Table Of Contents

CMCC ADAPTER Messages

CMCC ADAPTER Messages

The following are Channel Interface Processor (CIP) error messages for the adapter task.

Error Message  

%ADAPTER-6-BADREQUEST : Bad request code [dec] generated on port [dec]

Explanation    A request was sent to the function that handles general requests for the specified port. The request code was not in a range recognized by that function.

Recommended Action    The CIP has recovered by ignoring the request. Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-6-BADSTATE : Bad state: port [dec], request code [dec], state [dec], flags [hex]

Explanation    The specified port was in an invalid state while it was attempting to process the specified general request.

Recommended Action    The CIP recovered by forcing the port into a valid state. Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-6-DIAGBEGIN : [chars] diagnostic starting

Explanation    The user has used the test cbus command to request a particular adapter diagnostic to be run. This message informs the user that the diagnostic routine has started.

Recommended Action    Wait for the next message.

Error Message  

%ADAPTER-0-DIAGDATA : Module Call: [hex][hex] Error ID: [hex][hex]

Explanation    A diagnostic routine has detected a failure in the ECA hardware. The indicated codes are used to locate the specific component that failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-6-DIAGDATA2 : Module Call: [hex][hex] Error ID: [hex][hex]

Explanation    A diagnostic routine has detected a failure in the ECA hardware. The indicated codes are used to locate the specific component that failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-0-DIAGFAIL : Port [dec] failed the [chars] diagnostic

Explanation    A diagnostic routine has failed. The specified port will not be used.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-6-DIAGFAIL2 : [chars] diagnostic failed

Explanation    A diagnostic requested by the test cbus command has failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-6-DIAGGOOD2 : [chars] diagnostic ran successfully

Explanation    A diagnostic requested by the test cbus command has completed successfully.

Recommended Action    No action is required.

Error Message  

%ADAPTER-6-DIAGRANGE : Diagnostic number ([dec]) out of range 0-[dec]

Explanation    The diagnostic number requested by the test cbus command is invalid.

Recommended Action    Reenter the command with a valid diagnostic number.

Error Message  

%ADAPTER-6-DIAGSTOP : Interface must be shutdown to run diagnostic

Explanation    The test cbus command was used to run a diagnostic on an active interface. The interface must be shut down before the diagnostic is run.

Recommended Action    Use the shutdown command to stop the interface and then reissue the diagnostic request.

Error Message  

%ADAPTER-0-DIAGTERM : Port [dec]: The [chars] diagnostic failed to terminate

Explanation    A diagnostic routine did not end when expected. The specified port will not be used.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-6-DIAGTERM2 : [chars] diagnostic failed to terminate

Explanation    A diagnostic requested by the test cbus command did not end when expected.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-0-LOADFAIL : Port [dec] microcode load failed.

Explanation    Each adapter has an onboard microprocessor. This message indicates that the operation to load the code for that microprocessor has failed.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-6-LOGDATA : [hex] [hex] [hex] [hex] [hex] [hex] [hex] [hex] [hex]

Explanation    An error has occurred in the adapter. The information displayed will help software developers determine the nature of the error.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-6-LOGOUT : Port [dec] logout data. Adapter microcode [hex]

Explanation    This message indicates the start of the logout data. Logout data occurs whenever a problem is detected on the port adapter or, with an ECA, on the fiber.

Recommended Action    If this message is being continually generated on a new installation, it may indicate that the fiber is not connected properly. Verify that the connector is firmly seated. If a loose fiber was not the cause of these messages, report this message to your Cisco technical support representative.

Error Message  

%ADAPTER-6-LOGSAME : [hex] to [hex] same as above

Explanation    This message is used when logout information is displayed to avoid printing duplicate data.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-6-NO_CHAN_EV_BUF : No channel event buffer: Daughter board [dec]

Explanation    Channel link incident events are being dropped by the channel adapter because of an overflow of incidents.

Recommended Action    Use SNMP to poll the CIP for the current LIR counts.

Error Message  

%ADAPTER-6-NO_CHAN_EV_POOL : Could not allocate channel event pool

Explanation    There is insufficient memory on the channel adapter to allocate buffers used for generating channel adapter events. Unless the memory is increased, no channel link incident events (SNMP traps) will be generated.

Recommended Action    Add more memory to the channel adapter.

Error Message 

%ADAPTER-6-SCAN : Port [dec] scan data. Adapter microcode [hex]

Explanation    This message precedes the "SCANDATA" error message for the adapter in the specified port. This scan is usually produced as a result of a hardware error.

Recommended Action    Report the entire error message, including the "SCANDATA" error message that follows it, to your Cisco technical support representative.

Error Message  

%ADAPTER-6-SCANDATA : [hex] [hex] [hex] [hex] [hex]

Explanation    The data in this message is related to the hardware failure of an adapter.

Recommended Action    Report the entire error message, including the preceding "SCAN" error message, to your Cisco technical support representative.

Error Message  

%ADAPTER-0-START_FAIL : Diagnostics failed for port [dec], start request ignored.

Explanation    Prior to receipt by the adapter of a start command from the Route Processor, a set of diagnostics is run. If one of them fails, then the adapter will not be started when the start command is issued.

Recommended Action    Copy the error message exactly as it appears on the console or in the system log, contact your Cisco technical support representative, and provide the representative with the gathered information.

Error Message 

%ADAPTER-6-WRAP : Wrap plug detected in port [dec]. Wrap loop started.

Explanation    A wrap plug is installed in the specified port. Wrap diagnostics will run until the wrap plug is removed, if this is the only adapter, or until both adapters have wrap plugs installed.

Recommended Action    Remove the wrap plug and connect the interface to a channel.

Error Message  

%ADAPTER-6-WRAPSTOP1 : Wrap plug removed from port [dec]. Wrap loop ended.

Explanation    The wrap plug has been removed, causing the wrap diagnostics to end.

Recommended Action    No action is required.

Error Message 

%ADAPTER-6-WRAPSTOP2 : Port [dec] active. Port [dec] wrap loop ended.

Explanation    The wrap diagnostics have ended because the other adapter is active.

Recommended Action    Remove the wrap plug and connect the interface to a channel if you wish to use this adapter. Otherwise, no action is required.