Cisco IOS Flexible NetFlow Configuration Guide, Release 12.4T - Customizing Cisco IOS Flexible NetFlow Flow Records and Flow Monitors [Cisco IOS Software Releases 12.4 T]

Table Of Contents

Customizing Cisco IOS Flexible NetFlow Flow Records and Flow Monitors

Finding Feature Information

Contents

Prerequisites for Customizing Flexible NetFlow Flow Records and Flow Monitors

Information About Customizing Flexible NetFlow Flow Records and Flow Monitors

Identifying the Types of Traffic That You Want to Analyze

How to Customize Flexible NetFlow Flow Records and Flow Monitors

Configuring a Customized Flow Record

Configuring a Customized Flow Record for IPv4 Traffic

Configuring a Customized Flow Record for IPv6 Traffic

Verifying the Flow Record

Customizing a Flow Monitor

Flow Monitor

Prerequisites

Restrictions

Verifying the Flow Monitor

Applying a Flow Monitor to an Interface

Restrictions

Verifying That Flexible NetFlow Is Enabled

Viewing the Flow Monitor Cache

Prerequisites

Configuration Examples for Customizing Flexible NetFlow Flow Records and Flow Monitors

Configuring a Permanent Flow Record Cache with a Limited Number of Possible Flows: Example

Configuring a Customized Flow Record Cache for Monitoring IPv6 Traffic: Example

Configuring Flexible NetFlow for Monitoring MAC and VLAN Statistics: Example

Configuring Flexible NetFlow for Ingress VRF Support: Example

Configuring Flexible NetFlow for Network Based Application Recognition (NBAR) : Example

Where to Go Next

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Feature Information for Flexible NetFlow

Customizing Cisco IOS Flexible NetFlow Flow Records and Flow Monitors

First Published: June 19, 2006

Last Updated: November 20, 2009

This document contains information about and instructions for customizing Flexible NetFlow flow records and flow monitor requirements. If the tasks and configuration examples in the "Getting Started with Configuring Cisco IOS Flexible NetFlow" module and the "Configuring Cisco IOS Flexible NetFlow with Predefined Records" module were not suitable for your traffic analysis requirements, you can use the information and instructions in this document to customize Flexible NetFlow to meet your traffic analysis requirements.

NetFlow is a Cisco IOS technology that provides statistics on packets flowing through a router. NetFlow is the standard for acquiring IP operational data from IP networks. NetFlow provides network and security monitoring, network planning, traffic analysis, and IP accounting.

Flexible NetFlow improves on original NetFlow by adding the capability to customize the traffic analysis parameters for your specific requirements. Flexible NetFlow makes it easier to create more complex configurations for traffic analysis and data export through the use of reusable configuration components.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for Flexible NetFlow" section.

Use Cisco Feature Navigator to find information about platform support and Cisco IOS, Catalyst OS, and Cisco IOS XE software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Contents

•Prerequisites for Customizing Flexible NetFlow Flow Records and Flow Monitors

•Information About Customizing Flexible NetFlow Flow Records and Flow Monitors

•How to Customize Flexible NetFlow Flow Records and Flow Monitors

•Configuration Examples for Customizing Flexible NetFlow Flow Records and Flow Monitors

•Where to Go Next

•Additional References

•Feature Information for Flexible NetFlow

Prerequisites for Customizing Flexible NetFlow Flow Records and Flow Monitors

The following prerequisites must be met before you can configure Flexible NetFlow:

•You are familiar with the information in the "Cisco IOS Flexible NetFlow Overview" module.

•You are familiar with the Flexible NetFlow key fields as they are defined in the following commands in the Cisco IOS Flexible NetFlow Command Reference:

–match flow

–match interface

–match {ipv4 | ipv6}

–match routing

–match transport

•You are familiar with the Flexible NetFlow non-key fields as they are defined in the following commands in the Cisco IOS Flexible NetFlow Command Reference:

–collect counter

–collect flow

–collect interface

–collect {ipv4 | ipv6}

–collect routing

–collect timestamp sys-uptime

–collect transport

•The networking device must be running a Cisco IOS release that supports Flexible NetFlow. See the "Cisco IOS Flexible NetFlow Features Roadmap" module for a list of Cisco IOS software releases that support Flexible NetFlow.

IPv4 Traffic

•The networking device must be configured for IPv4 routing.

•One of the following must be enabled on your router and on any interfaces on which you want to enable Flexible NetFlow: Cisco Express Forwarding (CEF) or distributed CEF (dCEF).

IPv6 Traffic

•The networking device must be configured for IPv6 routing.

•One of the following must be enabled on your router and on any interfaces on which you want to enable Flexible NetFlow: Cisco Express Forwarding IPv6 (CEF IPv6) or distributed CEF IPv6 (dCEF IPv6).

Information About Customizing Flexible NetFlow Flow Records and Flow Monitors

Before you customize Flexible NetFlow flow records and flow monitors, you must understand the following concept:

•Identifying the Types of Traffic That You Want to Analyze

Identifying the Types of Traffic That You Want to Analyze

If the predefined Flexible NetFlow records are not suitable for your traffic requirements, you can create a user-defined (custom) record using the Flexible NetFlow collect and match commands. Before you can create a customized record, you must decide the criteria that you are going to use for the key and non-key fields.

If you want to create a customized record for detecting network attacks, you must include the appropriate key and non-key fields in the record to ensure that the router creates the flows and captures the data that you need to analyze the attack and respond to it. For example, SYN flood attacks are a common denial of service (DoS) attack in which TCP flags are used to flood open TCP requests to a destination host. When a normal TCP connection starts, a destination host receives a SYN (synchronize/start) packet from a source host and sends back a SYN ACK (synchronize acknowledge). The destination host must then hear an ACK (acknowledge) of the SYN ACK before the connection is established. This is referred to as the "TCP three-way handshake." While waiting for the ACK to the SYN ACK, a connection queue of finite size on the destination host keeps track of connections waiting to be completed. This queue typically empties quickly since the ACK is expected to arrive a few milliseconds after the SYN ACK. The TCP SYN attack exploits this design by having an attacking source host generate TCP SYN packets with random source addresses toward a victim host. The victim destination host sends a SYN ACK back to the random source address and adds an entry to the connection queue. Since the SYN ACK is destined for an incorrect or non-existent host, the last part of the "three-way handshake" is never completed and the entry remains in the connection queue until a timer expires, typically for about one minute. By generating phony TCP SYN packets from random IP addresses at a rapid rate, it is possible to fill up the connection queue and deny TCP services (such as e-mail, file transfer, or WWW) to legitimate users.

The information needed for a security monitoring record for this type of DoS attack might include the following key and non-key fields:

•Key fields:

–Destination IP address or destination IP subnet

–TCP flags

–Packet count

•Non-key fields

–Destination IP address

–Source IP address

–Interface input and output

Tip Many users configure a general Flexible NetFlow monitor that triggers a more detailed Flexible NetFlow view of a DoS attack using these key and non-key fields.

How to Customize Flexible NetFlow Flow Records and Flow Monitors

The tasks in this section explain how to do the following:

•Customize a Flexible NetFlow flow record.

•Customize a Flexible NetFlow flow monitor.

•Enable Flexible NetFlow.

Note Only the keywords and arguments required for the Flexible NetFlow commands used in these tasks are explained in these tasks. For information about the other keywords and arguments available for these Flexible NetFlow commands, refer to the Cisco IOS Flexible NetFlow Command Reference.

To customize Flexible NetFlow flow records and flow monitors, and to enable Flexible NetFlow, perform the following tasks:

•Configuring a Customized Flow Record

•Verifying the Flow Record (optional)

•Customizing a Flow Monitor

•Verifying the Flow Monitor (optional)

•Applying a Flow Monitor to an Interface

•Verifying That Flexible NetFlow Is Enabled (optional)

•Viewing the Flow Monitor Cache (optional)

Configuring a Customized Flow Record

Customized flow records are used to analyze traffic data for a specific purpose. A customized flow record must have at least one match criterion for use as the key field and typically has at least one collect criterion for use as a non-key field.

There are hundreds of possible permutations of customized flow records. This task explains the steps that are used to create one of the possible permutations. Modify the steps in these tasks as appropriate to create a customized flow record for your requirements.

To configure a customized flow record, perform either of the following tasks:

•Configuring a Customized Flow Record for IPv4 Traffic

•Configuring a Customized Flow Record for IPv6 Traffic

Configuring a Customized Flow Record for IPv4 Traffic

SUMMARY STEPS

1. enable

2. configure terminal

3. flow record flow-record-name

4. description string

5. match ipv4 {destination | source} address

6. Repeat Step 5 as required to configure additional key fields for the record.

7. collect ipv4 source {address | mask [minimum-mask mask] | prefix [minimum-mask mask]}

8. Repeat Step 7 as required to configure additional non-key fields for the record

9. end

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

flow record flow-record-name
Example:

Router(config)# flow record FLOW-RECORD-1

Creates a flow record and enters flow record configuration mode.

•This command also allows you to modify an existing flow record.

Step 4

description string
Example:

Router(config-flow-record)# description Used for basic traffic analysis

(Optional) Creates a description for the flow record.

Step 5

match ipv4 {destination | source} address
Example:

Router(config-flow-record)# match ipv4 destination address

Configures a key field for the flow record.

Note This example configures the IPv4 destination address as a key field for the record. For information about the other key fields available for the match ipv4 command, and the other match commands that are available to configure key fields, refer to the Cisco IOS Flexible NetFlow Command Reference.

Step 6

Repeat Step 5 as required to configure additional key fields for the record.

—

Step 7

collect ipv4 source {address | mask [minimum-mask mask] | prefix [minimum-mask mask]}
Example:

Router(config-flow-record)# collect ipv4 source address

Configures one or more of the IPv4 source fields in the flow as a non-key field for the record.

Note This example configures the IPv4 source address as a non-key field for the record. For information on the other collect commands that are available to configure non-key fields, refer to the Cisco IOS Flexible NetFlow Command Reference.

Step 8

Repeat Step 7 as required to configure additional non-key fields for the record.

—

Step 9

end
Example:

Router(config-flow-record)# end

Exits flow record configuration mode and returns to privileged EXEC mode.

Configuring a Customized Flow Record for IPv6 Traffic

SUMMARY STEPS

1. enable

2. configure terminal

3. flow record flow-record-name

4. description string

5. match ipv6 {destination | source} address

6. Repeat Step 5 as required to configure additional key fields for the record.

7. collect ipv6 source {address | mask [minimum-mask mask] | prefix [minimum-mask mask]}

8. Repeat Step 7 as required to configure additional non-key fields for the record

9. end

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

flow record flow-record-name
Example:

Router(config)# flow record FLOW-RECORD-2

Creates a flow record and enters flow record configuration mode.

•This command also allows you to modify an existing flow record.

Step 4

description string
Example:

Router(config-flow-record)# description Used for basic IPv6 traffic analysis

(Optional) Creates a description for the flow record.

Step 5

match ipv6 {destination | source} address
Example:

Router(config-flow-record)# match ipv6 destination address

Configures a key field for the flow record.

Note This example configures the IPv6 destination address as a key field for the record. For information about the other key fields available for the match ipv6 command, and the other match commands that are available to configure key fields, refer to the Cisco IOS Flexible NetFlow Command Reference.

Step 6

Repeat Step 5 as required to configure additional key fields for the record.

—

Step 7

collect ipv6 source {address | mask [minimum-mask mask] | prefix [minimum-mask mask]}
Example:

Router(config-flow-record)# collect ipv6 source address

Configures the number of packets in the flow as a non-key field for the record.

Note This example configures the IPv6 source address as a non-key field for the record. For information about the other collect commands that are available to configure non-key fields, refer to the Cisco IOS Flexible NetFlow Command Reference.

Step 8

Repeat Step 7 as required to configure additional non-key fields for the record.

—

Step 9

end
Example:

Router(config-flow-record)# end

Exits flow record configuration mode and returns to privileged EXEC mode.

Verifying the Flow Record

To view the current status of a flow record and verify the configuration commands that you entered, perform the following optional task.

SUMMARY STEPS

1. enable

2. show flow record

3. show running-config flow record

DETAILED STEPS

Step 1 enable

The enable command enters privileged EXEC mode (enter the password if prompted).
Router> enable
Router#
Step 2 show flow record

The show flow record command shows the current status of the flow monitor that you specify.
Router# show flow record
flow record FLOW-RECORD-2:
  Description:        Used for basic IPv6 traffic analysis
  No. of users:       1
  Total field space:  53 bytes
  Fields:
    match ipv6 destination address
    collect ipv6 protocol
    collect ipv6 source address
    collect transport source-port
    collect transport destination-port
    collect counter bytes
    collect counter packets
    collect timestamp sys-uptime first
    collect timestamp sys-uptime last
flow record FLOW-RECORD-1:
  Description:        Used for basic IPv4 traffic analysis
  No. of users:       1
  Total field space:  29 bytes
  Fields:
    match ipv4 destination address
    collect ipv4 protocol
    collect ipv4 source address
    collect transport source-port
    collect transport destination-port
    collect counter bytes
    collect counter packets
    collect timestamp sys-uptime first
    collect timestamp sys-uptime last
Step 3 show running-config flow record

The show running-config flow record command shows the configuration commands of the flow monitor that you specify.
Router# show running-config flow record
Current configuration:
!
flow record FLOW-RECORD-2
 description Used for basic IPv6 traffic analysis
 match ipv6 destination address
 collect ipv6 protocol
 collect ipv6 source address
 collect transport source-port
 collect transport destination-port
 collect counter bytes
 collect counter packets
 collect timestamp sys-uptime first
 collect timestamp sys-uptime last
!
!
flow record FLOW-RECORD-1
 description Used for basic IPv4 traffic analysis
 match ipv4 destination address
 collect ipv4 protocol
 collect ipv4 source address
 collect transport source-port
 collect transport destination-port
 collect counter bytes
 collect counter packets
 collect timestamp sys-uptime first
 collect timestamp sys-uptime last
!
Customizing a Flow Monitor

To create a customized flow monitor, perform the following required task.

Flow Monitor

Each flow monitor has a separate cache assigned to it. Each flow monitor requires a record to define the contents and layout of its cache entries. These record formats can be one of the predefined formats, or an advanced user can create a customized format using the flow record command. This task uses the record that you created in the "Configuring a Customized Flow Record" section.

Prerequisites

If you want to use a customized record instead of using one of the Flexible NetFlow predefined records, you must create the customized record before you can perform this task. Refer to the "Configuring a Customized Flow Record" section for information about and instructions for creating a customized flow record.

If you want to add a flow exporter to the flow monitor for data export, you must create the exporter before you can complete this task. Refer to the "Configuring Data Export for Cisco IOS Flexible NetFlow with Flow Exporters" module for information about and instructions for creating a flow exporter.

Restrictions

You must use the no ip flow monitor command to remove a flow monitor from all of the interfaces to which you have applied it before you can modify the parameters for the record command on the flow monitor. For information about the ip flow monitor command, refer to the Cisco IOS Flexible NetFlow Command Reference.

SUMMARY STEPS

1. enable

2. configure terminal

3. flow monitor monitor-name

4. description string

5. record {record-name | netflow-original | netflow {ipv4 | ipv6} record [peer]}

6. cache {entries entries | timeout {active active | inactive inactive | update update} | type {immediate | normal | permanent}}

7. Repeat Step 6 as required to finish modifying the cache parameters for this flow monitor.

8. statistics packet protocol

9. statistics packet size

10. exporter exporter-name

11. end

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

flow monitor monitor-name
Example:

Router(config)# flow monitor FLOW-MONITOR-1

Creates a flow monitor and enters Flexible NetFlow flow monitor configuration mode.

•This command also allows you to modify an existing flow monitor.

Step 4

description string
Example:

Router(config-flow-monitor)# description Used for basic ipv4 traffic analysis

(Optional) Creates a description for the flow monitor.

Step 5

record {record-name | netflow-original | netflow {ipv4 | ipv6} record [peer]}
Example:

Router(config-flow-monitor)# record FLOW-RECORD-1

Specifies the record for the flow monitor.

Step 6

cache {entries entries | timeout {active active | inactive inactive | update update} | type {immediate | normal | permanent}}
Example:

Router(config-flow-monitor)# cache entries 1000

(Optional) Modifies the flow monitor cache parameters such as timeout values, number of cache entries, and the cache type.

•The timeout keywords do not have any effect when the cache type is set to immediate.

Step 7

Repeat Step 6 as required to finish modifying the cache parameters for this flow monitor.

—

Step 8

statistics packet protocol
Example:

Router(config-flow-monitor)# statistics packet protocol

(Optional) Enables the collection of protocol distribution statistics for Flexible NetFlow monitors.

Step 9

statistics packet size
Example:

Router(config-flow-monitor)# statistics packet size

(Optional) Enables the collection of size distribution statistics for Flexible NetFlow monitors.

Step 10

exporter exporter-name
Example:

Router(config-flow-monitor)# exporter EXPORTER-1

(Optional) Specifies the name of an exporter that was created previously.

•Refer to the "Configuring Data Export for Cisco IOS Flexible NetFlow with Flow Exporters" module for information about and instructions for configuring flow exporters.

Step 11

end
Example:

Router(config-flow-monitor)# end

Exits flow monitor configuration mode and returns to privileged EXEC mode.

Verifying the Flow Monitor

To view the current status of a flow monitor and verify the configuration commands that you entered, perform the following optional task.

SUMMARY STEPS

1. enable

2. show flow monitor

3. show running-config flow monitor monitor-name

DETAILED STEPS

Step 1 enable

The enable command enters privileged EXEC mode (enter the password if prompted).
Router> enable
Router#
Step 2 show flow monitor monitor-name

The show flow monitor command shows the current status of the flow monitor that you specify.
Router# show flow monitor FLOW-MONITOR-1
Flow Monitor FLOW-MONITOR-1:
  Description:       Used for basic ipv4 traffic analysis
  Flow Record:       FLOW-RECORD-1
  Flow Exporter:     EXPORTER-1
  Cache:
    Type:              normal
    Status:            allocated
    Size:              1000 entries / 50052 bytes
    Inactive Timeout:  15 secs
    Active Timeout:    1800 secs
    Update Timeout:    1800 secs
  Stats:
    protocol distribution 
    size distribution
Step 3 show running-config flow monitor

The show running-config flow monitor command shows the configuration commands of the flow monitor that you specify.
Router# show running-config flow monitor FLOW-MONITOR-1
Current configuration:
!
flow monitor FLOW-MONITOR-1
 description Used for basic ipv4 traffic analysis
 record FLOW-RECORD-1
 exporter EXPORTER-1
 cache entries 1000
 statistics packet protocol
 statistics packet size
!
Applying a Flow Monitor to an Interface

Before it can be activated, a flow monitor must be applied to at least one interface. To activate a flow monitor, perform the following required task.

Restrictions

When you specify the "NetFlow original" or the "NetFlow IPv4 original input" or the "NetFlow IPv6 original input" predefined record for the flow monitor to emulate original NetFlow, the Flexible NetFlow flow monitor can be used only for analyzing input (ingress) traffic.

When you specify the "NetFlow IPv4 original output" or the "NetFlow IPv6 original output" predefined record for the flow monitor to emulate the Egress NetFlow Accounting feature, the Flexible NetFlow flow monitor can be used only for analyzing output (egress) traffic.

SUMMARY STEPS

1. enable

2. configure terminal

3. interface type number

4. {ip | ipv6} flow monitor monitor-name {input | output}

5. Repeat Steps 3 and 4 to activate a flow monitor on any other interfaces in the router over which you want to monitor traffic.

6. end

DETAILED STEPS

Command or Action

Purpose

Step 1

enable
Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2

configure terminal
Example:

Router# configure terminal

Enters global configuration mode.

Step 3

interface type number
Example:

Router(config)# interface ethernet 0/0

Specifies an interface and enters interface configuration mode.

Step 4

{ip | ipv6} flow monitor monitor-name {input | output}
Example:

Router(config-if)# ip flow monitor FLOW-MONITOR-1 input

Activates a flow monitor that was created previously by assigning it to the interface to analyze traffic.

Step 5

Repeat Steps 3 and 4 to activate a flow monitor on any other interfaces in the router over which you want to monitor traffic.

—

Step 6

end
Example:

Router(config-if)# end

Exits interface configuration mode and returns to privileged EXEC mode.

Verifying That Flexible NetFlow Is Enabled

To verify that Flexible NetFlow is enabled on an interface, perform the following optional task.

SUMMARY STEPS

1. enable

2. show flow interface

DETAILED STEPS

Step 1 enable

The enable command enters privileged EXEC mode (enter the password if prompted).
Router> enable
Router#
Step 2 show flow interface

The show flow interface command verifies that Flexible NetFlow is enabled on an interface.
Router# show flow interface ethernet 0/0
Interface Ethernet0/0
  FNF:  monitor:         FLOW-MONITOR-1
        direction:       Input
        traffic(ip):     on
  FNF:  monitor:         FLOW-MONITOR-2
        direction:       Input
        traffic(ipv6):   on
Router# show flow interface ethernet 1/0
Interface Ethernet1/0
  FNF:  monitor:         FLOW-MONITOR-1
        direction:       Output
        traffic(ip):     on
  FNF:  monitor:         FLOW-MONITOR-2
        direction:       Output
        traffic(ipv6):   on
Viewing the Flow Monitor Cache

To view the data in the flow monitor cache, perform the following optional task.

Prerequisites

The interface on which you applied the input flow monitor must be receiving traffic that meets the criteria defined by the NetFlow original record before you can view the flows in the flow monitor cache.

SUMMARY STEPS

1. enable

2. show flow monitor name monitor-name cache format record

DETAILED STEPS

Step 1 enable

The enable command enters privileged EXEC mode (enter the password if prompted).
Router> enable
Router#
Step 2 show flow monitor name monitor-name cache format record

The show flow monitor name monitor-name cache format record command string displays the status, statistics, and flow data in the cache for a flow monitor.
Router# show flow monitor name FLOW-MONITOR-1 cache format record
Cache type:                            Normal
  Cache size:                              1000
  Current entries:                            4
  High Watermark:                             4
  Flows added:                              101
  Flows aged:                                97
    - Active timeout   (  1800 secs)          3
    - Inactive timeout (    15 secs)         94
    - Event aged                              0
    - Watermark aged                          0
    - Emergency aged                          0
IPV4 DESTINATION ADDRESS:  172.16.10.5
ipv4 source address:       10.10.11.1
trns source port:          25
trns destination port:     25
counter bytes:             72840
counter packets:           1821
timestamp first:           21237828
timestamp last:            22086520
ip protocol:               6
IPV4 DESTINATION ADDRESS:  172.16.10.2
ipv4 source address:       10.10.10.2
trns source port:          20
trns destination port:     20
counter bytes:             3913860
counter packets:           7326
timestamp first:           21238788
timestamp last:            22088080
ip protocol:               6
IPV4 DESTINATION ADDRESS:  172.16.10.200
ipv4 source address:       192.168.67.6
trns source port:          0
trns destination port:     3073
counter bytes:             51072
counter packets:           1824
timestamp first:           21239228
timestamp last:            22087980
ip protocol:               1
Router# show flow monitor name FLOW-MONITOR-2 cache format record
Cache type:                            Normal
  Cache size:                              1000
  Current entries:                            2
  High Watermark:                             3
  Flows added:                               95
  Flows aged:                                93
    - Active timeout   (  1800 secs)          0
    - Inactive timeout (    15 secs)         93
    - Event aged                              0
    - Watermark aged                          0
    - Emergency aged                          0
IPV6 DESTINATION ADDRESS:  2001:DB8:4:ABCD::2
ipv6 source address:       2001:DB8:1:ABCD::1
trns source port:          33572
trns destination port:     23
counter bytes:             19140
counter packets:           349
timestamp first:           2172704
timestamp last:            2198272
ip protocol:               6
IPV6 DESTINATION ADDRESS:  FF02::9
ipv6 source address:       FE80::A8AA:BBFF:FEBB:CC03
trns source port:          521
trns destination port:     521
counter bytes:             92
counter packets:           1
timestamp first:           2195672
timestamp last:            2195672
ip protocol:               17
Configuration Examples for Customizing Flexible NetFlow Flow Records and Flow Monitors

This section provides the following configuration examples:

•Configuring a Permanent Flow Record Cache with a Limited Number of Possible Flows: Example

•Configuring a Customized Flow Record Cache for Monitoring IPv6 Traffic: Example

•Configuring Flexible NetFlow for Monitoring MAC and VLAN Statistics: Example

•Configuring Flexible NetFlow for Ingress VRF Support: Example

•Configuring Flexible NetFlow for Network Based Application Recognition (NBAR) : Example

Configuring a Permanent Flow Record Cache with a Limited Number of Possible Flows: Example

The following example is designed to monitor the type of service (ToS) field usage on all interfaces in the router. An exporter is not configured because this example is intended to be used to capture additional data for analysis on the router using the show flow monitor command.

This sample starts in global configuration mode:
!
ip cef
!
flow record QOS_RECORD
 description UD: Flow Record to monitor the use of TOS within this router/network
 match interface input
 match interface output
 match ipv4 tos
 collect counter packets
 collect counter bytes
 exit
!
flow monitor QOS_MONITOR
 description UD: Flow Monitor which watches the limited combinations of interface and TOS
 record QOS_RECORD
 cache type permanent
 cache entries 8192   ! 2^5 (combos of interfaces) * 256 (values of TOS)
 exit
!
interface ethernet0/0
 ip flow monitor QOS_MONITOR input
 exit
!
interface ethernet0/1
 ip flow monitor QOS_MONITOR input
 exit
!
interface ethernet0/2
 ip flow monitor QOS_MONITOR input
 exit
!
interface serial2/0
 ip flow monitor QOS_MONITOR input
 exit
!
interface serial2/1
 ip flow monitor QOS_MONITOR input
!
The display from the show flow monitor command shows the current status of the cache.
Router# show flow monitor QOS_MONITOR cache
  Cache type:                         Permanent
  Cache size:                              8192
  Current entries:                            2
  High Watermark:                             2
  Flows added:                                2
  Updates sent         (  1800 secs)          0
Configuring a Customized Flow Record Cache for Monitoring IPv6 Traffic: Example

The following example creates a customized flow record for monitoring common IPv6 traffic characteristics.

This sample starts in global configuration mode:
!
ip cef
ipv6 cef
!
flow record FLOW-RECORD-2
 description Used for basic IPv6 traffic analysis
 match ipv6 destination address
 collect ipv6 protocol
 collect ipv6 source address
 collect transport source-port
 collect transport destination-port
 collect counter bytes
 collect counter packets
 collect timestamp sys-uptime first
 collect timestamp sys-uptime last
!
flow monitor FLOW-MONITOR-2
 description Used for basic IPv6 traffic analysis
 record FLOW-RECORD-2
 cache entries 1000
 statistics packet protocol
 statistics packet size
!
interface Ethernet0/0
 ipv6 address 2001:DB8:2:ABCD::2/48
 ipv6 flow monitor FLOW-MONITOR-2 input
!
interface Ethernet1/0
 ipv6 address 2001:DB8:3:ABCD::1/48
 ipv6 flow monitor FLOW-MONITOR-2 output
!
Configuring Flexible NetFlow for Monitoring MAC and VLAN Statistics: Example

The following example shows how to configure Flexible NetFlow for monitoring MAC and VLAN statistics.

This sample starts in global configuration mode:
!
 flow record LAYER-2-FIELDS-1
 match ipv4 source address
 match ipv4 destination address
 collect datalink dot1q vlan output
 collect datalink mac source address input
 collect datalink mac source address output
 collect datalink mac destination address input
 collect flow direction
 collect counter bytes
 collect counter packets
!
 exit
!
!
flow monitor FLOW-MONITOR-4
 record LAYER-2-FIELDS-1
 exit
!
ip cef
!
interface Ethernet0/0
 ip address 172.16.6.2 255.255.255.0
 ip flow monitor FLOW-MONITOR-1 input
!
Configuring Flexible NetFlow for Ingress VRF Support: Example

The following example configures the collection of the virtual route forwarding (VRF) ID from incoming packets on a router by applying an input flow monitor having a flow record that collects the VRF ID as a key field.

This sample starts in global configuration mode:
!
flow record rm_1
match routing vrf input
match ipv4 source address
match ipv4 destination address
collect interface input
collect interface output
collect counter packets
!
flow monitor mm_1
record rm_1
!
interface Serial2/0
ip vrf forwarding green
ip address 172.16.2.2 255.255.255.252
ip flow monitor mm_1 output
!
end
Configuring Flexible NetFlow for Network Based Application Recognition (NBAR) : Example

The following example creates different flows for each application seen between any two IP hosts by applying a flow monitor having a flow record that collects the application name as a key field.

This sample starts in global configuration mode:
!
flow record rm_1
match application name
match ipv4 source address
match ipv4 destination address
collect interface input
collect interface output
collect counter packets
!
flow monitor mm_1
record rm_1
!
interface FastEthernet0/0
ip address 172.16.2.2 255.255.255.0
ip flow monitor mm_1 input
!
end
Where to Go Next

If you want to configure data export for Flexible NetFlow, refer to the "Configuring Data Export for Cisco IOS Flexible NetFlow with Flow Exporters" module.

If you want to configure flow sampling to reduce the CPU overhead of analyzing traffic, refer to the "Using Cisco IOS Flexible NetFlow Flow Sampling to Reduce the CPU Overhead of Analyzing Traffic" module.

If you want to configure any of the predefined records for Flexible NetFlow, refer to the "Configuring Cisco IOS Flexible NetFlow with Predefined Records" module.

Additional References

The following sections provide references related to Flexible NetFlow.

Related Documents

Related Topic

Document Title

Cisco IOS commands

Cisco IOS Master Commands List, All Releases

Overview of Flexible NetFlow

"Cisco IOS Flexible NetFlow Overview"

Flexible NetFlow Feature Roadmap

"Cisco IOS Flexible NetFlow Features Roadmap"

Emulating original NetFlow with Flexible NetFlow

"Getting Started with Configuring Cisco IOS Flexible NetFlow"

Configuring flow exporters to export Flexible NetFlow data.

"Configuring Data Export for Cisco IOS Flexible NetFlow with Flow Exporters"

Configuring flow sampling to reduce the overhead of monitoring traffic with Flexible NetFlow

"Using Cisco IOS Flexible NetFlow Flow Sampling to Reduce the CPU Overhead of Analyzing Traffic"

Configuring Flexible NetFlow using predefined records

"Configuring Cisco IOS Flexible NetFlow with Predefined Records"

Using Flexible NetFlow Top N Talkers to Analyze Network Traffic

"Using Cisco IOS Flexible NetFlow Top N Talkers to Analyze Network Traffic"

Configuring IPv4 Multicast Statistics Support for Flexible NetFlow

"Configuring IPv4 Multicast Statistics Support for Cisco IOS Flexible NetFlow"

Configuration commands for Flexible NetFlow

Cisco IOS Flexible NetFlow Command Reference

Standards

Standard

Title

There are no standards associated with this feature.

—

MIBs

MIB

MIBs Link

None

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

RFCs

RFC

Title

RFC 3954

Cisco Systems NetFlow Services Export Version 9

Technical Assistance

Description

Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html

Feature Information for Flexible NetFlow

Table 1 lists the features in this module and provides links to specific configuration information. Only features that were introduced or modified in Cisco IOS Release 12.2(1) or Cisco IOS Releases 12.2(1) or 12.0(3)S or a later release appear in the table.

For information on a feature in this technology that is not documented here, see the "Cisco IOS Flexible NetFlow Features Roadmap".

Not all commands may be available in your Cisco IOS software release. For release information about a specific command, see the command reference documentation.

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS, Catalyst OS, and Cisco IOS XE software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.

Note Table 1 lists only the Cisco IOS software release that introduced support for a given feature in a given Cisco IOS software release train. Unless noted otherwise, subsequent releases of that Cisco IOS software release train also support that feature.

Table 1 Feature Information for Flexible NetFlow

Feature Name

Releases

Feature Configuration Information

Flexible NetFlow

12.4(9)T

12.2(33)SRC

Flexible NetFlow is introduced.

Support for this feature was added for Cisco 7200 series routers in Cisco IOS Release 12.2(33)SRC.

Information about the Flexible NetFlow feature is included in the following sections:

•Prerequisites for Customizing Flexible NetFlow Flow Records and Flow Monitors

•Information About Customizing Flexible NetFlow Flow Records and Flow Monitors

•How to Customize Flexible NetFlow Flow Records and Flow Monitors

•Configuration Examples for Customizing Flexible NetFlow Flow Records and Flow Monitors

The following commands were introduced or modified: cache (Flexible NetFlow), clear flow exporter, clear flow monitor, clear sampler, collect counter, collect flow, collect interface, collect ipv4, collect ipv4 destination, collect ipv4 fragmentation, collect ipv4 section, collect ipv4 source, collect ipv4 total-length, collect ipv4 ttl, collect routing, collect timestamp sys-uptime, collect transport, collect transport icmp ipv4, collect transport tcp, collect transport udp, debug flow exporter, debug flow monitor, debug flow record, debug sampler, description (Flexible NetFlow), destination, dscp (Flexible NetFlow), exporter, flow exporter, flow monitor, flow record, ip flow monitor, match flow, match interface (Flexible NetFlow), match ipv4, match ipv4 destination, match ipv4 fragmentation, match ipv4 section, match ipv4 source, match ipv4 total-length, match ipv4 ttl, match routing, match transport, match transport icmp ipv4, match transport tcp, match transport udp, mode (Flexible NetFlow), option (Flexible NetFlow), record, sampler, show flow exporter, show flow interface, show flow monitor, show flow record, show sampler, source (Flexible NetFlow), statistics packet, template data timeout, transport (Flexible NetFlow).

Flexible NetFlow—IPv4 Unicast Flows

12.4(9)T

12.2(33)SRC

Enables Flexible NetFlow to monitor IPv4 traffic.

Support for this feature was added for Cisco 7200 series routers in Cisco IOS Release 12.2(33)SRC.

Information about the Flexible NetFlow—IPv4 Unicast Flows feature is included in the following sections:

•Configuring a Customized Flow Record for IPv4 Traffic

•Applying a Flow Monitor to an Interface

The following commands were introduced or modified: collect routing, debug flow record, collect ipv4, collect ipv4 destination, collect ipv4 fragmentation, collect ipv4 section, collect ipv4 source, ip flow monitor, match ipv4, match ipv4 destination, match ipv4 fragmentation, match ipv4 section, match ipv4 source, match routing, record, show flow monitor, show flow record.

Flexible NetFlow—Layer 2 Fields

12.4(22)T 12.2(33)SRE

Enables collecting statistics for Layer 2 fields such as MAC addresses and virtual LAN (VLAN) IDs from traffic.

Support for this feature was added for Cisco 7200 and 7300 NPE series routers in Cisco IOS Release 12.2(33)SRE.

Information about the Flexible NetFlow—Layer 2 Fields feature is included in the following sections:

•Configuring Flexible NetFlow for Monitoring MAC and VLAN Statistics: Example

The following commands were introduced or modified:

collect datalink dot1q vlan, collect datalink mac, match datalink dot1q vlan, match datalink mac.

Flexible NetFlow—IPv6 Unicast Flows

12.4(20)T

12.2(33)SRE

Enables Flexible NetFlow to monitor IPv6 traffic.

Support for this feature was added for Cisco 7200 and 7300 NPE series routers in Cisco IOS Release 12.2(33)SRE.

Information about the Flexible NetFlow—IPv6 Unicast Flows feature is included in the following sections:

•Configuring a Customized Flow Record for IPv6 Traffic

•Applying a Flow Monitor to an Interface

•Configuring a Customized Flow Record Cache for Monitoring IPv6 Traffic: Example

The following commands were introduced or modified: collect routing, debug flow record, match routing, record, show flow monitor, show flow record, collect ipv6, collect ipv6 destination, collect ipv6 extension map, collect ipv6 fragmentation, collect ipv6 hop-limit, collect ipv6 length, collect ipv6 section, collect ipv6 source, collect transport icmp ipv6, ipv6 flow monitor, match ipv6, match ipv6 destination, match ipv6 extension map, match ipv6 fragmentation, match ipv6 hop-limit, match ipv6 length, match ipv6 section, match ipv6 source, match transport icmp ipv6.

Flexible NetFlow—Ingress VRF Support

15.0(1)M

12.2(33)SRE

Enables collecting the virtual route forwarding (VRF) ID from incoming packets on a router by applying an input flow monitor having a flow record that collects the VRF ID as a key or a non-key field.

Support for this feature was added for Cisco 7200 and 7300 NPE series routers in Cisco IOS Release 12.2(33)SRE.

Information about the Flexible NetFlow—Ingress VRF Support feature is included in the following sections:

•Configuring Flexible NetFlow for Ingress VRF Support: Example

The following commands were introduced or modified:

collect routing, match routing, option (Flexible NetFlow), show flow monitor.

Flexible NetFlow—NBAR Application Recognition

15.0(1)M

Enables creation of different flows for each application seen between any two IP hosts by applying a flow monitor having a flow record that collects the application name as a key or a non-key field.

Information about the NBAR Application Recognition feature is included in the following sections:

•Configuring Flexible NetFlow for Network Based Application Recognition (NBAR) : Example

The following commands were introduced or modified:

collect application name, match application name, option (Flexible NetFlow), show flow monitor.

CCDE, CCENT, CCSI, Cisco Eos, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Nurse Connect, Cisco Pulse, Cisco SensorBase, Cisco StackPower, Cisco StadiumVision, Cisco TelePresence, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels, Flip for Good, Flip Mino, Flipshare (Design), Flip Ultra, Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn, Cisco Capital, Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store, Flip Gift Card, and One Million Acts of Green are service marks; and Access Registrar, Aironet, AllTouch, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Lumin, Cisco Nexus, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, Continuum, EtherFast, EtherSwitch, Event Center, Explorer, Follow Me Browsing, GainMaker, iLYNX, IOS, iPhone, IronPort, the IronPort logo, Laser Link, LightStream, Linksys, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, PCNow, PIX, PowerKEY, PowerPanels, PowerTV, PowerTV (Design), PowerVu, Prisma, ProConnect, ROSA, SenderBase, SMARTnet, Spectrum Expert, StackWise, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0910R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

© 2008-2009 Cisco Systems, Inc. All rights reserved.