1/2 Port Channelized Ti/E1 PRI Network Module (NM-1CE1TE1-PRI and NM-2CE1T1-PRI)
Download this chapter
1/2 Port Channelized Ti/E1 PRI Network Module (NM-1CE1TE1-PRI and NM-2CE1T1-PRI)1/2 Port Channelized Ti/E1 PRI Network Module (NM-1CE1TE1-PRI and NM-2CE1T1-PRI)
 Feedback

Table Of Contents

1/2 Port Channelized T1/E1 PRI Network Module (NM-1CE1T1-PRI and NM-2CE1T1-PRI)

Contents

Information About NM-xCE1T1-PRI Support

NM-xCE1T1-PRI Feature Driver Software

NM-xCE1T1-PRI Feature Supported Functions

How to Configure the NM-xCE1T1-PRI Feature

Configuring an NM-xCE1T1-PRI Card for a T1 Interface

Configuring an NM-xCE1T1-PRI Card for an E1 Interface

Configuring a T1 or E1 Interface for Bantam-Jack Monitoring

Verifying NM-xCE1T1-PRI Support

Examples

Configuration Examples for NM-xCE1T1-PRI Support

T1 Interface Example

E1 Interface Example

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Command Reference

Glossary


1/2 Port Channelized T1/E1 PRI Network Module (NM-1CE1T1-PRI and NM-2CE1T1-PRI)

The NM-1CE1T1-PRI (1-port) and NM-2CE1T1-PRI (2-port) network modules provide support for T1, E1, and ISDN primary rate interface (PRI) network connections in a network module form factor. This feature (referred to in this document as NM-xCE1T1-PRI) offers attachment of one T1, E1, or ISDN PRI line on the 1-port module and two T1, E1, or ISDN PRI lines on the 2-port version.

This new feature (NM-xCE1T1-PRI) enables you to configure a single network module as either a T1 interface or an E1 interface on the same card. The configuration of a T1 or E1 interface and the change from one to the other is controlled by the card type command. Additionally, when in E1 mode, the module can be configured between channelized E1, ISDN PRI, E1-CAS-R2, balanced and unbalanced, and structured (G.704) versus unstructured (G.703) modes. In T1 mode, the module can be configured for channelized T1, T1-CAS, and as a CSU/DSU.

Note After you insert the NM-xCE1T1-PRI feature network module into the router chassis, you must use the card type command in the command-line interface (CLI) to configure the NM-xCE1T1-PRI feature. The controller will not be detected and cannot be configured until you use the card type command.

Configuration of the T1 or E1 interface can be customized using command-line interface (CLI) commands. In E1 mode, each port can be individually set to 120-ohm or 75-ohm termination. Each port has RJ-48C connectors, and there is one bantam jack that is shared by each port (for 2-port cards) for monitoring.

Feature Specifications for the 1/2 Port Channelized T1/E1 PRI Network Module

Feature History
 
Release
Modification

12.3(1)

This feature was introduced in Cisco IOS Release 12.3(1).

Supported Platforms

Cisco 2610XM, Cisco 2611XM, Cisco 2620XM, Cisco 2621XM, Cisco 2650XM, Cisco 2651XM, Cisco 2691, Cisco 3631, Cisco 3660, Cisco 3725, and Cisco 3745.

This feature is not supported on the Cisco 3620 and Cisco 3640 platforms. For the Cisco 2600 series,
only the Cisco 2610-2651XM series and Cisco 2691 are supported. Cisco 2610-2651 (non-XM) are not supported.


Finding Support Information for Platforms and Cisco IOS Software Images

Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image support. Access Cisco Feature Navigator at http://www.cisco.com/go/fn. You must have an account on Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear.

Contents

•Information About NM-xCE1T1-PRI Support

•How to Configure the NM-xCE1T1-PRI Feature

•Configuration Examples for NM-xCE1T1-PRI Support

•Additional References

•Command Reference

•Glossary

Information About NM-xCE1T1-PRI Support

After you insert the NM-xCE1T1-PRI feature network module into the router chassis, you must use the card type command in the command-line interface (CLI) to configure the NM-xCE1T1-PRI feature. The controller will not be detected and cannot be configured until you use the card type command.

If the card type command is used to make subsequent changes, these changes will take effect only if you use the reload command after changing the card type.

The bantam jack can be connected only to one port at a time.

The NM-xCE1T1-PRI feature will not support channel service unit (CSU) DTE loopback or CSU network loopback modes. Because the CSU is integrated into the framer, there is no need or way to support CSU loopbacks.

To configure the NM-xCE1T1-PRI feature, you need to understand the following concepts:

•NM-xCE1T1-PRI Feature Driver Software

•NM-xCE1T1-PRI Feature Supported Functions

NM-xCE1T1-PRI Feature Driver Software

The driver software for the NM-xCE1T1-PRI feature provides for the transmission and reception of packets over channelized E1 and T1 circuits. Driver functions are as follows:

•Network Management Interface (MIB support)

•New CLI for 75-ohm and 120-ohm line termination for E1

•New CLI for specifying the card type (T1/E1)

NM-xCE1T1-PRI Feature Supported Functions

This section summarizes the functions supported by the NM-xCE1T11PRI feature.

•Two card versions:

–1-port T1 (DSU/CSU), E1 and G.703 (balanced and unbalanced)

–2-port T1 (DSU/CSU), E1 and G.703 (balanced and unbalanced)

•Four LEDs per port defined as Carrier Detect, Remote Alarm, Local Alarm, and Loopback

•Three LEDs per port defined as T1-100, E1-120, and E1-75

•RJ-48 connectors with transition cable breakout to physical media type

•T1 CSU and DSU line buildouts, E1 short haul and long haul

•T1 SF and ESF framing

•ANSI T1.403 Annex B/V.54 loopup/loopdown code recognition, network loopback, and user-initiated loopbacks

•E1 structured (ITU G.704) and unstructured (ITU G.703) operation

•AMI, B8ZS, and HDB3 line coding

•Two bantam jacks for TX and RX monitor with two LEDs defined as P0, P1 (port selected)

How to Configure the NM-xCE1T1-PRI Feature

This section describes the commands used to configure the NM-xCE1T1-PRI feature:

•Configuring an NM-xCE1T1-PRI Card for a T1 Interface

•Configuring an NM-xCE1T1-PRI Card for an E1 Interface

•Configuring a T1 or E1 Interface for Bantam-Jack Monitoring

•Verifying NM-xCE1T1-PRI Support

Configuring an NM-xCE1T1-PRI Card for a T1 Interface

Perform this task to select and configure a network module card as T1.

SUMMARY STEPS

1. enable

2. configure terminal

3. card type t1 slot

4. controller t1 slot/port

5. linecode {ami | b8zs}

6. framing {sf | esf}

7. clock source {line | internal}

8. pri-group [timeslots range]

9. exit

10. copy running-config startup-config

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

card type t1 slot

Example:

Router(config)# card type t1 1

Sets or changes the card type.

•When the command is used for the first time, the configuration takes effect immediately.

•A subsequent change in the card type will not take effect unless you enter the reload command or reboot the router.

Step 4 

controller t1 slot/port

Example:

Router(config)# controller t1 1/0

Enters controller configuration mode and identifies the controller type (T1) and a slot and port for configuration commands that specifically apply to the T1 interface.

•The card type command must be entered before this command can be used.

Step 5 

linecode {ami | b8zs}

Example:

Router(config-controller)# linecode b8zs

Specifies a line encoding for a controller.

•The controller command must be entered before this command can be used.

•Line-code value for T1 can be ami or b8zs.

Step 6 

framing {sf | esf}

Example:

Router(config-controller)# framing esf

Specifies a frame type.

•The controller command must be entered before this command can be used.

•The frame type can be specified as sf for superframe or esf for extended superframe for T1 controllers.

Step 7 

clock source {line | internal}

Example:

Router(config-controller)# clock source line

Sets the clock source for a T1 controller.

•The clocking argument can have a value of line or internal.

–A value of line means the source is the loop.

–A value of internal means the source is the local oscillator if the card is not participating in the backplane timing domain.

Step 8  

pri-group [timeslots range]
Example:

Router(config-controller)# pri-group timeslots 1-5

Specifies that the controller should be set up as a PRI interface.

•For T1, the last defined channel is the D channel.

•If a controller is configured as PRI, individual channel groups cannot be configured on that controller.

•The controller command must be entered before this command can be used.

Note To specify that the controller should be set up as a channel group, use the channel-group command here instead of the pri-group command. For more information, see the "Configuring an NM-xCE1T1-PRI Card for an E1 Interface" section.

Step 9 

exit

Example:

Router# exit

Exits the controller configuration mode and returns the router to privileged EXEC mode.

Step 10 

copy running-config startup-config

Example:

Router# copy running-config startup-config

Saves the new configuration parameters to the permanent configuration file.

•This command can be abbreviated to copy run start.


Configuring an NM-xCE1T1-PRI Card for an E1 Interface

Perform this task to select and configure an NM-xCE1T1-PRI network module card as E1.

SUMMARY STEPS

1. enable

2. configure terminal

3. card type e1 slot

4. controller e1 slot/port

5. linecode {ami | hdb3}

6. framing {crc4 | no-crc4}

7. clock source {line | internal}

8. channel-group channel-number {timeslots range [speed {56 | 64}] | unframed}

9. line termination {75-ohm | 120-ohm}

10. exit

11. copy running-config startup-config

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

card type e1 slot

Example:

Router(config)# card type e1 1

Sets or changes the card type.

•When the command is used for the first time, the configuration takes effect immediately.

•A subsequent change in the card type will not take effect unless you enter the reload command or reboot the router.

Step 4 

controller e1 slot/port

Example:

Router(config)# controller e1 1/0

Enters controller configuration mode and identifies the controller type (E1) and a slot and port for configuration commands that specifically apply to the E1 interface.

•The card type command must be entered before this command can be used.

Step 5 

linecode {ami | hdb3}

Example:

Router(config-controller)# linecode hdb3

Specifies a line encoding for a controller.

•The controller command must be entered before this command can be used.

•Linecode value for E1 can be ami or hdb3.

Step 6  

framing {crc4 | no-crc4}
Example:

Router(config-controller)# framing crc4

Selects a frame type.

•The controller command must be entered before this command.

•The framing value can be crc4 or no crc4 for E1 controllers.

Step 7 

clock source {line | internal}

Example:

Router(config-controller)# clock source line

Sets the clock source for an E1 controller.

•The clocking argument can have a value of line or internal.

–A value of line means the source is the loop.

–A value of internal means the source is the local oscillator if the card is not participating in the backplane timing domain.

Step 8  

channel-group channel-number {timeslots range 
[speed {56 | 64}] | unframed}
Example: 
Router(config-controller)# channel-group 1 
unframed

Specifies that the controller should be set up as a channelized interface.

•Defines the time slots that belong to each E1 circuit.

•When a T1 data line is configured, channel-group numbers can be values from 0 to 23.

•When an E1 data line is configured, channel-group numbers can be values from 0 to 30.

•The unframed keyword specifies that all 32 time slots are used for data. None of the 32 time slots are used for framing signals.

•The controller command must be entered before this command can be used.

Note T o specify that the controller should be set up as a PRI group, use the pri-group command here instead of the channel-group command. For more information, see the "Configuring an NM-xCE1T1-PRI Card for a T1 Interface" section.

Step 9  

line-termination {75-ohm | 120-ohm}
Example:

Router(config-controller)# line-termination 120-ohm

Configures the E1 line interface for 120-ohm or 75-ohm termination.

•The controller command must be entered before this command can be used.

•Line termination is configurable only for E1.

Step 10 

exit

Example:

Router# exit

Exits the controller configuration mode and returns the router to privileged EXEC mode.

Step 11 

copy running-config startup-config

Example:

Router# copy running-config startup-config

Saves the new configuration parameters to the permanent configuration file.

•This command can be abbreviated to copy run start.


Configuring a T1 or E1 Interface for Bantam-Jack Monitoring

Perform this task to enable monitoring of the TX and RX lines of a T1 or E1 port on the onboard bantam jack.

Note Only one port can be monitored at a time. Disable the bantam-jack monitoring if you are not actively monitoring the TX and RX activity for a port.

SUMMARY STEPS

1. enable

2. configure terminal

3. card type {t1 | e1} slot

4. controller {t1 | e1} slot/port

5. bantam-jack enable

6. no bantam-jack enable

7. exit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3 

card type {t1 | e1} slot

Example:

Router(config)# card type e1 1

Sets or changes the card type.

•When the command is used for the first time, the configuration takes effect immediately.

•A subsequent change in the card type will not take effect unless you enter the reload command or reboot the router.

Step 4 

controller {t1 | e1} slot/port

Example:

Router(config)# controller e1 1/0

Enters controller configuration mode and identifies the controller type (T1 or E1) and a slot and port for configuration commands that specifically apply to the T1 or E1 interface.

•The card type command must be entered before this command can be used.

Step 5 

bantam-jack enable

Example:

Router(config-controller)# bantam-jack enable

Monitors the TX and RX lines of a T1 or E1 port on the onboard bantam jack.

•Only one port can be monitored at a time.

Step 6 

no bantam-jack enable

Example:

Router(config-controller)# no bantam-jack enable

Disables the monitoring function of the TX and RX lines of a T1 or E1 port on the onboard bantam jack.

•Only one port can be monitored at a time.

•Always disable the monitoring function of the TX and RX lines when you are not actively monitoring the lines.

Step 7 

exit

Example:

Router# exit

Exits controller configuration mode and returns the router to privileged EXEC mode.


Verifying NM-xCE1T1-PRI Support

To examine the state of the T1 or E1 line, use the show controller and show interface commands.

SUMMARY STEPS

1. enable

2. show controller {t1 | e1}

3. show interfaces serial slot/port:[channel-group]

4. show pci bridge slot-number

 
Command or Action
Purpose

Step 1 

enable

Example:

Router> enable

Enables privileged EXEC mode.

•Enter your password if prompted.

Step 2 

show controller {t1 | e1}

Example:

Router# show controller t1

Displays the RFC 1406 MIB statistics about the T1 or E1 port, card revision information, alarm status, and port configuration.

Step 3 

show interfaces serial slot/port:[channel-group]

Example:

Router# show interfaces serial 1/0:23

Displays statistics for channels and channel groups created within a T1 or E1 controller, which are treated as serial interfaces.

•The range of slot numbers is dependent on the host router.

•The port can be either 0 or 1.

•Channel-group values range from 0 to 23 for T1 controllers and from 0 to 30 for E1 controllers.

•The channel group is the number parameter defined in the channel-group command.

•If no channel-group value is entered, all the interfaces are displayed.

Step 4 

show pci bridge slot-number

Example:

Router# show pci bridge 1

Displays peripheral component interconnect (PCI) configuration information about the port module in a particular slot, including any bridges on both the host router and the network module.


Examples

This section describes commands that can be used to examine the state of the T1 or E1 lines.

•Using the show controller Command Example

•Using the show interfaces Command Example

•Using the show interfaces Command for a Particular Slot or Port Example

Using the show controller Command Example

The following is example output from a show controller command: 

Router#show controller E1

E1 1/0 is up.

  Applique type is Channelized E1 - balanced

  No alarms detected.

  alarm-trigger is not set

  Framing is UNFRAMED, Line Code is HDB3, Clock Source is Line.

  Bantam Jack Enabled										<---- indicates bantam-jack monitoring is enabled

  Module type is Channelized E1/T1 PRI

  Version info Firmware: 0000001D, FPGA: 0

  Hardware revision is 0.2         , Software revision is 29

  Protocol revision is 1

  number of CLI resets is 1

  Last clearing of alarm counters 00:00:10

    receive remote alarm  :    0, 

    transmit remote alarm :    0, 

    receive AIS alarm     :    0, 

    transmit AIS alarm    :    0, 

    loss of frame         :    0, 

    loss of signal        :    0, 

    Loopback test         :    0, 

    transmit AIS in TS 16 :    0, 

    receive LOMF alarm    :    0, 

    transmit LOMF alarm   :    0, 

  MIB data updated every 10 seconds.

  Data in current interval (10 seconds elapsed):

     0 Line Code Violations, 0 Path Code Violations

     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Using the show interfaces Command Example

The following is example output from a show interfaces command: 

Router# show interfaces serial 0/0:0


Serial0/0:0 is up, line protocol is up

Hardware is DSX1

Internet address is 10.0.0.1 255.0.0.0

MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 9/255

Encapsulation HDLC, loopback not set, keepalive not set

Last input 0:15:34, output 0:00:00, output hang never

Last clearing of "show interface" counters never

Output queue 2/40, 0 drops; input queue 0/75, 0 drops

5 minute input rate 56000 bits/sec, 195 packets/sec

5 minute output rate 56000 bits/sec, 196 packets/sec

8728809 packets input, 338385740 bytes, 0 no buffer

	Received 0 broadcasts, 0 runts, 0 giants

	0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

	8729371 packets output, 338413798 bytes, 0 underruns

	0 output errors, 0 collisions, 6 interface resets, 0 restarts

	0 output buffer failures, 0 output buffers swapped out

	0 carrier transitions

DCD=up DSR=up DTR=up RTS=up CTS=up

.

.

.

Serial0/0:23 is up, line protocol is up

Hardware is DSX1

Internet address is 10.0.0.2 255.0.0.0

MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 9/255

Encapsulation HDLC, loopback not set, keepalive not set

Last input 0:15:34, output 0:00:00, output hang never

Last clearing of "show interface" counters never

Output queue 2/40, 0 drops; input queue 0/75, 0 drops

5 minute input rate 56000 bits/sec, 195 packets/sec

5 minute output rate 56000 bits/sec, 196 packets/sec

8728809 packets input, 338385740 bytes, 0 no buffer

	Received 0 broadcasts, 0 runts, 0 giants

	0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

	8729371 packets output, 338413798 bytes, 0 underruns

	0 output errors, 0 collisions, 6 interface resets, 0 restarts

	0 output buffer failures, 0 output buffers swapped out

	0 carrier transitions

DCD=up DSR=up DTR=up RTS=up CTS=up

Using the show interfaces Command for a Particular Slot or Port Example

The following is example output from a show interfaces command for a particular slot or port: 

Router# show interfaces serial 1/0:18


Serial 1/0:18 is up, line protocol is up

Hardware is DSX1

Internet address is 10.0.0.2 255.0.0.0

MTU 1500 bytes, BW 9 Kbit, DLY 100000 usec, rely 255/255, load 1/255

Encapsulation SLIP, loopback not set

DTR is pulsed for 5 seconds on reset

Last input never, output never, output hang never

Last clearing of "show interface" counters never

Output queue 0/10, 0 drops; input queue 0/75, 0 drops

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

     Received 0 broadcasts, 0 runts, 0 giants

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

     0 packets output, 0 bytes, 0 underruns

     0 output errors, 0 collisions, 0 interface resets, 0 restarts

     0 output buffer failures, 0 output buffers swapped out

     0 carrier transitions

The commands to display the accounting and statistics on a particular interface will be the show interfaces interface 1/0:18 accounting and show interface interface 1/0:18 stats commands. The output for these cases will be identical to that for all other Cisco interfaces.

Configuration Examples for NM-xCE1T1-PRI Support

This section shows example configuration files for a T1 interface and an E1 interface.

•T1 Interface Example

•E1 Interface Example

T1 Interface Example

This sample configuration is for a Cisco 3745 with two cards in slots 1 and 3 configured for T1: 

Router# show running configuration


Building configuration...


Current configuration: 1744 bytes

!

version 12.2

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname host1

!

card type t1 1

card type t1 3

!

ip subnet-zero

!

!

!

isdn switch-type primary-dms100

!

!

voice call carrier capacity active

!

!

!         

!

!

!

!

!

!

mta receive maximum-recipients 0

!

controller T1 1/0

 framing esf

 linecode b8zs

 cablelength long 0db

 pri-group timeslots 1-24

!

controller T1 1/1

 framing esf

 linecode b8zs

 cablelength long 0db

 pri-group timeslots 1-24

!

controller T1 3/0

 framing esf

 linecode b8zs

 cablelength long 0db

 pri-group timeslots 1-24

!

controller T1 3/1

 framing esf

 linecode b8zs

 cablelength long 0db

 pri-group timeslots 1-24

!

!

!

!

interface FastEthernet0/0

 no ip address

 shutdown

 speed 100

 full-duplex

!

interface Serial0/0

 no ip address

 clockrate 2000000

!

interface FastEthernet0/1

 no ip address

 duplex auto

 speed 10

!

interface Serial0/1

 no ip address

 shutdown

!

interface Serial1/0:23

 no ip address

 isdn switch-type primary-dms100

 no cdp enable

!

interface Serial1/1:23

 no ip address

 isdn switch-type primary-dms100

 no cdp enable

!

interface FastEthernet2/0

 no ip address

 shutdown

 duplex auto

 speed auto

!

interface TokenRing2/0

 no ip address

 shutdown

 ring-speed 16

!

interface Serial3/0:23

 no ip address

 isdn switch-type primary-dms100

 no cdp enable

!

interface Serial3/1:23

 no ip address

 isdn switch-type primary-dms100

 no cdp enable

!

ip classless

ip http server

ip pim bidir-enable

!

!

dialer-list 1 protocol ip permit

!

!

!

call rsvp-sync

!

!

mgcp profile default

!

dial-peer cor custom

!

!

!

!

line con 0

 exec-timeout 0 0

line aux 0

line vty 0 4

 login

!

end

E1 Interface Example 

Current configuration : 1667 bytes

!

version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname router

!

card type e1 1

no logging buffered

!

ip subnet-zero

!

!

isdn switch-type primary-net5

!

!

!

controller E1 1/0

 channel-group 1 unframed

!

controller E1 1/1

 channel-group 1 unframed

!

!

interface FastEthernet0/0

 no ip address

 duplex auto

 speed auto

!

interface FastEthernet0/1

 no ip address

 load-interval 30

 shutdown

 speed 100

 full-duplex

 no cdp enable

!

interface 1/0:1

 no ip address

!

interface 1/1:1

 no ip address

!

!

ip http server

ip classless

!

!

line con 0

 exec-timeout 0 0

line aux 0

line vty 0 4

 exec-timeout 0 0

 login

!

!

end

Additional References

The following sections provide additional references related to the NM-xCE1T1-PRI feature:

•Related Documents

•Standards

•MIBs

•RFCs

•Technical Assistance

Related Documents

Related Topic
Document Title

Hardware installation instructions for the 1/2 Port Channelized T1/E1 PRI Network Module

Cisco Network Module Hardware Installation Guide


Standards

Standards
Title

ANSI T1.403-1995

Network to Customer Installation—DS1 Metallic Interface

ITU Recommendation G.703

Physical/Electrical Characteristics of Hierarchical Digital Interfaces (July 1988)

AT&T Publication 54016

Requirements for Interfacing Digital Terminal Equipment to Services Employing the Extended Super Frame Format


MIBs

MIBs
MIBs Link

•CISCO-ICSUDSU-MIB

•RFC 1406 MIB

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs


RFCs

RFCs
Title

RFC 1406

Definitions of Managed Objects for the DS1 and E1 Interface Types


Technical Assistance

Description
Link

Technical Assistance Center (TAC) home page, containing 30,000 pages of searchable technical content, including links to products, technologies, solutions, technical tips, tools, and lots more. Registered Cisco.com users can log in from this page to access even more content.

http://www.cisco.com/public/support/tac/home.shtml


Command Reference

The following new and modified commands are pertinent to this feature. To see the command pages for these commands and other commands used with this feature, go to the Cisco IOS Master Commands List, Release 12.4, at http://www.cisco.com/univercd/cc/td/doc/product/software/ios124/124mindx/
124index.htm.

•bantam-jack enable

•card type

•channel-group

•controller

•pri-group

Glossary

AIS—T1 alarm indication signal.

AMI—alternate mark inversion. A bipolar return to zero line encoding scheme.

ANSI T1.403-1995—Network to Customer Installation—DS1 Metallic Interface.

ATM—Asynchronous Transfer Mode.

BERT—bit error rate tester.

BPV—bipolar violation (AMI) same polarity as previous pulse.

CAS—channel-associated signaling.

CCC—clear channel capability (64 kbps data channels for DS1).

CRC—cyclic redundancy check.

CSM—call switching module.

CSU—channel service unit.

DSP—digital signal processor.

DSU—data service unit.

E1—European equivalent of T1, 32 channels of 64 kHz each, 1 for framing, 1 for signaling.

ESF—extended super frame, 24 frames per ESF, includes additional signaling.

FAS—frame align signal.

FDL—facilities data link.

FPGA—field programmable gate array.

HDB3—high density binary 3 zero suppression.

HDLC—High-Level Data Link Control protocol.

LCV—line code violation—occurrence of BPV.

LIU—line interface unit.

LOS—loss of signal.

MARS—modular access routers.

MIB—Management Information Base.

OOF—out of frame (G.706) Consecutive frame alignment signals received in error.

PCI—peripheral component interconnect. Specification that defines the PCI local bus.

PCV—path code violation—(unframed) frame sync bit error, (framed) CRC.

PRI—Primary Rate Interface.

SES—severely errored second.

SF—Super frame, or D4 framing, 12 frames per super frame for in-band signaling extraction.

T1—North American channelized TDM with 24 channels of 64 kHz each plus 8 kHz frame.

Note Refer to the Internetworking Terms and Acronyms for terms not included in this glossary.

© 2003 Cisco Systems, Inc. All rights reserved.