Cisco IOS Network Management Configuration Guide, Release 15.0 - HTTP 1.1 Web Server and Client [Cisco IOS 15.0M]

Table Of Contents

HTTP 1.1 Web Server and Client

Finding Feature Information

Contents

Information About the HTTP 1.1 Web Server and Client

About HTTP Server General Access Policies

How to Configure HTTP 1.1 Web Server and Client

Configuring the HTTP 1.1 Web Server

Configuring the HTTP Client

Configuration Examples for HTTP 1.1 Web Server

Configuring the HTTP 1.1 Web Server: Example

Verifying HTTP Connectivity

Where to Go Next

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Feature Information for the HTTP 1.1 Web Server and Client

HTTP 1.1 Web Server and Client

First Published: November 20, 2006

Last Updated: September 10, 2010

The HTTP 1.1 Web Server and Client feature provides a consistent interface for users and applications by implementing support for HTTP 1.1 in Cisco IOS software-based devices. When combined with the HTTPS feature, the HTTP 1.1 Web Server and Client feature provides a complete, secure solution for HTTP services between Cisco devices.

This module describes the concepts and the tasks related to configuring the HTTP 1.1 Web Server and Client feature.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for the HTTP 1.1 Web Server and Client" section.

Use Cisco Feature Navigator to find information about platform support and Cisco IOS and Catalyst OS software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

•Information About the HTTP 1.1 Web Server and Client

•How to Configure HTTP 1.1 Web Server and Client

•Configuration Examples for HTTP 1.1 Web Server

•Where to Go Next

•Additional References

•Feature Information for the HTTP 1.1 Web Server and Client

Information About the HTTP 1.1 Web Server and Client

This feature updates the Cisco implementation of the Hypertext Transfer Protocol (HTTP) from 1.0 to 1.1. The HTTP server allows features and applications, such as the Cisco web browser user interface, to be run on your routing device.

The Cisco implementation of HTTP 1.1 is backward-compatible with previous Cisco IOS releases. If you are currently using configurations that enable the HTTP server, no configuration changes are needed, as all defaults remain the same.

The process of enabling and configuring the HTTP server also remains the same as in previous releases. Support for Server Side Includes (SSIs) and HTML forms has not changed. Additional configuration options, in the form of the ip http timeout-policy command and the ip http max-connections command, have been added. These options allow configurable resource limits for the HTTP server. If you do not use these optional commands, the default policies are used.

Remote applications may require that you enable the HTTP server before using them. Applications that use the HTTP server include:

•Cisco web browser user interface, which uses the Cisco IOS Homepage Server, HTTP-based EXEC Server, and HTTP IOS File System (IFS) Server

•VPN Device Manager (VDM) application, which uses the VDM Server and the XML Session Manager (XSM)

•QoS Device Manager (QDM) application, which uses the QDM Server

•IP Phone and Cisco IOS Telephony Service applications, which use the ITS Local Directory Search and IOS Telephony Server (ITS)

No Cisco applications use the HTTP Client in Cisco IOS Release 12.2(15)T.

About HTTP Server General Access Policies

The ip http timeout-policy command allows you to specify general access characteristics for the server by configuring a value for idle time, connection life, and request maximum. By adjusting these values you can configure a general policy; for example, if you want to maximize throughput for HTTP connections, you should configure a policy that minimizes connection overhead. You can configure this type of policy by specifying large values for the life and request options so that each connection stays open longer and more requests are processed for each connection.

Another example would be to configure a policy that minimizes the response time for new connections. You can configure this type of policy by specifying small values for the life and request options so that the connections are quickly released to serve new clients.

A throughput policy would be better for HTTP sessions with dedicated management applications, as it would allow the application to send more requests before the connection is closed, while a response time policy would be better for interactive HTTP sessions, as it would allow more people to connect to the server at the same time without having to wait for connections to become available.

In general, you should configure these options as appropriate for your environment. The value for the idle option should be balanced so that it is large enough not to cause an unwanted request or response timeout on the connection, but small enough that it does not hold a connection open longer than necessary.

Access security policies for the HTTP server are configured using the ip http authentication command, which allows only selective users to access the server, the ip http access-class command, which allows only selective IP hosts to access the server, and the ip http accounting commands command, which specifies a particular command accounting method for HTTP server users.

How to Configure HTTP 1.1 Web Server and Client

This section contains the following tasks:

•Configuring the HTTP 1.1 Web Server

•Configuring the HTTP Client

Configuring the HTTP 1.1 Web Server

Perform this task to enable the HTTP server and configure optional server characteristics. The HTTP server is disabled by default.

Note If you want to configure authentication (step 4), you must configure the authentication type before you begin configuring the HTTP 1.1 web server.

SUMMARY STEPS

1. enable

2. configure terminal

3. ip http server

4. ip http authentication {aaa | enable | local | tacacs} (optional)

5. ip http accounting commands level {default | named-accounting-method-list} (optional)

6. ip http port port-number (optional)

7. ip http path url (optional)

8. ip http access-class access-list-number (optional)

9. ip http max-connections value (optional)

10. ip http timeout-policy idle seconds life seconds requests value (optional)

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

ip http server
Example:

Router(config)# ip http server

Enables the HTTP 1.1 server, including the Cisco web browser user interface.

Note If you are enabling the HTTP over Secure Socket Layer (HTTPS) server using the ip http secure-server command, you should disable the standard HTTP server using the no ip http server command. This command is required to ensure only secure connections to the server.

Step 4

ip http authentication {aaa | enable | local | tacacs}
Example:

Router(config)# ip http authentication local

(Optional) Specifies the authentication method to be used for login when a client connects to the HTTP server. The methods for authentication are:

•aaa—Indicates that the authentication method used for the AAA login service (specified by the aaa authentication login default command) should be used for authentication.

•enable—Indicates that the "enable" password should be used for authentication. (This is the default method.)

•local —Indicates that the login user name, password and privilege level access combination specified in the local system configuration (by the username global configuration command) should be used for authentication and authorization.

•tacacs—Indicates that the TACACS (or XTACACS) server should be used for authentication.

Step 5

ip http accounting commands level {default | named-accounting-method-list}
Example:

Router(config)# ip http accounting commands 15 default

(Optional) Specifies a particular command accounting method for HTTP server users.

•Command accounting for HTTP and HTTPS is automatically enabled when authentication, authorization, and accounting (AAA) is configured on the device. It is not possible to disable accounting for HTTP and HTTPS. HTTP and HTTPS will default to using the global AAA default method list for accounting. The CLI can be used to configure HTTP and HTTPS to use any predefined AAA method list.

•level—Valid privilege level entries are integers from 0 to 15.

•default—Indicates the default accounting method list configured by the aaa accounting commands CLI.

•named-accounting-method-list—Indicates the name of the predefined command accounting method list.

Step 6

ip http port port-number
Example:

Router(config)# ip http port 8080

(Optional) Specifies the server port that should be used for HTTP communication (for example, for the Cisco web browser user interface).

Step 7

ip http path url
Example:

Router(config)# ip http path slot1:

(Optional) Sets the base HTTP path for HTML files. The base path is used to specify the location of the HTTP server files (HTML files) on the local system. Generally, the HTML files are located in system flash memory.

Step 8

ip http access-class access-list-number
Example:

Router(config)# ip http access-class 20

(Optional) Specifies the access list that should be used to allow access to the HTTP server.

Step 9

ip http max-connections value
Example:

Router(config)# ip http max-connections 10

(Optional) Sets the maximum number of concurrent connections to the HTTP sever that will be allowed. The default value is 5.

Step 10

ip http timeout-policy idle seconds life seconds requests value
Example:

Router(config)# ip http timeout-policy idle 30 life 120 requests 100

(Optional) Sets the characteristics that determine how long a connection to the HTTP server should remain open. The characteristics are:

•idle—The maximum number of seconds the connection will be kept open if no data is received or response data cannot be sent out on the connection. Note that a new value may not take effect on any already existing connections. If the server is too busy or the limit on the life time or the number of requests is reached, the connection may be closed sooner. The default value is 180 seconds (3 minutes).

•life—The maximum number of seconds the connection will be kept open, from the time the connection is established. Note that the new value may not take effect on any already existing connections. If the server is too busy or the limit on the idle time or the number of requests is reached, it may close the connection sooner. Also, since the server will not close the connection while actively processing a request, the connection may remain open longer than the specified life time if processing is occurring when the life maximum is reached. In this case, the connection will be closed when processing finishes. The default value is 180 seconds (3 minutes). The maximum value is 86400 seconds (24 hours).

•requests—The maximum limit on the number of requests processed on a persistent connection before it is closed. Note that the new value may not take effect on already existing connections. If the server is too busy or the limit on the idle time or the life time is reached, the connection may be closed before the maximum number of requests are processed. The default value is 1. The maximum value is 86400.

Configuring the HTTP Client

Perform this task to enable the HTTP client and configure optional client characteristics.

The standard HTTP 1.1 client and the secure HTTP client are always enabled. No commands exist to disable the HTTP client. For information about configuring optional characteristics for the HTTPS client, see the HTTPS-HTTP Server and Client with SSL 3.0, Release 12.2(15)T, feature module.

SUMMARY STEPS

1. enable

2. configure terminal

3. ip http client cache {ager interval minutes | memory {file file-size-limit | pool pool-size-limit}

4. ip http client connection {forceclose | idle timeout seconds | retry count | timeout seconds}

5. ip http client password password

6. ip http client proxy-server proxy-name proxy-port port-number

7. ip http client response timeout seconds

8. ip http client source-interface type number

9. ip http client username username

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

ip http client cache {ager interval minutes | memory {file file-size-limit | pool pool-size-limit}
Example:

Router(config)# ip http client cache memory file 5

Configures HTTP client cache.

Step 4

ip http client connection {forceclose | idle timeout seconds | retry count | timeout seconds}
Example:

Router(config)# ip http client connection timeout 10

Configures an HTTP client connection.

Step 5

ip http client password password
Example:

Router(config)# ip http client password pswd1

Configures the default password used for connections to remote HTTP servers.

Step 6

ip http client proxy-server proxy-name proxy-port port-number
Example:

Router(config)# ip http client proxy-server server1 proxy-port 52

Configures an HTTP proxy server.

Step 7

ip http client response timeout seconds
Example:

Router(config)# ip http client response timeout 60

Specifies the timeout value, in seconds, that the HTTP client waits for a response from the server.

Step 8

ip http client source-interface type number
Example:

Router(config)# ip http client source-interface ethernet1/0

Configures a source interface for the HTTP client.

Step 9

ip http client username username
Example:

Router(config)# ip http client user1

Configures the default username used for connections to remote HTTP servers.

Configuration Examples for HTTP 1.1 Web Server

This section provides the following configuration examples:

•Configuring the HTTP 1.1 Web Server: Example

•Verifying HTTP Connectivity

Configuring the HTTP 1.1 Web Server: Example

The following example shows a typical configuration that enables the server and sets some of the characteristics:
ip http server
ip http authentication aaa
ip http accounting commands 15 default
ip http path flash:
ip access-list standard 20 
 permit 209.165.202.130 0.0.0.255 
 permit 209.165.201.1 0.0.255.255 
 permit 209.165.200.225 0.255.255.255 
! (Note: all other access implicitly denied)
 end 
ip http access-class 10
ip http max-connections 10
ip http accounting commands 1 oneacct
In the following example, a Throughput timeout policy is applied. This configuration would allow each connection to be idle a maximum of 30 seconds (approximately). Each connection will remain open (be "alive") until either the HTTP server has been busy processing requests for approximately 2 minutes (120 seconds) or until approximately100 requests have been processed.
ip http timeout-policy idle 30 life 120 requests 100 
In the following example, a Response Time timeout policy is applied. This configuration would allow each connection to be idle a maximum of 30 seconds (approximately). Each connection will be closed as soon as the first request has been processed.
ip http timeout-policy idle 30 life 30 requests 1 
Verifying HTTP Connectivity

To verify remote connectivity to the HTTP server, enter the system IP address in a web browser, followed by a colon and the appropriate port number (80 is the default port number).

For example, if the system IP address is 209.165.202.129 and the port number is 8080, enter http://209.165.202.129:8080 as the URL in a web browser.

If HTTP authentication is configured, a login dialog box will appear. Enter the appropriate username and password. If the default login authentication method of "enable" is configured, you may leave the username field blank, and use the "enable" password to log in.

The system home page should appear in your browser.

Where to Go Next

For information about secure HTTP connections using Secure Sockets Layer (SSL) 3.0, refer to the HTTPS - HTTP with SSL 3.0, Release 12.2(15)T, feature module at: http://www.cisco.com/en/US/docs/ios/12_2t/12_2t15/feature/guide/ftsslsht.html

Additional References

The following sections provide references related to the HTTP 1.1 Web Server and Client.

Related Documents

Related Topic

Document Title

HTTPS

•HTTPS—HTTP with SSL 3.0 feature module

•Firewall Support of HTTPS Authentication Proxy feature module

HTTP commands

Cisco IOS Network Management Command Reference

Standards

Standard

Title

No specific standards are supported by this feature. Note that HTTP 1.1, as defined in RFC 2616, is currently classified as a "Standards Track" document by the IETF.

—

MIBs

MIB

MIBs Link

•No specific MIBs are supported for this feature.

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

RFCs

RFC¹

Title

RFC 2616

Hypertext Transfer Protocol -- HTTP/1.1

¹Not all supported RFCs are listed.

The Cisco implementation of the HTTP version 1.1 supports a subset of elements defined in RFC 2616. Following is a list of supported RFC 2616 headers:

•Allow (Only GET, HEAD, and POST methods are supported)

•Authorization, WWW-Authenticate - Basic authentication only

•Cache-control

•Chunked Transfer Encoding

•Connection close

•Content-Encoding

•Content-Language

•Content-Length

•Content-Type

•Date, Expires

•Location

Technical Assistance

Description

Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/techsupport

Feature Information for the HTTP 1.1 Web Server and Client

Table 1 lists the features in this module and provides links to specific configuration information. Only features that were introduced or modified in Cisco IOS Release 12.4T or Cisco IOS Release 12.2SR or a later release appear in the table.

Not all commands may be available in your Cisco IOS software release. For release information about a specific command, see the command reference documentation.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS and Catalyst OS software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Note Table 1 lists only the Cisco IOS software release that introduced support for a given feature in a given Cisco IOS software release train. Unless noted otherwise, subsequent releases of that Cisco IOS software release train also support that feature.

Table 1 Feature Information for HTTP 1.1 Web Server and Client

Feature Name

Releases

Feature Information

HTTP 1.1 Web Server and Client

12.2(15)T
12.4(15)T
12.2(33)SRC
12.2(33)SB
Cisco IOS XE 3.1.0SG

The HTTP 1.1 Web Server and Client feature provides a consistent interface for users and applications by implementing support for HTTP 1.1 in Cisco IOS software-based devices. When combined with the HTTPS feature, the HTTP 1.1 Web Server and Client feature provides a complete, secure solution for HTTP services between Cisco devices.

This entire module provides information about this feature.

The following commands were introduced or modified by this feature: debug ip http all, debug ip http client, ip http access-class, ip http authentication, ip http client cache, ip http client connection, ip http client password, ip http client proxy-server, ip http client response timeout, ip http client source-interface, ip http client username, ip http max-connections, ip http path, ip http port, ip http server, ip http timeout-policy, show ip http client, show ip http client connection, show ip http client history, show ip http client session-module, show ip http server, show ip http server secure status.

HTTP TACAC+ Accounting Support

12.4(15)T
12.2(33)SRC
12.2(33)SB

The HTTP TACAC+ Accounting Support feature introduces the ip http accounting commands command. This command is used to specify a particular command accounting method for HTTP server users. Command accounting provides information about the commands for a specified privilege level that are being executed on a device. Each command accounting record corresponds to one IOS command executed at its respective privilege level, as well as the date and time the command was executed, and the user who executed it. The following sections provide information about this feature:

•Configuring the HTTP 1.1 Web Server

The following commands were introduced or modified by this feature: ip http accounting commands.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

© 2006-2010 Cisco Systems, Inc. All rights reserved.