to the data plane. Error code= [chars] Explanation QoS Manager failed to add capsulation for Fair Queueing to the the data plane. Recommended Action Turn on debugs with the following command debug qos control all dev and reapply the configuration command that caused the failure. Error Message %QOS-FQ_QOS-4-BUNDLE_BW_NOPCT Absolute bw specified for bundle interfaces, use percentage values instead Explanation Bandwidth for a bundle interfaces must be specified in percentage values instead of absolute values. Recommended Action Modify the bandwidth parameter to specify percentage instead of absolute values and then reapply the configuration. Error Message %QOS-FQ_QOS-4-BW_EXCEED Sum of allocated[chars] bandwidth exceeds the maximum Explanation The sum of the reserved bandwidth configured in the policy-map exceeds the maximum bandwidth for the interface. Recommended Action Correct the policymap so that the sum of reserved bandwidth is less than the maximum for the interface, and then reapply the service policy. Error Message %QOS-FQ_QOS-4-BW_REMAINING_PRIORITY_ERROR Remaining Bandwidth and Priority can not be configured under the same class Explanation Remaining Bandwidth and priority can not be configured under the same policy. Recommended Action Reconfigure the policy-map so that one of the features is removed and then reapply the service policy. Error Message %QOS-FQ_QOS-4-INVALID_UNIT An invalid or incompatible unit '[chars]' ([dec]) was specified for [chars]. Explanation An invalid unit has been specified for the feature mentioned in the message. Recommended Action Modify the configuration parameter so that the specified unit is compatible with the feature and platform. Error Message %QOS-FQ_QOS-4-MAX_CLASSES_EXCEEDED Number of classes exceeds the maximum number of classes allowed in a single policy map Explanation The number of class maps configured on the applied policy map exceeds the maximum allowed. Recommended Action Reconfigure the policy map so that the number of class-maps is reduced below the maximum allowed number and then reapply the policy. Error Message %QOS-FQ_QOS-4-MIN_BW_ERROR Configured minimum bandwidth ([dec] kbps) is greater than the configured shape bandwidth ([dec] kbps) for class '[chars]' Explanation The specified minimum bandwidth is greater than the shape bandwidth. Recommended Action Correct the configuration so that minimum bandwidth is less than the shape(maximum) bandwidth, and reapply the service policy. Error Message %QOS-FQ_QOS-4-NO_L1_BW_ERROR Level1 has no bandwidth guarantee. So cannot specify level2 bandwidth guarantee. Explanation A level 2 class has been configured with a bandwidth guarantee without the level 1 class having a bandwidth guarantee Recommended Action Reconfigure the policy-map so that the level 1 class includes a bandwidth guarantee and then reapply the service policy Error Message %QOS-FQ_QOS-4-SHAPE_BW_EXCEED Shape bandwidth exceeds 100 percent of the interface bandwidth Explanation The configured shaping bandwidth exceeds the maximum bandwidth for the interface. Recommended Action Correct the configuration so that shape bandwidth is less than or equal to the interface bandwidth. Error Message %QOS-FQ_QOS-4-VALUE_TOO_LARGE The value specified for [chars] is too large and cannot be handled by the system Explanation The configured value for the feature mentioned in the message is too large. Recommended Action Use a value which is less than 4294967295 kbps or KBytes (depending on the type of parameter configured). Error Message %QOS-FQ_QOS-5-PRIORITY_ERROR Shaping and Priority can not be configured under the same class Explanation Shape and priority can not be configured under the same class. Recommended Action Reconfigure the policy-map so that one of the features, either priority, or shaping is removed and then reapply the service policy. Error Message %QOS-FQ_QOS-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars] Explanation The QOS FQ dll encountered an error while initializing the debug facility. This is not a fatal error. QOS Fair Queueing will continue to execute properly, but will not be able to use the debugging facility. Recommended Action None Error Message %QOS-FQ_QOS-7-ERR_MEM_ALLOC Memory alloc error [chars] Explanation The router cannot allocate more memory while performing the specified task. This condition occurs only when the system is low on memory. Recommended Action None MARK_QOS Messages Error Message %QOS-MARK_QOS-5-NOT_SUPPORTED Marking of [chars] on egress interface not supported Explanation Marking of given attribute is not supported on the egress direction. Recommended Action Please modify the policy-map so that the specified marking option is not included in the policy-map configuration. Error Message %QOS-MARK_QOS-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars] Explanation The QOS Mark component encounterd an error while initializing the debug facility. This is not a fatal error. QOS Marking will continue to execute properly, but will not be able to use the debuging facility. Recommended Action None QOS_CLASSIFY_NETIO Messages Error Message %QOS-QOS_CLASSIFY_NETIO-7-DEBUG_INIT_ERROR A error occurred during debug initialization. Error: [chars] Explanation The QoS Classify DLL encountered an error while initializing the debug facility. This is not a fatal error. QoS Classify will continue to execute properly, but will not be able to use the debugging facility. Recommended Action None QOS_FIFO Messages Error Message %QOS-QOS_FIFO-7-DEBUG_INIT_ERROR An error occurred during debug initialization. Error: [chars] Explanation The QoS FIFO dll encountered a problem while initializingg the debug facility. This is not a fatal error. QoS FIFO will continue to execute properly, but will not be able to use the debugging facility. Recommended Action None Error Message %QOS-QOS_FIFO-7-DEBUG_INIT_ERROR An error occurred during debug initialization, err: [chars] Explanation The FIFO QoSMgr component encountered an error during debug initialization This is not a fatal condition. FIFO queueuing will work properly but will not be able to use any of the debugging facilities. Recommended Action None QOS_RC_QOSMGR Messages Error Message %QOS-QOS_RC_QOSMGR-4-INVALID_UNIT An invalid or incompatible unit '[chars]' ([dec]) was specified for [chars] Explanation An invalid unit has been specified for the feature mentioned in the message. Recommended Action Correct the policy-map so that a correct unit value is specified for the feature being configured Error Message %QOS-QOS_RC_QOSMGR-4-NOT_SUPPORTED Action [chars] not supported on [chars] Explanation The policy has an action that is not supported . Recommended Action Correct the policy-map to correct the action to a supported action. Error Message %QOS-QOS_RC_QOSMGR-4-RC_BUNDLE_BW_NOPCT Absolute bw specified for bundle interfaces, use percentage values instead Explanation For bundle interfaces, the bandwidth must be specified in percentage values of absolute values. Recommended Action Correct the policy-map so that the bandwidth value is specified as a percentage of the total bandwidth and then reapply the policy-map Error Message %QOS-QOS_RC_QOSMGR-4-RC_BW_EXCEED Policer rate exceeds 100 percent of the interface bandwidth Explanation The Policer rate in the policy-map exceeds the maximum bandwidth that the interface can support. Recommended Action Correct the policy-map so that the policer rate is smaller than the maximum of the interface it has been applied to. Error Message %QOS-QOS_RC_QOSMGR-4-VALUE_TOO_LARGE The value specified for [chars] is too large and cannot be handled by the system Explanation The value configured for the feature mentioned in the message is too large. Recommended Action Use a value which is less than 4294967295 kbps or KBytes (depending on the type of parameter configured). Error Message %QOS-QOS_RC_QOSMGR-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars] Explanation The QoSMgr policer component encountered an error during debug initialization This is not a fatal condition. Policing will work properly but will not be able to use any of the debugging facilities. Recommended Action None QOS_TXM Messages Error Message %QOS-QOS_TXM-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars] Explanation The QOS Mark process encounterd an error while initializing the debug facility. This is not a fatal error. QOS Marking will continue to execute properly, but will not be able to use the debuging facility. Recommended Action None Error Message %QOS-QOS_TXM-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars] Explanation The QOS TXM process encountered an error while initializing the debug facility. This is not a fatal error. QOS TXM will continue to execute properly, but will not be able to use the debugging facility. Recommended Action None Error Message %QOS-QOS_TXM-7-UNINITIALISE_ERROR An error occurred in initialization sequence for iface: [chars] Explanation The QOS TXM process encountered an error in its initialsation sequence. This is a serious error. QOS TXM functioning correctly is not guranteed depending upon the exact problem in initialisation sequence Recommended Action None QOS_WRED Messages Error Message %QOS-QOS_WRED-7-DEBUG_INIT_ERROR An error occurred during debug initialization. Error: [chars] Explanation The QoS WRED dll encountered a problem while initializing the debug facility. This is not a fatal error. QoS WRED will continue to execute properly, but will not be able to use the debugging facility. Recommended Action None Error Message %QOS-QOS_WRED-7-INVALID_WRED_TYPE The type of random-detect configured under class '[chars]' is invalid or not supported on this platform. Please configure a supported random-detect type. Explanation An invalid type of random-detect was configured for the class specified in the message. Recommended Action Please reconfigure the policy-map with a supported type of random-detect. If the configured type of random-detect is supported on this platform and this message is seen, please contact the customer support with the following information. QOS Messages Error Message %QOS-QOS-3-DLL_INIT_FAIL Could not initialize [chars] dll. Error code - [chars] Explanation An error was encountered while trying to initialize a DLL that supports a given feature. Both the DLL name and the error code are displayed. This is a critical error in the QOS component. It indicates that the DLL that implements a feature does not provide an initializing function. This indicates that some QOS feature is not working properly. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-FEATURE_ADD_FAIL Failed to add policy [chars], class = [chars], feature = [chars]. Explanation Failed to add the specified feature while applying the specified service policy. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-FILE_ERROR File [chars] error: [chars]. Reason: [chars] Explanation An error was encountered while accessing a file. Both the file name and the error reason are displayed. This is a critical error in the QOS component. It indicates that the file that defines a feature is missing from the system and the related QOS feature will not work properly. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-FILE_WRONG_INFO File [chars] [chars] [dec] Explanation An error was encountered while accessing a file. Both the file name and the error reason are displayed. This is a critical error in the QOS component. It indicates that the file that defines a feature is missing from the system and the related QOS feature will not working properly. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-FT_REMOVE_FAIL Failed to remove the feature [chars]. Error code - [chars] Explanation The QOS Manager process failed to remove the specified feature. The error code is also displayed. Recommended Action Please turn on debugs using the following command: debug qos control all dev and reenter the configuration command that caused the error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-FT_SEND_FAIL Sending control to [chars] feature failed Explanation Failed to send a control feature information to the Execution Agent. The name of the feature is displayed. Recommended Action Please turn on debugs using the following command: debug qos control all dev and reenter the configuration command that caused the error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-MGR_DLL_OPEN_FAIL Could not open [chars] DLL. Error code - [chars] Explanation An error was encountered while trying to open a DLL that supports a given feature. Both the DLL name and the error code are displayed. This is a critical error in the QOS component. It indicates that the DLL that implements the feature is not present in the system. This indicates that some QOS feature is not working properly. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-MSG_SEND_FAIL Failed to send message to feature [chars] [chars]. Error code - [chars] Explanation Failed to send the a message to the specified feature due to the error message displayed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-4-NODE_INSTL_FAIL Could not install [chars] feature [chars] Explanation An error was encountered while trying to add the specified feature node to NetIO. Both the feature name and the error code are displayed. This is a critical error in the QOS component. It indicates that some QOS feature is not working properly. Recommended Action Please provide the output of the commands: Please provide the output of the commands: show running configuration show qos trace Error Message %QOS-QOS-6-FT_CONFIGURE_FAIL Failed to configure feature [chars]. Error code - [chars] Explanation The specified feature could not be configured due to the specified reason. Recommended Action None Error Message %QOS-QOS-6-HPOLICY_ATTACH_FAIL Too many levels of hierarchy in policy [chars]. Explanation The Policy could not be installed because it has more than 2 levels of hierarchy. Recommended Action Simplify the policy-map to include no more than 2 levels of hierarchy. and reapply it. Error Message %QOS-QOS-6-POLICY_ATTACH_FAIL Service policy [chars] could not be attached to [chars]. Error code - [chars] Explanation Policy could not be installed. The reason is displayed. Recommended Action Please verify that the specified policy has been configured with the following command: show running configuration Error Message %QOS-QOS-7-CLASSMAP_NOT_FOUND Class map [chars] not found Explanation The specified class map was not found. Make sure that it is properly configured. If not, please confifure it. Recommended Action Verify that the specified class-map name is properly configured by issuing the following command show running class-map Error Message %QOS-QOS-7-DLL_REGISTER_CERR_FAIL Could not register error codes for [chars] dll. Error code - [chars] Explanation Could not get register DLL error codes. This is not a critical error. The QOS Manager will function properly, but will not be able to use any of the debug facilities. Recommended Action None Error Message %QOS-QOS-7-ENS_ERROR ENS Debug:[chars] rc=[chars] Explanation The ENS/NRS infrastructure is not available. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-7-ERR_BAG_REGISTER Failed to register bag structures with bag server (Reason: [chars]) Explanation The process could not register the data structures used by QoS statistics and management agents. This is not a critical error Qos will work properly. However show commands may not work. Recommended Action None Error Message %QOS-QOS-7-ERR_EVM_ASYNC_ATTACH Failed to attach handler for async events: [chars] Explanation Failed to attach handler for async events. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-7-ERR_EVM_CREATE Failed to create event manager Explanation Failed to create event manager. Recommended Action None Error Message %QOS-QOS-7-ERR_MEM_ALLOC [chars] Explanation The QOS manager process could not get memory for the specified memory usage. This condition will occur if the system is low on memory. Recommended Action None Error Message %QOS-QOS-7-ERR_SYSDB SysDB error [chars]. Error code - [chars] Explanation There were problems communicating with the SysDB. The reason and error message are displayed. If this message is displayed, the qosmgr process will restart itself. Recommended Action None Error Message %QOS-QOS-7-EVENT_CONN_ERR Error in [chars]: [chars] Explanation Error encountered in opening connection to a required server. If this error occurs, the QoS Manager will restart itself. Recommended Action None Error Message %QOS-QOS-7-IM_CONNECT_FAIL Interface control server connection failed - [chars]. Error code - [chars] Explanation Connection to interface manager failed. If this contition occurs, the QOS Manager will restart itself. Recommended Action None Error Message %QOS-QOS-7-OVL_RGST_FAIL Could not register ovl notification handler. Error code - [chars] Explanation An error was encountered while trying to register the OVL notification handler. Recommended Action None Error Message %QOS-QOS-7-POLICY_INSTALL_FAIL Policy could not be installed [chars] [chars] Error code - [chars] Explanation The specified policy could not be attached to an interface due to the specified reason. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-7-POLICY_NOT_FOUND Policy [chars] not found Explanation The specified policy name was not found. Make sure that it is properly configured. If not please configure it. Recommended Action Verify that the specified policy map is properly configured by issuing the following command show running policy-map . Error Message %QOS-QOS-7-POLICY_REMOVE_FAIL Failed to remove policy [chars]. Error= [chars] Explanation The specified policy could not be removed from an interface due to the specified reason. Recommended Action Please follow the instructions from the error message.
	Terms & Conditions \| Privacy Statement \| Cookie Policy \| Trademarks