Release Notes IOS 11.1(19)R Feature Packs, Cisco 7000 Series [Cisco IOS Software Releases 11.1]

Table Of Contents

Release Notes for Cisco IOS Release 11.1(19)R Software Feature Packs for Cisco 7200 Series Routers

Introduction

How to Use These Release Notes

What Is a Feature Pack?

Feature Pack Components

Product Numbers Quick-Reference List

Feature Pack Overview Table

Feature Set Table

System Requirements

Memory Requirements

Hardware Supported

Software Compatibility

Determining Your Software Release

Installing Software Images Using the RSL

Recovering from a Connection Error

Restoring the Startup Configuration

Helpful Hints

Installing the Software Image Using a TFTP Server Application

Installation Process for Router Software Feature Sets

Related Documentation

Cisco 7202-Specific Documentation

New Feature Documentation

Cisco IOS Documentation Set

Documentation Modules

Master Indexes

Other Supporting Documents

Online Navigation

Service and Support

Cisco Connection Online

CD-ROM/WWW Feedback

Open Source License Acknowledgements

OpenSSL/Open SSL Project

License Issues

Release Notes for Cisco IOS Release 11.1(19)R Software Feature Packs for Cisco 7200 Series Routers

July 27, 1998

These release notes describe the Cisco IOS Release 11.1(19)R feature packs for Cisco 7200 Series routers.

Note Cisco IOS Release 11.1(19)R and the Cisco IOS Release 11.1(19)CC are the same release.

These release notes contain the following topics:

•Introduction

•System Requirements

•Installing Software Images Using the RSL

•Installing the Software Image Using a TFTP Server Application

•Related Documentation

•Service and Support

•Cisco Connection Online

•CD-ROM/WWW Feedback

•Open Source License Acknowledgements

Introduction

This section explains how to use this document, describes feature pack components, and has tables that define the aspects of a feature pack.

How to Use These Release Notes

The tables in these release notes contain details about the Cisco feature packs. Use these tables to perform the following tasks before loading a software image onto a router:

1 Use Table 1, "Feature Pack Product Numbers Quick-Reference List", to identify the software image you want to load.

2 Use Table 2, "Cisco 7200 Series Feature Packs," to identify your feature pack and the memory required for your feature set, based on the image you load.

3 Use Table 4, "Cisco 7200 Series Default Memory and Upgrade Options", to check the memory required for your feature set, and determine the factory-default memory on the router and the available memory upgrades.

4 Use the "Feature Set Table" section to identify which features are supported in a feature set image.

What Is a Feature Pack?

This section describes:

•Feature Pack Components

•Product Numbers Quick-Reference List

•Feature Pack Overview Table

•Feature Set Table

Feature Pack Components

A feature pack is a small box that contains the following items:

•CD-ROM with the following software:

•Cisco IOS feature set software images that can include bundled modem firmware

•Router Software Loader (RSL) program (a Windows 95 application)

•A Trivial File Transfer Protocol (TFTP) server application (for Windows 95 only)

•Getting Started with the Router Software Loader CD booklet

•Release notes that include alternatives to using the RSL for loading software images onto a router

•Software license for using Cisco software in-object code form on a single access server or router

•Cisco Documentation CD-ROM that contains all Cisco documentation

The heart of a feature pack is the CD-ROM that contains software images and the Router Software Loader (RSL), which is a Windows 95 application that loads an image onto an access router or server. Each feature pack CD-ROM contains at least one Cisco IOS feature set. The CD booklet, Getting Started with the Router Software Loader explains how to use the RSL to install the router image. If you cannot use the RSL to load images, you can follow the instructions in the "Installing the Software Image Using a TFTP Server Application" section.

Before running the RSL, read the section "Installing Software Images Using the RSL" on page 8.

Product Numbers Quick-Reference List

Table 1 lists the Cisco product numbers of the feature packs supported in this release.

Table 1

Product Number

Feature Pack Description

SF-G72A-11.1.x

Cisco 7200 Enterprise Feature Pack

SF-G72AN-11.1.x

Cisco 7200 Enterprise and APPN Feature Pack

SF-G72BS-11.1.x

Cisco 7200 Desktop and IBM Feature Pack

SF-G72R-11.1.x

Cisco 7200 Network Layer 3 Switching Feature Pack

Feature Pack Product Numbers Quick-Reference List

Feature Pack Overview Table

Table 2 identifies each feature pack as specified on the router software CD-ROM label, describes the feature sets in each feature pack, and lists the following: UNIX and DOS filenames of the images, memory requirements, and the RSL installer description.

Table 2 Cisco 7200 Series Feature Packs

Product Number

CD-ROM Title

Image Name (UNIX)

Image Name (DOS)

Flash Memory Required

Main Memory Required

RSL Installer Description

SF-G72A-11.1.x

Cisco 7200 Enterprise Feature Pack Release 11.1(19)R

c7200-j-mz.111-19.CC

80291419

16 MB

32 MB

Cisco 7200 Series IOS Enterprise Feature Set 11.1(19)R

SF-G72AN-11.1.x

Cisco 7200
Enterprise and APPN
Feature Pack
Release 11.1(19)R

c7200-aj-mz.111-19.CC

80291719

32 MB

32 MB

Cisco 7200 Series IOS Enterprise/APPN Feature Set 11.1(19)R

SF-G72BS-11.1x

Cisco 7200
Desktop/IBM Feature Pack
Release 11.1(19)R

c7200-dr-mz.111-19.CC

80291619

16 MB

32 MB

Cisco 7200 Series IOS Desktop/IBM Feature Set 11.1(19)R

SF-G72R-11.1x

Cisco 7200 Network Layer 3 Switching Feature Pack Release 11.1(19)R

c7200-inu-mz.111-19.CC

80203608

16 MB

32 MB

Cisco 7200 Series IOS Network Layer 3 Switching Feature Set 11.1(19)R

Feature Set Table

The Cisco IOS software is packaged into "feature sets" (also called "images"). Many different feature sets are available, and each feature set contains a specific subset of Cisco IOS features. The following conventions are used to identify feature sets:

The following list shows which feature sets are supported on the Cisco 7200 Series routers. These feature sets only apply to Cisco IOS Release 11.1(19)R.

•Enterprise

•Enterprise and APPN

•Desktop and IBM

•Network Layer 3 Switching

To determine what features are available with each feature set (software image), see Table 3. The table summarizes the features you can use when running a specific feature set on the Cisco 7200 Series routers for Cisco IOS Release 11.1(19)R. Table 3 uses these terms:

Feature Set
Matrix Term

Description

Yes

This feature is offered.

No

This feature is not offered.

Table 3 Cisco 7200 Series Software Feature Sets

Feature

Feature Set

Network Layer 3 Switching

Desktop/IBM

Enterprise

Enterprise/APPN

SNMP

Yes

Yes

Yes

Yes

RMON (events and alarms)

Yes

Yes

Yes

Yes

Asynchronous support (SLIP)

Yes

Yes

Yes

Yes

Frame Relay

—

Yes

Yes

Yes

SMDS

Yes

Yes

Yes

Yes

X.25

Yes

Yes

Yes

Yes

ISDN

—

Yes

Yes

Yes

PPP

—

Yes

Yes

Yes

HDLC

—

Yes

Yes

Yes

IP

Yes

Yes

Yes

Yes

RIP

Yes

Yes

Yes

Yes

RIPv2

Yes

Yes

Yes

Yes

IGRP

Yes

Yes

Yes

Yes

Enhanced IGRP

Yes

Yes

Yes

Yes

OSPF

Yes

Yes

Yes

Yes

BGP

Yes

Yes

Yes

Yes

EGP

Yes

Yes

Yes

Yes

PIM

Yes

Yes

Yes

Yes

NHRP

Yes

Yes

Yes

Yes

Policy-based routing

Yes

Yes

Yes

Yes

ES-IS

—

—

Yes

Yes

IS-IS

—

—

Yes

Yes

DDR

—

Yes

Yes

Yes

Snapshot routing

—

Yes

Yes

Yes

NTP

Yes

Yes

Yes

Yes

Transparent bridging

Yes

Yes

Yes

Yes

Translational bridging

Yes

Yes

Yes

Yes

Concurrent routing and bridging

Yes

Yes

Yes

Yes

Multiring

Yes

Yes

Yes

Yes

LAN extension host

Yes

Yes

Yes

Yes

ISL

Yes

—

—

—

GRE

—

Yes

Yes

Yes

IPX

Yes

Yes

Yes

Yes

NLSP

Yes

Yes

Yes

Yes

IPX RIP

Yes

Yes

Yes

Yes

RTMP

Yes

Yes

Yes

Yes

IPXWAN 2.0

—

Yes

Yes

Yes

AppleTalk Versions 1
and 2

—

Yes

Yes

Yes

AURP

Yes

Yes

Yes

Yes

SMRP

Yes

Yes

Yes

Yes

SRTP

—

—

Yes

Yes

DECnet IV

—

Yes

Yes

Yes

DECnet V

—

—

Yes

Yes

OSI

—

—

Yes

Yes

Apollo Domain

—

—

Yes

Yes

Banyan VINES

—

—

Yes

Yes

ISO CLNS

—

—

Yes

Yes

XNS

—

—

Yes

Yes

Lock-and-Key

Yes

Yes

Yes

Yes

MD5 routing authentication

Yes

Yes

Yes

Yes

Kerberized login

—

—

Yes

Yes

TACACS+

Yes

Yes

Yes

Yes

RADIUS

Yes

Yes

Yes

Yes

V.120

—

—

Yes

Yes

SRB^¹

—

Yes

Yes

Yes

RSRB

—

Yes

Yes

Yes

APPN

—

—

—

Yes

FRAS BAN

—

Yes

Yes

Yes

DLSw (RFC 1795)

—

Yes

Yes

Yes

DLSw+^²

—

Yes

Yes

Yes

SDLC

—

Yes

Yes

Yes

SDLLC

—

Yes

Yes

Yes

SRT bridging

—

Yes

Yes

Yes

STUN

—

Yes

Yes

Yes

TG/COS

—

—

Yes

Yes

QLLC

—

Yes

Yes

Yes

DSPU

—

—

Yes

Yes

NetView Native Service Point

—

Yes

Yes

Yes

Protocol translation

—

—

Yes

Yes

Telnet

Yes

Yes

Yes

Yes

Modem auto-configuring

Yes

Yes

Yes

Yes

PAD

—

—

Yes

Yes

AutoInstall

Yes

Yes

Yes

Yes

Router monitoring

—

—

Yes

Yes

DHCP

—

—

Yes

Yes

NetBEUI over PPP

—

—

Yes

Yes

¹SRB over FDDI is not supported in this release.

²DLSw+ over TCP/IP is supported.

System Requirements

This section describes the following:

•Memory Requirements

•Hardware Supported

•Software Compatibility

•Determining Your Software Release

Memory Requirements

Table 4 lists the memory delivered by default and the available memory upgrades.

Depending on the circumstances, you might need to determine the amount of main memory (DRAM) required by your Cisco 7200 series router to support a combination of installed port adapter types and the Cisco IOS image you intend to load from the feature pack CD-ROM. To calculate memory requirements, use the publication Cisco 7200 Series Port Adapter Hardware Configuration Guidelines (78-3471-xx), which ships with your chassis.

Table 4

Memory Type

Cisco 7200 Series Defaults

Upgrade Options

Flash memory card

16 MB

20-MB upgrade for Cisco 7202: MEM-I/O-7202-20M

8-MB upgrade: MEM-I/O-FLC8M=
16-MB upgrade: MEM-I/O-FLC16M=
20-MB upgrade: MEM-I/O-FLC20M=

DRAM

32 MB

8-MB upgrade: MEM-NPE-8MB=
16-MB upgrade: MEM-NPE-16MB=
32-MB upgrade: MEM-NPE-32MB=
64-MB upgrade: MEM-NPE-64MB=
183-MB upgrade: MEM-NPE-128MB=

Cisco 7200 Series Default Memory and Upgrade Options

Hardware Supported

The Router Software Loader (RSL) Version 7.1 supports many Cisco series of routers. Specific to the Cisco 7200 series, the RSL Version 7.1 supports the Cisco 7202, Cisco 7204, and Cisco 7206).

Software Compatibility

The feature packs described in these release notes contain Cisco IOS Release 11.1(19)R software images, some earlier images, and the Router Software Loader (RSL) Version 7.1. Before running the RSL, read the "Installing Software Images Using the RSL" section.

Determining Your Software Release

To view the version of Cisco IOS software that is running on your Cisco 7200 series router, log in to the router, and enter the show version user EXEC command:
router> show version
An output begins similar to the following. The Cisco IOS version appears in the second line.
Cisco Internetwork Operating System Software 
IOS (tm) 7200 Software (C7200-BNR2SY-L), Version 11.1(19)R, RELEASE SOFTWARE
The output includes more information including processor revision numbers, memory amounts, hardware IDs, and partition information.

Installing Software Images Using the RSL

The Router Software Loader (RSL) application contained on the feature pack CD-ROM is designed to work with a PC running Microsoft Windows 95. Refer to the booklet included with the CD-ROM for instructions to install the software images.

This section describes several solutions to problems you might encounter when using the RSL. These solutions are additions to the RSL online help.

Recovering from a Connection Error

This installation tip provides a possible recovery solution in the event that you are unable to connect to your router. You can skip this section unless you are experiencing a connection error.

In some cases, you might receive the following error message while connecting to the target router:
"Failed to configure the router to enable the Cisco IOS software image and 
configuration file upload and download operations. You may want to check the router to 
make sure that the selected interface exists."
If you encounter this message, try increasing the Short Timeout value, which is set to 25 seconds, in the Options dialog box, especially if one of the following situations applies:

Note   Increasing the Short Timeout value might increase the time it takes for the RSL to connect to the target router.

•You are connecting to a router that has a large configuration file.

•You are connecting to a Cisco AS5200 access server. A Cisco AS5200 requires up to 45 seconds to write a configuration to nonvolatile random-access memory (NVRAM), because of the amount of interfaces that must be checked during this process. Increase the Short Timeout value to 60 seconds.

Restoring the Startup Configuration

In some cases, the RSL is unable to restore the startup configuration. If this happens, take the following steps:

Step 1 Ensure that all cables are properly attached to both the router and the PC.

Step 2 Restart the RSL, and connect using the Preconfigured router option.

Step 3 When asked if you want to overwrite the existing startup configuration file, choose No.

Step 4 When asked if you want to continue, choose Yes.

Step 5 When connected, select Download Router Configuration in the Router Software Loader dialog box.

Step 6 Select the appropriate file, and click Copy configuration to the router's nonvolatile memory.

The router should now contain the startup configuration it had before the initial RSL connection. You can now exit the RSL.

Note   In the previous situation, the router's configuration register (config-register 0xnnnn) is not restored.

Note   If you enter Ctrl-Alt-Delete to terminate the RSL, the router's configuration and configuration register are not restored. However, in this case, the configuration file is not deleted from the PC, so it can be restored using the previous steps.

Helpful Hints

The following information about RSL operations can help you with the installation process:

•If you have added any static entries to the PC's Address Resolution Protocol (ARP) table, one of them might be deleted by the RSL. This entry will need to be manually reentered into the PC's ARP table.

•If the router's running configuration at connection time is not the same as the router's startup configuration, the exact configuration will not be restored. Any changes that you have made since the last time a copy running-config startup-config or write memory command was entered will be lost.

•RSL will restore the router's running configuration, but some configuration commands will not be restored. However, the startup configuration will be correct. You can restore the exact running configuration by rebooting the router. Commands not restored to the running configuration include the following interface configuration commands: no shutdown, no ringspeed, and media-type aui.

Installing the Software Image Using a TFTP Server Application

The Router Software Loader (RSL) application contained on the feature pack CD-ROM is designed to work with a PC running Microsoft Windows 95. The booklet included with the CD-ROM explains how to perform this simple and recommended install process. However, an alternative is available using a TFTP server application to install router software.

This section explains how to use a TFTP server application as an alternative to using the RSL to install the router software from the CD-ROM. You can perform this procedure using a PC (running Microsoft Windows 95 or Microsoft Windows 3.1), a Macintosh, or a UNIX system. You can use either the copy tftp flash or copy rcp flash command to download the software to the router.

First obtain a TFTP application or a remote copy protocol (rcp) application to set up your computer as a TFTP server or an rcp server. You can use the RSL or the TFTP server included on the feature pack CD-ROM to install the software only if you are using a PC running Windows 95. For other operating systems, a number of TFTP or rcp applications are available from independent software vendors or as shareware from public sources on the World Wide Web.

Installation Process for Router Software Feature Sets

This section provides steps that describe how to install the router software feature sets using a Microsoft Windows 3.1 PC with a TFTP server application. You can also set up your Macintosh or UNIX workstation as a TFTP server and follow the same steps.

To install the software using an rcp application, follow the same procedure and substitute rcp for TFTP in the instructions. You must also substitute the copy rcp flash command for the copy tftp flash command in Step 8.

Step 1 Install any TFTP application on the PC. (Not provided by Cisco.)

Step 2 Launch the TFTP application on the PC. You commonly do this by double-clicking the application icon or its filename.

Step 3 Set up the PC as a TFTP server using the TFTP application setup or configuration facility.

The user interface of most TFTP applications includes a setup facility that allows you to specify the PC as a server. For example, from the TFTP menu of one application, you can select Settings to display a panel that includes a checkbox beside the word Server. To configure the local PC as a server, click in this checkbox.

The TFTP server also allows you to select a "root" directory. You must select the directory in which the Cisco IOS and upgrade files reside, for example d:\cpswinst\images.

Caution

Be sure you set up your local PC as a TFTP server. If you overlook this step, you will not be able to perform the copy procedure. This reminder also applies if you are using rcp on your system instead of TFTP.

Step 4 Establish a console session from your local PC (which is now configured as a TFTP server) to the Cisco router.

You can do this in two ways:

•Connect the PC's COM port to the router's console port.

This is the recommended method. If you use this method, when you reload the router to cause the image to take effect in Step 10, you will remain connected to the router. (Using Telnet, you will lose connection to the router at that point in the process.)

• Establish a Telnet session from the PC to the router.

Step 5 Connect your PC's Ethernet, Fast Ethernet, or Token Ring port to the router's corresponding LAN port. Use the 10BaseT crossover cable provided if connecting to an Ethernet or Fast Ethernet port. You must use Category 5 cable for Fast Ethernet routers.

Note   Use straight-through cables if you are connecting through a 10BaseT hub or a 100BaseT hub.

For systems without a LAN interface, make sure that the router and the PC have IP connectivity through the available interface (that is, the router and PC can ping each other with IP traffic).

Step 6 At the router prompt, enter the enable mode and supply the necessary password if prompted:
Router> enable
password: password
router#
Caution

Be aware that a Cisco 7200 series router do not prompt you before it erases the Flash memory card. Also, it will load the Cisco IOS image even if it doesn't fit. For this reason, Cisco Systems recommends that you issue the delete and squeeze commands before copying the new software image to Flash memory.

Step 7 Delete and then squeeze the contents of Flash memory, as shown below.
Router# show flash slot0:
-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name
1   .. unknown  0CC88032  318F74   12  3116788 Mar 26 1998 08:07:07 80203408.bin
4878476 bytes available (3116916 bytes used)
Router# show flash slot1:
-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name
1   .. unknown  48FFB8AE  2E4470   12  2900976 Mar 26 1998 07:50:41 80126717.bin
5094288 bytes available (2901104 bytes used)
Router# show flash bootflash:
-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name
1   .. unknown  06169C50  1D8CAC   21  1674284 Mar 16 1998 17:03:16
c7200-boot-mz.113-2.2
2   .. unknown  780E0F80  3491B4   23  1508488 Mar 16 1998 17:04:02
c7200-boot-mz.111-19.CC
224844 bytes available (3183028 bytes used)
Router#
Router# delete slot0:80203408.bin
Overwrite image file? [confirm]
Router# sh flash slot0:
-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name
1   .D unknown  0CC88032  318F74   12  3116788 Mar 26 1998 08:07:07 80203408.bin
4878476 bytes available (3116916 bytes used)
Router# squeeze slot0:
All deleted files will be removed, proceed? [confirm]
Squeeze operation may take a while, proceed? [confirm]
Erasing squeeze log
Router# 
Step 8 At the router prompt, enter the following command to copy the new software image from the CD-ROM drive of the PC to the Cisco 7200 series router. In this example, the filename 80203408.bin is the name of the file on the CD-ROM. The filename c7200-aj-mz.111-19.cc is the destination name for the IOS image to be copied to the router.
Router# copy tftp:80203408.bin slot0:c7200-ajs-mz.111-19.cc
7995264 bytes available on device slot0, proceed? [confirm] 
Step 9 When prompted, enter the IP address of your local Microsoft Windows 3.1-based PC, as in the following example. This is the IP address of your local PC, not that of the router.
Address or name of remote host [255.255.255.255]? 131.108.1.1
Accessing file "c7200-aj-mz.111-19.c" on 171.69.92.82 ...FOUND
Loading c7200-aj-mz.111-19.cc from 171.69.92.82 (via Ethernet1/1):
!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!
[OK - 2958932/5917696 bytes]
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCC
The entire copying process takes several minutes and differs from network to network. During the transfer process, the software displays messages indicating that it has accessed the file you have specified and is loading it.

The exclamation point (!) indicates that the copy process is taking place. Each exclamation point (!) indicates that ten packets have been transferred successfully. A checksum verification of the image occurs after the image is written to Flash memory.

After the load process completes, the router verifies that the transfer was successful and displays a series of Cs on the console.

Step 10 Enter the reload command to reload the router:
Router# reload
Note   You do not need to save the system configuration when prompted here. After the reload is complete, the router should be running the required Cisco IOS image. Use the show version command to verify that you have the correct image.

Related Documentation

These release notes should be used in conjunction with the documents listed in this section:

•Cisco 7202-Specific Documentation

•New Feature Documentation

•Cisco IOS Documentation Set

•Other Supporting Documents

•Online Navigation

The documents listed in this section are available in printed or electronic format. See the section "Online Navigation" on page 15 for more information on accessing electronic documentation.

Cisco 7202-Specific Documentation

The following documents are specific to the Cisco 7202 routers:

•Cisco 7202 Installation and Configuration Guide

•Cisco 7202 Configuration Notes

•Regulatory Compliance and Safety Information for the Cisco 7200 Series Routers

New Feature Documentation

New feature documentation is first published online only, and is eventually added to the books in the Cisco IOS documentation set. New feature documentation includes configuration tasks and new and changed command reference information; it supplements the Cisco IOS Release 11.1 configuration guide and command reference books. The new feature documentation for Release 11.1 CC is available online on CCO and on the Documentation CD-ROM. Refer to the "Online Navigation" on page 15 for details.

Cisco IOS Documentation Set

The Cisco IOS software documentation is divided into nine modules and two master indexes. There are also four supporting documents.

Note   The most current Cisco IOS documentation can be found on the latest Documentation CD-ROM and on the Web. These electronic documents contain updates and modifications made after the paper documents were printed. See the section "Online Navigation" for details.

Documentation Modules

Each module consists of two books: a configuration guide and a corresponding command reference. Chapters in a configuration guide describe protocols, configuration tasks, and Cisco IOS software functionality and contain comprehensive configuration examples. Chapters in a command reference provide complete command syntax information. Each configuration guide can be used in conjunction with its corresponding command reference.

Master Indexes

Two master indexes provide indexing information for the Cisco IOS software documentation set: an index for the configuration guides and an index for the command references. In addition, individual books contain a book-specific index.

The Cisco IOS documentation set consists of the following books and chapter topics:

Books

Chapter Topics

•Configuration Fundamentals Configuration Guide

•Configuration Fundamentals Command Reference

Configuration Fundamentals Overview

Cisco IOS User Interfaces

File Management

Interface Configuration

System Management

•Network Protocols Configuration Guide, Part 1

•Network Protocols Command Reference, Part 1

IP Addressing

IP Services

IP Routing Protocols

•Network Protocols Configuration Guide, Part 2

•Network Protocols Command Reference, Part 2

AppleTalk

Novell IPX

•Network Protocols Configuration Guide, Part 3

•Network Protocols Command Reference, Part 3

Apollo Domain

Banyan VINES

DECnet

ISO CLNS

XNS

•Wide-Area Networking Configuration Guide

•Wide-Area Networking Command Reference

ATM

Frame Relay

SMDS

X.25 and LAPB

•Security Configuration Guide

•Security Command Reference

AAA Security Services

Security Server Protocols

Traffic Filtering

Network Data Encryption

Passwords and Privileges

Neighbor Router Authentication

IP Security Options

•Dial Solutions Configuration Guide

•Dial Solutions Command Reference

Dial Business Solutions and Examples

Dial-In Port Setup

DDR and Dial Backup

Remote Node and Terminal Service

Cost-Control and Large-Scale Dial Solutions

VPDN

•Cisco IOS Switching Services Configuration Guide

•Cisco IOS Switching Services Command Reference

Switching Paths for IP Networks

Fast Switching

Autonomous Switching

NetFlow Switching

Optimum Switching

Virtual LAN (VLAN) Switching and Routing

Inter-Switch Link Protocol Encapsulation

IEEE 802.10 Encapsulation

LAN Emulation

•Bridging and IBM Networking Configuration Guide

•Bridging and IBM Networking Command Reference

Transparent Bridging

Source-Route Bridging

Remote Source-Route Bridging

DLSw+

STUN and BSTUN

LLC2 and SDLC

IBM Network Media Translation

DSPU and SNA Service Point

SNA Frame Relay Access Support

APPN

NCIA Client/Server Topologies

IBM Channel Attach

•Cisco IOS Software Command Summary

•Dial Solutions Quick Configuration Guide

•System Error Messages

•Debug Command Reference

Note   The Cisco Management Information Base (MIB) User Quick Reference publication is no longer being published. For the latest list of MIBs supported by Cisco, see the Cisco Network Management Toolkit on Cisco Connection Online. On CCO, go to Software and Support: Software Center: Network Management Products: Cisco Network Management Toolkit: Cisco MIBs.

Other Supporting Documents

The following documents also relate to the Cisco 7200 series routers:

•Release Notes for Cisco IOS Release 11.1

•Product-specific Cisco IOS release notes for the Cisco 7200 series routers

•Cisco IOS Software Release 11.1 and 11.1 CA Caveats

Online Navigation

The Cisco IOS software documentation set is available as printed manuals or electronic documents. You can access Cisco documentation at Cisco Connection Online (CCO) on the World Wide Web and on the Cisco Documentation CD-ROM:

•Cisco 7200 series manuals and configuration notes:

•Using a web browser, go to http://www.cisco.com/, click Products & Ordering, select Cisco Documentation, go to Access Servers and Access Routers, select Core/High-End Routers, and click Cisco 7200 Series Routers.

•On the Documentation CD-ROM, go to Cisco Product Documentation, select Access Servers and Access Routers, go to Core/High-End Routers, and click Cisco 7200 Series Routers.

•Cisco IOS documentation set and supporting documents:

•On Cisco Connection Online (CCO), the path is Products and Ordering: Documentation: Cisco Documentation: Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 11.1.

•On the Documentation CD, the path is Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 11.1.

•New feature documentation for Cisco IOS 11.1 CC features:

•On Cisco Connection Online (CCO), the path is Products and Ordering: Documentation: Cisco Documentation: Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 11.1: Cisco IOS 11.1 CC New Features.

•On the Documentation CD, the path is Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 11.1: Cisco IOS 11.1 CC New Features.

For additional information about the Documentation CD-ROM and CCO, refer to the sections "Cisco Connection Online" and "CD-ROM/WWW Feedback" at the end of these release notes.

Service and Support

The following URL contains links to access helpful tips on configuring your Cisco products:
http://www.cisco.com/public/serv_tips.shtml
This URL is subject to change without notice. If it changes, point your web browser to http://www.cisco.com/, and follow this path: Software & Support, Technical Tips (button on left margin).

"Hot Tips" are popular tips and hints gathered from the Cisco Technical Assistance Center (TAC). Most of these documents are available from the TAC FAX-on-demand service. To access FAX-on-demand and receive documents at your FAX machine, from the USA, call 888-50-CISCO (888-502-4726). From other areas, call 415-596-4408.

The following sections are provided from the Technical Tips page:

•Field Notices—Designed to provide notification of any critical issues regarding Cisco products. These include problem descriptions, safety or security issues, and hardware defects.

•Hardware—Technical Tips related to specific hardware platforms.

•Internetworking Features—Tips on using and deploying Cisco IOS software features and services.

•Sample Configurations—Actual configuration examples complete with topology and annotations.

•Software Products—MultiNet and Cisco Suite 100, Network Management, Cisco IOS Software Bulletins, and CiscoPro Configurations.

•Special Collections—Other Helpful Documents, Frequently Asked Questions, Security Advisories, References and RFCs, Case Studies, and the CiscoPro Documentation CD-ROM.

Cisco Connection Online

Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.

Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.

CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.

You can access CCO in the following ways:

•WWW:  http://www.cisco.com

•WWW:  http://www-europe.cisco.com

•WWW:  http://www-china.cisco.com

•Telnet:  cco.cisco.com

•Modem:  From North America, 408 526-8070; from Europe, 33 1 64 46 40 82. Use the following terminal settings: VT100 emulation; databits: 8; parity: none; stop bits: 1; and connection rates up to 28.8 kbps.

For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.

Note   If you are a network administrator and need personal technical assistance with a Cisco product that is under warranty or covered by a maintenance contract, contact Cisco's Technical Assistance Center (TAC) at 800 553-2447, 408 526-7209, or tac@cisco.com. To obtain general information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or cs-rep@cisco.com.

CD-ROM/WWW Feedback

Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.

If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.

Open Source License Acknowledgements

The following notices pertain to this software license.

OpenSSL/Open SSL Project

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/).

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com).

This product includes software written by Tim Hudson (tjh@cryptsoft.com).

License Issues

The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact openssl-core@openssl.org.

OpenSSL License:

Copyright © 1998-2007 The OpenSSL Project. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions, and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)".

4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl.org.

5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment:

"This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)".

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS"' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).

Original SSLeay License:

Copyright © 1995-1998 Eric Young (eay@cryptsoft.com). All rights reserved.

This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).

The implementation was written so as to conform with Netscapes SSL.

This library is free for commercial and non-commercial use as long as the following conditions are adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com).

Copyright remains Eric Young's, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following acknowledgement:

"This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)".

The word `cryptographic' can be left out if the routines from the library being used are not cryptography-related.

4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: "This product includes software written by Tim Hudson (tjh@cryptsoft.com)".

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The license and distribution terms for any publicly available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution license [including the GNU Public License].

78-5553-01

Cisco IOS Software Releases 11.1

Release Notes IOS 11.1(19)R Feature Packs, Cisco 7000 Series

Hierarchical Navigation

Downloads

Table Of Contents

Release Notes for Cisco IOS Release 11.1(19)R Software Feature Packs for Cisco 7200 Series Routers

Introduction

How to Use These Release Notes

What Is a Feature Pack?

Feature Pack Components

Product Numbers Quick-Reference List

Feature Pack Overview Table

Feature Set Table

System Requirements

Memory Requirements

Hardware Supported

Software Compatibility

Determining Your Software Release

Installing Software Images Using the RSL

Recovering from a Connection Error

Restoring the Startup Configuration

Helpful Hints

Installing the Software Image Using a TFTP Server Application

Installation Process for Router Software Feature Sets

Related Documentation

Cisco 7202-Specific Documentation

New Feature Documentation

Cisco IOS Documentation Set

Documentation Modules

Master Indexes

Other Supporting Documents

Online Navigation

Service and Support

Cisco Connection Online

CD-ROM/WWW Feedback

Open Source License Acknowledgements

OpenSSL/Open SSL Project

License Issues

Technology Trends