Table Of Contents

Initializing the Detector

Using the Command-Line Interface

Understanding User Privilege Levels

Understanding Command Modes

Entering CLI Commands

Using the no Form of a Command

show Command Syntax

CLI Error Messages

Tips for Using the CLI

Using Help

Using Tab Completion

Understanding Conventions of Operation Direction

Abbreviating a Command

Using Wildcard Characters

Configuring the Detector Interfaces

Configuring a Physical Interface

Clearing the Counters of a Physical Interface

Configuring the Default Gateway

Adding a Static Route to the Routing Table

Managing the Detector

Managing the Detector with a Web-Based Manager

Accessing the Detector with SSH

Initializing the Detector

---

This chapter describes the basic tasks required to initialize the Cisco Traffic Anomaly Detector (Detector) in a network and how to manage it.

This chapter includes the following topics:

•Using the Command-Line Interface

•Configuring the Detector Interfaces

•Configuring the Default Gateway

•Managing the Detector

Using the Command-Line Interface

You can control the Detector functions by using the command-line interface (CLI). The Detector user interface is divided into many different command modes and the access to the CLI is mapped according to user privilege levels. The commands that are available to you depend on which mode you are currently in.

This section includes the following topics:

•Understanding User Privilege Levels

•Understanding Command Modes

•Entering CLI Commands

•Tips for Using the CLI

Understanding User Privilege Levels

The access to the CLI is mapped according to user privilege levels. Each privilege level has its own group of commands.

Table 3-1 describes the user privilege levels.

Table 3-1 User Privilege Levels 

User Privilege Level	Description
Administration (admin)	Provides access to all operations.
Configuration (config)	Provides access to all operations except for operations relating to user definition, deletion, and modification.
Dynamic (dynamic)	Provides access to monitoring and diagnostics operations, detection, and learning-related operations. Users with Dynamic privileges can also configure flex-content filters and dynamic filters.
Show (show)	Provides access to monitoring and diagnostic operations.

---

Note We recommend that users with Administration and Configuration privilege levels configure all filters. Users with lower privilege levels can add and remove dynamic filters.

---

Understanding Command Modes

This section contains summaries of the command and configuration modes used in the Detector CLI. To obtain a list of commands available for each command mode, enter ? at the system prompt.

Table 3-2 lists and describes the Detector command modes.

Table 3-2 Detector Command Configuration Modes 

Mode	Description
Global	Allows you to connect to remote devices and list system information. The Global prompt is the default prompt when you log into the Detector. The command prompt is as follows: user@DETECTOR#
Configuration	Allows you to configure features that affect the Detector as a whole and have restricted user access. To enter configuration mode, use the configure command in global mode. The command prompt is as follows: user@DETECTOR-conf#
Interface configuration	Allows you to configure the Detector networking interfaces. To enter interface configuration mode, use the interface command in configuration mode. The command prompt is as follows: user@DETECTOR-conf-if-<interface-name>#
Router configuration	Allows you to configure the Detector routing configuration. To enter router configuration mode, use the router command in configuration mode. The command prompt is as follows: router>
Zone configuration	Allows you to configure the zone attributes. To enter zone configuration mode, use the zone command in configuration mode or use the configure command in global mode. The command prompt is as follows: user@DETECTOR-conf-zone-<zone-name>#
Policy template configuration	Allows you to configure the zone policy templates. To enter policy template configuration mode, use the policy-template command in zone configuration mode. The command prompt is as follows: user@DETECTOR-conf-zone-<zone-name>-policy_template-<policy-template-nam e>#
Policy configuration	Allows you to configure the zone policies. To enter policy configuration mode, use the policy command in zone configuration mode. The command prompt is as follows: user@DETECTOR-conf-zone-<zone-name>-policy-<policy-path>#
Guard configuration	Allows you to configure the zone definitions that are unique to the Cisco Guard, such as user filters. To enter guard configuration mode, use the guard-conf command in zone configuration mode. The command prompt is as follows: user@DETECTOR-conf-zone-<zone-name>(guard)#

Entering CLI Commands

These sections describes the rules for entering CLI commands:

•Using the no Form of a Command

•show Command Syntax

•CLI Error Messages

Table 3-3 describes the rules for entering CLI commands.

Table 3-3 CLI Rules 

Action	Keyboard Sequence
Scroll through and modify the command history	Use the arrow keys.
Display commands available in a specific command mode	Press Shift and enter the ? (question mark) key
Display a command completion	Type the beginning of the command and press Tab.
Display a command syntax completion(s)	Enter the command and press Tab twice.
Scroll using the more command	Enter the more number-of-lines command. The more command configures the number of additional lines displayed in the window once you press the Spacebar. The default is two lines less than the capability of the terminal. The number-of-lines argument configures the number of additional lines to be displayed once you press the Spacebar.
Scroll on a single screen (within a command output)	Press the Spacebar
Scroll back a single screen (within a command output)	Press the b key
Stop scroll movement	Press the q key
Search forward for a string	Press the / (slash mark) key and enter the string
Search backward for a string	Press the ? (question mark) key and enter the string
Cancel the action or delete a parameter	Use the no form of a specific command
Display information relating to a current operation	Enter the show command
Exit from a current command group level to a higher group level	Enter the exit command
Exit all command group levels and return to the root level	Enter the end command
Display command output from and including the first line that contains a string	Enter the | (vertical bar) and then enter the begin string command
Display command output lines that include a string	Enter the | (vertical bar) and then enter the include string command
Display command output lines that do not include a string	Enter the | (vertical bar) and then enter the exclude string command

---

Note If you enter the exit command at the root level, you exit the CLI environment to the operating system login screen.

---

Using the no Form of a Command

Almost every configuration command also has a no form. In general, use the no form of a command to disable a feature or function. Use the command without the keyword no to enable a disabled feature or function. For example, the event monitor command turns on the event monitor, and the no event monitor command turns it off.

show Command Syntax

You can execute zone-related show commands from the zone configuration mode. Alternatively, you can execute these commands from the global or configuration modes.

The following is the syntax for the show command in global or configuration modes:

show zone zone-name parameters...

The following is the syntax for the show command in zone configuration mode:

show parameters...

---

Note This publication uses the show command syntax from the zone configuration mode unless explicitly specified.

---

CLI Error Messages

The Detector CLI displays error messages in the following situations:

•The syntax of the command is incomplete or incorrect.

•The command does not match the system configuration.

•The operation could not be performed due to a system failure. In this situation, an entry is created in the system log.

Tips for Using the CLI

This section provides tips for using the CLI and includes the following topics:

•Using Help

•Using Tab Completion

•Understanding Conventions of Operation Direction

•Abbreviating a Command

•Using Wildcard Characters

Using Help

The CLI provides context-sensitive help at every mode of the command hierarchy. The help information tells you which commands are available at the current command mode and provides a brief description of each command.

To get help, type ?.

To display help for a command, type ? after the command.

To display all commands available in a mode along with a short description, enter ? at the command prompt.

The help displays commands available in the current mode only.

Using Tab Completion

You can use tab completion to reduce the number of characters that you need to type for a command. Type the first few characters of a command and press Tab to complete the command.

After entering a command that has a value with multiple options, press Tab twice to display a list of possible input parameters, including system-defined parameters and user-defined parameters. For example, if you press Tab twice after entering the policy-template command in zone configuration mode, the list of policy template names is displayed. If you press Tab twice after entering the zone command in configuration mode, zones that are already defined are displayed.

If multiple commands match for a Tab completion action, nothing is displayed; the system repeats the current line that you entered.

The tab completion feature displays only commands available for the current mode.

You can disable tab completion for zone names in all commands in global and configuration modes such as the zone command and the show zone commands by using the aaa authorization commands zone-completion tacacs+ command. See the "Disabling Tab Completion of Zone Names" section for more information.

Understanding Conventions of Operation Direction

The order of keywords in the command syntax define the direction of the operation. When you enter the keyword before you enter the command, the Detector copies the data from the Detector to the server. When you enter the command before you enter the keyword, the Detector copies the data from the server to the Detector. For example, the copy log ftp command copies the log file from the Detector to the FTP server. The copy ftp new-version command copies the new software version file from the FTP server to the Detector.

Abbreviating a Command

You can abbreviate commands and keywords to the number of characters that allow a unique abbreviation.

For example, you can abbreviate the show command to sh.

Using Wildcard Characters

You can use an asterisk (*) as a wildcard.

For example, if you enter the learning policy-construction * command, the policy construction phase is activated for all the zones that are configured on the Detector.

If you enter the learning policy-construction scan* command, the policy construction phase is activated for all the zones that are configured on the Detector with names that begin with scan (such as scannet, scanserver, and so on).

If you enter the no zone * command, all zones are removed.

Configuring the Detector Interfaces

The Detector has one management port and two data ports on the supervisor engine. Only one data port is used.

Enter configuration mode to configure the Detector by entering the following command:

configure [terminal]

The following example shows how to enter configuration mode:

user@DETECTOR# configure 

user@DETECTOR-conf#

You must configure the Detector interfaces so that the Detector can operate correctly. Many features are enabled on a per-interface basis. When you enter the interface command, you must specify the interface type and number.

The following guidelines apply to all physical and virtual interface configuration processes:

•The eth1 management port must be configured with an IP address and an IP subnet mask.

•You must activate each interface using the no shutdown command.

To display the status or configuration of an interface, enter the show or show running-config commands.

This section contains the following topics:

•Configuring a Physical Interface

•Clearing the Counters of a Physical Interface

Configuring a Physical Interface

To connect the Detector to a network, configure a physical interface.

---

Caution Do not configure two interfaces on the same subnet or the Detector routing may not work properly.

---

To configure a physical interface, perform the following steps:

---

Step 1 Enter interface configuration mode by entering the following command in configuration mode:

interface if-name

The if-name argument specifies the interface name.

The Detector supports the following interfaces:

•eth1—Management port

•giga2—Data port

Step 2 On the eth1 management port only, set the interface IP address by entering the following command:

ip address ip-addr ip-mask 

The ip-addr and ip-mask arguments define the interface IP address. Enter the IP address and subnet mask in dotted-decimal notation (for example, an IP address of 192.168.100.1 and a subnet mask of 255.255.255.0).

Step 3 (Optional) Define the interface MTU by entering the following command:

mtu integer 

The integer argument is an integer between 576 and 1800 for all interfaces. The default MTU value is 1500 bytes.

Step 4 Activate the interface by entering the following command:

no shutdown

---

After activating or deactivating a giga2 data port interface, you must reload the Detector for the configuration change to take effect.

The following example shows how to configure and activate interface eth1:

user@DETECTOR-conf# interface eth1

user@DETECTOR-conf-if-eth1# ip address 10.10.10.33 255.255.255.252

user@DETECTOR-conf-if-eth1# no shutdown

To deactivate a physical interface, use the shutdown command.

Clearing the Counters of a Physical Interface

You can clear the counters of physical interfaces that are used for data (giga) if you are going to perform testing and want to be sure that the counters include information from the testing session only.

To clear the interface counters, use the following command in interface configuration mode:

clear counters

The following example shows how to clear the counters of the interface giga2:

user@DETECTOR-conf-if-giga2# clear counters

Configuring the Default Gateway

The default gateway receives and forwards packets that have IP addresses that are unknown to the local network. In most cases, the Detector default gateway IP address is the adjacent router, located between the Detector and the Internet. The default gateway address must be on the same network as one of the IP addresses of the Detector network interfaces.

To assign a default gateway address, use the following command in configuration mode:

default-gateway ip-addr

The ip-addr argument specifies the default gateway IP address. Enter the IP address in dotted-decimal notation (for example, enter an IP address of 192.168.100.1).

To modify the default gateway address, reenter the command.

The following example shows how to configure the default gateway:

user@DETECTOR-conf# default-gateway 192.168.100.1

Adding a Static Route to the Routing Table

You can add a static route to the Detector routing table. Add a a static route to specify routes for servers or networks outside the local networks that are associated with the Detector IP interfaces.

The static route is added permanently and is not removed after the Detector is rebooted.

To add a static route to the Detector routing table, use the following command in configuration mode:

ip route ip-addr ip-mask nexthop-ip [if-name]

Table 3-4 provides the arguments for the ip route command.

Table 3-4 Arguments for the ip route Command 

Parameter	Description
ip-addr	The network destination of the route. The destination can be an IP network address (where the host bits of the network address are set to 0) or an IP address for a host route. Enter the IP address in dotted-decimal notation (for example, enter 192.168.100.1).
ip-mask	The subnet mask associated with the network destination. Enter the subnet mask in dotted-decimal notation (for example, enter 255.255.255.0).
nexthop-ip	The forwarding or the next-hop IP address over which the set of addresses that are defined by the network destination and subnet mask are reachable. The next-hop IP address should be within the interface subnet. For local subnet routes, the next-hop IP address is the IP address that is assigned to the interface that is attached to the subnet. For remote routes, available across one or more routers, the next-hop IP address is a directly reachable IP address that is assigned to a neighboring router.
if-name	(Optional) The Detector interface over which the destination is reachable. If you do not specify an interface, the next-hop IP address according to the Detector routing table determines the interface used.

The following example shows how to configure a static route:

user@DETECTOR-conf# ip route 172.16.31.5 255.255.255.255 
192.168.100.34

To display the routing table, enter the show ip route command.

Managing the Detector

After you establish a session from the supervisor engine and configure the Detector networking (see "Configuring the Detector Module on the Supervisor Engine" and the "Configuring the Detector Interfaces" section), you can access and manage the Detector using one of the following methods:

•Access using a Secure Shell (SSH) session.

•Access the Detector using a Web-Based Manager (WBM).

•Access from a DDoS-sensing network element. Refer to the appropriate documentation for more information.

This section contains the following topics:

•Managing the Detector with a Web-Based Manager

•Accessing the Detector with SSH

Managing the Detector with a Web-Based Manager

You can manage the Detector from the web with a WBM using a web browser.

To manage the Detector using a WBM, perform the following steps:

---

Step 1 Enable the WBM service by entering the following command in configuration mode:

service wbm

Step 2 Permit access to the Detector from the remote manager IP address by entering the following command in configuration mode:

permit wbm ip-addr [ip-mask]

The ip-addr and ip-mask arguments define the remote manager IP address. Enter the IP address and subnet mask in dotted-decimal notation.

Step 3 Open the browser and enter the following address:

https://Detector-ip-address/ 

The Detector-ip-address argument is the IP address of the Detector.

The Detector WBM window appears.

---

Note HTTPS, not HTTP, is used to enable web-based management control.

---

Step 4 Enter your username and password and click OK.

After you enter the username and password correctly, the Detector home page is displayed.

If TACACS+ authentication is configured, the TACACS+ user database is used for user authentication instead of using the local database. If you have configured advanced authentication attributes on the TACACS+ server, such as password expiry, the Detector may prompt you for a new password based on the configuration of the user on the TACACS+ server or notify you when the password is about to expire.

---

The following example shows how to enable the Detector WBM:

user@DETECTOR-conf# service wbm

user@DETECTOR-conf# permit wbm 192.168.30.32

Accessing the Detector with SSH

You can access the Detector using a Secure Shell (SSH) connection.

The SSH service is enabled by default.

To access the Detector with SSH, perform the following steps:

---

Step 1 Permit access to the Detector from the remote network IP address by entering the following command in configuration mode:

permit ssh ip-addr [ip-mask]

The ip-addr and ip-mask arguments define the remote network IP address. Enter the IP address and subnet mask in dotted-decimal notation (for example, enter 192.168.10.2 for the IP address and 255.255.255.252 for the subnet mask).

Step 2 Establish a connection from the remote network address and enter your login username and password.

If TACACS+ authentication is configured, the TACACS+ user database is used for user authentication instead of using the local database. If you have configured advanced authentication attributes on the TACACS+ server, such as password expiry, the Detector may prompt you for a new password based on the configuration of the user on the TACACS+ server or notify you when the password is about to expire.

To enable the SSH connection without entering a login username and password, perform the following:

•Configure the Detector to use a locally configured login and password for authentication. See the "Configuring Authentication" section for more information.

•Add the remote connection SSH public key to the Detector SSH key list. See the "Managing SSH Keys" section for more information.

---

The following example shows how to enable an SSH connection to the Detector:

user@DETECTOR-conf# permit ssh 192.168.30.32