Table Of Contents
Configuring Modem Support and Chat Scripts
Configuring the Access Server
Bitrate Maximums for Cisco Devices
Configuring the Modem
Configuring Reverse Connection
Attaching to the Modem
Example String
Modem Settings for Use in Strings
Troubleshooting Tips
Configuring Modem Support and Chat Scripts
This chapter contains information to help you to configure most popular modems to work with Cisco access servers or with the console and/or auxuillary port of Cisco access servers and routers.
Configuring the Access Server
The following line configuration is recommended in most situations:
line x
|
The tty line number. The AUX port is 1 on routers, last_tty+1 on access servers.
|
speed 38400
|
The speed to use on this line. Set to highest speed in common between modem + port.
|
flow hard
|
RTS/CTS flowcontrol. Set only the CTS on ASMs.
|
modem inout
|
Drop connection on loss of CD, Cycle DTR for connection close
|
The above configuration assumes the following:
•
That the modem will always communicate to the access server or router at "speed" (which is why you must LOCK SPEED on the modem).
•That the "CD" lead of the modem reflects the real state of the carrier, and that the modem will hang up when a Cisco device drops DTR.
Note If possible, try to avoid using autobaud. You may experience problems with the router or access server if you use it.
Bitrate Maximums for Cisco Devices
Bitrate information for Cisco devices is as follows:
•57600 is the maximum speed for ASM, STS-10, and AUX ports
•115200 is the maximum speed for the 25xx access servers
If flowcontrol is not available on your modem, use 9600 baud as the maximum speed.
Note If you are routing over the AUX port, each character generates a processor interrupt. Abnormally high CPU can be resolved by using a lower AUX port speed.
Configuring the Modem
You must issue commands to the modem starting with "AT" and issue them at the speed at which you wish the modem to communicate to the access server or router. This insures that the modem will always communicate to the access server or router at that speed regardless of the speed of any incoming modem connection. This also assumes that you set the modem to lock on the DTE speed, which is required.
Configuring Reverse Connection
If possible, configure modems using reverse connection. To make a reverse connection, issue this Telnet command from anywhere on the network that can ping x.x.x.x:
where x.x.x.x is any active, connected, and up interface on the Cisco device and yy is the line number to which you want to connect.
Note The router AUX port is 01. The AUX port on an access server is the last_tty+1, e.g. on a 16-port access server, the AUX port is port 17.
If you get a connection refused message, refer to the section "Troubleshooting Tips" for a likely cause and resolution.
Attaching to the Modem
Take the following steps to attach to the modem:
Step 1 Attach to the modem using the same speed at which the Cisco access server or router port will be set, as described in "Configuring Reverse Connection." This ensures that you are at the same line speed as the Cisco access server or router.
Step 2 Issue an AT command built by using information appropriate for your modem as listed in .
Start with commands listed as required for all modems and then add the EC/Compression pair (either "BEST," or "NO") that best suits your need. This is the minimum that you need to start. For applications that are primarily file transfer, the "BEST" pair is advised. For connections that are primarily ARA, Xremote, or interactive packet-protocol (SLIP/PPP) traffic, the "NO" pair is advised.
Step 3 If you have an AUX port (or no modem control), add commands listed under Settings for Use with AUX Port in . Remember to limit to 9600 bps if you have no flow control.
Step 4 Add commands listed under the heading Platform Specific Settings in for ASM platforms.
Step 5 End the string with a &W.
Example String
A Microcom with best error correction/compression with an ASM would be:
AT&FS0=1&C1&D3\Q3\J0\N6%C1\Q2&W
Modem Settings for Use in Strings
contains required settings and EC/compression settings for specific modem types. Use this information to create your modem scripts. contains information for setting AUX ports, for configuring ASMs, and general comments. Refer to for a legend of symbols used in these two tables.
Table B-1
Settings Required for All Modems
|
Settings for EC/Compression
|
Modem
|
FD
|
AA
|
CD
|
DTR
|
RTS/CTS Flow
|
LOCK DTE Speed
|
Best Error
|
Best Comp
|
No Error
|
No Comp
|
Codex 3260
|
&F
|
S0=1
|
&C1
|
&D3
|
*FL3
|
*SC1
|
*SM3
|
*DC1
|
*SM1
|
*DC0
|
USR Courier
USR Sportster
|
&F
|
S0=1
|
&C1
|
&D3
|
&H1&R2
|
&B1
|
&M4
|
&K1
|
&M0
|
&K0
|
Global Village
Teleport Gold
|
&F
|
S0=1
|
&C1
|
&D3
|
\Q3
|
\J0
|
\N7
|
%C1
|
\N0
|
%C0
|
Telebit
T1600/T3000/WB
|
&F1
|
S0=1
|
&C1
|
&D3
|
S58=2
S68=2
|
S51=6
|
S180=2
S181=1
|
S190=1
|
S180=0
S181=1
|
S190=0
|
Telebit
T2500 (ECM)
|
&F
|
S0=1
|
&C1
|
&D3
|
S58=2
S68=2
|
S51=6
|
S95=2
|
S98=1
S96=1
|
S95=0
|
S98=0
S96=0
|
Telebit
Trailblazer
|
&F
|
S0=1
|
&C1
|
|
|
|
|
|
|
|
AT&T Paradyne Dataport
|
&F
|
S0=1
|
&C1
|
&D3
|
\Q3
|
--->
|
\N7
|
%C1
|
\N0
|
%C0
|
Hayes modems Accura/
Optima
|
&F
|
S0=1
|
&C1
|
&D3
|
&K3
|
&Q6
|
&Q5
|
&Q9
|
&Q6
|
<---
|
Microcom
QX4232 series
|
&F
|
S0=1
|
&C1
|
&D3
|
\Q3
|
\J0
|
\N6
|
%C1
|
\N0
|
%C0
|
Motorola UDS
FastTalk II
|
&F
|
S0=1
|
&C1
|
&D3
|
\Q3
|
\J0
|
\N6
|
%C1
|
\N0
|
%C0
|
Multitech
MT1432 MT932
|
&F
|
S0=1
|
&C1
|
&D3
|
&E4
|
$BA0
|
&E1
|
&E15
|
&E0
|
&E14
|
Digicom
Scout Plus
|
&F
|
S0=1
|
&C1
|
&D3
|
*F3
|
*S1
|
*E9
|
<---
|
*E0
|
<---
|
Digicom
SoftModem
|
&F
|
S0=1
|
&C1
|
&D3
|
&K3
|
--->
|
\N5
|
%C1
|
\N0
|
%C0
|
Viva
14.4/9642c
|
&F
|
S0=1
|
&C1
|
&D3
|
&K3
|
--->
|
\N3
|
%M3
|
\N0
|
%M0
|
ZyXel
U-1496E
|
&F
|
S0=1
|
&C1
|
&D3
|
&H3
|
&B1
|
&K4
|
<---
|
&K0
|
<---
|
Supra
V.32bis/28.8
|
&F
|
S0=1
|
&C1
|
&D3
|
&K3
|
--->
|
\N3
|
%C1
|
\N0
|
%C0
|
ZOOM
14.4
|
&F
|
S0=1
|
&C1
|
&D3
|
&K3
|
--->
|
\N3
|
%C2
|
\N0
|
%C0
|
Intel
External
|
&F
|
S0=1
|
&C1
|
&D3
|
\Q3
|
\J0
|
\N3
|
%C1"H3
|
\N0
|
%C0
|
Pratical
Peripherals
|
&F
|
S0=1
|
&C1
|
&D3
|
&K3
|
--->
|
&Q5
|
&Q9
|
&Q6
|
<---
|
Required Settings and EC/Compression Settings
Table B-2
Modem
|
Settings for Use with AUX Port
|
ASM Platform Specific Settings
|
Comments
|
No Echo
|
No Res
|
ASM only
|
CAB-MDCE
|
Write Memory
|
Codex 3260
|
E0
|
Q1
|
*NA*
|
&S1
|
&W
|
|
USR Courieræ
USR Sportster
|
E0
|
Q1
|
&R1
|
*NA*
|
&W
|
|
Global Village
Teleport Gold
|
E0
|
Q1
|
\Q2
|
*NA*
|
&W
|
|
Telebit
T1600/T3000/WB
|
E0
|
Q1
|
S58=0
|
&S4
|
&W
|
All Telebit modems need to have the speed set explicitly. These examples use 38400 bps. Using what Telebit calls "UNATTENDED ANSWER MODE" is the best place to start a dial in only modem.
|
Telebit
T2500 (ECM)
|
E0
|
Q1
|
&R1
|
&S1
|
&W
|
Telebit
Trailblazer
|
E0
|
Q1
|
s58=0
|
*NA*
|
&W
|
Use "ENHANCED COMMAND MODE" on the T2500.
|
AT&T Paradyne Dataport
|
E0
|
Q1
|
\Q2
|
*NA*
|
&W
|
Almost all Microcom modems have similar configuration parameters.
|
Hayes modems Accura/
Optima
|
E0
|
Q1
|
*NA*
|
*NA*
|
&W
|
|
Microcom
QX4232 series
|
E0
|
Q1
|
\Q2
|
*NA*
|
&W
|
|
Motorola UDS
FastTalk II
|
E0
|
Q1
|
\Q2
|
*NA*
|
&W
|
|
Multitech
MT1432 MT932
|
E0
|
Q1
|
&E12
|
&S1
|
&W
|
|
Digicom
Scout Plus
|
E0
|
Q2
|
*NA*
|
&B2
|
&W
|
|
Digicom
SoftModem
|
E0
|
Q1
|
*NA*
|
&S1
|
&W
|
|
Viva
14.4/9642c
|
E0
|
Q1
|
*NA*
|
&S1
|
&W
|
|
ZyXel
U-1496E
|
E0
|
Q1
|
*NA*
|
&S1
|
&W
|
Additional information on ftp.zyxel.com
|
Supra
V.32bis/28.8
|
E0
|
Q1
|
*NA*
|
&S1
|
&W
|
|
ZOOM
14.4
|
E0
|
Q1
|
*NA*
|
&S1
|
&W
|
|
Intel
External
|
E0
|
Q1
|
\Q2
|
*NA*
|
&W
|
|
Pratical
Peripherals
|
E0
|
Q1
|
*NA*
|
*NA*
|
&W
|
Based on PC288LCD. May vary.
|
AUX and Platform Specific Settings
contains a legend of symbols used in and .
Table B-3 Legend to Symbols Used in Modem Chart
Symbol
|
Meaning
|
*NA*
|
This option is not available on the noted modem.
|
-->
|
The command noted on the right will handle that function.
|
<--
|
The command on the left will handle that function.
|
AUX port
|
These parameters are only required for pre-9.21 aux ports or any other port without modem control set.
|
Troubleshooting Tips
contains troubleshooting tips on modem access and control.
Table B-4
Problem
|
Likely Cause
|
Connection refused.
|
Someone already has a conncction to that port
-or-
an EXEC is running on that port
-or-
the modem failed to lower CD after a call disconnected, resulting in an EXEC that remained active after disconnect.
In order to force the line back into an idle state, clear the line from the console and try again. If it still fails, ensure that you have set modem inout for that line. If you don't have modem control, either turn off EXEC on the line (by using the exec-timeout line configuration command) before making a reverse connection or configure the modem using an external terminal. As a last resort, disconnect the modem, clear the line, make the Telnet connection and then attach the modem. The prevents a misconfigured modem from denying you line access.
|
Connection appears to hang.
|
Try entering "^U" (clear line), "^Q" (XON), and press Return a few times to try to establish terminal control.
|
EXEC does not come up, autoselect is on.
|
Press Return to enter EXEC.
|
Modem does not hang up after entering quit.
|
The modem is either not receiving DTR information or you have not set up modem control on the Cisco access server or router.
|
Interrupt another user's session when you dial in.
|
The modem is either not dropping CD on disconnect or you have not set up modem control on the Cisco access server or router.
|
Connection hangs after entering "+++" on the dialing modem, followed by an ATO.
|
The answering modem saw and interpreted the "+++"when it was echoed to you. This is a bug in the answering modem, common to many modems. There may be a switch to work around this problem; check the modem's documentation.
|
Losing data.
|
You may have Hardware Flow Control only on for either the router or access server's line (DTE) or the modem (DCE). Hardware Flow Control should be on for both or neither.
|
Using MDCE.
|
Turn MDCE into an MMOD by moving pin 6 to pin 8 as most modems use CD and not DSR to indicate the presence of carrier. You can also program some modems to provide carrier info via DSR.
|
Modem Troubleshooting Tips
