Table Of Contents
Using the EXEC Command Interpreter
Performing a Basic Configuration
Configuring FE Port Adapter Transmission Mode
Using show Commands to Verify the New Interface Status
Using the show version or show hardware Commands
Using the show interfaces Command
Using the ping Command to Verify Network Connectivity
Configuring the PA-2FEISL
To continue your PA-2FEISL port adapter installation, you must configure the PA-2FEISL interfaces. The instructions that follow apply to all supported platforms. Minor differences between the platforms—with Cisco IOS software commands—are noted.
This chapter contains the following sections:
•
Using the EXEC Command Interpreter
Using the EXEC Command Interpreter
You modify the configuration of your router through the software command interpreter called the EXEC (also called enable mode). You must enter the privileged level of the EXEC command interpreter with the enable command before you can use the configure command to configure a new interface or change the existing configuration of an interface. The system prompts you for a password if one has been set.
The system prompt for the privileged level ends with a pound sign (#) instead of an angle bracket (>). At the console terminal, use the following procedure to enter the privileged level:
Step 1
Router> enablePassword:Step 2
When you enter the correct password, the system displays the privileged-level system prompt (#):
Router#To configure the new interfaces, proceed to the "Configuring the Interfaces" section.
Configuring the Interfaces
After you verify that the new PA-2FEISL is installed correctly (the enabled LED goes on), use the privileged-level configure command to configure the new interfaces. Have the following information available:
•
•
•
If you installed a new PA-2FEISL or if you want to change the configuration of an existing interface, you must enter configuration mode to configure the new interfaces. If you replaced a PA-2FEISL that was previously configured, the system recognizes the new interfaces and brings each of them up in their existing configuration.
For a summary of the configuration options available and instructions for configuring interfaces on a PA-2FEISL, refer to the appropriate configuration publications listed in the "Obtaining Documentation" section on page vii.
You execute configuration commands from the privileged level of the EXEC command interpreter, which usually requires password access. Contact your system administrator, if necessary, to obtain password access. (See the "Using the EXEC Command Interpreter" section for an explanation of the privileged level of the EXEC.)
You can configure each of the interfaces on a PA-FEISL at:
•
Half duplex operation is the default.•
You can also configure one PA-2FEISL interface at 100 mbps, half duplex, and the second PA-2FEISL interface at 200 Mbps, full duplex; 300 Mbps is the maximum aggregate of the two ports.
This section contains the following subsections:
•
•
Performing a Basic Configuration
Following are instructions for a basic configuration: enabling an interface, and specifying IP routing. You might also need to enter other configuration subcommands, depending on the requirements for your system configuration and the protocols you plan to route on the interface. For complete descriptions of configuration subcommands and the configuration options available for fast Ethernet interfaces, refer to the appropriate software documentation.
In the following procedure, press the Return key after each step unless otherwise noted. At any time you can exit the privileged level and return to the user level by entering disable at the prompt as follows:
Router# disableRouter>
Step 1
Router# configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#Step 2
Step 3
Router(config-if)# ip address 10.0.0.0 10.255.255.255Step 4
Step 5
Step 6
Step 7
Step 8
Router# copy running-config startup-config[OK]Router#This completes the procedure for creating a basic configuration.
Configuring FE Port Adapter Transmission Mode
Depending on the requirements for your system configuration and the protocols you plan to route on the interface, you might also need to enter other configuration subcommands. For complete descriptions of configuration subcommands and the configuration options available for Fast Ethernet interfaces, refer to the publications listed in the "Obtaining Documentation" section on page vii.
Note
Half-duplex operation is the default for the PA-2FEISL. To change to full-duplex operation, use the following series of commands:
Router# configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#Router(config)# interface fastethernet 4/0Router(config-if)# full-duplexCtrl-zUse the show interfaces fastethernet command to verify that the 4/0 Fast Ethernet interface is now configured for full-duplex operation as follows:
Router# show interfaces fastethernet 4/0FastEthernet 4/0 is administratively up, line protocol is up(display text omitted)Encapsulation ARPA, loopback not set, keepalive not set, fdx, 100BaseTX(display text omitted)Use the no full-duplex configuration command to return the interface to half-duplex operation as follows:
Router# configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)# interface fastethernet 4/0Router(config-if)# no full-duplexCtrl-zRouter#Use the show interfaces fastethernet command to verify that the 4/0 Fast Ethernet interface is now configured for half-duplex operation as follows:
Router# show interfaces fastethernet 4/0FastEthernet2/0 is administratively up, line protocol is up(display text omitted)Encapsulation ARPA, loopback not set, keepalive not set, hdx, 100BaseTX(display text omitted)This completes the procedure for creating a basic configuration. To check the interface configuration using show commands, proceed to the following section, "Checking the Configuration."
Checking the Configuration
After configuring the new interface, use the show commands to display the status of the new interface or all interfaces, and use the ping command to check connectivity. This section includes the following subsections:
•
•
Using show Commands to Verify the New Interface Status
Table 4-2 demonstrates how you can use the show commands to verify that new interfaces are configured and operating correctly and that the PA-2FEISL appears in them correctly. Sample displays of the output of selected show commands appear in the sections that follow. For complete command descriptions and examples, refer to the publications listed in the "Obtaining Documentation" section on page vii.
Note
If an interface is shut down and you configured it as up, or if the displays indicate that the hardware is not functioning properly, ensure that the interface is properly connected and terminated. If you still have problems bringing up the interface, contact a service representative for assistance. This section includes the following subsections:
•
•
Choose the subsection appropriate for your system. Proceed to the "Using the ping Command to Verify Network Connectivity" section when you have finished using the show commands.
Using the show version or show hardware Commands
Display the configuration of the system hardware, the number of each interface type installed, the Cisco IOS software version, the names and sources of configuration files, and the boot images, using the show version (or show hardware) command.
Note
Cisco 7100 Series Routers
Use the show version (or show hardware) command to display the configuration of the system hardware (the number of each port adapter type installed), the software version, the names and sources of configuration files, and the boot images. The following is an example of the show version command from a Cisco 7120 series router with the PA-2FEISL:
Router #show versionCisco Internetwork Operating System SoftwareIOS (tm) 7200 Software (C7200-JS-M), Version 12.0(5)TCopyright (c) 1986-1999 by cisco Systems, Inc.Compiled Wed 30-Jun-99 13:56 by useridImage text-base:0x60008900, data-base:0x6136A000ROM:System Bootstrap, Version 11.1(13)CA, RELEASE SOFTWARE (f)Router uptime is 27 minutesSystem restarted by reloadSystem image file is "slot0:c7200-js-m.960421", booted via slot0cisco 7206 (NPE200) processor with 57344K/8192K bytes of memory.R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache6 slot midplane, Version 1.3Last reset from power-onBridging software.X.25 software, Version 3.0.0.SuperLAT software copyright 1990 by Meridian Technology Corp).TN3270 Emulation software.4 Ethernet/IEEE 802.3 interface(s)2 FastEthernet/IEEE 802.3 interface(s)4 Token Ring/IEEE 802.5 interface(s)125K bytes of non-volatile configuration memory.4096K bytes of packet SRAM memory.4096K bytes of Flash internal SIMM (Sector size 256K).Configuration register is 0x2100Cisco 7200 Series and Cisco uBR7200 Series Routers
Use the show version (or show hardware) command to display the configuration of the system hardware (the number of each port adapter type installed), the software version, the names and sources of configuration files, and the boot images. The following is an example of the show version command from a Cisco 7200 series router with the PA-2FEISL:
Router #show versionCisco Internetwork Operating System SoftwareIOS (tm) 7200 Software (C7200-JS-M), Version 12.0(5)TCopyright (c) 1986-1999 by cisco Systems, Inc.Compiled Wed 30-Jun-99 13:56 by useridImage text-base:0x60008900, data-base:0x6136A000ROM:System Bootstrap, Version 11.1(13)CA, RELEASE SOFTWARE (f)Router uptime is 27 minutesSystem restarted by reloadSystem image file is "slot0:c7200-js-m.960421", booted via slot0cisco 7206 (NPE200) processor with 57344K/8192K bytes of memory.R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache6 slot midplane, Version 1.3Last reset from power-onBridging software.X.25 software, Version 3.0.0.SuperLAT software copyright 1990 by Meridian Technology Corp).TN3270 Emulation software.4 Ethernet/IEEE 802.3 interface(s)2 FastEthernet/IEEE 802.3 interface(s)4 Token Ring/IEEE 802.5 interface(s)125K bytes of non-volatile configuration memory.4096K bytes of packet SRAM memory.4096K bytes of Flash internal SIMM (Sector size 256K).Configuration register is 0x2100VIP2 in Cisco 7000 Series and Cisco 7500 Series Routers
Use the show version (or show hardware) command to display the configuration of the system hardware (the number of each interface processor type installed), the software version, the names and sources of configuration files, and the boot images. The following is an example of the show version command from a Cisco 7500 series router with the PA-2FEISL:
Router# show versionCisco Internetwork Operating System SoftwareIOS (tm) GS Software (RSP-A), Version 11.1(6)CA [mpo 105]Copyright (c) 1986-1995 by cisco Systems, Inc.Compiled Fri 06-Oct-95 12:22 by mpoImage text-base: 0x600088A0, data-base: 0x605A4000ROM: System Bootstrap, Version 5.3(16645) [biff 571], RELEASED SOFTWAREROM: GS Bootstrap Software (RSP-BOOT-M), Version 11.0(1.2), MAINTENANCEhonda uptime is 4 hours, 22 minutesSystem restarted by reloadSystem image file is "slot0:rsp-a111-1", booted via slot0cisco RSP2 (R4600) processor with 32768K bytes of memory.R4600 processor, Implementation 32, Revision 2.0Last reset from power-onG.703/E1 software, Version 1.0.Bridging software.X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.Chassis Interface.1 VIP2 controllers (1 FastEthernet).1 FastEthernet/IEEE 802.3 interfaces.125K bytes of non-volatile configuration memory.20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).8192K bytes of Flash internal SIMM (Sector size 256K).No slave installed in slot 6.Configuration register is 0x2
Using the show diag Command
Display the types of port adapters installed in your system (and specific information about each) using the show diag slot command, where slot is the port adapter slot in a Cisco 7100 series,
Cisco 7200 series, and Cisco uBR7200 series router and the interface processor slot in a Cisco 7000 series or Cisco 7500 series router with a VIP2.
Note
Cisco 7100 Series Routers
Use the show diag slot command to determine which type of port adapter is installed in your system. Specific port adapter information is displayed, as shown in the following example of a PA-2FEISL-FX in port adapter slot 2:
Router# show diag 2Fastethernet (TX-ISL) port adapter, 2 portsPort adapter is analyzedPort adapter insertion time 00:02:27 agoHardware revision 1.0 Board revision A0Serial number 8500290 Part number 73-2618-01Test history 0x0 RMA number 00-00-00EEPROM format version 1EEPROM contents (hex):0x20: 01 6C 01 00 00 81 B4 42 49 0A 3A 01 00 00 00 000x30: 50 00 00 00 98 04 00 00 00 00 FF FF FF FF FF 00
Note
Note
Cisco 7200 Series and Cisco uBR7200 Series Routers
Use the show diag slot command to determine which type of port adapter is installed in your system. Specific port adapter information is displayed, as shown in the following example of a PA-2FEISL-FX in port adapter slot 2:
Router# show diag 2Fastethernet (TX-ISL) port adapter, 2 portsPort adapter is analyzedPort adapter insertion time 00:02:27 agoHardware revision 1.0 Board revision A0Serial number 8500290 Part number 73-2618-01Test history 0x0 RMA number 00-00-00EEPROM format version 1EEPROM contents (hex):0x20: 01 6C 01 00 00 81 B4 42 49 0A 3A 01 00 00 00 000x30: 50 00 00 00 98 04 00 00 00 00 FF FF FF FF FF 00
Note
VIP2 in Cisco 7000 Series and Cisco 7500 Series Routers
Use the show diag slot command to determine which type of port adapter is installed on a VIP2 in your system. Specific port adapter information is displayed, as shown in the following example of a PA-2FEISL-FX in interface processor slot 3:
Router# show diag 3Slot 3:Physical slot 3, ~physical slot 0xC, logical slot 3, CBus 0Microcode Status 0xCMaster Enable, LED, WCS LoadedBoard is analyzedPending I/O Status: Console I/OEEPROM format version 1VIP2 controller, HW rev 2.04, board revision D0Serial number: 08224085 Part number: 73-1684-03Test history: 0x00 RMA number: 00-00-00Flags: cisco 7000 board; 7500 compatibleEEPROM contents (hex):0x20: 01 15 02 04 00 7D 7D 55 49 06 94 03 00 00 00 000x30: 68 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00Slot database information:Flags: 0x4 Insertion time: 0x1068 (4d22h ago)Controller Memory Size: 8 MBytes DRAM, 1024 KBytes SRAMPA Bay 0 Information:Fast-Ethernet PA, 2 ports, 100BaseFX-ISLEEPROM format version 1HW rev 1.00, Board revision A0Serial number: 00000005 Part number: 73-2619-01PA Bay 1 Information:Fast-Ethernet PA, 2 ports, 100BaseTX-ISLEEPROM format version 1HW rev 1.00, Board revision A0Serial number: 00000027 Part number: 73-2618-01
Note
Using the show interfaces Command
The show interfaces command displays status information (including the physical slot and interface address) for the interfaces you specify. All of the examples that follow specify serial interfaces.
For complete descriptions of interface subcommands and the configuration options available for Cisco 7100 series, Cisco 7200, Cisco uBR7200 series, and VIP2 interfaces, refer to the publications listed in the "Obtaining Documentation" section on page vii.
Note
Cisco 7100 Series Routers
With the show interfaces type slot/port command, use arguments such as the interface type (for example, fastethernet) and the port number (slot/port) to display information about a specific interface only. The following example of the show interfaces fastethernet command shows information specific to a Fast Ethernet interface on a PA-2FEISL in slot 4:
Router# show interfaces fastethernet 4/0FastEthernet4/0 is administratively down, line protocol is downHardware is DEC21140, address is 1.1.1.11 (bia 0000)Internet address is 10.0.0.0MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255Encapsulation ARPA, loopback not set, keepalive not set, fdx, 100BaseTXARP type: ARPA, ARP Timeout 4:00:00Last input 3:08:43, output 3:08:42, output hang neverLast clearing of "show interfaces" counters 2:58:36Output queue 0/40, 0 drops; input queue 0/75, 0 drops5 minute input rate 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/sec0 packets input, 0 bytes, 0 no bufferReceived 0 broadcasts, 0 runts, 0 giants0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort0 watchdog, 0 multicast0 input packets with dribble condition detected0 packets output, 0 bytes, 0 underruns0 output errors, 0 collisions, 0 interface resets, 0 restarts0 babbles, 0 late collision, 0 deferred0 lost carrier, 0 no carrier0 output buffer failures, 0 output buffers swapped out
Note
The Fast Ethernet interface port adapter is numbered as port adapter 4. The Fast Ethernet ports on the PA-2FEISL are interfaces 0 and 1.
Cisco 7200 Series and Cisco uBR7200 Series Routers
With the show interfaces type slot/port command, use arguments such as the interface type (for example, fastethernet) and the port number (slot/port) to display information about a specific interface only. The following example of the show interfaces fastethernet command shows information specific to a Fast Ethernet interface on a PA-2FEISL in slot 4:
Router# show interfaces fastethernet 4/0FastEthernet4/0 is administratively down, line protocol is downHardware is DEC21140, address is 1.1.1.11 (bia 0000)Internet address is 10.0.0.0MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255Encapsulation ARPA, loopback not set, keepalive not set, fdx, 100BaseTXARP type: ARPA, ARP Timeout 4:00:00Last input 3:08:43, output 3:08:42, output hang neverLast clearing of "show interfaces" counters 2:58:36Output queue 0/40, 0 drops; input queue 0/75, 0 drops5 minute input rate 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/sec0 packets input, 0 bytes, 0 no bufferReceived 0 broadcasts, 0 runts, 0 giants0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort0 watchdog, 0 multicast0 input packets with dribble condition detected0 packets output, 0 bytes, 0 underruns0 output errors, 0 collisions, 0 interface resets, 0 restarts0 babbles, 0 late collision, 0 deferred0 lost carrier, 0 no carrier0 output buffer failures, 0 output buffers swapped out
Note
The Fast Ethernet interface port adapter is numbered as port adapter 4. The Fast Ethernet ports on the PA-2FEISL are interfaces 0 and 1.
VIP2 in Cisco 7000 Series or Cisco 7500 Series Routers
Use the show interfaces type slot/port-adapter/port command, with arguments such as the interface type (for example, fastethernet) and the port number (slot/port), to display information about a specific interface. The following example of the show interfaces fastethernet command shows information specific to a Fast Ethernet interface on the PA-2FEISL in slot 3:
Router# show interfaces fastethernet 3/0/0FastEthernet3/0/0 is up, line protocol is upHardware is cyBus FastEthernet Interface, address is 0010.5493.9860 (bia 0010)MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255Encapsulation ARPA, loopback not set, keepalive set (10 sec)Half-duplex, 100Mb/s, 100BaseTX/FXARP type: ARPA, ARP Timeout 04:00:00Last input never, output 00:00:07, output hang neverLast clearing of "show interface" counters neverQueueing strategy: fifoOutput queue 0/40, 0 drops; input queue 0/75, 0 drops5 minute input rate 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/sec0 packets input, 0 bytes, 0 no bufferReceived 0 broadcasts, 0 runts, 0 giants, 0 throttles0 input errors, 0 CRC, 0 frame, 0 overrun, 15654 ignored, 0 abort0 watchdog, 0 multicast0 input packets with dribble condition detected27784 packets output, 2742738 bytes, 0 underruns50 output errors, 0 collisions, 3 interface resets0 babbles, 50 late collision, 119 deferred0 lost carrier, 0 no carrier0 output buffer failures, 0 output buffers swapped outUsing the ping Command to Verify Network Connectivity
Using the ping command, you can verify that an interface port is functioning properly. This section provides a brief description of this command. Refer to the publications listed in the "Obtaining Documentation" section on page vii for detailed command descriptions and examples.
The ping command sends echo request packets out to a remote device at an IP address that you specify. After sending an echo request, the system waits a specified time for the remote device to reply. Each echo reply is displayed as an exclamation point (!) on the console terminal; each request that is not returned before the specified timeout is displayed as a period (.). A series of exclamation points (!!!!!) indicates a good connection; a series of periods (.....) or the messages [timed out] or [failed] indicate a bad connection.
Following is an example of a successful ping command to a remote server with the address 10.0.0.10:
Router# ping 10.0.0.10 <Return>Type escape sequence to abort.Sending 5, 100-byte ICMP Echoes to 10.0.0.10, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 1/15/64 msRouter#If the connection fails, verify that you have the correct IP address for the destination and that the device is active (powered on), and repeat the ping command.
Guest
