Table Of Contents

Command Summary for the Cisco Wideband SPA

Command Summary for the Cisco Wideband SPA

---

Table 10-1 provides an alphabetical list of some of the most significant commands that are needed to configure, monitor, and maintain the Cisco Wideband SPA.

For more information about the commands used in this chapter, see the Cisco IOS CMTS Cable Command Reference at the following URL:

http://www.cisco.com/en/US/docs/ios/cable/command/reference/cbl_book.html

Table 10-1 Cisco Wideband SPA Command Summary 

Command	Purpose
Cisco IOS Releases 12.3(23)BC and 12.2(33)SCA Router(config)# card slot/subslot/bay 24rfchannel-spa-1 Cisco IOS Release 12.2(33)SCB Router(config)# card slot/bay 24rfchannel-spa-1	Preprovisions the Cisco Wideband SPA so that it can be configured without being physically present.
Cisco IOS Releases 12.3(23)BC and 12.2(33)SCA Router(config)# hw-module bay slot/subslot/bay shutdown unpowered Cisco IOS Release 12.2(33)SCB Router(config)# hw-module bay slot/bay shutdown unpowered	Powers down a SPA in the specified slot, subslot, and bay.
Cisco IOS Releases 12.3(23)BC and 12.2(33)SCA Router(config)# no hw-module bay slot/subslot/bay shutdown Cisco IOS Release 12.2(33)SCB Router(config)# no hw-module bay slot/bay shutdown	Powers on a SPA in the specified slot, subslot, and bay.
Router(config-controller)# rf-channel rf-port frequency freq [annex {A | B} modulation {64 | 256} [interleave-depth {8 | 12 | 16 | 32 |64 | 128}]]	Sets the frequency, annex (MPEG framing format), modulation and interleave depth for the Cisco Wideband SPA.
Router(config)# cable fiber-node fiber-node-id	Enters cable fiber-node configuration mode so that you can configure a fiber node.
Router(config)# cable rf-bandwidth-percent percent_value	Allocates bandwidth for the modular-cable interfaces.
Router(config-if)# cable rf-channel rf_port [bandwidth-percent bw-percent]	Associates an RF channel on a Cisco Wideband SPA with a wideband channel.
Router(config)# cable wideband auto-reset	Enables wideband auto-reset mode on the CMTS.
Cisco IOS Releases 12.3(23)BC and 12.2(33)SCA Router(config)# controller modular-cable  slot/subslot/bay Cisco IOS Release 12.2(33)SCB Router(config)# controller modular-cable  slot/bay/port	Enters controller configuration mode to configure the Cisco Wideband SPA controller.
Router(config-fiber-node)# description description	Specifies a description for a fiber node.
Router(config-fiber-node)# downstream cable slot/subslot/port	Assigns a primary downstream channel for a fiber node.
Router(config-fiber-node)# upstream cable slot/subslot connector list-of-ports	Specifies the upstream channel ports for a fiber node.
Cisco IOS Releases 12.3(23)BC and 12.2(33)SCA Router(config-if)# downstream modular-cable slot/subslot/bay rf-channel list_of_channels [upstream list_of_upstreams] Cisco IOS Release 12.2(33)SCB Router(config-if)# downstream modular-cable slot/bay/port rf-channel list_of_channels [upstream list_of_upstreams]	Specifies association of a set of uBR10-MC5x20 upstreams with individual modular downstream channels from the SPA into a given cable MAC domain.
Cisco IOS Releases 12.3(23)BC and 12.2(33)SCA Router(config-fiber-node)# downstream modular-cable slot/subslot/bay rf-channel {rf-port | low-high} Cisco IOS Release 12.2(33)SCB Router(config-fiber-node)# downstream modular-cable slot/bay/port rf-channel {rf-port | low-high}	Specifies the RF channels that are available for wideband channels on a fiber node.
Router(config-controller)# ip-address ip-address	Sets the IP address of the Cisco Wideband SPA's FPGA.
Router(config-controller)# modular-host subslot slot/subslot	Specifies the modular-host line card that will be used for Wideband protocol operations.
Router(config-controller)# rf-channel rf-port  [description description] [frequency freq] [ip-address ip-address mac-address mac-address udp-port portnum]	Configures an RF channel on the Cisco Wideband SPA.
Router(config-controller)# rf-channel rf-port cable downstream channel-id channel-id	Assigns a downstream channel ID to an RF channel.
Router# show cable mac-domain cableslot/subslot/port downstream-service-group	Displays MAC Domain Downstream Service Group information for a primary downstream channel.
Cisco IOS Releases 12.3(23)BC and 12.2(33)SCA Router# show controllers modular-cable slot/subslot/bay {brief | fpga_registers | {all | sfp [port port_num] | ge_phy [port port_num] }} Cisco IOS Release 12.2(33)SCB Router# show controllers modular-cable slot/bay/port {brief | fpga_registers | {all | sfp [port port_num] | ge_phy [port port_num] }}	Display Cisco Wideband SPA internal state information.
Cisco IOS Releases 12.3(23)BC and 12.2(33)SCA Router# show hw-module bay [slot/subslot/bay | all] show-type {wideband-channel | rf-channel} [device-index] [verbose] Cisco IOS Release 12.2(33)SCB Router# show hw-module bay [slot/bay | all] show-type {wideband-channel | rf-channel} [device-index] [verbose]	Displays information about the wideband channels or RF channels on a Cisco Wideband SPA.
Cisco IOS Releases 12.3(23)BC and 12.2(33)SCA Router# show hw-module bay {slot/subslot/bay | all} oir [internal] Cisco IOS Release 12.2(33)SCB Router# show hw-module bay {slot/bay | all} oir [internal]	Displays the operational status of a Cisco Wideband SPA.
Cisco IOS Releases 12.3(23)BC and 12.2(33)SCA Router# show interface wideband-cable slot/subslot/bay:wb-channel Cisco IOS Release 12.2(33)SCB Router# show interface wideband-cable slot/bay/port:wb-channel	Displays information about a wideband channel cable interface.