Cisco IOS Quality of Service Solutions Configuration Guide, Release 12.4T - ATM Policing by Service Category for SVC/SoftPVC [Cisco IOS Software Releases 12.4 T]

Table Of Contents

ATM Policing by Service Category for SVC/SoftPVC

Feature Overview

Benefits

Related Features and Technologies

Related Documents

Supported Platforms

Supported Standards, MIBs, and RFCs

Configuration Tasks

Configuring ATM Policing by Service Category for SVC/SoftPVC

Verifying ATM Policing by Service Category for SVC/SoftPVC

Troubleshooting Tips

Monitoring and Maintaining ATM Policing by Service Category for SVC/SoftPVC

Example: Monitoring and Maintaining ATM Policing by Service Category for SVC/SoftPVC

Configuration Examples

Non-UBR Traffic Policing: Example

Command Reference

Glossary

ATM Policing by Service Category for SVC/SoftPVC

Feature History

Release

Modification

12.2(4)B

This feature was introduced on the Cisco 6400 NSP.

12.2(13)T

This command was integrated into Cisco IOS Release 12.2(13)T.

This document describes the ATM Policing by Service Category for SVC/SoftPVC feature in Cisco IOS Release 12.2(13)T and includes the following sections:

•Feature Overview

•Supported Platforms

•Supported Standards, MIBs, and RFCs

•Configuration Tasks

•Monitoring and Maintaining ATM Policing by Service Category for SVC/SoftPVC

•Configuration Examples

•Command Reference

•Glossary

Feature Overview

When configured, an ATM switch at the network side of a user-to-network (UNI) interface polices the flow of cells in the forward (into the network) direction of a virtual connection. These traffic policing mechanisms are known as usage parameter control (UPC). With UPC, the switch determines whether received cells comply with the negotiated traffic management values and takes one of the following actions on violating cells:

•Pass the cell without changing the cell loss priority (CLP) bit in the cell header.

•Tag the cell with a CLP bit value of 1.

•Drop (discard) the cell.

The ATM Policing by Service Category for SVC/SoftPVC feature enables you to specify which traffic to police, based on service category, on switched virtual circuits (SVCs) or terminating VCs on the destination end of a soft VC.

For more information on UPC, see the "Traffic and Resource Management" chapter in the Guide to ATM Technology.

Benefits

This feature enables you to select which and how traffic is affected by UPC. For example, you can configure your switch to pass all UBR traffic, but tag all other traffic types.

Related Features and Technologies

•Intelligent early packet discard (EPD)

•Intelligent partial (tail) packet discard

Related Documents

•ATM Switch Router Software Configuration Guide

•ATM and Layer 3 Switch Router Command Reference

•Guide to ATM Technology

•ATM Forum UNI 3.1 Specification

Supported Platforms

This feature is supported on the node switch processor (NSP) of the Cisco 6400 carrier-class broadband aggregator.

Supported Standards, MIBs, and RFCs

Standards

None

MIBs

CISCO-ATM-IF-MIB.my—New objects were created for per-service category SVC UPC intent.

To obtain lists of supported MIBs by platform and Cisco IOS release, and to download MIB modules, go to the Cisco MIB website on Cisco.com at the following URL:

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

RFCs

None

Configuration Tasks

See the following sections for configuration tasks for the ATM Policing by Service Category for SVC/SoftPVC feature. Each task in the list is identified as either required or optional:

•Configuring ATM Policing by Service Category for SVC/SoftPVC (Required)

•Verifying ATM Policing by Service Category for SVC/SoftPVC (Optional)

Configuring ATM Policing by Service Category for SVC/SoftPVC

To configure the ATM Policing by Service Category for SVC/SoftPVC feature, use the following commands beginning in global configuration mode:
Command

Purpose

Step 1

Switch(config)# interface atm slot/subslot/port

Selects the ATM interface.
Step 2
Switch(config-if)# atm svc-upc-intent
[{abr | cbr | vbr-rt | vbr-nrt | ubr}]
{tag | pass | drop}
(Repeat this step for each service category and UPC mode combination.)
Specifies the UPC mode. If no service category is specified, then the UPC mode configuration is applied to all traffic types.
Verifying ATM Policing by Service Category for SVC/SoftPVC

Step 1 Enter the show atm vc or show atm vp EXEC command to display the UPC mode for a particular VC or VP.
Switch# show atm vc int atm 0/0/1 2 120
Interface:ATM0/0/1, Type:oc3suni 
VPI = 2  VCI = 120
Status:DOWN
Time-since-last-status-change:1w1d
Connection-type:PVC 
Cast-type:point-to-multipoint-leaf
Packet-discard-option:disabled
Usage-Parameter-Control (UPC):pass 
Wrr weight:2
Number of OAM-configured connections:0
OAM-configuration:disabled
OAM-states: Not-applicable
Cross-connect-interface:ATM0/0/1, Type:oc3suni 
...
Step 2 Enter the show atm interface EXEC command. If the UPC mode is not the same for all service categories, the "Svc Upc Intent" field displays "by sc."
Switch# show atm interface atm 8/0/1
Interface:     ATM8/0/1        Port-type:     oc3suni
IF Status:     UP              Admin Status:  up
Auto-config:   enabled         AutoCfgState:  completed
IF-Side:       Network         IF-type:       NNI
Uni-type:      not applicable  Uni-version:   not applicable
Max-VPI-bits:  8               Max-VCI-bits:  14
Max-VP:        255             Max-VC:        16383
ConfMaxSvpcVpi:255             CurrMaxSvpcVpi:255
ConfMaxSvccVpi:255             CurrMaxSvccVpi:255
ConfMinSvccVci:35              CurrMinSvccVci:35
Svc Upc Intent:by sc           Signalling:    Enabled
ATM Address for Soft VC:47.0091.8100.0000.0002.b9ae.9301.4000.0c84.0010.00
Configured virtual links:
  PVCLs SoftVCLs   SVCLs   TVCLs   PVPLs SoftVPLs   SVPLs Total-Cfgd Inst-Conns
      3        4       0       0       1        0       0          8          7
Logical ports(VP-tunnels):    0
Input cells:   3036674         Output cells:  3036816
5 minute input rate:            0 bits/sec,       0 cells/sec
5 minute output rate:           0 bits/sec,       0 cells/sec
Input AAL5 pkts:1982638, Output AAL5 pkts:1982687, AAL5 crc errors:0
Troubleshooting Tips

If a VC is not configured with the appropriate UPC mode, make sure that the VC was set up after the atm svc-upc-intent command was configured. Changes to the UPC mode take affect after the VC is torn down and set up again.

Monitoring and Maintaining ATM Policing by Service Category for SVC/SoftPVC

Use the commands listed below to monitor and maintain ATM Policing by Service Category for SVC/SoftPVC:

Command

Purpose

Switch# show atm interface

Displays ATM-specific information about an ATM interface.

Switch# show controllers atm slot/subslot/port

Displays information about a physical port device. Includes dropped (or discarded) cells.

Switch# show atm vc [interface atm slot/subslot/port]

Displays the configured UPC action and intelligent packet discard mechanisms, as well as the number of cells discarded due to UPC violations.

Example: Monitoring and Maintaining ATM Policing by Service Category for SVC/SoftPVC
Switch# show atm vc interface atm 3/0/1.51 51 16 
     Interface: ATM3/0/1.51, Type: oc3suni 
     VPI = 51  VCI = 16 
     Status: DOWN 
     Time-since-last-status-change: 2w0d 
     Connection-type: PVC 
     Cast-type: point-to-point 
     Packet-discard-option: enabled 
     Usage-Parameter-Control (UPC): pass 
     Wrr weight: 32 
     Number of OAM-configured connections: 0 
     OAM-configuration: disabled 
     OAM-states:  Not-applicable 
     Cross-connect-interface: ATM2/0/0, Type: ATM Swi/Proc 
     Cross-connect-VPI = 0 
     Cross-connect-VCI = 73 
     Cross-connect-UPC: pass 
     Cross-connect OAM-configuration: disabled 
     Cross-connect OAM-state:  Not-applicable 
     Encapsulation: AAL5ILMI 
     Threshold Group: 6, Cells queued: 0 
     Rx cells: 0, Tx cells: 0 
     Tx Clp0:0,  Tx Clp1: 0 
     Rx Clp0:0,  Rx Clp1: 0 
     Rx Upc Violations:0, Rx cell drops:0 
     Rx pkts:0, Rx pkt drops:0 
     Rx connection-traffic-table-index: 6 
     Rx service-category: UBR (Unspecified Bit Rate) 
     Rx pcr-clp01: 424 
     Rx scr-clp01: none 
     Rx mcr-clp01: none 
     Rx      cdvt: 1024 (from default for interface) 
     Rx       mbs: none 
     Tx connection-traffic-table-index: 6 
     Tx service-category: UBR (Unspecified Bit Rate) 
     Tx pcr-clp01: 424 
     Tx scr-clp01: none 
     Tx mcr-clp01: none 
     Tx      cdvt: none 
     Tx       mbs: none 
     No AAL5 connection registered
Configuration Examples

This section provides the following configuration example:

•Non-UBR Traffic Policing: Example

Non-UBR Traffic Policing: Example

In the following example, the UBR traffic on ATM 3/0/0 is passed while all other traffic is policed:
Switch(config)# interface atm 3/0/0
Switch(config-if)# atm svc-upc-intent ubr pass
Switch(config-if)# atm svc-upc-intent cbr tag
Switch(config-if)# atm svc-upc-intent vbr-rt tag
Switch(config-if)# atm svc-upc-intent vbr-nrt tag
Switch(config-if)# atm svc-upc-intent abr drop
Command Reference

The following commands are introduced or modified in the feature or features documented in this module. For information about these commands, see the Cisco IOS Quality of Service Solutions Command Reference at http://www.cisco.com/en/US/docs/ios/qos/command/reference/qos_book.html. For information about all Cisco IOS commands, use the Command Lookup Tool at http://tools.cisco.com/Support/CLILookup or a Cisco IOS master commands list.

•atm svc-upc-intent

Glossary

ABR—available bit rate. QoS class defined by the ATM Forum for ATM networks. ABR is used for connections that do not require timing relationships between source and destination. ABR provides no guarantees in terms of cell loss or delay, providing only best-effort service. Traffic sources adjust their transmission rate in response to information they receive describing the status of the network and its capability to successfully deliver data. Compare with CBR, UBR, and VBR.

CBR—constant bit rate. QoS class defined by the ATM Forum for ATM networks. CBR is used for connections that depend on precise clocking to ensure undistorted delivery. Compare with ABR, UBR, and VBR.

CLP—cell loss priority. Field in the ATM cell header that determines the probability of a cell being dropped if the network becomes congested. Cells with CLP = 0 are insured traffic, which is unlikely to be dropped. Cells with CLP = 1 are best-effort traffic, which might be dropped in congested conditions to free up resources to handle insured traffic.

PVC—permanent virtual circuit (or connection). Virtual circuit that is permanently established. PVCs save bandwidth associated with circuit establishment and tear down in situations where certain virtual circuits must exist all the time. In ATM terminology, called a permanent virtual connection. Compare with SVC. See also virtual circuit.

soft PVC—A PVC-SVC hybrid in which only the two terminating virtual connection links (VCLs) at either end are permanent and the rest of the VCLs are switched (SVC). Like the PVC, a soft PVC is permanent and the called party cannot drop the connection. Like the SVC, a soft PVC is automatically rerouted if a switch or link in the path fails.

SVC—switched virtual circuit. Virtual circuit that is dynamically established on demand and is torn down when transmission is complete. SVCs are used in situations where data transmission is sporadic. See also virtual circuit. Called a switched virtual connection in ATM terminology. Compare with PVC.

tagged traffic—ATM cells that have their CLP bit set to 1. If the network is congested, tagged traffic can be dropped to ensure the delivery of higher-priority traffic. Sometimes called DE traffic. See also CLP.

traffic policing—Process used to measure the actual traffic flow across a given connection and compare it to the total admissible traffic flow for that connection. Traffic outside of the agreed upon flow can be tagged (where the CLP bit is set to 1) and can be discarded en route if congestion develops. Traffic policing is used in ATM, Frame Relay, and other types of networks. Also known as admission control, permit processing, rate enforcement, and UPC. See also tagged traffic.

UBR—unspecified bit rate. QoS class defined by the ATM Forum for ATM networks. UBR allows any amount of data up to a specified maximum to be sent across the network but there are no guarantees in terms of cell loss rate and delay. Compare with ABR, CBR, and VBR.

UPC—usage parameter control. See traffic policing.

VBR—variable bit rate. QoS class defined by the ATM Forum for ATM networks. VBR is subdivided into a real time (RT) class and non-real time (NRT) class. VBR (RT) is used for connections in which there is a fixed timing relationship between samples. VBR (NRT) is used for connections in which there is no fixed timing relationship between samples but that still need a guaranteed QoS. Compare with ABR, CBR, and UBR.

virtual circuit—Logical circuit created to ensure reliable communication between two network devices. A virtual circuit is defined by a VPI/VCI pair, and can be either permanent (PVC) or switched (SVC). Virtual circuits are used in Frame Relay and X.25. In ATM, a virtual circuit is called a virtual channel. Sometimes abbreviated VC.

CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco StadiumVision, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn is a service mark; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0804R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

© 2007 Cisco Systems, Inc. All rights reserved.