THIS DOCUMENTATION HAS BEEN MOVED
BGP Link Bandwidth
Download this chapter
BGP Link BandwidthBGP Link Bandwidth
 Feedback

Table Of Contents

BGP Link Bandwidth

Finding Feature Information

Contents

Prerequisites for BGP Link Bandwidth

Restrictions for BGP Link Bandwidth

Information About BGP Link Bandwidth

BGP Link Bandwidth Overview

Link Bandwidth Extended Community Attribute

Benefits of the BGP Link Bandwidth Feature

How to Configure BGP Link Bandwidth

Configuring BGP Link Bandwidth

Verifying BGP Link Bandwidth Configuration

Configuration Examples for BGP Link Bandwidth

BGP Link Bandwidth Configuration: Example

Verifying BGP Link Bandwidth

Additional References

Related Documents

Standards

MIBs

Technical Assistance

Feature Information for BGP Link Bandwidth


BGP Link Bandwidth

First Published: 2004
Last Updated: May 4, 2009

The Border Gateway Protocol (BGP) Link Bandwidth feature is used to advertise the bandwidth of an autonomous system exit link as an extended community. This feature is configured for links between directly connected external BGP (eBGP) neighbors. The link bandwidth extended community attribute is propagated to iBGP peers when extended community exchange is enabled. This feature is used with BGP multipath features to configure load balancing over links with unequal bandwidth.

Finding Feature Information

For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for BGP Link Bandwidth" section.

Use Cisco Feature Navigator to find information about platform support and Cisco IOS XE software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

•Prerequisites for BGP Link Bandwidth

•Restrictions for BGP Link Bandwidth

•Information About BGP Link Bandwidth

•How to Configure BGP Link Bandwidth

•Configuration Examples for BGP Link Bandwidth

•Additional References

•Feature Information for BGP Link Bandwidth

Prerequisites for BGP Link Bandwidth

•BGP load balancing or multipath load balancing must be configured before this feature is enabled.

•BGP extended community exchange must be enabled between iBGP neighbors to which the link bandwidth attribute is to be advertised.

•Cisco Express Forwarding or distributed Cisco Express Forwarding must be enabled on all participating routers.

Restrictions for BGP Link Bandwidth

•This feature can be configured only under IPv4 and VPNv4 address family sessions.

•BGP can originate the link bandwidth community only for directly connected links to eBGP neighbors.

•Both iBGP and eBGP load balancing are supported in IPv4 and VPNv4 address families. However, eiBGP load balancing is supported only in VPNv4 address family.

Information About BGP Link Bandwidth

To configure the BGP Link Bandwidth feature, you must understand the following concept:

•BGP Link Bandwidth Overview

•Link Bandwidth Extended Community Attribute

•Benefits of the BGP Link Bandwidth Feature

BGP Link Bandwidth Overview

The BGP Link Bandwidth feature used to enable multipath load balancing for external links with unequal bandwidth capacity. This feature is enabled under an IPv4 or VPNv4 address family sessions by entering the bgp dmzlink-bw command. This feature supports both iBGP, eBGP multipath load balancing, and eiBGP multipath load balancing in Multiprotocol Label Switching (MPLS) Virtual Private Networks (VPNs). When this feature is enabled, routes learned from directly connected external neighbor are propagated through the internal BGP (iBGP) network with the bandwidth of the source external link.

The link bandwidth extended community indicates the preference of an autonomous system exit link in terms of bandwidth. This extended community is applied to external links between directly connected eBGP peers by entering the neighbor dmzlink-bw command. The link bandwidth extended community attribute is propagated to iBGP peers when extended community exchange is enabled with the neighbor send-community command.

Link Bandwidth Extended Community Attribute

The link bandwidth extended community attribute is a 4-byte value that is configured for a link that on the demilitarized zone (DMZ) interface that connects two single hop eBGP peers. The link bandwidth extended community attribute is used as a traffic sharing value relative to other paths while forwarding traffic. Two paths are designated as equal for load balancing if the weight, local-pref, as-path length, Multi Exit Discriminator (MED), and Interior Gateway Protocol (IGP) costs are the same.

Benefits of the BGP Link Bandwidth Feature

The BGP Link Bandwidth feature allows BGP to be configured to send traffic over multiple iBGP or eBGP learned paths where the traffic that is sent is proportional to the bandwidth of the links that are used to exit the autonomous system. The configuration of this feature can be used with eBGP and iBGP multipath features to enable unequal cost load balancing over multiple links.

How to Configure BGP Link Bandwidth

This section contains the following procedures:

•Configuring BGP Link Bandwidth

•Verifying BGP Link Bandwidth Configuration

Configuring BGP Link Bandwidth

To configure the BGP Link Bandwidth feature, perform the steps in this section.

SUMMARY STEPS

1. enable

2. configure {terminal | memory | network}

3. router bgp autonomous-system-number

4. address-family ipv4 [mdt | multicast | tunnel | unicast [vrf vrf-name] | vrf vrf-name] | vpnv4 [unicast]

5. bgp dmzlink-bw

6. neighbor ip-address dmzlink-bw

7. neighbor ip-address send-community [both | extended | standard]

8. end

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables higher privilege levels, such as privileged EXEC mode.

•Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

router bgp autonomous-system-number

Example:

Router(config)# router bgp 50000

Enters router configuration mode to create or configure a BGP routing process.

Step 4 

address-family ipv4 [mdt | multicast | tunnel | unicast [vrf vrf-name] | vrf vrf-name] | vpnv4 [unicast]

Example:

Router(config-router)# address-family ipv4

Enters address family configuration mode.

•The BGP Link Bandwidth feature is supported only under the IPv4 and VPNv4 address families.

Step 5 

bgp dmzlink-bw

Example:

Router(config-router-af)# bgp dmzlink-bw

Configures BGP to distribute traffic proportionally to the bandwidth of the link.

•This command must be entered on each router that contains an external interface that is to be used for multipath load balancing.

Step 6 

neighbor ip-address dmzlink-bw

Example:

Router(config-router-af)# neighbor 172.16.1.1 dmzlink-bw

Configures BGP to include the link bandwidth attribute for routes learned from the external interface specified IP address.

•This command must be configured for each eBGP link that is to be configured as a multipath. Enabling this command allows the bandwidth of the external link to be propagated through the link bandwidth extended community.

Step 7 

neighbor ip-address send-community [both | extended | standard]

Example:

Router(config-router-af)# neighbor 10.10.10.1 send-community extended

(Optional) Enables community and/or extended community exchange with the specified neighbor.

•This command must be configured for iBGP peers to which the link bandwidth extended community attribute is to be propagated.

Step 8 

end

Example:

Router(config-router-af)# end

Exits address family configuration mode, and enters Privileged EXEC mode.

Verifying BGP Link Bandwidth Configuration

To verify the BGP Link Bandwidth feature, perform the steps in this section.

SUMMARY STEPS

1. enable

2. show ip bgp ip-address [longer-prefixes [injected] | shorter-prefixes [mask-length]]

3. show ip route [[ip-address [mask] [longer-prefixes]] | [protocol [process-id]] | [list access-list-number | access-list-name] | [static download]]

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables higher privilege levels, such as privileged EXEC mode.

•Enter your password if prompted.

Step 2 

show ip bgp ip-address [longer-prefixes [injected] | shorter-prefixes [mask-length]]

Example:

Router# show ip bgp 10.0.0.0

Displays information about the TCP and BGP connections to neighbors.

•The output displays the status of the link bandwidth configuration. The bandwidth of the link is shown in kilobytes.

Step 3 

show ip route [[ip-address [mask] [longer-prefixes]] | [protocol [process-id]] | [list access-list-number | access-list-name] | [static download]]

Example:

Router# show ip route 10.0.0.0

Displays the current state of the routing table.

•The output displays traffic share values, including the weights of the links that are used to direct traffic proportionally to the bandwidth of each link.

Configuration Examples for BGP Link Bandwidth

The following examples show how to configure and verify this feature:

•BGP Link Bandwidth Configuration: Example

•Verifying BGP Link Bandwidth

BGP Link Bandwidth Configuration: Example

In the following examples, the BGP Link Bandwidth feature is configured so BGP will distribute traffic proportionally to the bandwidth of each external link. Figure 1 shows two external autonomous systems connected by three links that each carry a different amount of bandwidth (unequal cost links). Multipath load balancing is enabled and traffic is balanced proportionally.

Figure 1 BGP Link Bandwidth Configuration

Router A Configuration

In the following example, Router A is configured to support iBGP multipath load balancing and to exchange the BGP extended community attribute with iBGP neighbors: 

Router A(config)# router bgp 100 

Router A(config-router)# neighbor 10.10.10.2 remote-as 100 

Router A(config-router)# neighbor 10.10.10.2 update-source Loopback 0 

Router A(config-router)# neighbor 10.10.10.3 remote-as 100 

Router A(config-router)# neighbor 10.10.10.3 update-source Loopback 0 

Router A(config-router)# address-family ipv4 

Router A(config-router)# bgp dmzlink-bw 

Router A(config-router-af)# neighbor 10.10.10.2 activate 

Router A(config-router-af)# neighbor 10.10.10.2 send-community both 

Router A(config-router-af)# neighbor 10.10.10.3 activate 

Router A(config-router-af)# neighbor 10.10.10.3 send-community both 

Router A(config-router-af)# maximum-paths ibgp 6

Router B Configuration

In the following example, Router B is configured to support multipath load balancing, to distribute Router D and Router E link traffic proportionally to the bandwidth of each link, and to advertise the bandwidth of these links to iBGP neighbors as an extended community: 

Router B(config)# router bgp 100 

Router B(config-router)# neighbor 10.10.10.1 remote-as 100 

Router B(config-router)# neighbor 10.10.10.1 update-source Loopback 0 

Router B(config-router)# neighbor 10.10.10.3 remote-as 100 

Router B(config-router)# neighbor 10.10.10.3 update-source Loopback 0 

Router B(config-router)# neighbor 172.16.1.1 remote-as 200 

Router B(config-router)# neighbor 172.16.1.1 ebgp-multihop 1 

Router B(config-router)# neighbor 172.16.2.2 remote-as 200 

Router B(config-router)# neighbor 172.16.2.2 ebgp-multihop 1 

Router B(config-router)# address-family ipv4 

Router B(config-router-af)# bgp dmzlink-bw 

Router B(config-router-af)# neighbor 10.10.10.1 activate 

Router B(config-router-af)# neighbor 10.10.10.1 next-hop-self 

Router B(config-router-af)# neighbor 10.10.10.1 send-community both 

Router B(config-router-af)# neighbor 10.10.10.3 activate 

Router B(config-router-af)# neighbor 10.10.10.3 next-hop-self 

Router B(config-router-af)# neighbor 10.10.10.3 send-community both 

Router B(config-router-af)# neighbor 172.16.1.1 activate 

Router B(config-router-af)# neighbor 172.16.1.1 dmzlink-bw 

Router B(config-router-af)# neighbor 172.16.2.2 activate 

Router B(config-router-af)# neighbor 172.16.2.2 dmzlink-bw

Router B(config-router-af)# maximum-paths ibgp 6

Router B(config-router-af)# maximum-paths 6

Router C Configuration

In the following example, Router C is configured to support multipath load balancing and to advertise the bandwidth of the link with Router E to iBGP neighbors as an extended community: 

Router C(config)# router bgp 100

Router C(config-router)# neighbor 10.10.10.1 remote-as 100

Router C(config-router)# neighbor 10.10.10.1 update-source Loopback 0

Router C(config-router)# neighbor 10.10.10.2 remote-as 100

Router C(config-router)# neighbor 10.10.10.2 update-source Loopback 0

Router C(config-router)# neighbor 172.16.3.30 remote-as 200

Router C(config-router)# neighbor 172.16.3.30 ebgp-multihop 1

Router C(config-router)# address-family ipv4 

Router C(config-router-af)# bgp dmzlink-bw 

Router C(config-router-af)# neighbor 10.10.10.1 activate

Router C(config-router-af)# neighbor 10.10.10.1 send-community both

Router C(config-router-af)# neighbor 10.10.10.1 next-hop-self

Router C(config-router-af)# neighbor 10.10.10.2 activate 

Router C(config-router-af)# neighbor 10.10.10.2 send-community both

Router C(config-router-af)# neighbor 10.10.10.2 next-hop-self 

Router C(config-router-af)# neighbor 172.16.3.3 activate 

Router C(config-router-af)# neighbor 172.16.3.3 dmzlink-bw 

Router C(config-router-af)# maximum-paths ibgp 6

Router C(config-router-af)# maximum-paths 6

Verifying BGP Link Bandwidth

The examples in this section show the verification of this feature on Router A and Router B.

Router B

In the following example, the show ip bgp command is entered on Router B to verify that two unequal cost best paths have been installed into the BGP routing table. The bandwidth for each link is displayed with each route. 

Router B# show ip bgp 192.168.1.0


BGP routing table entry for 192.168.1.0/24, version 48

Paths: (2 available, best #2)

Multipath: eBGP

  Advertised to update-groups:

     1          2

  200

    172.16.1.1 from 172.16.1.2 (192.168.1.1)

      Origin incomplete, metric 0, localpref 100, valid, external, multipath, best

      Extended Community: 0x0:0:0

      DMZ-Link Bw 278 kbytes

  200

    172.16.2.2 from 172.16.2.2 (192.168.1.1)

      Origin incomplete, metric 0, localpref 100, valid, external, multipath, best

      Extended Community: 0x0:0:0

      DMZ-Link Bw 625 kbytes

Router A

In the following example, the show ip bgp command is entered on Router A to verify that the link bandwidth extended community has been propagated through the iBGP network to Router A. The output shows that a route for each exit link (on Router B and Router C) to autonomous system 200 has been installed as a best path in the BGP routing table. 

Router A# show ip bgp 192.168.1.0


BGP routing table entry for 192.168.1.0/24, version 48

Paths: (3 available, best #3)

Multipath: eBGP

  Advertised to update-groups:

     1          2

  200

    172.16.1.1 from 172.16.1.2 (192.168.1.1)

      Origin incomplete, metric 0, localpref 100, valid, external, multipath

      Extended Community: 0x0:0:0

      DMZ-Link Bw 278 kbytes

  200

    172.16.2.2 from 172.16.2.2 (192.168.1.1)

      Origin incomplete, metric 0, localpref 100, valid, external, multipath, best

      Extended Community: 0x0:0:0

      DMZ-Link Bw 625 kbytes

  200

    172.16.3.3 from 172.16.3.3 (192.168.1.1)

      Origin incomplete, metric 0, localpref 100, valid, external, multipath, best

      Extended Community: 0x0:0:0

      DMZ-Link Bw 2500 kbytes

Router A

In the following example, the show ip route command is entered on Router A to verify the multipath routes that are advertised and the associated traffic share values: 

Router A# show ip route 192.168.1.0 


Routing entry for 192.168.1.0/24 

  Known via "bgp 100", distance 200, metric 0 

  Tag 200, type internal 

  Last update from 172.168.1.1 00:01:43 ago 

  Routing Descriptor Blocks: 

  * 172.168.1.1, from 172.168.1.1, 00:01:43 ago 

      Route metric is 0, traffic share count is 13 

      AS Hops 1, BGP network version 0 

      Route tag 200 

    172.168.2.2, from 172.168.2.2, 00:01:43 ago 

      Route metric is 0, traffic share count is 30 

      AS Hops 1, BGP network version 0 

      Route tag 200 

    172.168.3.3, from 172.168.3.3, 00:01:43 ago 

      Route metric is 0, traffic share count is 120 

      AS Hops 1, BGP network version 0 

      Route tag 200

Additional References

The following sections provide references related to the BGP Link Bandwidth feature.

Related Documents

Related Topic
Document Title

BGP commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples

Cisco IOS IP Routing: BGP Command Reference

BGP multipath load sharing for both eBGP and iBGP in an MPLS-VPN

BGP Multipath Load Sharing for Both eBGP and iBGP in an MPLS-VPN

iBGP multipath load sharing

iBGP Multipath Load Sharing

Cisco IOS master command list, all  releases

Cisco IOS Master Command List, All Releases


Standards

Standard
Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

—


MIBs

MIB
MIBs Link

No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

To locate and download MIBs for selected platforms, Cisco IOS XE software releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs


Technical Assistance

Description
Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/techsupport


Feature Information for BGP Link Bandwidth

Table 1 lists the release history for this feature.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS XE software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Note Table 1 lists only the Cisco IOS XE software release that introduced support for a given feature in a given Cisco IOS XE software release train. Unless noted otherwise, subsequent releases of that Cisco IOS XE software release train also support that feature.

Table 1 Feature Information for BGP Link Bandwidth 

Feature Name
Releases
Feature Information

BGP Link Bandwidth

Cisco IOS XE Release 2.1

This feature was introduced on the Cisco ASR 1000 Series Aggregation Services Routers.

The following commands were added or modified by this feature: bgp dmzlink-bw, neighbor dmzlink-bw.


Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2004-2009 Cisco Systems, Inc. All rights reserved.