Guest

Networking Software (IOS & NX-OS)

PBR Recursive Next Hop

Hierarchical Navigation

Downloads

Table Of Contents

PBR Recursive Next Hop

Finding Feature Information

Contents

How to Configure PBR Recursive Next Hop

Setting the Recursive Next-Hop IP Address

Prerequisites

Restrictions

Verifying the Recursive Next-Hop Configuration

Configuration Examples for PBR Recursive Next Hop

Recursive Next-Hop IP Address: Example

Additional References

Related Documents

MIBs

Technical Assistance

Feature Information for PBR Recursive Next Hop


PBR Recursive Next Hop

First Published: 2003
Last Updated: May 4, 2009

The PBR Recursive Next Hop feature enhances route maps to enable configuration of a recursive next-hop IP address that is used by policy-based routing (PBR). The recursive next-hop IP address is installed in the routing table and can be a subnet that is not directly connected. If the recursive next-hop IP address is not available, packets are routed using a default route.

Because Cisco Express Forwarding (CEF) or process switching provides the infrastructure, the benefit of this feature is the CEF loadsharing.

Finding Feature Information

For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for PBR Recursive Next Hop" section.

Use Cisco Feature Navigator to find information about platform support and Cisco IOS XE software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

•How to Configure PBR Recursive Next Hop

•Configuration Examples for PBR Recursive Next Hop

•Additional References

•Feature Information for PBR Recursive Next Hop

How to Configure PBR Recursive Next Hop

This section contains the following procedures:

•Setting the Recursive Next-Hop IP Address (required)

•Verifying the Recursive Next-Hop Configuration (optional)

Setting the Recursive Next-Hop IP Address

The infrastructure provided by CEF or process switching performs the recursion to the next-hop IP address. The configuration sequence, which affects routing, is as follows:

1. Next-hop

2. Next-hop recursive

3. Interface

4. Default next-hop

5. Default interface

If both a next-hop address and a recursive next-hop IP address are present in the same route-map entry, the next hop is used. If the next hop is not available, the recursive next hop is used. If the recursive next hop is not available and no other IP address is present, the packet is routed using the default routing table; it is not dropped. If the packet is supposed to be dropped, use the set ip next-hop command with the recursive keyword, followed by a set interface null0 configuration.

Perform this task to set the IP address for the recursive next-hop router.

Prerequisites

If loadsharing is required, CEF loadsharing should be configured for per-packet or per-destination loadsharing. Loadbalancing should be done over all equal-cost routes to the subnet that has been configured by the set ip next-hop recursive command.

This functionality should be available in centralized and distributed systems.

Restrictions

Only one recursive next-hop IP address is supported per route-map entry.

SUMMARY STEPS

1. enable

2. configure terminal

3. access-list access-list-number {deny | permit} source [source-wildcard] [log]

4. route-map map-tag

5. set ip next-hop ip-address

6. set ip next-hop {ip-address [...ip-address] | recursive ip-address}

7. match ip address access-list-number

8. end

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

access-list access-list-number {deny | permit} source [source-wildcard] [log]

Example:

Router(config)# access-list 101 permit 10.60.0.0 0.0.255.255

Configures an access list. The example configuration permits any source IP address that falls within the 10.60.0.0. 0.0.255.255 subnet.

Step 4 

route-map map-tag

Example:

Router(config)# route-map abccomp

Enables policy routing and enters route-map configuration mode.

Step 5 

set ip next-hop ip-address

Example:

Router(config-route-map)# set ip next-hop 10.10.1.1

Sets a next-hop router IP address.

Note Set this IP address separately from the next-hop recursive router configuration.

Step 6 

set ip next-hop {ip-address [...ip-address] | recursive ip-address}

Example:

Router(config-route-map)# set ip next-hop recursive 10.20.3.3

Sets a recursive next-hop IP address.

Note This configuration does not ensure that packets get routed using the recursive IP address if an intermediate IP address is a shorter route to the destination.

Step 7 

match ip address access-list-number

Example:

Router(config-route-map)# match ip address 101

Sets an access list to be matched.

Step 8 

end

Example:

Router(config-route-map)# end

Exits route-map configuration mode and returns to privileged EXEC mode.

Verifying the Recursive Next-Hop Configuration

To verify the recursive next-hop configuration, perform the following steps.

SUMMARY STEPS

1. show running-config | begin abccomp

2. show route-map map-name

DETAILED STEPS

Step 1 show running-config | begin abccomp

Use this command to verify the IP addresses for a next-hop and recursive next-hop IP address, for example: 

Router# show running-config | begin abccomp


route-map abccomp permit 10

 match ip address 101 ! Defines the match criteria for an access list.

 set ip next-hop recursive 10.3.3.3 ! If the match criteria are met, the recursive IP 
 address is set.

 set ip next-hop 10.1.1.1 10.2.2.2 10.4.4.4

Step 2 show route-map map-name

Use this command to display the route maps, for example: 

Router# show route-map abccomp


route-map abccomp, permit, sequence 10

 Match clauses:

  ip address (access-lists): 101 

 Set clauses:

  ip next-hop recursive 10.3.3.3

  ip next-hop 10.1.1.1 10.2.2.2 10.4.4.4

 Policy routing matches: 0 packets, 0 bytes

Configuration Examples for PBR Recursive Next Hop

This section provides the following configuration example:

•Recursive Next-Hop IP Address: Example

Recursive Next-Hop IP Address: Example

The following example shows the configuration of IP address 10.3.3.3 as the recursive next-hop router: 

route-map abccomp

 set ip next-hop 10.1.1.1

 set ip next-hop 10.2.2.2

 set ip next-hop recursive 10.3.3.3

 set ip next-hop 10.4.4.4

Additional References

The following sections provide references related to the PBR Recursive Next Hop feature.

Related Documents

Related Topic
Document Title

IP routing commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples

Cisco IOS IP Routing Protocols Command Reference

Cisco IOS master command list, all  releases

Cisco IOS Master Command List, All Releases


MIBs

MIBs
MIBs Link

No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

To locate and download MIBs for selected platforms, Cisco IOS XE software releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs


Technical Assistance

Description
Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/techsupport


Feature Information for PBR Recursive Next Hop

Table 1 lists the release history for this feature.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS XE software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Note Table 1 lists only the Cisco IOS XE software release that introduced support for a given feature in a given Cisco IOS XE software release train. Unless noted otherwise, subsequent releases of that Cisco IOS XE software release train also support that feature.

Table 1 Feature Information for PBR Recursive Next Hop 

Feature Name
Releases
Feature Information

PBR Recursive Next Hop

Cisco IOS XE Release 2.2

This feature was introduced on the Cisco ASR 1000 Series Aggregation Services Routers.

The following commands were modified by this feature: set ip next-hop, show route-map.


Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2003-2009 Cisco Systems, Inc. All rights reserved.