Worldwide [change] |Account |Register |About Cisco
Guest

Hierarchical Navigation

Cisco IOS Software Releases 12.1 E

Pre-fragmentation For Ipsec VPNs

Downloads

Table Of Contents

Pre-fragmentation For Ipsec VPNs

Feature Overview

Benefits

Restrictions

Supported Platforms

Supported Standards, MIBs, and RFCs

Configuration Tasks

Configuring Pre-fragmentation For Ipsec VPNs (optional)

Verifying Pre-fragmentation For Ipsec VPNs (optional)

Configuration Examples

Enabling Pre-fragmentation For Ipsec VPNs Example

Command Reference

crypto ipsec fragmentation


Pre-fragmentation For Ipsec VPNs

Feature History

Release
Modification

12.1(11b)E

This feature was introduced.


This document describes the pre-fragmentation for ipsec VPNs feature in Cisco IOS Release 12.1(11b)E. It includes the following sections:

•Feature Overview

•Supported Platforms

•Supported Standards, MIBs, and RFCs

•Configuration Tasks

•Configuration Examples

•Command Reference

Feature Overview

When a packet is nearly the size of the maximum transmission unit (MTU) of the outbound link of the encrypting router, and it is encapsulated with IPSec headers, it is likely to exceed the MTU of the outbound link. This causes packet fragmentation after encryption, which makes the decrypting router reassemble in the process path. Pre-fragmentation for IPSec VPNs increases the decrypting router's performance by enabling it to operate in the high performance CEF path instead of the process path.

Pre-fragmentation for IPSec VPNs enables an encrypting router to predetermine the encapsulated packet size from information available in transform sets, which are configured as part of the IPSec security association (SA). If it is predetermined that the packet will exceed the MTU of the output interface, the packet is fragmented before encryption. This avoids process level reassembly before decryption and helps improve decryption performance and overall IPSec traffic throughput.

Benefits

Increased Performance

Delivers encryption throughput at maximum encryption hardware accelerator speeds. This performance increase is for near MTU sized packets.

Uniform Fragmentation

Packets are fragmented into equally sized units to prevent further downstream fragmentation.

Interoperability

This feature is interoperable with all Cisco IOS platforms and a number of Cisco VPN clients.

Restrictions

Take the following information into consideration before this feature is configured:

•Pre-fragmentation for IPSec VPNs is on by default.

•Pre-fragmentation for IPSec VPNs operates in IPSec Tunnel mode and IPSec tunnel mode with GRE, but not with IPSec transport mode.

•Pre-fragmentation for IPSec VPNs configured on the decrypting router in a unidirectional traffic scenario does not improve the performance or change the behavior of either of the peers.

•Pre-fragmentation for IPSec VPNs occurs before the transform is applied if compression is turned on for outgoing packets.

•Pre-fragmentation for IPSec VPNs functionality depends on the egress interface crypto ipsec df-bit configuration and the incoming packet "do not fragment" (DF) bit state. See Table 1.

Table 1 Pre-fragmentation For Ipsec VPNs Dependencies 

Pre-fragmentation For Ipsec VPNs Feature State (Enabled/Disabled)
Egress Interface "crypto ipsec df-bit" Configuration
Incoming Packet DF Bit State
Result

Enabled

crypto ipsec df-bit clear

0

Fragmentation occurs before encryption.

Enabled

crypto ipsec df-bit clear

1

Fragmentation occurs before encryption.

Disabled

crypto ipsec df-bit clear

0

Fragmentation occurs after encryption and packets are reassembled before decryption.

Disabled

crypto ipsec df-bit clear

1

Fragmentation occurs after encryption and packets are reassembled before decryption.

Enabled

crypto ipsec df-bit set

0

Fragmentation occurs before encryption

Enabled

crypto ipsec df-bit set

1

Packets are dropped.

Disabled

crypto ipsec df-bit set

0

Fragmentation occurs after encryption and packets are reassembled before decryption.

Disabled

crypto ipsec df-bit set

1

Packets are dropped.

Enabled

crypto ipsec df-bit copy

0

Fragmentation occurs before encryption.

Enabled

crypto ipsec df-bit copy

1

Packets are dropped.

Disabled

crypto ipsec df-bit copy

0

Fragmentation occurs after encryption and packets are reassembled before decryption.

Disabled

crypto ipsec df-bit copy

1

Packets are dropped.


Supported Platforms

This feature runs on all platforms that support Cisco IOS Release 12.1(11b)E.

Determining Platform Support Through Cisco Feature Navigator

Cisco IOS software is packaged in feature sets that support specific platforms. To get updated information regarding platform support for this feature, access Cisco Feature Navigator. Cisco Feature Navigator dynamically updates the list of supported platforms as new platform support is added for the feature.

Cisco Feature Navigator is a web-based tool that enables you to determine which Cisco IOS software images support a specific set of features and which features are supported in a specific Cisco IOS image. You can search by feature or release. Under the release section, you can compare releases side by side to display both the features unique to each software release and the features in common.

To access Cisco Feature Navigator, you must have an account on Cisco.com. If you have forgotten or lost your account information, send a blank e-mail to cco-locksmith@cisco.com. An automatic check will verify that your e-mail address is registered with Cisco.com. If the check is successful, account details with a new random password will be e-mailed to you. Qualified users can establish an account on Cisco.com by following the directions at http://www.cisco.com/register.

Cisco Feature Navigator is updated regularly when major Cisco IOS software releases and technology releases occur. For the most current information, go to the Cisco Feature Navigator home page at the following URL:

http://www.cisco.com/go/fn

Availability of Cisco IOS Software Images

Platform support for particular Cisco IOS software releases is dependent on the availability of the software images for those platforms. Software images for some platforms may be deferred, delayed, or changed without prior notice. For updated information about platform support and availability of software images for each Cisco IOS software release, refer to the online release notes or, if supported, Cisco Feature Navigator.

Supported Standards, MIBs, and RFCs

Standards

No new or modified standards are supported by this feature.

MIBs

No new or modified MIBs are supported by this feature. To obtain lists of supported MIBs by platform and Cisco IOS release, and to download MIB modules, go to the Cisco MIB website on Cisco.com at the following URL:

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

RFCs

No new or modified RFCs are supported by this feature.

Configuration Tasks

See the following sections for configuration tasks for the pre-fragmentation for ipsec VPNs feature. Each task in the list is identified as either required or optional.

•Configuring Pre-fragmentation For Ipsec VPNs (optional)

•Verifying Pre-fragmentation For Ipsec VPNs (optional)

Configuring Pre-fragmentation For Ipsec VPNs (optional)

Pre-fragmentation for IPSec VPNs is globally enabled by default. To enable or disable pre-fragmentation for ipsec VPNs while in interface configuration mode, enter the commands in the following table. Use the commands or the no form of the commands to revert the configuration.

Note Manually enabling or disabling pre-fragmentation for ipsec VPNs will override the global configuration.

Command
Purpose

Router(config-if)# crypto ipsec fragmentation before-encryption

Enables pre-fragmentation for ipsec VPNs on the interface.

Router(config-if)# crypto ipsec fragmentation after-encryption

Disables pre-fragmentation for ipsec VPNs on the interface.

Router(config)# crypto ipsec fragmentation before-encryption

Enables pre-fragmentation for ipsec VPNs globally.

Router(config)# crypto ipsec fragmentation after-encryption

Disables pre-fragmentation for ipsec VPNs globally.


Verifying Pre-fragmentation For Ipsec VPNs (optional)

To verify that pre-fragmentation for ipsec VPNs is enabled, consult the interface statistics on the encrypting router and the decrypting router. If fragmentation occurs on the encrypting router, and no reassembly occurs on the decrypting router, fragmentation is happening before encryption, and thus the packets are not being reassembled before decryption. This means that the feature is enabled.

Note This method of verification does not apply to packets destined for the decrypting router.

Step 1 Enter the show running-configuration command on the encrypting router. If the feature is enabled, you will observe output similar to the following: 

Router# show running-configuration

crypto isakmp policy 10

 authentication pre-share

crypto isakmp key abcd123 address 25.0.0.7

!

!

crypto ipsec transform-set fooprime esp-3des esp-sha-hmac

!

crypto map bar 10 ipsec-isakmp

 set peer 25.0.0.7

 set transform-set fooprime

 match address 102

If the feature has been disabled, you will observe output similar to the following: 

Router# show running-configuration

crypto isakmp policy 10

 authentication pre-share

crypto isakmp key abcd123 address 25.0.0.7

!

!

crypto ipsec transform-set fooprime esp-3des esp-sha-hmac

crypto ipsec fragmentation after-encryption

!

crypto map bar 10 ipsec-isakmp

 set peer 25.0.0.7

 set transform-set fooprime

 match address 102

Step 2 Enter the show running-configuration interface type number command to display statistics for the encrypting router egress interface. If the feature is enabled, you will observe output similar to the following: 

Router# show running-configuration interface fastethernet 0/0

interface FastEthernet0/0

 ip address 25.0.0.6 255.0.0.0

 no ip mroute-cache

 load-interval 30

 duplex full

 speed 100

 crypto map bar

If the feature has been disabled, you will observe output similar to the following:

Router# show running-configuration interface fastethernet 0/0 

interface FastEthernet0/0

 ip address 25.0.0.6 255.0.0.0

 no ip mroute-cache

 load-interval 30

 duplex full

 speed 100

 crypto map bar

 crypto ipsec fragmentation after-encryption

Configuration Examples

This section provides the following configuration example:

•Enabling Pre-fragmentation For Ipsec VPNs Example

Enabling Pre-fragmentation For Ipsec VPNs Example

The following is a configuration example of the pre-fragmentation for ipsec VPNs feature.

Note The pre-fragmentation for ipsec VPNs feature does not show up in the running configuration in this example because the default global pre-fragmentation for ipsec VPNs feature is enabled. Pre-fragmentation for IPSec VPNs shows in the running configuration only when you explicitly enable the feature on the interface. 

crypto isakmp policy 10

 authentication pre-share

crypto isakmp key abcd123 address 25.0.0.7

!

!

crypto ipsec transform-set fooprime esp-3des esp-sha-hmac

!

crypto map bar 10 ipsec-isakmp

 set peer 25.0.0.7

 set transform-set fooprime

 match address 102

Command Reference

This section documents the new crypto ipsec fragmentation before-encryption command that configures the pre-fragmentation for ipsec VPNs feature. All other commands used with this feature are documented in the Cisco IOS Release 12.1 command reference publications.

crypto ipsec fragmentation

To enable pre-fragmentation for ipsec VPNs, use the crypto ipsec fragmentation before-encryption command. To disable pre-fragmentation for ipsec VPNs, use the crypto ipsec fragmentation after-encryption command. Use the no form of these commands to disable a manually configured command. If no other pre-fragmentation for ipsec VPNs commands are in the configuration, the router will revert to the default global pre-fragmentation for ipsec VPNs configuration.

crypto ipsec fragmentation [before-encryption | after-encryption]

no crypto ipsec fragmentation [before-encryption | after-encryption]

Syntax Description

before-encryption

Enables pre-fragmentation for ipsec VPNs.

after-encryption

Disables pre-fragmentation for ipsec VPNs.


Defaults

Pre-fragmentation for IPSec VPNs is enabled by default.

Command Modes

Interface configuration mode or global configuration mode.

Command History

Release
Modification

Cisco IOS Release 12.1(11b)E

This command was introduced.


Usage Guidelines

Use the crypto ipsec fragmentation command to enable or disable pre-fragmentation for ipsec VPNs. Pre-fragmentation for IPSec VPNs enables an encrypting router to predetermine the encapsulated packet size from information available in transform sets, which are configured as part of the IPSec security association (SA). If it is predetermined that the packet will exceed the MTU of output interface, the packet is fragmented before encryption.

Examples

The following example shows how to enable pre-fragmentation for ipsec VPNs on an interface and then how to display the output of the show running configuration command: 

Router(config-if)# crypto ipsec fragmentation before-encryption

Router(config-if)# exit

Router# show running-config

crypto isakmp policy 10

 authentication pre-share

crypto isakmp key abcd123 address 25.0.0.7

!

!

crypto ipsec transform-set fooprime esp-3des esp-sha-hmac

!

crypto map bar 10 ipsec-isakmp

 set peer 25.0.0.7

 set transform-set fooprime

 match address 102