Cisco IOS Software Releases 12.4 Special and Early Deployments

Table Of Contents

Command Reference

aaa accounting network

aaa accounting update

aaa authentication

clear wimax agw bs

clear wimax agw redundancy statistics

clear wimax agw subscriber

data-delivery-service

debug ip slb

debug condition

debug eap

debug eap authenticator

debug ip packet

debug ip slb

debug radius

debug wimax agw aaa

debug wimax agw message

debug wimax agw message tlv

debug wimax agw path

debug wimax agw r6 flow

debug wimax agw r6 session

debug wimax agw r6 subscriber

debug wimax agw redundancy

debug wimax agw switching

debug wimax agw vtemplate

dhcp gateway address

direction

encapsulation agw

ip access-group

ip address allocation subscriber timeout

maximum-latency

maximum-traffic-burst

maximum-traffic-rate-sustained

media-flow-type

minimum-traffic-rate-reserved

pak-classify-rule

policy-transmission-request

priority permit

qos-info

radius-server vsa send accounting wimax

radius-server vsa send authentication wimax

reduced-resources-code

reference-point r6

reference-point r6 response retransmits

reference-point r6 response timeout

sdu-size

security subscriber address-filtering ingress

service-flow pre-defined profile

set

service wimax agw

show ip slb sessions

show wimax agw

show wimax agw message

show wimax agw path

show wimax agw redundancy

show wimax agw statistics

show wimax agw subscriber

show wimax agw tlv

show wimax agw user-group

subscriber redundancy rate

timeout idle

timeout session

tolerated-jitter

traffic-priority

unsolicited-interval-grant

unsolicited-interval-polling

user-group (user group list configuration subcommand)

vrf (user group configuration submode)

wimax agw base-station group

wimax agw base-station ip-addr any group

wimax agw r6 maximum base-station

wimax agw r6 maximum subscriber

wimax agw redundancy

wimax agw service-flow pak-classify-rule profile

wimax agw service-flow profile

wimax agw service-flow profile qos-info

wimax agw user group-list

Command Reference

---

13 September 2007

The following commands are new or changed in Cisco ASN GW 1.0 for IOS Release 12.4(15)XL:

•aaa accounting network

•aaa accounting update

•aaa authentication

•clear wimax agw bs

•clear wimax agw redundancy statistics

•clear wimax agw subscriber

•data-delivery-service

•debug ip slb

•debug condition

•debug eap

•debug eap authenticator

•debug ip packet

•debug ip slb

•debug radius

•debug radius

•debug wimax agw aaa

•debug wimax agw message

•debug wimax agw message tlv

•debug wimax agw path

•debug wimax agw r6 flow

•debug wimax agw r6 session

•debug wimax agw r6 subscriber

•debug wimax agw redundancy

•debug wimax agw switching

•debug wimax agw vtemplate

•dhcp gateway address

•direction

•direction

•encapsulation agw

•ip access-group

•ip address allocation subscriber timeout

•maximum-latency

•maximum-traffic-burst

•maximum-traffic-rate-sustained

•media-flow-type

•minimum-traffic-rate-reserved

•pak-classify-rule

•policy-transmission-request

•priority permit

•qos-info

•radius-server vsa send accounting wimax

•radius-server vsa send authentication wimax

•reduced-resources-code

•reference-point r6

•reference-point r6 response retransmits

•reference-point r6 response timeout

•sdu-size

•security subscriber address-filtering ingress

•service-flow pre-defined profile

•set

•service wimax agw

•show ip slb sessions

•show wimax agw

•show wimax agw message

•show wimax agw path

•show wimax agw redundancy

•show wimax agw statistics

•show wimax agw subscriber

•show wimax agw tlv

•show wimax agw user-group

•subscriber redundancy rate

•timeout idle

•timeout session

•tolerated-jitter

•traffic-priority

•unsolicited-interval-grant

•unsolicited-interval-polling

•user-group (user group list configuration subcommand)

•vrf (user group configuration submode)

•wimax agw base-station group

•wimax agw base-station ip-addr any group

•wimax agw r6 maximum base-station

•wimax agw r6 maximum subscriber

•wimax agw redundancy

•wimax agw service-flow pak-classify-rule profile

•wimax agw service-flow profile

•wimax agw service-flow profile qos-info

•wimax agw user group-list

aaa accounting network

To enable authentication, authorization, and accounting (AAA) accounting of requested services for billing or security purposes when you use RADIUS or TACACS+, use the aaa accounting command in global configuration mode. To disable AAA accounting, use the no form of this command.

aaa accounting {auth-proxy | system | network | exec | connection | commands level | dot1x} {default | list-name} [vrf vrf-name] {start-stop | stop-only | none} [broadcast] group group-name

no aaa accounting {auth-proxy | system | network | exec | connection | commands level | dot1x} {default | list-name} [vrf vrf-name] {start-stop | stop-only | none} [broadcast] group group-name

Syntax Description

auth-proxy	Provides information about all authenticated-proxy user events.
system	Performs accounting for all system-level events not associated with users, such as reloads. Note When system accounting is used and the accounting server is unreachable at system startup time, the system will not be accessible for approximately two minutes.
network	Runs accounting for all network-related service requests, including Serial Line Internet Protocol (SLIP), PPP, PPP Network Control Protocols (NCPs), and AppleTalk Remote Access Protocol (ARAP).
exec	Runs accounting for the EXEC shell session. This keyword might return user profile information such as what is generated by the autocommand command.
connection	Provides information about all outbound connections made from the network access server, such as Telnet, local-area transport (LAT), TN3270, packet assembler and disassembler (PAD), and rlogin.
commands level	Runs accounting for all commands at the specified privilege level. Valid privilege level entries are integers from 0 through 15.
dot1x	Provides information about all IEEE 802.1x-related user events.
default	Uses the listed accounting methods that follow this keyword as the default list of methods for accounting services.
list-name	Character string used to name the list of at least one of the following accounting methods: •group radius—Uses the list of all RADIUS servers for authentication as defined by the aaa group server radius command. •group tacacs+—Uses the list of all TACACS+ servers for authentication as defined by the aaa group server tacacs+ command. •group group-name—Uses a subset of RADIUS or TACACS+ servers for accounting as defined by the server group group-name argument.
vrf vrf-name	(Optional) Specifies a virtual routing and forwarding (VRF) configuration. VRF is used only with system accounting.
start-stop	Sends a "start" accounting notice at the beginning of a process and a "stop" accounting notice at the end of a process. The "start" accounting record is sent in the background. The requested user process begins regardless of whether the "start" accounting notice was received by the accounting server.
stop-only	Sends a "stop" accounting notice at the end of the requested user process.
none	Disables accounting services on this line or interface.
broadcast	(Optional) Enables sending accounting records to multiple AAA servers. Simultaneously sends accounting records to the first server in each group. If the first server is unavailable, failover occurs using the backup servers defined within that group.
group group-name	Specifies the accounting method list. Enter at least one of the following keywords: •auth-proxy—Creates a method list to provide accounting information about all authenticated hosts that use the authentication proxy service. •commands—Creates a method list to provide accounting information about specific, individual EXEC commands associated with a specific privilege level. •connection—Creates a method list to provide accounting information about all outbound connections made from the network access server. •exec—Creates a method list to provide accounting records about user EXEC terminal sessions on the network access server, including username, date, and start and stop times. •network—Creates a method list to provide accounting information for SLIP, PPP, NCPs, and ARAP sessions. •resource—Creates a method list to provide accounting records for calls that have passed user authentication or calls that failed to be authenticated. •tunnel—Creates a method list to provide accounting records (Tunnel-Start, Tunnel-Stop, and Tunnel-Reject) for virtual private dialup network (VPDN) tunnel status changes. •tunnel-link—Creates a method list to provide accounting records (Tunnel-Link-Start, Tunnel-Link-Stop, and Tunnel-Link-Reject) for VPDN tunnel-link status changes.

Defaults

AAA accounting is disabled.

Command Modes

Global configuration (config)

Command History

Release	Modification
10.3	This command was introduced.
12.0(5)T	Group server support was added.
12.1(1)T	The broadcast keyword was introduced on the Cisco AS5300 and Cisco AS5800 universal access servers.
12.1(5)T	The auth-proxy keyword was added.
12.2(1)DX	The vrf keyword and vrf-name argument were introduced on the Cisco 7200 series and Cisco 7401ASR.
12.2(2)DD	This command was integrated into Cisco IOS Release 12.2(2)DD.
12.2(4)B	This command was integrated into Cisco IOS Release 12.2(4)B.
12.2(13)T	The vrf keyword and vrf-name argument were integrated into Cisco IOS Release 12.2(13)T.
12.2(15)B	The tunnel and tunnel-link accounting methods were introduced.
12.3(4)T	The tunnel and tunnel-link accounting methods were integrated into Cisco IOS Release 12.3(4)T.
12.2(28)SB	This command was integrated into Cisco IOS Release 12.2(28)SB.
12.2(33)SRA	This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.4(11)T	The dot1x keyword was integrated into Cisco IOS Release 12.4(11)T.
12.2(33)SXH	This command was integrated into Cisco IOS release 12.(33)SXH.

Usage Guidelines

General Information

Use the aaa accounting command to enable accounting and to create named method lists that define specific accounting methods on a per-line or per-interface basis.

Table 6 contains descriptions of keywords for AAA accounting methods.

Table 6 aaa accounting Methods 

Keyword	Description
group radius	Uses the list of all RADIUS servers for authentication as defined by the aaa group server radius command.
group tacacs+	Uses the list of all TACACS+ servers for authentication as defined by the aaa group server tacacs+ command.
group group-name	Uses a subset of RADIUS or TACACS+ servers for accounting as defined by the server group group-name argument.

In Table 6, the group radius and group tacacs+ methods refer to a set of previously defined RADIUS or TACACS+ servers. Use the radius-server host and tacacs-server host commands to configure the host servers. Use the aaa group server radius and aaa group server tacacs+ commands to create a named group of servers.

Cisco IOS software supports the following two methods of accounting:

•RADIUS—The network access server reports user activity to the RADIUS security server in the form of accounting records. Each accounting record contains accounting attribute-value (AV) pairs and is stored on the security server.

•TACACS+—The network access server reports user activity to the TACACS+ security server in the form of accounting records. Each accounting record contains accounting AV pairs and is stored on the security server.

Method lists for accounting define the way accounting will be performed. Named accounting method lists enable you to designate a particular security protocol to be used on specific lines or interfaces for particular types of accounting services. Create a list by entering values for the list-name argument where list-name is any character string used to name this list (excluding the names of methods, such as RADIUS or TACACS+) and method list keywords to identify the methods to be tried in sequence as given.

If the aaa accounting command for a particular accounting type is issued without a named method list specified, the default method list is automatically applied to all interfaces or lines (where this accounting type applies) except those that have a named method list explicitly defined. (A defined method list overrides the default method list.) If no default method list is defined, then no accounting takes place.

---

Note System accounting does not use named accounting lists; you can define the default list only for system accounting.

---

For minimal accounting, include the stop-only keyword to send a "stop" record accounting notice at the end of the requested user process. For more accounting, you can include the start-stop keyword, so that RADIUS or TACACS+ sends a "start" accounting notice at the beginning of the requested process and a "stop" accounting notice at the end of the process. Accounting is stored only on the RADIUS or TACACS+ server. The none keyword disables accounting services for the specified line or interface.

To specify an accounting configuration for a particular VRF, specify a default system accounting method list, and use the vrf keyword and vrf-name argument. System accounting does not have knowledge of VRF unless specified.

When AAA accounting is activated, the network access server monitors either RADIUS accounting attributes or TACACS+ AV pairs pertinent to the connection, depending on the security method you have implemented. The network access server reports these attributes as accounting records, which are then stored in an accounting log on the security server. For a list of supported RADIUS accounting attributes, see the appendix "RADIUS Attributes" in the Cisco IOS Security Configuration Guide. For a list of supported TACACS+ accounting AV pairs, see the appendix "TACACS+ Attribute-Value Pairs" in the Cisco IOS Security Configuration Guide.

---

Note This command cannot be used with TACACS or extended TACACS.

---

Cisco Service Selection Gateway Broadcast Accounting

To configure Cisco Service Selection Gateway (SSG) broadcast accounting, use ssg_broadcast_accounting for the list-name argument. For more information about configuring SSG, see the chapter "Configuring Accounting for SSG" in the Cisco IOS Service Selection Gateway Configuration Guide, Release 12.4.

Layer 2 LAN Switch Port

You must configure the RADIUS server to perform accounting tasks, such as logging start, stop, and interim-update messages and time stamps. To turn on these functions, enable logging of "Update/Watchdog packets from this AAA client" in your RADIUS server Network Configuration tab. Next, enable "CVS RADIUS Accounting" in your RADIUS server System Configuration tab.

You must enable AAA before you can enter the aaa accounting command. To enable AAA and 802.1X (port-based authentication), use the following global configuration mode commands:

•aaa new-model

•aaa authentication dot1x default group radius

•dot1x system-auth-control

Use the show radius statistics command to display the number of RADIUS messages that do not receive the accounting response message.

Examples

The following example defines a default commands accounting method list, where accounting services are provided by a TACACS+ security server, set for privilege level 15 commands with a stop-only restriction.

aaa accounting commands 15 default stop-only group tacacs+

The following example defines a default auth-proxy accounting method list, where accounting services are provided by a TACACS+ security server with a start-stop restriction. The aaa accounting command activates authentication proxy accounting.

aaa new-model

aaa authentication login default group tacacs+

aaa authorization auth-proxy default group tacacs+

aaa accounting auth-proxy default start-stop group tacacs+

The following example defines a default system accounting method list, where accounting services are provided by RADIUS security server "server1" with a start-stop restriction. The aaa accounting command specifies accounting for vrf "vrf1."

aaa accounting system default vrf1 water start-stop group server1

The following example defines a default IEEE 802.1x accounting method list, where accounting services are provided by a RADIUS server. The aaa accounting command activates IEEE 802.1x accounting.

aaa new model

aaa authentication dot1x default group radius

aaa authorization dot1x default group radius

aaa accounting dot1x default start-stop group radius

The following example shows how to enable network accounting and send tunnel and tunnel-link accounting records to the RADIUS server. (Tunnel-Reject and Tunnel-Link-Reject accounting records are automatically sent if either start or stop records are configured.)

aaa accounting network tunnel start-stop group radius

aaa accounting network session start-stop group radius

The following example shows how to enable IEEE 802.1x accounting:

aaa accounting dot1x default start-stop group radius

aaa accounting system default start-stop group radius

Related Commands

Command	Description
aaa authentication dot1x	Specifies one or more AAA methods for use on interfaces running IEEE 802.1X.
aaa authentication ppp	Specifies one or more AAA authentication methods for use on serial interfaces running PPP.
aaa authorization	Sets parameters that restrict user access to a network.
aaa group server radius	Groups different RADIUS server hosts into distinct lists and distinct methods.
aaa group server tacacs+	Groups different server hosts into distinct lists and distinct methods.
aaa new-model	Enables the AAA access control model.
dot1x system-auth-control	Enables port-based authentication.
radius-server host	Specifies a RADIUS server host.
show radius statistics	Displays the RADIUS statistics for accounting and authentication packets.
tacacs-server host	Specifies a TACACS+ server host.

aaa accounting update

To enable periodic interim accounting records to be sent to the accounting server, use the aaa accounting update command in global configuration mode. To disable interim accounting updates, use the no form of this command.

aaa accounting update [newinfo] [periodic number [jitter {maximum max-value}]]

no aaa accounting update

Syntax Description

newinfo	(Optional) An interim accounting record is sent to the accounting server whenever there is new accounting information to report relating to the user in question.
periodic	(Optional) An interim accounting record is sent to the accounting server periodically, as defined by the number.
number	(Optional) Integer specifying number of minutes.
jitter	(Optional) Allows you to set the maximum jitter value in periodic accounting.
maximum max-value	The number of seconds to set for maximum jitter in periodic accounting. The value 0 turns off jitter. Jitter is set to 300 seconds (5 minutes) by default.

Defaults

Disabled

Command Modes

Global configuration

Command History

Release	Modification
11.3	This command was introduced.
12.2(13)T	Introduced support for generation of an additional updated interim accounting record that contains all available attributes when a call leg is connected.
12.2(15)T11	The jitter keyword was added.
12.2(33)SRA	This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX	This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
12.4(15)XL	This command was incorporated into Cisco IOS Release 12.4(15)XL.

Usage Guidelines

•When the aaa accounting update command is activated, the Cisco IOS software issues interim accounting records for all users on the system. If the newinfo keyword is used, interim accounting records will be sent to the accounting server every time there is new accounting information to report. An example would be when IP Control Protocol (IPCP) completes IP address negotiation with the remote peer. The interim accounting record will include the negotiated IP address used by the remote peer.

•When the gw-accounting aaa command and the aaa accounting update newinfo command and keyword are activated, Cisco IOS software generates and sends an additional updated interim accounting record to the accounting server when a call leg is connected. All attributes (for example, h323-connect-time and backward-call-indicators (BCI)) available at the time of call connection are sent through this interim updated accounting record.

•When used with the periodic keyword, interim accounting records are sent periodically as defined by the number. The interim accounting record contains all of the accounting information recorded for that user up to the time the accounting record is sent.

•When using both the newinfo and periodic keywords, interim accounting records are sent to the accounting server every time there is new accounting information to report, and accounting records are sent to the accounting server periodically as defined by the number. For example, if you configure the aaa accounting update newinfo periodic number command, all users currently logged in will continue to generate periodic interim accounting records while new users will generate accounting records based on the newinfo algorithm.

•Vendor-specific attributes (VSAs) such as h323-connect-time and backward-call-indicator (BCI) are transmitted in the interim update RADIUS message when the aaa accounting update newinfo command and keyword are enabled.

•Jitter is used to provide an interval of time between records so that the AAA server does not get overwhelmed by a constant stream of records. If certain applications require that periodic records be sent a exact intervals, you should disable jitter by setting it to 0.

---

Caution Using the aaa accounting update periodic command and keyword can cause heavy congestion when many users are logged into the network.

---

Examples

The following example sends PPP accounting records to a remote RADIUS server. When IPCP completes negotiation, this command sends an interim accounting record to the RADIUS server that includes the negotiated IP address for this user; it also sends periodic interim accounting records to the RADIUS server at 30-minute intervals.

aaa accounting network default start-stop group radius

aaa accounting update newinfo periodic 30

The following example sends periodic interim accounting records to the RADIUS server at 30-minute intervals and disables jitter:

aaa accounting update newinfo periodic 30 jitter maximum 0

Related Commands

Command	Description
aaa accounting	Enables AAA accounting of requested services for billing or security purposes.
gw-accounting aaa	Enables VoIP gateway accounting through the AAA system.

aaa authentication

To specify one or more authentication, authorization, and accounting (AAA) methods for use on interfaces running IEEE 802.1X, use the aaa authentication dot1x command in global configuration mode. To disable authentication, use the no form of this command

aaa authentication dot1x {default | listname} method1 [method2...]

no aaa authentication dot1x {default | listname} method1 [method2...]

Syntax Description

default	Uses the listed authentication methods that follow this argument as the default list of methods when a user logs in.
listname	Character string used to name the list of authentication methods tried when a user logs in.
method1 [method2...]	At least one of these keywords: •enable—Uses the enable password for authentication. •group radius—Uses the list of all RADIUS servers for authentication. •line—Uses the line password for authentication. •local—Uses the local username database for authentication. •local-case—Uses the case-sensitive local username database for authentication. •none—Uses no authentication. The client is automatically authenticated by the switch without using the information supplied by the client.

Defaults

No authentication is performed.

Command Types

Global configuration

Command History

Release	Modification
12.1(6)EA2	This command was introduced for the Cisco Ethernet switch network module.
12.2(15)ZJ	This command was implemented on the following platforms for the Cisco Ethernet Switch Module: Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series.
12.3(2)XA	This command was introduced on the following Cisco router platforms: Cisco 806, Cisco 831, Cisco 836, Cisco 837, Cisco 1701, Cisco 1710, Cisco 1721, Cisco 1751-V, and Cisco 1760.
12.3(4)T	This command was integrated into Cisco IOS Release 12.3(4)T. Router support was added for the following platforms: Cisco 1751, Cisco 2610XM - Cisco 2611XM, Cisco 2620XM - Cisco 2621XM, Cisco 2650XM - Cisco 2651XM, Cisco 2691, Cisco 3640, Cisco 3640A, and Cisco 3660.
12.2(33)SRA	This command was integrated into Cisco IOS Release 12.2(33)SRA
12.2SX	This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
12.4(15)XL	This command was integrated into Cisco IOS Release 12.5(15)YX.

Usage Guidelines

The method argument identifies the list of methods that the authentication algorithm tries in the given sequence to validate the password provided by the client. The only method that is truly 802.1X-compliant is the group radius method, in which the client data is validated against a RADIUS authentication server. The remaining methods enable AAA to authenticate the client by using locally configured data. For example, the local and local-case methods use the username and password that are saved in the Cisco IOS configuration file. The enable and line methods use the enable and line passwords for authentication.

If you specify group radius, you must configure the RADIUS server by entering the radius-server host global configuration command. If you are not using a RADIUS server, you can use the local or local-case methods, which access the local username database to perform authentication. By specifying the enable or line methods, you can supply the clients with a password to provide access to the switch.

Use the show running-config privileged EXEC command to display the configured lists of authentication methods.

Examples

The following example shows how to create an authentication list. This authentication first tries to contact a RADIUS server. If this action returns an error, the user is allowed access with no authentication:

service wimax agw

aaa new-model

!

!

aaa authentication dot1x agw group radius

aaa authorization network default group radius 

aaa accounting update periodic 1

aaa accounting network agw start-stop group radius

!

!

aaa session-id unique

clock timezone PST -8

clock calendar-valid

Related Commands

Command	Description
debug dot1x	Displays 802.1X debugging information.
identity profile default	Creates an identity profile and enters dot1x profile configuration mode.
show dot1x	Displays details for an identity profile.
show dot1x (EtherSwitch)	Displays 802.1X statistics, administrative status, and operational status for the switch or for the specified interface.

clear wimax agw bs

To clear all the subscribers that belong to this base station, and clear the base station details, use the clear wimax agw bs command in global configuration mode.

clear wimax agw bs bs-ip-address

Syntax Description

bs-ip-address

IP address of a specific base station.

Defaults

There are no default values.

Command Modes

Privileged EXEC

Usage Guidelines

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

---

Note All clear wimax commands are valid only on the SR ACTIVE card.

---

For example:

asngw#clear wimax agw subscriber all

This is STANDBY unit. This command must be issued on the ACTIVE unit

Examples

The following example illustrates how to enable the clear wimax agw bs command:

router#clear wimax agw bs bs-ip-address

clear wimax agw redundancy statistics

To clear redundancy specific statistics, use the clear wimax agw redundancy statistics command in global configuration mode.

clear wimax agw redundancy statistics

Syntax Description

This command has no keywords or arguments.

Defaults

There are no default values.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

---

Note All clear wimax commands are valid only on the SR ACTIVE card.

---

For example:

asngw#clear wimax agw subscriber all

This is STANDBY unit. This command must be issued on the ACTIVE unit

Examples

The following example clears all ASN GW redundancy statistics:

router#clear wimax agw redundancy statistics

clear wimax agw subscriber

To clear the subscriber on the AGW, use the clear wimax agw subscriber command in global configuration mode.

clear wimax agw subscriber [mac-id mac-id ] [local]

Syntax Description

mac-id mac-id	Specifies the MAC ID of the subscriber. If the MACID is not specified the entire subscriber list is cleared.
local	If the local keyword is configured, the subscribers are cleared locally, otherwise de-registration is sent to the base station.

Defaults

There are no default values.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

---

Note All clear wimax commands are valid only on the SR ACTIVE card.

---

For example:

asngw#clear wimax agw subscriber all

This is STANDBY unit. This command must be issued on the ACTIVE unit

Examples

The following example clears subscribers locally:

clear wimax agw subscriber local

data-delivery-service

To configure data delivery service associated with certain predefined set of QoS-related service flow parameters, use the data-delivery-service command in global configuration mode. Use the no form of the command to disable this feature.

data-delivery-service {unsolicited-grant | real-time-variable-rate | non-real-time-variable-rate | best-effort | extended-real-time-variable-rate}

no data-delivery-service

Syntax Description

unsolicited-grant	Configures the unsolicited grant.
real-time-variable- rate	Cofigures the real time variable rate.
non-real-time-variable-rate	Configures the non-real time variable rate.
best-effort	Configures the best effort.
extended-real-time- variable-rate	Configures the extended real time variable rate.

Defaults

The default setting is unsolicited-grant.

Command Modes

Service flow QoS info configuration mode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example illustrates how to configure the data-delivery-service command:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

wimax agw service-flow qos-info profile isf-qos-uplink  

 data-delivery-service unsolicited-grant  

 maximum-latency 11  

 maximum-traffic-burst 21  

 maximum-traffic-rate-sustained 31  

 minimum-traffic-rate-reserved 41  

 policy-transmission-request 51  

 sdu-size 61  

 tolerated-jitter 71  

 traffic-priority 3  

 unsolicited-interval-grant 81  

 unsolicited-interval-polling 91

! 

wimax agw service-flow qos-info profile downlink-qos-02  

 data-delivery-service real-time-variable-rate  

 media-flow-type 05abcd 

debug ip slb

To display debugging messages for the Cisco IOS Server Load Balancing (SLB) feature, use the debug ip slb command in privileged EXEC mode. To disable debug output, use the no form of this command.

debug ip slb {conns | dfp | icmp | reals | asnr6 | all}

no debug ip slb {conns | dfp | icmp | reals | asnr6 | all}

Syntax Description

conns	Displays debugging messages for all connections being handled by Cisco IOS SLB.
dfp	Displays debugging messages for the Cisco IOS SLB DFP and DFP agents.
icmp	Displays all ICMP debugging messages for Cisco IOS SLB.
reals	Displays debugging messages for all real servers defined to Cisco IOS SLB.
asnr6	Displays debugging messages for the packet path inside ASNLB.
all	Displays all debugging messages for Cisco IOS SLB.

Command Default

No default behavior or values

Command Modes

Privileged Exec

Command History

Release	Modification
12.0(7)XE	This command was introduced.
12.1(5)T	This command was integrated into Cisco IOS Release 12.1(5)T.
12.4(15)XL	The asnr6 keyword was introduced.

Usage Guidelines

See the following caution before using debug commands.

---

Caution Because debugging output is assigned high priority in the CPU process, it can render the system unusable. For this reason, only use debug commands to troubleshoot specific problems or during troubleshooting sessions with Cisco technical support staff. Moreover, it is best to use debug commands during periods of lower network flows and fewer users. Debugging during these periods reduces the effect these commands have on other users on the system.

---

Examples

Here is an example of the command:

Router# debug ip slb all

SLB All debugging is on

Router# 

The following example stops all debugging: 

Router# no debug all

All possible debugging has been turned off

debug condition

To enable conditional debugging on the ASN GW, use the debug condition command in privileged EXEC mode.

debug condition [mac-address mac-id-of-subscriber] [ip bs-ip-address]

Syntax Description

mac-address mac-id-of-subscriber]	based on the Subscriber MAC-ID
ip bs-ip-address	based on the BS IP address

Defaults

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

When there is option to branch in the debug CLI, all the options after the keyword can be enabled by using the carriage-return. For example:

To enable all the WiMAX AGW related debugs, enter:

router#debug wimax agw

To enable all the WiMAX AGW session related debugs, enter:

router#debug wimax agw session

Examples

The following example enables conditional debugging on the ASN GW:

Router#debug condition mac-address mac-id-of-subscriber

Rotuer#debug condition ip bs-ip-address

debug eap

To display debug output for EAP related events and errors, use the debug eap command in privileged EXEC mode. Use the no version of command to turn off debug output.

debug eap {all | authenticator | errors | events | packets | peer | sm}

no debug eap {all | authenticator | errors | events | packets | peer | sm}

Syntax Description

all	Displays all eap debug information.
authenticator	Displays only authenticator errors.
errors	Displays eap errors.
events	Displays eap events.
packets	Displays eap packet information
peer	Displays only peer errors.
sm	Displays EAP state machine errors.

Defaults

No default values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

Here is sample output for thedebug eap events command:

Router#debug eap events

EAP authenticator events debugging is on

EAP peer events debugging is on

Router# 

*Feb 22 08:58:46.351: EAP-EVENT: Received context create from lower layer (0x59000003)

*Feb 22 08:58:46.351: EAP-AUTH-EVENT: Received AAA ID 0x00000005 from LL

*Feb 22 08:58:46.351: EAP-AUTH-AAA-EVENT: Assigning AAA ID 0x00000005

*Feb 22 08:58:46.351: EAP-EVENT: Allocated new EAP context (handle = 0xB4000003)

*Feb 22 08:58:46.351: EAP-EVENT: Received event 'EAP_AUTHENTICATOR_START' on handle 
0xB4000003

*Feb 22 08:58:46.351: EAP-AUTH-EVENT: Current method = Identity

*Feb 22 08:58:46.351: EAP-AUTH-EVENT: Sending packet to lower layer for context 0xB4000003

*Feb 22 08:58:46.351: EAP-EVENT: Started 'Authenticator ReqId Retransmit' timer (5s) for 
EAP sesion handle 0xB4000003

*Feb 22 08:58:46.351: EAP-EVENT: Started EAP tick timer

*Feb 22 08:58:46.351: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 
0xB4000003

*Feb 22 08:58:46.355: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0xB4000003

*Feb 22 08:58:46.355: EAP-AUTH-EVENT: EAP Response received by context

asn# 0xB4000003

*Feb 22 08:58:46.355: EAP-AUTH-EVENT: EAP Response type = Identity

*Feb 22 08:58:46.355: EAP-EVENT: Stopping 'Authenticator ReqId Retransmit' timer for EAP 
sesion handle 0xB4000003

*Feb 22 08:58:46.355: EAP-AUTH-EVENT: Received peer identity: swimeap@wimax.org

*Feb 22 08:58:46.355: EAP-EVENT: Sending lower layer event 'EAP_GET_AAA_METHOD_LISTS' on 
handle 0xB4000003

*Feb 22 08:58:46.355: EAP-EVENT: Sending lower layer event 'EAP_GET_PEER_MAC_ADDRESS' on 
handle 0xB4000003

*Feb 22 08:58:46.355: EAP-EVENT: Sending lower layer event 'EAP_CUSTOMIZE_AAA_REQUEST' on 
handle 0xB4000003

*Feb 22 08:58:46.355: EAP-AUTH-AAA-EVENT: Request sent successfully

*Feb 22 08:58:46.359: EAP-EVENT: eap_aaa_reply

*Feb 22 08:58:46.359: EAP-AUTH-AAA-EVENT: Server status: GET_CHALLENGE_RESPONSE

*Feb 22 08:58:46.359: EAP-EVENT: Received event 'EAP_AAA_RX_PACKET' on handle 0xB4000003

*Feb 22 08:58:46.359: EAP-AUTH-EVENT: Current method = 13

*Feb 22 08:58:46.359: EAP-AUTH-EVENT: Sending packet to lower layer

for context 0xB4000003

*Feb 22 08:58:46.359: EAP-EVENT: Started 'Authenticator Retransmit' timer (5s) for EAP 
sesion handle 0xB4000003

*Feb 22 08:58:46.359: EAP-EVENT: Started EAP tick timer

*Feb 22 08:58:46.359: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 
0xB4000003

Router#

Router#

*Feb 22 08:58:51.479: EAP-EVENT: 'Authenticator Retransmit' timer expired for EAP sesion 
handle 0xB4000003

*Feb 22 08:58:51.479: EAP-AUTH-EVENT: Resending last packet for context 0xB4000003

*Feb 22 08:58:51.479: EAP-AUTH-EVENT: Sending packet to lower layer for context 0xB4000003

*Feb 22 08:58:51.479: EAP-EVENT: Started 'Authenticator Retransmit' timer (5s) for EAP 
sesion handle

*Feb 22 08:59:11.959: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 
0xB4000003

*Feb 22 08:59:11.959: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0xB4000003

*Feb 22 08:59:11.959: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 
0xB4000003

Router#

*Feb 22 08:59:17.079: EAP-EVENT: 'Authenticator Retransmit' timer expired for EAP sesion 
handle 0xB4000003

*Feb 22 08:59:17.079: EAP-EVENT: Sending lower layer event 'EAP_TIMEOUT' on handle 
0xB4000003

*Feb 22 08:59:17.079: EAP-EVENT: Received free context (0xB4000003) from lower layer

*Feb 22 08:59:17.079: EAP-EVENT: Received event 'EAP_DELETE' on handle 0xB4000003

*Feb 22 08:59:17.079: EAP-AUTH-EVENT: Freed EAP auth context

*Feb 22 08:59:17.079: EAP-EVENT: Freed EAP context

asn#

*Feb 22 08:59:18.103: EAP-EVENT: Stopped EAP tick timer

debug eap authenticator

To display debug output for EAP authenticator related events and errors, use the debug eap authenticator command in privileged EXEC mode. Use the no version of command to turn off debug output.

debug eap authenticator {all | errors | events | packets | sm}

no debug eap authenticator {all | errors | events | packets | sm}

Syntax Description

all	Displays all eap debug information.
errors	Displays eap errors.
events	Displays eap events.
packets	Displays eap packet information
sm	Displays EAP state machine errors.

Defaults

There are no default values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

Here is sample output for thedebug eap authenticator errors command:

Router#debug eap authenticator errors 

EAP authenticator errors debugging is on

Router#

*Feb 23 07:30:09.546: EAP-AUTH-ERROR: Invalid response id 2 (current id = 3)

Here is sample output for thedebug eap authenticator events command:

Router#debug eap authenticator events

EAP authenticator events debugging is on

Router#

*Feb 23 07:36:08.258: EAP-EVENT: Received context create from lower layer (0x67000006)

*Feb 23 07:36:08.258: EAP-AUTH-EVENT: Received AAA ID 0x00000009 from LL

*Feb 23 07:36:08.258: EAP-AUTH-AAA-EVENT: Assigning AAA ID 0x00000009

*Feb 23 07:36:08.258: EAP-EVENT: Allocated new EAP context (handle = 0x27000006)

*Feb 23 07:36:08.258: EAP-EVENT: Received event 'EAP_AUTHENTICATOR_START' on handle 
0x27000006

*Feb 23 07:36:08.258: EAP-AUTH-EVENT: Current method = Identity

*Feb 23 07:36:08.258: EAP-AUTH-EVENT: Sending packet to lower layer for context 0x27000006

*Feb 23 07:36:08.258: EAP-EVENT: Started 'Authenticator ReqId Retransmit' timer (5s) for 
EAP sesion handle 0x27000006

*Feb 23 07:36:08.258: EAP-EVENT: Started EAP tick timer

*Feb 23 07:36:08.258: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 
0x27000006

*Feb 23 07:36:08.258: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0x27000006

*Feb 23 07:36:08.258: EAP-AUTH-EVENT: EAP Response received by context

Router# 0x27000006

*Feb 23 07:36:08.258: EAP-AUTH-EVENT: EAP Response type = Identity

*Feb 23 07:36:08.258: EAP-EVENT: Stopping 'Authenticator ReqId Retransmit' timer for EAP 
sesion handle 0x27000006

*Feb 23 07:36:08.258: EAP-AUTH-EVENT: Received peer identity: swimeap@wimax.org

*Feb 23 07:36:08.258: EAP-EVENT: Sending lower layer event 'EAP_GET_AAA_METHOD_LISTS' on 
handle 0x27000006

*Feb 23 07:36:08.258: EAP-EVENT: Sending lower layer event 'EAP_GET_PEER_MAC_ADDRESS' on 
handle 0x27000006

*Feb 23 07:36:08.258: EAP-EVENT: Sending lower layer event 'EAP_CUSTOMIZE_AAA_REQUEST' on 
handle 0x27000006

*Feb 23 07:36:08.258: EAP-AUTH-AAA-EVENT: Request sent successfully

*Feb 23 07:36:08.266: EAP-EVENT: eap_aaa_reply

*Feb 23 07:36:08.266: EAP-AUTH-AAA-EVENT: Server status: GET_CHALLENGE_RESPONSE

*Feb 23 07:36:08.266: EAP-EVENT: Received event 'EAP_AAA_RX_PACKET' on handle 0x27000006

*Feb 23 07:36:08.266: EAP-AUTH-EVENT: Current method = 13

*Feb 23 07:36:08.266: EAP-AUTH-EVENT: Sending packet to lower layer for context 0x27000006

*Feb 23 07:36:08.266: EAP-EVENT: Started 'Authenticator Retransmit' timer (5s) for EAP 
sesion handle 0x27000006

*Feb 23 07:36:08.266: EAP-EVENT: Started EAP tick timer

*Feb 23 07:36:08.266: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 
0x27000006

*Feb 23 07:36:08.274: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0x27000006

*Feb 23 07:36:08.274: EAP-AUTH-EVENT: EAP Response received by context 0x27000006

*Feb 23 07:36:08.274: EAP-AUTH-EVENT: EAP Response type = Method (13)

*Feb 23 07:36:08.274: EAP-EVENT: Stopping 'Authenticator Retransmit' timer for EAP sesion 
handle 0x27000006

*Feb 23 07:36:08.274: EAP-EVENT: Sending lower layer event 'EAP_GET_AAA_METHOD_LISTS' on 
handle 0x27000006

*Feb 23 07:36:08.274: EAP-EVENT: Sending lower layer event 'EAP_CUSTOMIZE_AAA_REQUEST' on 
handle 0x27000006

*Feb 23 07:36:08.274: EAP-AUTH-AAA-EVENT: Request sent successfully

*Feb 23 07:36:08.282: EAP-EVENT: eap_aaa_reply

*Feb 23 07:36:08.282: EAP-AUTH-AAA-EVENT: Server status: GET_CHALLENGE_RESPONSE

*Feb 23 07:36:08.282: EAP-EVENT: Received event 'EAP_AAA_RX_PACKET' on handle 0x27000006

*Feb 23 07:36:08.282: EAP-AUTH-EVENT: Current method = 13

debug ip packet

To display general IP debugging information and IP security option (IPSO) security transactions, use the debug ip packet command in privileged EXEC mode. To disable debugging output, use the no form of this command.

debug ip packet [access-list-number] [detail] [dump]

no debug ip packet [access-list-number]

Syntax Description

access-list-number	(Optional) The IP access list number that you can specify. If the datagram is not permitted by that access list, the related debugging output is suppressed. Standard, extended, and expanded access lists are supported. The range of standard and extended access lists is from 1 to 199. The range of expanded access lists is from 1300 to 2699.
detail	(Optional) Displays detailed IP packet debugging information. This information includes the packet types and codes as well as source and destination port numbers.
dump	(Hidden) Displays IP packet debugging information along with raw packet data in hexadecimal and ASCII forms. This keyword can be enabled with individual access lists and also with the detail keyword. Note The dump keyword is not fully supported and should be used only in collaboration with Cisco Technical Support. See the caution notes below, in the usage guidelines, for more specific information.

Command Modes

Privileged EXEC

Usage Guidelines

If a communication session is closing when it should not be, an end-to-end connection problem can be the cause. The debug ip packet command is useful for analyzing the messages traveling between the local and remote hosts. IP packet debugging captures the packets that are process switched including received, generated and forwarded packets. IP packets that are switched in the fast path are not captured.

IPSO security transactions include messages that describe the cause of failure each time a datagram fails a security test in the system. This information is also sent to the sending host when the router configuration allows it.

---

Caution Because the debug ip packet command generates a substantial amount of output and uses a substantial amount of system resources, this command should be used with caution in production networks. It should only be enabled when traffic on the IP network is low, so other activity on the system is not adversely affected. Enabling the detail and dump keywords use the highest level of system resources of the available configuration options for this command, so a high level of caution should be applied when enabling either of these keywords.

---

---

Caution The dump keyword is not fully supported and should be used only in collaboration with Cisco Technical Support. Because of the risk of using significant CPU utilization, the dump keyword is hidden from the user and cannot be seen using the "?" prompt. The length of the displayed packet information may exceed the actual packet length and include additional padding bytes that do not belong to the IP packet. Also note that the beginning of a packet may start at different locations in the dump output depending on the specific router, interface type, and packet header processing that may have occurred before the output is displayed.

---

Examples

The following is sample output from the debug ip packet command:

Router# debug ip packet

IP packet debugging is on 

IP: s=172.69.13.44 (Fddi0), d=10.125.254.1 (Serial2), g=172.69.16.2, forward

IP: s=172.69.1.57 (Ethernet4), d=10.36.125.2 (Serial2), g=172.69.16.2, forward

IP: s=172.69.1.6 (Ethernet4), d=255.255.255.255, rcvd 2

IP: s=172.69.1.55 (Ethernet4), d=172.69.2.42 (Fddi0), g=172.69.13.6, forward

IP: s=172.69.89.33 (Ethernet2), d=10.130.2.156 (Serial2), g=172.69.16.2, forward

IP: s=172.69.1.27 (Ethernet4), d=172.69.43.126 (Fddi1), g=172.69.23.5, forward

IP: s=172.69.1.27 (Ethernet4), d=172.69.43.126 (Fddi0), g=172.69.13.6, forward

IP: s=172.69.20.32 (Ethernet2), d=255.255.255.255, rcvd 2

IP: s=172.69.1.57 (Ethernet4), d=10.36.125.2 (Serial2), g=172.69.16.2, access denied

The output shows two types of messages that the debug ip packet command can produce; the first line of output describes an IP packet that the router forwards, and the third line of output describes a packet that is destined for the router. In the third line of output, rcvd 2 indicates that the router decided to receive the packet.

Table 7 describes the significant fields shown in the display.

Table 7 debug ip packet Field Descriptions 

Field	Description
IP:	Indicates that this is an IP packet.
s=172.69.13.44 (Fddi0)	Indicates the source address of the packet and the name of the interface that received the packet.
d=10.125.254.1 (Serial2)	Indicates the destination address of the packet and the name of the interface (in this case, S2) through which the packet is being sent out on the network.
g=172.69.16.2	Indicates the address of the next-hop gateway.
forward	Indicates that the router is forwarding the packet. If a filter denies a packet, "access denied" replaces "forward," as shown in the last line of output.

The following is sample output from the debug ip packet command enabled with the detail keyword:

Router# debug ip packet detail 

IP packet debugging is on (detailed)

001556: 19:59:30: CEF: Try to CEF switch 10.4.9.151 from FastEthernet0/0

001557: 19:59:30: IP: s=10.4.9.6 (FastEthernet0/0), d=10.4.9.151 (FastEthernet03

001558: 19:59:30:     TCP src=179, dst=11001, seq=3736598846, ack=2885081910, wH

001559: 20:00:09: CEF: Try to CEF switch 10.4.9.151 from FastEthernet0/0

001560: 20:00:09: IP: s=10.4.9.4 (FastEthernet0/0), d=10.4.9.151 (FastEthernet03

001561: 20:00:09:     TCP src=179, dst=11000, seq=163035693, ack=2948141027, wiH

001562: 20:00:14: CEF: Try to CEF switch 10.4.9.151 from FastEthernet0/0

001563: 20:00:14: IP: s=10.4.9.6 (FastEthernet0/0), d=10.4.9.151 (FastEthernet03

001564: 20:00:14:     ICMP type=8, code=0

001565: 20:00:14: IP: s=10.4.9.151 (local), d=10.4.9.6 (FastEthernet0/0), len 1g

001566: 20:00:14:     ICMP type=0, code=0

The format of the output with detail keyword provides additional information, such as the packet type, code, some field values, and source and destination port numbers.

Table 8 describes the significant fields shown in the display.

Table 8 debug ip packet detail Field Descriptions 

Field	Description
CEF:	Indicates that the IP packet is being processed by CEF.
IP:	Indicates that this is an IP packet.
s=10.4.9.6 (FastEthernet0/0)	Indicates the source address of the packet and the name of the interface that received the packet.
d=10.4.9.151 (FastEthernet03)	Indicates the destination address of the packet and the name of the interface through which the packet is being sent out on the network.
TCP src=	Indicates the source TCP port number.
dst=	Indicates the destination TCP port number.
seq=	Value from the TCP packet sequence number field.
ack=	Value from the TCP packet acknowledgement field.
ICMP type=	Indicates ICMP packet type.
code=	Indicates ICMP return code.

The following is sample output from the debug ip packet command enabled with the dump keyword:

Router# debug ip packet dump

IP packet debugging is on (detailed) (dump)

21:02:42: IP: s=10.4.9.6 (FastEthernet0/0), d=10.4.9.4 (FastEthernet0/0), len 13

07003A00:                       0005 00509C08            ...P..

07003A10: 0007855B 4DC00800 45000064 001E0000  ...[M@..E..d....

07003A20: FE019669 0A040906 0A040904 0800CF7C  ~..i..........O|

07003A30: 0D052678 00000000 0A0B7145 ABCDABCD  ..&x......qE+M+M

07003A40: ABCDABCD ABCDABCD ABCDABCD ABCDABCD  +M+M+M+M+M+M+M+M

07003A50: ABCDABCD ABCDABCD ABCDABCD ABCDABCD  +M+M+M+M+M+M+M+M

07003A60: ABCDABCD ABCDABCD ABCDABCD ABCDABCD  +M+M+M+M+M+M+M+M

07003A70: ABCDABCD ABCDABCD ABCDABCD           +M+M+M+M+M+M    

21:02:42: IP: s=10.4.9.4 (local), d=10.4.9.6 (FastEthernet0/0), len 100, sending

07003A00:                       0005 00509C08            ...P..

07003A10: 0007855B 4DC00800 45000064 001E0000  ...[M@..E..d....

07003A20: FF019569 0A040904 0A040906 0000D77C  ...i..........W|

07003A30: 0D052678 00000000 0A0B7145 ABCDABCD  ..&x......qE+M+M

07003A40: ABCDABCD ABCDABCD ABCDABCD ABCDABCD  +M+M+M+M+M+M+M+M

07003A50: ABCDABCD ABCDABCD ABCDABCD ABCDABCD  +M+M+M+M+M+M+M+M

07003A60: ABCDABCD ABCDABCD ABCDABCD ABCDABCD  +M+M+M+M+M+M+M+M

07003A70: ABCDABCD ABCDABCD ABCDABCD           +M+M+M+M+M+M    

21:02:42: CEF: Try to CEF switch 10.4.9.4 from FastEthernet0/0

21:02:42: IP: s=10.4.9.6 (FastEthernet0/0), d=10.4.9.4 (FastEthernet0/0), len 13

07003380:                       0005 00509C08            ...P..

07003390: 0007855B 4DC00800 45000064 001F0000  ...[M@..E..d....

070033A0: FE019668 0A040906 0A040904 0800CF77  ~..h..........Ow

070033B0: 0D062678 00000000 0A0B7149 ABCDABCD  ..&x......qI+M+M

070033C0: ABCDABCD ABCDABCD ABCDABCD ABCDABCD  +M+M+M+M+M+M+M+M

070033D0: ABCDABCD ABCDABCD ABCDABCD ABCDABCD  +M+M+M+M+M+M+M+M

070033E0: ABCDABCD ABCDABCD ABCDABCD ABCDABCD  +M+M+M+M+M+M+M+M

070033F0: ABCDABCD ABCDABCD ABCDABCD           +M+M+M+M+M+M 

---

Note The dump keyword is not fully supported and should be used only in collaboration with Cisco Technical Support. See the caution in the usage guidelines section of this command reference page for more specific information.

---

The output from the debug ip packet command, when the dump keyword is enabled, provides raw packet data in hexadecimal and ASCII forms. This addtional output is displayed in addition to the standard output. The dump keyword can be used with all of the available configuration options of this command.

Table 9 describes the significant fields shown in the display.

Table 9 debug ip packet dump Field Descriptions 

Field	Description
IP:	Indicates that this is an IP packet.
s=10.4.9.6 (FastEthernet0/0)	Indicates the source address of the packet and the name of the interface that received the packet.
d=10.4.9.4 (FastEthernet0/0) len 13	Indicates destination address and length of the packet and the name of the interface through which the packet is being sent out on the network.
sending	Indicates that the router is sending the packet.

The calculation on whether to send a security error message can be somewhat confusing. It depends upon both the security label in the datagram and the label of the incoming interface. First, the label contained in the datagram is examined for anything obviously wrong. If nothing is wrong, assume the datagram to be correct. If something is wrong, the datagram is treated as unclassified genser. Then the label is compared with the interface range, and the appropriate action is taken, as Table 10 describes.

Table 10 Security Actions  

Classification	Authorities	Action Taken
Too low	Too low Good Too high	No Response No Response No Response
In range	Too low Good Too high	No Response Accept Send Error
Too high	Too low In range Too high	No Response Send Error Send Error

The security code can only generate a few types of Internet Control Message Protocol (ICMP) error messages. The only possible error messages and their meanings follow:

•ICMP Parameter problem, code 0—Error at pointer

•ICMP Parameter problem, code 1—Missing option

•ICMP Parameter problem, code 2—See Note that follows

•ICMP Unreachable, code 10—Administratively prohibited

---

Note The message "ICMP Parameter problem, code 2" identifies a specific error that occurs in the processing of a datagram. This message indicates that the router received a datagram containing a maximum length IP header but no security option. After being processed and routed to another interface, it is discovered that the outgoing interface is marked with "add a security label." Because the IP header is already full, the system cannot add a label and must drop the datagram and return an error message.

---

When an IP packet is rejected due to an IP security failure, an audit message is sent via Department of Defense Intelligence Information System Network Security for Information Exchange (DNSIX) Network Address Translation (NAT). Also, any debug ip packet output is appended to include a description of the reason for rejection. This description can be any of the following:

•No basic

•No basic, no response

•Reserved class

•Reserved class, no response

•Class too low, no response

•Class too high

•Class too high, bad authorities, no response

•Unrecognized class

•Unrecognized class, no response

•Multiple basic

•Multiple basic, no response

•Authority too low, no response

•Authority too high

•Compartment bits not dominated by maximum sensitivity level

•Compartment bits do not dominate minimum sensitivity level

•Security failure: extended security disallowed

•NLESO source appeared twice

•ESO source not found

•Postroute, failed xfc out

•No room to add IPSO

debug ip slb

To display debugging messages for the Cisco IOS Server Load Balancing (SLB) feature, use the debug ip slb command in privileged EXEC mode. To disable debug output, use the no form of this command.To display the packet path inside ASNLB, use the debug ip slb asnr6.

debug ip slb {conns | dfp | icmp | asnr6 | reals | all}

no debug ip slb {conns | dfp | icmp | asnr6 | reals | all}

Syntax Description

conns	Displays debugging messages for all connections being handled by Cisco IOS SLB.
dfp	Displays debugging messages for the Cisco IOS SLB DFP and DFP agents.
icmp	Displays all ICMP debugging messages for Cisco IOS SLB.
asnr6	Displays all ASN GW R6 debugging messages for Cisco IOS SLB.
reals	Displays debugging messages for all real servers defined to Cisco IOS SLB.
all	Displays all debugging messages for Cisco IOS SLB.

Command Default

No default behavior or values.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.0(7)XE	This command was introduced.
12.1(5)T	This command was integrated into Cisco IOS Release 12.1(5)T.
12.4(15)XL	The asnr6 keyword was added.

Usage Guidelines

See the following caution before using debug commands.

---

Caution Because debugging output is assigned high priority in the CPU process, it can render the system unusable. For this reason, only use debug commands to troubleshoot specific problems or during troubleshooting sessions with Cisco technical support staff. Moreover, it is best to use debug commands during periods of lower network flows and fewer users. Debugging during these periods reduces the effect these commands have on other users on the system.

---

Examples

Here is an example of the debug ip slb command:

Router# debug ip slb all

SLB All debugging is on

Router# 

The following example stops all debugging:

Router# no debug all

All possible debugging has been turned off

debug radius

To display debugging output for RADIUS parameters, use the debug radius command in privileged EXEC mode. Use the no version of command to disable this feature.

debug radius {brief | hex}

no debug radius {brief | hex}

Syntax Description

brief	(Optional) Displays abbreviated debug output.
hex	(Optional) Displays debugging output in hexadecimal notation.

Defaults

Debugging output in ASCII format is enabled.

Command Modes

Privileged EXEC.

Command History

Release	Modification
11.2(1)T	This command was introduced.
12.2(11)T	The brief and hex keywords were added. The default output format became ASCII rather than hexadecimal.
12.4(15)XL	This command was integrated into Cisco IOS Release 12.4(15)XL.

Usage Guidelines

RADIUS is a distributed security system that secures networks against unauthorized access. Cisco supports RADIUS under the authentication, authorization, and accounting (AAA) security system. When RADIUS is used on the router, you can use the debug radius command to display detailed debugging and troubleshooting information in ASCII format. Use the debug radius brief command for abbreviated output displaying client/server interaction and minimum packet information. Use the debug radius hex command to display packet dump information that has not been truncated in hex format.

Examples

Here is sample output for the debug radius brief command:

Router#debug radius briefRadius protocol debugging is on

Radius protocol brief debugging is on

Radius protocol verbose debugging is off

Radius packet hex dump debugging is off

Radius packet protocol debugging is off

Radius elog debugging debugging is off

Radius packet retransmission debugging is off

Radius server fail-over debugging is off

Radius elog debugging debugging is off

Router# 

*Feb 22 08:33:03.259: RADIUS/ENCODE(00000002):Orig. component type = DOT1X

*Feb 22 08:33:03.259: RADIUS/ENCODE: NAS PORT sending disabled

*Feb 22 08:33:03.259: RADIUS(00000002): Config NAS IP: 0.0.0.0

*Feb 22 08:33:03.259: RADIUS(00000002): Config NAS IP: 0.0.0.0

*Feb 22 08:33:03.259: RADIUS: Attribute 55 not sent, as system clock is not set

*Feb 22 08:33:03.259: RADIUS/ENCODE: Best Local IP-Address 1.8.84.1 for Radius-Server 
1.8.91.8

*Feb 22 08:33:03.259: RADIUS(00000002): Send Access-Request to 1.8.91.8:1645 id 1645/1, 
len 231

Router#

*Feb 22 08:33:08.007: RADIUS: Retransmit to (1.8.91.8:1645,1646) for id 1645/1

*Feb 22 08:33:08.011: RADIUS: Received from id 1645/1 1.8.91.8:1645, Access-Challenge, len 
75

*Feb 22 08:33:08.011: RADIUS/DECODE: EAP-Message fragments, 29, total 29 bytes

*Feb 22 08:33:08.011: RADIUS/ENCODE(00000002):Orig. component type = DOT1X

*Feb 22 08:33:08.011: RADIUS/ENCODE: NAS PORT sending disabled

*Feb 22 08:33:08.011: RADIUS(00000002): Config NAS IP: 0.0.0.0

*Feb 22 08:33:08.011: RADIUS(00000002): Config NAS IP: 0.0.0.0

*Feb 22 08:33:08.011: RADIUS: Attribute 55 not sent, as system clock is not set

*Feb 22 08:33:08.011: RADIUS/ENCODE: Best Local IP-Address 1.8.84.1 for Radius-Server 
1.8.91.8

*Feb 22 08:33:08.011: RADIUS(00000002): Send Access-Request to 1.8.91.8:1645 id 1645/2, 
len 227

*Feb 22 08:33:08.019: RADIUS: Received from id 1645/2 1.8.91.8:1645, Access-Accept, len 99

*Feb 22 08:33:08.019: RADIUS/DECODE: EAP-Message fragments, 4, total 4 bytes

*Feb 22 08:33:08.031: RADIUS/E

Router#NCODE(00000003):Orig. component type = AGW

*Feb 22 08:33:08.031: RADIUS/ENCODE: NAS PORT sending disabled

*Feb 22 08:33:08.031: RADIUS(00000003): Config NAS IP: 0.0.0.0

*Feb 22 08:33:08.031: RADIUS/ENCODE: Best Local IP-Address 1.8.84.1 for Radius-Server 
1.8.91.8

*Feb 22 08:33:08.031: RADIUS(00000003): Send Accounting-Request to 1.8.91.8:1646 id 
1646/1, len 206

*Feb 22 08:33:08.115: RADIUS: Received from id 1646/1 1.8.91.8:1646, Accounting-response, 
len 20

Router#

*Feb 22 08:34:10.623: RADIUS/ENCODE(00000003):Orig. component type = AGW

*Feb 22 08:34:10.623: RADIUS/ENCODE: NAS PORT sending disabled

*Feb 22 08:34:10.623: RADIUS(00000003): Config NAS IP: 0.0.0.0

*Feb 22 08:34:10.623: RADIUS/ENCODE: Best Local IP-Address 1.8.84.1 for Radius-Server 
1.8.91.8

*Feb 22 08:34:10.623: RADIUS(00000003): Send Accounting-Request to 1.8.91.8:1646 id 
1646/2, len 236

*Feb 22 08:34:10.675: RADIUS: Received from id 1646/2 1.8.91.8:1646, Accounting-response, 
len 20

debug wimax agw aaa

To display AAA authentication or accounting related events or errors, use the debug wimax agw aaa command in privileged EXEC mode. Use the no version of the command to disable debugging.

debug wimax agw aaa {accounting | authentication} {events | errors}

no debug wimax agw aaa {accounting | authentication} {events | errors}

Syntax Description

accounting	Displays AAA accounting related events or errors.
authentication	Displays AAA authentication related events or errors.
events	Displays events related to AAA accounting or authentication.
errors	Displays errors related to AAA accounting or authentication.

Defaults

There are no default values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

Here is sample output for AAA authentication events:

Router#debug wim agw aaa authentication events 

WiMAX AGW AAA authentication events debugging is on

Router#

*Feb 23 07:53:49.397: AGW-Aaa: <1000003B0009>Allocated AAA unqiue id = 12

*Feb 23 07:53:49.397: AGW-Auth: <1000003B0009>Created AAA Auth context with UID 0xC

*Feb 23 07:53:49.397: AGW-Auth: <1000003B0009>Creating EAP LowerLayer context

*Feb 23 07:53:49.397: AGW-Auth: <1000003B0009>Created EAP lower layer handle with 
0x9000007

*Feb 23 07:53:49.397: AGW-Auth: <1000003B0009>Received EAP evt EAP_TX_PACKET(0)

*Feb 23 07:53:49.397: AGW-Auth: <1000003B0009>Received EAP evt 
EAP_GET_AAA_METHOD_LISTS(10)

*Feb 23 07:53:49.397: AGW-Auth: <1000003B0009>EAP evt EAP_GET_AAA_METHOD_LISTS(10) - 
usrgrp set

*Feb 23 07:53:49.397: AGW-Auth: <1000003B0009>Received EAP evt EAP_GET_PEER_MAC_ADDRESS(8)

*Feb 23 07:53:49.397: AGW-Auth: <1000003B0009>Received EAP evt 
EAP_CUSTOMIZE_AAA_REQUEST(7)

*Feb 23 07:53:49.405: AGW-Auth: <1000003B0009>Received EAP evt EAP_TX_PACKET(0)

*Feb 23 07:53:49.405: AGW-Auth: <1000003B0009>Received EAP evt EAP_TX_PACKET(0)

*Feb 23 07:53:49.409: AGW-Auth: <1000003B0009>Received EAP evt 
EAP_GET_AAA_METHOD_LISTS(10)

*Feb 23 07:53:49.413: AGW-Auth: <10

asn#00003B0009>EAP evt EAP_GET_AAA_METHOD_LISTS(10) - Ignoring [usrgrp already set]

*Feb 23 07:53:49.413: AGW-Auth: <1000003B0009>Received EAP evt 
EAP_CUSTOMIZE_AAA_REQUEST(7)

*Feb 23 07:53:49.417: AGW-Auth: <1000003B0009>Received EAP evt EAP_TX_PACKET(0)

*Feb 23 07:53:49.421: AGW-Auth: <1000003B0009>Received EAP evt 
EAP_GET_AAA_METHOD_LISTS(10)

*Feb 23 07:53:49.421: AGW-Auth: <1000003B0009>EAP evt EAP_GET_AAA_METHOD_LISTS(10) - 
Ignoring [usrgrp already set]

*Feb 23 07:53:49.421: AGW-Auth: <1000003B0009>Received EAP evt 
EAP_CUSTOMIZE_AAA_REQUEST(7)

*Feb 23 07:53:49.425: AGW-Auth: <1000003B0009>Received EAP evt EAP_TX_PACKET(0)

*Feb 23 07:53:49.425: AGW-Auth: <1000003B0009>Received EAP evt 
EAP_GET_AAA_METHOD_LISTS(10)

*Feb 23 07:53:49.425: AGW-Auth: <1000003B0009>EAP evt EAP_GET_AAA_METHOD_LISTS(10) - 
Ignoring [usrgrp already set]

*Feb 23 07:53:49.685: AGW-Auth: <1000003B0009>Received EAP evt 
EAP_CUSTOMIZE_AAA_REQUEST(7)

*Feb 23 07:53:49.689: AGW-Auth: <1000003B0009>Received EAP evt EAP_KEY_AVAILABLE(3)

*Feb 23 07:53:49.689: AGW-Auth: <1000003B0009>Received EAP evt EAP_SUCCESS(1)

*Feb 23 07:53:49.689: AGW-Auth: <1000003B0009>Received Class attr (class-wimax-changed)

*Feb 23 07:53:49.689: AGW-Auth: <1000003B0009>Recevied Absolute(session) timeout 1500 secs

*Feb 23 07:53:49.689: AGW-Auth: <1000003B0009>Recevied Idle timeout 600 secs

*Feb 23 07:53:49.689: AGW-Auth: <1000003B0009>Received termination action 1

*Feb 23 07:53:49.689: AGW-Auth: <1000003B0009>Received MS-MPPE-Send-Key, length 50, key 
length 32

*Feb 23 07:53:49.689: AGW-Auth: <1000003B0009>Received MS-MPPE-Recv-Key, length 50, key 
length 32

*Feb 23 07:53:49.689: AGW-Auth: <1000003B0009>Received AAA Session ID

*Feb 23 07:53:49.689: AGW-Auth: <1000003B0009>Deleting EAP LowerLayer context with handle 
0x9000007

*Feb 23 07:53:49.701: AGW-Aaa: <1000003B0009><F[5]>Allocated AAA unqiue id = 13

Here is an example of an accounting message on MS open:

Router#debug wimax agw aaa accounting events

WiMAX AGW AAA accounting events debugging is on router#

*Feb 23 08:09:37.521: AGW-Acct: <1000000B0002><F[4]>Invoked 

get dynamic attributes for path Unknown

router#

*Feb 23 08:09:43.181: AGW-Aaa: <100000310009><F[6]>Allocated 

AAA unqiue id = 15

*Feb 23 08:09:43.181: AGW-Acct: <100000310009><F[6]>Invoked 

get dynamic attributes for path Start

*Feb 23 08:09:43.181: AGW-Acct: <100000310009><F[6]>Started 

accounting for uid 15 with uname swimeap@wimax.org

router# 

---

Note The ms open command is run on the simulator, and the debug messages are observed on the ASNGW.

---

Here is an example of an accounting message on MS close:

Router#debug wimax agw aaa accounting events

WiMAX AGW AAA accounting events debugging is on router#

asn#

*Feb 23 08:11:54.829: AGW-Acct: <100000310009><F[6]>Invoked 

get dynamic attributes for path Stop

*Feb 23 08:11:54.829: AGW-Acct: <100000310009><F[6]>Stopped 

accounting for uid 15 with uname swimeap@wimax.org

---

Note The ms open command is run on the simulator, and the debug messages are observed on the ASNGW.

---

debug wimax agw message

To enable conditional debugging for various types of ASN GW messages, use the debug wimax agw message command in privileged EXEC mode.

debug wimax agw message [events | errors | dump]

Syntax Description

events	Displays brief information on the processing of all transmitted and received messages.
errors	Displays details of any errors encountered during message processing.
dump	Displays details of all transmitted and received messages. Output will include the following: •IP packet details. Source/destination addresses, version, IP header length, TOS, total length, flags, IP fragmentation details, TTL, protocol, checksum. •UDP information. Source/destination ports, checksum, length. •Function-Type and Messaage-Type of the message. •Dump of all the TLVs contained in the message.

Defaults

There are no default values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Examples

The following example displays a successful message open:

Router#debug wimax agw message dump

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Rx (GigabitEthernet0/1)

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> IP: Src: 10.1.1.70, Dst: 2.2.2.2

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Version: 0x4, IHL: 0x5, TOS: 0xC0

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Total Length: 0x4A, ID: 0x1A

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Flags: Reserved: 0x0, DontFrag: 0x0, 
MoreFrag: 0x0

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Fragment offset: 0x0, TTL: 0xFE, Protocol: 
0x11

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Checksum: 0xAC7E

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> UDP: Src Port: 0x8B7, Dst Port: 0x8B7

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Checksum: 0x7E1B, Length: 0x36

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Message: Type 0x090F (0x09, 0x0F)

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> FT: MS State Change, MT: Pre Attachment 
Request

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Version: 0x01, Flags: 0x00, Type 0x90F

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> MSID: 067622242222, Reserved_1: 0x0000, Len: 
0x2E

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> TransactionID: 0x0001, Reserved_2: 0x0000, 

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Rx (GigabitEthernet0/1)

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> IP: Src: 10.1.1.70, Dst: 2.2.2.2

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Version: 0x4, IHL: 0x5, TOS: 0xC0

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Total Length: 0x30, ID: 0x1B

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Flags: Reserved: 0x0, DontFrag: 0x0, 
MoreFrag: 0x0

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Fragment offset: 0x0, TTL: 0xFE, Protocol: 
0x11

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Checksum: 0xAC97

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> UDP: Src Port: 0x8B7, Dst Port: 0x8B7

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Checksum: 0x8A1B, Length: 0x1C

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> Message: Type 0x0911 (0x09, 0x11)

*Feb 23 08:29:28.344: AGW-Msg: <067622242222> FT: MS State Change, MT: Pre Attachment ACK 

Here is sample Message Events output on a successful MS Close:

Router#debug wimax agw message events

*Feb 23 08:33:49.064: AGW-Msg: <100022230001>Rx SrcAddr: 10.1.1.70, SrcPort: 2231, TID: 
0x3, Type: 0x304, Len: 0x38, Flag: 0x2, FT: Data Path(0x3), MT: Deregistration 
Request(0x4)

*Feb 23 08:33:49.064: AGW-Msg: <100022230001>[Decode] FT/MT: 3/4, Ref pt: 3, TID rcvd 
0X3(3), peer 0X2(2)[9/8], our 0X8002(32770)[3/12], Previous peer 0x1(1)[9/15], Previous 
our 0X8001(32769)[3/12],TID RC: 1

*Feb 23 08:33:49.064: AGW-Msg: <100022230001>[Decode] Req FT/MT: 3/4, Ref pt: 3, TID RC: 
1, RC: Success(0)

*Feb 23 08:33:49.064: AGW-Msg: <100022230001>Tx DstAddr: 10.1.1.70, SrcPort: 2231, TID: 
0x3, Type: 0x305, Len: 0x38, Flag: 0x0, FT: Data Path(0x3), MT: Deregistration 
Response(0x5)

*Feb 23 08:33:49.064: AGW-Msg: <100022230001>[Decode] FT/MT: 3/4, Ref pt: 3, Retcode = 
Success(0)

*Feb 23 08:33:49.064: AGW-Msg: <100022230001>Rx SrcAddr: 10.1.1.70, SrcPort: 2231, TID: 
0x3, Type: 0x306, Len: 0x1C, Flag: 0x0, FT: Data Path(0x3), MT: Deregistration Ack(0x6)

*Feb 23 08:33:49.064: AGW-Msg: <100022230001>[Decode] FT/MT: 3/6, Ref pt: 3, TID rcvd 
0X3(3), peer 0X3(3)[3/4], our 0X8002(32770)[3/12], Previous peer 0x2(2)[9/8], Previous our 
0X8001(32769)[3/12],TID RC: 1

*Feb 23 08:33:49.064: AGW-Msg: <100022230001>[Decode] Req FT/MT: 3/6, Ref pt: 3, TID RC: 
1, RC: Success(0)

*Feb 23 08:33:49.064: AGW-Msg: <100022230001>Deleting the R6 TID 0X65A3B46C, 
10.1.1.70/2.2.2.2/0

*Feb 23 08:33:49.064: AGW-Msg: <100022230001>[Decode] FT/MT: 3/6, Ref pt: 3, Retcode = 
Success(0)

Here is sample Message Events output when MS open fails:

Router#debug wimax agw message events

*Feb 23 11:00:40.408: AGW-Msg: <067611141111>Rx SrcAddr: 10.1.1.70, SrcPort: 2231, TID: 
0x1, Type: 0x90F, Len: 0x2E, Flag: 0x0, FT: MS State Change(0x9), MT: Pre Attachment 
Request(0xF)

*Feb 23 11:00:40.408: AGW-Msg: <067611141111>[Decode] Req FT/MT: 9/15, Ref pt: 3, TID RC: 
6, RC: Success(0)

*Feb 23 11:00:40.408: AGW-Msg: <067611141111>[Decode] Created the R6 TID 0X65A3B4A8, 
10.1.1.70/2.2.2.2/9

*Feb 23 11:00:40.408: AGW-Msg: <067611141111>Tx DstAddr: 10.1.1.70, SrcPort: 2231, TID: 
0x1, Type: 0x910, Len: 0x36, Flag: 0x0, FT: MS State Change(0x9), MT: Pre Attachment 
Response(0x10)

*Feb 23 11:00:40.408: AGW-Msg: <067611141111>[Decode] FT/MT: 9/15, Ref pt: 3, Retcode = 
Success(0)

*Feb 23 11:00:40.408: AGW-Msg: <067611141111>Rx SrcAddr: 10.1.1.70, SrcPort: 2231, TID: 
0x1, Type: 0x911, Len: 0x14, Flag: 0x0, FT: MS State Change(0x9), MT: Pre Attachment 
ACK(0x11)

*Feb 23 11:00:40.408: AGW-Msg: <067611141111>[Decode] FT/MT: 9/17, Ref pt: 3, TID rcvd 
0X1(1), peer 0X1(1)[9/15], our 0X8000(32768)[0/0], Previous peer 0x0(0)[0/0], Previous our 
0X0(0)[0/0],TID RC: 1

*Feb 23 11:00:40.408: AGW-Msg: <067611141111>[Decode] Req FT/MT: 9/17, Ref pt: 3, TID RC: 
1, RC: Success(0)

*Feb 23 11:00:40.408: AGW-Msg: <067611141111>[Decode] FT/MT: 9/17, Ref pt: 3, Retcode = 
Success(0)

*Feb 23 11:00:40.408: AGW-Msg: <067611141111>FT/MT: 8/2, generated TID 0X8001(32769), 
10.1.1.70/2.2.2.2/8

*Feb 23 11:00:40.408: AGW-Msg: <067611141111>Tx DstAddr: 10.1.1.70, SrcPort: 2231, TID: 
0x8001, Type: 0x802, Len: 0x1D, Flag: 0x0, FT: Auth Relay(0x8), MT: EAP Transfer(0x2)

*Feb 23 11:00:40.412: AGW-Msg: <067611141111>Rx SrcAddr: 10.1.1.70, SrcPort: 2231, TID: 
0x2, Type: 0x802, Len: 0x31, Flag: 0x0, FT: Auth Relay(0x8), MT: EAP Transfer(0x2)

*Feb 23 11:00:40.468: AGW-Msg: <067611141111>Tx DstAddr: 10.1.1.70, SrcPort: 2231, TID: 
0x8006, Type: 0x304, Len: 0x38, Flag: 0x2, FT: Data Path(0x3), MT: Deregistration 
Request(0x4)

*Feb 23 11:00:40.468: AGW-Msg: <067611141111>Rx SrcAddr: 10.1.1.70, SrcPort: 2231, TID: 
0x8006, Type: 0x305, Len: 0x38, Flag: 0x0, FT: Data Path(0x3), MT: Deregistration 
Response(0x5)

*Feb 23 11:00:40.468: AGW-Msg: <067611141111>[Decode] FT/MT: 3/5, Ref pt: 3, TID rcvd 
0X8006(32774), peer 0X6(6)[8/2], our 0X8006(32774)[3/4], Previous peer 0x5(5)[8/2], 
Previous our 0X8005(32773)[8/2],TID RC: 1

*Feb 23 11:00:40.468: AGW-Msg: <067611141111>[Decode] Req FT/MT: 3/5, Ref pt: 3, TID RC: 
1, RC: Success(0)

*Feb 23 11:00:40.468: AGW-Msg: <067611141111>Tx DstAddr: 10.1.1.70, SrcPort: 2231, TID: 
0x8006, Type: 0x306, Len: 0x1C, Flag: 0x0, FT: Data Path(0x3), MT: Deregistration Ack(0x6)

*Feb 23 11:00:40.468: AGW-Msg: <067611141111>Deleting the R6 TID 0X65A3B4A8, 
10.1.1.70/2.2.2.2/0

*Feb 23 11:00:40.468: AGW-Msg: <067611141111>[Decode] FT/MT: 3/5, Ref pt: 3, Retcode = 
Success(0)

Here is sample Message Events output when handoff fails:

Router#debug wimax agw message events

*Feb 23 12:35:52.003: AGW-Msg: <100022230001>Rx SrcAddr: 10.1.1.72, SrcPort: 2231, TID: 
0x1, Type: 0x401, Len: 0x2C, Flag: 0x0, FT: Context Delivery(0x4), MT: Context Delivery 
Request(0x1)

*Feb 23 12:35:52.003: AGW-Msg: <100022230001>[Decode] Req FT/MT: 4/1, Ref pt: 3, TID RC: 
5, RC: Success(0)

*Feb 23 12:35:52.003: AGW-Msg: <100022230001>[Decode] Created the R6 TID 0X65A3B3F4, 
10.1.1.72/2.2.2.2/4

*Feb 23 12:35:52.003: AGW-Msg: <100022230001>Tx DstAddr: 10.1.1.72, SrcPort: 2231, TID: 
0x1, Type: 0x402, Len: 0x69, Flag: 0x0, FT: Context Delivery(0x4), MT: Context Delivery 
Report(0x2)

*Feb 23 12:35:52.003: AGW-Msg: <100022230001>[Decode] FT/MT: 4/1, Ref pt: 3, Retcode = 
Success(0)

*Feb 23 12:35:52.007: AGW-Msg: <100022230001>Rx SrcAddr: 10.1.1.72, SrcPort: 2231, TID: 
0x2, Type: 0x30C, Len: 0x1D2, Flag: 0x0, FT: Data Path(0x3), MT: Registration Request(0xC)

*Feb 23 12:35:52.007: AGW-Msg: <100022230001>[Decode] FT/MT: 3/12, Ref pt: 3, TID rcvd 
0X2(2), peer 0X1(1)[4/1], our 0X8000(32768)[0/0], Previous peer 0x0(0)[0/0], Previous our 
0X0(0)[0/0],TID RC: 1

*Feb 23 12:35:52.007: AGW-Msg: <100022230001>[Decode] Req FT/MT: 3/12, Ref pt: 3, TID RC: 
1, RC: Success(0)

*Feb 23 12:35:52.007: AGW-Msg: <100022230001><F[41]>Tx DstAddr: 10.1.1.72, SrcPort: 2231, 
TID: 0x2, Type: 0x30D, Len: 0xC0, Flag: 0x0, FT: Data Path(0x3), MT: Registration 
Response(0xD)

*Feb 23 12:35:52.007: AGW-Msg: <100022230001><F[42]>[Decode] FT/MT: 3/12, Ref pt: 3, 
Retcode = Success(0)

*Feb 23 12:35:52.007: AGW-Msg: <100022230001>Rx SrcAddr: 10.1.1.72, SrcPort: 2231, TID: 
0x2, Type: 0x30E, Len: 0x1C, Flag: 0x0, FT: Data Path(0x3), MT: Registration Ack(0xE)

*Feb 23 12:35:52.007: AGW-Msg: <100022230001>[Decode] FT/MT: 3/14, Ref pt: 3, TID rcvd 
0X2(2), peer 0X2(2)[3/12], our 0X8000(32768)[0/0], Previous peer 0x2(2)[3/12], Previous 
our 0X0(0)[0/0],TID RC: 1

*Feb 23 12:35:52.007: AGW-Msg: <100022230001>[Decode] Req FT/MT: 3/14, Ref pt: 3, TID RC: 
1, RC: Success(0)

*Feb 23 12:35:52.007: AGW-Msg: <100022230001>FT/MT: 3/4, generated TID 0X8003(32771), 
10.1.1.70/2.2.2.2/3

*Feb 23 12:35:52.007: AGW-Msg: <100022230001><F[41]>Tx DstAddr: 10.1.1.70, SrcPort: 2231, 
TID: 0x8003, Type: 0x304, Len: 0x38, Flag: 0x0, FT: Data Path(0x3), MT: Deregistration 
Request(0x4)

*Feb 23 12:35:52.007: AGW-Msg: <100022230001><F[42]>[Decode] FT/MT: 3/14, Ref pt: 3, 
Retcode = Success(0)

*Feb 23 12:35:52.007: AGW-Msg: <100022230001>Rx SrcAddr: 10.1.1.72, SrcPort: 2231, TID: 
0x3, Type: 0x402, Len: 0x69, Flag: 0x0, FT: Context Delivery(0x4), MT: Context Delivery 
Report(0x2)

*Feb 23 12:35:52.007: AGW-Msg: <100022230001>[Decode] FT/MT: 4/2, Ref pt: 3,

"Retcode = Fail - Abort(1)"

debug wimax agw message tlv

To display various ASN GW TLV messages, use the debug wimax agw message tlv command in privileged EXEC mode.

debug wimax agw message tlv [events | errors | dump]

Syntax Description

events	Displays brief information on the encoding and decoding of all TLVs.
errors	Displays details of any errors encountered during TLV encoding and decoding.
dump	Displays details of all TLVs encoded and decoded. The TLV type, length, and a hex dump of the TLV value are printed.

Defaults

There are no default values.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example displays TLV events on a successful MS Open:

Router#debug wimax agw message tlv events

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: MS Information(0x0001), Length: 
0x0006

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: Authorization Policy(0x0028), Length: 
0x0002

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: Base Station Information(0x0002), 
Length: 0x000C

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: Base Station ID(0x0014), Length: 
0x0008

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: MS Information(0x0001), Length: 
0x0026

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: Key Change Indicator(0x005F), Length: 
0x0001

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: Registration Context(0x0058), Length: 
0x001D

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: MTG Profile(0x0069), Length: 0x0001

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: CS Type(0x0068), Length: 0x0002

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: Number of Downlink CIDs(0x006A), 
Length: 0x0002

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: Number of Uplink CIDs(0x006B), 
Length: 0x0002

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: Number of Uplink Classifiers(0x006C), 
Length: 0x0002

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: Base Station Information(0x0002), 
Length: 0x000C

*Feb 23 08:37:59.864: AGW-Tlv: <100022230001>  Type: Base Station ID(0x0014), Length: 
0x0008

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: Registration Type(0x002E), Length: 
0x0004

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: MS Information(0x0001), Length: 
0x004C

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: Anchor Gateway ID(0x001B), Length: 
0x0004

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: SF Information(0x0003), Length: 
0x0014

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: Direction(0x005E), Length: 0x0002

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: Service Flow Identifier(0x003B), 
Length: 0x0004

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: Reservation Result(0x0065), Length: 
0x0002

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: SF Information(0x0003), Length: 
0x0028

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: Direction(0x005E), Length: 0x0002

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: Service Flow Identifier(0x003B), 
Length: 0x0004

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: Reservation Result(0x0065), Length: 
0x0002

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: DP Information(0x0008), Length: 
0x0010

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: DP Identifier(GRE Key)(0x0023), 
Length: 0x0004

*Feb 23 08:37:59.868: AGW-Tlv: <100022230001>  Type: Data Path End point 
Identifier(0x0024), Length: 0x0004

The following example displays TLV events on a successful MS close:

Router#debug wimax agw message tlv dump

*Feb 23 08:39:54.424: AGW-Tlv: <100022230001>  Type: Registration Type(0x002E), Length: 
0x0004

*Feb 23 08:39:54.424: AGW-Tlv: <100022230001>   Value: 4

*Feb 23 08:39:54.424: AGW-Tlv: <100022230001>  Type: Anchor Gateway ID(0x001B), Length: 
0x0004

*Feb 23 08:39:54.424: AGW-Tlv: <100022230001>    Hex: < 02 02 02 02 >

*Feb 23 08:39:54.424: AGW-Tlv: <100022230001>  Type: Base Station ID(0x0014), Length: 
0x0008

*Feb 23 08:39:54.424: AGW-Tlv: <100022230001>    Hex: < 0A 01 01 46 00 00 00 00 >

*Feb 23 08:39:54.428: AGW-Tlv: <100022230001>  Type: Registration Type(0x002E), Length: 
0x0004

*Feb 23 08:39:54.428: AGW-Tlv: <100022230001>   Value: 4

debug wimax agw path

To display BS path related messages, use the debug wimax agw path command in privileged EXEC mode.

debug wimax agw path [events | errors]

Syntax Description

events	Displays information on BS path related events.
errors	Displays information on BS path related errors

Defaults

There are no default values.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

Here is sample Path Events output on a successful MS Open:

Router#debug wimax agw path events

*Feb 23 10:32:36.496: AGW-Path: <(SU)-10.1.1.70>State transition Purging -> Ready

*Feb 23 10:32:36.496: AGW-Path: <(SU)-10.1.1.70>Stopping purge timer

*Feb 23 10:32:36.496: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 54 (refcount 1) with 
resend required 1

*Feb 23 10:32:36.496: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 29 (refcount 1) with 
resend required 0

*Feb 23 10:32:36.504: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 53 (refcount 1) with 
resend required 0

*Feb 23 10:32:36.512: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 42 (refcount 1) with 
resend required 1

*Feb 23 10:32:36.512: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 81 (refcount 1) with 
resend required 1

*Feb 23 10:32:36.512: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 252 (refcount 1) 
with resend required 1

*Feb 23 10:32:36.516: AGW-Path: <(DG)-10.1.1.70>Stopping purge timer

*Feb 23 10:32:36.516: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 28 (refcount 1) with 
resend required 0

*Feb 23 10:32:36.520: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 274 (refcount 1) 
with resend required 1

*Feb 23 10:32:36.520: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 28 (refcount 1) with 
resend required 0

Here is sample Path Events output when an MS open fails:

Router#debug wimax agw path events

*Feb 23 10:35:05.196: AGW-Path: <(SU)-10.1.1.70>State transition Idle -> Ready

*Feb 23 10:35:05.196: AGW-Path: <(SU)-10.1.1.70>Created path with handle 0x6B000016

*Feb 23 10:35:05.196: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 54 (refcount 1) with 
resend required 1

*Feb 23 10:35:05.200: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 29 (refcount 1) with 
resend required 0

*Feb 23 10:35:05.204: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 30 (refcount 1) with 
resend required 0

*Feb 23 10:35:05.216: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 1048 (refcount 1) 
with resend required 0

*Feb 23 10:35:05.220: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 1048 (refcount 1) 
with resend required 0

*Feb 23 10:35:05.228: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 922 (refcount 1) 
with resend required 0

*Feb 23 10:35:05.256: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 56 (refcount 1) with 
resend required 1

*Feb 23 10:35:05.256: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 28 (refcount 1) with 
resend required 0

*Feb 23 10:35:05.256: AGW-Path: <(SU)-10.1.1.70>State transition Ready -> Purging

*Feb 23 10:35:05.256: AGW-Path: <(SU)-10.1.1.70>Starting purge timer for 20000 msecs

*Feb 23 10:35:25.428: AGW-Path: <(SU)-10.1.1.70>Expired purge timer after 20000 msecs

*Feb 23 10:35:25.428: AGW-Path: <(SU)-10.1.1.70>Deleting the path with handle 0x6B000016

Here is sample Path Events output on a successful MS Close:

Router#debug wimax agw path events

*Feb 23 10:34:12.204: AGW-Path: <(SU)-10.1.1.70>Enqueuing pak of size 56 (refcount 1) with 
resend required 1

*Feb 23 10:34:12.208: AGW-Path: <(DG)-10.1.1.70>Starting purge timer for 20000 msecs

*Feb 23 10:34:12.208: AGW-Path: <(SU)-10.1.1.70>State transition Ready -> Purging

*Feb 23 10:34:12.208: AGW-Path: <(SU)-10.1.1.70>Starting purge timer for 20000 msecs

*Feb 23 10:34:32.392: AGW-Path: <(DG)-10.1.1.70>Expired purge timer after 20000 msecs

*Feb 23 10:34:32.392: AGW-Path: <(DG)-10.1.1.70>Deleting the path with handle 0x35000015

*Feb 23 10:34:32.392: AGW-Path: <(SU)-10.1.1.70>Expired purge timer after 20000 msecs

*Feb 23 10:34:32.392: AGW-Path: <(SU)-10.1.1.70>Deleting the path with handle 0x63000013

debug wimax agw r6 flow

To display ASN GW flow information, use the debug wimax agw r6 flow command in Privileged EXEC mode.

debug wimax agw r6 flow [events | errors | fsm events | fsm errors]

Syntax Description

events	Displays information on flow creation and deletion.
errors	Displays details of any flow related errors.
fsm events	Displays information regarding the flow FSM. Output shows all state transitions, and indicates if each transition was successfully completed.
fsm errors	Display details of errors encountered in the execution of the subscriber FSM.

Defaults

There are no default values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

Here is sample R6 flow output for a successful MS Open:

Router#debug wimax agw r6 flow events

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[21]>[Downlink] Predefined SF QoS info set

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[21]>[Downlink] Predefined SF IPv4 TFT set

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[21]>[Uplink] Predefined SF QoS info set

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[21]>[Uplink] Predefined SF IPv4 TFT set

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[21]>Created flow with handle 0xD0000015, 
local Id 0x15 for session handle 0xE500000F

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[21]>[ISF] Created flow with index 0

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[22]>[Downlink] Predefined SF QoS info set

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[22]>[Downlink] Predefined SF IPv4 TFT set

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[22]>[Uplink] Predefined SF QoS info set

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[22]>[Uplink] Predefined SF IPv4 TFT set

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[22]>Created flow with handle 0x62000016, 
local Id 0x16 for session handle 0xE500000F

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[22]>[SF] Created flow with index 1

*Feb 23 10:18:00.992: AGW-Flow: <100022230001><F[21]>Creating the sigpak resend details 
0x207497F0, max resend 10, timeout 10000 msecs, timer type 2(16)

*Feb 23 10:18:00.996: AGW-Flow: <100022230001><F[21]>Starting pak resend timer 0x207497F0 
for 10000 msecs with max resend 10, current resend 0, timer type 2(16)

*Feb 23 10:18:00.996: AGW-Flow: <100022230001><F[21]>Deleting the sigpak resend details 
0x207497F0

*Feb 23 10:18:00.996: AGW-Flow: <100022230001><F[21]>Stopping pak resend timer 0x207497F0 
for 10000 msecs with max resend 10, current resend 0, timer type 2(16)

*Feb 23 10:18:00.996: AGW-Flow: <100022230001><F[21]><(DG)-10.1.1.70>Link the flow to the 
path

Here is sample R6 flow output for a successful MS Close:

Router#debug wimax agw r6 flow events

*Feb 23 10:17:08.868: AGW-Flow: <100022230001><F[17]>Deleting flow with handle 0x87000011 
for session handle 0x7900000D

*Feb 23 10:17:08.868: AGW-Flow: <100022230001><F[17]><(DG)-10.1.1.70>Delink the flow from 
the path

*Feb 23 10:17:08.868: AGW-Flow: <100022230001><F[17]>Deallocating the Downlink SF details

*Feb 23 10:17:08.868: AGW-Flow: <100022230001><F[17]>Deallocating the Uplink SF details

*Feb 23 10:17:08.868: AGW-Flow: <100022230001><F[17]>Deleting flow

*Feb 23 10:17:08.868: AGW-Flow: <100022230001><F[18]>Deleting flow with handle 0x3F000012 
for session handle 0x7900000D

*Feb 23 10:17:08.868: AGW-Flow: <100022230001><F[18]><(DG)-10.1.1.70>Delink the flow from 
the path

*Feb 23 10:17:08.868: AGW-Flow: <100022230001><F[18]>Deallocating the Downlink SF details

*Feb 23 10:17:08.868: AGW-Flow: <100022230001><F[18]>Deallocating the Uplink SF details

*Feb 23 10:17:08.868: AGW-Flow: <100022230001><F[18]>Deleting flow

Here is sample R6 Flow FSM Events output for a successful MS Open:

Router#debug wimax agw r6 flow fsm events

*Feb 23 10:25:44.324: AGW-FlowFSM:<067622272222><F[27]>SF Idle(0) -> SF Establishing(1) on 
event Tx Reg Req(4) with retcode Ok(0)

*Feb 23 10:25:44.328: AGW-FlowFSM:<067622272222><F[27]>SF Establishing(1) -> SF 
Establishing(1) on event Rx Reg Rsp(5) with retcode Ok(0)

*Feb 23 10:25:44.328: AGW-FlowFSM:<067622272222><F[27]>SF Establishing(1) -> ISF Wait For 
Addr Alloc(2) on event Tx Reg Ack(6) with retcode ISF - Ok(5)

*Feb 23 10:25:44.328: AGW-FlowFSM:<067622272222><F[27]>ISF Wait For Addr Alloc(2) -> SF 
Ready(4) on event SF Addr Assigned(7) with retcode Ok(0)

*Feb 23 10:25:44.328: AGW-FlowFSM:<067622272222><F[27]>SF Ready(4) -> SF Ready(4) on event 
Up(1) with retcode Ok(0)

*Feb 23 10:25:44.332: AGW-FlowFSM:<067622272222><F[28]>SF Idle(0) -> SF Establishing(1) on 
event Tx Reg Req(4) with retcode Ok(0)

*Feb 23 10:25:44.332: AGW-FlowFSM:<067622272222><F[28]>SF Establishing(1) -> SF 
Establishing(1) on event Rx Reg Rsp(5) with retcode Ok(0)

*Feb 23 10:25:44.332: AGW-FlowFSM:<067622272222><F[28]>SF Establishing(1) -> SF Ready(4) 
on event Tx Reg Ack(6) with retcode Ok(0)

*Feb 23 10:25:44.332: AGW-FlowFSM:<067622272222><F[28]>SF Ready(4) -> SF Ready(4) on event 
Up(1) with retcode Ok(0)

Here is sample R6 Flow FSM Events output for a successful MS Close:

Router#debug wimax agw r6 flow fsm events

*Feb 23 10:24:06.592: AGW-FlowFSM:<067622262222><F[19]>SF Ready(4) -> SF Cleanup(7) on 
event Session Closed(2) with retcode Ok(0)

*Feb 23 10:24:06.592: AGW-FlowFSM:<067622262222><F[19]>SF Cleanup(7) -> SF Cleanup(7) on 
event Session Closed(2) with retcode Ok(0)

*Feb 23 10:24:06.592: AGW-FlowFSM:<067622262222><F[20]>SF Ready(4) -> SF Cleanup(7) on 
event Session Closed(2) with retcode Ok(0)

*Feb 23 10:24:06.592: AGW-FlowFSM:<067622262222><F[20]>SF Cleanup(7) -> SF Cleanup(7) on 
event Session Closed(2) with retcode Ok(0)

debug wimax agw r6 session

To display ASN GW R6 session information, use the debug wimax agw r6 session command in Privileged EXEC mode.

debug wimax agw r6 session [events | errors | fsm events | fsm errors]

Syntax Description

events	Displays information on session creation and deletion.
errors	Display details of any R6 session related errors.
fsm events	Display information regarding the session FSM. Output will show all state transitions and indicates if each transition was successfully completed.
fsm errors	Display details of any errors encountered in the execution of the session FSM.

Defaults

Ther e are no default values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Examples

Here is sample output for R6 session events on a successful MS Open:

Router#debug wimax agw r6 session events

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Created session with handle 0x61000022, Id 
0x22 for subscriber handle 0x83000022

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001><(SU)-10.1.1.70>:Link the session to the 
path

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Created session

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Found usrgrp **unauthenticated** based on 
domain  for user 

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Creating the sigpak resend details 
0x654986B8, max resend 10, timeout 10000 msecs, timer type 1(2)

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Starting pak resend timer 0x654986B8 for 
10000 msecs with max resend 10, current resend 0, timer type 1(2)

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Deleting the sigpak resend details 
0x654986B8

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Stopping pak resend timer 0x654986B8 for 
10000 msecs with max resend 10, current resend 0, timer type 1(2)

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Starting protect timer Rx attach req for 110 
secs

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Creating the sigpak resend details 
0x2034967C, max resend 10, timeout 10000 msecs, timer type 1(8)

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Starting pak resend timer 0x2034967C for 
10000 msecs with max resend 10, current resend 0, timer type 1(8)

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Stopping protect timer Rx attach req

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Deleting the sigpak resend details 
0x2034967C

*Feb 23 12:55:34.715: AGW-Sess: <1000222A0001>Stopping pak resend timer 0x2034967C for 
10000 msecs with max resend 10, current resend 0, timer type 1(8)

*Feb 23 12:55:34.723: AGW-Sess: <1000222A0001><F[45]>Adding Host address 2.2.0.16

*Feb 23 12:55:34.723: AGW-Sess: <1000222A0001><F[45]>Static route IPv4 addr 2.2.0.16, aggr 
mask 255.255.255.255

*Feb 23 12:55:34.723: AGW-Sess: <1000222A0001><F[45]>Created new host for the session

*Feb 23 12:55:34.723: AGW-Sess: <1000222A0001><F[45]>Set host IPv4 address 2.2.0.16 for 
the session

*Feb 23 12:55:34.723: AGW-Sess: <1000222A0001>Starting Lease timer for host 2.2.0.16 with 
timeout 3540 seconds

*Feb 23 12:55:34.723: AGW-Sess: <1000222A0001>Inserting static route 2.2.0.16 
255.255.255.255 via 0.0.0.0, idb Virtual-Access2, tableid 0

*Feb 23 12:55:34.723: AGW-Sess: <1000222A0001>Added static route/inserted address 2.2.0.16 
255.255.255.255/0

*Feb 23 12:55:34.723: AGW-Sess: <1000222A0001>Ready to switch traffic for session

Here is sample output for R6 session events when MS open fails:

Router#debug wimax agw r6 session events

*Feb 23 08:51:02.728: AGW-Sess: <067611141111>Created session with handle 0x74000009, Id 
0x9 for subscriber handle 0xA3000009

*Feb 23 08:51:02.728: AGW-Sess: <067611141111><(SU)-10.1.1.70>:Link the session to the 
path

*Feb 23 08:51:02.728: AGW-Sess: <067611141111>Created session

*Feb 23 08:51:02.728: AGW-Sess: <067611141111>Creating the sigpak resend details 
0x65AEF5B4, max resend 10, timeout 10000 msecs, timer type 1(2)

*Feb 23 08:51:02.728: AGW-Sess: <067611141111>Starting pak resend timer 0x65AEF5B4 for 
10000 msecs with max resend 10, current resend 0, timer type 1(2)

*Feb 23 08:51:02.732: AGW-Sess: <067611141111>Deleting the sigpak resend details 
0x65AEF5B4

*Feb 23 08:51:02.732: AGW-Sess: <067611141111>Stopping pak resend timer 0x65AEF5B4 for 
10000 msecs with max resend 10, current resend 0, timer type 1(2)

*Feb 23 08:51:02.732: AGW-Sess: <067611141111>Username pushetty@eap-tls.com, domain is 
eap-tls.com, user is pushetty, delimiter @

*Feb 23 08:51:02.732: AGW-Sess: <067611141111>Found usrgrp eap-tls.com based on domain 
eap-tls.com for user pushetty@eap-tls.com

*Feb 23 08:51:02.788: AGW-Sess: <067611141111>[Authenticating / Auth Result Obtained] 

*Feb 23 08:51:02.788: AGW-Sess: <067611141111>Creating the sigpak resend details 
0x654986B8, max resend 10, timeout 10000 msecs, timer type 1(10)

*Feb 23 08:51:02.788: AGW-Sess: <067611141111>Starting pak resend timer 0x654986B8 for 
10000 msecs with max resend 10, current resend 0, timer type 1(10)

*Feb 23 08:51:02.788: AGW-Sess: <067611141111>Deleting the sigpak resend details 
0x654986B8

*Feb 23 08:51:02.788: AGW-Sess: <067611141111>Stopping pak resend timer 0x654986B8 for 
10000 msecs with max resend 10, current resend 0, timer type 1(10)

*Feb 23 08:51:02.788: AGW-Sess: <067611141111>Deleting session with handle 0x74000009 for 
subscriber handle 0xA3000009

*Feb 23 08:51:02.788: AGW-Sess: <067611141111><(SU)-10.1.1.70>Delink the session from the 
path

*Feb 23 08:51:02.788: AGW-Sess: <067611141111>Deleting session from usergroup

*Feb 23 08:51:02.788: AGW-Sess: <067611141111>Deleting session

Here is sample output for R6 session events when MS successfully closes:

Router#debug wimax agw r6 session events

*Feb 23 08:54:17.556: AGW-Sess: <067622242222>Creating the sigpak resend details 
0x65F35C00, max resend 10, timeout 10000 msecs, timer type 1(11)

*Feb 23 08:54:17.556: AGW-Sess: <067622242222>Starting pak resend timer 0x65F35C00 for 
10000 msecs with max resend 10, current resend 0, timer type 1(11)

*Feb 23 08:54:17.556: AGW-Sess: <067622242222>Deleting session with handle 0x49000008 for 
subscriber handle 0x6000008

*Feb 23 08:54:17.556: AGW-Sess: <067622242222>Deleting the sigpak resend details 
0x65F35C00

*Feb 23 08:54:17.556: AGW-Sess: <067622242222>Stopping pak resend timer 0x65F35C00 for 
10000 msecs with max resend 10, current resend 0, timer type 1(11)

*Feb 23 08:54:17.556: AGW-Sess: <067622242222><(SU)-10.1.1.70>Delink the session from the 
path

*Feb 23 08:54:17.556: AGW-Sess: <067622242222>Deleting session from usergroup

*Feb 23 08:54:17.556: AGW-Sess: <067622242222>Stopping session timer

*Feb 23 08:54:17.556: AGW-Sess: <067622242222>Deleting session

Here is sample output for R6 FSM Session Events on a successful MS Open:

Router#debug wimax agw r6 session fsm events

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Created session with handle 0x9C00000A, Id 
0xA for subscriber handle 0x200000A

*Feb 23 08:56:35.700: AGW-Sess: <100022230001><(SU)-10.1.1.70>:Link the session to the 
path

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Created session

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Found usrgrp **unauthenticated** based on 
domain  for user 

*Feb 23 08:56:35.700: AGW-SessFSM:<100022230001>Idle(0) -> Authorizing(1) on event Rx Pre 
Attach Req(1) with retcode Ok(0)

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Creating the sigpak resend details 
0x65F35C00, max resend 10, timeout 10000 msecs, timer type 1(2)

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Starting pak resend timer 0x65F35C00 for 
10000 msecs with max resend 10, current resend 0, timer type 1(2)

*Feb 23 08:56:35.700: AGW-SessFSM:<100022230001>Authorizing(1) -> Authorizing(1) on event 
Tx Pre Attach Rsp(2) with retcode Ok(0)

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Deleting the sigpak resend details 
0x65F35C00

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Stopping pak resend timer 0x65F35C00 for 
10000 msecs with max resend 10, current resend 0, timer type 1(2)

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Starting protect timer Rx attach req for 110 
secs

*Feb 23 08:56:35.700: AGW-SessFSM:<100022230001>Authorizing(1) -> Registering(6) on event 
Rx Pre Attach Ack(3) with retcode Authentication Skipped(4)

*Feb 23 08:56:35.700: AGW-SessFSM:<100022230001>Registering(6) -> Registering(6) on event 
Rx Attach Req(12) with retcode Ok(0)

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Creating the sigpak resend details 
0x65F35C00, max resend 10, timeout 10000 msecs, timer type 1(8)

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Starting pak resend timer 0x65F35C00 for 
10000 msecs with max resend 10, current resend 0, timer type 1(8)

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Stopping protect timer Rx attach req

*Feb 23 08:56:35.700: AGW-SessFSM:<100022230001>Registering(6) -> Registering(6) on event 
Tx Attach Rsp(13) with retcode Ok(0)

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Deleting the sigpak resend details 
0x65F35C00

*Feb 23 08:56:35.700: AGW-Sess: <100022230001>Stopping pak resend timer 0x65F35C00 for 
10000 msecs with max resend 10, current resend 0, timer type 1(8)

*Feb 23 08:56:35.700: AGW-SessFSM:<100022230001>Registering(6) -> Ready(7) on event Rx 
Attach Ack(14) with retcode Ok(0)

*Feb 23 08:56:35.700: AGW-SessFSM:<100022230001>Ready(7) -> Ready(7) on event Rx Attach 
Ack(14) with retcode Ok(0)

Here is sample output for R6 FSM Session Events when MS Open fails:

Router#debug wimax agw r6 session fsm events

GW-Sess: <067611141111><(SU)-10.1.1.70>:Link the session to the path

*Feb 23 08:59:07.448: AGW-Sess: <067611141111>Created session

*Feb 23 08:59:07.448: AGW-SessFSM:<067611141111>Idle(0) -> Authorizing(1) on event Rx Pre 
Attach Req(1) with retcode Ok(0)

*Feb 23 08:59:07.448: AGW-Sess: <067611141111>Creating the sigpak resend details 
0x65F35C00, max resend 10, timeout 10000 msecs, timer type 1(2)

*Feb 23 08:59:07.448: AGW-Sess: <067611141111>Starting pak resend timer 0x65F35C00 for 
10000 msecs with max resend 10, current resend 0, timer type 1(2)

*Feb 23 08:59:07.448: AGW-SessFSM:<067611141111>Authorizing(1) -> Authorizing(1) on event 
Tx Pre Attach Rsp(2) with retcode Ok(0)

*Feb 23 08:59:07.448: AGW-Sess: <067611141111>Deleting the sigpak resend details 
0x65F35C00

*Feb 23 08:59:07.448: AGW-Sess: <067611141111>Stopping pak resend timer 0x65F35C00 for 
10000 msecs with max resend 10, current resend 0, timer type 1(2)

*Feb 23 08:59:07.448: AGW-SessFSM:<067611141111>Authorizing(1) -> Authenticating(2) on 
event Rx Pre Attach Ack(3) with retcode Ok(0)

*Feb 23 08:59:07.448: AGW-SessFSM:<067611141111>Authenticating(2) -> Authenticating(2) on 
event Tx EAP Pkt(5) with retcode Ok(0)

*Feb 23 08:59:07.452: AGW-SessFSM:<067611141111>Authenticating(2) -> Authenticating(2) on 
event Rx EAP Pkt(4) with retcode Ok(0)

*Feb 23 08:59:07.452: AGW-Sess: <067611141111>Username pushetty@eap-tls.com, domain is 
eap-tls.com, user is pushetty, delimiter @

*Feb 23 08:59:07.452: AGW-Sess: <067611141111>Found usrgrp eap-tls.com based on domain 
eap-tls.com for user pushetty@eap-tls.com

*Feb 23 08:59:07.456: AGW-SessFSM:<067611141111>Authenticating(2) -> Authenticating(2) on 
event Tx EAP Pkt(5) with retcode Ok(0)

*Feb 23 08:59:07.504: AGW-SessFSM:<067611141111>Authenticating(2) -> Deleting(8) on event 
Auth Result Obtained(7)

*Feb 23 08:59:07.504: AGW-Sess: <067611141111>Creating the sigpak resend details 
0x506F3A88, max resend 10, timeout 10000 msecs, timer type 1(10)

*Feb 23 08:59:07.504: AGW-Sess: <067611141111>Starting pak resend timer 0x506F3A88 for 
10000 msecs with max resend 10, current resend 0, timer type 1(10)

*Feb 23 08:59:07.504: AGW-SessFSM:<067611141111>Deleting(8) -> Deleting(8) on event Tx 
Dereg Req(22) with retcode Ok(0)

*Feb 23 08:59:07.508: AGW-SessFSM:<067611141111>Deleting(8) -> Deleting(8) on event Rx 
Dereg Rsp(23) with retcode Ok(0)

*Feb 23 08:59:07.508: AGW-Sess: <067611141111>Deleting the sigpak resend details 
0x506F3A88

*Feb 23 08:59:07.508: AGW-Sess: <067611141111>Stopping pak resend timer 0x506F3A88 for 
10000 msecs with max resend 10, current resend 0, timer type 1(10)

*Feb 23 08:59:07.508: AGW-SessFSM:<067611141111>Deleting(8) -> Cleanup(9) on event Tx 
Dereg Ack(24) with retcode Ok(0)

Here is sample output for R6 FSM Session Events when the MS successfully closes:

Router#debug wimax agw r6 session fsm events

*Feb 23 08:57:13.696: AGW-SessFSM:<100022230001>Ready(7) -> Deleting(8) on event Rx Dereq 
Req(19) with retcode Ok(0)

*Feb 23 08:57:13.696: AGW-SessFSM:<100022230001>Deleting(8) -> Deleting(8) on event Rx 
Dereq Req(19) with retcode Ok(0)

*Feb 23 08:57:13.696: AGW-Sess: <100022230001>Creating the sigpak resend details 
0x65F35C00, max resend 10, timeout 10000 msecs, timer type 1(11)

*Feb 23 08:57:13.696: AGW-Sess: <100022230001>Starting pak resend timer 0x65F35C00 for 
10000 msecs with max resend 10, current resend 0, timer type 1(11)

*Feb 23 08:57:13.696: AGW-SessFSM:<100022230001>Deleting(8) -> Deleting(8) on event Tx 
DeReg Rsp(20) with retcode Ok(0)

*Feb 23 08:57:13.696: AGW-SessFSM:<100022230001>Deleting(8) -> Cleanup(9) on event Rx 
Dereg Ack(21) with retcode Ok(0)

*Feb 23 08:57:13.696: AGW-Sess: <100022230001>Deleting session with handle 0x9C00000A for 
subscriber handle 0x200000A

*Feb 23 08:57:13.700: AGW-Sess: <100022230001>Deleting the sigpak resend details 
0x65F35C00

*Feb 23 08:57:13.700: AGW-Sess: <100022230001>Stopping pak resend timer 0x65F35C00 for 
10000 msecs with max resend 10, current resend 0, timer type 1(11)

*Feb 23 08:57:13.700: AGW-Sess: <100022230001><(SU)-10.1.1.70>Delink the session from the 
path

*Feb 23 08:57:13.700: AGW-Sess: <100022230001>Deleting session from usergroup

*Feb 23 08:57:13.700: AGW-Sess: <100022230001>Deleting session

debug wimax agw r6 subscriber

To display ASN GW R6 subscriber information, use the debug wimax agw r6 subscriber command in Privileged EXEC mode.

debug wimax agw r6 subscriber [events | errors]

Syntax Description

events	Display information on subscriber creation and deletion.
errors	Display details of any subscriber related errors.

Defaults

There are no default values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

Here is sample R6 Subscriber Events output on a successful MS Open:

Router#debug wimax agw r6 subscriber events

*Feb 23 10:29:03.804: AGW-Subs: <067622242222>Created subscriber with handle 0x29000016

*Feb 23 10:29:03.804: AGW-Subs: <067622242222>Created subscriber

*Feb 23 10:29:03.820: AGW-Subs: <067622242222>Starting subscriber wait for address 
allocation timer for 300 secs

*Feb 23 10:29:03.824: AGW-Subs: <067622242222>Stopping subscriber wait for address 
allocation timer

Here is sample R6 Subscriber Events output on a successful MS Close:

Router#debug wimax agw r6 subscriber events

GW-Subs: <067622272222>Deleting subscriber

*Feb 23 10:27:38.924: AGW-Subs: <067622272222>Deleting a subscriber with handle 0x77000013

debug wimax agw redundancy

To display ASN GW redundancy information, use the debug wimax agw redundancy command in Privileged EXEC mode.

debug wimax agw redundancy [events | errors | tlv | packets]

Syntax Description

events	Displays information on redundancy related events.
errors	Displays information on redundancy related errors.
tlv	Displays information on redundancy related tlvs.
packets	Displays information on redundancy related message dumps in binary.

Defaults

There are no default values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example displays ASN GW redundancy information:

debug wimax agw redundancy events 

Output on ACTIVE ASNGW for MS Open

ASNGW#

*Mar 21 06:25:48.688: AGW-SR: Type AGW_MAC_ID(0), Length 6, Class Mandatory

*Mar 21 06:25:48.688: AGW-SR: Value <067611131111>

*Mar 21 06:25:48.688: AGW-SR: Type AGW_SUB_AUTH_POLICY(1), Length 2, Class Mandatory

*Mar 21 06:25:48.688: AGW-SR: Value <18>

*Mar 21 06:25:48.688: AGW-SR: Type AGW_SUB_AUTH_AK(3), Length 20, Class Optional

*Mar 21 06:25:48.688: AGW-SR: Value <32FE0D9681EBDCFCDA1ECBA65BC764B52D80E90D>

*Mar 21 06:25:48.688: AGW-SR: Type AGW_SUB_AUTH_AK_METHOD(2), Length 4, Class Optional

*Mar 21 06:25:48.688: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_SUB_AUTH_AKID(4), Length 8, Class Optional

*Mar 21 06:25:48.692: AGW-SR: Value <90DDCD514678A29E>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_SUB_AUTH_AKLIFETIME(5), Length 2, Class Optional

*Mar 21 06:25:48.692: AGW-SR: Value <15000>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_SUB_AUTH_CMAC_KEY_COUNT(6), Length 2, Class 
Optional

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_SUB

ASNGW#_AUTH_AK_SEQUENCE_NUM(7), Length 1, Class Optional

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_SUB_AUTH_PMK_SEQUENCE_NUM(8), Length 1, Class 
Optional

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_SUB_AUTH_AK_CONTEXT_PRESENT(9), Length 1, Class 
Optional

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_TID_HASH_KEY(10), Length 14, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0A01014602020202067611131111>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_OUR_TID(11), Length 2, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <32777>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_OUR_TID_FT(12), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <3>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_OUR_TID_MT(13), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <12>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_OUR_PREVIOUS_TID(14), Length 2, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <32776>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_OUR_PREVIOUS_TID_FT(15), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <8>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_OUR_PREVIOUS_TID_MT(16), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <5>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_PEER_TID(17), Length 2, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <9>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_PEER_TID_FT(18), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <9>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_PEER_TID_MT(19), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <8>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_PEER_PREVIOUS_TID(20), Length 2, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <8>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_PEER_PREVIOUS_TID_FT(21), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <8>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_PEER_PREVIOUS_TID_MT(22), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <2>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_ID_CTRL_REMOTE(0), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_ID_CTRL_LOCAL(1), Length 4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <6>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_LOCAL_ADDR_SIG(2), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <33686018>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_REMOTE_ADDR_SIG(3), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <167838022>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_LOCAL_UDPPORT_SIG(4), Length 2, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <2231>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_REMOTE_UDPPORT_SIG(5), Length 2, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <2231>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_FLAG_UNAUTHENTICATED(30), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_FLAG_NW_BEHIND_MS(32), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_FLAG_FRAMED_ROUTE_DOWNLOADED(34), Length 1, 
Clas s Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_MAX_FLOWS_SUPPORTED(33), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_SESSION_TIMEOUT(35), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <15000>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_IDLE_TIMEOUT(36), Length 4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_SESSION_START_TIME(37), Length 8, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0000000010B94FC4>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_SEQ_ENABLED_FOR_SIGNALING(38), Length 1, 
Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_IDS_REQUIRED_SIGNALLING(39), Length 1, 
Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_IDLE_TIMEOUT_DIRECECTION_INBOUND(40), 
Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_READY_FOR_SWITCHING_TRAFFIC(41), Length 1, 
Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_IS_SESSION_SYNCED(42), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_MASTER_SESSION_KEY(31), Length 64, Class 
Optional

*Mar 21 06:25:48.692: AGW-SR: Value 
<F8BA755134ACE79E455CD056001967C4F29BB19A6250B8FA6CFB0981FC880D2F6D59B6419605CB94C0C2099FD
0AB405A2F8BFF0C14867E2C1FEF63D04D4F3365>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_USRGRP_USER_NAME(27), Length 20, Class 
Optional

*Mar 21 06:25:48.692: AGW-SR: Value <7075736865747479406561702D746C732E636F6D>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_USRGRP_DOMAIN_NAME(28), Length 7, Class 
Optional

*Mar 21 06:25:48.692: AGW-SR: Value <2A2A616E792A2A>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_SESSION_ACCT_AAA_AT_CLASS(6), Length 19, Class 
Optional

*Mar 21 06:25:48.692: AGW-SR: Value <636C6173732D77696D61782D6368616E676564>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_PATH_BSID(85), Length 8, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0A01014600000000>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_INDEX(43), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_ID_DATA_LOCAL(45), Length 4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <9>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_ID_DATA_REMOTE(46), Length 4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <26>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_START_TIME(47), Length 8, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0000000010B950B0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_CREATE_TIME(48), Length 8, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0000000000000000>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_FASTSWITCHABLE(49), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SEQ_ENABLED_DATA(50), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_IS_FLOW_SYNCED(51), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_ACCT_SENDING_ACCT_RECORD(73), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_ACCT_PATH_SEND(74), Length 4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_ACCT_LAST_ACCT_RECORD(75), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_ACCT_TERMINATE_CAUSE(76), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_ACCT_AIRLINK_STATE(77), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <2>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_ACCT_ACCT_START_SENT(78), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_ACCT_DISCARD(79), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_ACCT_SESSION_ID(84), Length 4, Class Optional

*Mar 21 06:25:48.692: AGW-SR: Value <17>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_ID(52), Length 4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <18>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_DATA_DELIVERY_SERVICE(53), Length 1, 
Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_LATENCY(54), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <11>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_TRAFFIC_BURST(55), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_TRAFFIC_RATE_SUSTAINED(56), Length 
4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_MIN_TRAFFIC_RATE_RESERVED(57), Length 
4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_POLICY_TRANSMISSION_REQUEST(58), Length 
4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <51>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_SDU_SIZE(59), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <61>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_TOLERATED_JITTER(60), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <71>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_TRAFFIC_PRIORITY(61), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_UNSOLICITED_INTERVAL_GRANT(62), Length 
4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <81>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_UNSOLICITED_INTERVAL_POLLING(63), 
Length 4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_REDUCED_RESOURCES_CODE(64), Length 4, 
Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_MEDIA_FLOW_TYPE(65), Length 0, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_SET_TYPE(66), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_SET_VALUE(67), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_VALID_CFG(68), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_INFO_PRESENT(69), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_CLASSIFIER_PRESENT(70), Length 1, Class 
Mandator y

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_SET_VALUE_PRESENT(71), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_ID(52), Length 4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <17>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_DATA_DELIVERY_SERVICE(53), Length 1, 
Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <2>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_LATENCY(54), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_TRAFFIC_BURST(55), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <2>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_TRAFFIC_RATE_SUSTAINED(56), Length 
4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <3>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_MIN_TRAFFIC_RATE_RESERVED(57), Length 
4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <4>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_POLICY_TRANSMISSION_REQUEST(58), Length 
4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <5>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_SDU_SIZE(59), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <49>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_TOLERATED_JITTER(60), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_TRAFFIC_PRIORITY(61), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_UNSOLICITED_INTERVAL_GRANT(62), Length 
4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_UNSOLICITED_INTERVAL_POLLING(63), 
Length 4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <9>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_REDUCED_RESOURCES_CODE(64), Length 4, 
Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_MEDIA_FLOW_TYPE(65), Length 0, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_SET_TYPE(66), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_SET_VALUE(67), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_VALID_CFG(68), Length 1, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_INFO_PRESENT(69), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_CLASSIFIER_PRESENT(70), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_FLOW_SF_QOS_SET_VALUE_PRESENT(71), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type AGW_FLOW_CURR_TID_USED(23), Length 2, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <32777>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_HOST_ALLOCATED_ADDR(8), Length 4, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <33685507>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_HOST_TABLE_ID(9), Length 2, Class Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <0>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_HOST_ADDR_ALLOC_SOURCE(10), Length 4, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <5>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_HOST_ADDR_REAL_LENGTH(11), Length 2, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <1056>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_HOST_ALLOCATED_PREFIX_LENGTH(12), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <32>

*Mar 21 06:25:48.692: AGW-SR: Type UGW_HOST_AGGREGATE_PREFIX_LENGTH(13), Length 1, Class 
Mandatory

*Mar 21 06:25:48.692: AGW-SR: Value <32>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_ADDR_ORG_TYPE(14), Length 1, Class Mandatory

*Mar 21 06:25:48.696: AGW-SR: Value <1>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_ADDR_TYPE_NUM(15), Length 1, Class Mandatory

*Mar 21 06:25:48.696: AGW-SR: Value <33>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_ADDR_STATIC_ROUTE_ADDED(22), Length 1, Class 
Mandatory

*Mar 21 06:25:48.696: AGW-SR: Value <1>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_ADDR_TYPE_STATIC_ALLOCATED(23), Length 1, 
Class Mandatory

*Mar 21 06:25:48.696: AGW-SR: Value <0>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_ADDR_DYNAMIC_ADDR_ALLOCATED(24), Length 1, 
Class Mandatory

*Mar 21 06:25:48.696: AGW-SR: Value <1>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_ADDR_DYNAMIC_ADDR_REQUEST(25), Length 1, Class 
Mandatory

*Mar 21 06:25:48.696: AGW-SR: Value <0>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_IP_KEY(26), Length 8, Class Mandatory

*Mar 21 06:25:48.696: AGW-SR: Value <0202000300000000>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_DHCP_SERVER_ADDR(16), Length 4, Class Optional

*Mar 21 06:25:48.696: AGW-SR: Value <0>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_DHCP_SERVER_XID(17), Length 4, Class Optional

*Mar 21 06:25:48.696: AGW-SR: Value <5142>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_DHCP_HARDWARE_ADDRESS_TYPE(18), Length 1, 
Class Optional

*Mar 21 06:25:48.696: AGW-SR: Value <1>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_DHCP_HARDWARE_ADDRESS_LEN(19), Length 1, Class 
Optional

*Mar 21 06:25:48.696: AGW-SR: Value <6>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_DHCP_CLIENT_HARDWARE_ADDRESS(20), Length 16, 
Class Optional

*Mar 21 06:25:48.696: AGW-SR: Value <06761113111100000000000000000000>

*Mar 21 06:25:48.696: AGW-SR: Type UGW_HOST_DHCP_CLIENT_ADDR_LEASE_TIME(21), Length 4, 
Class Optional

*Mar 21 06:25:48.696: AGW-SR: Value <3540>

*Mar 21 06:25:48.696: AGW-SR: Attr Type:UGW_HOST_FLOW_INDEX Length: 1 Value: 0

*Mar 21 06:25:48.696: AGW-SR: Attr Type: Length: 1 Value: 1

*Mar 21 06:25:48.696: AGW-SR: 

0C3535E0:                   000003D0 001400A9          ...P...)

0C3535F0: 00000006 06761113 11110001 00020012  .....v..........

0C353600: 00030014 32FE0D96 81EBDCFC DA1ECBA6  ....2~...k\|Z.K&

0C353610: 5BC764B5 2D80E90D 00020004 00000001  [Gd5-.i.........

0C353620: 00040008 90DDCD51 4678A29E 00050002  .....]MQFx".....

0C353630: 3A980006 00020001 00070001 00000800  :...............

0C353640: 01000009 00010100 0A000E0A 01014602  ..............F.

0C353650: 02020206 76111311 11000B00 02800900  ....v...........

0C353660: 0C000103 000D0001 0C000E00 02800800  ................

0C353670: 0F000108 00100001 05001100 02000900  ................

0C353680: 12000109 00130001 08001400 02000800  ................

0C353690: 15000108 00160001 02001500 F3000000  ............s...

0C3536A0: 04000000 00000100 04000000 06000200  ................

0C3536B0: 04020202 02000300 040A0101 46000400  ............F...

0C3536C0: 0208B700 05000208 B7001E00 01000020  ..7.....7...... 

0C3536D0: 00010000 22000100 00210001 01002300  ...."....!....#.

0C3536E0: 0400003A 98002400 04000000 00002500  ...:..$.......%.

0C3536F0: 08000000 0010B94F C4002600 01000027  ......9OD.&....'

0C353700: 00010000 28000100 00290001 01002A00  ....(....)....*.

0C353710: 0100001F 0040F8BA 755134AC E79E455C  .....@x:uQ4,g.E\

0C353720: D0560019 67C4F29B B19A6250 B8FA6CFB  PV..gDr.1.bP8zl{

0C353730: 0981FC88 0D2F6D59 B6419605 CB94C0C2  ..|../mY6A..K.@B

0C353740: 099FD0AB 405A2F8B FF0C1486 7E2C1FEF  ..P+@Z/.....~,.o

0C353750: 63D04D4F 3365001B 00147075 73686574  cPMO3e....pushet

0C353760: 74794065 61702D74 6C732E63 6F6D001C  ty@eap-tls.com..

0C353770: 00072A2A 616E792A 2A000600 13636C61  ..**any**....cla

0C353780: 73732D77 696D6178 2D636861 6E676564  ss-wimax-changed

0C353790: 0016000C 00550008 0A010146 00000000  .....U.....F....

0C3537A0: 0017017C 00000178 002B0001 00002D00  ...|...x.+....-.

0C3537B0: 04000000 09002E00 04000000 1A002F00  ............../.

0C3537C0: 08000000 0010B950 B0003000 08000000  ......9P0.0.....

0C3537D0: 00000000 00003100 01000032 00010000  ......1....2....

0C3537E0: 33000100 00490004 00000001 004A0004  3....I.......J..

0C3537F0: 00000000 004B0004 00000001 004C0001  .....K.......L..

0C353800: 00004D00 0102004E 00010100 4F000100  ..M....N....O...

0C353810: 00540004 00000011 00340004 00000012  .T.......4......

0C353820: 00350001 01003600 04000000 0B003700  .5....6.......7.

0C353830: 04000000 00003800 04000000 00003900  ......8.......9.

0C353840: 04000000 00003A00 04000000 33003B00  ......:.....3.;.

0C353850: 013D003C 00040000 0047003D 00010000  .=.<.....G.=....

0C353860: 3E000400 00005100 3F000400 00000000  >.....Q.?.......

0C353870: 40000400 00000000 41000000 42000100  @.......A...B...

0C353880: 00430001 00004400 01010045 00010100  .C....D....E....

0C353890: 46000101 00470001 00003400 04000000  F....G....4.....

0C3538A0: 11003500 01020036 00040000 00010037  ..5....6.......7

0C3538B0: 00040000 00020038 00040000 00030039  .......8.......9

0C3538C0: 00040000 0004003A 00040000 0005003B  .......:.......;

0C3538D0: 00013100 3C000400 00000000 3D000101  ..1.<.......=...

0C3538E0: 003E0004 00000000 003F0004 00000009  .>.......?......

0C3538F0: 00400004 00000000 00410000 00420001  .@.......A...B..

0C353900: 00004300 01000044 00010100 45000101  ..C....D....E...

0C353910: 00460001 01004700 01000017 00028009  .F....G.........

0C353920: 00180000 00190094 00000090 00080004  ................

0C353930: 02020003 00090002 0000000A 00040000  ................

0C353940: 0005000B 00020420 000C0001 20000D00  ....... .... ...

0C353950: 0120000E 00010100 0F000121 00160001  . .........!....

0C353960: 01001700 01000018 00010100 19000100  ................

0C353970: 001A0008 02020003 00000000 00100004  ................

0C353980: 00000000 00110004 00001416 00120001  ................

0C353990: 01001300 01060014 00100676 11131111  ...........v....

0C3539A0: 00000000 00000000 00000015 00040000  ................

0C3539B0: 0DD40007 00010000 56                 .T......V       

*Mar 21 06:25:48.696: AGW-SR: <067611131111><F[9]>Session (Setup) Sync to Standby

Output on STAND BY ASNGW for MS Open

       Mar  4 20:09:29.224: AGW-SR: 

20135C40:                            001400A9              ...)

20135C50: 00000006 06761112 11110001 00020012  .....v..........

20135C60: 00030014 1EB253DD E845CFF0 C5281F33  .....2S]hEOpE(.3

20135C70: AF951520 22FE51FF 00020004 00000001  /.. "~Q.........

20135C80: 00040008 E0D148B4 9E578601 00050002  ....`QH4.W......

20135C90: 3A980006 00020001 00070001 00000800  :...............

20135CA0: 01000009 00010100 0A000E0A 01014602  ..............F.

20135CB0: 02020206 76111211 11000B00 02800900  ....v...........

20135CC0: 0C000103 000D0001 0C000E00 02800800  ................

20135CD0: 0F000108 00100001 05001100 02000900  ................

20135CE0: 12000109 00130001 08001400 02000800  ................

20135CF0: 15000108 00160001 02001500 F3000000  ............s...

20135D00: 04000000 00000100 04000000 05000200  ...............

jigarsha-asn(co.

20135D10: 04020202 02000300 040A0101 46000400  ............F...

20135D20: 0208B700 05000208 B7001E00 01000020  ..7.....7...... 

20135D30: 00010000 22000100 00210001 01002300  ...."....!....#.

20135D40: 0400003A 98002400 04000000 00002500  ...:..$.......%.

20135D50: 08000000 0010B765 E8002600 01000027  ......7eh.&....'

20135D60: 00010000 28000100 00290001 01002A00  ....(....)....*.

20135D70: 0100001F 00403C9E 68DEDCDD 94126A63  .....@<.h^\]..jc

20135D80: B21697BC 95E0140C E89BFD1D 31DB19B8  2..<.`..h.}.1[.8

20135D90: F95C8E1A ECC83CCE 2F570CD8 176637C4  y\..lH<N/W.X.f7D

20135DA0: D8AD4E43 7DEA7D88 8BDC44DC 35FEFC20  X-NC}j}..\D\5~| 

20135DB0: 679740D4 028B001B 00147075 73686574  g.@T......pushet

20135DC0: 74794065 61702D74 6C732E63 6F6D001C  ty@eap-tls.com..

20135DD0: 00072A2A 616E792A 2A000600 13636C61  ..**any**....cla

20135DE0: 73732D77 696D6178 2D636861 6E676564  ss-wimax-changed

20135DF0: 0016000C 00550008 0A010146 00000000  .....U.....F....

20135E00: 0017017C 00000178 002B0001 00002D00  ...|...x.+....-.

20135E10: 04000000 08002E00 04000000 19002F00  ............../.

20135E20: 08000000 0010B766 C8003000 08000000  ......7fH.0.....

20135E30: 00000000 00003100 01000032 00010000  ......1....2....

20135E40: 33000100 00490004 00000001 004A0004  3....I.......J..

20135E50: 00000000 004B0004 00000001 004C0001  .....K.......L..

20135E60: 00004D00 0102004E 00010100 4F000100  ..M....N....O...

20135E70: 00540004 0000000E 00340004 00000010  .T.......4......

20135E80: 00350001 01003600 04000000 0B003700  .5....6.......7.

20135E90: 04000000 00003800 04000000 00003900  ......8.......9.

20135EA0: 04000000 00003A00 04000000 33003B00  ......:.....3.;.

20135EB0: 013D003C 00040000 0047003D 00010000  .=.<.....G.=....

20135EC0: 3E000400 00005100 3F000400 00000000  >.....Q.?.......

20135ED0: 40000400 00000000 41000000 42000100  @.......A...B...

20135EE0: 00430001 00004400 01010045 00010100  .C....D....E....

20135EF0: 46000101 00470001 00003400 04000000  F....G....4.....

20135F00: 0F003500 01020036 00040000 00010037  ..5....6.......7

20135F10: 00040000 00020038 00040000 00030039  .......8.......9

20135F20: 00040000 0004003A 00040000 0005003B  .......:.......;

20135F30: 00013100 3C000400 00000000 3D000101  ..1.<.......=...

20135F40: 003E0004 00000000 003F0004 00000009  .>.......?......

20135F50: 00400004 00000000 00410000 00420001  .@.......A...B..

20135F60: 00004300 01000044 00010100 45000101  ..C....D....E...

20135F70: 00460001 01004700 01000017 00028009  .F....G.........

20135F80: 00180000 00190094 00000090 00080004  ................

20135F90: 02020002 00090002 0000000A 00040000  ................

20135FA0: 0005000B 00020420 000C0001 20000D00  ....... .... ...

20135FB0: 0120000E 00010100 0F000121 00160001  . .........!....

20135FC0: 01001700 01000018 00010100 19000100  ................

20135FD0: 001A0008 02020002 00000000 00100004  ................

20135FE0: 00000000 00110004 00001415 00120001  ................

20135FF0: 01001300 01060014 00100676 11121111  ...........v....

20136000: 00000000 00000000 00000015 00040000  ...........

20136010: 0DD40007 00010000 56000101 7A        .T......V...z   

Mar  4 20:09:29.228: AGW-SR: Type AGW_MAC_ID(0), Length 6, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <067611121111>

Mar  4 20:09:29.228: AGW-SR: Type AGW_SUB_AUTH_POLICY(1), Length 2, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <18>

Mar  4 20:09:29.228: AGW-SR: Type AGW_SUB_AUTH_AK(3), Length 20, Class Optional

Mar  4 20:09:29.228: AGW-SR: Value <1EB253DDE845CFF0C5281F33AF95152022FE51FF>

Mar  4 20:09:29.228: AGW-SR: Type AGW_SUB_AUTH_AK_METHOD(2), Length 4, Class Optional

Mar  4 20:09:29.228: AGW-SR: Value <1>

Mar  4 20:09:29.228: AGW-SR: Type AGW_SUB_AUTH_AKID(4), Length 8, Class Optional

Mar  4 20:09:29.228: AGW-SR: Value <E0D148B49E578601>

Mar  4 20:09:29.228: AGW-SR: Type AGW_SUB_AUTH_AKLIFETIME(5), Length 2, Class Optional

Mar  4 20:09:29.228: AGW-SR: Value <15000>

Mar  4 20:09:29.228: AGW-SR: Type AGW_SUB_AUTH_CMAC_KEY_COUNT(6), Length 2, Class Optional

Mar  4 20:09:29.228: AGW-SR: Value <1>

Mar  4 20:09:29.228: AGW-SR: Type AGW_SUB_AUTH_AK_SEQUENCE_NUM(7), Length 1, Class 
Optional

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type AGW_SUB_AUTH_PMK_SEQUENCE_NUM(8), Length 1, Class 
Optional

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type AGW_SUB_AUTH_AK_CONTEXT_PRESENT(9), Length 1, Class 
Optional

Mar  4 20:09:29.228: AGW-SR: Value <1>

Mar  4 20:09:29.228: AGW-SR: Type AGW_TID_HASH_KEY(10), Length 14, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0A01014602020202067611121111>

Mar  4 20:09:29.228: AGW-SR: Type AGW_OUR_TID(11), Length 2, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <32777>

Mar  4 20:09:29.228: AGW-SR: Type AGW_OUR_TID_FT(12), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <3>

Mar  4 20:09:29.228: AGW-SR: Type AGW_OUR_TID_MT(13), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <12>

Mar  4 20:09:29.228: AGW-SR: Type AGW_OUR_PREVIOUS_TID(14), Length 2, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <32776>

Mar  4 20:09:29.228: AGW-SR: Type AGW_OUR_PREVIOUS_TID_FT(15), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <8>

Mar  4 20:09:29.228: AGW-SR: Type AGW_OUR_PREVIOUS_TID_MT(16), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <5>

Mar  4 20:09:29.228: AGW-SR: Type AGW_PEER_TID(17), Length 2, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <9>

Mar  4 20:09:29.228: AGW-SR: Type AGW_PEER_TID_FT(18), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <9>

Mar  4 20:09:29.228: AGW-SR: Type AGW_PEER_TID_MT(19), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <8>

Mar  4 20:09:29.228: AGW-SR: Type AGW_PEER_PREVIOUS_TID(20), Length 2, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <8>

Mar  4 20:09:29.228: AGW-SR: Type AGW_PEER_PREVIOUS_TID_FT(21), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <8>

Mar  4 20:09:29.228: AGW-SR: Type AGW_PEER_PREVIOUS_TID_MT(22), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <2>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_ID_CTRL_REMOTE(0), Length 4, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_ID_CTRL_LOCAL(1), Length 4, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <5>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_LOCAL_ADDR_SIG(2), Length 4, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <33686018>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_REMOTE_ADDR_SIG(3), Length 4, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <167838022>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_LOCAL_UDPPORT_SIG(4), Length 2, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <2231>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_REMOTE_UDPPORT_SIG(5), Length 2, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <2231>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_FLAG_UNAUTHENTICATED(30), Length 1, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_FLAG_NW_BEHIND_MS(32), Length 1, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_FLAG_FRAMED_ROUTE_DOWNLOADED(34), Length 1, 
Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_MAX_FLOWS_SUPPORTED(33), Length 1, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <1>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_SESSION_TIMEOUT(35), Length 4, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <15000>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_IDLE_TIMEOUT(36), Length 4, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_SESSION_START_TIME(37), Length 8, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0000000010B765E8>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_SEQ_ENABLED_FOR_SIGNALING(38), Length 1, 
Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_IDS_REQUIRED_SIGNALLING(39), Length 1, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_IDLE_TIMEOUT_DIRECECTION_INBOUND(40), Length 
1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_READY_FOR_SWITCHING_TRAFFIC(41), Length 1, 
Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <1>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_IS_SESSION_SYNCED(42), Length 1, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_MASTER_SESSION_KEY(31), Length 64, Class 
Optional

Mar  4 20:09:29.228: AGW-SR: Value 
<3C9E68DEDCDD94126A63B21697BC95E0140CE89BFD1D31DB19B8F95C8E1AECC83CCE2F570CD8176637C4D8AD4
E437DEA7D888BDC44DC35FEFC20679740D4028B>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_USRGRP_USER_NAME(27), Length 20, Class 
Optional

Mar  4 20:09:29.228: AGW-SR: Value <7075736865747479406561702D746C732E636F6D>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_USRGRP_DOMAIN_NAME(28), Length 7, Class 
Optional

Mar  4 20:09:29.228: AGW-SR: Value <2A2A616E792A2A>

Mar  4 20:09:29.228: AGW-SR: Type UGW_SESSION_ACCT_AAA_AT_CLASS(6), Length 19, Class 
Optional

Mar  4 20:09:29.228: AGW-SR: Value <636C6173732D77696D61782D6368616E676564>

Mar  4 20:09:29.228: AGW-SR: Type UGW_PATH_BSID(85), Length 8, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0A01014600000000>

Mar  4 20:09:29.228: AGW-SR: <067611121111><F[0]>Replacing Local Acct Context Session 
IdReceived From Active: 14

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_INDEX(43), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_ID_DATA_LOCAL(45), Length 4, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <8>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_ID_DATA_REMOTE(46), Length 4, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <25>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_START_TIME(47), Length 8, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0000000010B766C8>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_CREATE_TIME(48), Length 8, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0000000000000000>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_FASTSWITCHABLE(49), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_SEQ_ENABLED_DATA(50), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_IS_FLOW_SYNCED(51), Length 1, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_ACCT_SENDING_ACCT_RECORD(73), Length 4, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <1>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_ACCT_PATH_SEND(74), Length 4, Class Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_ACCT_LAST_ACCT_RECORD(75), Length 4, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <1>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_ACCT_TERMINATE_CAUSE(76), Length 1, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <0>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_ACCT_AIRLINK_STATE(77), Length 1, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <2>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_ACCT_ACCT_START_SENT(78), Length 1, Class 
Mandatory

Mar  4 20:09:29.228: AGW-SR: Value <1>

Mar  4 20:09:29.228: AGW-SR: Type UGW_FLOW_ACCT_DISCARD(79), Length 1, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_ACCT_SESSION_ID(84), Length 4, Class Optional

Mar  4 20:09:29.232: AGW-SR: Value <14>

Mar  4 20:09:29.232: AGW-SR: Type AGW_FLOW_CURR_TID_USED(23), Length 2, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <32777>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_ID(52), Length 4, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <16>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_DATA_DELIVERY_SERVICE(53), Length 1, 
Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_LATENCY(54), Length 4, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <11>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_TRAFFIC_BURST(55), Length 4, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_TRAFFIC_RATE_SUSTAINED(56), Length 
4, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_MIN_TRAFFIC_RATE_RESERVED(57), Length 4, 
Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_POLICY_TRANSMISSION_REQUEST(58), Length 
4, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <51>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_SDU_SIZE(59), Length 1, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <61>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_TOLERATED_JITTER(60), Length 4, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <71>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_TRAFFIC_PRIORITY(61), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_UNSOLICITED_INTERVAL_GRANT(62), Length 
4, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <81>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_UNSOLICITED_INTERVAL_POLLING(63), Length 
4, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_REDUCED_RESOURCES_CODE(64), Length 4, 
Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_MEDIA_FLOW_TYPE(65), Length 0, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_SET_TYPE(66), Length 1, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_SET_VALUE(67), Length 1, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_VALID_CFG(68), Length 1, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_INFO_PRESENT(69), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_CLASSIFIER_PRESENT(70), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_SET_VALUE_PRESENT(71), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_ID(52), Length 4, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <15>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_DATA_DELIVERY_SERVICE(53), Length 1, 
Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <2>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_LATENCY(54), Length 4, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_TRAFFIC_BURST(55), Length 4, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <2>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_MAX_TRAFFIC_RATE_SUSTAINED(56), Length 
4, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <3>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_MIN_TRAFFIC_RATE_RESERVED(57), Length 4, 
Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <4>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_POLICY_TRANSMISSION_REQUEST(58), Length 
4, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <5>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_SDU_SIZE(59), Length 1, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <49>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_TOLERATED_JITTER(60), Length 4, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_TRAFFIC_PRIORITY(61), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_UNSOLICITED_INTERVAL_GRANT(62), Length 
4, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_UNSOLICITED_INTERVAL_POLLING(63), Length 
4, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <9>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_REDUCED_RESOURCES_CODE(64), Length 4, 
Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_MEDIA_FLOW_TYPE(65), Length 0, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_SET_TYPE(66), Length 1, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_SET_VALUE(67), Length 1, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_VALID_CFG(68), Length 1, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_INFO_PRESENT(69), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_CLASSIFIER_PRESENT(70), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_FLOW_SF_QOS_SET_VALUE_PRESENT(71), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_ALLOCATED_ADDR(8), Length 4, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <33685506>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_TABLE_ID(9), Length 2, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_ADDR_ALLOC_SOURCE(10), Length 4, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <5>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_ADDR_REAL_LENGTH(11), Length 2, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1056>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_ALLOCATED_PREFIX_LENGTH(12), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <32>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_AGGREGATE_PREFIX_LENGTH(13), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <32>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_ADDR_ORG_TYPE(14), Length 1, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_ADDR_TYPE_NUM(15), Length 1, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <33>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_ADDR_STATIC_ROUTE_ADDED(22), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_ADDR_TYPE_STATIC_ALLOCATED(23), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_ADDR_DYNAMIC_ADDR_ALLOCATED(24), Length 1, 
Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_ADDR_DYNAMIC_ADDR_REQUEST(25), Length 1, Class 
Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_IP_KEY(26), Length 8, Class Mandatory

Mar  4 20:09:29.232: AGW-SR: Value <0202000200000000>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_DHCP_SERVER_ADDR(16), Length 4, Class Optional

Mar  4 20:09:29.232: AGW-SR: Value <0>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_DHCP_SERVER_XID(17), Length 4, Class Optional

Mar  4 20:09:29.232: AGW-SR: Value <5141>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_DHCP_HARDWARE_ADDRESS_TYPE(18), Length 1, Class 
Optional

Mar  4 20:09:29.232: AGW-SR: Value <1>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_DHCP_HARDWARE_ADDRESS_LEN(19), Length 1, Class 
Optional

Mar  4 20:09:29.232: AGW-SR: Value <6>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_DHCP_CLIENT_HARDWARE_ADDRESS(20), Length 16, 
Class Optional

Mar  4 20:09:29.232: AGW-SR: Value <06761112111100000000000000000000>

Mar  4 20:09:29.232: AGW-SR: Type UGW_HOST_DHCP_CLIENT_ADDR_LEASE_TIME(21), Length 4, 
Class Optional

Mar  4 20:09:29.232: AGW-SR: Value <3540>

Mar  4 20:09:29.232: AGW-SR: <067611121111><F[8]>Subscriber 2.2.0.2 synced from active

debug wimax agw switching

To display ASN GW switching information, use the debug wimax agw switching command in Privileged EXEC mode.

debug wimax agw switching [events | errors | gre events | gre errors | gre packet | gre packet detail | udp events | udp errors | udp packet | udp packet detail | dhcp events | dhcp errors]

Syntax Description

events	Displays information on bearers / signaling related events.
errors	Displays information on bearers / signaling related errors.
gre events	Displays information on bearer GRE related events.
gre errors	Displays information on bearer GRE related errors.
gre packet	Displays information on bearer GRE related packet being switched.
gre packet detail	Displays information on bearer GRE related packet dump being switched.
udp events	Displays information on signaling UDP related events.
udp errors	Displays information on signaling UDP related errors.
udp packet	Displays information on related signaling UDP packet being switched.
udp packet detail	Displays information on related signaling UDP packet dump being switched.
dhcp events	Displays information on IOS DHCP interaction related events.
dhcp errors	Display information on IOS DHCP interaction related errors.

Defaults

There are no default values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example displays various ASN GW switching information:

router#debug wimax agw switching

WiMAX AGW switching events debugging is on

WiMAX AGW switching errors debugging is on

WiMAX AGW switching UDP events debugging is on

WiMAX AGW switching UDP errors debugging is on

WiMAX AGW switching UDP packets debugging is on

WiMAX AGW switching UDP packet detail dump debugging is on

WiMAX AGW switching GRE events debugging is on

WiMAX AGW switching GRE errors debugging is on

WiMAX AGW switching GRE packets debugging is on

WiMAX AGW switching GRE packet detail dump debugging is on

WiMAX AGW switching DHCP events debugging is on

WiMAX AGW switching DHCP errors debugging is on

WiMAX AGW switching DHCP packets debugging is on

WiMAX AGW switching DHCP packet detail dump debugging is on

The following sample output illustrates an MS Open:

*Aug 30 22:52:44.012: AGW-UDP: <100022270001><(SU)-10.1.1.70>PROCESS Downstream Session 
Signal:Sending UDP 54 bytes pak

*Aug 30 22:52:44.012: AGW-UDP: <100022270001><(SU)-10.1.1.70>PROCESS Downstream Session 
Signal:Sending UDP 81 bytes pak

*Aug 30 22:52:44.012: AGW-UDP: <100022270001><(SU)-10.1.1.70>PROCESS Downstream Flow 
Signal:Sending UDP 252 bytes pak

*Aug 30 22:52:44.016: AGW-UDP: <100022270001><(SU)-10.1.1.70>PROCESS Downstream Flow 
Signal:Sending UDP 28 bytes pak

*Aug 30 22:52:44.016: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>CEF Upstream Et0/0:Rcvd 
GRE 646 bytes with flags crKss, version 0x0, procotol 0x800

*Aug 30 22:52:44.016: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>CEF Upstream Vi2:Rcvd 
604(646) byte pak, TOS 0X0

*Aug 30 22:52:44.016: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Upstream 
Et0/0:Rcvd GRE 646 bytes with flags crKss, version 0x0, procotol 0x800

*Aug 30 22:52:44.016: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Upstream Et0/0 
Inner pak 646 bytes pak(retval 0x0, is_ours 1)

contiguous pak, size 646

         AA BB CC 03 34 00 AA BB CC 03 35 00 08 00 45 00

         02 78 00 11 00 00 FD 2F AB FB 0A 01 01 46 02 02

         02 02 20 00 08 00 00 00 00 05 45 00 02 5C 00 4B

         00 00 FE 11 B0 3C 05 05 05 05 FF FF FF FF 00 44

         00 43 02 48 32 06 01 01 ...

*Aug 30 22:52:44.016: AGW-DHCP: <100022270001>PROCESS Upstream DHCP from MS:IP 
Src=5.5.5.5, IP Dst=255.255.255.255, gi=0.0.0.0, len=584, sfid=ox9

*Aug 30 22:52:44.016: AGW-DHCP: <100022270001>PROCESS Upstream Decode DHCP 
DISCOVER:len=576, ci=0.0.0.0, gi=0.0.0.0, si=0.0.0.0, yi=0.0.0.0, sfid=0x9(9)

*Aug 30 22:52:44.016: AGW-DHCP: <100022270001>PROCESS Upstream Options for DHCP DISCOVER : 
53(1),57(2),61(7),12(13),55(5),255(0),

*Aug 30 22:52:44.016: AGW-DHCP: <100022270001>PROCESS Upstream Added Option 82 Subscriber 
ID: 1000.2227.0001, Circuit ID: 9

*Aug 30 22:52:44.016: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Upstream 
Vi2:Rcvd 620(662) bytes pak, TOS 0X0

*Aug 30 22:52:44.016: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Upstream GRE 
pak Rcvd 620(662) bytes pak

contiguous pak, size 620

         45 00 02 6C 00 4B 00 00 FE 11 A9 D4 02 02 02 02

         0B 01 01 5D 00 44 00 43 02 58 9C 40 01 01 06 00

         00 00 08 33 00 00 80 00 00 00 00 00 00 00 00 00

         00 00 00 00 02 02 02 02 10 00 22 27 00 01 00 00

         00 00 00 00 00 00 00 00 ...

asn#

*Aug 30 22:52:44.600: %RADIUS-4-RADIUS_DEAD: RADIUS server 1.8.91.8:1645,1646 is not 
responding.

*Aug 30 22:52:44.600: %RADIUS-4-RADIUS_ALIVE: RADIUS server 1.8.91.8:1645,1646 is being 
marked alive.

asn#

*Aug 30 22:52:46.032: AGW-DHCP: <100022270001>PROCESS Downstream DHCP to MS:IP 
Src=2.2.2.2, IP Dst=2.2.2.2, len=308

*Aug 30 22:52:46.032: AGW-DHCP: <100022270001>PROCESS Downstream Decode DHCP 
OFFER:len=300, ci=0.0.0.0, gi=2.2.2.2, si=0.0.0.0, yi=2.2.0.89, sfid=0x9(9)

*Aug 30 22:52:46.032: AGW-DHCP: <100022270001>PROCESS Downstream Options for DHCP OFFER : 
53(1),54(4),51(4),58(4),59(4),1(4),82(14),255(0),

*Aug 30 22:52:46.032: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Downstream 
Received 328 bytes pak

contiguous pak, size 328

         45 00 01 48 00 0A 00 00 FF 11 BA 9B 00 00 00 00

         FF FF FF FF 00 43 00 44 01 34 9D 5D 02 01 06 00

         00 00 08 33 00 00 80 00 00 00 00 00 02 02 00 59

         00 00 00 00 00 00 00 00 10 00 22 27 00 01 00 00

         00 00 00 00 00 00 00 00 ...

*Aug 30 22:52:46.032: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Downstream 
Vi2:Sending 356(328) bytes pak, TOS 0X0

*Aug 30 22:52:46.032: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Downstream 
Vi2:GRE packet of 356 bytes

contiguous pak, size 356

         45 00 01 64 00 0D 00 00 FF 2F AB 13 02 02 02 02

         0A 01 01 46 20 00 08 00 00 00 00 05 45 00 01 48

         00 0A 00 00 FF 11 BA 9B 00 00 00 00 FF FF FF FF

         00 43 00 44 01 34 9D 5D 02 01 06 00 00 00 08 33

         00 00 80 00 00 00 00 00 ...

*Aug 30 22:52:46.040: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>CEF Upstream Et0/0:Rcvd 
GRE 646 bytes with flags crKss, version 0x0, procotol 0x800

*Aug 30 22:52:46.040: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>CEF Upstream Vi2:Rcvd 
604(646) byte pak, TOS 0X0

*Aug 30 22:52:46.040: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Upstream 
Et0/0:Rcvd GRE 646 bytes with flags crKss, version 0x0, procotol 0x800

*Aug 30 22:52:46.040: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Upstream Et0/0 
Inner pak 646 bytes pak(retval 0x0, is_ours 1)

contiguous pak, size 646

         AA BB CC 03 34 00 AA BB CC 03 35 00 08 00 45 00

         02 78 00 12 00 00 FD 2F AB FA 0A 01 01 46 02 02

         02 02 20 00 08 00 00 00 00 05 45 00 02 5C 00 4D

         00 00 FE 11 B0 3A 05 05 05 05 FF FF FF FF 00 44

         00 43 02 48 3D 19 01 01 ...

*Aug 30 22:52:46.040: AGW-DHCP: <100022270001>PROCESS Upstream DHCP from MS:IP 
Src=5.5.5.5, IP Dst=255.255.255.255, gi=0.0.0.0, len=584, sfid=ox9

*Aug 30 22:52:46.040: AGW-DHCP: <100022270001>PROCESS Upstream Decode DHCP 
REQUEST:len=576, ci=0.0.0.0, gi=0.0.0.0, si=0.0.0.0, yi=0.0.0.0, sfid=0x9(9)

*Aug 30 22:52:46.040: AGW-DHCP: <100022270001>PROCESS Upstream Options for DHCP REQUEST : 
53(1),57(2),61(7),54(4),50(4),51(4),12(13),55(5),255(0),

*Aug 30 22:52:46.040: AGW-DHCP: <100022270001>PROCESS Upstream Added Option 82 Subscriber 
ID: 1000.2227.0001, Circuit ID: 9

*Aug 30 22:52:46.040: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Upstream 
Vi2:Rcvd 620(662) bytes pak, TOS 0X0

*Aug 30 22:52:46.040: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Upstream GRE 
pak Rcvd 620(662) bytes pak

contiguous pak, size 620

         45 00 02 6C 00 4D 00 00 FE 11 A9 D2 02 02 02 02

         0B 01 01 5D 00 44 00 43 02 58 9E F9 01 01 06 00

         00 00 08 33 00 00 80 00 00 00 00 00 00 00 00 00

         00 00 00 00 02 02 02 02 10 00 22 27 00 01 00 00

         00 00 00 00 00 00 00 00 ...

*Aug 30 22:52:46.044: AGW-DHCP: <100022270001>PROCESS Downstream DHCP to MS:IP 
Src=2.2.2.2, IP Dst=2.2.2.2, len=313

*Aug 30 22:52:46.044: AGW-DHCP: <100022270001>PROCESS Downstream Decode DHCP ACK:len=305, 
ci=0.0.0.0, gi=2.2.2.2, si=0.0.0.0, yi=2.2.0.89, sfid=0x9(9)

*Aug 30 22:52:46.044: AGW-DHCP: <100022270001>PROCESS Downstream Options for DHCP ACK : 
53(1),54(4),51(4),58(4),59(4),12(13),1(4),82(14),255(0),

*Aug 30 22:52:46.044: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Downstream 
Received 333 bytes pak

contiguous pak, size 333

         45 00 01 4D 00 0B 00 00 FF 11 BA 95 00 00 00 00

         FF FF FF FF 00 43 00 44 01 39 13 30 02 01 06 00

         00 00 08 33 00 00 80 00 00 00 00 00 02 02 00 59

         00 00 00 00 00 00 00 00 10 00 22 27 00 01 00 00

         00 00 00 00 00 00 00 00 ...

*Aug 30 22:52:46.044: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Downstream 
Vi3:Sending 361(333) bytes pak, TOS 0X0

*Aug 30 22:52:46.044: AGW-GRE: <100022270001><(DG)-10.1.1.70><F[5]>PROCESS Downstream 
Vi3:GRE packet of 361 bytes

asn#

contiguous pak, size 361

         45 00 01 69 00 0E 00 00 FF 2F AB 0D 02 02 02 02

         0A 01 01 46 20 00 08 00 00 00 00 05 45 00 01 4D

         00 0B 00 00 FF 11 BA 95 00 00 00 00 FF FF FF FF

         00 43 00 44 01 39 13 30 02 01 06 00 00 00 08 33

         00 00 80 00 00 00 00 00 ...

*Aug 30 22:52:46.044: AGW-UDP: <100022270001><(SU)-10.1.1.70>PROCESS Downstream Flow 
Signal:Sending UDP 274 bytes pak

*Aug 30 22:52:46.048: AGW-UDP: <100022270001><(SU)-10.1.1.70>PROCESS Downstream Flow 
Signal:Sending UDP 28 bytes pak

debug wimax agw vtemplate

To display ASN GW vtemplate information, use the debug wimax agw vtemplate command in Privileged EXEC mode. Use the no version of the command to turn off debugging.

debug wimax agw vtemplate [events | errors]

no debug wimax agw vtemplate

Syntax Description

events	Displays information on Virtual-template related events.
errors	Displays information on Virtual-template related errors.

Defaults

There are no default values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example displays ASN GW vtemplate information:

router#debug wimax agw vtemplate events

dhcp gateway address

To specify the IP address of the DHCP relay which the server is supposed to communicate with in the AGW, use the dhcp gateway address command in user group configuration mode. Use the no form of the command to revert to the default gateway IP address..

dhcp gateway address gateway-address

no dhcp gateway address gateway-address

Syntax Description

gateway-address

Specifies the IP address of the DHCP Relay. The IP address specified as the gateway address must be the IP address of the AGW Virtual-Template (either primary or one of the secondary IP addresses).

Defaults

By default the AGW VT primary IP address is used.

Command Modes

User group configuration mode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

The IP address specified as the gateway address must be the IP address of the AGW Virtual-Template (either primary or one of the secondary IP addresses).

Examples

The following example illustrates how to configure DHCP relay using the dhcp gateway address command:

Router(config-gw-ug)# dhcp gateway address gateway-address

Related Commands

Command	Description
dhcp server primary	Specifies the external DHCP server used for DHCP IP address allocation.

direction

To specify the direction of the service-flow the configuration is done, and to enter a subcommand mode use the direction command in service flow configuration subcommand mode. Use the no version of this command to remove the corresponding configuration from the direction specified.

direction {uplink | downlink}

Syntax Description

uplink	Service Flow Uplink direction configuration commands.
downlink	Service Flow Downlink direction configuration commands.

Defaults

There are no default values.

Command Modes

Service flow configuration subcommand mode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example specifies the service flow direction to the uplink:

router(config-gw-sf)#direction uplink

encapsulation agw

To clone a Virtual-Access interface of encapsulation type ASNGW, use the encapsulation agw command in Virtual-Template configuration mode.

encapsulation agw

Syntax Description

This command has no arguments or keywords.

Defaults

There are no default values.

Command Modes

Interface configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example enables you to clone a Virtual-Access interface of encapsulation type ASNGW:

Router(config-if)#encapsulation agw

ip access-group

To specify IPv4 access permissions between a subscriber and an external host through the ASNGW at a particular access point, use the ip access-group command in user group configuration mode. Use the no form of the command to disable the input access list.

access-group access-group-number {in | out}

Syntax Description

access-group-number	Specifies the access group number.
in	Filters packets going to the subscriber (downstream).
out	Filters packets coming from the subscriber (upstream).

Defaults

There are no default values.

Command Modes

User group configuration mode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example enables access group number 4:

access-group 4 in

ip address allocation subscriber timeout

To specify the IP address allocation timeout value for a subscriber, use the ip address allocation subscriber timeout command in user group configuration subcommand mode. Use the no form of the command to disable this feature.

ip address allocation subscriber timeout timeout-value-in-secs

Syntax Description

timeout-value-in-secs

Specifies the IP address allocation timeout value. The default value is 300 seconds.

Defaults

The default value is 300 seconds.

Command Modes

User group configuration mode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

After successful data-path establishment between BS and AGW, the address allocation timer is started for timeout value specified by this command[else default value is used]. If within the timeout value, the DHCP process is not successful then the subscriber is automatically de-registered by AGW.

Examples

The following example configures a timeout value of 500 seconds:

Router(config-gw-ug)#ip address allocation subscriber timeout 500

maximum-latency

To configure the time period between the reception of a packet by the BS or MS on its network interface, and the delivery of the packet to the RF Interface of the peer device, use the maximim-latency subcommand in service flow qos info configuration submode. Use the no form of the command to ????

maximum-latency maximum-latency-value

Syntax Description

maximum-latency-value

Specifies the time between the reception of a packet by the BS or MS on its network interface, and the delivery of the packet to the RF Interface of the peer device. Default value is 0.

Defaults

Default value is 0.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

If configured, this parameter represents a service commitment (or admission criteria) at the BS or MS and is guaranteed by the BS or MS. A BS or MS does not have to meet this service commitment for service flows that exceed their minimum reserved rate.

Examples

The following examples configure a maximum latency value of 1 and 11:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

wimax agw service-flow qos-info profile isf-qos-uplink  

 data-delivery-service unsolicited-grant  

 maximum-latency 11  

 maximum-traffic-burst 21  

 maximum-traffic-rate-sustained 31  

 minimum-traffic-rate-reserved 41  

 policy-transmission-request 51  

 sdu-size 61  

 tolerated-jitter 71  

 traffic-priority 3  

 unsolicited-interval-grant 81  

 unsolicited-interval-polling 91

! 

wimax agw service-flow qos-info profile downlink-qos-02  

 data-delivery-service real-time-variable-rate  

 media-flow-type 05abcd

maximum-traffic-burst

To configure the the maximum burst size that the service flow can accommodate, use the maximum-traffic-burst subcommand in service flow qos information configuration submode. Use the no form of the command to disable this feature.

maximum-traffic-burst maximum-traffic-burst-value

Syntax Description

maximum-traffic-burst-value

Specifies the maximum burst size of the service flow. Default values is 0.

Defaults

Default values is 0.

Command Modes

Service flow qos information configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Since the physical speed of ingress/egress ports, the air interface, and the backhaul are greater than the maximum sustained traffic rate parameter for a service, this parameter describes the maximum continuous burst the system should accommodate for the service. This assumes the service is not currently using any of its available resources.

Examples

The following examples configure a maximum traffic burst size of 2 and 21:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

wimax agw service-flow qos-info profile isf-qos-uplink  

 data-delivery-service unsolicited-grant  

 maximum-latency 11  

 maximum-traffic-burst 21  

 maximum-traffic-rate-sustained 31  

 minimum-traffic-rate-reserved 41  

 policy-transmission-request 51  

 sdu-size 61  

 tolerated-jitter 71  

 traffic-priority 3  

 unsolicited-interval-grant 81  

 unsolicited-interval-polling 91

! 

wimax agw service-flow qos-info profile downlink-qos-02  

 data-delivery-service real-time-variable-rate  

 media-flow-type 05abcd

maximum-traffic-rate-sustained

To define the peak information rate of the service flow, use the maximum-traffic-rate-sustained subcommand in service flow qos information configuration submode. Use the no form of the command to disable this feature.

maximum-traffic-rate-sustained maximum-traffic-rate-sustained-value

Syntax Description

maximum-traffic-rate- sustained-value

Specifies the peak information rate of the service flow. The rate is expressed in bits per second, and pertains to the SDUs at the input of the system. The range is 0-4294967295 measured in bits per second

Defaults

There is no default value.

Command Modes

Service flow qos information configuration subcommand.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Explicitly, this parameter does not include MAC overhead such as MAC headers or CRCs. This parameter does not limit the instantaneous rate of the service since this is governed by the physical attributes of the ingress port. If this parameter is omitted or set to zero, then there is no explicitly mandated maximum rate. This field specifies only a boundary, not a guarantee that the rate is available.

Examples

The following example specifies different maximum-traffic-rate-sustained values:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

wimax agw service-flow qos-info profile isf-qos-uplink  

 data-delivery-service unsolicited-grant  

 maximum-latency 11  

 maximum-traffic-burst 21  

 maximum-traffic-rate-sustained 31  

 minimum-traffic-rate-reserved 41  

 policy-transmission-request 51  

 sdu-size 61  

 tolerated-jitter 71  

 traffic-priority 3  

 unsolicited-interval-grant 81  

 unsolicited-interval-polling 91

! 

wimax agw service-flow qos-info profile downlink-qos-02  

 data-delivery-service real-time-variable-rate  

 media-flow-type 05abcd

media-flow-type

To configure the parameter that describes the application type that is used as a hint in admission decisions (for instance, VoIP, video, PTT, gaming, etc.), use the media-flow-type subcommand in service flow qos information configuration submode. Use the no form of the command to ?????

media-flow-type media-flow-type-hex-string

no media-flow-type

Syntax Description

media-flow-type-hex- string

Specifies the application type that is used as a hint in admission decisions. Application types include VoIP, video, PTT, gaming, etc.

Defaults

There are no default values.

Command Modes

Service flow qos information configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example configures two differnt media-flow-type values:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

wimax agw service-flow qos-info profile isf-qos-uplink  

 data-delivery-service unsolicited-grant  

 maximum-latency 11  

 maximum-traffic-burst 21  

 maximum-traffic-rate-sustained 31  

 minimum-traffic-rate-reserved 41  

 policy-transmission-request 51  

 sdu-size 61  

 tolerated-jitter 71  

 traffic-priority 3  

 unsolicited-interval-grant 81  

 unsolicited-interval-polling 91

! 

wimax agw service-flow qos-info profile downlink-qos-02  

 data-delivery-service real-time-variable-rate  

 media-flow-type 05abcd

minimum-traffic-rate-reserved

To specify the minimum rate reserved for a specific service flow use the minimum-traffic-rate- reserved subcommand in service flow qos information configuration submode. Use the no form of the command to disable this feature.

minimum-traffic-rate-reserved minimum-traffic-rate-reserved-value

no minimum-traffic-rate-reserved minimum-traffic-rate-reserved-value

Syntax Description

minimum-traffic-rate- reserved-value

Specifies the minimum rate reserved for this service flow. The rate is expressed in bits per second, and specifies the minimum amount of data transported on behalf of the service flow when averaged over time.

Defaults

There are no default values.

Command Modes

Service flow qos information configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

The specified rate is only honored when sufficient data is available for scheduling. When sufficient data does not exist, the available data is transmitted as soon as possible.

Examples

The following example configures a minimum-traffic-rate-reserved value of 4:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

pak-classify-rule

To specify which packet classification rule profile is associated under the corresponding direction, use the pak-classify-rule subcommand in service flow direction configuration submode. Use the no version of the command to remove the packet classification rule from the corresponding direction.

pak-classify-rule pak-classify-rule-profile-name

Syntax Description

pak-classify-rule- profile-name

Specifies the name of the packet classification rule profile.

Defaults

There are no default values.

Command Modes

Service flow direction configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example specifies a packet classification rule profile named "uplink2":

router(config-gw-sf-dir)#pak-classify-rule uplink2

policy-transmission-request

To specify options for PDU formation, for uplink service flows, and to configure restrictions on the types of bandwidth request options that may be used, use the policy-transmission-request subcommand in service flow QoS information configuration submode. An attribute is enabled by setting the corresponding bit position to 1. Use the no form of the command to ????

policy-transmission-request policy-transmission-request-value

Syntax Description

policy-transmission- request-value

Specifies the value of the policy transmission request. Range of values is 0-4294967295 32-bit bitmask. •Bit #0 Service flow shall not use broadcast bandwidth request opportunities.(Uplink only) •Bit #1 Reserved. •Bit #2 The service flow shall not piggyback requests with data (Uplink only). •Bit #3 The service flow shall not fragment data. •Bit #4 The service flow shall not suppress payload headers (CS parameter). •Bit #5 The service flow shall not pack multiple SDUs (or fragments) into single MAC PDUs. •Bit #6 The service flow shall not include CRC in the MAC PDU. •All other bit positions are reserved.

Defaults

There are no default values.

Command Modes

Service flow QoS information configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

An attribute is enabled by setting the corresponding bit position to 1.

Examples

The following example illustrates how to configure the policy-transmission-request subcommand:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

wimax agw service-flow qos-info profile isf-qos-uplink  

 data-delivery-service unsolicited-grant  

 maximum-latency 11  

 maximum-traffic-burst 21  

 maximum-traffic-rate-sustained 31  

 minimum-traffic-rate-reserved 41  

 policy-transmission-request 51  

 sdu-size 61  

 tolerated-jitter 71  

 traffic-priority 3  

 unsolicited-interval-grant 81  

 unsolicited-interval-polling 91

! 

wimax agw service-flow qos-info profile downlink-qos-02  

 data-delivery-service real-time-variable-rate  

 media-flow-type 05abcd

priority permit

To configure a packet classification rule under the profile, use the priority permit subcommand in packet classify rule submode. Use the no form of the command to unconfigure the packet classification rule.

priority permit {0-255 | gre | tcp | icmp | udp | ip} {src-address src-mask | any | host src-address} [range src-port-low [src-port-high] {dst-address dst-mask | any | host dst-address} [range dst-port-low [dst-port-high][tos tos-low tos-mask tos-high]

no priority permit

Syntax Description

0-255	Specifies the priority of the packet classification rule.
gre	Specifies gre as the packet classification.
tcp	Specifies tcp as the packet classification.
icmp	Specifies icmp as the packet classification.
udp	Specifies udp as the packet classification.
ip	Specifies ip as the packet classification.
src-address	Specifies the src address.
src-mask	Specifies the src mask.
any	Specifies any address or mask.
host	Specifies the host src address.
src-port-low	Specifies the src low port value.
src-port-high	Specifies the src high port value.
dst-address	Specifies the dst address.
dst-mask	Specifies the dst mask.
tos-low	Specifies the tos low value.
tos-mask	Specifies the tos mask.
tos-high	Specifies the tos high value.

Defaults

The default is to use the ISF (Initial Service Flow) to send the packet.

Command Modes

Packet classify rule configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Each packet classification rule should have a unique priority associated with it. Each flow can have zero or more classifier rules. The higher the priority, the higher is the rule precendence. If a packet matches a rule, the corsponding flow is chosent to send that packet.

Examples

The following example sets the priority for a gre packet:

Router(config-gw-pak-classify-rule)#priority permit 100 gre

qos-info

To specify which QoS information profile is associated under the corresponding direction, use the qos-info subcommand in service flow direction configuration submode. Use the no version of the command to remove the QoS information from the corresponding direction.

qos-info qos-profile-name

Syntax Description

qos-profile-name

Specifies the name of the QoS infomation profile.

Defaults

There are no default values.

Command Modes

Service flow direction configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example illustrates how to configure the qos-info command:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

radius-server vsa send accounting wimax

To enable WiMAX RADIUS VSAs to be sent in accounting requests (Start, Int, Stop) from the ASNGW, use the radius-server vsa send accounting wimax command in global configuration mode. Use the no form of the command to disable this feature.

radius-server vsa send accounting wimax

no radius-server vsa send accounting wimax

Syntax Description

There are no arguments or keywords.

Defaults

This feature is disabled by default.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example enables RADIUS VSAs to be sent in accounting requests from the ASNGW:

Router(config)#radius-server vsa send accounting wimax

radius-server vsa send authentication wimax

To enable the WiMAX RADIUS VSAs to be sent out in authentication requests (Access-Request) from the ASNGW, use the radius-server vsa send authentication wimax command in global configuration mode. Use the no form of the command to disable this feature.

radius-server vsa send authentication wimax

no radius-server vsa send authentication wimax

Syntax Description

There are no keywords or arguments.

Defaults

There are no default values.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example enables the ASNGW to send RADIUS VSAs out in authentication requests:

Router(config)#radius-server vsa send authentication wimax

reduced-resources-code

To configure the code that indicates that the requesting entity will accept reduced resources if the requested resources are not available, use the reduced-resources-code subcommand in service flow QoS information configuration submode. Use the no formof the command to disable this function.

reduced-resources-code reduced-resources-code-value

no reduced-resources-code

Syntax Description

reduced-resources-code-value

Specifies the value of the reduction in resources.

Defaults

There is no default value.

Command Modes

Service flow QoS information configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example illustrates how to configure the reduced-resources-code command:

router(config-gw-sf-qos-info)#reduced-resources-code reduced-resources-code-value

reference-point r6

To configure various R6 parameters, including keepalive, base station path and response configuration commands, use the reference-point r6 subcommand in base station group configuration submode. Use the no form of the command to disable these parameters.

reference-point r6 [keepalive | path {purge-timeout value} | response]

no reference-point r6

Syntax Description

keepalive	Enables the AGW-BS keepalive feature.
path	Specifies the WiMAX AGW BS R6 reference point base station path.
purge-timeout value	Specifies WiMAX AGW BS R6 reference point path purge timeout value. As soon as the last session associated with the BS path goes away, the path purge timer is started to remove the path after the timer expiry. The timeout value is measured in minutes. If the purge timer is not configured, the default value is 24 hours.
response	Enables WiMAX AGW BS R6 reference point response configuration commands.

Defaults

The timeout value is measured in minutes. If the purge timer is not configured, the default value is 24 hours.

Command Modes

Base station group configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example illustrates how to configure the reference-point r6 command, and sets a purge- timeout value of 30 minutes:

router(config)#wimax agw base-station group default

router(config-wimax-agw-bs)#reference-point r6 ?

  keepalive  Enable AGW-BS keepalive feature

  path       WiMAX AGW BS R6 reference point base station path

  response   WiMAX AGW BS R6 reference point response configuration commands

router(config-wimax-agw-bs)#reference-point r6 path ?

  purge-timeout  WiMAX AGW BS R6 reference point path purge timeout

router(config-wimax-agw-bs)#reference-point r6 path purge-timeout ?

  <1-4320>  WiMAX AGW BS R6 reference point path purge timeout in minutes

router(config-wimax-agw-bs)#reference-point r6 path purge-timeout 30

reference-point r6 response retransmits

To specify the number of times the AGW attempts to re-send R6 messages when it does not receive a response from the BS, use the reference-point r6 response retransmits command in base station configuration submode. Use the no form of the command to disable this feature.

reference-point r6 response retransmits retransmit value

no reference-point r6 response retransmits

Syntax Description

retransmit value

Specifies the number of times the AGW attempts to resend R6 messages after no response from the BS. The default value is 5.

Defaults

The default value is 5.

Command Modes

Base station configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

The action taken on the maximum retries being reached depends on the timer that expired.

Examples

The following example illustrates the default behavior for the reference-point r6 response retransmits command:

Router(bs-config)#reference-point r6 response retransmits 5

reference-point r6 response timeout

To configure the amount of time the AGW waits for a response from the BS after a request has been sent, use the reference-point r6 response timeout command in base station configuration submode. Use the no form of the command to reset the timeout value to its default value of 5 seconds.

reference-point r6 response timeout timeout value

[no] reference-point r6 response timeout timeout value

Syntax Description

timeout value

Specifies the amount of time the AGW waits for a response from the BS after a request has been sent. The value is measured in seconds. The default value is 5 seconds.

Defaults

The default value is 5 seconds.

Command Modes

Base station configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

If a response is not received within the configured interval, the AGW will retransmit the message until the maximum number of retries configured is reached.

Examples

The following example illustrates that the AGW waits for a response from the BS for 10 seconds :

router (config) #reference-point r6 response timeout 10

sdu-size

To configure the parameter that represents the number of bytes in the fixed size Service Data Unit (SDU), use the sdu-size subcommand in service flow QoS information configuration submode. Use the no form of the command to disable this feature.

sdu-size sdu-size-value

no sdu-size

Syntax Description

sdu-size-value

Specifies the number of bytes in the fixed size SDU. You can use this parameter for a UGS service flow when the length of IP packets on the data plane is fixed, and known in advance (this is typically the case for flows generated by a specific codec). The range is 0-255. The default value is 49 bytes.

Defaults

The sdu-size-value default value is 49 bytes.

Command Modes

Service flow QoS information configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example illustrates how to configure the sdu-size command:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

wimax agw service-flow qos-info profile isf-qos-uplink  

 data-delivery-service unsolicited-grant  

 maximum-latency 11  

 maximum-traffic-burst 21  

 maximum-traffic-rate-sustained 31  

 minimum-traffic-rate-reserved 41  

 policy-transmission-request 51  

 sdu-size 61  

 tolerated-jitter 71  

 traffic-priority 3  

 unsolicited-interval-grant 81  

 unsolicited-interval-polling 91

! 

wimax agw service-flow qos-info profile downlink-qos-02  

 data-delivery-service real-time-variable-rate  

 media-flow-type 05abcd

security subscriber address-filtering ingress

To enable the Ingress address filtering for the subscriber, use the security subscriber address-filtering ingress command in user group configuration mode. Use the no form of the command to disable Ingress address filtering.

security subscriber address-filtering ingress

Syntax Description

There are no keywords or arguments.

Defaults

The feature is disabled.

Command Modes

User group configuration mode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

When enabled in the upstream path, the source IP address in the packet is verified against the allowed set of addresses that are allocated to the subscriber, or Hosts behind the subscriber, or Framed route attribute (if downloaded from the AAA server). If the source IP address does not match, the packet is dropped for the subscriber.

Examples

The following example enables the security subscriber address-filtering ingress command:

Router(config-gw-ug)#security subscriber address-filtering ingress

service-flow pre-defined profile

To specify the number of pre-defined service flows to be opened for a subscriber, use the service-flow pre-defined profile command in user group configuration mode. Use the no form of the command to disable predefined service flows.

service-flow pre-defined {isf | secondary secondary-index} profile sf-profile-name

Syntax Description

isf	The service flow is assumed to be the initial service flow.
secondary secondary-index	Represents the auxiliary service flows for the subscriber.
profile sf-profile-name	Enables the service flow profile and profile name of the flow.

Defaults

There are no default values.

Command Modes

User group configuration mode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Currently 1 initial service flow and 1 secondary service flow is allowed per subscriber. Each service flow can be associated with a pre-configured service flow for QoS and packet classification rule parameters in the uplink and downlink direction.

Examples

The following example enables the initial service flow:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

set

To specify what DSCP or TOS marking needs to be applied for the subscriber packets in the downstream direction, use the set subcommand in service flow direction configuration submode. Use the no form of the command to disable this feature. By default no marking is done.

set {dscp | precedence} {precedence-value | dscp-value}

no set {dscp | precedence}

Syntax Description

dscp	Set GW service flow DSCP specific values.
precedence	Set GW serive flow Precedence specific values.
precedence-value	Precedence value. The range is 0-7.
dscp-value	Differentiated services codepoint value. The range is 0-63.

Defaults

By default, no marking is don. Default values of above values ?????

Command Modes

Service flow direction configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example specifies the precedence-value and dscp-value arguments:

router(config-gw-sf-dir)#set dscp dscp-value

dscp-value -   

  <0-63>   Differentiated services codepoint value

  af11     Match packets with AF11 dscp (001010)

  af12     Match packets with AF12 dscp (001100)

  af13     Match packets with AF13 dscp (001110)

  af21     Match packets with AF21 dscp (010010)

  af22     Match packets with AF22 dscp (010100)

  af23     Match packets with AF23 dscp (010110)

  af31     Match packets with AF31 dscp (011010)

  af32     Match packets with AF32 dscp (011100)

  af33     Match packets with AF33 dscp (011110)

  af41     Match packets with AF41 dscp (100010)

  af42     Match packets with AF42 dscp (100100)

  af43     Match packets with AF43 dscp (100110)

  cs1      Match packets with CS1(precedence 1) dscp (001000)

  cs2      Match packets with CS2(precedence 2) dscp (010000)

  cs3      Match packets with CS3(precedence 3) dscp (011000)

  cs4      Match packets with CS4(precedence 4) dscp (100000)

  cs5      Match packets with CS5(precedence 5) dscp (101000)

  cs6      Match packets with CS6(precedence 6) dscp (110000)

  cs7      Match packets with CS7(precedence 7) dscp (111000)

  default  Match packets with default dscp (000000)

  ef       Match packets with EF dscp (101110)

router(config-gw-sf-dir)#set precedence precedence-value

<0-7>           Precedence value

  critical        Set packets with critical precedence (5)

  flash           Set packets with flash precedence (3)

  flash-override  Set packets with flash override precedence (4)

  immediate       Set packets with immediate precedence (2)

  internet        Set packets with internetwork control precedence (6)

  network         Set packets with network control precedence (7)

  priority        Set packets with priority precedence (1)

  routine         Set packets with routine precedence (0)

service wimax agw

To enable the ASN gateway functionality on the router, use the service wimax agw command in global configuration mode. Use the no version of the command to disable ASN gateway functionality; all configured ASN gateway-specific command lines will also be removed.

service wimax agw

no service wimax agw

Syntax Description

There are no arguments or keywords.

Defaults

There are no default values.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

The no version of the command will disable the ASN gateway functionality and all the configured ASN gateway specific command lines will be removed. The no version of the command will be allowed only if there no session being serviced on the ASN gateway.

Examples

The following example enables the ASN gateway:

(config)#service wimax agw

show ip slb sessions

To display information about sessions handled by Cisco IOS Server Load Balancing (IOS SLB), use the show ip slb sessions command in privileged EXEC mode.

show ip slb sessions [gtp | gtp-inspect | ipmobile | radius] [vserver virtual-server] [client ip-address netmask] [asnr6] [detail]

Syntax Description

gtp	(Optional) Displays information about general packet radio service (GPRS) Tunneling Protocol (GTP) sessions being handled by IOS SLB.
gtp-inspect	(Optional) Displays information about GTP sessions being handled by IOS SLB that have GTP cause code inspection enabled.
ipmobile	(Optional) Displays information about Mobile IP sessions being handled by IOS SLB.
radius	(Optional) Displays information about RADIUS sessions being handled by IOS SLB.
vserver virtual-server	(Optional) Displays information about sessions being handled by the specified virtual server.
client ip-address netmask	(Optional) Displays information about sessions associated with the specified client IP address or subnet.
asnr6	(Optional) Displays information about ASN sessions.
detail	(Optional) Displays detailed information.

Command Modes

Privileged EXEC

Command History

Release	Modification
12.1(11b)E	This command was introduced.
12.2(14)S	This command was integrated into Cisco IOS Release 12.2(14)S.
12.1(13)E3	The gtp and gtp-inspect keywords were added.
12.2(14)ZA2	The ipmobile keyword was added.
12.2(18)SXE	This command was integrated into Cisco IOS Release 12.2(18)SXE.
12.2(33)SRA	This command was integrated into Cisco IOS Release 12.2(33)SRA
12.4(15)XL	The asnr6 keyword was added.

Examples

The following is sample output from the show ip slb sessions command for ASN sessions:

router# show ip slb session asnr6

vserver         MSID              Base Station      real             state

------------------------------------------------------------------------------10.10.10.10     
001646013fc0      5.5.5.5           10.10.1.1        ASNR6_REQ

router# show ip slb session asnr6 detail

   ASN, client = 12.12.12.1:2231, virtual = 3.3.3.3:2231

   state = ASNR6_ESTAB, real = 2.2.2.2

   Key = 0000000100020003, retry = 1

show wimax agw

To display various system parameters, including ASN GW software version, number of base stations allowed, number of subscribers allowed, and others, use the show wimax agw privilege EXEC command.

show wimax agw

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

The output of this show command contains the following information:

•Version of WiMAX AGW Software

•Maximum number of base stations allowed

•Maximum number of subscribers allowed

•Number of base stations currently connected

•Number of R6 sessions currently active

•Number of flows currently active

•Current base station keep alive interval configured

•Current timeout value configured for R6 messages

Examples

The following is sample output for the show wimax agw command:

WiMAX AGW Session Redundancy is enabled

		WiMAX AGW Session Redundancy system status

		 AGW state = ACTIVE	

		 AGW-peer state = STANDBY HOT	

		WiMAX AGW Session Redundancy Statistics Summary

                		Synced to standby

		  Subscriber               1

		  Flows                    2			

		  Hosts                    3

Display information about the AGW redundancy specific statistics.

Snapshot:

			WiMAX AGW Session Redundancy Counters

			Redundancy Events Counters On Active

			Session Events

			Session Up Success               : 100

			Session Down Success             : 10

			Flow Events

			Flow Up Success                  : 200

			Flow Down Success	      : 0

			Host Events

			Host Up Success                  : 300

			Host Down Success                : 100

			Authentication Events

			Re-authentication Update Success : 10

			Accounting Events

			Accounting Update Success 

show wimax agw message

To display information about the messages supported by the AGW, use the show wimax agw message command in privileged EXEC mode.

show wimax agw message [function-type-no]

Syntax Description

function-type-no

Funtion type value of the message to be displayed .

Defaults

No default behavior or values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

If a Function-Type number is not specified, then the command displays information about all the supported Function-Types.

The output of this show command contains the following information:

•Function-Type number

•Name of the Function-Type

•Possible reference points over which this Function-Type can be received

•Number of possible message types for this Function-Type

•Details for each message type, which include

•Message-Type number

•Message-Type name

•Reference points over which this Message-Type can be received

•Whether a reply is expected for this Message-Type

Examples

The following is sample output for the show wimax agw message [function-type-no] command:

Message function type Data Path(3/0x3)

 Highest message type value 16

 Reference pts on which rcvd/sent BS <-> AGW R6(8)

  Message type Deregistration Request(4/0x4)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Deregistration Response(5/0x5)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Deregistration Ack(6/0x6)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

  Message type Registration Request(12/0xC)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Registration Response(13/0xD)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Registration Ack(14/0xE)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

Message function type Context Delivery(4/0x4)

ASNGW#sh wimax agw message 

Message function type Data Path(3/0x3)

 Highest message type value 16

 Reference pts on which rcvd/sent BS <-> AGW R6(8)

  Message type Deregistration Request(4/0x4)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Deregistration Response(5/0x5)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Deregistration Ack(6/0x6)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

  Message type Registration Request(12/0xC)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Registration Response(13/0xD)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Registration Ack(14/0xE)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

Message function type Context Delivery(4/0x4)

 Highest message type value 4

 Reference pts on which rcvd/sent BS <-> AGW R6(8)

  Message type Context Delivery Request(1/0x1)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Context Delivery Report(2/0x2)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

Message function type Auth Relay(8/0x8)

 Highest message type value 10

 Reference pts on which rcvd/sent BS <-> AGW R6(8)

  Message type EAP Start(1/0x1)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

  Message type EAP Transfer(2/0x2)

Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

  Message type Key Change Directive(5/0x5)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Key Change Confirm(6/0x6)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Key Change ACK(7/0x7)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

  Message type CMAC Key Count Update(8/0x8)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type CMAC Key Count Update Ack(9/0x9)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

Message function type MS State Change(9/0x9)

 Highest message type value 18

 Reference pts on which rcvd/sent BS <-> AGW R6(8)

  Message type Attachment Response(7/0x7)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Attachment Request(8/0x8)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Attachment ACK(9/0x9)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

  Message type Pre Attachment Request(15/0xF)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Pre Attachment Response(16/0x10)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Pre Attachment ACK(17/0x11)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

Message function type Keepalive(20/0x14)

 Highest message type value 3

 Reference pts on which rcvd/sent BS <-> AGW R6(8)

  Message type Keepalive Request(1/0x1)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Expecting response for this message

  Message type Keepalive Response(2/0x2)

   Reference pts on which rcvd/sent BS <-> AGW R6(8)

   Not expecting response for this message

show wimax agw path

To display base station information, use the show wimax agw path command in privileged EXEC mode.

show wimax agw path [bs-ip-address] [brief]

Syntax Description

bs-ip-address

For each base station, the following information will be displayed. •Control path details •BS IP Address •Number of sessions currently active •Number of packets and bytes transmitted to the base station •Number of packets and bytes received from the base station •Data path details •BS IP Address •Number of flows currently active •Number of packets and bytes switched in CEF and process paths for this base station If the base station IP address is not specified, the command will display information about all of the base stations currently connected to the AGW.

brief

If the brief keyword is specified, then the output will contain a list of all the current sessions in column format, containing the following information •BS IP Address •Number of sessions currently active •Number of flows currently active

Defaults

No default behavior or values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Examples

The following is sample output for the show wimax agw path command:

router# show wimax agw path

Path type Sig-UDP

 State current Ready, old Purging

 Number of sessions connected 1

 Number of old sessions connected 0

 Address local 2.2.2.2(AF_INET), remote 10.1.1.71(AF_INET)

 UDP port local 2231(0x8B7), remote 2231(0x8B7)

 Identification Peer 0x0A01014700000000, Our 0x02020202

 Traffic sent 5 packets, 609 bytes

 Traffic received 5 packets, 482 bytes

Path type Data-GRE

 Number of flows connected 1

 Address local 2.2.2.2(AF_INET), remote 10.1.1.71(AF_INET)

 Traffic sent 0 packets, 0 bytes

 Traffic received 3 packets, 1938 bytes

show wimax agw redundancy

To show various system parameters, including ASN GW software version, number of base stations allowed, number of subscribers allowed, and others, use the show wimax agw privilege EXEC command.

show wimax agw redundancy [ status]

no show wimax agw redundancy

Syntax Description

status

(Optional) Displays session redundancy status on the ASN GW.

Defaults

No default behavior or values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Examples

The following is sample output for the show wimax agw redundancy status command:

Router#show wimax agw redundancy status

           WiMAX AGW Session Redundancy is enable

           WiMAX AGW Session Redundancy system status

           AGW state = STANDBY HOT

           AGW-peer state = ACTIVE

           WiMAX AGW Session Redundancy Status Summary

                        Synced from active

           Subscriber            1

           Flows                 2

           Hosts                 0

show wimax agw statistics

To display statistics per reference point, use the show wimax agw statistics command in privileged EXEC mode.

---

Note For Release 1.0 of the AGW, only a single reference point, R6 is supported.

---

show wimax agw statistics

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

For each reference point, the following information will be displayed

•Number of function types (FT) and message types (MT) sent over this reference point

•Number of function types (FT) and message types (MT) received over this reference point

Examples

The following is sample output for the show wimax agw statistics command:

Router#show wimax agw statistics

Message function type MS State Change(9/0x9)

  Message type Attachment Response(7/0x7)

   Number of messages sent 4

   Number of messages received 0

   Number of messages resent 0

  Message type Attachment Request(8/0x8)

   Number of messages sent 0

   Number of messages received 4

   Number of messages resent 0

  Message type Attachment ACK(9/0x9)

   Number of messages sent 0

   Number of messages received 4

   Number of messages resent 0

  Message type Pre Attachment Request(15/0xF)

   Number of messages sent 0

   Number of messages received 4

   Number of messages resent 0

  Message type Pre Attachment Response(16/0x10)

   Number of messages sent 4

   Number of messages received 0

   Number of messages resent 0

  Message type Pre Attachment ACK(17/0x11)

   Number of messages sent 0

   Number of messages received 4

   Number of messages resent 0

Data Path Statistics

Router#show wimax agw statistics

Message function type Data Path(3/0x3)

  Message type Deregistration Request(4/0x4)

   Number of messages sent 1

   Number of messages received 1

   Number of messages resent 0

  Message type Deregistration Response(5/0x5)

   Number of messages sent 1

   Number of messages received 0

   Number of messages resent 0

  Message type Deregistration Ack(6/0x6)

   Number of messages sent 0

   Number of messages received 1

   Number of messages resent 0

  Message type Registration Request(12/0xC)

   Number of messages sent 8

   Number of messages received 1

   Number of messages resent 0

  Message type Registration Response(13/0xD)

   Number of messages sent 1

   Number of messages received 8

   Number of messages resent 0

  Message type Registration Ack(14/0xE)

   Number of messages sent 8

   Number of messages received 1

   Number of messages resent 0

show wimax agw subscriber

To display subscriber information, use the show wimax agw subscriber command in privileged EXEC mode. If the subscriber macid is not specified, the output displays information about all the subscribers currently connected to the AGW.

show wimax agw subscriber [msid macid] [brief | host | flow] [traffic]

Syntax Description

msid	Displays information about the mobile subscriber.
macid	If the subscriber macid is not specified, the output displays information about all the subscribers currently connected to the AGW.
brief	Displays output that contains a list of all the subscribers currently connected. Contains the following information: •Subscriber MACID •Local/remote IP addresses of the signaling end points for this subscriber •Local/remote UDP ports of the signaling end points for this subscriber •Number of flows currently active
flow
host
traffic

Defaults

No default behavior or values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

The following information will be displayed for each subscriber.

•Subscriber MACID

•Local/remote IP addresses of the signaling end points for this subscriber

•Local/remote UDP ports of the signaling end points for this subscriber

•Subscriber FSM information

•Number of flows currently active

•Details for all the flows

•Authentication details (i.e., unauthenticated, single-EAP, double-EAP etc.)

Examples

The following is sample output for the show wimax agw subscriber command:

MSID 1000.2223.0001

 Connection time 044:26:44

 Auth policy 0X0(0)

 Number of TIDs 1

 TID Key 10.1.1.70/2.2.2.2/1000.2223.0001

  Peer TID 0X2(2)

    FT MS State Change(9), MT Attachment Request(8)

  Our TID 0x8002(32770)

    FT Data Path(3), MT Registration Request(12)

 Subscriber address 2.2.0.87, type IPv4, organization IETF

 Subscriber address method Dynamic, source DHCP relay

 Subscriber address assigned on flow downlink ID 1

 Subscriber address prefix len allocated 32, aggregate 32

 Subscriber address traffic sent 0 packets, 0 bytes

 Subscriber address traffic received 3 packets, 1812 bytes

 Subscriber address DHCP XID 2097, server 11.1.1.93, htype 1

 Subscriber address DHCP client ID 1000.2223.0001, length 6

 Subscriber address DHCP Refresh time 86400 seconds

 Number of sessions 1

  Session details:

   FSM in state Ready(7) on last event Rx Attach Ack(14)

   Authentication method unauthenticated

   Associated user group **unauthenticated**

   Signalling address local 2.2.2.2, remote 10.1.1.70

   Signalling UDP port local 2231, remote 2231

   Idle for inbound 08:13:56, outbound 08:13:56

   Ingress Address filtering 0 packets, 0 bytes

   Number of flows 2

    Flow details ISF(0)

     FSM in state SF Ready(4) on last event Up(1)

     Transaction ID used 0X8001(32769)

     Data ID local 0x1(1), remote 0x1(1)

     Data address local 2.2.2.2, remote 10.1.1.70

     Data traffic sent 2 packets, 661 bytes

     Data traffic received 4 packets, 2416 bytes

     Accounting last record sent Interim(3)

     Idle for inbound 1d20h, outbound 1d20h

     Service Flow information Downlink:

      Identifier 1

      QoS information:

       Data-delivery-service real-time-variable-rate

       Minimum traffic-rate-reserved 4, Maximum latency 1

       Unsolicited interval-polling 9, Traffic-priority 1

       Maximum traffic-rate-sustained 3, Request/Transmission-policy 5

       Maximum traffic-burst-rate 2

       Reduced-resources-code 0

     Classifier information:

       priority 0 permit ip any any

     Service Flow information Uplink:

      Identifier 2

      QoS information:

       Data-delivery-service unsolicited-grant

       Minimum traffic-rate-reserved 0, Maximum latency 11

       Tolerated-jitter 71, SDU-size 61

       Unsolicited interval-grant 81, Request/Transmission-policy 51

       Reduced-resources-code 0

      Classifier information:

       priority 0 permit ip any any

    Flow details Secondary(1)

     FSM in state SF Ready(4) on last event Up(1)

     Transaction ID used 0X8002(32770)

     Data ID local 0x2(2), remote 0x2(2)

     Data address local 2.2.2.2, remote 10.1.1.70

     Data traffic sent 3 packets, 999 bytes

     Data traffic received 3 packets, 1812 bytes

     Accounting last record sent Interim(3)

     Idle for inbound 08:14:15, outbound 08:14:15

     Service Flow information Downlink:

      Identifier 3

      QoS information:

       Data-delivery-service real-time-variable-rate

       Minimum traffic-rate-reserved 0, Maximum latency 0

       Unsolicited interval-polling 0, Traffic-priority 0

       Maximum traffic-rate-sustained 0, Request/Transmission-policy 0

       Maximum traffic-burst-rate 0

       Reduced-resources-code 0

       Media-flow-type 05abcd

      Classifier information:

       priority 2 permit ip any any

     Service Flow information Uplink:

      Identifier 4

      QoS information:

       Data-delivery-service real-time-variable-rate

       Minimum traffic-rate-reserved 0, Maximum latency 0

       Unsolicited interval-polling 0, Traffic-priority 0

       Maximum traffic-rate-sustained 0, Request/Transmission-policy 0

       Maximum traffic-burst-rate 0

       Reduced-resources-code 0

       Media-flow-type 05abcd

      Classifier information:

       priority 2 permit ip any any

asn# show wimax agw subscriber brief [traffic] 

MSID                Base Station    Pkts-Tx    Bytes-Tx          Pkts-Rx    Bytes-Rx

1000.2223.0001 10.5.5.3              0              0                    0              0                   

1000.2224.0001 10.5.5.3              0              0                    0              0         

asn# show wimax agw subscriber brief flow [traffic] 

 MSSID              Base Station Idx Pkts-Tx  Bytes-Tx        Pkts-Rx    Bytes-Rx

1000.2223.0001 10.5.5.3        0   0               0                    0              0                   

1000.2223.0001 10.5.5.3        1   0               0                    0              0                   

1000.2224.0001 10.5.5.3        0   0               0                    0              0                   

1000.2224.0001 10.5.5.3        1   0               0                    0              0            

Asn# show wimax agw subscriber brief host [traffic] 

MSID                  Base Station    Index Pkts-Tx    Bytes-Tx             Pkts-Rx    
Bytes-Rx

1000.2223.0001 10.5.5.3           1         0                 0                    0          
0                   

1000.2224.0001 10.5.5.3           1         0                 0                    0          
0      

show wimax agw tlv

To display information about the TLVs supported by the AGW, use the show wimax agw command in privileged EXEC mode.

show wimax agw tlv [tlv-type]

Syntax Description

tlv-type

Displays information about the supported TLVs.

Defaults

No default behavior or values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

If a TLV type is not specified, the command will display information on all the supported TLVs.

The output of this show command contains the following information:

•TLV Type

•Name of the TLV

•Minimum and maximum allowed lengths for the TLV

•Number of nested TLVs allowed for the TLV

•Whether this TLV can be nested as part of another TLV

Examples

The following is sample output for the show wimax agw tlv command:

router# show wimax agw tlv

TLV name MS Information(1/0x1)

 Maximum size is 0

 Storage type is Nested

TLV name Base Station Information(2/0x2)

 Maximum size is 0

 Storage type is Nested

TLV name SF Information(3/0x3)

 Maximum size is 0

 Storage type is Nested

TLV name RT-VR Data Delivery Service(5/0x5)

 Maximum size is 0

 Storage type is Nested

TLV name Authentication Complete(6/0x6)

 Maximum size is 0

 Storage type is Nested

TLV name BE Data Delivery Service(7/0x7)

 Maximum size is 0

 Storage type is Nested

TLV name DP Information(8/0x8)

 Maximum size is 0

 Storage type is Nested

TLV name NRT-VR Data Delivery Service(9/0x9)

 Maximum size is 0

 Storage type is Nested

TLV name UGS Data Delivery Service(13/0xD)

 Maximum size is 0

 Storage type is Nested

TLV name ERT-VR Data Delivery Service(14/0xE)

 Maximum size is 0

 Storage type is Nested

TLV name Packet Classification Rule(15/0xF)

 Maximum size is 0

 Storage type is Nested

TLV name AK Context(16/0x10)

 Maximum size is 0

 Storage type is Nested

TLV name Base Station ID(20/0x14)

 Maximum size is 8

 Storage type is Hexadecimal

TLV name Reject Cause Code(21/0x15)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name AK(22/0x16)

 Maximum size is 20

 Storage type is Hexadecimal

TLV name AK Indentifier(23/0x17)

 Maximum size is 8

 Storage type is Hexadecimal

TLV name AK Life Time(24/0x18)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name AK Sequence number(25/0x19)

 Maximum size is 1

 Storage type is Integer - size 1 byte

TLV name Authentication Result(26/0x1A)

 Maximum size is 1

 Storage type is Integer - size 1 byte

TLV name Anchor Gateway ID(27/0x1B)

 Maximum size is 16

 Storage type is Hexadecimal

TLV name Authenticator ID(28/0x1C)

 Maximum size is 16

 Storage type is Hexadecimal

TLV name Classifier Action(30/0x1E)

 Maximum size is 1

 Storage type is Integer - size 1 byte

TLV name Classifier Rule Priority(31/0x1F)

 Maximum size is 1

 Storage type is Integer - size 1 byte

TLV name DP Identifier(GRE Key)(35/0x23)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name Data Path End point Identifier(36/0x24)

 Maximum size is 4

 Storage type is Hexadecimal

TLV name Authorization Policy(40/0x28)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name PKMv2 Message Code(42/0x2A)

 Maximum size is 1

 Storage type is Integer - size 1 byte

TLV name Registration Type(46/0x2E)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name QoS Information(48/0x30)

 Maximum size is 0

 Storage type is Nested

TLV name SDU size(55/0x37)

 Maximum size is 1

 Storage type is Integer - size 1 byte

TLV name Service Flow Identifier(59/0x3B)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name Tolerated jitter(60/0x3C)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name Traffic Priority(61/0x3D)

 Maximum size is 1

 Storage type is Integer - size 1 byte

TLV name Maximum latency(67/0x43)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name Maximum sustained traffic rate(68/0x44)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name Maximum traffic burst(69/0x45)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name Minimum Reserved Traffic Rate(70/0x46)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name Media Flow Type(72/0x48)

 Maximum size is 0

 Storage type is Hexadecimal

TLV name IP destination address and mask(73/0x49)

 Maximum size is 0

 Storage type is Hexadecimal

TLV name IP source address and mask(74/0x4A)

 Maximum size is 0

 Storage type is Hexadecimal

TLV name IP TOS/DSCP range and mask(75/0x4B)

 Maximum size is 3

 Storage type is Hexadecimal

TLV name IP Protocol(82/0x52)

 Maximum size is 0

 Storage type is Hexadecimal

TLV name Protocol destination port range(83/0x53)

 Maximum size is 0

 Storage type is Hexadecimal

TLV name EAP Payload(85/0x55)

 Maximum size is 0

 Storage type is Hexadecimal

TLV name Registration Context(88/0x58)

 Maximum size is 0

 Storage type is Nested

TLV name CMAC Key Count(91/0x5B)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name Combined Resources Required(92/0x5C)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name Context Purpose Indicator(93/0x5D)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name Direction(94/0x5E)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name Key Change Indicator(95/0x5F)

 Maximum size is 1

 Storage type is Integer - size 1 byte

TLV name Protocol source port range(96/0x60)

 Maximum size is 0

 Storage type is Hexadecimal

TLV name Reduced Resources Code(97/0x61)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name Request Or Transmission Policy(98/0x62)

 Maximum size is 4

 Storage type is Integer - size 4 bytes

TLV name Reservation Action(99/0x63)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name Reservation Result(101/0x65)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name Unsolicited Grant Interval(102/0x66)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name Unsolicited Polling Interval(103/0x67)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name CS Type(104/0x68)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name MTG Profile(105/0x69)

 Maximum size is 1

 Storage type is Integer - size 1 byte

TLV name Number of Downlink CIDs(106/0x6A)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name Number of Uplink CIDs(107/0x6B)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

TLV name Number of Uplink Classifiers(108/0x6C)

 Maximum size is 2

 Storage type is Integer - size 2 bytes

show wimax agw user-group

To display information about user groups configured on the ASN GW, use the show wimax age user-group command in Privileged EXEC mode.

show wimax age user-group [any | brief | name | unauthnticated]

Syntax Description

any	(Optional) Displays any user-group details.
brief	(Optional) Displays brief output.
name	(Optional) Displays the user-group name.
unauthnticated	(Optional) Displays unauthenticated user-group details.

Defaults

No default behavior or values.

Command Modes

Privileged EXEC.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

Here is example output for the show wimax agw user-group command:

router# show wimax agw user-group

AGW User-Group-List

There are 3 user-groups configured in list wimax

User group domain name any

 Service mode operational

 Sessions 0 associated

 Traffic Sent 0 packets, 0 bytes

 Traffic Recevied 0 packets, 0 bytes

 Ingress Address filtering 0 packets, 0 bytes

User group domain name cisco

 Service mode operational

 Sessions 0 associated

 Traffic Sent 0 packets, 0 bytes

 Traffic Recevied 0 packets, 0 bytes

 Ingress Address filtering 0 packets, 0 bytes

User group domain name unauthenticated

 Service mode operational

 Sessions 0 associated

 Traffic Sent 0 packets, 0 bytes

 Traffic Recevied 0 packets, 0 bytes

 Ingress Address filtering 0 packets, 0 bytes

router#show wimax agw user-group brief ?

Name            Sessions  Pkts-Tx   Bytes-Tx  Pkts-Rx   Bytes-Rx  VRF

any             0         0         0         0         0                        

cisco           0         0         0         0         0                        

unauthenticated 0         0         0         0         0             

router#show wimax agw user-group any ? 

  brief  Brief output

  |      Output modifiers

  <cr>

router#show wimax agw user-group any 

User group domain name any

--------------------------------------

 Service mode operational

 Sessions 0 associated

 Traffic Sent 0 packets, 0 bytes

 Traffic Recevied 0 packets, 0 bytes

 Ingress Address filtering 0 packets, 0 bytes

router#show wimax agw user-group any brief 

Name            Sessions  Pkts-Tx   Bytes-Tx  Pkts-Rx   Bytes-Rx  VRF

any             0         0         0         0         0                        

router#show wimax agw user-group name ?                

  WORD  Enter User-group Name

router#show wimax agw user-group name cisco ?

  brief  Brief output

  |      Output modifiers

  <cr>

router#show wimax agw user-group name cisco 

User group domain name cisco

--------------------------------------

 Service mode operational

 Sessions 0 associated

 Traffic Sent 0 packets, 0 bytes

 Traffic Recevied 0 packets, 0 bytes

 Ingress Address filtering 0 packets, 0 bytes

router#show wimax agw user-group name cisco brief ?

  |  Output modifiers

  <cr>

router#show wimax agw user-group name cisco brief 

Name            Sessions  Pkts-Tx   Bytes-Tx  Pkts-Rx   Bytes-Rx  VRF

cisco 0         0         0         0         0                        

router#show wimax agw user-group unauthenticated ?

  brief  Brief output

  |      Output modifiers

  <cr>

router#show wimax agw user-group unauthenticated 

User group domain name unauthenticated

--------------------------------------

 Service mode operational

 Sessions 0 associated

 Traffic Sent 0 packets, 0 bytes

 Traffic Recevied 0 packets, 0 bytes

 Ingress Address filtering 0 packets, 0 bytes

asn#sh wimax agw user-group unauthenticated b

asn#sh wimax agw user-group unauthenticated brief ?

  |  Output modifiers

  <cr>

router#show wimax agw user-group unauthenticated brief 

Name            Sessions  Pkts-Tx   Bytes-Tx  Pkts-Rx   Bytes-Rx  VRF

unauthenticated    0         0         0         0           0        

subscriber redundancy rate

To configure broadband subscriber session redundancy policy for synchronization between high availability (HA) active and standby processors, use the subscriber redundancy command in global configuration mode. To delete the policy, use the no form of this command.

subscriber redundancy [bulk limit cpu percentage delay seconds allow value] [dynamic limit cpu percentage delay seconds allow value] [delay time] [rate sessions time]

no subscriber redundancy

Syntax Description

bulk limit cpu	(Optional) Configures bulk synchronization redundancy policy.
dynamic	(Optional) Configures dynamic synchronization redundancy policy.
limit cpu percentage	(Optional) Specifies CPU busy threshold value as a percentage. Range 0 to 100, default 90.
delay seconds	(Optional) Specifies delay in seconds before the CCM component synchronizes sessions after the CPU busy threshold is exceeded.
allow value	(Optional) Specifies the minimum number of sessions to synchronize once the CPU busy threshold is exceeded and the specified delay is met. Range is 1 to 2,147,483,637, default is 25.
delay time	(Optional) Specifies minimum amount of time in seconds that a session must be ready before dynamic synchronization occurs. Range is 1 to 33,550.
rate sessions time	(Optional) Specifies number of sessions per time period for bulk and dynamic synchronization. •sessions—Range 1 to 32,000, default is 250. •time—Range in seconds is 1 to 33,550, default is 1.

Command Default

Subscriber redundancy policy applies default values.

Command Modes

Global configuration.

Command History

Release	Modification
12.2(31)SB2	This command was introduced.

Usage Guidelines

Cisco IOS HA functionality for broadband protocols and applications allows for stateful switchover (SSO) and in service software upgrade (ISSU) features that minimize planned and unplanned downtime and failures. HA uses the cluster control manager (CCM) to manage the capability to synchronize subscriber session bring up on the standby processor of a redundant processor system. Use the subscriber redundancy bulk command to create and modify redundancy policy used during bulk (startup) synchronization. Use the subscriber redundancy dynamic command to tune subscriber redundancy policies that throttle dynamic synchronization by monitoring CPU usage and sync rates. Use the subscriber redundancy delay command to establish session duration minimums for synchronization and manage dynamic syncing of short duration calls. Use the subscriber redundancy rate command to throttle the number of sessions to be synchronized per period.

Examples

The following example configures 300 sessions to be synchronized per second during bulk and dynamic synchronization:

router(config)# subscriber redundancy rate 300 1

timeout idle

To specify the idle timeout for a subscriber, use the timeout idle command in user group configuration mode. Use the no form of the command to disable this feature.

timeout idle timeout value [inbound]

Syntax Description

timeout value	Value in seconds of the idle timeout. Timeout value range is 1 to 4294967 seconds. There is no default timeout value, it must be specified in the configuration.
inbound	Assumes the subscriber is idle if no upstream traffic is seen for the specified period of time.

Defaults

There are no default values. The timeout value must be specified in the configuration.

Command Modes

User group configuration mode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

When configured, the timer starts. If no traffic is seen for the subscriber over the session for specified period of time, then the subscriber is removed by sending a de-registration to the base station. If inbound is configured, the subscriber is assumed to idle if no upstream traffic is seen for the specified period of time. By default, the idle timeout feature is disabled. The idle timeout value can be downloaded from the AAA server as well, and if downloaded the AAA value is given precedence over the configured value.

Examples

The following example illustrates the timeout idle command:

router(config-gw-ug)#timeout idle 15

timeout session

To specify the session or absolute timeout value for a subscriber, use the timeout session command in user group configuration submode. Use the no form of the command to delete the timeout session values for a subscriber.

timeout session timeout value

no timeout session

Syntax Description

timeout value

Specifies the timeout session value in seconds. The timeout value range is 1 to 4294967 seconds. There is no default timeout value, it must be specified in the configuration.

Defaults

The session timeout feature is disabled by default. The timeout value range is 1 to 4294967 seconds. There is no default timeout value, it must be specified in the configuration.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

When configured, the session timeout timer is started on the successful authentication of authenticated calls, or when the traffic path is ready for unauthenticated calls. Upon successful reauthentication, the timer is restarted.

Examples

The following example configures a session timeout value of 3600 seconds:

router(config-gw-ug)#timeout session 3600

tolerated-jitter

To configure the maximum delay variation (jitter) for the service flow connection, use the tolerated-jitter subcommand in service flow QoS information configuration submode. Use the no form of the command to disable this function.

tolerated-jitter tolerated-jitter-value

no tolerated-jitter tolerated-jitter-value

Syntax Description

tolerated-jitter-value

Specifies the maximum delay variation value for the service flow connection. The range is 0-4294967295 measured in bits per second

Defaults

There are no default values.

Command Modes

Service flow QoS information configuration submode.

Command History

Release	Modification
12.4(15)XL

Examples

The following example illustrates the tolerated jitter command:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

wimax agw service-flow qos-info profile isf-qos-uplink  

 data-delivery-service unsolicited-grant  

 maximum-latency 11  

 maximum-traffic-burst 21  

 maximum-traffic-rate-sustained 31  

 minimum-traffic-rate-reserved 41  

 policy-transmission-request 51  

 sdu-size 61  

 tolerated-jitter 71  

 traffic-priority 3  

 unsolicited-interval-grant 81  

 unsolicited-interval-polling 91

! 

wimax agw service-flow qos-info profile downlink-qos-02  

 data-delivery-service real-time-variable-rate  

 media-flow-type 05abcd

traffic-priority

To specify the priority assigned to a service flow, use the traffic-priority subcommand in service flow QoS information configuration submode. Use the no form of the command to disable the command.

traffic-priority traffic-priority-value

no traffic-priority

Syntax Description

traffic-priority-value

Specifies the priority value assigned to a service flow. The range is 0-7. Higher numbers indicate higher priority. Default value is 0.

Defaults

Default value is 0.

Command Modes

Service flow QoS information configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

If two service flows are identical in all QoS parameters except priority, the higher priority service flow is given lower delay, and higher buffering preference. For non-identical service flows, the priority parameter does not take precedence over any conflicting service flow QoS parameter. The specific algorithm for enforcing this parameter is not mandated here.

Examples

The following example sets the service flow priority value to 1 and 3:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

wimax agw service-flow qos-info profile isf-qos-uplink  

 data-delivery-service unsolicited-grant  

 maximum-latency 11  

 maximum-traffic-burst 21  

 maximum-traffic-rate-sustained 31  

 minimum-traffic-rate-reserved 41  

 policy-transmission-request 51  

 sdu-size 61  

 tolerated-jitter 71  

 traffic-priority 3  

 unsolicited-interval-grant 81  

 unsolicited-interval-polling 91

! 

wimax agw service-flow qos-info profile downlink-qos-02  

 data-delivery-service real-time-variable-rate  

 media-flow-type 05abcd

unsolicited-interval-grant

To specifies the nominal interval between successive data grant opportunities for this service flow, use the unsolicited-interval-grant command in service flow QoS information configuration submode. Use the no form of the command to disable this feature.

unsolicited-interval-grant unsolicited-interval-grant-value

no unsolicited-interval-grant

Syntax Description

unsolicited-interval- grant-value

Specifies the nominal interval between successive data grant opportunities for this service flowThis parameter may be used for a UGS and ERT-VR service flow when the inter-arrival time of IP packets on the data plane is known in advance (this is typically the case for flows generated by a specific codec). The range is 0-65535 measured in milliseconds.

Defaults

No default behavior or values.

Command Modes

Service flow QoS information configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Examples

The following example illustrates the use of the unsolicited-interval-grant command:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

wimax agw service-flow qos-info profile isf-qos-uplink  

 data-delivery-service unsolicited-grant  

 maximum-latency 11  

 maximum-traffic-burst 21  

 maximum-traffic-rate-sustained 31  

 minimum-traffic-rate-reserved 41  

 policy-transmission-request 51  

 sdu-size 61  

 tolerated-jitter 71  

 traffic-priority 3  

 unsolicited-interval-grant 81  

 unsolicited-interval-polling 91

! 

wimax agw service-flow qos-info profile downlink-qos-02  

 data-delivery-service real-time-variable-rate  

 media-flow-type 05abcd

unsolicited-interval-polling

To specify the maximal nominal interval between successive polling grant opportunities for a service flow, use the unsolicited-interval-polling command in service flow QoS information configuration submode.

unsolicited-interval-polling unsolicited-interval-polling-value

Syntax Description

unsolicited-interval- polling-value

Specifies the maximal nominal interval between successive polling grant opportunities for a service flow. The range is 0-65535 measured in milliseconds.

Defaults

There are no default values.

Command Modes

Service flow QoS information configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Examples

The following is sample output for the unsolicited-interval-polling command:

wimax agw service-flow qos-info profile isf-qos-downlink  

 data-delivery-service real-time-variable-rate  

 maximum-latency 1  

 maximum-traffic-burst 2  

 maximum-traffic-rate-sustained 3  

 media-flow-type 012041424344  

 minimum-traffic-rate-reserved 4  

 policy-transmission-request 5  

 sdu-size 6  

 tolerated-jitter 7  

 traffic-priority 1  

 unsolicited-interval-grant 8  

 unsolicited-interval-polling 9

wimax agw service-flow qos-info profile isf-qos-uplink  

 data-delivery-service unsolicited-grant  

 maximum-latency 11  

 maximum-traffic-burst 21  

 maximum-traffic-rate-sustained 31  

 minimum-traffic-rate-reserved 41  

 policy-transmission-request 51  

 sdu-size 61  

 tolerated-jitter 71  

 traffic-priority 3  

 unsolicited-interval-grant 81  

 unsolicited-interval-polling 91

! 

wimax agw service-flow qos-info profile downlink-qos-02  

 data-delivery-service real-time-variable-rate  

 media-flow-type 05abcd

user-group (user group list configuration subcommand)

To configure a user group under the user group list, use the user group subcommand in user group list configuration submode.

user-group {any | unauthenticated | domain domain-name}

no user-group {any | unauthenticated | domain domain-name}

Syntax Description

any	Configures any user group - For an authenticated user where no user-group based on the domain is found, they are defaulted into this category. For example, if you receive a user with the NAI "abc@cisco2.com" but do not have a user-group domain for cisco2.com, this user will fall into the any user group category.
unauthenticated	Configures all unauthenticated users of the user groups.
domain	Configures domain based user groups - In cases where the user is authenticated, the AGW will try to discover the user based on the domain name part of the NAI received. The NAI received is expected to be of the format "userpart@domain". In order to match a user-group (for example, abc@cisco.com), you need to configure user-group domain "cisco.com" and put all per-domain configurations under this user-group.
domain-name	Specifies the domain name.

Defaults

There are no default values.

Command Modes

User group list configuration sub mode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Release 1.0 of the Cisco ASN GW supports the user-groups any and unauthenticated.

Examples

The following example illustrates how to configure unauthnticated users:

Router(config-gw-ugl)#user-group unauthenticated

vrf (user group configuration submode)

To configure the VRF, use the vrf command in user group configuration submode. Use the no form of the command to delete the VRF.

vrf vrf-name

no vrf vrf-name

Syntax Description

vrf-name

Specifies the name of the vrf.

Defaults

By default, no user groups belong to any VRF.

Command Modes

User group configuration submode.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

Multiple user groups can share the VRF.

Examples

The following example illustrates how to configure a vrf named "cisco":

Router(config-gw-ug)#vrf cisco

wimax agw base-station group

To configure a base-station group, and to ensure that all of the individual base stations configured to belong to this base station group will use the base station group parameters, use the wimax agw base-station group command in global configuration mode. This command also places you in base station configuration submode. Use the no form of the command to delete a base station group.

wimax agw base-station group name

Syntax Description

name	Specifies the name of the base station group.

Defaults

The default behavior is that there are no base station groups.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Examples

The following example creates a base station group named "cisco":

router(config)#wimax agw base-station group cisco

wimax agw base-station ip-addr any group

To specify the base stations that are allowed to connect to the AGW, and the base station group they belong to,use the wimax agw base-station ip-addr any group command in global configuration mode. Use the no form of the command to disable this feature.

wimax agw base-station ip-addr any group group-name

no wimax agw base-station ip-addr any group group-name

Syntax Description

group-name

Specifies the name of the base station group.

Defaults

There are no default values.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

The base stations are configured based on the IP address of the base station. The mask parameter allows several base stations with contiguous IP addresses to be configured using a single invocation of this command.

Examples

The following example configures a base station group named boston:

Router(config)#wimax agw base-station ip-addr any group boston

wimax agw r6 maximum base-station

To specify the maximum number of base stations that are allowed to connect to the AGW, use the wimax agw r6 maximum base-station command in global confuration mode. Use the no form of the command to disable this feature.

wimax agw r6 maximum base-station number

no wimax agw r6 maximum base-station

Syntax Description

number

Specifies the maximum number of base stations that are allowed to connect to the AGW. The maximum number range is 0-500. The expected throughput per BS will dictate the number of BSs that can connect.

Defaults

The maximum number of base stations that are supported on the AGW platform is 500.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

If you do not configure this command, the number of base stations allowed to connect to the AGW is set to the maximum number supported by the platform.

Examples

The following example allows 240 base stations to connect to the ASN GW:

wimax agw r6 maximum base-station 240

wimax agw r6 maximum subscriber

To specify the maximum number of subscriber sessions allowed on the AGW, use the wimax agw r6 maximum subscriber command in global configuration mode. Use the no form of the command to disable this feature.

wimax agw r6 maximum subscriber number

Syntax Description

number

Specifies the maximum number of subscriber sessions on the ASN GW. The range is 0-20000.

Defaults

The default maximum number of subscriber sessions is 20000

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

If you do not configure this command, the number of subscriber sessions supported on the AGW platform is set to its maximum value.

Examples

The following example limits the number of subscriber sessions on the ASN GW to 50:

Router(config)#wimax agw r6 maximum subscriber 50

wimax agw redundancy

To enable session redundancy on the ASN GW, use the wimax agw redundancy command in global configuration mode. Use the no form of the command to disable this feature. You must clear all subscribers to configure the no form of the command.

wimax agw redundancy

no wimax agw redundancy

Syntax Description

There are no keywords or arguments.

Defaults

This command is disabled by default.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

You must clear all subscribers to configure no wimax agw redundancy. Here is an example:

AGW-2(config)#no wimax agw redundancy

ERROR: Clear all subscribers (1) before unconfig. redundancy

AGW-2(config)#

Examples

The following example enables session redundancy on the ASN GW:

Router(config)# wimax agw redundancy

wimax agw service-flow pak-classify-rule profile

To configure a service-flow packet classification rule profile on the ASN GW, or to enter the service flow packet classify configuration submode, use the wimax agw service-flow pak-classify-rule profile global configuration command. Use the no form of the command to remove the profile, or exit the submode.

Router(config)#

wimax agw service-flow pak-classify-rule profile service-flow-pak-classify-rule-profile-name

no wimax agw service-flow pak-classify-rule profile

Syntax Description

service-flow-pak- classify-rule-profile- name

Specifies the name of the service-flow packet classification rule profile on the ASN GW. The profile name is case insensitive.

Defaults

There are no default values.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

The profiles are configured under the predefined service flows that are opened for the subscriber.

Examples

The following example illustrates a configuration with a service flow named "cisco2":

router(config)wimax agw service-flow pak-classify-rule profile cisco 2

wimax agw service-flow profile

To configure a service-flow profile on the AGW, and to enter the GW service flow profile configuration submode, use the wimax agw service-flow profile command in global configuration mode. Use the no form of the command to disable this feature and remove the profile.

agw service-flow profile service-flow-profile-name

no agw service-flow profile service-flow-profile-name

Syntax Description

service-flow-profile- name

Specifies the name of the service flow profile. The profile name is case insensitive.

Defaults

There are no default values.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

These service flows are predefined and are opened for the subscriber.

Configuring the command will open the GW service flow profile configuration submode.

Examples

The following example illustrates a configuration with a service flow named "cisco2":

agw service-flow profile cisco2

wimax agw service-flow profile qos-info

To configure a service-flow QoS information profile on the AGW, or to enter service flow qos info configuration submode, use the wimax agw service-flow profile qos-info command in global configuration mode. Use the no form of the command to remove the profile.

wimax agw service-flow profile qos-info service-flow-qos-info-profile-name

Syntax Description

service-flow-qos-info- profile-name

Specifies the name of the service flow QoS information profile.

Defaults

There are no default values.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

You can configure a service-flow QoS information profile on the AGW that is associated to predefined service flows that are opened for the subscriber.

Examples

The following example specifies the service flow profile name as "upstreamprofile":

Router(config)#wimax agw service-flow profile qos-info upstreamprofile

wimax agw user group-list

To configure the User group list on the AGW router, and to enter user group list configuration subcommand mode, use the wimax agw user group-list command in global configuration mode. Use the no form of the command to remove the user group lists, or to exit user group list configuration subcommand mode.

wimax agw user group-list user-group-list-name

no wimax agw user group-list user-group-list-name

Syntax Description

user-group-list-name

Specifies the name of the user group list.

Defaults

The default behavior is that there are no configured user group lists.

Command Modes

Global configuration.

Command History

Release	Modification
12.4(15)XL	This command was introduced.

Usage Guidelines

There can be only one user group list allowed on a single processor of the AGW.

The no version of command will remove the user group list. This will create a user group list sub configuration mode to create multiple user groups under the user-group list created.

Examples

The following example configures a user group list named "cisco":

Router(config)#wimax agw user group-list cisco

The wimax agw user group-list command supports route aggregate at per user-group level. The following example shows how to configure route aggregation:

AGW-1(config)#wimax agw user group-list wimax

AGW-1(config-gw-ugl)#user-group unauthenticated

AGW-1(config-gw-ug)#?

GW user group sub configuration commands

  aaa           User group AAA configuration commands

  default       Set a command to its defaults

  dhcp          User group DHCP configuration commands

  exit          Exit user group sub configuration

  ip            User group IP configuration commands

  no            Negate a command or set its defaults

  security      User group security configuration commands

  service-flow  User group service-flow configuration commands

  timeout       User group timeout configuration commands

  vrf           User group VRF configuration commands

AGW-1(config-gw-ug)#ip 

AGW-1(config-gw-ug)#ip ?

  access-group  Specify access control for packets

  address       User group address configuration commands

  route         User group route confiugration commands

AGW-1(config-gw-ug)#ip rou

AGW-1(config-gw-ug)#ip route ?

  aggregate  Configure aggregate range

AGW-1(config-gw-ug)#ip route 

AGW-1(config-gw-ug)#ip route aggregate ?

  A.B.C.D  {/nn || A.B.C.D}  IP prefix and prefix mask

  auto                       will aggregate routes automatically base on the

                             mask return by servers

AGW-1(config-gw-ug)#ip route aggregate auto

AGW-1(config-gw-ug)#