Worldwide [change] |Account |Register |About Cisco
Guest

Hierarchical Navigation

Cisco IOS Software Releases 12.1 Special and Early Deployments

Cisco IOS Voice Features on IGX8400 Series Universal Router Module

Downloads

Table Of Contents

Cisco IOS Voice Features on IGX 8400 Series Universal Router Module

Feature Overview

Benefits

Restrictions

Related Documents

Supported Platform

Supported Standards, MIBs, and RFCs

Configuration Tasks

Additional Voice Feature Documentation

Configuration Examples

Configuring CAS Calls Over VoATM

Configuring QSIG Calls Over VoATM

Configuring CAS Calls Using VoIP Over ATM Example

Configuring QSIG Calls Using VoIP Over ATM

Configuring CAS Calls Over VoIP

Configuring QSIG Calls Over VoIP

Command Reference


Cisco IOS Voice Features on IGX 8400 Series Universal Router Module

Feature History

Release
Modification

12.1(5)YA

Support for selected Cisco IOS voice features was introduced in Cisco IGX 8400 Series Universal Router Module (URM).


This feature module provides an overview of Cisco IOS voice features supported on the Cisco IGX 8400 Series Universal Router Module (URM), Release 12.1(5)YA. This document provides links to Cisco IOS Release 12.1 voice feature documentation, and contains examples to configure Voice over IP (VoIP) and Voice over ATM (VoATM).

This document includes the following sections:

•Feature Overview

•Configuration Tasks

•Configuration Examples

Feature Overview

The URM is a Cisco IOS-based IP router blade that enables users to provision Voice over IP (VoIP) and Voice over ATM (VoATM) on a Cisco IGX 8400 series platform. The voice and routing capabilities of the URM have been derived from the Cisco 3660 series routers, while the ATM capabilities of the URM have been derived from the ATM OC/3 network module for the 2600 and 3600 Series routers. The embedded UXM-E processor supports one OC3 ATM port and the embedded router supports one OC3 ATM port similar to the 1-port OC-3/STM-1 ATM Circuit Emulation Service network module for the Cisco 3600 series routers. These ATM ports are connected to each other internally.

In addition to VoIP and VoATM, IP routing and Cisco IOS command language interface (CLI) commands—which allow configuration of the voice ports and dial peers—are now available on the Cisco IGX 8400 series platforms.

The URM interoperates with all Cisco IOS-based voice products and supports 30 voice channels with high-complexity codec types and 60 voice channels with medium-complexity codec types. Note that only digital voice ports are supported on the URM; analog ports are not supported.

Cisco IOS Release 12.1(5)YA is the first release supported on the Cisco IGX 8400 URM.

Benefits

Cisco IOS voice software on the Cisco IGX 8400 Series Universal Router Module provides the following benefits:

•High-performance, high-density, scalable, digital voice traffic on the Cisco IGX 8400 series platforms.

•The Universal Router Module (URM) delivers high-density voice interfaces, Fast Ethernet connectivity and ATM switching through a combination of Cisco IOS Release 12.1(5)YA and Switched Software (SWSW) Version 9.3 functionality.

•The URM lets you provision VoIP and VoATM using Cisco IGX 8400 series platforms. Basic routing and Cisco IOS command-language interface (CLI) commands, which allow configuration of the voice ports and dial peers, are now available on the Cisco IGX 8400 series platforms.

•The URM interoperates with all Cisco IOS-based voice products and supports 30 voice channels with high-complexity codec types and 60 voice channels with medium-complexity codec types.

•The URM supports the Cisco WAN Manager (CWM), CiscoWorks 2000, and Cisco Voice Manager (CVM)—all of which are management applications running on external stations.

Restrictions

The following restrictions apply when configuring Cisco IOS voice software features on Cisco IGX 8400 Series Universal Router Module:

•Only digital voice ports are supported on the URM. Analog ports are not supported.

•BRI interfaces are not supported.

•The slots to configure voice features are fixed. You can configure T1/E1 on slots 2/0 and 2/1, Fast Ethernet on slots 1/0 and 1/1, and ATM on slot 0/0.

•You cannot shut down the ATM port. The shutdown command is not supported.

•Voice over Frame Relay (VoFR) is not supported.

Related Documents

•Release Notes for Cisco IGX 8400 Series URM for Cisco IOS Release 12.1(5)YA

•Update to Cisco IGX 8400 Series Installation and Configuration and Reference

•Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.1

•Cisco IOS Configuration Fundamentals Command Reference, Release 12.1

•Cisco IOS Interface Configuration Guide, Release 12.1

•Cisco IOS Interface Command Reference, Release 12.1

•Cisco IOS Multiservice Applications Configuration Guide, Release 12.1

•Cisco IOS Multiservice Applications Command Reference, Release 12.1

•Online New Feature documentation for 12.1T Features (See the "Configuration Tasks" section for more information.)

Supported Platform

Cisco IGX 8400 Series Universal Router Module (URM)

Supported Standards, MIBs, and RFCs

For more information, refer to the documentation listed in the "Configuration Tasks" section.

Configuration Tasks

The IOS voice features supported on the Cisco IGX 8400 URM are already supported on other Cisco router models. The voice implementation on the URM has been adapted from the Cisco 3600 series routers. Configuration tasks for IOS voice features are described in many different documents.

For more information, see the following two manuals at the following URLs:

•Cisco IOS Multiservice Applications Configuration Guide, Release 12.1

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/multi_c/index.htm

This guide provides configuration procedures for IOS voice software features. See Table 1 for information regarding specific chapters to reference.

•Cisco IOS Multiservice Applications Command Reference, Release 12.1

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/multi_r/index.htm

This guide provides an alphabetical reference to voice commands used to configure voice software features.

Note References to analog models in the Configuring Voice over IP documentation are not applicable to the Cisco IGX 8400 Series Universal Router Module, Release 12.1(5)YA.

Table 1 Chapters to Reference in Cisco IOS Multiservice Applications Configuration Guide, Release 12.1

Chapter Title
Location on Cisco.com

Configuring Voice over IP

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/multi_c/mcprt1/mcdvoip.htm

Configuring Voice Ports for Voice over IP

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/multi_c/mcprt1/mcd5voip.htm

Configuring Gatekeepers (Multimedia Conference Manager)

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/multi_c/mcprt1/mcdmcm.htm

Configuring Interactive Voice Response

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/multi_c/mcprt1/mcd2voip.htm

Configuring Debit Card for Packet Telephony

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/multi_c/mcprt1/mcd3voip.htm

Configuring Settlement for Packet Telephony

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/multi_c/mcprt1/mcd4voip.htm


Additional Voice Feature Documentation

The Cisco IGX 8400 Series URM also supports voice features that were introduced in software versions released after Cisco IOS 12.1. These features are not included in the 12.1 IOS Multiservice Applications Configuration Guide listed above, but are described in online feature module documentation.

Note The online feature modules may supersede information contained in the Cisco IOS Multiservice Applications Configuration Guide, Release 12.1 and the Cisco IOS Multiservice Applications Command Reference, Release 12.1. Note also that these referenced documents do not list the Cisco IGX 8400 Series URM as one of the supported platforms.

Table 2, Table 3, Table 4, and Table 5 list the additional voice features introduced in releases after version 12.1 that are supported on the Cisco IGX 8400 Series URM.

Table 2 Cisco IOS Release 12.1(1)T Features Supported on the Cisco IGX 8400 URM 

Online Feature Module Document
Location on Cisco.com

Answer Supervision Reporting

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t1/asreport.htm

Asynchronous Rotary Line Queueing

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t1/dtasyncq.htm

Cisco H.323 Version 2 Phase 2

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t1/h323v2p2.htm

Configuring Redundant H.323 Zone Support

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t1/multlrq.htm

Enhancement to Cisco H.323 to Support RSVP Slow Connect

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t1/dt_rsvp.htm

Gateway-to-Gatekeeper Billing Redundancy

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t1/gwgkbill.htm

Session Initiation Protocol for Voice over IP on Cisco Access Platforms

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t1/0251clmb.htm

Settlements for Packet Voice, Phase 2

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_serv/5300/cfios/cfselfea/0123box2.htm


Table 3 Cisco IOS Release 12.1(2)T Features Supported on the Cisco IGX 8400 URM 

Online Feature Module Document
Location on Cisco.com

Configurable Timers in H.225

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t2/dtcfgtim.htm

Dial Peer Enhancements

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t2/dtdpeer.htm

Ecosystem Gatekeeper Interoperability Enhancements, Phase 2

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t2/dtgkarj.htm

FRF.12 Support on Additional Platforms1

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t2/dtfr12ap.htm

Configuring the Gatekeeper to Gatekeeper Redundancy and Load-Sharing Mechanism

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t2/dtseqlrq.htm

Configuring H.323 Support for Virtual Interfaces

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t2/dt323bnd.htm

OC-3/STM-1 ATM Circuit Emulation Service Network Module

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t2/dtoc3vpd.htm

PRI and BRI QSIG Protocol Support on Cisco 2600, 3600, and MC3810 Series Routers and PRI QSIG on the Cisco 7200

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t2/dt_qsig.htm

Voice over ATM on Cisco 3600 Series Routers

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t2/dtvoatm.htm

Voice Port Testing Enhancements in Cisco 2600 and 3600 Series Routers and MC3810 Series Concentrators

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t2/dt_tstvp.htm

1 The Cisco IGX 8400 URM does not support Voice over Frame Relay in this release. However, this feature can be used in conjunction with VoIP.


Table 4 Cisco IOS Release 12.1(3)T Features Supported on the Cisco IGX 8400 URM 

Online Feature Module Document
Location on Cisco.com

Advanced Voice Busyout

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dt_avbo.htm

Caller ID on Cisco 2600 and 3600 Series Routers and Cisco MC3810 Series Concentrators

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/clid_t4.htm

E1 R2 and Channel-Associated Signaling Configuration

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dt_r2cas.htm

Enhancements to the Session Initiation Protocol for VoIP on Cisco Access Platforms

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dtsipgv2.htm

Feature Group D Support

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dt_fgd.htm

PSTN Fallback

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dtpstnfb.htm

Q.931 User-Side and Network-Side Switch Support

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dt_q931.htm

T.38 Fax Relay for Voice over IP H.323

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dt_t38fx.htm

T1/E1 Alarm Conditioning for Switched Calls and Permanent Connection Trunks

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dtte1alm.htm

Transparent Common Channel Signaling

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dt_tccs.htm

Trunk Conditioning for FRF.11 and Cisco Trunks

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dt_tcond.htm


Table 5 Cisco IOS Release 12.1(5)T Features Supported on the Cisco IGX 8400 URM 

Online Feature Module Document
Location on Cisco.com

Interworking Signaling Enhancements for H.323 and SIP VoIP

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t5/dt4t323.htm

Multimedia Conference Manager with Voice Gateway Image with RSVP to ATM SVC Mapping

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t5/dt_mcm5t.htm

Prepaid Distributed Calling Card via Packet Telephony

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_serv/as5800/12_2t/pul0134x.htm


Configuration Examples

This section provides the following configuration examples:

•Configuring CAS Calls Over VoATM

•Configuring QSIG Calls Over VoATM

•Configuring CAS Calls Using VoIP Over ATM Example

•Configuring QSIG Calls Using VoIP Over ATM

•Configuring CAS Calls Over VoIP

•Configuring QSIG Calls Over VoIP

Note IP addresses and host names used in these examples are fictitious.

Configuring CAS Calls Over VoATM

The following example shows how to configure voice over ATM channel associated signaling (CAS) calls on the Cisco IGX 8400 Series Universal Router Module. Voice over ATM enables a URM to carry voice traffic (for example, telephone calls and faxes) over an ATM network by using ATM encapsulation ATM adaptation layer (AAL) 5. AAL2 is not supported. 


! Configurations on URM1

controller T1 2/0

  framing esf

  linecode b8zs

  ds0-group 0 timeslots 1-24 type e&m-wink-start

  no shutdown


interface ATM 0/0

  pvc 10/61

  vbr-rt 1536 768 192

  encapsulation aal5mux voice


dial-peer voice 100 pots

  destination-pattern 100527....

  port 2/0:0


dial-peer voice 120 voatm

  destination-pattern 120678....

  session target atm0/0 pvc 10/61

  codec g729r8


! Configurations on URM2


controller T1 2/0

  framing esf

  linecode b8zs

  ds0-group 0 timeslots 1-24 type e&m-wink-start

  no shutdown

interface ATM 0/0

  pvc 10/61

  vbr-rt 1536 768 192

  encapsulation aal5mux voice

dial-peer voice 120 pots

  destination-pattern 120678....

  port 2/0:0

dial-peer voice 100 voatm

  destination-pattern 100527....

  session target atm0/0 pvc 10/61

  codec g729r8

Configuring QSIG Calls Over VoATM

The following example shows how to configure VoATM QSIG calls on the Cisco IGX 8400 Series Universal Router Module. 


! Configurations on URM1


isdn switch-type primary-qsig


controller T1 2/0

  framing esf

  linecode b8zs

  pri-group timeslots 1-24

  no shutdown


interface ATM 0/0

  pvc 10/61

  vbr-rt 1536 768 192

  encapsulation aal5mux voice


interface serial 2/0:23

  no ip address

  isdn switch-type primary-qsig

  isdn incoming-voice voice

  no cdp enable


dial-peer voice 100 pots

  destination-pattern 100527....

  port 2/0:0

  direct-inward-dial


dial-peer voice 120 voatm

  destination-pattern 120678....

  session target atm0/0 pvc 10/61

  codec g729r8


! Configurations on URM2


isdn switch-type primary-qsig


controller T1 2/0

  framing esf

  linecode b8zs

  pri-group timeslots 1-24

  no shutdown

interface ATM 0/0

  pvc 10/61

  vbr-rt 1536 768 192

  encapsulation aal5mux voice

interface serial 2/0:23

  no ip address

  isdn switch-type primary-qsig

  isdn incoming-voice voice

  no cdp enable


dial-peer voice 100 pots

  destination-pattern 100678....

  port 2/0:0

  direct-inward-dial

dial-peer voice 120 voatm

  destination-pattern 120527....

  session target atm0/0 pvc 10/61

  codec g729r8

Configuring CAS Calls Using VoIP Over ATM Example

The following example shows how to configure CAS calls using VoIP over ATM on the Cisco IGX 8400 Series Universal Router Module. 


! Configurations on URM1


ip routing


controller T1 2/0

  framing esf

  linecode b8zs

  ds0-group 0 timeslots 1-24 type fxs-loop-start

  no shutdown


interface ATM 0/0

  ip address 172.16.1.1 255.0.0.0

  pvc 10/60

    cbr 1536

    encapsulation aal5snap

    protocol ip 172.16.1.2


dial-peer voice 100 pots

  destination-pattern 100527....

  port 2/0:0


dial-peer voice 120 voip

  destination-pattern 120678....

  session target ipv4:172.16.1.2

  codec g729r8


! Configurations on URM2


ip routing


controller T1 2/0

  framing esf

  linecode b8zs

  ds0-group 0 timeslots 1-24 type fxs-loop-start

  no shutdown

interface ATM 0/0

  ip address 172.16.1.2 255.0.0.0

  pvc 10/60

    cbr 1536

    encapsulation aal5snap

    protocol ip 172.16.1.1

dial-peer voice 120 pots

  destination-pattern 120678....

  port 2/0:0

dial-peer voice 100 voip

  destination-pattern 100527....

  session target ipv4:172.16.1.1

  codec g729r8

Configuring QSIG Calls Using VoIP Over ATM

The following example shows how to configure QSIG channel calls using VoIP over ATM on the Cisco IGX 8400 Series Universal Router Module. 


! Configurations on URM1


ip routing


isdn switch-type primary-qsig


controller T1 2/0

  framing esf

  linecode b8zs

  pri-group timeslots 1-24

  no shutdown


interface ATM 0/0

  ip address 172.16.1.1 255.0.0.0

  pvc 10/60

    cbr 1536

    encapsulation aal5snap

    protocol ip 172.16.1.2


interface serial 2/0:23

  no ip address

  isdn switch-type primary-qsig

  isdn incoming-voice voice

  no cdp enable


dial-peer voice 100 pots

  destination-pattern 100527....

  port 2/0:0

  direct-inward-dial


dial-peer voice 120 voip

  destination-pattern 120678....

  session target ipv4:172.16.1.2

  codec g729r8


! Configurations on URM2


ip routing

isdn switch-type primary-qsig


controller T1 2/0

  framing esf

  linecode b8zs

  pri-group timeslots 1-24

  no shutdown

interface ATM 0/0

  ip address 172.16.1.2 255.0.0.0

  pvc 10/60

    cbr 1536

    encapsulation aal5snap

    protocol ip 172.16.1.1

interface serial 2/0:23

  no ip address

  isdn switch-type primary-qsig

  isdn incoming-voice voice

  no cdp enable


dial-peer voice 120 pots

  destination-pattern 120678....

  port 2/0:0

  direct-inward-dial

dial-peer voice 100 voip

  destination-pattern 100527....

  session target ipv4:172.16.1.1

  codec g729r8

Configuring CAS Calls Over VoIP

The following example shows how to configure VoIP CAS channel calls on the Cisco IGX 8400 Series Universal Router Module. 


! Configurations on URM1


ip routing


controller T1 2/0

  framing esf

  linecode b8zs

  ds0-group 0 timeslots 1-24 type e&m-wink-start

  no shutdown


interface fastethernet 1/0

  ip address 23.0.0.1 255.0.0.0

  ip route-cache

  no shutdown


dial-peer voice 100 pots

  destination-pattern 100527....

  port 2/0:0


dial-peer voice 120 voip

  destination-pattern 120678....

  session target ipv4:23.0.0.2

  codec g729r8


! Configurations on URM2


ip routing

controller T1 2/0

  framing esf

  linecode b8zs

  ds0-group 0 timeslots 1-24 type e&m-wink-start

  no shutdown

interface fastethernet 1/0

  ip address 23.0.0.2 255.0.0.0

  ip route-cache

  no shutdown

dial-peer voice 120 pots

  destination-pattern 120678....

  port 2/0:0

dial-peer voice 100 voip

  destination-pattern 100527....

  session target ipv4:23.0.0.1

  codec g729r8

Configuring QSIG Calls Over VoIP

The following example shows how to configure QSIG calls using VoIP. 


! Configurations on URM1


ip routing


isdn switch-type primary-qsig


controller T1 2/0

  framing esf

  linecode b8zs

  pri-group timeslots 1-24

  no shutdown


interface fastethernet 1/0

  ip address 23.0.0.1 255.0.0.0

  ip route-cache

  no shutdown


interface serial 2/0:23

  no ip address

  isdn switch-type primary-qsig

  isdn incoming-voice voice

  no cdp enable


dial-peer voice 100 pots

  destination-pattern 100527....

  port 2/0:0

  direct-inward-dial


dial-peer voice 120 voip

  destination-pattern 120678....

  session target ipv4:23.0.0.2

  codec g729r8


! Configurations on URM2


ip routing

isdn switch-type primary-qsig


controller T1 2/0

  framing esf

  linecode b8zs

  pri-group timeslots 1-24

  no shutdown

interface fastethernet 1/0

  ip address 23.0.0.2 255.0.0.0

  ip route-cache

  no shutdown

interface serial 2/0:23

  no ip address

  isdn switch-type primary-qsig

  isdn incoming-voice voice

  no cdp enable


dial-peer voice 120 pots

  destination-pattern 120678....

  port 2/0:0

  direct-inward-dial

dial-peer voice 100 voip

  destination-pattern 100527....

  session target ipv4:23.0.0.1

  codec g729r8

Command Reference

There are no new or modified commands on the Cisco IGX 8400 URM. All IOS commands used on the module are documented in the Cisco IOS Release 12.1 command reference publications, and in the documents listed in the "Additional Voice Feature Documentation" section.