Table Of Contents

Troubleshooting Analog and Digital Voice Port Configurations

Troubleshooting Chart

Troubleshooting Analog and Digital Voice Port Configurations

---

This chapter provides information to assist you in analyzing and troubleshooting voice port problems.

Troubleshooting Chart

Table 1 lists some problems that you might encounter after configuring voice ports. It also provides some suggested remedies.

Table 1 Troubleshooting Voice Port Configurations 

Problem	Suggested Action
No connectivity	Ping the associated IP address to confirm connectivity. If you cannot successfully ping your destination, refer to the Cisco IOS IP Configuration Guide.
No connectivity	Enter the show controller t1 or show controller e1 command with the controller number for the voice port you are troubleshooting. This will tell you: •If the controller is up. If it is not, use the no shutdown command to make it active. •Whether alarms have been reported. •What parameter values have been set for the controller (framing, clock source, line code, cable length). If these values do not match those of the telephony connection you are making, reconfigure the controller. See the "show controller Command: Examples" section in the Verifying Analog and Digital Voice-Port Configurations chapter for output.
No connectivity	Enter the show voice port command with the voice port number that you are troubleshooting, which will tell you: •If the voice port is up. If it is not, use the no shutdown command to make it active. •What parameter values have been set for the voice port, including default values (these do not appear in the output for the show running-config command). If these values do not match those of the telephony connection you are making, reconfigure the voice port. See the "show voice port Command: Examples" section in the Verifying Analog and Digital Voice-Port Configurations chapter for sample output.
Telephony device buzzes or does not ring	Use the show voice port command to confirm that the ring frequency command is configured correctly. It must match the connected telephony equipment and may be country-dependent.
Distorted speech	Use the show voice port command to confirm the cptone keyword setting (also called region tone) is US. Setting a wrong cptone could result in faulty voice reproduction during analog-to-digital or digital-to-analog conversions.
Music on hold is not heard	Reduce the configured level for the music-threshold command.
Background noise is not heard	Enable the comfort-noise command.
Long pauses occur in conversation; like speaking on a walkie-talkie	Overall delay is probably excessive; the standard for adequate voice quality is 150 milliseconds (ms) one-way transit delay. Measure delay by using ping tests at various times of the day with different network traffic loads. If delay must be reduced, areas to examine include propagation delay of signals between the sending and receiving endpoints, voice encoding delay, and the voice packetization time for various VoIP codecs.
Jerky or choppy speech	Variable delay, or jitter, is being introduced by congestion in the packet network. Two possible remedies are to: •Reduce the amount of congestion in your packet network. Pings between VoIP endpoints will give an idea of the round-trip delay of a link, which should never exceed 300 ms. Network queuing and dropped packets should also be examined. •Increase the size of the jitter buffer with the playout-delay command. (Refer to the Cisco IOS Voice Troubleshooting and Monitoring Guide.)
Clipped or fuzzy speech	•Reduce input gain. (Refer to the Cisco IOS Voice Troubleshooting and Monitoring Guide.) •Change the voice activity detection (VAD) level. Sometimes VAD cuts the sound too early and the speaker's voice is clipped. You can also change the time that VAD waits for silence.
Clipped speech	Reduce the input level at the listener's router. (Refer to the Cisco IOS Voice Troubleshooting and Monitoring Guide.)
Volume too low or missed Dual-Tone Multifrequency (DTMF)	Increase speaker's output level or listener's input level. (Refer to the Cisco IOS Voice Troubleshooting and Monitoring Guide.)
Echo interval is greater than 25 ms (sounds like a separate voice)	Configure the echo-cancel enable command and increase the value for the echo-cancel coverage keyword. (See the "Configuring Echo Cancellation" section on page 75.)
Too much echo	Reduce the output level at the speaker's voice port. (Refer to the Cisco IOS Voice Troubleshooting and Monitoring Guide.)

---

Note For information on test commands that force voice ports into specific states for testing refer to the Cisco IOS Voice Troubleshooting and Monitoring Guide.

---

CCDE, CCENT, CCSI, Cisco Eos, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco Nurse Connect, Cisco Pulse, Cisco StackPower, Cisco StadiumVision, Cisco TelePresence, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels, Flip for Good, Flip Mino, Flipshare (Design), Flip Ultra, Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn, Cisco Capital, Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store, and Flip Gift Card are service marks; and Access Registrar, Aironet, AllTouch, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco  IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, Continuum, EtherFast, EtherSwitch, Event Center, Explorer, Fast Step, Follow Me Browsing, FormShare, GainMaker, GigaDrive, HomeLink, iLYNX, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, Laser Link, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerKEY, PowerPanels, PowerTV, PowerTV (Design), PowerVu, Prisma, ProConnect, ROSA, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0908R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

© 2009 Cisco Systems, Inc. All rights reserved.