Table Of Contents
Network Processor Two-Port Ethernet Full-Duplex (NP-2E-FDX)
Auto-Select and Full-Duplex Example
10BaseT and Half-Duplex Example
Network Processor Two-Port Ethernet Full-Duplex (NP-2E-FDX)
Feature Summary
The Network Processor Two Port Ethernet Full-Duplex (NP-2E-FDX) is supported in the Cisco 4500 and Cisco 4700 series routers, beginning in Cisco IOS Releases 11.2(14)P and 11.3(4)T. It improves the number of applications in which the routers can be used. The feature enables the following:
•
Auto-selecting between AUI and 10BaseT interfaces
•
•
Benefits
The following are benefits of using the NP-2E-FDX:
•
•
•
Platforms
This feature is supported on these platforms:
•
•
Prerequisites
The NP-2E-FDX feature requires Cisco IOS Release 11.2(14) or later in order for the system to recognize it has a valid module. The corresponding RXBOOT image version is also required to network boot.
Supported MIBs and RFCs
There are no new MIBs or RFCs supported by this feature.
Configuration Tasks
This section describes how to enable the media type and either half-duplex or full-duplex operation.
Configuration Examples
Auto-Select and Full-Duplex Example
The following example configures auto-select and full-duplex operation:
>
>4500>
>4500>
>4500>
>4500>enable
>4500#config
>4500#configure terminal
>Enter configuration commands, one per line. End with CNTL/Z.
>4500(config)#interface ethernet 0
>4500(config-if)#media-type ?
> 10BaseT Use RJ45 connector
> AUI Use AUI connector
> auto-select Use whichever connector is attached
>
>4500(config-if)#media-type auto-select
>4500(config-if)#full-duplex
>4500(config-if)#exit
>4500(config)#exit
>4500#
>%SYS-5-CONFIG_I: Configured from console by console10BaseT and Half-Duplex Example
The following example configures 10BaseT and half-duplex operation:
>
>4500>
>4500>enable
>4500#configure terminal
>Enter configuration commands, one per line. End with CNTL/Z.
>4500(config)#interface ethernet 0
>4500(config-if)#media-type 10BaseT
>4500(config-if)#half-duplex
>4500(config-if)#exit
>4500(config)#exit
>4500#
>%SYS-5-CONFIG_I: Configured from console by consoleCommand Reference
The following lists new or modified commands for the NP-2E-FDX feature. All other commands used with this feature are documented in the Cisco IOS Release 11.3 command references.
•
•
media-type
To specify the physical connection for the configuration, use the media-type interface configuration command. Use the no form of this command to restore the default value.
media-type {10baset | AUI | auto-select}
no media-type
Syntax Description
Default
media-type auto-select.
Command Mode
Interface configuration
Usage Guidelines
This command first appeared in Cisco IOS Release 10.0.
When the NP-2E-FDX feature is installed, the default configuration is media-type auto-select. If users plan to switch interface types, auto-select is preferable because it simplifies the configuration process; users do not have to reconfigure their routers to use new ports each time.
If the user configures media-type aui, or if the user configures media-type auto-select and AUI is automatically selected, only half-duplex operation is possible; full-duplex operation is not.
Example
The following example selects auto-sensing on Ethernet interface 0:
interface ethernet 0
media-type auto-selectRelated Commands
half-duplex
full-duplex
full-duplex
To specify full-duplex mode on full-duplex single-mode and multimode port adapters, use the full-duplex command.
full-duplex
Syntax Description
This command contains no keywords or arguments.
Command Mode
Interface configuration
Usage Guidelines
This command first appeared in Cisco IOS Release 11.1.
When the NP-2E-FDX feature is installed, the default configuration is half-duplex. Full-duplex should only be configured if the interface will be connected to another port that supports full-duplex operation (for example, another NP-2E-FDX, and Ethernet switch, or Catalyst product).
If the user configures media-type aui, or if the user configures media-type auto-select and AUI is automatically selected, only half-duplex operation is possible; full-duplex operation is not. In such cases, if full-duplex operation has been enabled, it will revert to half-duplex.
Example
The following example configures full-duplex mode on the Cisco 4500:
interface ethernet 0
full-duplexRelated Commands
media-type