-
Cisco IOS Dial Technologies Command Reference, Release 12.2 T
-
Commands A through CAS
-
Commands CHA through CPP
-
Commands D
-
Commands EN through IP
-
Commands IS through L2
-
Commands LCP through MOD
-
Commands MU through PPP
-
Commands PRI through SHE
-
Commands SHOW A through SHOW DI
-
Commands SHOW DS through SHOW LI
-
Commands SHOW M through SHOW N
-
Commands SHOW P through SHOW R
-
Commands SHOW S through SHOW V
-
Commands SHU through X
-
Index
-
Table Of Contents
subscriber authorization enable
virtual-profile virtual-template
vpdn authorize directed-request
vty-async ipx ppp-client loopback
shutdown (port)
To disable a port, use the shutdown command in port configuration mode. To change the administrative state of a port from out-of-service to in service, use the no form of this command.
shutdown
no shutdown
Syntax Description
This command has no arguments or keywords.
Defaults
Port is enabled.
Command Modes
Port configuration
Command History
Usage Guidelines
The shutdown command disables a port.
Note
The shutdown command is similar to the modem shutdown MICA technologies modem command.
Examples
The following example disables ports 1 to 18 and then reenables them:
router(config)# port 1/1 1/18router(config-port)# shutdownrouter(config-port)# no shutdownRelated Commands
shutdown (spe)
To take a service processing element (SPE) out of service, use the shutdown command in SPE configuration mode. To change the administrative state of this SPE from down to up, use the no form of this command.
shutdown
no shutdown
Syntax Description
This command has no arguments or keywords.
Defaults
SPE is in service.
Command Modes
SPE configuration
Command History
Examples
The following example disables SPE ports 1 to 18 and then reenables them:
router(config)# spe 1/1 1/18router(config-spe)# shutdownrouter(config-spe)# no shutdownRelated Commands
show syscon sdp
To display information about the Shelf Discovery Protocol (SDP), use the show syscon sdp command in privileged EXEC or user EXEC mode.
show syscon sdp
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC
User EXECCommand History
Examples
The following is sample output from the show syscon sdp command:
Router# show syscon sdpCurrent time 10:46:32 PST Jan 28 1998, system controller 172.23.66.100Last hello packet received at 10:45:38 PST Jan 28 199811773 Total SDP packets0 packets with bad MD5 hash5884 Hello packets received5889 Hello packets sent0 Command packets received0 Command packets sentTable 135 describes the fields shown in the sample display.
Related Commands
syscon address
Specifies the system controller for a managed shelf.
syscon source-interface
Specifies the interface to use for the source address in SDP packets.
signaling-class cas
To define a signalling class with a template formed by directives guiding the Call Service Module (CSM) to process the digit sequence, use the signaling-class cas command in global configuration mode. To remove the signalling class assignment, use the no form of this command.
signaling-class cas name
no signaling-class cas name
Syntax Description
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
Usage Guidelines
The signalling class is referred by the name argument.
Examples
The following example enables the signaling-class cas command:
signaling-class cas testprofile incoming S<*a<*d<*ncontroller T1 1/0/1cas-custom 1class testRelated Commands
class (controller)
Activates the signaling-class cas command.
Defines a template formed by directives guiding the CSM to process the digit sequence for a signaling class.
snapshot client
To configure a client router for snapshot routing, use the snapshot client command in interface configuration mode. To disable a client router, use the no form of this command.
snapshot client active-time quiet-time [suppress-statechange-updates] [dialer]
no snapshot client active-time quiet-time [suppress-statechange-updates] [dialer]
Syntax Description
Defaults
Snapshot routing is disabled.
The active-time and quiet-time arguments have no default values.
Command Modes
Interface configuration
Command History
Usage Guidelines
The value of the active-time argument must be the same for the client and server routers.
To specify that the remote server routers be called by this client router during each active period, use the dialer map snapshot command.
Examples
The following example configures a client router for snapshot routing:
interface dialer 1snapshot client 5 600 suppress-statechange-updates dialerRelated Commands
snapshot server
To configure a server router for snapshot routing, use the snapshot server command in interface configuration mode. To disable a server router, use the no form of this command.
snapshot server active-time [dialer]
no snapshot server active-time [dialer]
Syntax Description
Defaults
Snapshot routing is disabled.
The active-time argument has no default value.
Command Modes
Interface configuration
Command History
Usage Guidelines
The value of the active-time argument must be the same for the client and server routers.
Examples
The following example configures a server router for snapshot routing:
interface dialer 1snapshot server 5Related Commands
Displays snapshot routing parameters associated with an interface.
Configures a client router for snapshot routing.
source-ip
To specify an alternate IP address for a virtual private dialup network (VPDN) tunnel that is different from the physical IP address used to open the tunnel, use the source-ip command in group configuration mode. To remove the alternate IP address, use the no form of this command.
source-ip ip-address
no source-ip
Syntax Description
ip-address
Alternate IP address (different from the physical IP address used to open the VPDN tunnel) that the router uses to identify the tunnel.
Defaults
Disabled
Command Modes
VPDN group configuration
Command History
Usage Guidelines
Each VPDN group on a router can be configured with a unique source-ip command.
Examples
The following example configures a LAC to accept L2TP dialout calls using the alternate IP address 172.23.33.7, which is different from the physical IP address used to open the L2TP tunnel:
vpdn-group 3accept-dialoutprotocol l2tpdialer 2terminate-from hostname orpheussource-ip 172.23.33.7Related Commands
source template
To attach a configured customer profile template to a particular customer profile, use the source template command in customer profile configuration mode.
source template name
Syntax Description
Defaults
No templates are sourced or attached to a customer profile.
Command Modes
Customer profile configuration
Command History
Usage Guidelines
All PPP and peer-default commands are allowed for a particular customer profile template under this grouping.
Examples
The following example shows the creation and configuration of a customer profile template named acme-direct and its subsequent assignment to the customer profile acme1:
template acme-directmultilink {max-fragments num | max-links num | min-links num}peer match aaa-poolspeer default ip address pool acme-numbersppp ipcp dns 10.1.1.1 10.2.2.2ppp multilinkexitresource-pool profile customer acme1source template acme-directRelated Commands
Accesses the template configuration mode for configuring a particular customer profile template.
source vpdn-template
To configure an individual virtual private dialup network (VPDN) group to use VPDN template settings for all unspecified parameters, use the source vpdn-template command in VPDN group configuration mode. To configure an individual VPDN group to use system default settings rather than the VPDN template settings for all unspecified parameters, use the no form of this command.
source vpdn-template [name]
no source vpdn-template [name]
Syntax Description
Defaults
VPDN template settings are applied to individual VPDN groups.
Command Modes
VPDN group configuration
Command History
Usage Guidelines
Use this command to couple or uncouple individual VPDN groups from the VPDN template.
The default hierarchy for the application of VPDN parameters to a VPDN group is as follows:
•
•
•
Uncoupling an individual VPDN group from the VPDN template using the no source vpdn-template command results in the following hierarchy for the application of VPDN parameters to that individual VPDN group:
•
•
Use the optional name attribute to associate and name a VPDN template with a VPDN group. You can associate a VPDN group with one VPDN template at a time.
Examples
The following example shows how to configure VPDN group 1 to ignore the VPDN template settings and use the system default settings for all unspecified VPDN parameters:
vpdn-group 1no source vpdn-templateRelated Commands
spe
To enter service processing element (SPE) configuration mode and set the range of SPEs, use the spe command in global configuration mode.
Cisco AS5350 and Cisco AS5400 with the NextPort Dial Feature Card (DFC)
spe {slot | slot/spe}
Cisco AS5800 with the Universal Port Card (UPC)
spe {shelf/slot | shelf/slot/spe}
Syntax Description
Defaults
No default behavior or values.
Command Modes
Global configuration
Command History
Usage Guidelines
The spe global configuration command enables the SPE configuration mode. Configure your SPE by specifying a slot and an SPE associated with the slot; or, you can configure a range of SPEs by specifying the first and last SPE in the range.
To exit SPE configuration mode, use the exit command.
Examples
The following example shows the spe command being used from global configuration mode to access the SPE configuration mode for the SPE range from 1/2 to 1/4:
router(config)# spe 5/4 5/6router(config-spe)# ?SPE Configuration Commands:busyout Busyout SPEdefault Set a command to its defaultsexit Exit from SPE Configuration Modefirmware Firmware used for the SPEhelp Description of the interactive help systemno Negate a command or set its defaultsshutdown Take the SPE out of ServiceWhen the universal gateway is booted, the spe global configuration command specifies the location from where the firmware image is downloaded to the SPE. If the spe configuration command is used to download the firmware from Flash memory and then subsequently the no version of the exact command is entered, then the spe command downloads the embedded firmware.
Note
Caution
The following example shows the spe command being used from global configuration mode to access the SPE configuration mode for the range of SPEs from 1/2 to 1/4 on the Cisco AS5400:
Router(config)# spe 1/2 1/4The following example specifies the range for use of the shutdown command:
Router(config)# spe 1/1 1/18Router(config-spe)# shutdownRouter(config-spe)# no shutdownRelated Commands
spe call-record modem
To generate a modem call record at the end of each call, use the spe call-record modem command in global configuration mode. To cancel the request to generate the reports, use the no form of the command.
spe call-record modem {max-userid number | quiet\
no spe call-record modem {max-userid number | quiet}
Syntax Description
max-userid number
Maximum length of the user ID for the modem call record report in number of bytes. The range is from 0 to 100.
quiet
Disables logging to console and terminal, but not to syslog.
Defaults
An SPE call record is enabled.
Command Modes
Global configuration
Command History
Usage Guidelines
The spe modem-call-record command generates a modem call record at the end of each call.
Note
Examples
The following example displays an SPE call record:
Router# configure terminalRouter(config)# spe call-record modem max-userid 50Router(config)# endRouter#00:18:30: %SYS-5-CONFIG_I: Configured from console by consoleRouter# write memoryBuilding configuration...[OK]The following is a partial example of traces generated when a call terminates. The logs from the show port modem log command do not change as a result of using the spe call-record modem command.
...%LINK-3-UPDOWN: Interface Async5/105, changed state to down%MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/2/15,shelf/slot/port=5/37, call_id=EE, userid=touraco-e1-4, ip=79.188.24.1,calling=(n/a), called=35160, std=V.34+, prot=LAP-M, comp=V.42bis,init-rx/tx b-rate=33600/33600, finl-rx/tx b-rate=33600/33600, rbs=0,d-pad=None, retr=1, sq=5, snr=10495, rx/tx chars=286/266, bad=0, rx/txec=16/6, bad=0, time=96, finl-state=Steady Retrain,disc(radius)=(n/a)/(n/a), disc(modem)=1F00 <unknown>/Requested byhost/non-specific host disconnect%MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/1/24,shelf/slot/port=5/38, call_id=FD, userid=touraco-e1-4, ip=79.205.24.1,calling=(n/a), called=35170, std=V.34+, prot=LAP-M, comp=V.42bis,init-rx/tx b-rate=33600/33600, finl-rx/tx b-rate=33600/33600, rbs=0,d-pad=None, retr=1, sq=5, snr=10495, rx/tx chars=289/267, bad=0, rx/txec=17/7, bad=0, time=93, finl-state=Steady Retrain,disc(radius)=(n/a)/(n/a), disc(modem)=1F00 <unknown>/Requested byhost/non-specific host disconnect%MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/3/15,shelf/slot/port=5/2, call_id=FF, userid=touraco-e1-4, ip=79.200.24.1,calling=(n/a), called=35170, std=V.34+, prot=LAP-M, comp=V.42bis,init-rx/tx b-rate=33600/33600, finl-rx/tx b-rate=33600/33600, rbs=0,d-pad=None, retr=1, sq=5, snr=10495, rx/tx chars=287/270, bad=0, rx/txec=17/7, bad=0, time=92, finl-state=Steady Retrain,disc(radius)=(n/a)/(n/a), disc(modem)=1F00 <unknown>/Requested byhost/non-specific host disconnect%MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/3/10,shelf/slot/port=5...Related Commands
modem call-record
Activates the logging of a summary of modem events upon the termination of a call.
spe country
To specify the country while setting the modem card parameters (including country code and encoding), use the spe country command in global configuration mode. To set the country code to the default value, use the no form of this command.
spe country {country-name | e1-default | t1-default}
no spe country {country-name | e1-default | t1-default}
Syntax Description
country-name
Name of the country, See Table 136 for a list of supported country name keywords.
e1-default
Use this command when using the E1 interface.
t1-default
Use this command when using the T1 interface.
Defaults
Disabled
Command Modes
Global configuration
Command History
Usage Guidelines
On the Cisco universal gateway, DS0 companding law selection is configured for the entire system rather than on individual voice ports. Set the spe country command to the appropriate country.
If T1 lines are configured, the default is t1-default; if E1 lines are configured, the default is e1-default.
The Cisco universal gateway must be in an Idle state (no calls are active) for the spe country command to function. All sessions on all modules in all slots must be in the Idle state.
Note
Table 136 lists the country names and corresponding commanding law.
Examples
The following example configures the setting of the country code to the default for E1:
router(config)# spe country e1-defaultThe following example configures the setting of the country code to the default for T1:
router(config)# spe country t1-defaultRelated Commands
spe download maintenance
To perform download maintenance on service processing elements (SPEs) that are marked for recovery, use the spe download maintenance command in global configuration mode. To disable download maintenance on SPEs, use the no form of the command.
spe download maintenance {time hh:mm | stop-time hh:mm | max-spes number-of-spes | window time-period | expired-window {drop-call | reschedule}}
no spe download maintenance {time hh:mm | stop-time hh:mm | max-spes number-of-spes | window time-period | expired-window {drop-call | reschedule}}
Syntax Description
Defaults
Enabled
Command Modes
Global configuration
Command History
Usage Guidelines
The SPE download maintenance activity takes place when SPEs are marked for recovery. The settings are enabled by default. When you want to change the default settings to a desired setting, use the spe download maintenance command parameters to perform SPE download maintenance activity with the specific changes.
Enter the time hh:mm keyword to set a time to start the SPE download maintenance activity. Then enter the stop-time hh:mm keyword to set a time to stop the download maintenance. Next enter the max-spes number-of-spes keyword to set the number of SPEs for the download maintenance. Then enter the window time-period keyword to set a time period to perform the download maintenance. Finally, enter the expired-window keyword to set actions in the event the SPE download maintenance is not completed in the set window time-period.
The download maintenance activity starts at the set start time and steps through all the SPEs that need recovery and the SPEs that need a firmware upgrade and starts maintenance on the maximum number of set SPEs for maintenance. The system waits for the window delay time for all the ports on the SPE to become inactive before moving the SPE to the Idle state. Immediately after the SPE moves to the Idle state, the system starts to download firmware. If the ports are still in use by the end of window delay time, depending upon the expired-window setting, connections on the SPE ports are shut down and the firmware is downloaded by choosing the drop-call option, or the firmware download is rescheduled to the next download maintenance time by choosing the reschedule option. This process continues until the number of SPEs under maintenance is below the max-spes value, or until the stop-time value (if set), or until all SPEs marked for recovery or upgrade have had their firmware reloaded.
Examples
The following example displays the SPE download maintenance with the different keyword parameters:
Router(config)# spe download maintenance time 03:00Router(config)# spe download maintenance stop-time 04:00Router(config)# spe download maintenance max-spes 50Router(config)# spe download maintenance window 30Router(config)# spe download maintenance expired-window rescheduleRelated Commands
spe log-size
To set the buffer size for the port event log, use the spe log-size command in global configuration mode.
spe log-size number
Syntax Description
number
Defines the number of recorded events. Valid values for the number argument range from 0 to 100.
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
Examples
The following example sets the buffer size for the event log to 50:
router(config)# spe log-size 50Related Commands
show port digital log
Displays the digital data event log with the oldest event first.
show port modem log
Displays the modem port history event log or modem test log.
spe recovery
To set a service processing element (SPE) port for recovery, use the spe recovery command in global configuration mode. To disable SPE recovery or to restore the default port-threshold value, use the no form of this command.
spe recovery {port-action {disable | recover} | port-threshold number-failures}
no spe recovery {port-action | port-threshold}
Syntax Description
Defaults
There is no default port-action value. SPE recovery is disabled.
The default port-threshold value is 30 failed attempts.Command Modes
Global configuration
Command History
Usage Guidelines
Failure of an SPE port to connect after repeated tries indicates that a problem exists in the SPE or firmware. An SPE port in this state is recovered by downloading firmware.
When an SPE port fails to connect consecutively for a number of times, as specified by the port-threshold number-failures keyword and argument, the SPE is moved to a state based on the port-action configuration.
If the spe recovery port-action recover command has been configured, when the port-threshold number-failures value is exceeded, the port is temporarily marked as disabled ("d" state) to avoid further incoming calls, and it is then marked for recovery ("r" state). Any SPE that has a port marked for recovery will download firmware when the SPE is idle (when none of the ports on the SPE have active calls).
If the spe recovery port-action disable command has been configured, when the port-threshold number-failures value is exceeded, the port is marked as bad ("BAD" state). An SPE with a port that is marked as bad must be explicitly cleared in order for that port to be used again.
If no port-action is configured, the port will be marked as not in use ("_" state). An SPE with a port marked as not in use will remain unusable until it is explicitly cleared, and the SPE will not accept incoming calls on any of the ports.
SPE recovery can be disabled by issuing the no spe recovery port-action command. If SPE recovery is disabled, the SPE will behave as if no port-action has been configured.
Note
Examples
The following example configures the SPE to recover ports that exceed the call failure threshold:
Router(config)# spe recovery port-action recoverThe following example sets a value of 50 for the number of consecutive failed attempts on the port before the port-action keyword is applied:
Router(config)# spe recovery port-threshold 50Related Commands
start-character
To set the flow control start character, use the start-character command in line configuration mode. To remove the character, use the no form of this command.
start-character ascii-number
no start-character
Syntax Description
Defaults
Decimal 17
Command Modes
Line configuration
Command History
Usage Guidelines
This command defines the character that signals the start of data transmission when software flow control is in effect. Refer to the "ASCII Character Set" appendix in the Cisco IOS Configuration Fundamentals Command Reference for a list of ASCII characters.
Examples
The following example changes the start character to Ctrl-B, which is decimal 2:
line 2start-character 2Related Commands
start-chat
To specify that a chat script start on a specified line at any point, use the start-chat command in privileged EXEC mode. To stop the chat script, use the no form of this command.
start-chat regexp [line-number [dialer-string]]
no start-chat
Syntax Description
Command Modes
Privileged EXEC
Command History
Usage Guidelines
This command provides modem dialing commands for a chat script that you want to apply immediately to a line. If you do not specify a line, the script runs on the current line. If the specified line is already in use, the script is not activated and an error message appears.
The argument regexp is used to specify the name of the modem script that is to be executed. The first script that matches the argument in this command and the dialer map command will be used. For more information about regular expressions, refer to the "Regular Expressions" appendix in this publication.
This command functions only on physical terminal (TTY) lines. It does not function on virtual terminal lines.
Examples
The following example forces a dialout on line 8 using the script telebit:
start-chat telebit line 8Related Commands
stop-character
To set the flow control stop character, use the stop-character command in line configuration mode. To remove the character, use the no form of this command.
stop-character ascii-number
no stop-character
Syntax Description
Defaults
Decimal 19
Command Modes
Line configuration
Command History
Usage Guidelines
This command defines the character that signals the end of data transmission when software flow control is in effect. Refer to the "ASCII Character Set" appendix in the Cisco IOS Configuration Fundamentals Command Reference for a list of ASCII characters.
Examples
The following example changes the stop character to Ctrl-E, which is decimal 5:
line 3stop-character 5Related Commands
Sets the method of data flow control between the terminal or other serial device and the router.
Sets the flow control start character.
Sets the flow control stop character.
subscriber access
To enable Subscriber Service Switch to preauthorize the NAS-Port-ID (network access server port identifier) string before authorizing the domain name, use the subscriber access command in global configuration mode. To disable Subscriber Service Switch preauthorization, use the no form of this command.
subscriber access {pppoe | pppoa} pre-authorize nas-port-id [aaa-method-list]
no subscriber access {pppoe | pppoa} pre-authorize nas-port-id [aaa-method-list]
Syntax Description
Defaults
Authorization is disabled.
Command Modes
Global configuration
Command History
Usage Guidelines
The NAS-Port-ID string is used to locate the first service record, which may contain one of three attributes, as follows:
1.
This filtered service key then locates the final service. See the vpdn authorize domain command and the example of the domain preauthorization RADIUS user profile showing use of the vpdn:domain-list= RADIUS attribute for more details.
2.
3.
Once NAS port authorization takes place, normal authorization, which is usually the domain authorization, continues.
Note
This command enables LLID and Subscriber Service Switch querying only for PPP over Ethernet over ATM (PPPoEoATM) and PPP over Ethernet over VLAN (PPPoEoVLAN or Dot1Q) calls; all other calls, such as ISDN, are not supported.
Examples
The following example signals Subscriber Service Switch to preauthorize the NAS-Port-ID string before authorizing the domain name. This policy applies only to sessions with a PPPoE access type.
aaa new-modelaaa group server radius sg_llidserver 172.20.164.106 auth-port 1645 acct-port 1646aaa group server radius sg_waterserver 172.20.164.106 auth-port 1645 acct-port 1646aaa authentication ppp default group radiusaaa authorization confg-commandsaaa authorization network default group sg_wateraaa authorization network mlist_llid group sg_llidaaa session-id common!username s7200_2 password 0 labusername s5300 password 0 labusername sg_water password 0 labvpdn enable!vpdn-group 2request-dialinprotocol 12tpdomain water.cominitiate-to ip 30.1.1.1local name s7200_2!vpdn-group 3accept dialinprotocol pppoevirtual-template 1!! Signals Subscriber Service Switch to preauthorize the NAS-Port-ID string before! authorizing the domain name.subscriber access pppoe pre-authorize nas-port-id mlist_llid!interface Loopback0ip address 10.1.1.2 255.255.255.0!interface Loopback1ip address 10.1.1.6 255.255.255.0!interface Ethernet1/0ip address 10.1.1.8 255.255.255.0 secondaryip address 10.0.58.111 255.255.255.0no cdp enable!interface ATM4/0no ip addressno atm ilmi-keepalive!interface ATM4/0.1 point-to-pointpvc 1/100encapsulation aa15snapprotocol pppoe!interface virtual-template1no ip unnumbered Loopback0no peer default ip addressppp authentication chap!radius-server host 172.20.164.120 auth-port 1645 acct-port 1646 key rad123radius-server host 172.20.164.106 auth-port 1645 acct-port 1646 key rad123ip radius source-interface Loopback1Related Commands
subscriber authorization enable
To enable Subscriber Service Switch type authorization, use the subscriber authorization enable command in global configuration mode. To disable the Subscriber Service Switch authorization, use the no form of this command.
subscriber authorization enable
no subscriber authorization enable
Syntax Description
This command has no arguments or keywords.
Defaults
Authorization is disabled.
Command Modes
Global configuration
Command History
Usage Guidelines
The subscriber authorization enable command triggers Subscriber Service Switch type authorization for local termination, even if virtual private dialup network (VPDN) and Stack Group Bidding Protocol (SGBP) are disabled.
Examples
The following example enables Subscriber Service Switch type authorization:
subscriber authorization enableRelated Commands
Enables Subscriber Service Switch preauthorization.
Enables domain preauthorization on a NAS.
syscon address
To specify the system controller for a managed shelf, use the syscon address command in global configuration mode. To stop the management of the shelf by the system controller, use the no form of this command.
syscon address ip-address password
no syscon address
Syntax Description
Command Default
No system controller is specified.
Command Modes
Global configuration
Command History
Usage Guidelines
This command is required in order for the shelf to be managed by the system controller.
Examples
The following example configures a shelf to be managed by a system controller at 10.2.3.4 using the password green:
Router# syscon address 10.2.3.4 greenRelated Commands
show syscon sdp
Displays information about the Shelf Discovery Protocol.
syscon source-interface
Specifies the interface to use for the source address in SDP packets.
syscon shelf-id
To specify a shelf ID for a managed shelf, use the syscon shelf-id command in global configuration mode. To remove the shelf ID, use the no form of this command.
syscon shelf-id number
no syscon shelf-id
Syntax Description
Command Default
No shelf ID is specified.
Command Modes
Global configuration
Command History
Usage Guidelines
Use this command to specify a shelf ID for a managed shelf. Some platforms, such as the Cisco AS5800, use other commands to assign a shelf ID. In these situations, do not specify a shelf ID with the syscon shelf-id command. Use the platform-specific command instead.
Examples
The following example configures a shelf ID of 5 for the managed shelf:
Router# syscon shelf-id 5Related Commands
show syscon sdp
Displays information about the Shelf Discovery Protocol.
syscon address
Specifies the system controller for a managed shelf.
syscon source-interface
To specify the interface to use for the source address in Shelf Discovery Protocol (SDP) packets, use the syscon source-interface command in global configuration mode. To return to the default source interface for a packet (the interface that sent the packet from the shelf), use the no form of this command.
syscon source-interface type number
no syscon source-interface
Syntax Description
Command Default
SDP packets use the IP address of the output interface.
Command Modes
Global configuration
Command History
Usage Guidelines
Use this command to ensure that all SDP packets sent by the managed shelf have the same source IP address.
Examples
The following example configures a shelf to use the IP address of Ethernet interface 99/1/0:
Router# syscon source-address Ethernet99/1/0Related Commands
show syscon sdp
Displays information about the Shelf Discovery Protocol.
syscon shelf-id
Specifies a shelf ID for a managed shelf.
tdm clock priority
To configure the clock source and priority of the clock source used by the time-division multiplexing (TDM) bus on the Cisco AS5350, AS5400, and AS5850 access servers, use the tdm clock priority command in global configuration mode. To return the clock source and priority to the default values, use the no form of this command.
tdm clock priority priority-number {slot/ds1-port | slot/ds3-port:ds1-port | external | freerun}
no tdm clock priority priority-number {slot/ds1-port | slot/ds3-port:ds1-port | external | freerun}
Syntax Description
Defaults
If no clocks are configured, the system uses a default, primary clock. An external clock is never selected by default; it must be explicitly configured.
Command Modes
Global configuration
Command History
Usage Guidelines
The TDM bus can receive an input clock from one of three sources on the gateway:
•
•
•
Note
Trunk-Card Ports
The TDM bus can be synchronized with any trunk cards. On the CT1/CE1 trunk card, each port receives the clock from the T1/E1 line. The CT3 trunk card uses an M13 multiplexer to receive the DS1 clock. Each port on each trunk-card slot has a default clock priority. Also, clock priority is configurable through the tdm clock priority command.
External Clock
The TDM bus can be synchronized with an external clock source that can be used as an additional network reference. If no clocks are configured, the system uses a primary clock through a software-controlled default algorithm. If you want the external T1/E1 clock (from the BITS interface) as the primary clock source, you must configure it using the external keyword with the tdm clock priority command; the external clock is never selected by default.
The BITS interface requires a T1 line composite clock reference set at 1.544 MHz and an E1 line composite clock reference set at 2.048 MHz.
Free-Running Clock
If there is no good clocking source from a trunk card or an external clock source, then select the free-running clock from the internal oscillator using the freerun keyword with the tdm clock priority command.
Examples
In the following example, BITS clock is set at priority 1:
AS5400(config)# tdm clock priority priority 1 externalIn the following example, a trunk clock from a CT1 trunk card is set at priority 2 and uses slot 4 and DS1 port (controller) 6:
AS5400(config)# tdm clock priority priority 2 4/6In the following example, a trunk clock from a CT3 trunk card is set at priority 2 and uses slot 1, DS3 port 0, and DS1 port 19:
AS5400(config)# tdm clock priority priority 2 1/0:19In the following example, free-running clock is set at priority 3:
AS5400(config)# tdm clock priority priority 3 freerunRelated Commands
template
To access the template configuration mode for configuring a particular customer profile template, use the template command in global configuration mode. To delete the template of the specified name, use the no form of this command.
template name [default | exit | multilink | no | peer | ppp]
no template name [default | exit | multilink | no | peer | ppp]
Syntax Description
Defaults
No templates are configured.
Command Modes
Global configuration
Command History
Usage Guidelines
All PPP and peer-default commands are enabled for a customer profile template under this grouping.
Examples
The following example shows the creation and configuration of a customer profile template named acme-direct and its subsequent assignment to the customer profile acme1:
template acme-directmultilink max-fragments 10peer match aaa-poolspeer default ip address pool acme-numbersppp ipcp dns 10.1.1.1 10.2.2.2ppp multilinkexitresource-pool profile customer acme1source template acme-directRelated Commands
terminate-from
To specify the host name of the remote L2TP access concentrator (LAC) or L2TP network server (LNS) that will be required when accepting a virtual private dialup network (VPDN) tunnel, use the terminate-from command in VPDN group configuration mode. To remove the host name from the VPDN group, use the no form of this command.
terminate-from hostname host-name
no terminate-from [hostname host-name]
Syntax Description
Defaults
Disabled
Command Modes
VPDN group configuration
Command History
Usage Guidelines
Before you can use this command, you must have already enabled one of the two accept VPDN subgroups by using either the accept-dialin or accept-dialout command.
Each VPDN group can only terminate from a single host name. If you enter a second terminate-from command on a VPDN group, it will replace the first terminate-from command.
Examples
The following example configures a VPDN group to accept L2TP tunnels for dialout calls from the LNS cerise by using dialer 2 as its dialing resource:
vpdn-group 1accept-dialoutprotocol l2tpdialer 2terminate-from hostname ceriseRelated Commands
test modem back-to-back
To diagnose an integrated modem that may not be functioning properly, use the test modem back-to-back command in EXEC mode.
test modem back-to-back first-slot/port second-slot/port
Syntax Description
first-slot/port
Slot and modem number of the first test modem. You must include the slash mark
second-slot/port
Slot and modem number of the second test modem. You must include the slash mark
Command Modes
EXEC
Command History
Usage Guidelines
Use this command to perform back-to-back testing of two modems. You might need to enable this command on several different combinations of modems to determine which one is not functioning properly.
Examples
The following example performs a back-to-back modem test between modem 2/0 and modem 2/1 and removes modem 2/1 (which is associated with TTY line 26) from all dial-in and dial-out services:
Router# test modem back-to-back 2/0 2/1back2back 2/0 2/1Repetitions (of 10-byte packets) [1]:Router#%MODEM-5-B2BCONNECT: Modems (2/0) and (2/1) connected in back-to-back test: CONNECT9600/REL-MNPM%MODEM-5-B2BMODEMS: Modems (2/0) and (2/1) completed back-to-back test: success/packets = 2/2Related Commands
test port modem back-to-back
To test two specified ports back-to-back and transfer a specified amount of data between the ports, use the test port modem back-to-back command in EXEC mode.
Cisco AS5350 and Cisco AS5400 with the NextPort Dial Feature Card (DFC)
test port modem back-to-back {slot/port}
Cisco AS5800 with the Universal Port Card (UPC)
test port modem back-to-back {shelf/slot/port}
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
The test port modem back-to-back command should be performed on different combinations to determine a good port.
Note
Examples
The following example displays a back-to-back test:
Router# test port modem back-to-back 1/1/1Repetitions (of 10-byte packets) [1]:*Mar 02 12:13:51.743:%PM_MODEM_MAINT-5-B2BCONNECT:Modems (2/10) and (3/20) connected in back-to-back test:CONNECT33600/V34/LAP*Mar 02 12:13:52.783:%PM_MODEM_MAINT-5-B2BMODEMS:Modems (3/20) and (2/10) completed back-to-back test:success/packets = 2/2Related Commands
timeout absolute
To specify a timeout period that controls how long a session can be connected before it is terminated, use the timeout absolute command in interface configuration mode. To remove the session timeout period, use the no form of this command.
timeout absolute minutes [seconds]
no timeout absolute
Syntax Description
minutes
Session lifetime in minutes, in the range from 0 to 71582787 minutes.
seconds
(Optional) Session lifetime in seconds, in the range from 0 to 59 seconds.
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
Examples
The following partial example shows how to impose a 15-minute (900-second) idle timeout and a 12-hour (720-minute) absolute timeout for session connections:
interface Serial0:23dialer idle-timeout 900timeout absolute 720!interface Serial1:23dialer idle-timeout 900timeout absolute 720...Related Commands
ppp idle timeout
Sets PPP idle timeout parameters.
dialer idle-timeout
Specifies the idle time before the line is disconnected.
timer
To set the Redundant Link Manager (RLM) timer, use the timer command in RLM configuration mode. The associated options can overwrite the default setting of timeout values. To disable this function, use the no form of this command.
timer {force-down | keepalive | minimum-up | open-wait | recovery | retransmit | switch-link} seconds
no timer {force-down | keepalive | minimum-up | open-wait | recovery | retransmit | switch-link} seconds
Syntax Description
Defaults
Disabled
Command Modes
RLM configuration
Command History
Related Commands
trunk group (global)
To define a trunk group, use the trunk group command in global configuration mode. To disable the specified trunk group, use the no form of this command.
trunk group group-number [max-calls {any | voice | data] number] | [direction in | out] [max-retries retries]
no trunk group group-number
Syntax Description
Defaults
No trunk group is defined.
If the max-calls any keyword is not specified, the trunk group allows all calls, both incoming and outgoing.
The default maximum number of retries is 1.
Command Modes
Global configuration
Command History
Usage Guidelines
Use this command to define the trunk group. Then if you decide to configure an interface for the Network Side ISDN PRI feature, use a trunk-group interface configuration command to assign the interface to a defined trunk group.
However, a trunk group need not be defined globally before being configured on an interface. If it has not been defined, it will be created.
The max-calls keyword set can be repeated to allow you to specify the maximum number of voice calls, the maximum number of data calls, and the maximum number of any calls.
Examples
The following example defines trunk group 101 but does not specify a maximum number of calls:
trunk group 101The following example specifies multiple maximums. In the first version of the example, the maximums are shown on separate lines for readability, but in reality they are part of a single command:
trunk group 101max-calls any 100max-calls voice 30max-calls data 60 direction inIn the second version of the example, the same command is shown in a single run-on line:
trunk group 101 max-calls any 100 max-calls voice 30 max-calls data 60 direction inRelated Commands
tunnel
To set up a network layer connection to a router, use the tunnel command in EXEC mode.
tunnel host
Syntax Description
Command Modes
EXEC
Command History
Usage Guidelines
If you are a mobile user, it is often impractical to dial in to your "home" router from a remote site. The asynchronous mobility feature allows you to dial in to different routers elsewhere on the internetwork while experiencing the same server environment that you would if you were connecting directly to your home router.
This asynchronous host mobility is accomplished by packet tunneling, a technique by which raw data from the dial-in user is encapsulated and transported directly to the host site where your home router performs the actual protocol processing.
You enable asynchronous mobility by entering the tunnel command to set up a network layer connection to a specified host. From a router other than a Cisco router, however, you need to use the Telnet protocol.
After a connection is established, you receive an authentication dialog or prompt from your home router and can proceed as if you are connected directly to it. When communications are complete, the network connection can be closed and terminated from either end of the connection.
Examples
The following example establishes a network layer connection with an IBM host named mktg:
Router> tunnel mktgvirtual-profile aaa
To enable virtual profiles by authentication, authorization, and accounting (AAA) configuration, use the virtual-profile aaa command in global configuration mode. To disable virtual profiles, use the no form of this command.
virtual-profile aaa
no virtual-profile aaa
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled
Command Modes
Global configuration
Command History
Usage Guidelines
The effect of this command for any specific user depends on the router being configured for AAA and the AAA server being configured for that user's specific configuration information.
Examples
The following example configures virtual profiles by AAA configuration only:
virtual-profile aaaRelated Commands
aaa authentication
Enables AAA authentication to determine if a user can access the privileged command level.
Enables virtual profiles by virtual interface template.
virtual-profile if-needed
To specify that a virtual profile be used to create a virtual access interface only if the inbound connection requires a virtual access interface, use the virtual-profile if-needed command in global configuration mode. To create virtual access interfaces for every inbound connection, use the no form of this command.
virtual-profile if-needed
no virtual-profile if-needed
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled
Command Modes
Global configuration
Command History
Usage Guidelines
This command is intended to prevent the creating of virtual-access interfaces for inbound calls on physical interfaces that do not require virtual-access interfaces.
This command is compatible with local, RADIUS, and TACACS+ AAA.
Examples
The following example enables selective virtual-access interface creation:
virtual-profile if-neededRelated Commands
virtual-profile virtual-template
To enable virtual profiles by virtual interface template, use the virtual-profile virtual-template command in global configuration mode. To disable this function, use the no form of this command.
virtual-profile virtual-template number
no virtual-profile virtual-template number
Syntax Description
Defaults
Disabled. No virtual template is defined, and no default virtual template number is used.
Command Modes
Global configuration
Command History
Usage Guidelines
When virtual profiles are configured by virtual templates only, any interface-specific configuration information that is downloaded from the AAA server is ignored in configuring the virtual access interface for a user.
The interface virtual-template command defines a virtual template to be used for virtual profiles. Because several virtual templates might be defined for different purposes on the router (such as MLP, PPP over ATM, and virtual profiles), it is important to be clear about the virtual template number to use in each case.
Examples
The following example configures virtual profiles by virtual templates only. The number 2 was chosen because virtual template 1 was previously defined for use by Multilink PPP.
virtual-profile virtual-template 2Related Commands
Creates a virtual template interface that can be configured and applied dynamically in creating virtual access interfaces.
virtual-template
To specify which virtual template will be used to clone virtual access interfaces, use the virtual-template command in VPDN group configuration mode. To remove the virtual template from a virtual private dial-up network (VPDN) group, use the no form of this command.
virtual-template template-number
no virtual-template
Syntax Description
template-number
Number of the virtual template that will be used to clone virtual access interfaces.
Defaults
No virtual template is enabled.
Command Modes
VPDN group configuration
Command History
Usage Guidelines
You must first enable a tunneling protocol on the VPDN group using the protocol (VPDN) command before you can enable the virtual-template command. Removing or modifying the protocol command will remove the virtual-template command from the VPDN group.
Each VPDN group can clone only virtual access interfaces using one virtual template. If you enter a second virtual-template command on a VPDN group, it will replace the first virtual-template command.
Table 137 lists the VPDN group commands under which the virtual-template command can be entered. Entering the VPDN group command starts VPDN group configuration mode. The table includes the command-line prompt for the VPDN group configuration mode and the type of service configured.
When the virtual-template command is entered under a request-dialout VPDN subgroup, IP and other per-user attributes can be applied to an L2TP dial-out session from an LNS. Before this command was enhanced, IP per-user configurations from authentication, authorization, and accounting (AAA) servers were not supported; the IP configuration would come from the dialer interface defined on the router.
The enhanced virtual-template command works in a way similar to configuring virtual profiles and L2TP dial-in. The L2TP virtual access interface is first cloned from the virtual template, which means that configurations from the virtual template interface will be applied to the L2TP virtual access interface. After authentication, the AAA per-user configuration is applied to the virtual access interface. Because AAA per-user attributes are applied only after the user has been authenticated, the LNS must be configured to authenticate the dial-out user (configuration authentication is needed for this command).
With the enhanced virtual-template command, all software components can now use the configuration present on the virtual access interface rather than what is present on the dialer interface. For example, IP Control Protocol (IPCP) address negotiation uses the local address of the virtual access interface as the router address while negotiating with the peer.
Examples
The following example enables the LNS to accept an L2TP tunnel from an L2TP access concentrator (LAC) named LAC2. A virtual access interface will be cloned from virtual template 1.
vpdn-group 1accept-dialinprotocol l2tpvirtual-template 1terminate-from hostname LAC2The following example enables PPPoE on ATM to accept dial-in PPPoE sessions. A virtual access interface for the PPP session is cloned from virtual template 1.
vpdn-group 1accept-dialinprotocol pppoevirtual-template 1The following partial example shows how to configure an LNS to support IP per-user configurations from a AAA server:
!vpdn enablevpdn search-order domain!vpdn-group 1...request-dialoutprotocol l2tprotary-group 1virtual-template 1initiate-to ip 10.0.1.194.2local name lnsl2tp tunnel password 7094F3$!5^3source-ip 10.0.194.53!The previous configuration requires a AAA profile such as the following example to specify the per-user attributes:
5300-Router1-out Password = "cisco"Service-Type = Outboundcisco-avpair = "outbound:dial-number=5553021"7200-Router1-1 Password = "cisco"Service-Type = Outboundcisco-avpair = "ip:route=10.17.17.1 255.255.255.255 Dialer1 100 name 5300-Router1"5300-Router1 Password = "cisco"Service-Type = FramedFramed-Protocol = PPPcisco-avpair = "lcp:interface-config=ip unnumbered loopback 0"cisco-avpair = "ip:outacl#1=deny ip host 10.5.5.5 any log"cisco-avpair = "ip:outacl#2=permit ip any any"cisco-avpair = "ip:inacl#1=deny ip host 10.5.5.5 any log"cisco-avpair = "ip:inacl#2=permit ip any any"cisco-avpair = "multilink:min-links=2"Framed-Route = "10.5.5.6/32 Ethernet4/0"Framed-Route = "10.5.5.5/32 Ethernet4/0"Idle-Timeout = 100Related Commands
vpdn aaa attribute
To enable reporting of network access server (NAS) authentication, authorization, and accounting (AAA) attributes related to a virtual private dialup network (VPDN) to the AAA server, use the vpdn aaa attribute command in global configuration mode. To disable reporting of AAA attributes related to VPDN, use the no form of this command.
vpdn aaa attribute {nas-ip-address vpdn-nas | nas-port {vpdn-nas | physical-channel-id}}
no vpdn aaa attribute {nas-ip-address vpdn-nas | nas-port}
Syntax Description
Command Default
AAA attributes are not reported to the AAA server.
Command Modes
Global configuration
Command History
Usage Guidelines
This command can be used with RADIUS or TACACS+, and is applicable only on the VPDN tunnel server.
The PPP extended NAS-Port format enables the NAS-Port and NAS-Port-Type attributes to provide port details to a RADIUS server when one of the following protocols is configured:
•
•
•
Before PPP extended NAS-Port format attributes can be reported to the RADIUS server, the radius-server attribute nas-port format command with the d keyword must be configured on both the tunnel server and the NAS, and the tunnel server and the NAS must both be Cisco routers.
Examples
The following example configures VPDN on a tunnel server and enables reporting of VPDN AAA attributes to the AAA server:
vpdn enablevpdn-group 1accept-dialinprotocol anyvirtual-template 1!terminate-from hostname nas1local name ts1!vpdn aaa attribute nas-ip-address vpdn-nasvpdn aaa attribute nas-port vpdn-nasvpdn aaa attribute nas-port physical-channel-idThe following example configures the tunnel server for VPDN, enables AAA, configures a RADIUS AAA server, and enables reporting of PPP extended NAS-Port format values to the RADIUS server. PPP extended NAS-Port format must also be configured on the NAS for this configuration to be effective.
vpdn enablevpdn-group L2TP-tunnelaccept-dialinprotocol l2tpvirtual-template 1!terminate-from hostname nas1local name ts1!aaa new-modelaaa authentication ppp default local group radiusaaa authorization network default local group radiusaaa accounting network default start-stop group radius!radius-server host 171.79.79.76 auth-port 1645 acct-port 1646radius-server retransmit 3radius-server attribute nas-port format dradius-server key ts123!vpdn aaa attribute nas-port vpdn-nasRelated Commands
radius-server attribute nas-port format
Selects the NAS-Port format used for RADIUS accounting features.
vpdn aaa override-server
To specify an authentication, authorization, and accounting (AAA) server to be used for virtual private dialup network (VPDN) tunnel authorization other than the default AAA server, use the vpdn aaa override-server global configuration command. To return to the default setting, use the no form of this command.
vpdn aaa override-server {aaa-server-ip-address | aaa-server-name}
no vpdn aaa override-server {aaa-server-ip-address | aaa-server-nam}
Syntax Description
aaa-server-ip-address
The IP address of the AAA server to be used for tunnel authorization.
aaa-server-name
The name of the AAA server to be used for tunnel authorization.
Defaults
If the AAA server is not specified, the default AAA server configured for network authorization is used.
Command Modes
Global configuration
Command History
Usage Guidelines
This command can be used with RADIUS or TACACS+, and is applicable only on the VPDN network access server (NAS). Configuring this command restricts tunnel authorization to the specified AAA servers only. This command can be used to specify multiple AAA servers.
For TACACS+ configuration, the tacacs-server directed-request command must be configured using the restricted keyword, or authorization will continue with all configured TACACS+ servers.
Examples
The following example enables AAA attributes and specifies the AAA server to be used for VPDN tunnel authorization:
aaa new-modelaaa authorization network default group radiusvpdn aaa override-server 10.1.1.1vpdn enableradius-server host 10.1.1.2 auth-port 1645 acct-port 1646radius-server key SecretRelated Commands
vpdn aaa untagged
To apply untagged attribute values obtained from the authentication, authorization, and accounting (AAA) RADIUS server to all attribute sets for virtual private dialup network (VPDN) tunnels, use the vpdn aaa untagged command in global configuration mode. To disable this function, use the no form of this command.
vpdn aaa untagged
no vpdn aaa untagged
Syntax Description
This command has no arguments or keywords.
Defaults
Untagged attribute values are applied to all attribute sets.
Command Modes
Global configuration
Command History
Usage Guidelines
Untagged attribute values obtained from the AAA RADIUS server will be applied to all attribute sets by default, unless a value for that attribute is already specified in the tagged attribute set. To prevent untagged attribute values from being applied to tagged attribute sets, use the no form of this command.
Examples
The following example disables the application of untagged attribute values to attribute sets:
no vpdn aaa untaggedvpdn authen-before-forward
To configure a network access server (NAS) to request authentication of a complete username before making a forwarding decision for all dial-in Layer 2 Tunnel Protocol (L2TP) or Layer 2 Forwarding (L2F) tunnels, use the vpdn authen-before-forward command in global configuration mode. To disable this configuration, use the no form of this command.
vpdn authen-before-forward
no vpdn authen-before-forward
Syntax Description
This command has no arguments or keywords.
Command Default
L2TP or L2F tunnels are forwarded to the tunnel server without first requesting authentication of the complete username.
Command Modes
Global configuration
Command History
Usage Guidelines
To configure the NAS to perform authentication of all dial-in L2TP or L2F sessions before the sessions are forwarded to the tunnel server, configure the vpdn authen-before-forward command in global configuration mode.
To configure the NAS to perform authentication of dial-in L2TP or L2F sessions belonging to a specific VPDN group before the sessions are forwarded to the tunnel server, use the authen-before-forward command in VPDN group configuration mode.
Enabling the vpdn authen-before-forward command instructs the NAS to authenticate the complete username before making a forwarding decision based on the domain portion of the username. A user may be forwarded or terminated locally depending on the information contained in the users RADIUS profile. Users with forwarding information in their RADIUS profile are forwarded based on that information. Users without forwarding information in their RADIUS profile are either forwarded or terminated locally based on the Service-Type in their RADIUS profile. The relationship between forwarding decisions and the information contained in the users RADIUS profile is summarized in Table 138.
Examples
The following example configures the NAS to request authentication of all dial-in L2TP or L2F sessions before the sessions are forwarded to the tunnel server:
vpdn authen-before-forwardRelated Commands
vpdn authorize directed-request
To enable virtual private dialup network (VPDN) authorization for directed-request users, use the vpdn authorize directed-request command in global configuration mode. To disable VPDN authorization for directed request users, use the no form of this command.
vpdn authorize directed-request
no vpdn authorize directed-request
Syntax Description
This command has no keywords or arguments.
Defaults
VPDN authorization for directed-request users is disabled.
Command Modes
Global configuration
Command History
Usage Guidelines
When a username incudes both a username and a domain portion, such as user@site.com, directed request configuration allows the authorization request to be sent to a specific RADIUS or TACACS+ server based on the domain name portion of the username (site.com). The vpdn authorize directed-request command must be enabled to allow VPDN authorization of any directed request user.
Directed request for RADIUS users is enabled by issuing the radius-server directed-request command. Directed request for TACACS+ users is enabled by default, and may be disabled using the no tacacs-server directed request command. The ip host command must be configured to enable directed requests to RADIUS or TACACS+ servers.
The vpdn authorize directed-request command is usually configured on the L2TP network server (LNS). When directed-requests are used on an L2TP access concentrator (LAC) in conjuction with per-user VPDN configuration, the authen before-forward command must be enabled.
Examples
The following example enables VPDN authorization and RADIUS directed requests on an LNS:
ip host site.com 10.1.1.1radius-server host 10.1.1.1 auth-port 1645 acct-port 1646radius-server directed-requestvpdn authorize directed-requestThe following example enables VPDN authorization and TACACS+ directed requests on an LNS:
ip host site.com 10.1.1.1tacacs-server host 10.1.1.1tacacs-server directed-requestvpdn authorize directed-requestThe following example enables per-user VPDN and enables VPDN authorization for directed request users on a LAC:
vpdn-group 1request-dialinprotocol l2fdomain site.com!initiate-to ip 10.1.1.1local name local1authen before-forward!ip host site.com 10.1.1.1vpdn authorize directed-request!radius-server host 10.1.1.1 auth-port 1645 acct-port 1646radius-server directed-requestRelated Commandsradius-server directed-requestradius-server directed-request
vpdn authorize domain
To enable domain preauthorization on a network access server (NAS), use the vpdn authorize domain command in global configuration mode. To disable domain preauthorization, use the no form of this command.
vpdn authorize domain
no vpdn authorize domain
Syntax Description
This command has no arguments or keywords.
Defaults
Domain preauthorization is disabled by default.
Command Modes
Global configuration
Command History
12.1(1)DC1
This command was introduced on the Cisco 6400 NRP.
12.2(13)T
This command was integrated into Cisco IOS Release 12.2(13)T.
Usage Guidelines
A RADIUS domain preauthorization user profile must also be created. See the "Examples" section and refer to the Cisco IOS Security Configuration Guide, Release 12.2, for information on how to create these profiles.
Examples
Domain Preauthorization Configuration on the LAC Example
The following example shows the configuration necessary for a L2TP access concentrator (LAC) to participate in domain preauthorization:
!aaa new-modelaaa authorization network default local group radius!vpdn authorize domain!radius-server host 10.9.9.9 auth-port 1645 acct-port 1646radius-server attribute nas-port format dradius-server key MyKeyradius-server vsa send authentication!Domain Preauthorization RADIUS User Profile Example
The following example shows a domain preauthorization RADIUS user profile:
user = nas-port:10.9.9.9:0/0/0/30.33{profile_id = 826profile_cycle = 1radius=Cisco {check_items= {2=cisco}reply_attributes= {9,1="vpdn:vpn-domain-list=net1.com,net2.com"6=5}}vpdn domain-delimiter
To specify the characters to be used to delimit the domain prefix or domain suffix, use the vpdn domain-delimiter command in global configuration mode. To disable this function, use the no form of this command.
vpdn domain-delimiter characters [suffix | prefix]
no vpdn domain-delimiter characters [suffix | prefix]
Syntax Description
Defaults
Disabled
Command Modes
Global configuration
Command History
Usage Guidelines
You can enter one vpdn domain-delimiter command to list the suffix delimiters and another vpdn domain-delimiter command to list the prefix delimiters. However, no character can be both a suffix delimiter and a prefix delimiter.
This command allows the network access server to parse a list of home gateway DNS domain names and addresses sent by an AAA server. The AAA server can store domain names or IP addresses in the following AV pair:
cisco-avpair = "lcp:interface-config=ip address 10.1.1.1 255.255.255.255.0",
cisco-avpair = "lcp:interface-config=ip address bigrouter@excellentinc.com,
Examples
The following example lists three suffix delimiters and three prefix delimiters:
vpdn domain-delimiter %-@ suffixvpdn domain-delimiter #/\\ prefixThis example allows the following host and domain names:
cisco.com#houstonddrhoustonddr@cisco.comRelated Commands
vpdn enable
To enable virtual private dialup networking on the router and inform the router to look for tunnel definitions in a local database and on a remote authorization server (home gateway), if one is present, use the vpdn enable command in global configuration mode. To disable, use the no form of this command.
vpdn enable
no vpdn enable
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled
Command Modes
Global configuration
Command History
Usage Guidelines
To disable a VPN tunnel, use the command clear vpdn tunnel in EXEC mode. The command no vpdn enable does not automatically disable a VPN tunnel.
Examples
The following example enables virtual private dialup networking on the router:
vpdn enableRelated Commands
vpdn group
To associate a virtual private dialup network (VPDN) group with a customer or VPDN profile, use the vpdn group command in customer profile or VPDN profile configuration mode. To disassociate a VPDN group from a customer or VPDN profile, use the no form of this command.
vpdn group name
no vpdn group name
Syntax Description
name
Name of the VPDN group.
Note
Defaults
No default behavior or values.
Command Modes
Customer profile configuration
VPDN profile configurationCommand History
12.0(4)XI
This command was introduced.
12.0(5)T
This command was integrated into Cisco IOS Release 12.0(5)T.
Usage Guidelines
Use the vpdn group command in customer profile configuration mode or VPDN profile configuration mode to associate a VPDN group with a customer profile or a VPDN profile, respectively.
VPDN groups are created using the vpdn-group command in global configuration mode.
Examples
The following example creates the VPDN groups named l2tp and l2f, and associates both VPDN groups with the VPDN profile named profile32:
Router(config)# vpdn-group l2tpRouter(config-vpdn)#!Router(config)# vpdn-group l2fRouter(config-vpdn)#!Router(config)# resource-pool profile vpdn profile32Router(config-vpdn-profile)# vpdn group l2tpRouter(config-vpdn-profile)# vpdn group l2fThe following example creates two VPDN groups and configures them under a customer profile named company2:
Router(config)# vpdn-group mygroupRouter(config-vpdn)#!Router(config)# vpdn-group yourgroupRouter(config-vpdn)#!Router(config)# resource-pool profile vpdn company2Router(config-vpdn-profile)# vpdn group mygroupRouter(config-vpdn-profile)# vpdn group yourgroupRelated Commands
vpdn history failure
To enable logging of virtual private dialup network (VPDN) failures to the history failure table or to set the failure history table size, use the vpdn history failure command in global configuration mode. To disable logging of VPDN history failures or to restore the default table size, use the no form of this command.
vpdn history failure [table-size entries]
no vpdn history failure [table-size]
Syntax Description
table-size entries
(Optional) Sets the number of entries in the history failure table. Valid entries range from 20 to 50.
Defaults
VPDN failures are logged by default.
table size: 20 entriesCommand Modes
Global configuration
Command History
Usage Guidelines
Logging of VPDN failure events is enabled by default. You can disable the logging of VPDN failure events by issuing the no vpdn history failure command.
The logging of a failure event to the history table is triggered by event logging by the syslog facility. The syslog facility creates a failure history table entry, which keeps records of failure events. The table starts with 20 entries, and the size of the table can be expanded to a maximum of 50 entries using the vpdn history failure table-size entries command. You may configure the vpdn history failure table-size entries command only if VPDN failure event logging is enabled.
All failure entries for the user are kept chronologically in the history table. Each entry records the relevant information of a failure event. Only the most recent failure event per user, unique to its name and tunnel client ID (CLID), is kept.
When the total number of entries in the table reaches the configured table size, the oldest record is deleted and a new entry is added.
Examples
The following example disables logging of VPDN failures to the history failure table:
no vpdn history failureThe following example enables logging of VPDN failures to the history table and sets the history failure table size to 40 entries:
vpdn history failurevpdn history failure table-size 40Related Commands
vpdn incoming
The vpdn incoming command is replaced by the accept-dialin command. See the description of the accept-dialin command for more information.
vpdn ip udp ignore checksum
To allow the router to ignore UDP checksums for Layer 2 Forwarding (L2F) and Layer 2 Tunnel Protocol (L2TP) virtual private dial-up network (VPDN) traffic, use the vpdn ip udp ignore checksum command in global configuration mode. To restore the default state in which the router does not ignore UDP checksums, use the no form of this command.
vpdn ip udp ignore checksum
no vpdn ip udp ignore checksum
Syntax Description
This command has no arguments or keywords.
Defaults
UDP checksums are not ignored.
Command Modes
Global configuration
Command History
Usage Guidelines
Enable the vpdn ip udp ignore checksum command when the remote tunnel endpoint uses UDP checksums and you wish to use fast switching or Cisco Express Forwarding (CEF). If the remote tunnel endpoint uses UDP checksums and the vpdn ip udp ignore checksum command is not enabled, all tunnel traffic will be process-switched.
Examples
The following example configures the router to ignore UDP checksums, allowing fast switching or CEF:
vpdn ip udp ignore checksumvpdn logging
To enable the logging of virtual private dialup network (VPDN) events, use the vpdn logging command in global configuration mode. To disable the logging of VPDN events, use the no form of this command.
vpdn logging [accounting | local | remote | user]
no vpdn logging [accounting | local | remote | user]
Syntax Description
Defaults
All VPDN event logging is disabled.
Command Modes
Global configuration
Command History
11.3T
This command was introduced.
12.1
The user keyword was introduced in Cisco IOS Release 12.1.
12.2(15)T
The accounting keyword was introduced.
Usage Guidelines
This command controls the logging of VPDN events. By default, all VPDN event logging is disabled.
To enable the logging of VPDN events to the system message logging (syslog) of the local or remote tunnel endpoint router, issue the vpdn logging command with the local or remote keyword.
To log VPDN user events to the syslog, you must configure the vpdn logging command with the user keyword.
Configuring the vpdn logging command with the accounting keyword causes VPDN event log messages to be sent to a remote AAA server in a AAA vendor-specific attribute (VSA), allowing the correlation of VPDN call success rates with accounting records.
Note
You may configure as many types of VPDN event logging as you want.
Examples
The following example enables VPDN logging locally:
vpdn logging localThe following example disables VPDN event logging locally, enables VPDN event logging at the remote tunnel endpoint, and enables the logging of VPDN user events to the syslog of the remote router:
no vpdn logging localvpdn logging remotevpdn logging userThe following example disables the logging of VPDN events to the syslog both locally and at the remote tunnel endpoint, and enables the reporting of VPDN event log messages to the AAA server:
no vpdn logging localno vpdn logging remotevpdn logging accountingRelated Commands
vpdn history failure
Enables logging of VPDN failures to the history failure table or sets the failure history table size.
vpdn multihop
To enable virtual private dialup network (VPDN) multihop, use the vpdn multihop command in global configuration mode. To disable VPDN multihop capability, use the no form of this command.
vpdn multihop
no vpdn multihop
Syntax Description
This command has no arguments or keywords.
Defaults
Multihop capability is not enabled.
Command Modes
Global configuration
Command History
Usage Guidelines
The VPDN multihop feature allows a router configured as a tunnel switch to terminate tunnels from Layer 2 access concentrators (LACs) and forward the sessions through up to four newly established Layer 2 Tunneling Protocol (L2TP) tunnels. The tunnels are selected using client-supplied matching criteria. Versions of Cisco IOS software prior to Cisco IOS Release 12.2(8)B support L2TP tunnel switching using only a user domain name or a remote tunnel name as the matching criterion.
The dialed number identification service (DNIS)-based multihop capability added a telephone number to the matching criteria for the tunnel switch. The tunnel switch can perform VPDN tunnel authorization based on a DNIS (a called telephone number), a user domain name, or ingress tunnel domain names that are mapped to specified L2TP network servers (LNSs). The order in which the client-supplied matching criteria are searched by the Cisco IOS software is determined by the vpdn search-order global configuration command.
Before using the vpdn multihop command, refer to the Cisco IOS Dial Technologies Configuration Guide, Release 12.2, to learn more about Multilink PPP and Multichassis Multilink PPP.
Examples
The following example shows how to configure the Cisco Multihop VPDN feature:
!vpdn enablevpdn multihopvpdn search-order domain!vpdn-group 1request-dialinprotocol l2tpdomain cisco.cominitiate-to ip 172.22.53.144 priority 1initiate-to ip 172.22.53.145 priority 1!l2tp tunnel password 7 secret!The following example shows how to configure DNIS-based multihop capability:
!vpdn enablevpdn multihop!vpdn-group 1accept-dialinprotocol l2tp/l2fvirtual-template 1terminate-from hostname LAC-1local name Multi-Hopvpdn-group 2request-dialinprotocol l2tp/l2fdnis 5555555initiate-to ip 10.10.1.1local name Multi-Hop!The following example shows a configuration where a packet traverses a VPDN tunnel over a service provider link, and then a second tunnel by traversing a hop between home gateways on the corporate network. The bundle owner is Home-Gateway1 and the stack group peer, Home-Gateway2, is specified as a peer (1.1.1.2).
vpdn multihopusername stack password hellotheremultilink virtual-template 1sgbp group stacksgbp member Home-Gateway2 1.1.1.2interface virtual-template 1ip unnumbered e0ppp multilinkppp auth chapRelated Commands
vpdn outgoing
The vpdn outgoing command is replaced by the request-dialin command. See the description of the request-dialin command for more information.
vpdn profile
To associate a virtual private dialup network (VPDN) profile with a customer profile, use the vpdn profile command in customer profile configuration mode. To remove a VPDN profile from a customer profile, use the no form of this command.
vpdn profile name
no vpdn profile name
Syntax Description
Defaults
No default behavior or values.
Command Modes
Customer profile configuration
Command History
12.0(4)XI
This command was introduced.
12.0(5)T
Support for this command was integerated into Cisco IOS Release 12.0(5)T.
Usage Guidelines
Use the vpdn profile command to associate a VPDN profile with a customer profile.
VPDN profiles can be used to combine session counting over multiple VPDN groups. This ability can be applied to customer profiles by configuring multiple VPDN groups under a VPDN profile, then associating the VPDN profile with the customer profile using the vpdn profile command.
Examples
The following example shows how to create two VPDN groups, configure the VPDN groups under a VPDN profile named profile1, then associates the VPDN profile with a customer profile named customer12:
Router(config)# vpdn-group 1Router(config-vpdn)#!Router(config)# vpdn-group 2Router(config-vpdn)#!Router(config)# resource-pool profile vpdn profile1Router(config-vpdn-profile)# vpdn group 1Router(config-vpdn-profile)# vpdn group 2!Router(config)# resource-pool profile customer customer12Router(config-vpdn-customer)# vpdn profile profile1Related Commands
vpdn redirect identifier
To configure a virtual private dialup network (VPDN) redirect identifier to use for Layer 2 Tunneling Protocol (L2TP) call redirection on a stack group tunnel server, use the vpdn redirect identifier command in global configuration mode. To remove the name of the redirect identifier from the tunnel server, use the no form of this command.
vpdn redirect identifier identifier-name
no vpdn redirect identifier identifier-name
Syntax Description
Command Default
No identifier name is configured.
Command Modes
Global configuration
Command History
12.2(8)B
This command was introduced.
12.2(13)T
This command was integrated into Cisco IOS Release 12.2(13)T.
Usage Guidelines
The vpdn redirect identifier command is configured on each of the stack group tunnel servers. To configure the name of the redirect identifier on the NAS, use the redirect identifier command in VPDN group configuration mode.
The NAS compares the configured redirect identifier with the one received from the stack group tunnel server to determine authorization information to redirect the call.
Configuring the redirect identifier is not necessary to perform redirects. If the redirect identifier is not configured, the NAS uses the redirect IP address in order to get authorization information to redirect the call. In that case, the IP address of the new redirected tunnel server must be present in the initiate-to command configuration of the VPDN group on the NAS.
The redirect identifier allows new stack group members to be added without the need to update the NAS configuration with their IP addresses. With the redirect identifier configured, a new stack group member can be added and given the same redirect identifier as the rest of the stack group.
If the authorization information for getting to the new redirected tunnel server is different, then you will need to configure the authorization information via RADIUS using tagged attributes:
Cisco:Cisco-Avpair = :0:"vpdn:vpdn-redirect-id=identifier name"The NAS will choose the correct tagged parameters to get authorization information for the new redirected tunnel server by first trying to match the redirect identifier (if present) or else by matching the Tunnel-Server-Endpoint IP address.
Examples
The following example configures the redirect identifier named lns1 on a stack group tunnel server:
Router(config)# vpdn redirect identifier lns1The following attribute-value (AV) pair configures the RADIUS server with the redirect identifier named lns1 for a tunnel server:
Cisco:Cisco-Avpair = :0:"vpdn:vpdn-redirect-id=lns1"Related Commands
vpdn redirect attempts
To restrict the number of redirect attempts possible for a given Layer 2 Tunneling Protocol (L2TP) call on the L2TP access concentrator (LAC), use the vpdn redirect attempts command in global configuration mode. To revert to the default of three redirect attempts, use the no form of this command.
vpdn redirect attempts number-of-attempts
no vpdn redirect attempts number-of-attempts
Syntax Description
Defaults
Three redirect attempts
Command Modes
Global configuration
Command History
12.2(8)B
This command was introduced.
12.2(13)T
This command was integrated into Cisco IOS Release 12.2(13)T.
Usage Guidelines
Note that the number of redirect attempts is by default always restricted to three, even if this command is not explicitly configured. The only use of this command is to configure a redirect attempts value other than the default (which is always in effect).
Examples
The following example configures four redirect attempts:
Router(config)# vpdn redirect attempts 4Related Commands
vpdn redirect identifier
To indicate the name of the virtual private dialup network (VPDN) redirect identifier to use for Layer 2 Tunneling Protocol (L2TP) call redirection, use the vpdn redirect identifier command in global configuration mode. To remove the name of the redirect identifier from the L2TP network server (LNS) of the stack group, use the no form of this command.
vpdn redirect identifier identifier-name
no vpdn redirect identifier identifier-name
Syntax Description
Defaults
No identifier name is configured.
Command Modes
Global configuration
Command History
12.2(8)B
This command was introduced.
12.2(13)T
This command was integrated into Cisco IOS Release 12.2(13)T.
Usage Guidelines
The vpdn redirect identifier command is configured on the L2TP access concentrator (LAC) and the stack group LNSs. The LAC compares this identifier with the one received from the stack group LNS to determine authorization information to redirect the call.
Note that configuring the redirect identifiers is not necessary in order to do redirects. If redirect identifiers are not configured, the LAC uses the new received redirect IP address to get authorization information to redirect the call. In that case, the IP address of the new redirected LNS must be present in the vpdn-group and initiate-to commands for the LAC configuration.
The redirect identifier allows new stack group members to be added without the need to update the LAC configuration with their IP addresses (which would be needed for redirect authorization). Now, you can add a new stack group member and give it the same redirect identifier as the rest of the stack group. The LAC configuration then need not be updated. Note that if the authorization information for getting to the new redirected LNS is different, then you will need to configure the authorization information via RADIUS using tagged attributes, as follows:
Cisco:Cisco-Avpair = :0:"vpdn:vpdn-redirect-id=<identifier name>"
The LAC will then choose the correct tagged parameters to get authorization information for the new redirected LNS by first trying to match the redirect identifier (if present) or else by matching the Tunnel-Server-Endpoint IP address.
Examples
The following example configures the redirect identifier for LNS1:
Router(config)# vpdn redirect identifier LNS1The following AV pair configures the RADIUS server with the redirect identifier for LNS1:
Cisco:Cisco-Avpair = :0:"vpdn:vpdn-redirect-id=idforLNS1"The following example configures the redirect identifier on the LAC:
Router(config-vpdn)# vpdn-group 1...Router(config)# redirect identifier lns1Related Commands
vpdn redirect source
To configure the public redirect IP address of an L2TP network server (LNS), use the vpdn redirect source command in global configuration mode. To remove the public redirect IP address of an LNS, use the no form of this command.
vpdn redirect source redirect-ip-address
no vpdn redirect source redirect-ip-address
Syntax Description
Defaults
If the vpdn redirect source command is not configured, then the IP address used for Stack Group Bidding Protocol (SGBP) bidding itself will be used as the redirect address (the public redirect address is then omitted in the bid response).
Command Modes
Global configuration
Command History
12.2(8)B
This command was introduced.
12.2(13)T
This command was integrated into Cisco IOS Release 12.2(13)T.
Usage Guidelines
On the LAC, this command will have no significance.
Examples
The following example configures a public IP address as a redirect source:
Router(config)# vpdn redirect source 255.255.1.1Related Commands
vpdn search-order
To specify how the service provider network access server is to perform virtual private dialup network (VPDN) tunnel authorization searches, use the vpdn search-order command in global configuration mode. To remove a prior specification, use the no form of this command.
vpdn search-order {dnis domain | domain dnis | domain | dnis}
no vpdn search-order
Syntax Description
Defaults
When this command is not used, the default is to search first on the Dialed Number Information Service (DNIS) information provided on ISDN lines and then search on the domain name. This is equivalent to using the vpdn search-order dnis domain command.
Command Modes
Global configuration
Command History
Usage Guidelines
VPDN authorization searches are performed only as specified.
The configuration shows the vpdn search-order command setting only if the command is explicitly configured.
Examples
The following example configures a network access server to select a tunnel destination based on the use of DNIS and a specific dialed number and to perform tunnel authorization searches based on the DNIS information only.
vpdn enablevpdn outgoing dnis 2387765 gocardinal ip 172.16.44.56vpdn search-order dnisRelated Commands
vpdn session-limit
To limit the number of simultaneous VPN sessions that can be established on a router, use the vpdn session-limit command in global configuration mode. To allow an unlimited number of simultaneous VPN sessions, use the no form of this command.
vpdn session-limit sessions
no vpdn session-limit
Syntax Description
Defaults
Disabled
Command Modes
Global configuration
Command History
Usage Guidelines
When this command is enabled, use the show vpdn history failure command to view records of refused attempts to establish new sessions.
Examples
The following example first sets a limit of two simultaneous VPN sessions on the router and then shows a Syslog message stating that an attempt to establish a new session was refused:
Router(config)# vpdn session-limit 2Router(config)#00:11:17:%VPDN-6-MAX_SESS_EXCD:L2F HGW great_went exceeded configured local session-limit and rejected user wilson@soam.comRouter(config)#Related Commands
Displays the content of the failure history table.
Prevents new sessions from being established on a VPN tunnel without disturbing existing sessions.
vpdn softshut
To prevent new sessions from being established on a VPN tunnel without disturbing existing sessions, use the vpdn softshut command in global configuration mode. To return the VPN tunnel to active service, use the no form of this command.
vpdn softshut
no vpdn softshut
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled
Command Modes
Global configuration
Command History
Usage Guidelines
When this feature is enabled on a NAS, the potential session will be authorized before it is refused. This authorization ensures that accurate accounting records can be kept.
When this feature is enabled on a home gateway, the reason for the session refusal will be returned to the NAS. This information is recorded in the VPN history failure table.
When this command is enabled, use the show vpdn history failure command to view records of refused attempts to establish new sessions.
Examples
The following example first enables the vpdn softshut command and then shows a Syslog message stating that an attempt to establish a new session was refused:
Router(config)# vpdn softshutRouter(config)#00:11:17:%VPDN-6-SOFTSHUT:L2F HGW great_went has turned on softshut and rejected user wilson@soam.comRouter(config)#Related Commands
Displays the content of the failure history table.
Limits the number of simultaneous VPN sessions that can be established on a router.
vpdn source-ip
To set the source IP address of the network access server, use the vpdn source-ip command in global configuration mode. To disable this function, use the no form of this command.
vpdn source-ip ip-address
no vpdn source-ip ip-address
Syntax Description
Defaults
This command is disabled. No default IP address is provided.
Command Modes
Global configuration
Command History
Usage Guidelines
One source IP address is configured on the network access server. The source IP address is configured per network access server, not per domain.
Examples
This example enables VPDN on the network access server and sets an IP source address of 172.24.48.3:
vpdn enablevpdn source-ip 172.24.48.3Related Commands
vpdn-group
To create a virtual private dialup network (VPDN) group and to enter VPDN group configuration mode, use the vpdn-group command in global configuration mode. To delete a VPDN group, use the no form of this command.
vpdn-group name
no vpdn-group name
Syntax Description
Defaults
No VPDN groups are defined.
Command Modes
Global configuration
Command History
12.0(4)XI
This command was introduced.
12.0(5)T
This command was integrated into Cisco IOS Release 12.0(5)T.
Usage Guidelines
Issuing the vpdn-group command creates a VPDN group with the specified name and enters VPDN group configuration mode. If a VPDN group with the specified name already exists, issuing the vpdn-group command will enter VPDN group configuration mode and allow configuration of that VPDN group.
A VPDN group can be associated with a customer profile or a VPDN profile by issuing the vpdn group command in customer profile configuration mode or VPDN profile configuration mode.
Examples
The following example creates the VPDN group named l2tp and enters VPDN group configuration mode:
Router(config)# vpdn-group l2tpRouter(config-vpdn)#The following example associates the VPDN group created in the preceding example with the VPDN profile named profile1:
Router(config)# resource-pool profile vpdn profile1Router(config-vpdn-profile)# vpdn group l2tpThe following example creates a VPDN group named l2f and associates it with the customer profile named customer1:
Router(config)# vpdn-group l2f!Router(config)# resource-pool profile customer customer1Router(config-customer-profile)# vpdn group l2fRelated Commands
vpdn-template
To enter VPDN template configuration mode to configure a virtual private dialup network (VPDN) default group template, use the vpdn-template command in global configuration mode. To inactivate the use of a VPDN template, use the no form of this command.
vpdn-template [name]
no vpdn-template [name]
Syntax Description
Defaults
No VPDN template exists. The system default values are applied to individual VPDN groups for any parameters that are not configured in the individual VPDN group.
Command Modes
Global configuration
Command History
12.2(4)B
This command was introduced on the Cisco 7200 series and Cisco 7401ASR routers.
12.2(8)T
This command was integrated into Cisco IOS Release 12.2(8)T.
Usage Guidelines
Use this command to configure global default values for VPDN parameters in a VPDN template. These global default values are applied to all VPDN groups, unless specific values are configured for individual VPDN groups. VPDN parameters that are not specified in the individual VPDN group or in the VPDN template are assigned system default values.
The default hierarchy for the application of VPDN parameters to a VPDN group follows:
•
•
•
Not all commands that are available for configuring a VPDN group can be used to configure a VPDN template.
Table 139 lists the commands that can be used to configure the VPDN template.
Examples
The following example shows how to enter VPDN template configuration mode and configure two VPDN parameters in the VPDN template:
vpdn-templatel2tp tunnel busy timeout 65l2tp tunnel password 7 tunnel4meThe following example shows how to configure a VPDN template called customer1 and apply a group session limit of 50 to all VPDN groups attached to that VPDN template:
vpdn-template customer1group session-limit 50Related Commands
vpn
To specify that the source and destination IP addresses of a given virtual private dialup network (VPDN) group belong to a specified VPN routing and forwarding instance (VRF), use the vpn command in VPDN group configuration mode. To disassociate all IP addresses in a VPDN group with a VRF, use the no form of this command.
vpn {vrf vrf-name | id vpn-id}
no vpn {vrf vrf-name | id vpn-id}
Syntax Description
Defaults
No default behavior or values
Command Modes
VPDN group configuration
Command History
Usage Guidelines
When you enter the vpn command you are configuring the Cisco IOS software to look up an IP destination or source address in a specific VPN routing table rather than a global routing table. The VRF to which the IP addresses of a VPDN group are associated will be the VRF that has been specified from the ip vrf command.
The vpn command can be used with dial-in and dial-out.
Examples
The following example associates IP addresses in vpdn-group 1 with the VRF `vrf-second':
vpdn-group 1request-dialinprotocol l2tp!vpn vrf vrf-secondsource-ip 172.1.1.9initiate-to ip 172.1.1Because you can also use the VPN ID to configure a VRF, you can associate the IP addresses in the VPDN group with the VPN ID. The following example associates the IP addresses in vpdn-group 2 with the VPN ID 11:2222:
vpdn-group 2request-dialinprotocol l2tp!vpn id 11:2222source-ip 172.1.1.9initiate-to ip 172.1.1.1Related Commands
vty-async
To configure all virtual terminal lines on a router to support asynchronous protocol features, use the vty-async command in global configuration mode. To disable asynchronous protocol features on virtual terminal lines, use the no form of this command.
vty-async
no vty-async
Syntax Description
This command has no arguments or keywords.
Defaults
By default, asynchronous protocol features are not enabled on virtual terminal lines.
Command Modes
Global configuration
Command History
Usage Guidelines
The vty-async command extends asynchronous protocol features from physical asynchronous interfaces to virtual terminal lines. Normally, SLIP and PPP can function only on asynchronous interfaces, not on virtual terminal lines. However, extending asynchronous functionality to virtual terminal lines permits you to run SLIP and PPP on these virtual asynchronous interfaces. One practical benefit is the ability to tunnel SLIP and PPP over X.25 PAD, thus extending remote node capability into the X.25 area. You can also tunnel SLIP and PPP over Telnet or LAT on virtual terminal lines. To tunnel SLIP and PPP over X.25, LAT, or Telnet, you use the protocol translation feature in the Cisco IOS software.
To tunnel SLIP or PPP inside X.25, LAT, or Telnet, you can use two-step protocol translation or one-step protocol translation, as follows:
•
•
Examples
The following example enables asynchronous protocol features on virtual terminal lines:
vty-asyncRelated Commands
vty-async dynamic-routing
To enable dynamic routing on all virtual asynchronous interfaces, use the vty-async dynamic-routing command in global configuration mode. To disable asynchronous protocol features on virtual terminal lines, and therefore disable routing on virtual terminal lines, use the no form of this command.
vty-async dynamic-routing
no vty-async dynamic-routing
Syntax Description
This command has no arguments or keywords.
Defaults
Dynamic routing is not enabled on virtual asynchronous interfaces.
Command Modes
Global configuration
Command History
Usage Guidelines
This feature enables IP routing on virtual asynchronous interfaces. When you issue this command and a user later makes a connection to another host using SLIP or PPP, the user must specify /routing on the SLIP or PPP command line.
If you had not previously entered the vty-async command, the vty-async dynamic-routing command creates virtual asynchronous interfaces, and then enables dynamic routing on them.
Examples
The following example enables dynamic routing on virtual asynchronous interfaces:
vty-async dynamic-routingRelated Commands
Enables manually configured routing on an asynchronous interface.
Enables manually configured routing on an asynchronous interface.
vty-async header-compression
To compress the headers of all TCP packets on virtual asynchronous interfaces, use the vty-async header-compression command in global configuration mode. To disable virtual asynchronous interfaces and header compression, use the no form of this command.
vty-async header-compression [passive]
no vty-async header-compression
Syntax Description
Defaults
Header compression is not enabled on virtual asynchronous interfaces.
Command Modes
Global configuration
Command History
Usage Guidelines
This feature compresses the headers on TCP/IP packets on virtual asynchronous connections to reduce the size of the packets and to increase performance.This feature only compresses the TCP header, so it has no effect on UDP packets or other protocol headers. The TCP header compression technique, described fully in RFC 1144, is supported on virtual asynchronous interfaces using SLIP or PPP encapsulation. You must enable compression on both ends of a connection.
Examples
The following example compresses outgoing TCP packets on virtual asynchronous interfaces only if incoming TCP packets are compressed:
vty-async header-compression passiveRelated Commands
vty-async ipx ppp-client loopback
To enable IPX-PPP on virtual terminal lines, use the vty-async ipx ppp-client loopback command in global configuration mode. To disable IPX-PPP sessions on virtual terminal lines, use the no form of this command.
vty-async ipx ppp-client loopback number
no vty-async ipx ppp-client loopback
Syntax Description
number
Number of the loopback interface configured for IPX to which the virtual terminal lines are assigned.
Defaults
IPX over PPP is not enabled on virtual terminal lines.
Command Modes
Global configuration
Command History
Usage Guidelines
This command enables users to log into the router from a device running a virtual terminal protocol, then issue the PPP command at the EXEC prompt to connect to a remote device.
A loopback interface must already have been defined and an IPX network number must have been assigned to the loopback interface before the vty-async ipx ppp-client loopback command will permit IPX-PPP on virtual terminal lines.
Examples
The following example enables IPX over PPP on virtual terminal lines:
ipx routing ramanainterface loopback0ipx network 12345vty-async ipx ppp-client loopback0Related Commands
interface loopback
Creates a loopback interface.
ipx network
Enables IPX routing on a particular interface and optionally selects the type of encapsulation (framing).
vty-async keepalive
To change the frequency of keepalive packets on all virtual asynchronous interfaces, use the vty-async keepalive command in global configuration mode. To disable asynchronous protocol features on virtual terminal lines, use the no vty-async keepalive command. To disable keepalive packets on virtual terminal lines, use the vty-async keepalive 0 command.
vty-async keepalive seconds
no vty-async keepalive
vty-async keepalive 0
Syntax Description
Defaults
Keepalive is disabled.
Command Modes
Global configuration
Command History
Usage Guidelines
Use this command to change the frequency of keepalive updates on virtual asynchronous interfaces, or to disable keepalive updates. To determine if keepalive is enabled on an interface, use the show running-config command. If the router has not received a keepalive packet after three update intervals have passed, the connection is considered down.
Examples
The following example sets the keepalive interval to 30 seconds:
vty-async keepalive 30The following example sets the keepalive interval to 0 (off):
vty-async keepalive 0Related Commands
keepalive
Sets the keepalive timer for a specific interface.
show running-config
Displays the contents of the currently running configuration file.
vty-async mtu
To set the maximum transmission unit (MTU) size on virtual asynchronous interfaces, use the vty-async mtu command in global configuration mode. To disable asynchronous protocol features on virtual terminal lines, use the no form of this command.
vty-async mtu bytes
no vty-async
Syntax Description
bytes
MTU size of IP packets that the virtual asynchronous interface can support. The default MTU is 1500 bytes. Valid values for the MTU range from 64 bytes to 1,000,000 bytes.
Defaults
1500 bytes
Command Modes
Global configuration
Command History
Usage Guidelines
Use this command to modify the MTU for packets on a virtual asynchronous interfaces. You might want to change to a smaller MTU size for IP packets transmitted on a virtual terminal line configured for asynchronous functions for any of the following reasons:
•
•
•
Do not change the MTU size unless the SLIP or PPP implementation running on the host at the other end of the virtual asynchronous interface supports reassembly of IP fragments. Because each fragment occupies a spot in the output queue, it might also be necessary to increase the size of the SLIP or PPP hold queue if your MTU size is such that you might have a high amount of packet fragments in the output queue.
Examples
The following example sets the MTU for IP packets to 256 bytes:
vty-async mtu 256Related Commands
vty-async ppp authentication
To enable PPP authentication on virtual asynchronous interfaces, use the vty-async ppp authentication command in global configuration mode. To disable PPP authentication, use the no form of this command.
vty-async ppp authentication {chap | pap}
no vty-async ppp authentication {chap | pap}
Syntax Description
chap
Enables CHAP on all virtual asynchronous interfaces.
pap
Enables PAP on all virtual asynchronous interfaces.
Defaults
No CHAP or PAP authentication for PPP.
Command Modes
Global configuration
Command History
Usage Guidelines
This command configures the virtual asynchronous interface to either authenticate CHAP or PAP while running PPP. After you have enabled CHAP or PAP, the local router requires a password from remote devices. If the remote device does not support CHAP or PAP, no traffic will be passed to that device.
Examples
The following example enables CHAP authentication for PPP sessions on virtual asynchronous interfaces:
vty-async ppp authentication chapRelated Commands
vty-async ppp use-tacacs
To enable TACACS authentication for PPP on virtual asynchronous interfaces, use the vty-async ppp use-tacacs command in global configuration mode. To disable TACACS authentication on virtual asynchronous interfaces, use the no form of this command.
vty-async ppp use-tacacs
no vty-async ppp use-tacacs
Syntax Description
This command has no arguments or keywords.
Defaults
TACACS for PPP is disabled.
Command Modes
Global configuration
Command History
Usage Guidelines
This command requires the extended TACACS server.
After you have enabled TACACS, the local router requires a password from remote devices.
This feature is useful when integrating TACACS with other authentication systems that require a clear-text version of a user's password. Such systems include one-time password systems and token card systems.
If the username and password are contained in the CHAP password, the CHAP secret is not used by the router. Because most PPP clients require that a secret be specified, you can use any arbitrary string; Cisco IOS software ignores it.
You cannot enable TACACS authentication for SLIP on asynchronous or virtual asynchronous interfaces.
Examples
The example enables TACACS authentication for PPP sessions:
vty-async ppp use-tacacsRelated Commands
ppp use-tacacs
Enables TACACS for PPP authentication.
Enables PPP authentication on virtual asynchronous interfaces.
vty-async virtual-template
To configure virtual terminal lines to support asynchronous protocol functions based on the definition of a virtual interface template, use the vty-async virtual-template command in global configuration mode. To disable virtual interface templates for asynchronous functions on virtual terminal lines, use the no form of this command.
vty-async virtual-template number
no vty-async virtual-template
Syntax Description
Defaults
Asynchronous protocol features are not enabled by default on virtual terminal lines.
Command Modes
Global configuration
Command History
10.3
The vty-async command was introduced.
11.3
The vty-async virtual-template command was introduced.
Usage Guidelines
The vty-async virtual-template command enables you to support tunneling of SLIP or PPP across X.25, TCP, or LAT networks by using two-step protocol translation.
Before issuing the vty-async virtual-template command, create and configure a virtual interface template by using the interface virtual-template command. Configure this virtual interface as a regular asynchronous serial interface. That is, assign the virtual interface template the IP address of the Ethernet interface, and configure addressing, just as on an asynchronous interface. You can also enter commands in interface configuration mode that compress TCP headers or configure CHAP authentication for PPP.
After creating a virtual interface template, apply it by issuing the vty-async virtual-template command. When a user dials in through a virtual terminal line, the router creates a virtual access interface, which is a temporary interface that supports the asynchronous protocol configuration specified in the virtual interface template. This virtual access interface is created dynamically, and is freed up as soon as the connection drops.
Before virtual templates were implemented, you could use the vty-async command to extend asynchronous protocol functions from physical asynchronous interfaces to virtual terminal lines. However, in doing so, you created a virtual asynchronous interface, rather than the virtual access interface. The difference is that the virtual asynchronous interfaces are allocated permanently, whereas the virtual access interfaces are created dynamically when a user calls in and closed down when the connection drops.
You can have up to 25 virtual templates interfaces, but you can apply only one template to vty-async interfaces on a router. There can be up to 300 virtual access interfaces on a router.
Examples
The following example enables asynchronous protocol features on virtual terminal lines:
vty-asyncvty-async virtual-template 1vty-async dynamic-routingvty-async header-compression!interface virtual-template1ip unnumbered Ethernet0encapsulation pppno peer default ip addressppp authentication chapRelated Commands
x25 aodi
To enable the Always On/Dynamic ISDN (AO/DI) client on an interface, use the x25 aodi command in interface configuration mode. To remove AO/DI client functionality, use the no form of this command.
x25 aodi
no x25 aodi
Syntax Description
This command has no arguments or keywords.
Defaults
AO/DI client is not enabled.
Command Modes
Interface configuration
Command History
Usage Guidelines
Use this command to enable the AO/DI client on an interface.
Examples
The following example enables the AO/DI client on the interface running X.25, using the x25 aodi command:
interface bri0isdn x25 dchannelisdn x25 static-tei 8interface bri0:0x25 aodix25 address 12135551234x25 htc 4x25 win 3x25 wout 3x25 map ppp 12135556789 interface dialer 1
Note
Related Commands
isdn x25 dchannel
Creates a configurable interface for X.25 traffic over the ISDN D channel.
x25 map ppp
To enable a PPP session over the X.25 protocol, use the x25 map ppp command in interface configuration mode. To remove a prior mapping, use the no form of this command.
x25 map ppp x121-address interface cloning-interface [no-outgoing]
no x25 map ppp x121-address interface cloning-interface [no-outgoing]
Syntax Description
Defaults
Disabled
Command Modes
Interface configuration
Command History
Usage Guidelines
Use x25 map ppp command to allow a PPP session to run over X.25.
The interface keyword refers to the interface that will be used to clone the configuration.
Note
Examples
Client Examples
The following example enables the AO/DI client on the interface and configures the D channel (BRI interface 0:0) with the x25 map statement in order to allow PPP sessions over X.25 encapsulation with the configured AO/DI server:
interface BRI0:0x25 address 16193368208 x25 aodi x25 htc 4 x25 win 3 x25 wout 3 x25 map ppp 16193368209 interface dialer 1Server Examples
The following example enables the AO/DI server to receive calls from the AO/DI client and configures the D channel (BRI0:0) with the x25 map statement which allows PPP sessions over X.25 encapsulation with the configured AO/DI client. The no-outgoing option is used with the x.25 map command since the AO/DI server is receiving, versus initiating, calls.
interface BRI0:0 x25 address 16193368209 x25 htc 4 x25 win 3 x25 wout 3 x25 map ppp 16193368208 interface dialer 1 no-outgoing
Note
Related Commands
isdn x25 dchannel
Creates a configurable interface for X.25 traffic over the ISDN D channel.
