Cisco IOS Security Configuration Guide: Secure Connectivity, Release 12.4 - Stateful Failover for IPsec [Cisco IOS Software Releases 12.4 Mainline]

Table Of Contents

Stateful Failover for IPsec

Finding Feature Information

Contents

Prerequisites for Stateful Failover for IPsec

Restrictions for Stateful Failover for IPsec

Information About Stateful Failover for IPsec

Supported Deployment Scenarios: Stateful Failover for IPsec

IPsec Stateful Failover for Remote Access Connections

Dead Peer Detection with IPsec High Availability

How to Use Stateful Failover for IPsec

Enabling HSRP: IP Redundancy and a Virtual IP Address

Prerequisites for Spanning Tree Protocol and HSRP Stability

Restrictions

Troubleshooting Tips

Examples

What to Do Next

Enabling SSO

SSO: Interacting with IPsec and IKE

Prerequisites

Troubleshooting Tips

Examples

What to Do Next

Configuring Reverse Route Injection on a Crypto Map

Configuring RRI on Dynamic Crypto Map

Configuring RRI on a Static Crypto Map

Examples

What to Do Next

Enabling Stateful Failover for IKE and IPsec

Enabling Stateful Failover for IKE

Enabling Stateful Failover for IPsec

Enabling Stateful Failover for Tunnel Protection

What to Do Next

Protecting SSO Traffic

Examples

Managing and Verifying High Availability Information

Managing Anti-Replay Intervals

Examples

Managing and Verifying HA Configurations

Examples

Configuration Examples for Stateful Failover

Configuring IPsec Stateful Failover: Example

Configuring IPsec Stateful Failover for an Easy VPN Server: Example

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Feature Information for Stateful Failover for IPsec

Stateful Failover for IPsec

First Published: September 20, 2004

Last Updated: March 28, 2011

Stateful failover for IP Security (IPsec) enables a router to continue processing and forwarding IPsec packets after a planned or unplanned outage occurs. Customers employ a backup (secondary) router that automatically takes over the tasks of the active (primary) router if the active router loses connectivity for any reason. This process is transparent to the user and does not require adjustment or reconfiguration of any remote peer.

Stateful failover for IPsec is designed to work in conjunction with stateful switchover (SSO) and Hot Standby Routing Protocol (HSRP). HSRP provides network redundancy for IP networks, ensuring that user traffic immediately and transparently recovers from failures in network edge devices or access circuits. That is, HSRP monitors both the inside and outside interfaces so that if either interface goes down, the whole router is deemed to be down and ownership of Internet Key Exchange (IKE) and IPsec security associations (SAs) is passed to the standby router (which transitions to the HSRP active state). SSO allows the active and standby routers to share IKE and IPsec state information so that each router has enough information to become the active router at any time. To configure stateful failover for IPsec, a network administrator should enable HSRP, assign a virtual IP address, and enable the SSO protocol.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for Stateful Failover for IPsec" section.

Use Cisco Feature Navigator to find information about platform support and Cisco IOS and Catalyst OS software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

•Prerequisites for Stateful Failover for IPSec, page 2

•Restrictions for Stateful Failover for IPSec, page 2

•Information About Stateful Failover for IPSec, page 3

•How to Use Stateful Failover for IPSec, page 6

•Configuration Examples for Stateful Failover, page 27

•Additional References, page 36

•Feature Information for Stateful Failover for IPsec

Prerequisites for Stateful Failover for IPsec

Complete, Duplicate IPsec and IKE Configuration on the Active and Standby Devices

This document assumes that you have a complete IKE and IPsec configuration. (This document describes only how to add stateful failover to a working IPsec configuration.)

The IKE and IPsec configuration that is set up on the active device must be duplicated on the standby device. That is, the crypto configuration must be identical with respect to Internet Security Association and Key Management Protocol (ISAKMP) policy, ISAKMP keys (preshared), IPsec profiles, IPsec transform sets, all crypto map sets that are used for stateful failover, all access control lists (ACLs) that are used in match address statements on the crypto map sets, all AAA configurations used for crypto, client configuration groups, ip local pools used for crypto, and ISAKMP profiles.

Note None of the configuration information between the active and standby device is automatically transferred; the user is responsible for ensuring that the crypto configurations match on both devices. If the crypto configurations on both devices do not match, failover from the active device to the standby device will not be successful.

Device Requirements

•Stateful failover for IPsec requires that your network contains two identical routers that are available to be either the primary or secondary device. Both routers should be the same type of device, have the same CPU and memory, and have either no encryption accelerator or identical encryption accelerators.

•This feature is currently supported only on a limited number of platforms. To check the latest platform support, go to Cisco Feature Navigator at http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp.

Restrictions for Stateful Failover for IPsec

When configuring redundancy for a virtual private network (VPN), the following restrictions exist:

•Both the active and standby devices must run the identical version of the Cisco IOS software, and both the active and standby devices must be connected via hub or switch.

•The Cisco Integrated Services Routers (ISRs) and the VPN modules that support stateful failover for IPsec are as follows:

–The AIM-VPN/BPII-PLUS and AIM-VPN/SSL-1 hardware encryption modules are supported in a Cisco 1841 router.

–The AIM-VPN/EPII-Plus and AIM-VPN/SSL-2 hardware encryption modules are supported in Cisco 2801, 2811, 2821 and 2851 routers.

–The AIM-VPN/EPII+ and AIM-VPN/SSL-3 hardware encryption modules are supported in a Cisco 3825 router.

–The AIM-VPN/HPII+ and AIM-VPN/SSL3 hardware encryption modules are supported in a Cisco 3845 router.

–The VPN Acceleration Module (VAM) and VAM2 hardware encryption modules are supported in a Cisco 7200 series router.

•Only "box-to-box" failover is supported; that is, intrachassis failover is currently not supported.

•WAN interfaces between the active (primary) router and the standby (secondary) router are not supported. (HSRP requires inside interfaces and outside interfaces to be connected via LANs.)

•Load balancing is not supported; that is, no more than one device in a redundancy group can be active at any given time.

•Stateful failover of IPsec with Layer 2 Tunneling Protocol (L2TP) is not supported.

•Public key infrastructure (PKI) is not supported when used with stateful failover. (Only preshared keys for IKE are supported.)

•IKE keepalives are not supported. (Enabling this functionality will cause the connection to be torn down after the standby router assumes ownership control.) However, dead peer detection (DPD) and periodic DPD are supported.

•IPsec idle timers are not supported when used with stateful failover.

•A stateful failover crypto map applied to an interface in a virtual route forwarding (VRF) instance is not supported. However, VRF-aware IPsec features are supported when a stateful failover crypto map is applied to an interface in the global VRF.

•Stateful failover is not compatible or interoperable with the State Synchronization Protocol (SSP) version of stateful failover (which is available in Cisco IOS Release 12.2YX1 and Cisco IOS Release 12.2SU).

Information About Stateful Failover for IPsec

To configure stateful failover for VPNs, you should understand the following concepts:

•Supported Deployment Scenarios: Stateful Failover for IPsec, page 3

•IPSec Stateful Failover for Remote Access Connections, page 5

•Dead Peer Detection with IPsec High Availability

Supported Deployment Scenarios: Stateful Failover for IPsec

It is recommended that you implement IPsec stateful failover in one of the following recommended deployment scenarios—a single interface scenario or a dual interface scenario.

In a single interface scenario, the VPN gateways use one LAN connection for both encrypted traffic arriving from remote peers and decrypted traffic flowing to inside hosts (see Figure 1). The single interface design allows customers to save money on router ports and subnets. This design is typically used if all traffic flowing in and out of the organization does not traverse the VPN routers.

Figure 1 Single Interface Network Topology

In a dual interface scenario, a VPN gateway has more than one interface, enabling traffic to flow in and out of the router via separate interfaces (see Figure 2). This scenario is typically used if traffic flowing in and out of a site must traverse the routers, so the VPN routers will provide the default route out of the network.

Figure 2 Dual Interface Network Topology

Table 1 lists the functionality available in both a single interface scenario and a dual interfaces scenario.

Table 1 IPsec StateFul Failover: Single and Dual Interface Functionality Overview

Single Interface

Dual Interface

Route Injection

Routes must be injected to provide the devices that are behind the VPN gateways with a next hop for traffic that requires encryption. Stateful failover for IPsec typically requires routes to be injected for this network topology.

If the VPN gateways are not the logical next hop for devices inside the network, the routes must be created and injected into the routing process. Thus, traffic that is returning from inside the network can be sent back to the VPN routers for IPsec services before it is sent out. A virtual IP (VIP) address cannot be used as the advertiser of routing updates, so flows must be synchronized via the injected routes.

If the VPN gateways are the next hop (default route) for all devices inside the network, the VIP address that is used on the inside interfaces can be used as the next hop. Thus, injection of the VPN routes is not required. However, static routes on inside hosts must be used to direct the routes to the next hop VIP address.

HSRP Configuration

The role of HSRP is simplified in a single interface design because if the only interface is disabled, the entire device is deemed unavailable. This functionality helps to avoid some of the routing considerations to be discussed in the next scenario.

Because each interface pair functions independently, you should configure HSRP so that multiple pairs of interfaces can be tracked. (That is, HSRP should not be configured on only one pair of interfaces or on both pairs of interfaces without each pair mutually tracking each other.) Mutual tracking means that if the outside interface does fail, the inside interface on the same router will also be deemed down, allowing for complete router failover to the secondary router.

Secure State Information

If secured-state information is passed between routers, the information is passed over the same interface as all other traffic.

The router has a separate inside and outside interface; thus, the inside interface can be used as a more secure channel for the exchange of state information.

Firewall Configuration

The VPN gateways can sit in front of the firewall or behind the firewall.

VPN gateways may sit behind or in front of a firewall, a firewall can be installed in parallel to the VPN gateways.

IPsec Stateful Failover for Remote Access Connections

The main difference between a remote access and a LAN-to-LAN connection is the use of Xauth and mode-config. IKE Xauth is often used to authenticate the user. IKE mode-config is often used to push security policy from the hub (concentrator) router to the user's IPsec implementation. Mode-config is also typically used to assign an internal company network IP address to a user.

In addition to the differences between a remote access configuration and a LAN-to-LAN configuration, you should note the following remote-access-server-specific functions:

•Assigned IP address—The IP address can be assigned to the client via one of the following options:

–Local IP pools. For local IP pools, the administrator must first configure identical local IP address pools on each router in the high availability (HA) pair (via the ip local pool client-address-pool command). This pool name can be applied in one of two places—in a group policy via the crypto isakmp client configuration group group-name (and the submode command pool pool-name) or in a client configuration via the crypto isakmp client configuration address-pool local local-pool command.

–RADIUS-assigned address. If you are using RADIUS authentication and the RADIUS server returns the Framed-IP-Address attribute, the concentrator will always assign that address to the client. It is recommended that you refer to your RADIUS server vendor's documentation, especially for vendors that allow you to configure address pools on the RADIUS server. Typically those servers require crypto accounting to work properly.

To enable accounting on the HA pair, you should issue the following commands on both Active and Standby devices: aaa accounting network radius-accounting start-stop group radius then apply radius-accounting either to the crypto isakmp profile or the crypto map set.

•RADIUS NAS-IP address—The HA pair should appear as a single device to the RADIUS server. Thus, both HA routers must communicate with the RADIUS server using the same IP address. However, when communicating with the RADIUS server, the router must use a physical IP address, not a virtual IP (VIP) address as the NAS-IP address of the router. To configure the RADIUS NAS-IP address for the HA pair, you must configure the same loopback address in the HA pair via interface loopback ip address command; thereafter, you must issue the ip radius source-interface loopback command in the HA pair. Finally, add the new loopback IP address to the RADIUS servers configuration so the RADIUS server can process requests from the HA pair.

For additional information on how to configure IPsec stateful failover for a remote access connection, see the section "Configuring IPSec Stateful Failover for an Easy VPN Server: Example" in this document.

Dead Peer Detection with IPsec High Availability

To configure Dead Peer Detection (DPD) with IPsec High Availability (HA), it is recommended that you use a value other than the default (2 seconds). A keepalive time of 10 seconds with 5 retries seems to work well with HA because of the time it takes for the router to get into active mode.

To configure DPD with IPsec HA, use the crypto isakmp keepalive command.

How to Use Stateful Failover for IPsec

This section contains the following procedures:

•Enabling HSRP: IP Redundancy and a Virtual IP Address, page 6 (required)

•Enabling SSO, page 9 (required)

•Configuring Reverse Route Injection on a Crypto Map, page 13 (required)

•Enabling Stateful Failover for IKE and IPSec, page 15 (required)

•Protecting SSO Traffic, page 18 (optional)

•Managing and Verifying High Availability Information, page 20 (optional)

Enabling HSRP: IP Redundancy and a Virtual IP Address

HSRP provides two services—IP redundancy and a VIP address. Each HSRP group may provide either or both of these services. IPsec stateful failover uses the IP redundancy services from only one HSRP standby group. It can use the VIP address from one or more HSRP groups. Use the following task to configure HSRP on the outside and inside interfaces of the router.

Note Perform this task on both routers (active and standby) and of both interfaces on each router.

Note You must perform at least one of the prerequisite steps for correct HSRP operation.

Note Each time an active device relinquishes control to become the standby device, the active device will reload. This functionality ensures that the state of the new standby device synchronizes correctly with the new active device.

Prerequisites for Spanning Tree Protocol and HSRP Stability

If a switch connects the active and standby routers, you must perform one of the following steps to ensure that the correct settings are configured on that switch:

•Enable the spanning-tree portfast command on every switch port that connects to a HSRP-enabled router interface.

•Disable the Spanning Tree Protocol (STP) on the switch only if your switch does not connect to other switches. Disabling spanning tree in a multi-switch environment may cause network instability.

•Enable the standby delay minimum [min-delay] reload [reload-delay] command if you do not have access to the switch. The reload-delay argument should be set to a value of at least 120 seconds. This command must be applied to all HSRP interfaces on both routers.

For more information on HSRP instability, see the Avoiding HSRP Instability in a Switching Environment with Various Router Platforms technical note.

Restrictions

•Both the inside (private) interface and the outside (public) interface must belong to separate HSRP groups, but the HSRP group number can be the same.

•The state of the inside interface and the outside interface must be the same—both interfaces must be in the active state or standby state; otherwise, the packets will not have a route out of the private network.

•Standby priorities should be equal on both active and standby routers. If the priorities are not equal, the higher priority router will unnecessarily take over as the active router, negatively affecting uptime.

•The IP addresses on the HSRP-tracked interfaces of the standby and active routers should both be either lower or higher on one router than the other. In the case of equal priorities (an HA requirement), HSRP will assign the active state on the basis of the IP address. If an addressing scheme exists so that the public IP address of Router A is lower than the public IP address of Router B, but the opposite is true for their private interfaces, an active/standby-standby/active split condition could exist which will break connectivity.

SUMMARY STEPS

1. enable

2. configure terminal

3. interface type number

4. standby standby-group-number name standby-group-name

5. standby standby-group-number ip ip-address

6. standby standby-group-number track interface-name

7. standby [group-number] preempt

8. standby [group-number] timers [msec] hellotime [msec] holdtime

9. standby delay minimum [min-delay] reload [reload-delay]

10. Repeat.

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

interface type number
Example:

Router(config)# interface Ethernet 0/0

Configures an interface type for the router and enters interface configuration mode.

Step 4

standby standby-group-number name standby-group-name
Example:

Router(config-if)# standby 1 name HA-out

Assigns a user-defined group name to the HSRP redundancy group.

Note The standby-group-number argument should be the same for both routers that are on directly connected interfaces. However, the standby-group-name argument should be different between two (or more) groups on the same router.

The standby-group-number argument can be the same on the other pair of interfaces as well.

Step 5

standby standby-group-number ip ip-address
Example:

Router(config-if)# standby 1 ip 209.165.201.1

Assigns an IP address that is to be "shared" among the members of the HSRP group and owned by the primary IP address.

Note The virtual IP address must be configured identically on both routers (active and standby) that are on directly connected interfaces.

Step 6

standby standby-group-number track interface-name
Example:

Router(config-if)# standby 1 track Ethernet1/0

Configures HSRP to monitor the second interface so that if either of the two interfaces goes down, HSRP causes failover to the standby device.

Note Although this command is not required, it is recommended for dual interface configurations.

Step 7

standby [group-number] preempt
Example:

Router(config-if)# standby 1 preempt

Enables the active device to relinquish control because of an interface tracking event.

Step 8

standby [group-number] timers [msec] hellotime [msec] holdtime
Example:

Router(config-if)# standby 1 timers 1 5

(Optional) Configures the time between hello packets and the time before other routers declare the active Hot Standby or standby router to be down.

•holdtime—Amount of time the routers take to detect types of failure. A larger hold time means that failure detection will take longer.

For the best stability, it is recommended that you set the hold time between 5 and 10 times the hello interval time; otherwise, a failover could falsely occur when no actual failure has happened.

Step 9

standby delay minimum [min-delay] reload [reload-delay]
Example:

Router(config-if)# standby delay minimum reload 120

Configures the delay period before the initialization of HSRP groups.

Note It is suggested that you enter 120 as the value for the reload-delay argument and leave the min-delay argument at the preconfigured default value.

Step 10

Repeat.

Repeat this task on both routers (active and standby) and on both interfaces of each router.

Troubleshooting Tips

To help troubleshoot possible HSRP-related configuration problems, issue any of the following HSRP-related debug commands—debug standby errors, debug standby events, and debug standby packets [terse].

Examples

The following example shows how to configure HSRP on a router:
interface Ethernet0/0
 ip address 209.165.201.1 255.255.255.224
 standby 1 ip 209.165.201.3
 standby 1 preempt
 standby 1 name HA-out
 standby 1 track Ethernet1/0
 standby delay reload 120
What to Do Next

After you have successfully configured HSRP on both the inside and outside interfaces, you should enable SSO as described the in the section "Enabling SSO" section."

Enabling SSO

Use this task to enable SSO, which is used to transfer IKE and IPsec state information between two routers.

SSO: Interacting with IPsec and IKE

SSO is a method of providing redundancy and synchronization for many Cisco IOS applications and features. SSO is necessary for IPsec and IKE to learn about the redundancy state of the network and to synchronize their internal application state with their redundant peers.

Prerequisites

•You should configure HSRP before enabling SSO.

•To avoid losing SCTP communication between peers, be sure to include the following commands to the local address section of the SCTP section of the IPC configuration:

–retransmit-timeout retran-min [msec] retra-max [msec]

–path-retransmit max-path-retries

–assoc-retransmit retries

SUMMARY STEPS

1. enable

2. configure terminal

3. redundancy inter-device

4. scheme standby standby-group-name

5. exit

6. ipc zone default

7. association 1

8. protocol sctp

9. local-port local-port-number

10. local-ip device-real-ip-address [device-real-ip-address2]

11. retransmit-timeout retran-min [msec] retra-max [msec]

12. path-retransmit max-path-retries

13. assoc-retransmit retries

14. exit

15. remote-port remote-port-number

16. remote-ip peer-real-ip-address [peer-real-ip-address2]

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

redundancy inter-device
Example:

Router(config)# redundancy inter-device

Configures redundancy and enters inter-device configuration mode.

To exit inter-device configuration mode, use the exit command. To remove all inter-device configuration, use the no form of the command.

Step 4

scheme standby standby-group-name
Example:

Router(config-red-interdevice)# scheme standby HA-out

Defines the redundancy scheme that is to be used. Currently, "standby" is the only supported scheme.

•standby-group-name—Must match the standby name specified in the standby name interface configuration command. Also, the standby name should be the same on both routers.

Note Only the active or standby state of the standby group is used for SSO. The VIP address of the standby group is not required or used by SSO. Also, the standby group does not have to be part of any crypto map configuration.

Step 5

exit
Example:

Router(config-red-interdevice)# exit

Exits inter-device configuration mode.

Step 6

ipc zone default
Example:

Router(config)# ipc zone default

Configures the inter-device communication protocol, Inter-Process Communication (IPC), and enters IPC zone configuration mode.

Use this command to initiate the communication link between the active router and standby router.

Step 7

association 1
Example:

Router(config-ipczone)# association 1

Configures an association between the two devices and enters IPC association configuration mode.

Step 8

protocol sctp
Example:

Router(config-ipczone-assoc)# protocol sctp

Configures Stream Control Transmission Protocol (SCTP) as the transport protocol and enters SCTP protocol configuration mode.

Step 9

local-port local-port-number
Example:

Router(config-ipc-protocol-sctp)# local-port 5000

Defines the local SCTP port number that is used to communicate with the redundant peer and puts you in IPC transport - SCTP local configuration mode.

•local-port-number—There is not a default value. This argument must be configured for the local port to enable inter-device redundancy. Valid port values: 1 to 65535.

The local port number should be the same as the remote port number on the peer router.

Step 10

local-ip device-real-ip-address [device-real-ip-address2]
Example:

Router(config-ipc-local-sctp)# local-ip 10.0.0.1

Defines at least one local IP address that is used to communicate with the redundant peer.

The local IP addresses must match the remote IP addresses on the peer router. There can be either one or two IP addresses, which must be in the global VRF. A virtual IP address cannot be used.

Step 11

retransmit-timeout retran-min [msec] retra-max [msec]
Example:

Router(config-ipc-local-sctp)# retransmit-timeout 300 10000

Configures the maximum amount of time, in milliseconds, that SCTP will wait before retransmitting data.

•retran-min: 300 to 60000; default: 300

•retran-max: 300 to 60000; default: 600

Step 12

path-retransmit max-path-retries
Example:

Router(config-ipc-local-sctp)# path-retransmit 10

Configures the number of consecutive retransmissions SCTP will perform before failing a path within an association.

•max-path-retries: 2 to 10; default: 4 retries

Step 13

assoc-retransmit retries
Example:

Router(config-ipc-local-sctp)# assoc-retransmit 10

Configures the number of consecutive retransmissions SCTP will perform before failing an association.

•max-association-retries: 2 to 10; default: 4 retries

Step 14

exit
Example:

Router(config-ipc-local-sctp)# exit

Exits IPC transport - SCTP local configuration mode.

Step 15

remote-port remote-port-number
Example:

Router(config-ipc-protocol-sctp)# remote-port 5000

Defines the remote SCTP port number that is used to communicate with the redundant peer and puts you in IPC transport - SCTP remote configuration mode.

Note remote-port-number—There is not a default value. This argument must be configured for the remote port to enable inter-device redundancy. Valid port values: 1 to 65535.

The remote port number should be the same as the local port number on the peer router.

Step 16

remote-ip peer-real-ip-address [peer-real-ip-address2]
Example:

Router(config-ipc-remote-sctp)# remote-ip 10.0.0.2

Defines at least one remote IP address of the redundant peer that is used to communicate with the local device.

All remote IP addresses must refer to the same device.

A virtual IP address cannot be used.

Troubleshooting Tips

To help troubleshoot possible SSO-related configuration problems, issue the debug redundancy command.

Examples

The following example shows how to enable SSO:
!
redundancy inter-device
 scheme standby HA-out
!
!
ipc zone default
 association 1
  no shutdown
  protocol sctp
   local-port 5000
    local-ip 10.0.0.1
    retransmit-timeout 300 10000
    path-retransmit 10
    assoc-retransmit 10
   remote-port 5000
    remote-ip 10.0.0.2
!
What to Do Next

After you have enabled SSO, you should configure reverse route injection (RRI) on a crypto map as shown in the following section.

Configuring Reverse Route Injection on a Crypto Map

You should configure RRI on all existing crypto maps that you want to use with stateful failover. RRI is used with stateful failover so routers on the inside network can learn about the correct path to the current active device. When failover occurs, the new active device injects the RRI routes into its IP routing table and sends out routing updates to its routing peers.

Use one of the following tasks to configure RRI on a dynamic or static crypto map.

•Configuring RRI on Dynamic Crypto Map, page 13

•Configuring RRI on a Static Crypto Map, page 14

Configuring RRI on Dynamic Crypto Map

Dynamic crypto map entries, like regular static crypto map entries, are grouped into sets. A set is a group of dynamic crypto map entries all with the same dynamic map name but each with a different dynamic sequence number. Each member of the set may be configured for RRI.

SUMMARY STEPS

1. enable

2. configure terminal

3. crypto dynamic-map map-name seq-num

4. reverse-route

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

crypto dynamic-map map-name seq-num
Example:

Router(config)# crypto dynamic-map mymap 10

Creates a dynamic crypto map entry and enters crypto map configuration mode.

Step 4

reverse-route
Example:

Router(config-crypto-map)# reverse-route

Enables RRI for a dynamic crypto map.

Configuring RRI on a Static Crypto Map

Static crypto map entries are grouped into sets. A set is a group of static crypto map entries all with the same static map name but each with a different sequence number. Each static crypto map in the map set can be configured for RRI. Use this task to configure RRI on a static crypto map.

SUMMARY STEPS

1. enable

2. configure terminal

3. crypto map map-name seq-num ipsec-isakmp

4. reverse-route

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

crypto map map-name seq-num ipsec-isakmp
Example:

Router(config)# crypto map to-peer-outside 10 ipsec-isakmp

Enters crypto map configuration mode and creates or modifies a crypto map entry.

Step 4

reverse-route
Example:

Router(config-crypto-map)# reverse-route

Dynamically creates static routes based on crypto ACLs.

Examples

The following example shows how to configure RRI on the static crypto map "to-peer-outside":
crypto map to-peer-outside redundancy replay-interval inbound 1000 outbound 10000
crypto map to-peer-outside 10 ipsec-isakmp 
 set peer 209.165.200.225
 set transform-set trans1 
 match address peer-outside
 reverse-route
What to Do Next

After you have configured RRI, you can enable stateful failover for IPsec and IKE.

Enabling Stateful Failover for IKE and IPsec

Use the following tasks to configure stateful failover for IPsec, IKE, and tunnel protection:

•Enabling Stateful Failover for IKE, page 15

•Enabling Stateful Failover for IPSec, page 15

•Enabling Stateful Failover for Tunnel Protection, page 17

Enabling Stateful Failover for IKE

There is no specific command-line interface (CLI) necessary to enable stateful failover for IKE. It is enabled for a particular VIP address when a stateful failover crypto map is applied to an interface.

Enabling Stateful Failover for IPsec

Use this task to enable stateful failover for IPsec. All IPsec state information is transferred from the active router to the standby router via the SSO redundancy channel that was specified in the task "Enabling SSO."

SUMMARY STEPS

1. enable

2. configure terminal

3. interface type number

4. crypto map map-name [redundancy standby-group-name [stateful]]

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

interface type number
Example:

Router(config)# interface Ethernet 0/0

Defines an interface that has already been configured for redundancy and enters interface configuration mode.

Step 4

crypto map map-name [redundancy standby-group-name [stateful]]
Example:

Router(config-if)# crypto map to-peer-outside redundancy HA-out stateful

Binds the crypto map on the specified interface to the redundancy group.

Note Although the standby group does not have to be the same group that was used when enabling SSO, it does have to be the same group that was used with the standby ip command on this interface.

This crypto map will use the same VIP address for both IKE and IPsec to communicate with peers.

Troubleshooting Tips

To help troubleshoot possible IPsec HA-related problems, issue the debug crypto ipsec ha [detail] [update] command.

Examples

The following example shows how to configure IPsec stateful failover on the crypto map "to-peer-outside":
interface Ethernet0/0
 ip address 209.165.201.1 255.255.255.224
 standby 1 ip 209.165.201.3
 standby 1 preempt
 standby 1 name HA-out
 standby 1 track Ethernet1/0
 crypto map to-peer-outside redundancy HA-out stateful
Enabling Stateful Failover for Tunnel Protection

Use an existing IPsec profile to configure stateful failover for tunnels using IPsec. (You do not configure the tunnel interface as you would with a crypto map configuration.)

Restrictions

The tunnel source address must be a VIP address, and it must not be an interface name.

SUMMARY STEPS

1. enable

2. configure terminal

3. crypto ipsec profile name

4. redundancy standby-group-name stateful

5. exit

6. interface tunnel number

7. tunnel protection ipsec profile name

8. tunnel source virtual-ip-address

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

crypto ipsec profile name
Example:

Router(config)# crypto ipsec profile peer-profile

Defines the IPsec parameters that are to be used for IPsec encryption between two routers and enters crypto map configuration mode.

Step 4

redundancy standby-group-name stateful
Example:

Router(config-crypto-map)# redundancy HA-out stateful

Configures stateful failover for tunnels using IPsec.

Step 5

exit
Example:

Router(config-crypto-map)# exit

Exits crypto map configuration mode.

Step 6

interface tunnel number
Example:

Router(config)# interface tunnel 5

Configures a tunnel interface and enters interface configuration mode

•number—Specifies the number of the interface that you want to create or configure. There is no limit on the number of tunnel interfaces you can create.

Step 7

tunnel protection ipsec profile name
Example:

Router(config-if)# tunnel protection ipsec profile catprofile

Associates a tunnel interface with an IPsec profile.

name—Specifies the name of the IPsec profile; this value must match the name specified in the crypto ipsec profile name command.

Step 8

tunnel source virtual-ip-address
Example:

Router(config-if)# tunnel source 10.1.1.1

Sets source address for a tunnel interface.

•virtual-ip-address—Must be a VIP address.

Note Do not use the interface name as the tunnel source.

Examples

The following example shows how to configure stateful failover for tunnel protection:
crypto ipsec profile peer-profile
  redundancy HA-out stateful
interface Tunnel1
 ip unnumbered Loopback0
 tunnel source 209.165.201.3
 tunnel destination 10.0.0.5
 tunnel protection ipsec profile peer-profile
!
interface Ethernet0/0
 ip address 209.165.201.1 255.255.255.224
 standby 1 ip 209.165.201.3
 standby 1 name HA-out
What to Do Next

After you have configured stateful failover, you can use the CLI to protect, verify, and manage your configurations. For more information on completing these tasks, see the sections "Protecting SSO Traffic" and "Managing and Verifying High Availability Information."

Protecting SSO Traffic

Use this task to secure a redundancy group via an IPsec profile. To configure SSO traffic protection, the active and standby devices must be directly connected to each other via Ethernet networks.

The crypto maps that are automatically generated when protecting SSO traffic are applied to each interface, which corresponds to an IP address that was specified via the local-ip command. Traffic that is destined for an IP address that was specified via the remote-ip command is forced out of the crypto-map-configured interface via an automatically created static host route.

Note If you are certain that the SSO traffic between the redundancy group runs on a physically secure interface, you do not have to configure SSO traffic protection.

SUMMARY STEPS

1. enable

2. configure terminal

3. crypto isakmp key keystring address peer-address

4. crypto ipsec transform-set transform-set-name transform-set-list

5. crypto ipsec profile profile-name

6. set transform-set transform-set-name

7. exit

8. redundancy inter-device

9. security ipsec profile-name

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

crypto isakmp key keystring address peer-address
Example:

Router(config)# crypto isakmp key cisco123 address 0.0.0.0 0.0.0.0

Configures a preshared authentication key.

•peer-address—The SCTP remote IP address.

Step 4

crypto ipsec transform-set transform-set-name transform-set-list
Example:

Router(config)# crypto ipsec transform-set trans2 ah-md5-hmac esp-aes

Configures a transform set that defines the packet format and cryptographic algorithms used for IPsec.

Step 5

crypto ipsec profile profile-name
Example:

Router(config)# crypto ipsec profile sso-secure

Defines an IPsec profile that describes how the traffic will be protected.

Step 6

set transform-set transform-set-name
Example:

Router(config-crypto-map)# set transform-set trans2

Specifies which transform sets can be used with the IPsec profile.

Step 7

exit
Example:

Router(config-crypto-map)# exit

Exits crypto map configuration mode.

Step 8

redundancy inter-device
Example:

Router(config)# redundancy inter-device

Configures redundancy and enters inter-device configuration mode.

Step 9

security ipsec profile-name
Example:

Router(config-red-interdevice)# security ipsec sso-secure

Applies the IPsec profile to the redundancy group communications, protecting all SSO traffic that is passed between the active and standby device.

Examples

The following example shows how to configure SSO traffic protection:
crypto isakmp key cisco123 address 0.0.0.0 0.0.0.0 no-xauth
!
crypto ipsec transform-set trans2 ah-md5-hmac esp-aes 
!         
crypto ipsec profile sso-secure
 set transform-set trans2 
!
redundancy inter-device
 scheme standby HA-out
 security ipsec sso-secure
Managing and Verifying High Availability Information

Use any of the following optional tasks to secure and manage your high availability configurations:

•Managing Anti-Replay Intervals, page 21

•Managing and Verifying HA Configurations, page 22

Managing Anti-Replay Intervals

Use this optional task to modify the interval in which an IP redundancy-enabled crypto map forwards anti-replay updates from the active router to the standby router.

SUMMARY STEPS

1. enable

2. configure terminal

3. crypto map map-name redundancy replay-interval inbound in-value outbound out-value

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

crypto map map-name redundancy replay-interval inbound in-value outbound out-value
Example:

Router(config)# crypto map to-peer-outside redundancy replay-interval inbound 1000 outbound 10000

Modifies the interval at which inbound and outbound replay counters are passed from an active device to a standby device.

•inbound in-value—Number of inbound packets that are processed before an anti-replay update is sent from the active router to the standby router. Default value: one update every 1,000 packets.

•outbound out-value—Number of outbound packets that are processed before an anti-replay update is sent from the active router to the standby router. Default value: one update every 100,000 packets.

Examples

The following example shows how to modify replay counter intervals between the active and standby devices on the crypto map "to-peer-outside":
crypto map to-peer-outside redundancy replay-interval inbound 1000 outbound 10000
crypto map to-peer-outside 10 ipsec-isakmp 
 set peer 209.165.200.225
 set transform-set trans1 
 match address peer-outside
Managing and Verifying HA Configurations

Use any of the steps within this optional task to display and verify the high availability configurations.

SUMMARY STEPS

1. enable

2. show redundancy [states | inter-device]

3. show crypto isakmp sa [active | standby]

4. show crypto ipsec sa [active | standby]

5. show crypto session [active | standby]

6. show crypto ha

7. clear crypto isakmp [active | standby]

8. clear crypto sa [active | standby]

9. clear crypto session [active | standby]

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

show redundancy [states | inter-device]
Example:

Router# show redundancy states

Displays the current state of SSO on the configured device.

After the two devices have negotiated with each other, one device should show an "ACTIVE" state and the other device should show a "STANDBY HOT" state.

Step 3

show crypto isakmp sa [active | standby]
Example:

Router# show crypto isakmp sa active

Displays IKE SAs present on the device.

An "ACTIVE" or "STDBY" state is shown for each SA.

•The active keyword displays only ACTIVE, HA-enabled SAs; The standby keyword displays only STDBY, HA-enabled SAs.

Step 4

show crypto ipsec sa [active | standby]
Example:

Router# show crypto ipsec sa active

Displays IPsec SAs present on the device.

An "ACTIVE" or "STDBY" state is shown for each SA.

•The active keyword displays only ACTIVE, HA-enabled SAs; The standby keyword displays only STDBY, HA-enabled SAs.

Step 5

show crypto session [active | standby]
Example:

Router# show crypto session active

Displays crypto sessions that are currently present on the device.

An "ACTIVE" or "STANDBY" state is shown as part of the state of each session, such as "UP-STANDBY."

Only HA-enabled SAs are shown.

Step 6

show crypto ha
Example:

Router# show crypto ha

Displays all virtual IP addresses that are currently in use by IPsec and IKE.

Step 7

clear crypto isakmp [active | standby]
Example:

Router# clear crypto isakmp active

Clears IKE SAs.

When this command is issued on the standby device, all standby IKE SAs are resynchronized from the active device.

•The active keyword clears only IKE HA-enabled SAs in the active state; the standby keyword clears only IKE HA-enabled SAs in the standby state.

Step 8

clear crypto sa [active | standby]
Example:

Router# clear crypto sa active

Clears IPsec SAs.

When this command is issued on the standby device, all standby IPsec SAs are resynchronized from the active device.

•The active keyword clears only IPsec HA-enabled SAs in the active state; the standby keyword clears only IPsec HA-enabled SAs in the standby state.

Step 9

clear crypto session [active | standby]
Example:

Router# clear crypto session active

Clears both IKE and IPsec SAs.

Any standby SAs will resynchronize from the active device after they are cleared on the standby. Only HA-enabled SAs are cleared from the device.

Examples

Verifying the Active Device:Examples
Router# show redundancy states
       my state = 13 -ACTIVE 
     peer state = 8  -STANDBY HOT 
           Mode = Duplex
        Unit ID = 0
     Split Mode = Disabled
   Manual Swact = Enabled
 Communications = Up
   client count = 7
 client_notification_TMR = 30000 milliseconds
          keep_alive TMR = 4000 milliseconds
        keep_alive count = 0 
    keep_alive threshold = 7 
           RF debug mask = 0x0   
Router# show crypto isakmp sa active
dst             src             state          conn-id slot status
209.165.201.3   209.165.200.225 QM_IDLE              5    0 ACTIVE
Router# show crypto ipsec sa active
interface:Ethernet0/0
    Crypto map tag:to-peer-outside, local addr 209.165.201.3
   protected vrf:(none)
   local  ident (addr/mask/prot/port):(192.168.0.1/255.255.255.255/0/0)
   remote ident (addr/mask/prot/port):(172.16.0.1/255.255.255.255/0/0)
   current_peer 209.165.200.225 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps:3, #pkts encrypt:3, #pkts digest:3
    #pkts decaps:4, #pkts decrypt:4, #pkts verify:4
    #pkts compressed:0, #pkts decompressed:0
    #pkts not compressed:0, #pkts compr. failed:0
    #pkts not decompressed:0, #pkts decompress failed:0
    #send errors 0, #recv errors 0
     local crypto endpt.:209.165.201.3, remote crypto endpt.:209.165.200.225
     path mtu 1500, media mtu 1500
     current outbound spi:0xD42904F0(3559458032)
     inbound esp sas:
      spi:0xD3E9ABD0(3555306448)
        transform:esp-3des ,
        in use settings ={Tunnel, }
        conn id:2006, flow_id:6, crypto map:to-peer-outside
        sa timing:remaining key lifetime (k/sec):(4586265/3542)
             HA last key lifetime sent(k):(4586267)
        ike_cookies:9263635C CA4B4E99 C14E908E 8EE2D79C
        IV size:8 bytes
        replay detection support:Y
        Status:ACTIVE
inbound ah sas:
      spi: 0xF3EE3620(4092474912)
        transform: ah-md5-hmac ,
        in use settings ={Tunnel, }
        conn id: 2006, flow_id: 6, crypto map: to-peer-outside
        sa timing: remaining key lifetime (k/sec): (4586265/3542)
             HA last key lifetime sent(k): (4586267)
        ike_cookies: 9263635C CA4B4E99 C14E908E 8EE2D79C
        replay detection support: Y
        Status: ACTIVE
     inbound pcp sas:
     outbound esp sas:
      spi: 0xD42904F0(3559458032)
        transform: esp-3des ,
        in use settings ={Tunnel, }
        conn id: 2009, flow_id: 9, crypto map: to-peer-outside
        sa timing: remaining key lifetime (k/sec): (4586266/3542)
             HA last key lifetime sent(k): (4586267)
        ike_cookies: 9263635C CA4B4E99 C14E908E 8EE2D79C
        IV size: 8 bytes
        replay detection support: Y
        Status: ACTIVE
     outbound ah sas:
      spi: 0x75251086(1965363334)
        transform: ah-md5-hmac ,
        in use settings ={Tunnel, }
        conn id: 2009, flow_id: 9, crypto map: to-peer-outside
        sa timing: remaining key lifetime (k/sec): (4586266/3542)
             HA last key lifetime sent(k): (4586267)
        ike_cookies: 9263635C CA4B4E99 C14E908E 8EE2D79C
        replay detection support: Y
        Status: ACTIVE
     outbound pcp sas:
Router# show crypto session active
Crypto session current status
Interface: Ethernet0/0
Session status: UP-ACTIVE     
Peer: 209.165.200.225 port 500 
  IKE SA: local 209.165.201.3/500 remote 209.165.200.225/500 Active 
  IKE SA: local 209.165.201.3/500 remote 209.165.200.225/500 Active 
  IPSEC FLOW: permit ip host 192.168.0.1 host 172.16.0.1 
        Active SAs: 4, origin: crypto map
Router# show crypto ha
IKE VIP: 209.165.201.3
  stamp: 74 BA 70 27 9C 4F 7F 81 3A 70 13 C9 65 22 E7 76 
IPSec VIP: 209.165.201.3
IPSec VIP: 255.255.255.253
IPSec VIP: 255.255.255.254
Verifying the Standby Device: Examples
Router# show redundancy states
       my state = 8  -STANDBY HOT 
     peer state = 13 -ACTIVE 
           Mode = Duplex
        Unit ID = 0
     Split Mode = Disabled
   Manual Swact = Enabled
 Communications = Up
   client count = 7
 client_notification_TMR = 30000 milliseconds
          keep_alive TMR = 4000 milliseconds
        keep_alive count = 1 
    keep_alive threshold = 7 
           RF debug mask = 0x0 
Router# show crypto isakmp sa standby
dst             src             state          conn-id slot status
209.165.201.3   209.165.200.225 QM_IDLE              5    0 STDBY 
Router# show crypto ipsec sa standby
interface:Ethernet0/0
    Crypto map tag:to-peer-outside, local addr 209.165.201.3
   protected vrf:(none)
   local  ident (addr/mask/prot/port):(192.168.0.1/255.255.255.255/0/0)
   remote ident (addr/mask/prot/port):(172.16.0.1/255.255.255.255/0/0)
   current_peer 209.165.200.225 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps:0, #pkts encrypt:0, #pkts digest:0
    #pkts decaps:0, #pkts decrypt:0, #pkts verify:0
    #pkts compressed:0, #pkts decompressed:0
    #pkts not compressed:0, #pkts compr. failed:0
    #pkts not decompressed:0, #pkts decompress failed:0
    #send errors 0, #recv errors 0
     local crypto endpt.:209.165.201.3, remote crypto endpt.:209.165.200.225
     path mtu 1500, media mtu 1500
     current outbound spi:0xD42904F0(3559458032)
     inbound esp sas:
      spi:0xD3E9ABD0(3555306448)
        transform:esp-3des ,
        in use settings ={Tunnel, }
        conn id:2012, flow_id:12, crypto map:to-peer-outside
        sa timing:remaining key lifetime (k/sec):(4441561/3486)
             HA last key lifetime sent(k):(4441561)
        ike_cookies:00000000 00000000 00000000 00000000
        IV size:8 bytes
        replay detection support:Y
        Status:STANDBY
     inbound ah sas:
      spi:0xF3EE3620(4092474912)
        transform:ah-md5-hmac ,
        in use settings ={Tunnel, }
        conn id:2012, flow_id:12, crypto map:to-peer-outside
        sa timing:remaining key lifetime (k/sec):(4441561/3486)
             HA last key lifetime sent(k):(4441561)
        ike_cookies:00000000 00000000 00000000 00000000
        replay detection support:Y
        Status:STANDBY
     inbound pcp sas:
     outbound esp sas:
      spi:0xD42904F0(3559458032)
        transform:esp-3des ,
        in use settings ={Tunnel, }
        conn id:2011, flow_id:11, crypto map:to-peer-outside
        sa timing:remaining key lifetime (k/sec):(4441561/3485)
             HA last key lifetime sent(k):(4441561)
        ike_cookies:00000000 00000000 00000000 00000000
        IV size:8 bytes
        replay detection support:Y
        Status:STANDBY
     outbound ah sas:
      spi:0x75251086(1965363334)
        transform:ah-md5-hmac ,
        in use settings ={Tunnel, }
        conn id:2011, flow_id:11, crypto map:to-peer-outside
        sa timing:remaining key lifetime (k/sec):(4441561/3485)
             HA last key lifetime sent(k):(4441561)
        ike_cookies:00000000 00000000 00000000 00000000
        replay detection support:Y
        Status:STANDBY
     outbound pcp sas:
Router# show crypto session standby
Crypto session current status
Interface:Ethernet0/0
Session status:UP-STANDBY    
Peer:209.165.200.225 port 500 
  IKE SA:local 209.165.201.3/500 remote 209.165.200.225/500 Active 
  IPSEC FLOW:permit ip host 192.168.0.1 host 172.16.0.1 
        Active SAs:4, origin:crypto map
Router# show crypto ha
IKE VIP:209.165.201.3
  stamp:74 BA 70 27 9C 4F 7F 81 3A 70 13 C9 65 22 E7 76 
IPSec VIP:209.165.201.3
IPSec VIP:255.255.255.253
IPSec VIP:255.255.255.254
ha-R2#
Verifying the Active and Standby SAs: Example

The following sample output shows SAs of both the active and standby devices:
Router# show crypto isakmp sa
dst             src             state          conn-id slot status
209.165.201.3   209.165.200.225 QM_IDLE              2    0 STDBY 
10.0.0.1        10.0.0.2        QM_IDLE              1    0 ACTIVE
Configuration Examples for Stateful Failover

This section contains the following comprehensive IPsec stateful failover configuration examples:

•Configuring IPSec Stateful Failover: Example, page 27

•Configuring IPSec Stateful Failover for an Easy VPN Server: Example, page 31

Configuring IPsec Stateful Failover: Example

Figure 3 and the following sample outputs from the show running-config command illustrate how to configure stateful failover on two devices—Ha-R1 and Ha-R2.

Figure 3 IPsec Stateful Failover Sample Topology

Stateful Failover Configuration on Ha-R1
Ha-R1# show running-config
Building configuration...
Current configuration :2086 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname ha-R1
!
boot-start-marker
boot-end-marker
!
!
redundancy inter-device
 scheme standby HA-out
 security ipsec sso-secure
!
logging buffered 10000000 debugging
logging rate-limit console 10000
!
!
ipc zone default
 association 1
  no shutdown
  protocol sctp
   local-port 5000
    local-ip 10.0.0.1
   remote-port 5000
    remote-ip 10.0.0.2
!
clock timezone PST 0
no aaa new-model
ip subnet-zero
!
crypto isakmp policy 1
 authentication pre-share
crypto isakmp key cisco123 address 0.0.0.0 0.0.0.0 no-xauth
!         
!
crypto ipsec transform-set trans1 ah-md5-hmac esp-3des 
crypto ipsec transform-set trans2 ah-md5-hmac esp-aes 
!
crypto ipsec profile sso-secure
 set transform-set trans2 
!
!
crypto map to-peer-outside redundancy replay-interval inbound 1000 outbound 10000
crypto map to-peer-outside 10 ipsec-isakmp 
 set peer 209.165.200.225
 set transform-set trans1 
 match address peer-outside
!
!
!
interface Ethernet0/0
 ip address 209.165.201.1 255.255.255.224
 standby 1 ip 209.165.201.3
 standby 1 preempt
 standby 1 name HA-out
 standby 1 track Ethernet1/0
 standby delay reload 120
 crypto map to-peer-outside redundancy HA-out stateful
!
interface Ethernet1/0
 ip address 10.0.0.1 255.255.255.0
 standby 2 ip 10.0.0.3
 standby 2 preempt
 standby 2 name HA-in
 standby delay reload 120
 standby 2 track Ethernet0/0
!
interface Serial2/0
 no ip address
 shutdown
 serial restart-delay 0
!
interface Serial3/0
 no ip address
 shutdown
 serial restart-delay 0
!
ip classless
ip route 0.0.0.0 0.0.0.0 209.165.201.5
ip route 192.168.0.0 255.255.0.0
no ip http server
no ip http secure-server
!
!
!
ip access-list extended peer-outside
 permit ip host 192.168.0.1 host 172.16.0.1
!
!
control-plane
!
!
line con 0
 exec-timeout 0 0
 transport preferred all
 transport output all
line aux 0
 transport preferred all
 transport output all
line vty 0 4
 login
 transport preferred all
 transport input all
 transport output all
!
end
Stateful Failover Configuration on Ha-R2
Ha-R2# show running-config
Building configuration...
Current configuration :2100 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname ha-R2
!
boot-start-marker
boot-end-marker
!
!
redundancy inter-device
 scheme standby HA-out
 security ipsec sso-secure
!
logging buffered 10000000 debugging
logging rate-limit console 10000
!
!
ipc zone default
 association 1
  no shutdown
  protocol sctp
   local-port 5000
    local-ip 10.0.0.2
   remote-port 5000
    remote-ip 10.0.0.1
!
clock timezone PST 0
no aaa new-model
ip subnet-zero
!
!
crypto isakmp policy 1
 authentication pre-share
 lifetime 120
crypto isakmp key cisco123 address 0.0.0.0 0.0.0.0 no-xauth
!
!
crypto ipsec transform-set trans1 ah-md5-hmac esp-3des 
crypto ipsec transform-set trans2 ah-md5-hmac esp-aes 
!
crypto ipsec profile sso-secure
 set transform-set trans2 
!
!
crypto map to-peer-outside redundancy replay-interval inbound 1000 outbound 10000
crypto map to-peer-outside 10 ipsec-isakmp 
 set peer 209.165.200.225
 set transform-set trans1 
 match address peer-outside
!
!
!
interface Ethernet0/0
 ip address 209.165.201.2 255.255.255.224
 standby 1 ip 209.165.201.3
 standby 1 preempt
 standby 1 name HA-out
 standby 1 track Ethernet1/0
 standby delay reload 120
 crypto map to-peer-outside redundancy HA-out stateful
!
interface Ethernet1/0
 ip address 10.0.0.2 255.255.255.0
 standby 2 ip 10.0.0.3
 standby 2 preempt
 standby 2 name HA-in
 standby delay reload 120
 standby 2 track Ethernet0/0
!
interface Serial2/0
 no ip address
 shutdown
 serial restart-delay 0
!
interface Serial3/0
 no ip address
 shutdown
 serial restart-delay 0
!
ip classless
ip route 0.0.0.0 0.0.0.0 209.165.201.5
ip route 192.168.0.0 255.255.0.0
no ip http server
no ip http secure-server
!
!
!
ip access-list extended peer-outside
 permit ip host 192.168.0.1 host 172.16.0.1
!
!
control-plane
!
!
line con 0
 exec-timeout 0 0
 transport preferred all
 transport output all
line aux 0
 transport preferred all
 transport output all
line vty 0 4
 login    
 transport preferred all
 transport input all
 transport output all
!
end
Ha-R2#
Configuring IPsec Stateful Failover for an Easy VPN Server: Example

The following sample outputs from the show running-config command show how to configure stateful failover for a remote access connection via an Easy VPN server:

Stateful Failover for an Easy VPN Server Configuration on RAHA-R1
RAHA-R1# show running-config
Building configuration...
Current configuration :3829 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname RAHA-R1
!
boot-start-marker
boot-end-marker
!
redundancy inter-device
 scheme standby HA-out
!
username remote_user password 0 letmein
!
ipc zone default
 association 1
  no shutdown
  protocol sctp
   local-port 5000
    local-ip 10.0.0.1
   remote-port 5000
    remote-ip 10.0.0.2
!
aaa new-model
!
!
! Enter the following command if you are doing Xauth locally.
aaa authentication login local_xauth local
!
! Enter the following command if you are doing Xauth remotely via RADIUS.
!aaa authentication login radius_xauth group radius
!
! Enter the following command if you are not doing Xauth
!aaa authentication login no_xauth none
!
! Enter the following command if you are doing local group authentication.
aaa authorization network local_auth local 
!
! Enter the following command if you are doing group authentication remotely via RADIUS.
!aaa authorization network radius_auth group radius 
!
!
! Enter the following command if you are doing Xauth remotely via RADIUS.
!
aaa accounting network radius_accounting start-stop group radius
aaa session-id common
ip subnet-zero
!
crypto isakmp policy 1
 encr 3des
 hash md5
 authentication pre-share
 group 2
!
!         
! Enter the following command if you are doing group authentication locally. 
crypto isakmp client configuration group unity
 key cisco123
 domain cisco.com
 pool client-address-pool
!         
!         
crypto ipsec transform-set trans1 esp-3des esp-sha-hmac
!
crypto dynamic-map to-remote-client 10
 set transform-set trans1 
 reverse-route remote-peer
!
! Use this map if you want to do local group authentication and Xauth.
crypto map to_peer_outside_local_xauth client authentication list local_xauth
crypto map to_peer_outside_local_xauth isakmp authorization list local_auth
crypto map to_peer_outside_local_xauth client configuration address respond
crypto map to_peer_outside_local_xauth 10 ipsec-isakmp dynamic to-remote-client 
!
! Use this map if you want to use Radius for group authentication and Xauth.
!crypto map to_peer_outside_radius_xauth isakmp client authentication list radius_xauth
!crypto map to_peer_outside_radius_xauth client accounting list radius_accounting
!crypto map to_peer_outside_radius_xauth isakmp authorization list radius_auth
!crypto map to_peer_outside_radius_xauth isakmp client configuration address respond
!crypto map to_peer_outside_radius_xauth isakmp 10 ipsec-isakmp dynamic to-remote-client 
!
! Use this map if you want to do local group authentication and no Xauth
!crypto map to_peer_outside_no_xauth isakmp authorization list local_auth
!crypto map to_peer_outside_no_xauth configuration address respond
!crypto map to_peer_outside_no_xauth 10 ipsec-isakmp dynamic to-remote-client 
!
interface Ethernet0/0
 ip address 209.165.201.1 255.255.255.224
 standby 1 ip 209.165.201.3
 standby 1 preempt
 standby 1 name HA-out
 standby 1 track Ethernet1/0
 standby delay reload 120
 crypto map to_peer_outside_local_xauth redundancy HA-out stateful
!
interface Ethernet1/0
 ip address 10.0.0.1 255.255.255.0
 standby 2 ip 10.0.0.3
 standby 2 preempt
 standby 2 name HA-in
 standby 2 track Ethernet0/0
 standby delay reload 120
!
! Enable loopback0 if you are using radius for Xauth, group auth, or accounting with 
! crypto HA
!interface loopback0
! ip address 192.168.100.1 255.255.255.255
!
! Enable this command if you are using radius for Xauth, group auth, or accounting with 
! crypto HA
!ip radius source-interface loopback0
!
ip local pool client-address-pool 50.0.0.1 50.0.0.254
ip classless
ip route 0.0.0.0 0.0.0.0 209.165.201.5
ip route 192.168.0.0 255.255.255.0 10.0.0.5
!
radius-server host 192.168.0.0 255.255.0.0 auth-port 1845 acct-port 1846
radius-server key radius123
!
control-plane
! 
!         
line con 0
 exec-timeout 0 0
line aux 0
line vty 0 4
!         
end
Stateful Failover for an Easy VPN Server Configuration on RAHA-R2
RAHA-R2# show running-config
Building configuration...
Current configuration :3829 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname RAHA-R2
!
boot-start-marker
boot-end-marker
!
redundancy inter-device
 scheme standby HA-out
!
username remote_user password 0 letmein
!
ipc zone default
 association 1
  no shutdown
  protocol sctp
   local-port 5000
    local-ip 10.0.0.2
   remote-port 5000
    remote-ip 10.0.0.1
!
aaa new-model
!
!
! Enter the following command if you are doing Xauth locally.
aaa authentication login local_xauth local
!
! Enter the following command if you are doing Xauth remotely via RADIUS.
!aaa authentication login radius_xauth group radius
!
! Enter the following command if you are not doing Xauth.
!aaa authentication login no_xauth none
!
! Enter the following command if you are doing local group authentication.
aaa authorization network local_auth local 
!
! Enter the following command if you are doing group authentication remotely via RADIUS.
!aaa authorization network radius_auth group radius 
!
! 
! Enter the following command if you are doing Xauth remotely via RADIUS.
!aaa accounting network radius_accounting start-stop group radius
aaa session-id common
ip subnet-zero
!
crypto isakmp policy 1
 encr 3des
 hash md5
 authentication pre-share
 group 2
!
!       
! Enter the following commands if you are doing group authentication locally. 
crypto isakmp client configuration group unity
 key cisco123
 domain cisco.com
 pool client-address-pool
!         
!         
crypto ipsec transform-set trans1 esp-3des esp-sha-hmac
!
crypto dynamic-map to-remote-client 10
 set transform-set trans1 
 reverse-route remote-peer
!
!
! Use this map if you want to dolocal group authentication and Xauth.
crypto map to_peer_outside_local_xauth client authentication list local_xauth
crypto map to_peer_outside_local_xauth isakmp authorization list local_auth
crypto map to_peer_outside_local_xauth client configuration address respond
crypto map to_peer_outside_local_xauth 10 ipsec-isakmp dynamic to-remote-client 
!
! Use this map if you want to use Radius for group authentication and Xauth.
!crypto map to_peer_outside_radius_xauth isakmp client authentication list radius_xauth
!crypto map to_peer_outside_radius_xauth client accounting list radius_accounting
!crypto map to_peer_outside_radius_xauth isakmp authorization list radius_auth
!crypto map to_peer_outside_radius_xauth isakmp client configuration address respond
!crypto map to_peer_outside_radius_xauth isakmp 10 ipsec-isakmp dynamic to-remote-client 
!
!
! Use this map if you want to do local authentication and no Xauth.
!crypto map to_peer_outside_no_xauth isakmp authorization list local_auth
!crypto map to_peer_outside_no_xauth configuration address respond
!crypto map to_peer_outside_no_xauth 10 ipsec-isakmp dynamic to-remote-client 
!
interface Ethernet0/0
 ip address 209.165.201.2 255.255.255.224
 standby 1 ip 209.165.201.3
 standby 1 preempt
 standby 1 name HA-out
 standby 1 track Ethernet1/0
 standby delay reload
 crypto map to_peer_outside_local_xauth redundancy HA-out stateful
!
interface Ethernet1/0
 ip address 10.0.0.2 255.255.255.0
 standby 2 ip 10.0.0.3
 standby 2 preempt
 standby 2 name HA-in
 standby 2 track Ethernet0/0
 standby delay reload
!
! Enable loopback0 if you are using radius for Xauth, group auth, or accounting with 
! crypto HA
!interface loopback0
! ip address 192.168.100.1 255.255.255.255
!
! Enable this command if you are using radius for Xauth, group auth, or accounting with 
! crypto HA
!ip radius source-interface loopback0
!
ip local pool client-address-pool 50.0.0.1 50.0.0.254 
ip classless
ip route 0.0.0.0 0.0.0.0 209.165.201.5
ip route 192.168.0.0 255.255.0.0
!
radius-server host 192.168.0.200 auth-port 1845 acct-port 1846
radius-server key radius123
!
control-plane
!         
!         
!         
line con 0
 exec-timeout 0 0
line aux 0
line vty 0 4
!         
end
Additional References

Related Documents

Related Topic

Document Title

Cisco IOS commands

Cisco IOS Master Commands List, All Releases

Security commands

Cisco IOS Security Command Reference

RRI

The section "IPSec VPN High Availability Enhancements" in the Cisco IOS Security Configuration Guide: Secure Connectivity.

HSRP

The section "Configuring the Hot Standby Router Protocol" in the Cisco IOS IP Configuration Guide: Secure Connectivity.

Easy VPN Server

The section"Cisco Easy VPN Remote" in the Cisco IOS Security Configuration Guide: Secure Connectivity.

IKE configuration

The section "Configuring Internet Key Exchange for IPsec VPNs" in the Cisco IOS Security Configuration Guide: Secure Connectivity.

IPsec configuration

The section "Configuring Security for VPNs with IPsec" in the Cisco IOS Security Configuration Guide.

IPsec and IKE commands

Cisco IOS Security Command Reference.

Standards

Standards

Title

None

—

MIBs

MIBs

MIBs Link

None

To locate and download MIBs for selected platforms, Cisco IOS software releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

RFCs

RFCs

Title

None

—

Technical Assistance

Description

Link

The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html

Feature Information for Stateful Failover for IPsec

Table 2 lists the release history for this feature.

Not all commands may be available in your Cisco IOS software release. For release information about a specific command, see the command reference documentation.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS and Catalyst OS software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Note Table 2 lists only the Cisco IOS software release that introduced support for a given feature in a given Cisco IOS software release train. Unless noted otherwise, subsequent releases of that Cisco IOS software release train also support that feature.

Table 2 Feature Information for Stateful Failover for IPsec

Feature Name

Releases

Feature Information

Stateful Failover for IPsec

12.3(11)T

The Stateful Failover for IP Sec feature enables a router to continue processing and forwarding IPsec packets after a planned or unplanned outage occurs. Customers employ a backup (secondary) router that automatically takes over the tasks of the active (primary) router if the active router loses connectivity for any reason.

The following commands were introduced or modified: clear crypto isakmp, clear crypto sa, clear crypto session, crypto map (interface IPsec), crypto map redundancy replay-interval, debug crypto ha, debug crypto ipsec ha, debug crypto isakmp ha, local-ip (IPC transport-SCTP local), local-port, redundancy inter-device, redundancy stateful, remote-ip (IPC transport-SCTP remote), remote-port, scheme, security ipsec, show crypto ha, show crypto ipsec sa, show crypto isakmp sa, show crypto session, show redundancy.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2004-2011 Cisco Systems, Inc. All rights reserved.