Table Of Contents

Hiding the Internal Topology Information Embedded Within the History-info Header at the Cisco UBE

Restrictions for Hiding the Internal Topology Information Embedded Within the History-info Header at the Cisco UBE

Hiding Internal Toplogy Information in History-info Header at global level

Hiding Internal Toplogy Information in History-info Header at the Dial-Peer Level

Hiding the Internal Topology Information Embedded Within the History-info Header at the Cisco UBE

SIP History-info stores information on address, topology and so on. Cisco UBE has the address hiding security feature where only the host section of a History-Info header is masked with the CUBE address. However, it does not hide the topology information like the details of the targets where a request was tried upon. It is important to strip the topology information from Cisco UBE before it is passed on to an external device. When the topology hiding for history-info is enabled, the diversion headers are also stripped from the history-info header. Topology information hiding has to be enabled on both inbound and outbound call legs. For example, if topology informatione is enabled only on the outbound dial-peer, this results in stripping all the History-info headers it received from the inbound leg and it sends just the single History-info header. However, on the inbound leg, all the History-info headers received from the outbound leg will be passed on to the external devices. If this feature is enabled on both inbound and outbound dialpeers, then the History-info headers will be stripped for both inbound and outbound legs of Cisco UBE.

Restrictions for Hiding the Internal Topology Information Embedded Within the History-info Header at the Cisco UBE

•The user needs to be in the same network as the network in which the call is received.

•Topology hiding will result in the History-Info headers received on one call leg to be stripped on the other leg and this could result in the call-routing functionality to disfunction. Hence, topology hiding and call-routing are mutually exclusive and cannot function together.

This section contains the following procedures:

•Hiding Internal Toplogy Information in History-info Header at global level

•Hiding Internal Toplogy Information in History-info Header at the Dial-Peer Level

Hiding Internal Toplogy Information in History-info Header at global level

Perform this task to hide topology information in history-info header at a global level in SIP configuration (conf-serv-sip) mode.

SUMMARY STEPS

1. enable

2. configure terminal

3. voice service voip

4. sip

5. privacy policy strip diversion

6. privacy policy strip history-info

7. exit

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: Router> enable	Enters privileged EXEC mode, or other security level set by a system administrator. •Enter your password if prompted.
Step 2	configure terminal Example: Router# configure terminal	Enters global configuration mode.
Step 3	voice service voip Example: Router(config)# voice service voip	Enters voice service VoIP configuration mode.
Step 4	sip Example: Router(conf-voi-serv)# sip	Enters SIP configuration mode.
Step 5	privacy policy strip diversion Example: Router(conf-serv-sip)# privacy policy strip history-info	Srips the diversion headers received from the next call leg
Step 6	privacy policy strip history-info Example: Router(conf-serv-sip)# privacy policy strip history-info	Strips the topology information from the history-info header.
Step 7	exit Example: Router(conf-serv-sip)# exit	Exits the current mode.

Hiding Internal Toplogy Information in History-info Header at the Dial-Peer Level

Perform this task to hide topology information in history-info header header support at the dial-peer level, in dial peer voice configuration (config-dial-peer) mode.

SUMMARY STEPS

1. enable

2. configure terminal

3. dial-peer voice tag voip

4. voice class sip privacy policy strip diversion

5. voice class sip privacy policy strip history-info

6. exit

DETAILED STEPS

	Command or Action	Purpose
Step 1	enable Example: Router> enable	Enters privileged EXEC mode, or other security level set by a system administrator. •Enter your password if prompted.
Step 2	configure terminal Example: Router# configure terminal	Enters global configuration mode.
Step 3	dial-peer voice tag voip Example: Router(config)# dial-peer voice 2 voip	Enters dial peer VoIP configuration mode.
Step 4	voice class sip privacy policy strip diversion Example: Router(config-dial-peer)# voice-class sip call-route history-info	Srips the diversion headers received from the next call leg.
Step 5	voice class sip privacy policy strip history-info Example: Router(conf-serv-sip)# privacy policy strip history-info	Strips the topology information from the history-info header.
Step 6	exit Example: Router(config-dial-peer)# exit	Exits the current mode.