Table Of Contents
RSVP Commands
Use the commands in this chapter to configure and monitor the Resource Reservation Protocol (RSVP), which is a signalling protocol. For RSVP configuration information and examples, refer to the "Configuring RSVP" chapter of the Network Protocols Configuration Guide, Part 1.
ip rsvp bandwidth
To enable RSVP for IP on an interface, use the ip rsvp bandwidth interface configuration command. To disable RSVP, use the no form of the command.
ip rsvp bandwidth [interface-kbps] [single-flow-kbps]
no ip rsvp bandwidth [interface-kbps] [single-flow-kbps]Syntax Description
Default
Disabled
Command Mode
Interface configuration
Usage Guidelines
This command first appeared in Cisco IOS Release 11.2.
RSVP is disabled by default to allow backward compatibility with systems that do not implement RSVP.
Example
The following example shows a T1 (1536 kbps) link configured to permit RSVP reservation of up to 1158 kbps, but no more than 100 kbps for any given flow on Ethernet 0 and serial 0 interfaces. Fair queuing is configured with 15 reservable queues to support those reserved flows, should they be required.
interface Ethernet 0ip rsvp bandwidth 1158 100interface serial 0fair-queue 64 256 15Related Commands
You can use the master indexes or search online to find documentation of related commands.
ip rsvp neighbors
ip rsvp reservation
ip rsvp sender
ip rsvp udp-multicastip rsvp neighbors
To enable neighbors to request a reservation, use the ip rsvp neighbors interface configuration command. To disable this feature, use the no form of the command.
ip rsvp neighbors access-list-number
no ip rsvp neighbors access-list-numberSyntax Description
access-list-number
Number of a standard or extended access list. It can be an integer from 1 to 199.
Default
The router accepts messages from any neighbor.
Command Mode
Interface configuration
Usage Guidelines
This command first appeared in Cisco IOS Release 11.2.
Use this command to allow only specific RSVP neighbors to make a reservation. If no limits are specified, any neighbor can request a reservation. If an access list is specified, only neighbors meeting the specified access list requirements can make a reservation.
Example
The following example allows neighbors meeting access list 1 requirements to request a reservation:
interface ethernet 0ip rsvp neighbors 1Related Commands
You can use the master indexes or search online to find documentation of related commands.
ip rsvp bandwidth
ip rsvp reservation
ip rsvp sender
ip rsvp udp-multicastip rsvp reservation
To enable a router to simulate RSVP RESV message reception from the sender, use the ip rsvp reservation interface configuration command. To disable this feature, use the no form of the command.
ip rsvp reservation session-ip-address sender-ip-address [tcp | udp | ip-protocol]
session-dport sender-sport next-hop-ip address nexthop-interface {ff | se | wf} {rate | load}
[bandwidth] [burst-size]no ip rsvp reservation session-ip-address sender-ip-address [tcp | udp | ip-protocol]
session-dport sender-sport next-hop-ip address nexthop-interface {ff | se | wf} {rate | load}
[bandwidth] [burst-size]Syntax Description
Default
The router cannot simulate receiving an RSVP RESV Message.
Command Mode
Interface configuration
Usage Guidelines
This command first appeared in Cisco IOS Release 11.2.
Use this command to force the router to act like it is receiving RSVP RESV messages from the sender.
Examples
The following example specifies the use of a Shared Explicit Filter style of reservation and the Controlled Load Service, with token buckets of 100 or 150 kbps and 60 or 65K maximum queue depth:
ip rsvp reservation 224.250.0.2 132.240.1.1 UDP 20 30 132.240.4.1 Et1 se load 100 60ip rsvp reservation 224.250.0.2 132.240.2.1 TCP 20 30 132.240.4.1 Et1 se load 150 65The following example specifies the use of a Wild Card Filter style of reservation and the Guaranteed Bit Rate Service, with token buckets of 300 or 350 kbps and 60 or 65K maximum queue depth:
ip rsvp reservation 224.250.0.3 0.0.0.0 UDP 20 0 132.240.4.1 Et1 wf rate 300 60ip rsvp reservation 224.250.0.3 0.0.0.0 UDP 20 0 132.240.4.1 Et1 wf rate 350 65Note that the Wild Card Filter does not admit the specification of the sender; it accepts all senders. This is denoted by setting the source address and port to zero. If, in any filter style, the destination port is specified to be zero, RSVP does not permit the source port to be anything else; it understands that such protocols do not use ports or that the specification applies to all ports.
Related Commands
You can use the master indexes or search online to find documentation of related commands.
ip rsvp bandwidth
ip rsvp neighbors
ip rsvp sender
ip rsvp udp-multicastip rsvp sender
To enable a router to simulate RSVP PATH message reception from the sender, use the ip rsvp sender interface configuration command. To disable this feature, use the no form of the command.
ip rsvp sender session-ip-address sender-ip-address [tcp | udp | ip-protocol] session-dport
sender-sport previous-hop-ip-address previous-hop-interface [bandwidth] [burst-size]no ip rsvp sender session-ip-address sender-ip-address [tcp | udp | ip-protocol] session-dport
sender-sport previous-hop-ip-address previous-hop-interface [bandwidth] [burst-size]Syntax Description
Default
The router cannot simulate RSVP Path message reception.
Command Mode
Interface configuration
Usage Guidelines
This command first appeared in Cisco IOS Release 11.2.
Use this command to force the router to act like it is receiving RSVP PATH messages from the sender.
Example
The following example sets up the router to act like it is receiving RSVP messages using UDP over the Loopback 1 interface.
ip rsvp sender 224.250.0.1 132.240.2.1 udp 20 30 132.240.2.1 loopback 1 50 5ip rsvp sender 224.250.0.2 132.240.2.1 udp 20 30 132.240.2.1 loopback 1 50 5ip rsvp sender 224.250.0.2 132.240.2.28 udp 20 30 132.240.2.28 loopback 1 50 5Related Commands
You can use the master indexes or search online to find documentation of related commands.
ip rsvp bandwidth
ip rsvp neighbors
ip rsvp reservation
ip rsvp udp-multicastip rsvp udp-multicast
To instruct the router to generate UDP-encapsulated RSVP multicasts whenever it generates an IP multicast, use the ip rsvp udp-multicast interface configuration command. To disable this feature, use the no form of the command.
ip rsvp udp-multicast [multicast-address]
no ip rsvp udp-multicast [multicast-address]Syntax Description
Default
The generation of UDP multicasts is disabled. If a system sends a UDP-encapsulated RSVP message to the router, the router starts using UDP for contact with the neighboring system. The router uses multicast address 224.0.0.14 and starts sending to UDP port 1699. If the command is entered without specifying a multicast address, the router uses the same multicast address.
Command Mode
Interface configuration
Usage Guidelines
This command first appeared in Cisco IOS Release 11.2.
Use this command to instruct a router to generate UDP-encapsulated RSVP multicasts whenever it generates an IP-encapsulated multicast packet. Some hosts require this trigger from the router.
Example
The following example reserves up to 7500 kbps on the Ethernet 2, with up to 1 Mbps per flow. The router is configured to use UDP encapsulation with the multicast address 224.0.0.14.
interface ethernet 2ip rsvp bandwidth 7500 1000ip rsvp udp-multicast 224.0.0.14Related Commands
You can use the master indexes or search online to find documentation of related commands.
ip rsvp bandwidth
ip rsvp neighbors
ip rsvp reservation
ip rsvp sendershow ip rsvp interface
To display RSVP-related interface information, use the show ip rsvp interface EXEC command.
show ip rsvp interface [type number]
Syntax Description
Command Mode
EXEC
Usage Guidelines
This command first appeared in Cisco IOS Release 11.2.
Use this command to show the current allocation budget and maximum allocatable bandwidth.
Sample Display
The following is sample output from the show ip rsvp interface command:
Router# show ip rsvp interfaceinterfac allocate i/f max flow max per/255 UDP IP UDP_IP UDP M/CEt1 0M 7500K 7500K 0 /255 0 0 0 0Se0 0M 1158K 1158K 0 /255 0 0 0 0Se1 30K 1158K 1158K 6 /255 0 1 0 0describes significant fields shown in the display.
show ip rsvp installed
To display RSVP-related installed filters and corresponding bandwidth information, use the show ip rsvp installed EXEC command.
show ip rsvp installed [type number]
Syntax Description
Command Mode
EXEC
Usage Guidelines
This command first appeared in Cisco IOS Release 11.2.
Use this command to show the current installed RSVP filters and the corresponding bandwidth information for a specified interface or all interfaces.
Sample Display
The following is sample output from the show ip rsvp installed command:
Router# show ip rsvp installedRSVP:RSVP: Ethernet1: has no installed reservationsRSVP: Serial0:kbps To From Protocol DPort Sport Weight Conversation0 224.250.250.1 132.240.2.28 UDP 20 30 128 270150 224.250.250.1 132.240.2.1 UDP 20 30 128 268100 224.250.250.1 132.240.1.1 UDP 20 30 128 267200 224.250.250.1 132.240.1.25 UDP 20 30 256 265200 224.250.250.2 132.240.1.25 UDP 20 30 128 2710 224.250.250.2 132.240.2.28 UDP 20 30 128 269150 224.250.250.2 132.240.2.1 UDP 20 30 128 266350 224.250.250.3 0.0.0.0 UDP 20 0 128 26describes significant fields shown in the display.
show ip rsvp neighbor
To display current RSVP neighbors, use the show ip rsvp neighbor EXEC command.
show ip rsvp neighbor [type number]
Syntax Description
Command Mode
EXEC
Usage Guidelines
This command first appeared in Cisco IOS Release 11.2.
Use this command to show the current RSVP neighbors and identify if the neighbor is using IP or UDP encapsulation for a specified interface or all interfaces.
Sample Display
The following is sample output from the show ip rsvp neighbor command:
Router# show ip rsvp neighborInterfac Neighbor EncapsulationSe1 132.240.1.49 RSVPshow ip rsvp request
To display RSVP-related request information being requested upstream, use the show ip rsvp request EXEC command.
show ip rsvp request [type number]
Syntax Description
Command Mode
EXEC
Usage Guidelines
This command first appeared in Cisco IOS Release 11.2.
Use this command to show the RSVP reservations currently being requested upstream for a specified interface or all interfaces. The received reservations may differ from requests because of aggregated or refused reservations.
Sample Display
The following is sample output from the show ip rsvp request command:
Router# show ip rsvp requestTo From Pro DPort Sport Next Hop I/F Fi Serv BPS Bytes132.240.1.49 132.240.4.53 1 0 0 132.240.3.53 Et1 FF LOAD 30K 3Kdescribes significant fields shown in the display.
show ip rsvp reservation
To display RSVP-related receiver information currently in the database, use the show ip rsvp reservation EXEC command.
show ip rsvp reservation [type number]
Syntax Description
Command Mode
EXEC
Usage Guidelines
This command first appeared in Cisco IOS Release 11.2.
Use this command to show the current receiver (RESV) information currently in the database for a specified interface or all interfaces. This information includes reservations aggregated and forwarded from other RSVP routers.
Sample Display
The following is sample output from the show ip rsvp reservation command:
Router# show ip rsvp reservationTo From Pro DPort Sport Next Hop I/F Fi Serv BPS Bytes132.240.1.49 132.240.4.53 1 0 0 132.240.1.49 Se1 FF LOAD 30K 3Kdescribes significant fields shown in the display.
show ip rsvp sender
To display RSVP-related sender information currently in the database, use the show ip rsvp sender EXEC command.
show ip rsvp sender [type number]
Syntax Description
Command Mode
EXEC
Usage Guidelines
This command first appeared in Cisco IOS Release 11.2.
Use this command to show the current RSVP sender (PATH) information currently in the database for a specified interface or all interfaces.
Sample Display
The following is sample output from the show ip rsvp sender command:
Router# show ip rsvp senderTo From Pro DPort Sport Prev Hop I/F BPS Bytes132.240.1.49 132.240.4.53 1 0 0 132.240.3.53 Et1 30K 3K132.240.2.51 132.240.5.54 1 0 0 132.240.3.54 Et1 30K 3Kdescribes the fields shown in the display.
Fixed Filter (