Cisco IOS IP Routing Protocols Configuration Guide, Release 12.2SR - OSPF Support for Multi-VRF on CE Routers [Cisco IOS Software Releases 12.2 SR]

Table Of Contents

OSPF Support for Multi-VRF on CE Routers

Contents

Information About OSPF Support for Multi-VRF on CE Routers

Benefits of OSPF Multi-VRF Support

How to Configure OSPF Support for Multi-VRF on CE Routers

Configuring the Multi-VRF Capability for OSPF Routing

Prerequisites

Verifying the OSPF Multi-VRF Configuration

Configuration Examples for OSPF Support for Multi-VRF on CE Routers

Configuring the Multi-VRF Capability Example

Verifying the OSPF Multi-VRF Configuration Example

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Command Reference

Glossary

OSPF Support for Multi-VRF on CE Routers

The OSPF Support for Multi-VRF on CE Routers feature provides the capability of suppressing provider edge (PE) checks that are needed to prevent loops when the PE is performing a mutual redistribution of packets between the OSPF and BGP protocols. When VPN routing and forward (VRF) is used on a router that is not a PE (that is, one that is not running BGP), the checks can be turned off to allow for correct population of the VRF routing table with routes to IP prefixes.

OSPF multi-VRF allows you to split the router into multiple virtual routers, where each router contains its own set of interfaces, routing table, and forwarding table.

Feature Specifications for the OSPF Support for Multi-VRF on CE Routers Feature

Feature History

Release

Modification

12.0(21)ST

This feature was introduced.

12.0(22)S

This feature was integrated into Cisco IOS Release 12.0(22)S.

12.2(8)B

This feature was integrated into Cisco IOS Release 12.2(8)B.

12.2(13)T

This feature was integrated into Cisco IOS Release 12.2(13)T.

12.2(14)S

This feature was integrated into Cisco IOS Release 12.2(14)S.

Supported Platforms

For information about platforms supported in Cisco IOS Release 12.0(21)ST, 12.0(22)S, 12.2(13)T, and 12.2(14)S, refer to Cisco Feature Navigator. Cisco Feature Navigator does not support Cisco IOS Release 12.2(8)B.

Determining Platform Support Through Cisco Feature Navigator

Cisco IOS software is packaged in feature sets that are supported on specific platforms. To get updated information regarding platform support for this feature, access Cisco Feature Navigator. Cisco Feature Navigator dynamically updates the list of supported platforms as new platform support is added for the feature.

Cisco Feature Navigator is a web-based tool that enables you to determine which Cisco IOS software images support a specific set of features and which features are supported in a specific Cisco IOS image. You can search by feature or release. Under the release section, you can compare releases side by side to display both the features unique to each software release and the features in common.

To access Cisco Feature Navigator, you must have an account on Cisco.com. If you have forgotten or lost your account information, send a blank e-mail to cco-locksmith@cisco.com. An automatic check will verify that your e-mail address is registered with Cisco.com. If the check is successful, account details with a new random password will be e-mailed to you. Qualified users can establish an account on Cisco.com by following the directions found at this URL:

http://www.cisco.com/register

Cisco Feature Navigator is updated regularly when major Cisco IOS software releases and technology releases occur. For the most current information, go to the Cisco Feature Navigator home page at the following URL:

http://www.cisco.com/go/fn

Availability of Cisco IOS Software Images

Platform support for particular Cisco IOS software releases is dependent on the availability of the software images for those platforms. Software images for some platforms may be deferred, delayed, or changed without prior notice. For updated information about platform support and availability of software images for each Cisco IOS software release, refer to the online release notes or, if supported, Cisco Feature Navigator.

Contents

•Information About OSPF Support for Multi-VRF on CE Routers

•How to Configure OSPF Support for Multi-VRF on CE Routers

•Configuration Examples for OSPF Support for Multi-VRF on CE Routers

•Additional References

•Command Reference

•Glossary

Information About OSPF Support for Multi-VRF on CE Routers

Before you configure OSPF support for multi-VRF on CE routers, you should understand the following concepts:

•Benefits of OSPF Multi-VRF Support

Benefits of OSPF Multi-VRF Support

The OSPF Support for Multi-VRF on CE Routers feature provides the capability of suppressing provider edge (PE) checks that are needed to prevent loops when the PE is performing a mutual redistribution of packets between the OSPF and BGP protocols. When VPN routing and forward (VRF) is used on a router that is not a PE (that is, one that is not running BGP), the checks can be turned off to allow for correct population of the VRF routing table with routes to IP prefixes.

OSPF multi-VRF allows you to split the router into multiple virtual routers, where each router contains its own set of interfaces, routing table, and forwarding table. OSPF multi-VRF gives you the ability to segment parts of your network and configure those segments to perform specific functions, yet still maintain correct routing information.

How to Configure OSPF Support for Multi-VRF on CE Routers

This section contains the following procedures:

•Configuring the Multi-VRF Capability for OSPF Routing

•Verifying the OSPF Multi-VRF Configuration

Configuring the Multi-VRF Capability for OSPF Routing

This section describes how to configure the multi-VRF for OSPF routing. This task assumes that you have already configured a VRF. For a complete VRF configuration example, see the "Configuring the Multi-VRF Capability Example" section.

Prerequisites

CEF must be running on the network.

SUMMARY STEPS

1. enable

2. show ip ospf [process-id]

3. configure terminal

4. router ospf process-id [vrf vpn-name]

5. capability vrf-lite

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables higher privilege levels, such as privileged EXEC mode.

•Enter your password if prompted.

Step 2

show ip ospf [process-id]
Example:

Router> show ip ospf 1

Displays the status of the router. If the display indicates that the router is connected to the VPN backbone, you can use the capability vrf-lite command to decouple the PE router from the VPN backbone.

Step 3

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 4

router ospf process-id [vrf vpn-name]
Example:

Router(config)# router ospf 1 vrf grc

Enables OSPF routing and enters router configuration mode.

•The process-id argument identifies the OSPF process.

•Use the vrf keyword and vpn-name argument to identify a VPN.

Step 5

capability vrf-lite
Example:

Router(config)# capability vrf-lite

Applies the multi-VRF capability to the OSPF process.

Verifying the OSPF Multi-VRF Configuration

No specific debug or show commands are associated with this feature. You can verify the success of the OSPF multi-VRF configuration by using the show ip ospf [process-id] command to verify that the router is not connected to the VPN backbone.

This output from the show ip ospf process command indicates that the PE router is currently connected to the backbone.
Router# show ip ospf 12
 Routing Process "ospf 12" with ID 151.1.1.1 and Domain ID 0.0.0.12
 Supports only single TOS(TOS0) routes
 Supports opaque LSA
 Connected to MPLS VPN Superbackbone
 SPF schedule delay 5 secs, Hold time between two SPFs 10 secs
 Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs
 Number of external LSA 0. Checksum Sum 0x0     
 Number of opaque AS LSA 0. Checksum Sum 0x0     
 Number of DCbitless external and opaque AS LSA 0
 Number of DoNotAge external and opaque AS LSA 0
 Number of areas in this router is 0. 0 normal 0 stub 0 nssa
 External flood list length 0
When the OSPF VRF process is configured with the capability vrf-lite command under the router ospf command, the "Connected to MPLS VPN Superbackbone" line will not be present in the display.

Configuration Examples for OSPF Support for Multi-VRF on CE Routers

This section provides the following configuration examples:

•Configuring the Multi-VRF Capability Example

•Verifying the OSPF Multi-VRF Configuration Example

Configuring the Multi-VRF Capability Example

This example shows a basic OSPF network with a VRF named grc configured. The capability vrf-lite command is entered to suppress the PE checks.
!
ip cef
ip vrf grc
   rd 1:1
interface Serial2/0
  ip vrf forwarding grc
  ip address 192.168.1.1 255.255.255.252
!
interface Serial3/0
  ip vrf forwarding grc
  ip address 192.168.2.1 255.255.255.252
...
!
router ospf 9000 vrf grc
  log-adjacency-changes
  capability vrf-lite
  redistribute rip metric 1 subnets
  network 192.168.1.0 0.0.0.255 area 0
!
router rip
  address-family ipv4 vrf grc
  redistribute ospf 9000 vrf grc
  network network 192.168.2.0
  no auto-summary
  end
Router# show ip route vrf grc
Routing Table: grc
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
O IA 192.168.192.0/24 [110/138] via 192.168.1.13, 00:06:08, Serial2/0
                      [110/138] via 192.168.1.9, 00:06:08, Serial3/0
O IA 192.168.242.0/24 [110/74] via 192.168.1.13, 00:06:08, Serial2/0
O IA 192.168.193.0/24 [110/148] via 192.168.1.13, 00:06:08, Serial2/0
                      [110/148] via 192.168.1.9, 00:06:08, Serial3/0
O IA 192.168.128.0/24 [110/74] via 192.168.1.9, 00:06:08, Serial3/0
O IA 192.168.129.0/24 [110/84] via 192.168.1.9, 00:06:08, Serial3/0
O IA 192.168.130.0/24 [110/84] via 192.168.1.9, 00:06:08, Serial3/0
     172.16.0.0/24 is subnetted, 2 subnets
O E2    172.16.9.0 [110/5] via 192.168.1.13, 00:06:08, Serial2/0
O E2    172.16.10.0 [110/5] via 192.168.1.13, 00:06:08, Serial2/0
O IA 192.168.131.0/24 [110/94] via 192.168.1.9, 00:06:20, Serial3/0
     192.168.1.0/30 is subnetted, 4 subnets
C       192.168.1.8 is directly connected, Serial3/0
C       192.168.1.12 is directly connected, Serial2/0
O       192.168.1.0 [110/128] via 192.168.1.9, 00:06:20, Serial3/0
O       192.168.1.4 [110/128] via 192.168.1.13, 00:06:20, Serial2/0
Verifying the OSPF Multi-VRF Configuration Example

This example illustrates the output display from the show ip ospf process command after OSPF multi-VRF has been configured on the router.
Router# show ip ospf database external 172.16.0.0 self
            OSPF Router with ID (10.0.0.1) (Process ID 100)
                 Type-5 AS External Link States
   LS age: 175
   Options: (No TOS-capability, DC)
   LS Type: AS External Link
   Link State ID: 172.16.0.0 (External Network Number )
   Advertising Router: 10.0.0.1
   LS Seq Number: 80000001
   Checksum: 0xEA9E
   Length: 36
   Network Mask: /8
         Metric Type: 2 (Larger than any link state path)
         MTID: 0
         Metric: 20
         Forward Address: 0.0.0.0
         External Route Tag: 0
Additional References

For additional information related to OSPF support for multi-VRF on CE routers, refer to the following references:

Related Documents

Related Topic

Document Title

Configuring OSPF

Cisco IOS IP Routing Protocols Configuration Guide

Multiprotocol Label Switching (MPLS)

Cisco IOS Switching Services Configuration Guide

Standards

Standards¹

Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

—

¹Not all supported standards are listed.

MIBs

MIBs¹

MIBs Link

No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

To obtain lists of supported MIBs by platform and Cisco IOS release, and to download MIB modules, go to the Cisco MIB website on Cisco.com at the following URL:

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

¹Not all supported MIBs are listed.

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://tools.cisco.com/ITDIT/MIBS/servlet/index

If Cisco MIB Locator does not support the MIB information that you need, you can also obtain a list of supported MIBs and download MIBs from the Cisco MIBs page at the following URL:

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

To access Cisco MIB Locator, you must have an account on Cisco.com. If you have forgotten or lost your account information, send a blank e-mail to cco-locksmith@cisco.com. An automatic check will verify that your e-mail address is registered with Cisco.com. If the check is successful, account details with a new random password will be e-mailed to you. Qualified users can establish an account on Cisco.com by following the directions found at this URL:

http://www.cisco.com/register

RFCs

RFCs¹

Title

No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.

—

¹Not all supported RFCs are listed.

Technical Assistance

Description

Link

Technical Assistance Center (TAC) home page, containing 30,000 pages of searchable technical content, including links to products, technologies, solutions, technical tips, tools, and lots more. Registered Cisco.com users can log in from this page to access even more content.

http://www.cisco.com/public/support/tac/home.shtml

Command Reference

The following commands are introduced or modified in the feature or features documented in this module. For information about these commands, see the Cisco IOS IP Routing Protocols Command Reference at http://www.cisco.com/en/US/docs/ios/iproute/command/reference/irp_book.html. For information about all Cisco IOS commands, go to the Command Lookup Tool at http://tools.cisco.com/Support/CLILookup or to the Cisco IOS Master Commands List.

•capability vrf-lite

Glossary

CE Router—Customer Edge router, an edge router in the C network, defined as a C router which attaches directly to a P router.

C Network—Customer (enterprise or service provider) network.

C Router—Customer router, a router in the C network.

LSA—link-state advertisement. Broadcast packet used by link-state protocols that contains information about neighbors and path costs. LSAs are used by the receiving routers to maintain their routing tables.

PE Router—Provider Edge router, an edge router in the P network, defined as a P router which attaches directly to a C router.

P Network—MPLS-capable service provider core network. P routers perform MPLS.

P Router—Provider router, a router in the P network.

VRF—VPN Routing and Forwarding.

CCDE, CCSI, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco Nurse Connect, Cisco Stackpower, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0903R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

© 2008 Cisco Systems, Inc. All rights reserved.