 Feedback
|
Table Of Contents
Cisco IOS Voice Features on IGX 8400 Series Universal Router Module
Supported Standards, MIBs, and RFCs
Configuring CAS Calls over VoATM Example
Configuring QSIG Calls over VoATM Example
Configuring CAS Calls Using VoIP over ATM Example
Configuring QSIG Calls Using VoIP over ATM Example
Configuring CAS Calls over VoIP Example
Configuring QSIG Calls over VoIP Example
Cisco IOS Voice Features on IGX 8400 Series Universal Router Module
Feature History
This document gives an overview the Cisco IGX 8400 Series Universal Router Module (URM) in Cisco IOS Release 12.2(8)T. Links to Cisco IOS Release 12.2 voice feature documentation and examples to configure Voice over IP (VoIP) and Voice over ATM (VoATM) are provided.
This document includes the following sections:
•
Supported Standards, MIBs, and RFCs
Feature Overview
The URM is a Cisco IOS-based IP router blade that enables users to provision Voice over IP (VoIP) and Voice over ATM (VoATM) on a Cisco IGX 8400 series platform. The voice and routing capabilities of the URM have been derived from the Cisco 3660, while the ATM capabilities have been derived from the ATM OC/3 network module for the Cisco 2600 series and Cisco 3600 series routers. The embedded UXM-E processor supports one OC3 ATM port, and the embedded router supports one OC3 ATM port similar to the 1-port OC-3/STM-1 ATM Circuit Emulation Service network module for the Cisco 3600 series routers. These ATM ports are connected to each other internally.
In addition to VoIP and VoATM, IP routing and Cisco IOS command-line interface (CLI) commands, which enable configuration of the voice ports and dial peers, are now available on the Cisco IGX 8400 series platforms.
The URM interoperates with all Cisco IOS-based voice products and supports 30 voice channels with high-complexity codec types and 60 voice channels with medium-complexity codec types. Note that only digital voice ports are supported on the URM; analog ports are not supported.
Benefits
Cisco IOS voice software on the Cisco IGX 8400 Series Universal Router Module provides the following benefits:
•
•
•
•
•
Restrictions
The following restrictions apply when configuring Cisco IOS voice software features on Cisco IGX 8400 Series Universal Router Module:
•
•
•
•
•
Related Documents
•
•
•
•
•
•
•
•
•
•
Supported Platforms
•
Determining Platform Support Through Feature Navigator
Cisco IOS software is packaged in feature sets that support specific platforms. To get updated information regarding platform support for this feature, access Feature Navigator. Feature Navigator dynamically updates the list of supported platforms as new platform support is added for the feature.
Feature Navigator is a web-based tool that enables you to quickly determine which Cisco IOS software images support a specific set of features and which features are supported in a specific Cisco IOS image.
Feature Navigator is updated regularly when major Cisco IOS software releases and technology releases occur. For the most current information, go to the Feature Navigator home page at the following URL:
Supported Standards, MIBs, and RFCs
For more information, refer to the documentation listed in the "Configuration Tasks" section.
Prerequisites
•
Configuration Tasks
Because the voice implementation on the URM has been adapted from the Cisco 3600 series routers, the IOS features supported on the Cisco IGX 8400 URM are already supported on other Cisco router models. For configuration information, see the following two manuals:
•
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fvvfax_c/index.htm
This guide provides configuration procedures for IOS voice software features. See Table 1 for information regarding specific chapters to reference.
•
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fvvfax_r/index.htm
This guide provides an alphabetical reference to voice commands used to configure voice software features.
Table 1 Chapters in Cisco IOS Voice, Video and Fax Configuration Guide, Release 12.2
Configuring Voice over IP
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fvvfax_c/vvfvoip.htm
Configuring Voice Ports for Voice over IP
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fvvfax_c/vvfport.htm
Configuring Gatekeepers (Multimedia Conference Manager)
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fvvfax_c/vvf323gk.htm
Configuring Interactive Voice Response
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fvvfax_c/vvfivr.htm
Configuring Debit Card for Packet Telephony
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fvvfax_c/vvfdebit.htm
Configuring Settlement for Packet Telephony
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fvvfax_c/vvfosp.htm
Configuration Examples
This section provides the following configuration examples:
•
•
•
•
•
•
Configuring CAS Calls over VoATM Example
The following example shows how to configure voice over ATM channel associated signaling (CAS) calls on the Cisco IGX 8400 Series Universal Router Module. Voice over ATM enables a URM to carry voice traffic (for example, telephone calls and faxes) over an ATM network by using ATM encapsulation ATM adaptation layer (AAL) 5. AAL2 is not supported.
! Configurations on URM1controller T1 2/0framing esflinecode b8zsds0-group 0 timeslots 1-24 type e&m-wink-startno shutdowninterface ATM 0/0pvc 10/61vbr-rt 1536 768 192encapsulation aal5mux voicedial-peer voice 100 potsdestination-pattern 100527....port 2/0:0dial-peer voice 120 voatmdestination-pattern 120678....session target atm0/0 pvc 10/61codec g729r8! Configurations on URM2controller T1 2/0framing esflinecode b8zsds0-group 0 timeslots 1-24 type e&m-wink-startno shutdowninterface ATM 0/0pvc 10/61vbr-rt 1536 768 192encapsulation aal5mux voicedial-peer voice 120 potsdestination-pattern 120678....port 2/0:0dial-peer voice 100 voatmdestination-pattern 100527....session target atm0/0 pvc 10/61codec g729r8Configuring QSIG Calls over VoATM Example
The following example shows how to configure VoATM QSIG calls on the Cisco IGX 8400 Series Universal Router Module:
! Configurations on URM1isdn switch-type primary-qsigcontroller T1 2/0framing esflinecode b8zspri-group timeslots 1-24no shutdowninterface ATM 0/0pvc 10/61vbr-rt 1536 768 192encapsulation aal5mux voiceinterface serial 2/0:23no ip addressisdn switch-type primary-qsigisdn incoming-voice voiceno cdp enabledial-peer voice 100 potsdestination-pattern 100527....port 2/0:0direct-inward-dialdial-peer voice 120 voatmdestination-pattern 120678....session target atm0/0 pvc 10/61codec g729r8! Configurations on URM2isdn switch-type primary-qsigcontroller T1 2/0framing esflinecode b8zspri-group timeslots 1-24no shutdowninterface ATM 0/0pvc 10/61vbr-rt 1536 768 192encapsulation aal5mux voiceinterface serial 2/0:23no ip addressisdn switch-type primary-qsigisdn incoming-voice voiceno cdp enabledial-peer voice 100 potsdestination-pattern 100678....port 2/0:0direct-inward-dialdial-peer voice 120 voatmdestination-pattern 120527....session target atm0/0 pvc 10/61codec g729r8Configuring CAS Calls Using VoIP over ATM Example
The following example shows how to configure CAS calls using VoIP over ATM on the Cisco IGX 8400 Series Universal Router Module:
! Configurations on URM1ip routingcontroller T1 2/0framing esflinecode b8zsds0-group 0 timeslots 1-24 type fxs-loop-startno shutdowninterface ATM 0/0ip address 172.16.1.1 255.0.0.0pvc 10/60cbr 1536encapsulation aal5snapprotocol ip 172.16.1.2dial-peer voice 100 potsdestination-pattern 100527....port 2/0:0dial-peer voice 120 voipdestination-pattern 120678....session target ipv4:172.16.1.2codec g729r8! Configurations on URM2ip routingcontroller T1 2/0framing esflinecode b8zsds0-group 0 timeslots 1-24 type fxs-loop-startno shutdowninterface ATM 0/0ip address 172.16.1.2 255.0.0.0pvc 10/60cbr 1536encapsulation aal5snapprotocol ip 172.16.1.1dial-peer voice 120 potsdestination-pattern 120678....port 2/0:0dial-peer voice 100 voipdestination-pattern 100527....session target ipv4:172.16.1.1codec g729r8Configuring QSIG Calls Using VoIP over ATM Example
The following example shows how to configure QSIG channel calls using VoIP over ATM on the Cisco IGX 8400 Series Universal Router Module:
! Configurations on URM1ip routingisdn switch-type primary-qsigcontroller T1 2/0framing esflinecode b8zspri-group timeslots 1-24no shutdowninterface ATM 0/0ip address 172.16.1.1 255.0.0.0pvc 10/60cbr 1536encapsulation aal5snapprotocol ip 172.16.1.2interface serial 2/0:23no ip addressisdn switch-type primary-qsigisdn incoming-voice voiceno cdp enabledial-peer voice 100 potsdestination-pattern 100527....port 2/0:0direct-inward-dialdial-peer voice 120 voipdestination-pattern 120678....session target ipv4:172.16.1.2codec g729r8! Configurations on URM2ip routingisdn switch-type primary-qsigcontroller T1 2/0framing esflinecode b8zspri-group timeslots 1-24no shutdowninterface ATM 0/0ip address 172.16.1.2 255.0.0.0pvc 10/60cbr 1536encapsulation aal5snapprotocol ip 172.16.1.1interface serial 2/0:23no ip addressisdn switch-type primary-qsigisdn incoming-voice voiceno cdp enabledial-peer voice 120 potsdestination-pattern 120678....port 2/0:0direct-inward-dialdial-peer voice 100 voipdestination-pattern 100527....session target ipv4:172.16.1.1codec g729r8Configuring CAS Calls over VoIP Example
The following example shows how to configure VoIP CAS channel calls on the Cisco IGX 8400 Series Universal Router Module:
! Configurations on URM1ip routingcontroller T1 2/0framing esflinecode b8zsds0-group 0 timeslots 1-24 type e&m-wink-startno shutdowninterface fastethernet 1/0ip address 23.0.0.1 255.0.0.0ip route-cacheno shutdowndial-peer voice 100 potsdestination-pattern 100527....port 2/0:0dial-peer voice 120 voipdestination-pattern 120678....session target ipv4:23.0.0.2codec g729r8! Configurations on URM2ip routingcontroller T1 2/0framing esflinecode b8zsds0-group 0 timeslots 1-24 type e&m-wink-startno shutdowninterface fastethernet 1/0ip address 23.0.0.2 255.0.0.0ip route-cacheno shutdowndial-peer voice 120 potsdestination-pattern 120678....port 2/0:0dial-peer voice 100 voipdestination-pattern 100527....session target ipv4:23.0.0.1codec g729r8Configuring QSIG Calls over VoIP Example
The following example shows how to configure QSIG calls using VoIP:
! Configurations on URM1ip routingisdn switch-type primary-qsigcontroller T1 2/0framing esflinecode b8zspri-group timeslots 1-24no shutdowninterface fastethernet 1/0ip address 23.0.0.1 255.0.0.0ip route-cacheno shutdowninterface serial 2/0:23no ip addressisdn switch-type primary-qsigisdn incoming-voice voiceno cdp enabledial-peer voice 100 potsdestination-pattern 100527....port 2/0:0direct-inward-dialdial-peer voice 120 voipdestination-pattern 120678....session target ipv4:23.0.0.2codec g729r8! Configurations on URM2ip routingisdn switch-type primary-qsigcontroller T1 2/0framing esflinecode b8zspri-group timeslots 1-24no shutdowninterface fastethernet 1/0ip address 23.0.0.2 255.0.0.0ip route-cacheno shutdowninterface serial 2/0:23no ip addressisdn switch-type primary-qsigisdn incoming-voice voiceno cdp enabledial-peer voice 120 potsdestination-pattern 120678....port 2/0:0direct-inward-dialdial-peer voice 100 voipdestination-pattern 100527....session target ipv4:23.0.0.1codec g729r8Command Reference
There are no new or modified commands. All Cisco IOS commands used in this feature module are documented in the Cisco IOS Release 12.2 command reference publications.
