Table Of Contents
C10K_MULTILINK_FRAGSIZE_BELOW_MIN_WARNING Messages
C10K_QUEUE_CFG_GENERAL Messages
C6K_MWAM_CENTRALIZED_CONFIG Messages
CWAN_CONTAINER_ACCESS Messages
System Messages
This section lists messages alphabetically by facility and mnemonic.
AAA Messages
The following are authentication, authorization, and accounting messages.
Error Message%AAA-3-ACCT_IOMEM_LOW : AAA ACCT process suspended : low I/O memory
Explanation AAA ACCT process has been suspended due to insufficient IO memory.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-ACCT_LOW_MEM_TRASH : AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records
Explanation Dropping the accounting request as there is not enough processor memory. All queued accounting requests will be trashed.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-ACCT_LOW_MEM_UID_FAIL : AAA unable to create UID for incoming calls due to insufficient processor memory
Explanation Stopped creating the AAA UID, due to LOW processor memory.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-6-ACCTSESSIDWRAP : Accounting-Session-ID [dec] exceeded max value allowed
Explanation Accounting-Session-ID value exceeded maximum value allowed. Now it is wrapping.
Recommended Action Information message only. No action is required.
Error Message%AAA-3-ATTRFORMATERR : Attribute with unknown format [dec]
Explanation An attribute was found with an invalid format.
Recommended Action Attribute with unknown format in definition. Enable AAA debug and try to replicate the steps to get the message. If the message recurs, copy the message exactly as it appears on the console or in the system log. Enter the Show tech-support command to gather data that might help identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-AUTH_LOW_IOMEM : RADIUS process is unable to handle the requests due to insufficient I/O memory
Explanation RADIUS process unable to handle request due to insufficient IO memory.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-BADMAGIC : Data structure failed magic number sanity check
Explanation A corrupted data structure has been found which was stored internally.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-BADMETHOD : Cannot process [chars] method [int]
Explanation A method list function encountered a method list that was unknown, or could not be handled.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-BADMETHODERROR : Cannot process [chars] method [chars]
Explanation A method list function encountered a method type that was unknown, or could not be handled.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-BUFFER_OVERFLOW : Radius I/O buffer has overflowed
Explanation An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer.
Recommended Action This is an internal software error. Copy the message exactly as it appears on the console or in the system log. Enter the Show tech-support command to gather data that might help identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-DROPACCTFAIL : Accounting record dropped, send to server failed: [chars]
Explanation An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this could be the servers might not be operational or the NAS is not configured properly.
Recommended Action Check the server , whether they are operational or not. Next check whether the device is configured properly. Refer tothe server configuration section of the cisco IOS documentation. Finally, check that the NAS can communicate with the server. If the mesaage recurs, copy the message exactly as it appears on the console or in the system log. Enter the show running-config command to gather data that might help identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-2-FORKFAIL : Cannot fork process [chars]
Explanation Attempted to fork a process and failed. The reason could be either hardware or software.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-HA_INIT_FAILURE : High availability initialization failure: [chars]
Explanation The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device, sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-HA_INTERNAL_ERROR : High availability internal error for unique id [hex]: [chars]
Explanation The AAA subsystem has suffered an internal error. In the event of switchover to a standby device, sessions depending on high availability capabilities in the AAA subsystem might be forced to renegotiate.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-6-INVALIDROUTE : Syntax error in route statement: [chars]
Explanation Currently downloading route contains syntax error.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-IPILLEGALMSG : Invalid use of ip_pid([int])
Explanation This error means a process sent an illegal message.
Recommended Action If this message recurs, check bug toolkit on Cisco website for the issue. If you did not find one, copy the message exactly as it appears on the console or in the system log. Enter the Show tech-support command to gather data that might help identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-ISDNINTF : [chars] [chars]: Can not apply configuration to ISDN channel:
"[chars]"Explanation Configuration cannot be applied to individual ISDN channels.
Recommended Action You need virtual-profiles and virtual-access interfaces to apply configuration to ISDN. Refer to the section on "Configuring virtual profile by AAA Configuration" in the Cisco IOS Dial Technologies Configuration Guide.
Error Message%AAA-3-LOW_MEM : [chars] process is unable to handle the incoming packet due to low memory
Explanation Check the processor memory or IO memory. Most likely one of them has less available memory or, worst case, both might have insufficient memory.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-MLIST_TOO_MANY_METHODS : method list '[chars]'
Explanation This is an internal software error. An AAA client attempted to add too many methods to a method list.
Recommended Action This is an internal software error. Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-NULLCURSOR : Null cursor
Explanation An AAA client has provided a nonexistent attribute cursor to AAA.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-NULLVRF : Null vrf entry
Explanation A NULL VRF entry was found while comparing the AAA VRF attributes.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-PARSEERR : Error([dec]) parser is unable to parse [chars] per-user command
Explanation All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands, to revert back. The unconfiguration might fail due to parser or AAA error.
Recommended Action The given unconfigure command was not executed. Switch on the debug peruser command and repeat the steps that caused the error. If the message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-SERVER_INTERNAL_ERROR : Server '[IP_address]': [chars]
Explanation This is an internal software error in the AAA server group subsystem.
Recommended Action This is an internal software error. Copy the message exactly as it appears on the console or in the system log. Enter the Show tech-support command to gather data that might help identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-SG_DEADTIME_FORKFAIL : Failed to fork process for [chars].
Explanation Quite likely, it ran out of memory. Other explanations are possible.
Recommended Action If this message recurs, copy the message exactly as it appears on the console or in the system log. Enter the Show tech-support command to gather data that might help to identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-SG_INTERNAL_ERROR : server group '[chars]': [chars]
Explanation This is an internal software error in the AAA server group subsystem.
Recommended Action This is an internal software error. Copy the message exactly as it appears on the console or in the system log. Enter the Show tech-support command to gather data that might help identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-3-SG_TESTPROC_FORKFAIL : Failed to fork process for [chars].
Explanation Quite likely, it ran out of memory. Other explanations are possible.
Recommended Action If this message recurs, copy the message exactly as it appears on the console or in the system log. Enter Show tech-support command to gather data that might help identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%AAA-6-USER_BLOCKED : Enable view requires to be authenticated by non-none methods,Please use the appropriate method with the login authentication
Explanation Method authentication is not allowed in CLI.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.AAAA Messages
The following are TACACS authentication, authorization, and accounting security messages.
Error Message%AAAA-3-DROPACCTFULLQ : Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars]
Explanation An accounting record was dropped because there are too many accounting packets enqueued.
Recommended Action Disable periodic accounting if it is on. The accounting queue might have grown to be large, which is usually due to a non-responsive AAA server. Enter show radius statistics or show tacacs to see if the number of timeouts is increasing, or if the response delay is unusually high.
Error Message%AAAA-3-DROPACCTQUEUEEXCEEDED : accounting record dropped, output record queue full: [chars]-[chars] [chars] [chars]
Explanation An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit.
Recommended Action Disable periodic accounting if it is on. Enter [no] aaa accounting update newinfo periodic <interval>.
Error Message%AAAA-3-SGDUPFREE : Duplicate free of server group [hex]
Explanation This is an internal software error.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.ACE Messages
The following are Allegro Crypto Engine messages.
Error Message%ACE-3-CEAL_REGISTRATION : ACE [chars] failed to register.
Explanation The ACE failed to register with CEAL.
Recommended Action Reset the hardware module.
Error Message%ACE-3-OUTOFRES : Too many [chars] in the system. Cannot allocate a new one
Explanation All VPN-accelerator resources of a particular set are in use and thus this allocation request fails.
Recommended Action Remove the cryptomap set from the interface. Reduce the number of that resource in the system. For ACL, reduce the number of ACL permit ACEs in the system. For cryptomap, reduce thenumber of cryptomaps in the system. For SPD and SPD map, reduce the number of interfaces with cryptomap set attached.
Error Message%ACE-6-UNEXP_INBOUND_IPSEC : [chars]: received unexpected IPsec packet: src IP: [IP_address]; dst IP: [IP_address]; (count=[dec])
Explanation An IPsec packet was unexpectedly forwarded to the RP.
Recommended Action If this message was seen in the context of the router booting, enabling the hardware crypto accelerator, then this message is normal and can be safely ignored. Otherwise, copy the message exactly as it appears on the console or in the system log.Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ACE-6-UNEXP_OUTBOUND_IPSEC : [chars]: received unexpected IPsec packet: src IP: [IP_address]; dst IP: [IP_address]; firsthop/lasthop = [chars]/[chars] (count=[dec])
Explanation An IPsec packet was unexpectedly forwarded to the RP.
Recommended Action If this message was seen in the context of the router booting, enabling the hardware crypto accelerator, or with an invalid peer IP address, then this message is normal and can be safely ignored. Otherwise, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.ADJ Messages
The following are adjacency subsystem messages.
Error Message%ADJ-3-TYPENOTISSUAWARE : Bundle type [chars] must be ISSU aware to send to slot(s) [chars]
Explanation The given bundle type is not ISSU aware so cannot be distributed to a slot with which ISSU negotiation has occurred. This indicates a design problem which requires code changes to fix.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ADJ-3-BADMACALIGN2 : Adjacency mac string for [chars] not byte aligned, offset [hex], length [hex]
Explanation An internal software error occurred.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ADJ-3-MACOVERFLOW : Adjacency mac address for [chars] overflowed by [dec] bytes
Explanation An internal software error occurred.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ADJ-5-PARENT : Midchain parent maintenance for [chars] - [chars]
Explanation A midchain adjacency failed to stack onto output chain because a loop was detected. Traffic through the adjacency will be dropped until the adacencyj is restacked. This condition is typically transient and is rectified by the control plane driving stacking. For example, if an ip tunnel destination resolves through the tunnel transiently this message would appear. The situation would be rectified either by learning the tunnel destination through an inteface other than the tunnel itself or by bringing the tunnel down
Recommended Action No action is required.
Error Message%ADJ-3-RESOLVE_REQ : Adj resolve request: [chars] [chars] [chars]
Explanation An internal software error occurred.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.AMD_P2_FE Messages
The following are Presidio Ethernet and Laguna Fastethernet messages.
Error Message%AMDP2_FE-3-GENERAL : [chars]
Explanation General C10K failure message.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.AP Messages
The following are Authentication Proxy messages.
Error Message%AP-4-AUTH_PROXY_NOMEM : Sufficient memory was not available to [chars]
Explanation There was not enough memory to perform the specified operation.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message%AP-6-POSTURE_DOWNLOAD_ACL : Send AAA request to download ([chars]) named access control list
Explanation This message indicates the router has sent a request to AAA to get the contents of the specified downloadable access contol list.
Recommended Action This is an informational message. No action is required.
Error Message%AP-4-POSTURE_EXCEED_MAX_INIT : Exceeded maximum limit ([dec]) on entires in authentication proxy posture cache in initializing state
Explanation This message indicates that the number of entries in authentication proxy posture cache which are in INIT state has exceeded the maximum limit.
Recommended Action This might be a potential Denial of Service attack.
Error Message%AP-6-POSTURE_POLICY : [chars] [chars] ([chars]) policy for host ([IP_address])
Explanation This message specifies the policy enforced or removed for the specified host. The policy could be either an access control list or a URL to which any intercepted HTTP traffic would be redirected.
Recommended Action This is an informational message. No action is required.
Error Message%AP-1-POSTURE_POLICY_ERROR : POLICY=[chars]| POLICYNAME=[chars]| IP=[IP_address]| ERROR=<[chars][chars]>
Explanation This message indicates that the specified policy was not applied for the given host IP due to the reason specified in the error.
Recommended Action In case of HOST ACL policy, verify if an input access list is defined and configured on interface. URL REDIRECT ACL policy needs url-redirect VSA to have an associated access control list url-redirect-acl VSA, which is used to determine HTTP redirect critera. HTTP packets matching the access control list will be subjected to redirection. In case the 'url-redirect-acl' access control list is not specified or is not configured, the host will not be setup for HTTP redirection.
Error Message%AP-6-POSTURE_START_VALIDATION : IP=[IP_address]| Interface=[chars]
Explanation This message indicates the router has created an entry for the host in authentication proxy posture cache and has initiated a posture validation process.
Recommended Action This is an informational message. No action is required.
Error Message%AP-6-POSTURE_STATE_CHANGE : IP=[IP_address]| STATE=[chars]
Explanation This message indicates the change of posture validation state of the specified host in the authentication proxy posture validation cache.
Recommended Action This is an informational message. No action is required.
ARCHIVE_DIFF Messages
The following are Archive Difference and Rollback related messages.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_BACKUP : Backing up current running config to [chars]
Explanation The current running configuration is saved so that when the timer expires, if no confirmation has been received from user to confirm what has been configured, the system will rollback to the saved configuration.
Recommended Action This message DOES NOT denote any error condition. It is a part of the normal operation of the rollback confirmed change.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CANCEL : User: [chars]: Rollback Confirmed Change is cancelled due to [chars] failure
Explanation Rollback Confirmed Change is normally configured along with other configuration operations, such as "config term" or "config replace". If those operations failed, Rollback Confirmed Change should not be activated.
Recommended Action Remove the error condition and try again later.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CONFIRM : User: [chars]: Confirm the configuration change
Explanation The configuration change is confirmed. The timer for rolling to the previously saved configurationis cancelled.
Recommended Action This message DOES NOT denote any error condition. It is a part of the normal operation of the rollback confirmed change.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_ABSTIMER : User: [chars]: Reset Rollback Confirmed Change timer(absolute) to [int] minute
Explanation Reset Rollback Confirmed Change timer(absolute) to a new value .
Recommended Action This message DOES NOT denote any error condition. It is a part of the normal operation of the rollback confirmed change.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_IDLETIMER : User: [chars] Reset Rollback Confirmed Change timer(idle) to [int] minute
Explanation Reset Rollback Confirmed Change timer(idle) to a new value.
Recommended Action This message DOES NOT denote any error condition. It is a part of the normal operation of the rollback confirmed change.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_REVERTNOW : User: [chars]: Rollback immediately.
Explanation Rollback immediately and cancel the timer.
Recommended Action This message DOES NOT denote any error condition. It is a part of the normal operation of the rollback confirmed change.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_RETRY : Failed to acquire configuration lock. Rollback did not start. Schedule to
retry in 5 minutesExplanation Failed to acquire configuration lock. Rollback did not start. In this case, retry will be scheduled.
Recommended Action This message DOES NOT denote any error condition. It is a part of the normal operation of the rollback confirmed change.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_START : Start rolling to: [chars]
Explanation The timer for Rollback Confirmed Change has expired. System will rollback to the previously saved configuration.
Recommended Action This message DOES NOT denote any error condition. It is a part of the normal operation of the rollback confirmed change.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_ABSTIMER : User: [chars]: Scheduled to rollback to config [chars] in [int] minutes
Explanation The system will wait for the user to confirm that they wish to keep what has been configured until the timer expires. If the confirmation is not received in time, the router will rollback.
Recommended Action This message DOES NOT denote any error condition. It is a part of the normal operation of the rollback confirmed change.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_IDLETIMER : User: [chars]: Scheduled to rollback to config [chars] if session has been idle for [int] minutes
Explanation The system will wait for the user to confirm that they wish to keep what has been configured until the timer expires. If the confirmation is not received in time, the router will rollback.
Recommended Action This message DOES NOT denote any error condition. It is a part of the normal operation of the rollback confirmed change.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_ABSTIMER : System will rollback to config [chars] in one minute. Enter "configure confirm" if you wish to keep what you've configured
Explanation Rollback will start in one minute. You can enter the configure confirm command if you wish to keep what has been configured.
Recommended Action This message DOES NOT denote any error condition. It is a part of the normal operation of the rollback confirmed change.
Error Message%ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_IDLETIMER : User [chars] on tty [dec] has been idle for [int] minutes. System will rollback to config [chars] in oneminute if it continues to be idle. Enter "configure confirm" if you wish to keep what you've configured
Explanation Rollback will start in one minute. You can enter the configure confirm command if you wish to keep what has been configured.
Recommended Action This message DOES NOT denote any error condition. It is a part of the normal operation of the rollback confirmed change.
ARP Messages
The following are Address Resolution Protocol (ARP) messages.
Error Message%ARP-3-ARPHAMSGFMT : Malformed ARP HA checkpointing message (size = [int], entry count = [int])
Explanation A malformed ARP HA checkpointing message has been received.
Recommended Action If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ARP-3-ARPINT : ARP table accessed at interrupt level [dec]
Explanation ARP table is accessed at interrupt level which is forbidden.
Recommended Action If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.ATA Messages
The following are Advanced Technology Attachment (ATA) messages.
Error Message%ATA-6-ATA_STATUS_TIMEOUT : Timeout occurred while querying the status of ATA device.
Explanation A timeout occurred while querying the status of ATA device.
Recommended Action Replace the new ATA device and retry the operation. If the problem persists, (1)Enter 'show tech' command.
(2) Enable file system operation logs using the following commands:
(a)'debug ifs file'
(b) 'debug ifs fs'
(c) 'debug ifs verbose'
(3) Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.ATM Messages
The following are Asynchronous Transfer Mode messages.
Error Message%ATM-3-FAILREGAUTOVC : ATM failed to register AutoVC
VC(VCD=[dec], VPI=[dec], VCI=[dec]) on Interface [chars],
(Cause of the failure: [chars])Explanation ATM has failed to register Auto VC to the driver.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ATM-3-MLPDEQUEUE : MLPPP failed CosQ=[hex], MLP=[hex], OQDQ=[hex] [hex],(Cause of the failure: [chars])
Explanation This message can occur for several related reasons. The MLP has a NULL pointer error.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ATM-3-REJECTVC : ATM failed to create VC(VCD=[dec], VPI=[dec], VCI=[dec]) on Interface [chars], (Cause of the failure: [chars])
Explanation This message occurs when platform fails to create vc with parameters passed to it.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.ATMPA Messages
The following are ATM port adapter messages.
Error Message%ATMPA-3-CMDFAIL : [chars] Command Failed at [chars] - line [dec], arg [dec]
Explanation The port adapter failed to process a command. A possible reason for this condition is an OIR operation was performed on a line card or port adapter and RP was in the process of executing commands. If this message is seen during any other time, it indicates a software problem.
Recommended Action If this message appeared while an OIR operation was being performed on a port adapter or line card, and if the slot or bay number in the message text corresponds to the removed hardware, this message indicates normal system operation and no action is required. Otherwise, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ATMPA-3-SARCRASH : [chars]: SAR[dec] SARCRASH
Explanation The SAR chip crashed and interface is being reset.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Enter the sh cont atm <xxx> command to gather data that might help identify the nature of the message.Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.ATMSPA Messages
The following are ATM Shared Port Adapter messages.
Error Message%ATMSPA-3-FATAL_ERROR : occurred on [chars]. Resetting SPA
Explanation The SPA has been reset due to a critical error in one of its devices. The error could either be a single occurrence of an event or multiple occurrences within a period of time. The message text on the console or in the system log provides more information on the specific nature of the message.
Recommended Action If the SPA is reset more than once, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information. Provide the information you have gathered and a 'show tech-support' to your support representative, or attach it to your case in non-zipped, plain text format (.txt).Error Message%ATMSPA-3-FPD_VER_DEPENDENCY_NOTE : Cannot perform the requested FPD update operation because [chars] in subslot [int]/[int] has incompatible HW version [int].[int] with FPD image version [dec].[dec] for FPD ID [dec]. Only image version greater than [int].[int] can be used in the update operation of [chars] with HW version greater than [int].[int].
Explanation The version of the FPD image from the FPD image bundle or package is not compatible with the HW version of the target card.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ATMSPA-2-INITFAIL : [chars] - Init Failed return code: [int]
Explanation The SPA failed to complete hardware initialization. One of the devices in the SPA failed to initialize successfully. Information about the failed device is specified in the message text on the console or in the system log.
Recommended Action Power down and reseat the indicated SPA card. If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information. Provide the information you have gathered and a 'show tech-support' to your support representative, or attach it to your case in non-zipped, plain text format (.txt).Error Message%ATMSPA-3-QOS_ALLOC_FAILED : [chars] [chars] [chars]: [dec]
Explanation Traffic shaping parameters could not be configured because the number of unique shaping parameters that are configured on the PVCs or PVPs in this specified ATM SPA is over the maximum limit. The maximum number of unique shaping parameters that can be configured on the PVCs or PVPs is 4096.
Recommended Action Ensure that the total number of unique shaping parameters that are configured on both PVCs and PVPs does not exceed the maximum limit of 4096.
Error Message%ATMSPA-3-VCQ_ERROR : [chars]: VC queue configuration failed due to un-initialized queue table(global identifier [dec])
Explanation Software configuration of a VC queue failed due to un-initialized queue table.
Recommended Action Attempt to perform a soft OIR operation by entering the command that is described in the shared port adapter software configuration guide. If this message recurs, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information. Also supply a 'show tech-support' at that time.Error Message%ATMSPA-4-VCSETUP : [chars]: VC setup command received on the LC for an existing VC (VCD [dec])
Explanation A command to set up a VC has been received for a VC that has already been set up. The VC has already been configured by a previous setup VC command from the RP. A duplicate setup command might indicate that the RP did not receive a response from the LC for the previous setup command.
Recommended Action No action is required.
Error Message%ATMSPA-4-VCTEARDOWN : [chars]: VC tear down command received on the LC for a non-existing VC (VCD [dec])
Explanation The VC does not exist on the LC. Most likely, it has been torn down by a previous teardown command from RP. A duplicate teardown command might indicate that the RP did not receive a response from the LC for the previous teardown command.
Recommended Action No action is required.
Error Message%ATMSPA-4-VPSETUP : [chars]: VP setup command received on the LC for an existing VP (VPI [dec])
Explanation A command to set up a VP has been received for a VP that has already been set up. The VP has already been configured by a previous setup VP command from the RP. A duplicate setup command might indicate that the RP did not receive a response from the LC for the previous setup command.
Recommended Action No action is required.
Error Message%ATMSPA-4-VPTEARDOWN : [chars]: VP tear down command received on the LC for a non-existing VP (VPI [dec])
Explanation The VP does not exist on the LC. Most likely, it has been torn down by a previous teardown command from RP. A duplicate teardown command might indicate that the RP did not receive a response from the LC for the previous teardown command.
Recommended Action No action is required.
ATOM_NP_CLIENT Messages
The following are Area Transport over MPLS NP client messages.
Error Message%ATOM_NP_CLIENT-3-INFO : [chars]
Explanation ATOM NP Client failed to initialize properly, which will result in improper operation of Any Transport Over MPLS feature.
Recommended Action Try to reload the IOS image on the affected card or platform. If the message recurs, copy the message exactly as it appears on the console or in the system log. Enter the show tech and show log commands to gather data that might help identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ATOM_NP_CLIENT-3-NOMEM : [chars]
Explanation ATOM NP Client failed to initialize properly, which will result in improper operation of Any Transport Over MPLS feature.
Recommended Action This error might indicate that more memory must be installed on the affected card or platform in order to service all the features and related entities enabled via the configuration. Try to reload the IOS image on the affected card or platform. If the message recurs, copy the message exactly as it appears on the console or in the system log. Enter the show tech and show log commands to gather data that might help identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ATOM_NP_CLIENT-4-WARN : [chars] [dec] [chars]
Explanation AToM Entry could not be added because the Entry passed is invalid.
Recommended Action Try to reload the IOS image on the affected card or platform. If the message recurs, copy the message exactly as it appears on the console or in the system log. Enter the show tech and show log commands to gather data that might help identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl, or contact your Cisco technical support representative and provide the representative with the gathered information.ATOM_SEG Messages
The following are MFI AToM segment handler messages.
Error Message%ATOM_SEG-3-CHUNKFREE : Error freeing [chars]
Explanation ATOM Segment Handler error.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl, or contact your Cisco technical support representative and provide the representative with the gathered information.ATOM_TRANS Messages
The following are Layer 2 Transport over MPLS messages.
Error Message%ATOM_TRANS-3-INIT_FAIL : Failed to start AToM Manager
Explanation Failed to start and initialize AToM Manager.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%ATOM_TRANS-3-LABEL_ALLOC_FAIL : Failed to allocate local label for peer:[IP_address], vcid:[int]
Explanation Failed to allocate local label for specified AToM VC.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.BACKPLANE_BUS_ASIC Messages
The following are backplane bus ASIC messages.
Error Message%BACKPLANE_BUS_ASIC-5-BUS_MODE_CHANGE : The System Switching Bus Mode changed to [chars] mode
Explanation The System Switching Bus Interface device has changed switching bus modes.
Recommended Action The Supervisor has instructed this line card to change the mode on the switching bus. No action is required.
Error Message%BACKPLANE_BUS_ASIC-5-BUS_SEQ_ERR : Constellation bus Sequence Error. Resetting Backplane Bus Asic.
Explanation The switch processor has detected a sequence error on the backplane bus. A reset sequence from the EARL has been called to recover from this error. System traffic should recover and continue normally.
Recommended Action If traffic recovers, no action is required. Otherwise, copy the message exactly as it appears on the console or in the system log. Enter the show platform hardware hyperion all command to gather data that might help identify the nature of the message. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%BACKPLANE_BUS_ASIC-5-DEV_INIT_FAILURE : The Backplane Bus Asic initialization failed
Explanation The Backplane Bus ASIC initialization was not successful.
Recommended Action The Backplane Bus Asic could not be initialized. As a result, this device is not operational and has been disabled. Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information. .Error Message%BACKPLANE_BUS_ASIC-5-DEV_INTR_INFO : [chars]
Explanation This message provides more information about the interrupts from the backplane bus ASIC to the line card CPU.
Recommended Action No action is required if traffic recovers. Otherwise, copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information.Error Message%BACKPLANE_BUS_ASIC-4-DEV_RESET : Backplane Bus Asic reset, interrupt [chars]
Explanation The Backplane Bus ASIC in the MSC/FlexWAN-ENH has received a fatal error. The ASIC will be reset and the MSC/FlexWAN-ENH will attempt to continue normal operation.
Recommended Action No action is required if traffic recovers. Otherwise, copy the message exactly as it appears on the console or in the system log.Research and attempt to resolve the issue using the tools and utilities provided at
http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit
http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with th