Table Of Contents

show ip mroute

show ip ospf database opaque-area

show ip ospf mpls traffic-eng

show ip pim interface

show ip protocols vrf

show ip route vrf

show ip rsvp host

show ip vrf

show isis database verbose

show isis mpls traffic-eng adjacency-log

show isis mpls traffic-eng advertisements

show isis mpls traffic-eng tunnel

show lane

show lane bus

show lane client

show ip mroute

To display the contents of the IP multicast routing table, use the show ip mroute command in EXEC mode.

show ip mroute [group-name | group-address] [source] [summary] [count] [active kbps]

Syntax Description

group-name | group-address	(Optional) IP address, name, or interface of the multicast group as defined in the DNS hosts table.
source	(Optional) IP address or name of a multicast source.
summary	(Optional) Displays a one-line, abbreviated summary of each entry in the IP multicast routing table.
count	(Optional) Displays statistics about the group and source, including number of packets, packets per second, average packet size, and bits per second.
active kbps	(Optional) Displays the rate that active sources are sending to multicast groups. Active sources are those sending at a rate of kbps or higher. The kbps argument defaults to 4.

Defaults

The show ip mroute command displays all groups and sources.
The show ip mroute active command displays all sources sending at a rate greater than or equal to 4 kbps.

Command Modes

EXEC

Command History

Release	Modification
10.0	This command was introduced.
12.0(5)T	The flag "H" was added in the output display to indicate that an outgoing interface is hardware-switched in the case of IP multicast Multilayer Switching (MLS).

Usage Guidelines

If you omit all optional arguments and keywords, the show ip mroute command displays all entries in the IP multicast routing table.

The Cisco IOS software populates the multicast routing table by creating source, group (S, G) entries from star, group (*, G) entries. The star (*) refers to all source addresses, the "S" refers to a single source address, and the "G" is the destination multicast group address. In creating (S, G) entries, the software uses the best path to that destination group found in the unicast routing table (that is, through Reverse Path Forwarding [RPF]).

Examples

The following is sample output from the show ip mroute command for a router operating in dense mode. This command displays the contents of the IP multicast routing table for the multicast group named cbone-audio.

Router# show ip mroute cbone-audio

IP Multicast Routing Table

Flags: D - Dense, S - Sparse, C - Connected, L - Local, P - Pruned

       R - RP-bit set, F - Register flag, T - SPT-bit set

Timers: Uptime/Expires

Interface state: Interface, Next-Hop, State/Mode

(*, 224.0.255.1), uptime 0:57:31, expires 0:02:59, RP is 0.0.0.0, flags: DC

  Incoming interface: Null, RPF neighbor 0.0.0.0, Dvmrp

  Outgoing interface list:

    Ethernet0, Forward/Dense, 0:57:31/0:02:52

    Tunnel0, Forward/Dense, 0:56:55/0:01:28

(198.92.37.100/32, 224.0.255.1), uptime 20:20:00, expires 0:02:55, flags: C

  Incoming interface: Tunnel0, RPF neighbor 10.20.37.33, Dvmrp

  Outgoing interface list:

    Ethernet0, Forward/Dense, 20:20:00/0:02:52

The following is sample output from the show ip mroute command for a router operating in sparse mode:

Router# show ip mroute

IP Multicast Routing Table

Flags: D - Dense, S - Sparse, C - Connected, L - Local, P - Pruned

       R - RP-bit set, F - Register flag, T - SPT-bit set

Timers: Uptime/Expires

Interface state: Interface, Next-Hop, State/Mode

(*, 224.0.255.3), uptime 5:29:15, RP is 198.92.37.2, flags: SC

  Incoming interface: Tunnel0, RPF neighbor 10.3.35.1, Dvmrp

  Outgoing interface list:

    Ethernet0, Forward/Sparse, 5:29:15/0:02:57

(198.92.46.0/24, 224.0.255.3), uptime 5:29:15, expires 0:02:59, flags: C

  Incoming interface: Tunnel0, RPF neighbor 10.3.35.1

  Outgoing interface list:

    Ethernet0, Forward/Sparse, 5:29:15/0:02:57

The following is sample output from the show ip mroute command that shows the VCD value, because an ATM interface with PIM multipoint signalling is enabled:

Router# show ip mroute 224.1.1.1

IP Multicast Routing Table

Flags: D - Dense, S - Sparse, C - Connected, L - Local, P - Pruned

       R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT

Timers: Uptime/Expires

Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 224.1.1.1), 00:03:57/00:02:54, RP 130.4.101.1, flags: SJ

  Incoming interface: Null, RPF nbr 0.0.0.0

  Outgoing interface list:

    ATM0/0, VCD 14, Forward/Sparse, 00:03:57/00:02:53

The following is sample output from the show ip mroute command with the summary keyword:

Router# show ip mroute summary

IP Multicast Routing Table

Flags: D - Dense, S - Sparse, C - Connected, L - Local, P - Pruned

       R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT

Timers: Uptime/Expires

Interface state: Interface, Next-Hop, State/Mode

(*, 224.255.255.255), 2d16h/00:02:30, RP 171.69.10.13, flags: SJPC

(*, 224.2.127.253), 00:58:18/00:02:00, RP 171.69.10.13, flags: SJC

(*, 224.1.127.255), 00:58:21/00:02:03, RP 171.69.10.13, flags: SJC

(*, 224.2.127.254), 2d16h/00:00:00, RP 171.69.10.13, flags: SJCL

  (128.9.160.67/32, 224.2.127.254), 00:02:46/00:00:12, flags: CLJT

  (129.48.244.217/32, 224.2.127.254), 00:02:15/00:00:40, flags: CLJT

  (130.207.8.33/32, 224.2.127.254), 00:00:25/00:02:32, flags: CLJT

  (131.243.2.62/32, 224.2.127.254), 00:00:51/00:02:03, flags: CLJT

  (140.173.8.3/32, 224.2.127.254), 00:00:26/00:02:33, flags: CLJT

  (171.69.60.189/32, 224.2.127.254), 00:03:47/00:00:46, flags: CLJT

The following is sample output from the show ip mroute command with the active keyword:

Router# show ip mroute active

Active IP Multicast Sources - sending >= 4 kbps

Group: 224.2.127.254, (sdr.cisco.com)

   Source: 146.137.28.69 (mbone.ipd.anl.gov)

     Rate: 1 pps/4 kbps(1sec), 4 kbps(last 1 secs), 4 kbps(life avg)

Group: 224.2.201.241, ACM 97

   Source: 130.129.52.160 (webcast3-e1.acm97.interop.net)

     Rate: 9 pps/93 kbps(1sec), 145 kbps(last 20 secs), 85 kbps(life avg)

Group: 224.2.207.215, ACM 97

   Source: 130.129.52.160 (webcast3-e1.acm97.interop.net)

     Rate: 3 pps/31 kbps(1sec), 63 kbps(last 19 secs), 65 kbps(life avg)

The following example of the show ip mroute EXEC command is displayed when IP multicast MLS is configured. Note that the "H" indicates hardware switched.

Router# show ip mroute

IP Multicast Routing Table

Flags: D - Dense, S - Sparse, C - Connected, L - Local, P - Pruned

       R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, H - Hardware 
switched

Timers: Uptime/Expires

(*, 229.10.0.1), 00:04:35/00:02:59, RP 0.0.0.0, flags: DJC

Incoming interface: Null, RPF nbr 0.0.0.0

Outgoing interface list:

	 Vlan6, Forward/Dense, 00:00:30/00:02:30

    Vlan5, Forward/Dense, 00:04:35/00:02:30

    Vlan2, Forward/Dense, 00:01:28/00:00:00

(192.0.2.20, 229.10.0.1), 00:04:35/00:02:27, flags: CT

Incoming interface: Vlan2, RPF nbr 0.0.0.0

Outgoing interface list:

    Vlan5, Forward/Dense, 00:03:25/00:00:00, H

    Vlan6, Forward/Dense, 00:00:10/00:00:00, H

Table 45 describes the significant fields shown in the output.

Table 45 show ip mroute Field Descriptions 

Field	Description
Flags:	Provides information about the entry.
D - Dense	Entry is operating in dense mode.
S - Sparse	Entry is operating in sparse mode.
C - Connected	A member of the multicast group is present on the directly connected interface.
L - Local	The router itself is a member of the multicast group.
P - Pruned	Route has been pruned. The Cisco IOS software keeps this information in case a downstream member wants to join the source.
R - RP-bit set	Indicates that the (S, G) entry is pointing toward the rendezvous point (RP). The RP is typically a prune state along the shared tree for a particular source.
F - Register flag	Indicates that the software is registering for a multicast source.
T - SPT-bit set	Indicates that packets have been received on the shortest path source tree.
H - Hardware switched	Indicates the outgoing interface is hardware switched because IP multicast MLS is enabled.
Timers:	Uptime/Expires.
Interface state:	Interface, Next-Hop or VCD, State/Mode.
(*, 224.0.255.1) (198.92.37.100/32, 224.0.255.1)	Entry in the IP multicast routing table. The entry consists of the IP address of the source router followed by the IP address of the multicast group. An asterisk (*) in place of the source router indicates all sources. Entries in the first format are referred to as (*, G) or "star comma G" entries. Entries in the second format are referred to as (S, G) or "S comma G" entries. (*, G) entries are used to build (S, G) entries.
uptime	How long (in hours, minutes, and seconds) the entry has been in the IP multicast routing table.
expires	How long (in hours, minutes, and seconds) until the entry will be removed from the IP multicast routing table on the outgoing interface.
RP	Address of the rendezvous point router. For routers and access servers operating in sparse mode, this address is always 0.0.0.0.
flags:	Information about the entry.
Incoming interface:	Expected interface for a multicast packet from the source. If the packet is not received on this interface, it is discarded.
RPF neighbor	IP address of the upstream router to the source. "Tunneling" indicates that this router is sending data to the rendezvous point encapsulated in Register packets. The hexadecimal number in parentheses indicates to which rendezvous point it is registering. Each bit indicates a different rendezvous point if multiple rendezvous points per group are used.
Dvmrp or Mroute	Indicates whether the RPF information is obtained from the DVMRP routing table or the static mroutes configuration.
Outgoing interface list:	Interfaces through which packets will be forwarded. When the ip pim nbma-mode command is enabled on the interface, the IP address of the PIM neighbor is also displayed.
Ethernet0	Name and number of the outgoing interface.
Next hop or VCD	Next hop specifies the IP address of the downstream neighbors. VCD is the virtual circuit descriptor number. VCD0 means the group is using the static-map virtual circuit.
Forward/Dense	Indicates that packets will be forwarded on the interface if there are no restrictions due to access lists or TTL threshold. Following the slash (/) is the mode in which the interface is operating (dense or sparse).
Forward/Sparse	Sparse mode interface is in forward mode.
<time/time>     (uptime/expiration time)	Per interface, how long (in hours, minutes, and seconds) the entry has been in the IP multicast routing table. Following the slash (/) is how long (in hours, minutes, and seconds) until the entry will be removed from the IP multicast routing table.

The following is sample output from the show ip mroute command with the count keyword:

Router# show ip mroute count

IP Multicast Statistics

4045 routes using 2280688 bytes of memory

41 groups, 97.65 average sources per group

Forwarding Counts:Pkt Count/Pkts per second/Avg Pkt Size/Kilobits per second

Other counts:Total/RPF failed/Other drops(OIF-null, rate-limit etc)

Group:239.0.18.1, Source count:200, Packets forwarded:348232, Packets received:348551

  RP-tree:Forwarding:12/0/218/0, Other:12/0/0

  Source:10.1.1.1/32, Forwarding:1763/1/776/9, Other:1764/0/1

  Source:10.1.1.2/32, Forwarding:1763/1/777/9, Other:1764/0/1

  Source:10.1.1.3/32, Forwarding:1763/1/783/10, Other:1764/0/1

  Source:10.1.1.4/32, Forwarding:1762/1/789/10, Other:1763/0/1

  Source:10.1.1.5/32, Forwarding:1762/1/768/10, Other:1763/0/1

  Source:10.1.1.6/32, Forwarding:1793/1/778/10, Other:1794/0/1

  Source:10.1.1.7/32, Forwarding:1793/1/763/10, Other:1794/0/1

  Source:10.1.1.8/32, Forwarding:1793/1/785/10, Other:1794/0/1

  Source:10.1.1.9/32, Forwarding:1793/1/764/9, Other:1794/0/1

  Source:10.1.1.10/32, Forwarding:1791/1/774/10, Other:1792/0/1

  Source:10.1.2.1/32, Forwarding:1689/1/780/10, Other:1691/0/2

  Source:10.1.2.2/32, Forwarding:1689/1/782/10, Other:1691/0/2

  Source:10.1.2.3/32, Forwarding:1689/1/776/9, Other:1691/0/2

.

.

.

Group:239.0.18.132, Source count:0, Packets forwarded:8810, Packets received:8810

  RP-tree:Forwarding:8810/7/780/49, Other:8810/0/0

Group:239.0.17.132, Source count:0, Packets forwarded:704491, Packets received:704491

  RP-tree:Forwarding:704491/639/782/4009, Other:704491/0/0

Group:239.0.17.133, Source count:0, Packets forwarded:704441, Packets received:704441

  RP-tree:Forwarding:704441/639/782/3988, Other:704441/0/0

Group:239.0.18.133, Source count:0, Packets forwarded:8810, Packets received:8810

  RP-tree:Forwarding:8810/8/786/49, Other:8810/0/0

Group:239.0.18.193, Source count:0, Packets forwarded:0, Packets received:0

Group:239.0.17.193, Source count:0, Packets forwarded:0, Packets received:0

Group:239.0.18.134, Source count:0, Packets forwarded:8803, Packets received:8803

  RP-tree:Forwarding:8803/8/774/49, Other:8803/0/0

---

Note The RP-tree: field is displayed only for non-Source Specific Multicast (SSM) groups that have a (*, G) entry and a positive packet received count.

---

Table 46 describes the significant fields shown in the display.

Table 46 show ip mroute count Field Descriptions 

Field	Description
Group:	Summary statistics for traffic on an IP multicast group G. This row is displayed only for non-SSM groups.
Forwarding Counts:	Statistics on the packets that are received and forwarded to at least one interface. Note There is no specific command to clear only the forwarding counters; you can clear only the actual multicast forwarding state with the clear ip mroute command. Issuing this command will cause interruption of traffic forwarding.
Pkt Count/	Total number of packets received and forwarded since the multicast forwarding state to which this counter applies was created.
Pkts per second/	Number of packets received and forwarded per second. On an IP multicast fast-switching platform, this number is the number of packets during the last second. Other platforms may use a different approach to calculate this number. Please refer to the platform documentation for more information.
Avg Pkt Size/	Total number of bytes divided by the total number of packets for this multicast forwarding state. There is no direct display for the total number of bytes. You can calculate the total number of bytes by multiplying the average packet size by the packet count.
Kilobits per second	Bytes per second divided by packets per second divided by 1000. On an IP multicast fast switching platform, the number of packets per second is the number of packets during the last second. Other platforms may use a different approach to calculate this number. Please refer to the platform documentation for more information.
Other counts:	Statistics on the received packets. These counters include statistics about the packets received and forwarded and packets received but not forwarded.
Total/	Total number of packets received.
RPF failed/	Number of packets not forwarded due to a failed RPF or acceptance check (when bidir-PIM is configured).
Other drops(OIF-null, rate-limit etc)	Number of packets not forwarded for reasons other than an RPF or acceptance check (such as the OIF list was empty or because the packets were discarded because of a configuration, such as ip multicast rate-limit, was enabled).
Group:	Summary information about counters for (*, G) and the range of (S, G) states for one particular group G. The following RP-tree: and Source: output fields contain information about the individual states belonging to this group. Note For SSM range groups, the Group: displays are statistical. All SSM range (S, G) states are individual, unrelated SSM channels.
Source count:	Number of (S, G) states for this group G. Individual (S, G) counters are detailed in the Source: output field rows.
Packets forwarded:	The sum of the packets detailed in the Forwarding Counts: fields for this IP multicast group G. This field is the sum of the RP-tree and all Source: fields for this group G.
Packets received:	The sum of packets detailed in the Other counts fields for this IP multicast group G. This field is the sum of the Other count: Pkt Count fields of the RP-tree: and Source: rows for this group G.
RP-tree:	Counters for the (*, G) state of this group G. These counters are displayed only for groups that have a forwarding mode that do not forward packets on the shared tree. These (*,G) groups are bidir-PIM and PIM-SM groups. There are no RP-tree displays for PIM-DM and SSM range groups.
Source:	Counters for an individual (S, G) state of this group G. There are no (S, G) states for bidir-PIM groups.

Related Commands

Command	Description
ip multicast-routing	Enables IP multicast routing or multicast distributed switching.
ip pim	Enables PIM on an interface.

show ip ospf database opaque-area

To display lists of information related to traffic engineering opaque link-state advertisements (LSAs), also known as Type-10 opaque link area link states, use the show ip ospf database opaque-area EXEC command.

show ip ospf database opaque-area

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Command History

Release	Modification
12.0(8)S	This command was introduced.

Examples

The following is sample output from the show ip ospf database opaque-area command:

Router# show ip ospf database opaque-area

OSPF Router with ID (25.3.3.3) (Process ID 1)

                Type-10 Opaque Link Area Link States (Area 0)

  LS age: 12

  Options: (No TOS-capability, DC)

  LS Type: Opaque Area Link

  Link State ID: 1.0.0.0

  Opaque Type: 1

  Opaque ID: 0

  Advertising Router: 24.8.8.8

  LS Seq Number: 80000004

  Checksum: 0xD423

  Length: 132

  Fragment number : 0

    MPLS TE router ID: 24.8.8.8

    Link connected to Point-to-Point network

      Link ID : 26.2.2.2

      Interface Address : 198.1.1.1

Table 47 describes the significant fields displayed in the output.

Table 47 show ip ospf database opaque-area Field Descriptions 

Field	Description
LS age	Link-state age.
Options	Type of service options.
LS Type	Type of the link state.
Link State ID	Router ID number.
Opaque Type	Opaque link-state type.
Opaque ID	Opaque LSA ID number.
Advertising Router	Advertising router ID.
LS Seq Number	Link-state sequence number that detects old or duplicate link state advertisements (LSAs).
Checksum	Fletcher checksum of the complete contents of the LSA.
Length	Length (in bytes) of the LSA.
Fragment number	Arbitrary value used to maintain multiple traffic engineering LSAs.
MPLS TE router ID	Unique MPLS traffic engineering ID.
Link ID	Index of the link being described.
Interface Address	Address of the interface.

Related Commands

Command	Description
mpls traffic-eng area	Configures a router running OSPF MPLS to flood traffic engineering for an indicated OSPF area.
mpls traffic-eng router-id	Specifies that the traffic engineering router identifier for the node is the IP address associated with a given interface.
show ip ospf mpls traffic-eng	Provides information about the links available on the local router for traffic engineering.

show ip ospf mpls traffic-eng

To display information about the links available on the local router for traffic engineering, use the show ip ospf mpls traffic-eng EXEC command.

show ip ospf [process-id [area-id]mpls traffic-eng [link] | [fragment]]

Syntax Description

process-id	(Optional) Internal identification number that is assigned locally when the OSPF routing process is enabled. The value can be any positive integer.
area-id	(Optional) Area number associated with the OSPF
link	(Optional) Provides detailed information about the links over which traffic engineering is supported on the local router.
fragment	(Optional) Provides detailed information about the traffic engineering fragments on the local router.

Defaults

No default behavior or values.

Command Modes

EXEC

Command History

Release	Modification
Release 12.0 S	This command was introduced.

Examples

The following is sample output from the show ip ospf mpls traffic-eng command:

router# show ip ospf mpls traffic-eng link

OSPF Router with ID (23.0.0.1) (Process ID 1)

  Area 0 has 2 MPLS TE links. Area instance is 14.

  Links in hash bucket 8.

    Link is associated with fragment 1. Link instance is 14

      Link connected to Point-to-Point network

      Link ID :197.0.0.1

      Interface Address :66.0.0.1

      Neighbor Address :66.0.0.2

      Admin Metric :97

      Maximum bandwidth :128000

      Maximum reservable bandwidth :250000

      Number of Priority :8

      Priority 0 :250000      Priority 1 :250000    

      Priority 2 :250000      Priority 3 :250000    

      Priority 4 :250000      Priority 5 :250000    

      Priority 6 :250000      Priority 7 :212500    

      Affinity Bit :0x0

    Link is associated with fragment 0. Link instance is 14

      Link connected to Broadcast network

      Link ID :195.1.1.2

      Interface Address :195.1.1.1

      Neighbor Address :195.1.1.2

      Admin Metric :10

      Maximum bandwidth :1250000

      Maximum reservable bandwidth :2500000

      Number of Priority :8

      Priority 0 :2500000     Priority 1 :2500000   

      Priority 2 :2500000     Priority 3 :2500000   

      Priority 4 :2500000     Priority 5 :2500000   

      Priority 6 :2500000     Priority 7 :2500000   

      Affinity Bit :0x0

Table 48 describes the significant fields shown in the output.

Table 48 show ip ospf mpls traffic-eng Field Descriptions 

Field	Description
OSPF Router with ID	Router identification number.
Process ID	OSPF process identification.
Area instance	Number of times traffic engineering information or any link changed.
Link instance	Number of times any link changed.
Link ID	Link-state ID.
Interface Address	Local IP address on the link.
Neighbor Address	IP address that is on the remote end of the link.
Admin Metric	Traffic engineering link metric.
Maximum bandwidth	Bandwidth set by the bandwidth interface interface configuration command.
Maximum reservable bandwidth	Bandwidth available for traffic engineering on this link. This value is set in the ip rsvp interface configuration command.
Number of priority	Number of priorities that are supported.
Priority	Bandwidth (in bytes per second) that is available for traffic engineering at certain priorities.
Affinity Bit	Affinity bits (color) assigned to the link.

show ip pim interface

To display information about interfaces configured for Protocol Independent Multicast (PIM), use the show ip pim interface command in EXEC mode.

show ip pim interface [type number] [count]

Syntax Description

type	(Optional) Interface type.
number	(Optional) Interface number.
count	(Optional) Number of packets received and sent out the interface.

Command Modes

EXEC

Command History

Release	Modification
11.2(11)GS	This command was introduced.
12.0(5)T	The flag "H" was added in the output display to indicate that an outgoing interface is hardware-switched in the case of IP multicast Multilayer Switching (MLS).

Usage Guidelines

This command works only on interfaces that are configured for PIM.

Examples

The following is sample output from the show ip pim interface EXEC command:

router# show ip pim interface

Address          Interface          Mode    Neighbor  Query     DR

                                            Count     Interval

198.92.37.6      Ethernet0          Dense   2         30        198.92.37.33

198.92.36.129    Ethernet1          Dense   2         30        198.92.36.131

10.1.37.2        Tunnel0            Dense   1         30        0.0.0.0

The following is sample output from the show ip pim interface command with the count keyword:

router# show ip pim interface count

Address          Interface          FS  Mpackets In/Out

171.69.121.35    Ethernet0          *   548305239/13744856

171.69.121.35    Serial0.33         *   8256/67052912

198.92.12.73     Serial0.1719       *   219444/862191

The following is sample output from the show ip pim interface command with the count keyword when IP multicast MLS is enabled. The examples lists the PIM interfaces that are fast switched and process switched, and the packet counts for these. The "H" is added to interfaces where IP multicast MLS is enabled.

router# show ip pim interface count

States: FS - Fast Switched, H - Hardware Switched

Address          Interface          FS  Mpackets In/Out

192.1.10.2       Vlan10             * H 40886/0

192.1.11.2       Vlan11             * H 0/40554

192.1.12.2       Vlan12             * H 0/40554

192.1.23.2       Vlan23             *   0/0

192.1.24.2       Vlan24             *   0/0

Table 49 describes the significant fields shown in the output.

Table 49 show ip pim interface count Field Descriptions 

Field	Description
Address	IP address of the next hop router.
Interface	Interface type and number that is configured to run PIM.
Mode	Multicast mode in which the Cisco IOS software is operating. This can be dense mode or sparse mode. DVMRP indicates that a DVMRP tunnel is configured.
Neighbor Count	Number of PIM neighbors that have been discovered through this interface. If the neighbor count is 1 for a DVMRP tunnel, the neighbor is active (receiving probes and reports).
Query Interval	Frequency (in seconds) of PIM router query messages, as set by the ip pim query-interval interface configuration command. The default is 30 seconds.
DR	IP address of the designated router on the LAN. Note that serial lines do not have designated routers, so the IP address is shown as 0.0.0.0.
FS	An asterisk (*) in this column indicates that fast switching is enabled.
Mpackets In/Out	Number of packets into and out of the interface since the box has been up.

Related Commands

Command	Description
ip pim	Enables PIM on an interface.
show ip pim neighbor	Lists the PIM neighbors discovered by the Cisco IOS software.

show ip protocols vrf

To display the routing protocol information associated with a VRF, use the show ip protocols vrf command in EXEC mode.

show ip protocols vrf vrf-name

Syntax Description

vrf-name

Name assigned to a VRF.

Defaults

No default behavior or values.

Command Modes

EXEC

Command History

Release	Modification
12.0(5)T	This command was introduced.

Usage Guidelines

Use this command to display routing information associated with a VRF.

Examples

The following example shows information about a VRF named vpn1:

router# show ip protocols vrf vpn2

Routing Protocol is "bgp 100"

  Sending updates every 60 seconds, next due in 0 sec

  Outgoing update filter list for all interfaces is 

  Incoming update filter list for all interfaces is 

  IGP synchronization is disabled

  Automatic route summarization is disabled

  Redistributing:connected, static

  Routing for Networks:

  Routing Information Sources:

    Gateway         Distance      Last Update

    13.13.13.13          200      02:20:54

    18.18.18.18          200      03:26:15

  Distance:external 20 internal 200 local 200

Table 50 describes the significant fields shown in the output.

Table 50 show ip protocols vrf Field Descriptions 

Field	Description
Gateway	Displays the IP address of the router identifier for all routers in the network.
Distance	Displays the metric used to access the destination route.
Last Update	Displays the last time the routing table was updated from the source.

Related Commands

Command	Description
show ip vrf	Displays the set of defined VRFs and associated interfaces.

show ip route vrf

To display the IP routing table associated with a VRF, use the show ip route vrf command in EXEC mode.

show ip route vrf vrf-name [connected] [protocol [as-number] [tag] [output-modifiers]] [list number [output-modifiers]] [profile] [static [output-modifiers]] [summary [output-modifiers]] [supernets-only [output-modifiers]]

Syntax Description

vrf-name	Name assigned to the VRF.
connected	(Optional) Displays all connected routes in a VRF.
protocol	(Optional) To specify a routing protocol, use one of the following keywords: bgp, egp, eigrp, hello, igrp, isis, ospf, or rip.
as-number	(Optional) Autonomous system number.
tag	(Optional) Cisco IOS routing area label.
output-modifiers	(Optional) For a list of associated keywords and arguments, use context-sensitive help.
list number	(Optional) Specifies the IP access list to display.
profile	(Optional) Displays the IP routing table profile.
static	(Optional) Displays static routes.
summary	(Optional) Displays a summary of routes.
supernets-only	(Optional) Displays supernet entries only.

Defaults

No default behavior or values.

Command Modes

EXEC

Command History

Release	Modification
12.0(5)T	This command was introduced.

Usage Guidelines

This command displays specified information from the IP routing table of a VRF.

Examples

This example shows the IP routing table associated with the VRF named vrf1:

router# show ip route vrf vrf1

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 

       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default

       U - per-user static route, o - ODR

       T - traffic engineered route

Gateway of last resort is not set

B    51.0.0.0/8 [200/0] via 13.13.13.13, 00:24:19

C    50.0.0.0/8 is directly connected, Ethernet1/3

B    11.0.0.0/8 [20/0] via 50.0.0.1, 02:10:22

B    12.0.0.0/8 [200/0] via 13.13.13.13, 00:24:20

This example shows BGP entries in the IP routing table associated with the VRF named vrf1:

Router# show ip route vrf vrf1 bgp

B  51.0.0.0/8 [200/0] via 13.13.13.13, 03:44:14

B  11.0.0.0/8 [20/0] via 51.0.0.1, 03:44:12

B  12.0.0.0/8 [200/0] via 13.13.13.13, 03:43:14

Related Commands

Command	Description
show ip cache	Displays the CEF forwarding table associated with a VRF.
show ip vrf	Displays the set of defined VRFs and associated interfaces.

show ip rsvp host

To display RSVP terminal point information for receivers or senders, use the show ip rsvp host EXEC command.

show ip rsvp host {senders | receivers} [hostname | A.B.C.D]

Syntax Description

senders	Displays information for senders.
receivers	Displays information for receivers.
hostname	(Optional) Restricts the display to sessions with hostname as their destination.
A.B.C.D	(Optional) Restricts the display to sessions with the specified IP address as their destination.

Defaults

No default behavior or values.

Command Modes

EXEC

Command History

Release	Modification
12.0(5)S	This command was introduced.

Examples

The following is sample output from the show ip rsvp host receivers command:

Router# show ip rsvp host receivers

To            From          Pro DPort Sport Next Hop      I/F   Fi Serv BPS Bytes

10.0.0.11     10.1.0.4      0   10011 1                         SE LOAD 100K  1K

Table 51 describes the significant fields shown in the output.

Table 51 show ip rsvp host Field Descriptions 

Field	Description
To	IP address of the receiver.
From	IP address of the sender.
Pro	Protocol code.
DPort	Destination port number.
Sport	Source port number.
Next Hop	IP address of the next hop.
I/F	Interface of the next hop.
Fi	Filter (wild card, shared explicit, or fixed).
Serv	Service (RATE or LOAD).
BPS	Reservation rate (in bits per second).
Bytes	Bytes of requested burst size.

Related Commands

Command	Description
show ip rsvp request	Displays the RSVP reservations currently being requested upstream for a specified interface or all interfaces.
show ip rsvp reservation	Displays RSVP-related receiver information currently in the database.
show ip rsvp sender	Displays RSVP-related sender information currently in the database.

show ip vrf

To display the set of defined VRFs and associated interfaces, use the show ip vrf command in EXEC mode.

show ip vrf [{brief | detail | interfaces}] [vrf-name] [output-modifiers]

Syntax Description

brief	(Optional) Displays concise information on the VRFs and associated interfaces.
detail	(Optional) Displays detailed information on the VRFs and associated interfaces.
interfaces	(Optional) Displays detailed information about all interfaces bound to a particular VRF, or any VRF.
vrf-name	(Optional) Name assigned to a VRF.
output-modifiers	(Optional) For a list of associated keywords and arguments, use context-sensitive help.

Defaults

When no optional parameters are specified the command shows concise information about all configured VRFs.

Command Modes

EXEC

Command History

Release	Modification
12.0(5)T	This command was introduced.

Usage Guidelines

Use this command to display information about VRFs. Two levels of detail are available: use the brief keyword or no keyword to display concise information, or use the detail keyword to display all information. To display information about all interfaces bound to a particular VRF, or to any VRF, use the interfaces keyword.

Examples

This example shows brief information for the VRFs currently configured:

Router# show ip vrf

  Name                Default RD          Interfaces

  vrf1                100:1               Ethernet1/3

  vrf2                100:2               Ethernet0/3

Table 52 describes the fields shown in this example.

Table 52 show ip vrf Field Descriptions 

Field	Description
Name	Specifies the VRF name.
Default RD	Specifies the default route distinguisher.
Interfaces	Specifies the network interfaces.

This example shows detailed information for the VRF called vrf1:

Router# show ip vrf detail vrf1

VRF vrf1; default RD 100:1

 Interfaces:

  Ethernet1/3

 Connected addresses are in global routing table

 Export VPN route-target communities

  RT:100:1

 Import VPN route-target communities

  RT:100:1

 No import route-map

Table 53 describes the significant fields shown in the output.

Table 53 show ip vrf detail Field Descriptions

Field	Description
Interfaces	Specifies the network interfaces.
Export	Specifies VPN route-target export communities.
Import	Specifies VPN route-target import communities.

This example shows the interfaces bound to a particular VRF:

Router# show ip vrf interfaces

Interface       IP-Address      VRF                       Protocol

Ethernet2       130.22.0.33     blue_vrf                  up      

Ethernet4       130.77.0.33     hub                       up      

router#

Table 54 describes the significant fields shown in the output.

Table 54 show ip vrf interfaces Field Descriptions

Field	Description
Interface	Specifies the network interfaces for a VRF.
IP-Address	Specifies the IP address of a VRF interface.
VRF	Specifies the VRF name.
Protocol	Displays the state of the protocol (up/down) for each VRF interface.

Related Commands

Command	Description
import map	Configures an import route map for a VRF.
ip vrf	Configures a VRF routing table.
ip vrf forwarding	Associates a VRF with an interface or subinterface.
rd	Creates routing and forwarding tables for a VRF.
route-target	Creates a route-target extended community for a VRF.

show isis database verbose

To display additional information about the database, use the show isis database verbose EXEC command.

show isis database verbose

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

EXEC

Command History

Release	Modification
12.0(5)S	This command was introduced.

Examples

The following is sample output from the show isis database verbose command:

Router# show isis database verbose

IS-IS Level-1 Link State Database

LSPID                 LSP Seq Num  LSP Checksum  LSP Holdtime      ATT/P/OL

dtp-5.00-00         * 0x000000E6   0xC9BB        1042              0/0/0

  Area Address:49.0001

  NLPID:       0xCC 

  Hostname:dtp-5

  Router ID:   5.5.5.5

  IP Address:  172.21.39.5

  Metric:10         IP 172.21.39.0/24

dtp-5.00-01         * 0x000000E7   0xAB36        1065              0/0/0

  Metric:10         IS-Extended dtp-5.01

    Affinity:0x00000000

    Interface IP Address:172.21.39.5

    Physical BW:10000000 bits/sec

    Reservable BW:1166000 bits/sec

    BW Unreserved[0]: 1166000 bits/sec, BW Unreserved[1]: 1166000 bits/sec

    BW Unreserved[2]: 1166000 bits/sec, BW Unreserved[3]: 1166000 bits/sec

    BW Unreserved[4]: 1166000 bits/sec, BW Unreserved[5]: 1166000 bits/sec

    BW Unreserved[6]: 1166000 bits/sec, BW Unreserved[7]: 1153000 bits/sec

  Metric:0          ES dtp-5

<