This documentation has been moved - Implementing Static Routes for IPv6 [Support]

Table Of Contents

Implementing Static Routes for IPv6

Finding Feature Information

Contents

Prerequisites for Implementing Static Routes for IPv6

Restrictions for Implementing Static Routes for IPv6

Information About Implementing Static Routes for IPv6

Static Routes

Directly Attached Static Routes

Recursive Static Routes

Fully Specified Static Routes

Floating Static Routes

How to Implement Static Routes for IPv6

Configuring a Static IPv6 Route

Configuring a Floating Static IPv6 Route

Verifying Static IPv6 Route Configuration and Operation

Examples

Configuration Examples for Implementing Static Routes for IPv6

Example: Configuring Manual Summarization

Example: Configuring Traffic Discard

Example: Configuring a Fixed Default Route

Example: Configuring a Floating Static Route

Where to Go Next

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Feature Information for Implementing Static Routes for IPv6

Implementing Static Routes for IPv6

First Published: May 5, 2008

Last Updated: February 3, 2010

This module describes how to configure static routes for IPv6. Routing defines the paths over which packets travel in the network. Manually configured static routes may be used instead of dynamic routing protocols for smaller networks or for sections of a network that have only one path to an outside network. Lack of redundancy limits the usefulness of static routes, and in larger networks manual reconfiguration of routes can become a large administrative overhead.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for Implementing Static Routes for IPv6" section.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

•Prerequisites for Implementing Static Routes for IPv6

•Restrictions for Implementing Static Routes for IPv6

•Information About Implementing Static Routes for IPv6

•How to Implement Static Routes for IPv6

•Configuration Examples for Implementing Static Routes for IPv6

•Additional References

•Feature Information for Implementing Static Routes for IPv6

Prerequisites for Implementing Static Routes for IPv6

•This document assumes that you are familiar with IPv4. Refer to the publications referenced in the "Related Documents" section for IPv4 configuration and command reference information. Any differences in functions between the IPv4 and IPv6 environments are documented in the Implementing IPv6 Addressing and Basic Connectivity module and the Cisco IOS IPv6 Command Reference.

•Before configuring the router with a static IPv6 route you must enable the forwarding of IPv6 packets using the ipv6 unicast-routing global configuration command, enable IPv6 on at least one interface, and configure an IPv6 address on that interface. For details on basic IPv6 connectivity tasks, refer to the Implementing IPv6 Addressing and Basic Connectivity module.

Restrictions for Implementing Static Routes for IPv6

•IPv6 static routes do not support the tag and permanent keywords of the IPv4 ip route command.

•IPv6 does not support inserting static routes into virtual routing and forwarding (VRF) tables.

Information About Implementing Static Routes for IPv6

•Static Routes

•Directly Attached Static Routes

•Recursive Static Routes

•Fully Specified Static Routes

•Floating Static Routes

Static Routes

Networking devices forward packets using route information that is either manually configured or dynamically learned using a routing protocol. Static routes are manually configured and define an explicit path between two networking devices. Unlike a dynamic routing protocol, static routes are not automatically updated and must be manually reconfigured if the network topology changes. The benefits of using static routes include security and resource efficiency. Static routes use less bandwidth than dynamic routing protocols and no CPU cycles are used to calculate and communicate routes. The main disadvantage to using static routes is the lack of automatic reconfiguration if the network topology changes.

Static routes can be redistributed into dynamic routing protocols, but routes generated by dynamic routing protocols cannot be redistributed into the static routing table. No algorithm exists to prevent the configuration of routing loops that use static routes.

Static routes are useful for smaller networks with only one path to an outside network and to provide security for a larger network for certain types of traffic or links to other networks that need more control. In general, most networks use dynamic routing protocols to communicate between networking devices, but may have one or two static routes configured for special cases.

Directly Attached Static Routes

In directly attached static routes, only the output interface is specified. The destination is assumed to be directly attached to this interface, so the packet destination is used as the next-hop address. This example shows such a definition:
ipv6 route 2001:DB8::/32 gigabitethernet1/0/0 
The example specifies that all destinations with address prefix 2001:DB8::/32 are directly reachable through interface GigabitEthernet1/0/0.

Directly attached static routes are candidates for insertion in the IPv6 routing table only if they refer to a valid IPv6 interface; that is, an interface that is both up and has IPv6 enabled on it.

Recursive Static Routes

In a recursive static route, only the next hop is specified. The output interface is derived from the next hop. This example shows such a definition:
ipv6 route 2001:DB8::/32 2001:DB8:3000:1
This example specifies that all destinations with address prefix 2001:DB8::/32 are reachable via the host with address 2001:DB8:3000:1.

A recursive static route is valid (that is, it is a candidate for insertion in the IPv6 routing table) only when the specified next hop resolves, either directly or indirectly, to a valid IPv6 output interface, provided the route does not self-recurse, and the recursion depth does not exceed the maximum IPv6 forwarding recursion depth.

A route self-recurses if it is itself used to resolve its own next hop. For example, suppose we have the following routes in the IPv6 routing table:
IPv6 Routing Table - 9 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
       U - Per-user Static route
       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea
       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
R   2001:DB8::/32 [130/0]
     via ::, Serial2/0
B   2001:DB8:3000:0/16 [200/45]
     Via 2001:DB8::0104
The following examples defines a recursive IPv6 static route:
ipv6 route 
2001:DB8::/32 2001:0BD8:3000:1
This static route will not be inserted into the IPv6 routing table because it is self-recursive. The next hop of the static route, 2001:DB8:3000:1, resolves via the BGP route 2001:DB8:3000:0/16, which is itself a recursive route (that is, it only specifies a next hop). The next hop of the BGP route, 2001:DB8::0104, resolves via the static route. Therefore, the static route would be used to resolve its own next hop.

It is not normally useful to manually configure a self-recursive static route, although it is not prohibited. However, a recursive static route that has been inserted in the IPv6 routing table may become self-recursive as a result of some transient change in the network learned through a dynamic routing protocol. If this occurs, the fact that the static route has become self-recursive will be detected and it will be removed from the IPv6 routing table, although not from the configuration. A subsequent network change may cause the static route to no longer be self-recursive, in which case it will be reinserted in the IPv6 routing table.

Fully Specified Static Routes

In a fully specified static route, both the output interface and the next hop are specified. This form of static route is used when the output interface is a multi-access one and it is necessary to explicitly identify the next hop. The next hop must be directly attached to the specified output interface. The following example shows a definition of a fully specified static route:
ipv6 route 2001:DB8:/32 gigabitethernet1/0/0 2001:DB8:3000:1
A fully specified route is valid (that is, a candidate for insertion into the IPv6 routing table) when the specified IPv6 interface is IPv6-enabled and up.

Floating Static Routes

Floating static routes are static routes that are used to back up dynamic routes learned through configured routing protocols. A floating static route is configured with a higher administrative distance than the dynamic routing protocol it is backing up. As a result, the dynamic route learned through the routing protocol is always used in preference to the floating static route. If the dynamic route learned through the routing protocol is lost, the floating static route will be used in its place. The following example defines a floating static route:
ipv6 route 2001:DB8:/32 gigabitethernet1/0/0 2001:DB8:3000:1 210
Any of the three types of IPv6 static routes can be used as a floating static route. A floating static route must be configured with an administrative distance that is greater than the administrative distance of the dynamic routing protocol, because routes with smaller administrative distances are preferred.

Note By default, static routes have smaller administrative distances than dynamic routes, so static routes will be used in preference to dynamic routes.

How to Implement Static Routes for IPv6

•Configuring a Static IPv6 Route (required)

•Configuring a Floating Static IPv6 Route (optional)

•Verifying Static IPv6 Route Configuration and Operation (optional)

Configuring a Static IPv6 Route

SUMMARY STEPS

1. enable

2. configure terminal

3. ipv6 route ipv6-prefix/prefix-length {ipv6-address | interface-type interface-number [ipv6-address]} [administrative-distance] [administrative-multicast-distance | unicast | multicast] [tag tag]

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

ipv6 route ipv6-prefix/prefix-length {ipv6-address | interface-type interface-number [ipv6-address]} [administrative-distance] [administrative-multicast-distance | unicast | multicast] [tag tag]
Example:

Router(config)# ipv6 route ::/0 serial 2/0/0

Configures a static IPv6 route.

•A static default IPv6 route is being configured on a serial interface.

•See the syntax examples that immediately follow this table for specific uses of the ipv6 route command for configuring static routes.

•Refer to the ipv6 route command entry in the Cisco IOS IPv6 Command Reference for more details on the arguments and keywords used in this command.

Configuring a Floating Static IPv6 Route

SUMMARY STEPS

1. enable

2. configure terminal

3. ipv6 route ipv6-prefix/prefix-length {ipv6-address | interface-type interface-number [ipv6-address]} [administrative-distance] [administrative-multicast-distance | unicast | multicast] [tag tag]

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

ipv6 route ipv6-prefix/prefix-length {ipv6-address | interface-type interface-number [ipv6-address]} [administrative-distance] [administrative-multicast-distance | unicast | multicast] [tag tag]
Example:

Router(config)# ipv6 route 2001:DB8::/32 serial 2/0 201

Configures a static IPv6 route.

•In this example, a floating static IPv6 route is being configured. An administrative distance of 200 is configured.

•Default administrative distances are as follows:

–Connected interface—0

–Static route—1

–Enhanced Interior Gateway Routing Protocol (EIGRP) summary route—5

–External Border Gateway Protocol (eBGP)—20

–Internal Enhanced IGRP—90

–IGRP—100

–Open Shortest Path First—110

–Intermediate System-to-Intermediate System (IS-IS)—115

–Routing Information Protocol (RIP)—120

–Exterior Gateway Protocol (EGP)—140

–EIGRP external route—170

–Internal BGP—200

–Unknown—255

Verifying Static IPv6 Route Configuration and Operation

SUMMARY STEPS

1. enable

2. show ipv6 static [ipv6-address | ipv6-prefix/prefix-length][interface interface-type interface-number] [recursive] [detail]

or

show ipv6 route [ipv6-address | ipv6-prefix/prefix-length | protocol | interface-type interface-number]

3. debug ipv6 routing

DETAILED STEPS
Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.
Step 2
show ipv6 static [ipv6-address | ipv6-prefix/prefix-length][interface interface-type interface-number] [recursive] [detail]
or

show ipv6 route [ipv6-address | ipv6-prefix/prefix-length | protocol | interface-type interface-number]
Example:

Router# show ipv6 static
or

Example:

Router# show ipv6 route static
Displays the current contents of the IPv6 routing table.

•These examples show two different ways of displaying IPv6 static routes.

•Refer to the show ipv6 static and show ipv6 route command entries in the Cisco IOS IPv6 Command Reference for more details on the arguments and keywords used in this command.
Step 3

debug ipv6 routing
Example:

Router# debug ipv6 routing

Displays debugging messages for IPv6 routing table updates and route cache updates.
Examples

•Sample Output from the ipv6 route Command

•Sample Output from the show ipv6 static Command When No Options Are Specified in the Command Syntax

•Sample Output from the show ipv6 static Command with the IPv6 Address and Prefix Command

•Sample Output from the show ipv6 static interface Command

•Sample Output from the show ipv6 static recursive Command

•Sample Output from the show ipv6 static detail Command

•Sample Output from the show ipv6 route Command

•Sample Output from the debug ipv6 routing Command

Sample Output from the ipv6 route Command

In addition to the syntax example included in the "DETAILED STEPS" section, the following syntax examples illustrate use of the ipv6 route for configuring the various types of static routes.

The following example shows how to configure a directly attached static route through a point-to-point interface.
Router(config)# ipv6 route 2001:DB8::/32 serial 0/0/0
The following example shows how to configure a directly attached static route on a broadcast interface.
Router(config)# ipv6 route 2001:DB8::1/32 gigabitethernet1/0/0 
The following example shows how to configure a fully specified static route on a broadcast interface.
Router(config)# ipv6 route 2001:DB8::1/32 gigabitethernet1/0/0 fe80::1
In the following example, a static route is being configured to a specified next-hop address, from which the output interface is automatically derived.
Router(config)# ipv6 route 2001:DB8::/32 2001:DB8:2002:1
Sample Output from the show ipv6 static Command When No Options Are Specified in the Command Syntax

When no options are specified in the command, those routes installed in the IPv6 routing table are marked with an asterisk, as shown in the following example:
Router# show ipv6 static
IPv6 Static routes
Code: * - installed in RIB
* 2001:DB8:3000:0/16, interface GigabitEthernet1/0/0, distance 1
* 2001:DB8:4000:0/16, via nexthop 2001:DB8:1:1, distance 1
  2001:DB8:5000:0/16, interface GigabitEthernet3/0/0, distance 1
* 2001:DB8:5555:0/16, via nexthop 2001:DB8:4000:1, distance 1
  2001:DB8:5555:0/16, via nexthop 2001:DB8:9999:1, distance 1
* 2001:DB8:5555:0/16, interface GigabitEthernet2/0/0, distance 1
* 2001:DB8:6000:0/16, via nexthop 2001:DB8:2007:1, interface GigabitEthernet1/0/0, 
distance 1
Sample Output from the show ipv6 static Command with the IPv6 Address and Prefix Command

When the ipv6-address or ipv6-prefix/prefix-length argument is specified, only information about static routes for that address or network is displayed. The following is sample output from the show ipv6 static command when entered with the IPv6 prefix 2001:DB8:200::/35:
Router# show ipv6 static 2001:DB8:5555:0/16
IPv6 Static routes
Code: * - installed in RIB
* 2001:DB8:5555:0/16, via nexthop 2001:DB8:4000:1, distance 1
  2001:DB8:5555:0/16, via nexthop 2001:9999:1, distance 2
* 2001:DB8:5555:0/16, interface GigabitEthernet2/0/0, distance 1
Sample Output from the show ipv6 static interface Command

When an interface is supplied, only those static routes with the specified interface as outgoing interface are displayed. The interface keyword may be used with or without the IPv6 address and prefix specified in the show ipv6 static command.
Router# show ipv6 static interface gigabitethernet3/0/0
IPv6 Static routes
Code: * - installed in RIB
  2001:DB8:5000:)/16, interface GigabitEthernet3/0/0, distance 1
Sample Output from the show ipv6 static recursive Command

When the recursive keyword is specified in the show ipv6 static command, only recursive static routes are displayed. The recursive keyword is mutually exclusive with the interface keyword, but it may be used with or without the IPv6 prefix included in the command syntax.
Router# show ipv6 static recursive
IPv6 Static routes
Code: * - installed in RIB
* 2001:DB8:4000:0/16, via nexthop 2001:DB8:1:1, distance 1
* 2001:DB8:5555:0/16, via nexthop 2001:DB8:4000:1, distance 2
  2001:DB8:5555:0/16, via nexthop 2001:DB8:9999:1, distance 3
Sample Output from the show ipv6 static detail Command

When the detail keyword is specified, the following additional information is also displayed:

•For valid recursive routes, the output path set, and maximum resolution depth

•For invalid recursive routes, the reason why the route is not valid.

•For invalid direct or fully-specified routes, the reason why the route is not valid.
Router# show ipv6 static detail
IPv6 Static routes
Code: * - installed in RIB
* 2001:DB8:3000:0/16, interface GigabitEthernet1/0/0, distance 1
* 2001:DB8:4000:0/16, via nexthop 2001:DB8:2001:1, distance 1
     Resolves to 1 paths (max depth 1)
     via GigabitEthernet1/0/0
  2001:DB8:5000:0/16, interface GigabitEthernet3/0/0, distance 1
     Interface is down
* 2001:DB8:5555:0/16, via nexthop 2001:DB8:4000:1, distance 1
     Resolves to 1 paths (max depth 2)
     via GigabitEthernet1/0/0
  2001:DB8:5555:0/16, via nexthop 2001:DB8:9999:1, distance 1
     Route does not fully resolve
* 2001:DB8:5555:0/16, interface GigabitEthernet2/0/0, distance 1
* 2001:DB8:6000:0/16, via nexthop 2001:DB8:2007:1, interface GigabitEthernet1/0/0, 
distance 1
Sample Output from the show ipv6 route Command

In the following example, the show ipv6 route command is used to verify the configuration of a static route through a point-to-point interface:
Router# show ipv6 route
IPv6 Routing Table - 9 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
       U - Per-user Static route
       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea
       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
S   2001:DB8::/32 [1/0]
     via ::, Serial2/0
In the following example, the show ipv6 route command is used to verify the configuration of a static route on a multiaccess interface. An IPv6 link-local address—FE80::1—is the next-hop router.
Router# show ipv6 route
IPv6 Routing Table - 11 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
       U - Per-user Static route
       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea
       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
S   2001:DB8::/32 [1/0]
     via FE80::1, GigabitEthernet0/0/0
To display all static routes in the IPv6 routing table, use the show ipv6 route static command is used with static as the value of the protocol argument:
Router# show ipv6 route static
IPv6 Routing Table - 330 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
       U - Per-user Static route
       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea
S   2001:DB8::/32 [1/0]
     via ::, Tunnel0
S   3FFE:C00:8011::/48 [1/0]
     via ::, Null0
S   ::/0 [254/0]
     via 2001:DB8:2002:806B, Null
Sample Output from the debug ipv6 routing Command

In the following example, the debug ipv6 routing command is used to verify the installation of a floating static route into the IPv6 routing table when an IPv6 RIP route is deleted. The floating static IPv6 route was previously configured with an administrative distance value of 130. The backup route was added as a floating static route because RIP routes have a default administrative distance of 120, and the RIP route should be the preferred route. When the RIP route is deleted, the floating static route is installed in the IPv6 routing table.
Router# debug ipv6 routing
*Oct 10 18:28:00.847: IPv6RT0: rip two, Delete 2001:DB8::/32 from table
*Oct 10 18:28:00.847: IPv6RT0: static, Backup call for 2001:DB8::/32
*Oct 10 18:28:00.847: IPv6RT0: static, Add 2001:DB8::/32 to table
*Oct 10 18:28:00.847: IPv6RT0: static, Adding next-hop :: over Serial2/0 for 
2001:DB8::/32, [130/0]
Configuration Examples for Implementing Static Routes for IPv6

Static routes may be used for a variety of purposes. Common usages include the following:

•Manual summarization

•Traffic discard

•Fixed default route

•Backup route

In many cases, alternative mechanisms exist within Cisco IOS XE software to achieve the same objective. Whether to use static routes or one of the alternative mechanisms depends on local circumstances.

This section provides the following configuration examples:

•Example: Configuring Manual Summarization

•Example: Configuring Traffic Discard

•Example: Configuring a Fixed Default Route

•Example: Configuring a Floating Static Route

Example: Configuring Manual Summarization

The following example shows a static route being used to summarize local interface prefixes advertised into RIP. The static route also serves as a discard route, discarding any packets received by the router to a 2001:DB8:1::/48 destination not covered by a more specific interface prefix.
Router> enable
Router# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)# interface gigabitethernet0/0/0
Router(config-if)# ipv6 address 2001:DB8:2:1234/64
Router(config-if)# exit
Router(config)# 
Router(config)# interface gigabitethernet1/0/0
Router(config-if)# ipv6 address 2001:DB8:3:1234/64
Router(config-if)# exit
Router(config)#
Router(config)# interface gigabitethernet2/0/0
Router(config-if)# ipv6 address 2001:DB8:4:1234/64
Router(config-if)# exit
Router(config)#
Router(config)# interface gigabitethernet3/0/0
Router(config-if)# ipv6 address 2001:DB8::1234/64
Router(config-if)# ipv6 rip one enable
Router(config-if)# exit
Router(config)#
Router(config)# ipv6 router rip one
Router(config-rtr)# redistribute static
Router(config-rtr)# exit
Router(config)#
Router(config)# ipv6 route 2001:DB8:1:1/48 null0
Router(config)# end
Router#
00:01:30: %SYS-5-CONFIG_I: Configured from console by console
Router# show ipv6 route static
IPv6 Routing Table - 3 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
       U - Per-user Static route
       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
       ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
S   2001:DB8:1::/48 [1/0]
     via ::, Null0
Example: Configuring Traffic Discard

Configuring a static route to point at interface null0 may be used for discarding traffic to a particular prefix. For example, if it is required to discard all traffic to prefix 2001:DB8:42:1/64, the following static route would be defined:
Router> enable
Router# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)# ipv6 route 2001:DB8:42:1::/64 null0 
Router(config)# end
Router#
00:05:44: %SYS-5-CONFIG_I: Configured from console by console
Example: Configuring a Fixed Default Route

A default static route is often used in simple router topologies. In the following example, a router is connected to its local site via GigabitEthernet 0/0/0 and to the main corporate network via Serial 2/0/0 and Serial 3/0/0. All nonlocal traffic will be routed over the two serial interfaces.
Router(config)# interface gigabitethernet0/0/0
Router(config-if)# ipv6 address 2001:DB8:17:1234/64
Router(config-if)# exit
Router(config)# interface Serial2/0/0
Router(config-if)# ipv6 address 2001:DB8:1:1234/64
Router(config-if)# exit
Router(config)# interface Serial3/0/0
Router(config-if)# ipv6 address 2001:DB8:2:124/64
Router(config-if)# exit
Router(config)# ipv6 route ::/0 Serial2/0
Router(config)# ipv6 route ::/0 Serial3/0
Router(config)# end
Router#
00:06:30: %SYS-5-CONFIG_I: Configured from console by console
Router# show ipv6 route static
IPv6 Routing Table - 7 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
       U - Per-user Static route
       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
       ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
S   ::/0 [1/0]
     via ::, Serial2/0
     via ::, Serial3/0
Example: Configuring a Floating Static Route

A floating static route often is used to provide a backup path in the event of connectivity failure. In the following example, the router has connectivity to the network core via Serial2/0 and learns the route 2001:DB8:1:1/32 via IS-IS. If the Serial2/0/0 interface fails, or if route 2001:DB8:1:1/32 is no longer learned via IS-IS (indicating loss of connectivity elsewhere in the network), traffic is routed via the backup ISDN interface.
Router> enable
Router# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)# interface gigabitethernet0/0/0
Router(config-if)# ipv6 address 2001:DB8:17:1234/64
Router(config-if)# exit
Router(config)# interface Serial2/0/0
Router(config-if)# ipv6 address 2001:DB8:1:1234/64
Router(config-if)# ipv6 router isis
Router(config-if)# exit
Router(config)# router isis
Router(config-router)# net 42.0000.0000.0000.0001.00
Router(config-router)# exit
Router(config)# interface BRI1/0
Router(config-if)# encapsulation ppp
Router(config-if)# ipv6 enable
Router(config-if)# isdn switch-type basic-net3
Router(config-if)# ppp authentication chap optional
Router(config-if)# ppp multilink
Router(config-if)# exit
Router(config)# dialer-list 1 protocol ipv6 permit
Router(config)# ipv6 route 2001:DB8:1::/32 BRI1/0 200
Router(config)# end
Router#
00:03:07: %SYS-5-CONFIG_I: Configured from console by console
Where to Go Next

If you want to implement routing protocols, refer to the Implementing RIP for IPv6, Implementing IS-IS for IPv6, Implementing OSPF for IPv6, or Implementing Multiprotocol BGP for IPv6 module.

Additional References

Related Documents

Related Topic

Document Title

IP static route configuration

"Configuring IP Routing Protocol-Independent Features," Cisco IOS XE IP Routing Protocols Configuration Guide, Release 2

IP static route commands: complete command syntax, command mode, defaults, usage guidelines, and examples

Cisco IOS IP Routing Protocols Command Reference

IPv6 supported feature list

"Start Here: Cisco IOS XE Software Release Specifics for IPv6 Features," Cisco IOS XE IPv6 Configuration Guide, Release 2

IPv6 commands: complete command syntax, command mode, defaults, usage guidelines, and examples

Cisco IOS IPv6 Command Reference

Cisco IOS master command list, all releases

Cisco IOS Master Command List, All Releases

Standards

Standards

Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

—

MIBs

MIBs

MIBs Link

None

To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

RFCs

RFCs

Title

No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.

—

Technical Assistance

Description

Link

The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html

Feature Information for Implementing Static Routes for IPv6

Table 13 lists the features in this module and provides links to specific configuration information.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Note Table 13 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Table 13 Feature Information for Implementing Static Routes for IPv6

Feature Name

Releases

Feature Information

IPv6 Routing—Static Routing

Cisco IOS XE Release 2.1

Static routes are manually configured and define an explicit path between two networking devices.

This entire document provides information about this feature.

The following commands were modified by this feature: debug ipv6 route, ipv6 route, ipv6 route static bfd, monitor event ipv6 static, show ipv6 route, show ipv6 route summary, show ipv6 static

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

© 2001-2011 Cisco Systems, Inc. All rights reserved.