Configuring Subnetwork Bandwidth Manager
Configuring Subnetwork Bandwidth Manager
Last Updated: July 24, 2012
This chapter describes the tasks for configuring the Subnetwork Bandwidth Manager (SBM) feature, which is a signalling feature that enables Resource Reservation Protocol (RSVP)-based admission control over IEEE 802-styled networks.
For complete conceptual information, see "Signalling Overview" module.
For a complete description of the SBM commands in this chapter, see the Cisco IOS Quality of Service Solutions Command Reference. To locate documentation of other commands that appear in this chapter, use the command reference master index or search online.
Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS and Catalyst OS software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn . An account on Cisco.com is not required.
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Subnetwork Bandwidth Manager Configuration Task List
To configure SBM, perform the tasks described in the following sections. The task in the first section is required; the tasks in the remaining sections are optional.
Configuring an Interface as a Designated SBM Candidate
SBM is used in conjunction with RSVP. Therefore, before you configure an interface as a Designated SBM (DSBM) contender, ensure that RSVP is enabled on that interface.
To configure the interface as a DSBM candidate, use the following command in interface configuration mode:
Configuring the NonResvSendLimit Object
The NonResvSendLimit object specifies how much traffic can be sent onto a managed segment without a valid RSVP reservation.
To configure the NonResvSendLimit object parameters, use the following commands in interface configuration mode, as needed:
To configure the per-flow limit on the amount of traffic that can be sent without a valid RSVP reservation, configure the rate, burst, peak, min-unit, and max-unit keywords for finite values from 0 to infinity.
To allow all traffic to be sent without a valid RSVP reservation, configure the rate, burst, peak, min-unit, and max-unit keywords for unlimited. To configure the parameters for unlimited, you can either omit the command or enter the no version of the command (for example, no ip rsvp dsbm non-resv-send-limit rate). Unlimited is the default value.
The absence of the NonResvSendLimit object allows any amount of traffic to be sent without a valid RSVP reservation.
Verifying Configuration of SBM State
To display information that enables you to determine if an interface has been configured as a DSBM candidate and which of the contenders has been elected the DSBM, use the following command in EXEC mode:
The displayed output from the show ip rsvp sbm command identifies the interface by name and IP address, and it shows whether the interface has been configured as a DSBM contender. If the interface is a contender, the DSBM Priority field displays its priority. The DSBM election process is dynamic, addressing any new contenders configured as participants. Consequently, at any given time, an incumbent DSBM might be replaced by one configured with a higher priority. The following example shows sample output from the show ip rsvp sbm command:
Router# show ip rsvp sbm Interface DSBM Addr DSBM Priority DSBM Candidate My Priority Et1 184.108.40.206 70 yes 70 Et2 220.127.116.11 100 yes 100
If you use the detail keyword, the output is shown in a different format. In the left column, the local DSBM candidate configuration is shown; in the right column, the corresponding information for the current DSBM is shown. In the following example, the local DSBM candidate won election and is the current DSBM:
Router# show ip rsvp sbm detail Interface:Ethernet2 Local Configuration Current DSBM IP Address:10.2.2.150 IP Address:10.2.2.150 DSBM candidate:yes I Am DSBM:yes Priority:100 Priority:100 Non Resv Send Limit Non Resv Send Limit Rate:500 Kbytes/sec Rate:500 Kbytes/sec Burst:1000 Kbytes Burst:1000 Kbytes Peak:500 Kbytes/sec Peak:500 Kbytes/sec Min Unit:unlimited Min Unit:unlimited Max Unit:unlimited Max Unit:unlimited
Example Subnetwork Bandwidth Manager Candidate Configuration
In the following example, RSVP and SBM are enabled on Ethernet interface 2. After RSVP is enabled, the interface is configured as a DSBM and SBM candidate with a priority of 100. The configured priority is high, making this interface a good contender for DSBM status. However, the maximum configurable priority value is 128, so another interface configured with a higher priority could win the election and become the DSBM.
interface Ethernet2 ip address 18.104.22.168 255.255.255.0 no ip directed-broadcast ip pim sparse-dense-mode no ip mroute-cache media-type 10BaseT ip rsvp bandwidth 7500 7500 ip rsvp dsbm candidate 100 ip rsvp dsbm non-resv-send-limit rate 500 ip rsvp dsbm non-resv-send-limit burst 1000 ip rsvp dsbm non-resv-send-limit peak 500 end
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2012 Cisco Systems, Inc. All rights reserved.