Table Of Contents

S

S

SA

1. service affecting. Category of conditions that interrupt payload traffic. See also non-service affecting.

2. security association. Instance of security policy and keying material applied to a data flow.

SAC

single-attached concentrator. FDDI or CDDI concentrator that connects to the network by being cascaded from the master port of another FDDI or CDDI concentrator.

sampling rate

Rate at which samples of a particular waveform amplitude are taken.

SAN

storage area networking. An emerging data communications platform that interconnects servers and storage at Gigabaud speeds. By combining LAN networking models with the core building blocks of server performance and mass storage capacity, SAN eliminates the bandwidth bottlenecks and scalability limitations imposed by previous SCSI bus-based architectures.

SAP

1. service access point. Field defined by the IEEE 802.2 specification that is part of an address specification. Thus, the destination plus the DSAP define the recipient of a packet. The same applies to the SSAP. See also DSAP and SSAP.

2. Service Advertising Protocol. IPX protocol that provides a means of informing network clients, via routers and servers, of available network resources and services. See also IPX.

SAR

segmentation and reassembly. One of the two sublayers of the AAL CPCS, responsible for dividing (at the source) and reassembling (at the destination) the PDUs passed from the CS. The SAR sublayer takes the PDUs processed by the CS and, after dividing them into 48-byte pieces of payload data, passes them to the ATM layer for further processing. See also AAL, ATM, CPCS, CS, and SSCS.

SAS

1. single attachment station. Device attached only to the primary ring of a FDDI ring. Also known as a Class B station. Compare with DAS. See also FDDI.

2. statically assigned socket. Socket that is permanently reserved for use by a designated process. In an AppleTalk network, SASs are numbered 1 to 127; they are reserved for use by specific socket clients and for low-level built-in network services.

satellite communication

Use of orbiting satellites to relay data between multiple earth-based stations. Satellite communications offer high bandwidth and a cost that is not related to distance between earth stations, long propagation delays, or broadcast capability.

SBus

Bus technology used in Sun SPARC-based workstations and servers. The SBus specification was adopted by the IEEE as a new bus standard.

SCA

subordinate certification authority. CA whose public-key certificate is issued by another (superior) CA.

scan

Scan is a nonintrusive analysis technique that identifies the open ports found on each live network device and collects the associated port banners found as each port is scanned. Each port banner is compared against a table of rules to identify the network device, its operating system, and all potential vulnerabilities.

scan line fix up

Mechanism used for non-ECM calls meant to eliminate fax failures caused by an excessive number of received page errors because of data loss. If data loss is detected, the data of the current scan line is discarded and replaced with the previous line or white space.

SCCP

Signaling Connection Control Part. Trillium software that supports routing and translation and management functions and data transfer without logical signaling connections.

SCP

Service Control Point. An element of an SS7-based Intelligent Network that performs various service functions, such as number translation, call setup and teardown, and so on.

SCR

sustainable cell rate. Parameter defined by the ATM Forum for ATM traffic manage- ment. For VBR connections, SCR determines the long-term average cell rate that can be transmitted. See also VBR.

SCTE

serial clock transmit external. Timing signal that DTE echoes to DCE to maintain clocking. SCTE is designed to compensate for clock phase shift on long cables. When the DCE device uses SCTE instead of its internal clock to sample data from the DTE, it is better able to sample the data without error even if there is a phase shift in the cable. See also phase shift.

SDH

Synchronous Digital Hierarchy. European standard that defines a set of rate and format standards that are transmitted using optical signals over fiber. SDH is similar to SONET, with a basic SDH rate of 155.52 Mbps, designated at STM-1. See also SONET and STM-1.

SDLC

Synchronous Data Link Control. SNA data link layer communications protocol. SDLC is a bit-oriented, full-duplex serial protocol that has spawned numerous similar protocols, including HDLC and LAPB. See also HDLC and LAPB.

SDLC broadcast

See SDLC broadcast in the "Cisco Systems Terms and Acronyms" section.

SDLC Transport

See SDLC Transport in the "Cisco Systems Terms and Acronyms" section.

SDLLC

See SDLLC in the "Cisco Systems Terms and Acronyms" section.

SDP

1. Session Definition Protocol. An IETF protocol for the definition of Multimedia Services. SDP messages can be part of SGCP and MGCP messages.

2. Session Data Protocol. SDP is intended for describing multimedia sessions for the purposes of session announcement, session invitation, and other forms of multimedia session initiation. [RFC 2327]

SDSL

single-line digital subscriber line. One of four DSL technologies. SDSL delivers 1.544 Mbps both downstream and upstream over a single copper twisted pair. The use of a single twisted pair limits the operating range of SDSL to 10,000 feet (3048.8 meters). Compare with ADSL, HDSL, and VDSL.

SDSU

SMDS DSU. DSU for access to SMDS via HSSIs and other serial interfaces.

SDU

service data unit. Unit of information from an upper-layer protocol that defines a service request to a lower-layer protocol.

SEAL

simple and efficient AAL. Scheme used by AAL5 in which the SAR sublayer segments CS PDUs without adding additional fields. See also AAL, AAL5, CS, and SAR.

SECAM

TV system used in France and elsewhere, utilizing an 8 MHz-wide modulated signal.

secondary

See secondary station.

secondary ring

One of the two rings making up an FDDI or CDDI ring. The secondary ring usually is reserved for use in the event of a failure of the primary ring. Compare with primary ring.

secondary station

In bit-synchronous data link layer protocols, such as HDLC, a station that responds to commands from a primary station. Sometimes referred to simply as a secondary. See also primary station.

section

Portion of a transmission facility, including terminating points between a terminal NE and a regenerator or two regenerators. A terminating point is the point after signal regeneration at which performance is monitored or can be monitored.

section data communications channel

A SONET-embedded operations channel that is processed by each STE node in a network. It provides many data channels for maintenance and operations functions, such as orderwire, performance monitoring, and craft/OS data communication channel (DCN) extension.

Section DCC

Section Data Communications Channel. In OSS, a 192-kbps data communications channel embedded in the section overhead for OAM&P traffic between two SONET network elements. See also OAM&P and SONET.

Secure Shell Protocol

Protocol that provides a secure remote connection to a router through a Transmission Control Protocol (TCP) application.

secure state

System condition in which no subject can access any object in an unauthorized manner.

security association

An instance of security policy and keying material applied to a data flow. Both IKE and IPSec use SAs, although SAs are independent of one another. IPSec SAs are unidirectional and are unique in each security protocol. An IKE SA is used by IKE only, and unlike the IPSec SA, it is bidirectional. IKE negotiates and establishes SAs on behalf of IPSec. A user also can establish IPSec SAs manually. A set of SAs are needed for a protected data pipe, one per direction per protocol. For example, if you have a pipe that supports ESP between peers, one ESP SA is required for each direction. SAs are identified uniquely by destination (IPSec endpoint) address, security protocol (AH or ESP), and security parameter index (SPI).

security management

One of five categories of network management defined by ISO for the management of OSI networks. Security management subsystems are responsible for controlling access to network resources. See also accounting management, configuration management, fault management, and performance management.

security parameter index

See SPI. This is a number that, together with a destination IP address and a security protocol, uniquely identifies a particular security association. When using IKE to establish the security associations, the SPI for each security association is a pseudo-randomly derived number. Without IKE, the SPI is specified manually for each security association.

seed router

Router in an AppleTalk network that has the network number or cable range built in to its port descriptor. The seed router defines the network number or cable range for other routers in that network segment and responds to configuration queries from nonseed routers on its connected AppleTalk network, allowing those routers to confirm or modify their configurations accordingly. Each AppleTalk network must have at least one seed router. See also nonseed router.

SEFS

severely errored framing second. A PM parameter that counts out-of-frame seconds.

segment

1. Section of a network that is bounded by bridges, routers, or switches.

2. In a LAN using a bus topology, a segment is a continuous electrical circuit that often is connected to other such segments with repeaters.

3. Term used in the TCP specification to describe a single transport layer unit of information. The terms datagram, frame, message, and packet also are used to describe logical information groupings at various layers of the OSI reference model and in various technology circles.

segmentation and reassembly

See SAR.

selector

Identifier (octet string) used by an OSI entity to distinguish among multiple SAPs at which it provides services to the layer above.

sequence number protection

See SNAP.

Sequenced Packet Exchange

See SPX.

Sequenced Packet Protocol

See SPP.

Sequenced Routing Update Protocol

See SRTP.

serial clock transmit external

See SCTE.

Serial Line Internet Protocol

See SLIP.

serial transmission

Method of data transmission in which the bits of a data character are transmitted sequentially over a single channel. Compare with parallel transmission.

serial tunnel

See STUN in the "Cisco Systems Terms and Acronyms" section.

server

Node or software program that provides services to clients. See also back end, client, and FRF.11.

Server Message Block

See SMB.

service access point

See SAP.

Service Advertising Protocol

See SAP.

service class

Collection of service types required for a specific service offered. Each service class includes the attributes and values that define the type or quality of service associated with a given class. For example, data connectivity is a service class you might define that includes the service type data-bandwidth.

service data unit

See SDU.

service level

Various levels and quality of services defined for each service type. For example, the service type called quality of sound might have service levels defined for telephone, broadcast, and digital CD.

service package

Quality of service that a cable provider offers subscribers. For example, Basic Student, Family Plus, and Internet are possible service packages. Subscribers may choose one or more service packages. A service class is selected for each service package, defining which service types make up the service package.

service point

Interface between non-SNA devices and NetView that sends alerts from equipment unknown to the SNA environment.

service profile identifier

See SPID.

Service Specific Connection Oriented Protocol

See SSCOP.

service specific convergence sublayer

See SSCS.

service tuple

Service type and level pair. For example, the service tuple data-bandwidth=45 Mbps consists of the service type data-bandwidth and the service level 45 Mbps.

service type

A component of a service that cable providers offer subscribers. For example, devices-supported might be a service type defined for the home networking service, indicating the number of computers the subscriber can connect to the cable network from home. One or more service levels is defined for each service type.

SES

severely errored second. Second during which the bit error ratio is greater than a specified limit and transmission performance is significantly degraded. A PM parameter is measured on a per-channel basis.

session

1. Related set of communications transactions between two or more network devices.

2. In SNA, a logical connection enabling two NAUs to communicate.

session group

Logically ordered list of sessions based on priority of the sessions. All the sessions in the session group should be configured to connect the same physical machines.

session layer

Layer 5 of the OSI reference model. This layer establishes, manages, and terminates sessions between applications and manages the data exchange between presentation layer entities. Corresponds to the data flow control layer of the SNA model. See also application layer, data-link layer, network layer, physical layer, PQ, and transport layer.

session manager

Manages all the sessions in a specific client.

session set

Collection of session groups.

SET

Secure Electronic Transactions. SET specification developed to allow for secure credit card and off-line debit card (check card) transactions over the World Wide Web.

SF

Super Frame. Common framing type used on T1 circuits. SF consists of 12 frames of 192 bits each, with the 193rd bit providing error checking and other functions. SF is superseded by ESF but is still widely used. Also called D4 framing. See also ESP.

S-frame

Supervisory frame. One of three SDLC frame formats. See also I-frame and U-frame.

SG

signaling gateway. Gateway that supports only signaling traffic (no bearer traffic.) For example, a gateway that terminates SS7 A-links is a signaling gateway.

SGCP

Simple Gateway Control Protocol. Controls Voice over IP gateways by an external call control element (called a call-agent). This has been adapted to allow SGCP to control switch ATM Circuit Emulation Service circuits (called endpoints in SGCP). The resulting system (call-agents and gateways) allows for the call-agent to engage in Common Channel Signalling (CCS) over a 64-kbps CES circuit, governing the interconnection of bearer channels on the CES interface.

SGML

Standardized Generalized Markup Language. International standard for the definition of system-independent, device-independent methods of representing text in electronic form.

SGMP

Simple Gateway Monitoring Protocol. Network management protocol that was considered for Internet standardization and later evolved into SNMP. Documented in RFC 1028. See also SNMP.

SHA-1

Secure Hash Algorithm 1. Algorithm that takes a message of less than 264 bits in length and produces a 160-bit message digest. The large message digest provides security against brute-force collision and inversion attacks. SHA-1 [NIS94c] is a revision to SHA that was published in 1994.

shadowing

Form of replication in which well-defined units of information are copied to several DSAs.

shaping

See traffic shaping.

shared cable modem

Single cable modem servicing multiple CPEs is associated with multiple subscriber/accounts and is administered in the User Registrar Admin UI through a neighborhood.

shielded cable

Cable that has a layer of shielded insulation to reduce EMI.

shielded twisted-pair

See STP.

ships in the night mode

Capability to support both MPLS functions and ATM Forum protocols on the same physical interface, or on the same router or switch platform. In this mode, the two protocol stacks operate independently.

shortest path first algorithm

See SPF.

shortest-path routing

Routing that minimizes distance or path cost through the application of an algorithm.

SID

Service ID. A number that defines (at the MAC sublayer) a particular mapping between a cable modem (CM) and the CMTS. The SID is used for the purpose of upstream bandwidth allocation and class-of-service management.

Signal path

Route of a signal channel that carries signaling data.

signal quality error

See SQE.

signal unit error rate monitor

SS7 MTP 2 function that provides monitoring of signal unit events.

signaling

1. Process of sending a transmission signal over a physical medium for the purposes of communication.

2. In telephony, a term that refers to sending call information across a telephone connection. This information can be transmitted by many techniques, such as opening and closing a loop to stop and start the flow of DC loop current (used to indicate on-hook and off-hook state and to transmit dial-pulsing of digits), sending of ringing voltage to alert the other side of an incoming call, sending digit information in the form of DTMF or MF tones, or sending call state information on a DS0 timeslot by using robbed-bits.

Signaling Connection Control Part

SS7 protocol level that provides connectionless and connection-oriented network services and addressing services. The transport layer for TCAP-based services.

Signaling Gateway

It sends and receives PSTN signalling at the edge of IP/ATM network. It backhauls the signalling to a Media Gateway Controller. The Signaling Gateway function may be coresident with the Media Gateway function to process signaling associated with line or trunk terminations controlled by the Media Gateway.

signaling packet

Generated by an ATM-connected device that wants to establish a connection with another such device. The signaling packet contains the ATM NSAP address of the desired ATM endpoint, as well as any QoS parameters required for the connection. If the endpoint can support the desired QoS, it responds with an accept message, and the connection is opened. See also QoS.

Signaling System 7

See SS7.

signal-to-noise

S/N (also SNR). The difference in amplitude between a baseband signal and the noise in a portion of the spectrum.

Silicon Switch Processor

See SSP in the "Cisco Systems Terms and Acronyms" section.

silicon switching

See silicon switching in the "Cisco Systems Terms and Acronyms" section.

silicon switching engine

See SSE in the "Cisco Systems Terms and Acronyms" section.

SIM

1. subscriber identity module. Component of an MS in a GSM network that contains all the subscriber information.

2. Set Initialization Mode.

simple and efficient AAL

See SEAL.

Simple Gateway Monitoring Protocol

See SGMP.

Simple Mail Transfer Protocol

See SMRP.

Simple Multicast Routing Protocol

See SMRP.

Simple Network Management Protocol

See SNMP.

simplex

Capability for transmission in only one direction between a sending station and a receiving station. Broadcast television is an example of a simplex technology. Compare with full duplex and half duplex.

single attachment station

See SAS.

single in-line memory module

Module that is commonly used for internal Flash memory.

single-attached concentrator

See SAC.

single-mode fiber

Fiber-optic cabling with a narrow core that allows light to enter only at a single angle. Such cabling has higher bandwidth than multimode fiber, but requires a light source with a narrow spectral width (for example, a laser). Also called monomode fiber. See also multimode fiber.

single-route explorer packet

See spanning explorer packet.

single-vendor network

Network using equipment from only one vendor. Single-vendor networks rarely suffer compatibility problems. See also multivendor network.

SINR

The ratio of the received strength of the desired signal to the received strength of undesired signals (noise and interference).

SIP

1. SMDS Interface Protocol. Used in communications between CPE and SMDS network equipment. Allows the CPE to use SMDS service for high-speed WAN internetworking. Based on the IEEE 802.6 DQDB standard. See also DQDB.

2. serial interface processor.

3. session initiation protocol. Protocol developed by the IETF MMUSIC Working Group as an alternative to H.323. SIP features are compliant with IETF RFC 2543, published in March 1999. SIP equips platforms to signal the setup of voice and multimedia calls over IP networks.

Site

Group of closely related configuration data. It can be the name of a physical location or it can be a name you choose to give to one segment of your overall system.

SLAC

Stanford Linear Accelerator Center.

SLC

Signaling link code. Code that identifies a linkset.

sliding window flow control

Method of flow control in which a receiver gives the transmitter permission to transmit data until a window is full. When the window is full, the transmitter must stop transmitting until the receiver advertises a larger window. TCP, other transport protocols, and several data link layer protocols use this method of flow control.

SLIP

Serial Line Internet Protocol. Standard protocol for point-to-point serial connections using a variation of TCP/IP. Predecessor of PPP. See also CSI and PPP.

slotted ring

LAN architecture based on a ring topology in which the ring is divided into slots that circulate continuously. Slots can be either empty or full, and transmissions must start at the beginning of a slot.

SM fiber

single-mode fiber. Fiber with a relatively low diameter through which only one mode can propagate.

SMAC

source MAC. MAC address specified in the Source Address field of a packet. Compare with DMAC. See also MAC address.

SMATV

satellite master antenna television. Transmission of television programming to a Satellite Master Antenna installed on top of an apartment building, a hotel, or at another central location from where it serves a private group of viewers. The transmission usually is done in C-band to 1.5 or 2 meter dishes.

SMB

Server Message Block. File-system protocol used in LAN manager and similar NOSs to package data and exchange information with other systems.

SMDS

Switched Multimegabit Data Service. High-speed, packet-switched, datagram-based WAN networking technology offered by the telephone companies. See also CBDS.

SMDS Interface Protocol

See SIP.

SMF

single-mode fiber.

SMG

Wireless—Special Mobile Group. A standards body within ETSI that develops specifications related to mobile networking technologies, such as GSM and GPRS.

SMI

Structure of Management Information. Document (RFC 1155) specifying rules used to define managed objects in the MIB. See also MIB.

SMO

state machine object.

smoothing

See traffic shaping.

SMRP

Simple Multicast Routing Protocol. Specialized multicast network protocol for routing multimedia data streams on enterprise networks. SMRP works in conjunction with multicast extensions to the AppleTalk protocol.

SMT

Station Management. ANSI FDDI specification that defines how ring stations are managed.

SMTP

Simple Mail Transfer Protocol. Internet protocol providing e-mail services.

SNA

Systems Network Architecture. Large, complex, feature-rich network architecture developed in the 1970s by IBM. Similar in some respects to the OSI reference model but with a number of differences. SNA essentially is composed of seven layers. See also data flow control layer, data-link control layer, path control layer, physical control layer, presentation services layer, transaction services layer, and transmission control layer.

SNA Distribution Services

See SNADS.

SNA Network Interconnection

See SNI.

SNADS

SNA Distribution Services. Consists of a set of SNA transaction programs that interconnect and cooperate to provide asynchronous distribution of information between end users. One of three SNA transaction services. See also DDM and DIA.

SNAP

Subnetwork Access Protocol. Internet protocol that operates between a network entity in the subnetwork and a network entity in the end system. SNAP specifies a standard method of encapsulating IP datagrams and ARP messages on IEEE networks. The SNAP entity in the end system makes use of the services of the subnetwork and performs three key functions: data transfer, connection management, and QoS selection.

SNI

1. Subscriber Network Interface. Interface for SMDS-based networks that connects CPE and an SMDS switch. See also UNI.

2. SNA Network Interconnection. IBM gateway connecting multiple SNA networks.

SNMP

Simple Network Management Protocol. Network management protocol used almost exclusively in TCP/IP networks. SNMP provides a means to monitor and control network devices, and to manage configurations, statistics collection, performance, and security. See also SGMP and SNMP2.

SNMP communities

Authentication scheme that enables an intelligent network device to validate SNMP requests.

SNMP2

SNMP Version 2. Version 2 of the popular network management protocol. SNMP2 supports centralized as well as distributed network management strategies, and includes improvements in the SMI, protocol operations, management architecture, and security. See also SNMP.

SNP

sequence number protection.

SNPA

subnetwork point of attachment. Data link layer address (such as an Ethernet address, X.25 address, or Frame Relay DLCI address). SNPA addresses are used to configure a CLNS route for an interface.

SNR

signal-to-noise ratio. SNR is the ratio of usable signal being transmitted to the undesired signal (noise). It is a measure of transmission quality. The ratio of good data (signal) to bad (noise) on a line, expressed in decibels (dB).

SNRM

Set Normal Response.

SNRME

Set Normal Response. Mode Exchange.

socket

1. Software structure operating as a communications end point within a network device.

2. Addressable entity within a node connected to an AppleTalk network; sockets are owned by software processes known as socket clients. AppleTalk sockets are divided into two groups: SASs, which are reserved for such clients as AppleTalk core protocols, and DASs, which are assigned dynamically by DDP upon request from clients in the node. An AppleTalk socket is similar in concept to a TCP/IP port.

socket client

Software process or function implemented in an AppleTalk network node.

socket listener

Software provided by a socket client to receive datagrams addressed to the socket. See also socket client.

socket number

8-bit number that identifies a socket. A maximum of 254 different socket numbers can be assigned in an AppleTalk node.

software generic

The system operating software release for general availability.

SOHO

small office, home office. Networking solutions and access technologies for offices that are not directly connected to large corporate networks.

SONET

Synchronous Optical Network. A standard format for transporting a wide range of digital telecommunications services over optical fiber. SONET is characterized by standard line rates, optical interfaces, and signal formats.

High-speed (up to 2.5 Gbps) synchronous network specification developed by Bellcore and designed to run on optical fiber. STS-1 is the basic building block of SONET. Approved as an international standard in 1988. See also SDH, STS-1, and STS-3c.

SONET multiplexing

SONET multiplexing byte interlaces the lower-rate payloads, which creates a high-rate synchronous signal.

source address

Address of a network device that is sending data. See also destination address.

source MAC

See SMAC.

source node

A source node is the originating node of an end-to-end channel or virtual wavelength path (VWP).

source service access point

See SSAP.

source-route bridging

See SRP.

source-route translational bridging

See SR/TLB.

source-route transparent bridging

See SRT.

Southeastern Universities Research Association Network

See SURAnet.

SP

1. Signaling Processor, Signaling Point.

2. See SP in the "Cisco Systems Terms and Acronyms" section.

SPA

See SPA in the "Cisco Systems Terms and Acronyms" section.

SPAG

Standards Promotion and Application Group. Group of European OSI manufacturers that chooses option subsets and publishes these in the "Guide to the Use of Standards" (GUS).

spam

Term used to describe unsolicited e-mail or newsgroup posts, often in the form of commercial announcements. The act of sending a spam is called, naturally, spamming.

span

Full-duplex digital transmission line between two digital facilities.

SPAN

See SPAN (Switched Port Analyzer) in the "Cisco Systems Terms and Acronyms" section.

spanning explorer packet

Follows a statically configured spanning tree when looking for paths in an SRB network. Also known as a limited-route explorer packet or a single-route explorer packet. See also all-routes explorer packet, explorer packet, and local explorer packet.

spanning tree

Loop-free subset of a network topology. See also spanning-tree algorithm and Spanning-Tree Protocol.

spanning-tree algorithm

Algorithm used by the Spanning-Tree Protocol to create a spanning tree. Sometimes abbreviated as STA. See also spanning tree and Spanning-Tree Protocol.

Spanning-Tree Protocol

See STP.

sparse mode PIM

See PIM sparse mode.

SPC

Service Platform Card. Provides call processing services, such as tone receivers and conference ports, within the Cisco VCO/4K switch. Available resources include DTMF detection, call progress analysis, MF reception, MFCR2 reception and transmission, tone generation, DTMF and MF outpulsing, and call conferencing.

SPE

1. synchronous payload envelope. The payload carrying portion of the STS signal in SONET. The SPE is used to transport a tributary signal across the synchronous network. In most cases, this signal is assembled at the point of entry to the synchronous network and is disassembled at the point of exit from the synchronous network. Within the synchronous network, the SPE is passed on intact between NEs on its route through the network.

2. system processing engine. A card that acts as a single-board computer and that runs system software applications, such as Cisco ICS 7750 System Manager and Cisco CallManager.

spectrum reuse

CATV's most fundamental concept. Historically, the over-the-air spectrum has been assigned to many purposes other than that of carrying TV signals. This has resulted in an inadequate supply of spectrum to serve the needs of viewers. Cable can reuse spectrum that is sealed in its aluminum tubes.

speed matching

Feature that provides sufficient buffering capability in a destination device to allow a high-speed source to transmit data at its maximum rate, even if the destination device is a lower-speed device.

SPF

shortest path first algorithm. Routing algorithm that iterates on length of path to determine a shortest-path spanning tree. Commonly used in link-state routing algorithms. Sometimes called Dijkstra's algorithm. See also link-state routing algorithm.

SPI

security parameter index. This is a number that, together with a destination IP address and security protocol, uniquely identifies a particular security association. When using IKE to establish the security associations, the SPI for each security association is a pseudo-randomly derived number. Without IKE, the SPI is manually specified for each security association.

SPID

service profile identifier. Number that some service providers use to define the services to which an ISDN device subscribes. The ISDN device uses the SPID when accessing the switch that initializes the connection to a service provider.

split-horizon updates

Routing technique in which information about routes is prevented from exiting the router interface through which that information was received. Split-horizon updates are useful in preventing routing loops.

SPNNI connection

See SPNNI connection in the "Cisco Systems Terms and Acronyms" section.

spoofing

1. Scheme used by routers to cause a host to treat an interface as if it were up and supporting a session. The router spoofs replies to keepalive messages from the host in order to convince that host that the session still exists. Spoofing is useful in routing environments, such as DDR, in which a circuit-switched link is taken down when there is no traffic to be sent across it in order to save toll charges. See also DDR.

2. The act of a packet illegally claiming to be from an address from which it was not actually sent. Spoofing is designed to foil network security mechanisms, such as filters and access lists.

spooler

Application that manages requests or jobs submitted to it for execution. Spoolers process the submitted requests in an orderly fashion from a queue. A print spooler is a common example of a spooler.

SPP

Sequenced Packet Protocol. Provides reliable, connection-based, flow-controlled packet transmission on behalf of client processes. Part of the XNS protocol suite.

SPX

Sequenced Packet Exchange. Reliable, connection-oriented protocol that supplements the datagram service provided by network layer (Layer 3) protocols. Novell derived this commonly used NetWare transport protocol from the SPP of the XNS protocol suite.

SQE

signal quality error. Transmission sent by a transceiver back to the controller to let the controller know whether the collision circuitry is functional. Also called heartbeat.

SQL

Structured Query Language. International standard language for defining and accessing relational databases.

SR

short reach. The distance specification for optical systems that operate effectively up to 3 km (1.8 mi).

SR/TLB

source-route translational bridging. Method of bridging where source-route stations can communicate with transparent bridge stations with the help of an intermediate bridge that translates between the two bridge protocols. Compare with SRT.

SRAM

Type of RAM that retains its contents for as long as power is supplied. SRAM does not require constant refreshing, like DRAM. Compare with DRAM.

SRB

source-route bridging. Method of bridging originated by IBM and popular in Token Ring networks. In an SRB network, the entire route to a destination is predetermined, in real time, prior to the sending of data to the destination. Contrast with transparent bridging.

SRCP

Simple Resource Control Protocol. Set of extensions to MGCP to allow the VSC to poll the gateway about its current configuration.

SRP

spatial reuse protocol.

SRT

source-route transparent bridging. IBM bridging scheme that merges the two most prevalent bridging strategies: SRB and transparent bridging. SRT employs both technologies in one device to satisfy the needs of all ENs. No translation between bridging protocols is necessary. Compare with SR/TLB.

SRTP

Sequenced Routing Update Protocol. Protocol that assists VINES servers in finding neighboring clients, servers, and routers. See also RTP (Routing Table Protocol).

SRVTAB

Password that a network service shares with the KDC. The network service authenticates an encrypted service credential by using the SRVTAB (also known as a KEYTAB) to decrypt it.

SS7

Signaling System 7. Standard CCS system used with BISDN and ISDN. Developed by Bellcore. See also CCS.

SSAP

source service access point. SAP of the network node designated in the Source field of a packet. Compare to DSAP. See also SAP (service access point).

SSCOP

Service Specific Connection Oriented Protocol. Data link protocol that guarantees the delivery of ATM signaling packets.

SSCP

system services control points. Focal points within an SNA network for managing network configuration, coordinating network operator and problem determination requests, and providing directory services and other session services for network end users.

SSCP-PU session

Session used by SNA to allow an SSCP to manage the resources of a node through the PU. SSCPs can send requests to, and receive replies from, individual nodes in order to control the network configuration.

SSCS

service specific convergence sublayer. One of the two sublayers of any AAL. SSCS, which is service dependent, offers assured data transmission. The SSCS can be null as well, in classical IP over ATM or LAN emulation implementations. See also AAL, ATM layer, CPCS, CS, and SAR.

SSD server

Service Selection Dashboard server. Customizable Web-based application that works with the Cisco SSG to allow end customers to login to and disconnect from proxy and passthrough services through a standard Web browser. After the customer logs in to the network of the service provider, an HTML Dashboard is populated with the services authorized for that user.

SSE

See SSE in the "Cisco Systems Terms and Acronyms" section.

SSG

Service Selection Gateway. Gateway that offers service providers a means for menu-based service selection. End users can select services from the Dashboard menu, and the Cisco SSG can set up and tear down proxy and passthrough network connections based on a selection of a user. The Cisco SSG accounts for the services selected so that service providers can bill for individual services.

SSL

Secure Socket Layer. Encryption technology for the Web used to provide secure transactions, such as the transmission of credit card numbers for e-commerce.

SSM

Source Specific Multicast. A datagram delivery model that best supports one-to-many applications, also known as broadcast applications. SSM is the core networking technology for the Cisco implementation of the IP Multicast Lite suite of solutions targeted for audio and video broadcast application environments.

SSN

Subsystem number.

SSO

system security officer. Person responsible for enforcement or administration of the security policy that applies to the system.

SSP

1. system switch processor. A card that acts as an Ethernet switch and passes data between all system cards and to any other switches connected to the system.

2. service switching point. Element of an SS7-based Intelligent Network that performs call origination, termination, or tandem switching.

3. Switch-to-Switch Protocol. Protocol specified in the DLSw standard that routers use to establish DLSw connections, locate resources, forward data, and handle flow control and error recovery. See also DLSw.

4. Silicon Switch Processor. See SSP in the "Cisco Systems Terms and Acronyms" section.

SSRP

Simple Server Redundancy Protocol. The LANE simple server redundancy feature creates fault-tolerance using standard LANE protocols and mechanisms. Also called SSRP. See also FSSRP.

STA

See spanning-tree algorithm.

stack

See protocol stack.

standard

Set of rules or procedures that are either widely used or officially specified. See also de facto standard and de jure standard.

standby monitor

Device placed in standby mode on a Token Ring network in case an active monitor fails. See also active monitor and ring monitor.

star topology

LAN topology in which end points on a network are connected to a common central switch by point-to-point links. A ring topology that is organized as a star implements a unidirectional closed-loop star, instead of point-to-point links. Compare with bus topology, ring topology, and tree topology.

StarLAN

CSMA/CD LAN, based on IEEE 802.3, developed by AT&T.

start-stop transmission

See asynchronous transmission.

startup range

Range of values (from 65280 to 65534) from which an AppleTalk node selects the network number part of its provisional address if it has not saved another network number.

stat mux

See statistical multiplexing.

static route

Route that is explicitly configured and entered into the routing table. Static routes take precedence over routes chosen by dynamic routing protocols.

statically assigned socket

See SAS.

Station Management

See SMT.

statistical multiplexing

Technique whereby information from multiple logical channels can be transmitted across a single physical channel. Statistical multiplexing dynamically allocates bandwidth only to active input channels, making better use of available bandwidth and allowing more devices to be connected than with other multiplexing techniques. Also referred to as statistical time-division multiplexing or stat mux. Compare with ATDM, FDM, and TDM.

statistical time-division multiplexing

See statistical multiplexing.

STD

Subseries of RFCs that specify Internet standards. The official list of Internet standards is in STD 1.

STM-1

Synchronous Transport Module level 1. One of a number of SDH formats that specifies the frame structure for the 155.52-Mbps lines used to carry ATM cells. See also SDH.

store and forward

Function whereby a message is transmitted to some intermediate relay point and temporarily stored before forwarding to the next relay point.

store and forward packet switching

Packet-switching technique in which frames are completely processed before being forwarded out the appropriate port. This processing includes calculating the CRC and checking the destination address. In addition, frames must be stored temporarily until network resources (such as an unused link) are available to forward the message. Contrast with cut-through packet switching.

STP

1. shielded twisted-pair. Two-pair wiring medium used in a variety of network implementations. STP cabling has a layer of shielded insulation to reduce EMI. Compare with UTP. See also twisted pair.

2. Spanning-Tree Protocol. Bridge protocol that uses the spanning-tree algorithm, enabling a learning bridge to dynamically work around loops in a network topology by creating a spanning tree. Bridges exchange BPDU messages with other bridges to detect loops, and then remove the loops by shutting down selected bridge interfaces. Refers to both the IEEE 802.1 Spanning-Tree Protocol standard and the earlier Digital Equipment Corporation Spanning-Tree Protocol upon which it is based. The IEEE version supports bridge domains and allows the bridge to construct a loop-free topology across an extended LAN. The IEEE version generally is preferred over the Digital version. Sometimes abbreviated as STP. See also Bpdu, learning bridge, MAC address learning, spanning tree, and spanning-tree algorithm.

3. signal transfer point. Element of an SS7-based Intelligent Network that performs routing of the SS7 signaling.

Stratum

Hierarchical clock reference in the PSTN network, where 1 represents the highest possible quality of clocking.

Stratum 3

Precision timing reference that provides a free-run accuracy of plus or minus 4.6 parts per million (PPM), pull-in capability of 4.6 PPM, and holdover stability of fewer than 255 slips during first day. Thorough descriptions can be found in ANSI T1.101-1994 and the Bellcore document GR-1244-CORE.