Cisco SCE8000 10GBE Installation and Configuration Guide, Release 3.5.5
CLI Commands to Verify a Successful Installation
Download this chapter
CLI Commands to Verify a Successful InstallationCLI Commands to Verify a Successful Installation
Download the complete book
Cisco SCE8000 10GBE Installation and Configuration Guide, Release 3.5.5Cisco SCE8000 10GBE Installation and Configuration Guide, Release 3.5.5 (PDF - 5 MB)
give_us_feedback

Table Of Contents

CLI Commands to Verify a Successful Installation

Introduction

Basic Post-Installation Checklist

CLI Command Output Samples

show version

show inventory

show interface

show system operational status

show interface linecard

show interface linecard connection-mode

show interface linecard link mode

show interface linecard external-bypass

show RDR-formatter

show interface linecard subscriber sm-connection-failure

show ip rpc-adapter sessions


CLI Commands to Verify a Successful Installation

Revised: August 18, 2009, OL-16478-04

Introduction

When you have completed the installation of your Cisco SCE8000 10GBE platform, we recommend that you run a number of CLI commands to verify that the proper components have been successfully installed and are operational.

Basic Post-Installation Checklist

The following table provides a basic post-installation checklist with the related CLI commands. Further verification of the system configuration would depend on the specific topology and configuration of the installation, but this list will verify that the basic installation is operational.

Refer to the descriptions of the individual commands for samples of the command output. Relevant information in the output is in bold.

To check this:
Use this command:
Comments

version

show version

Check the following:

•firmware version

•application version

•management agent status

•management agent version

optics

show inventory

In the physical inventory of the SCE platform, verify that the installed optics are supported by the interfaces.

port configuration

show interface

Run this command for each port to get a listing of the status and configuration of all ports.

operational status

show system operational status

Status should be operational.

This command will give you an indication of problems such as a power problem or external bypass not configured properly.

linecard status

show interface linecard

It should not be shutdown or silent.

connection mode

show interface linecard connection-mode

Make sure that both the connection mode and the failure mode are configured correctly.

link mode

show interface linecard link mode

When connection-mode is inline, link mode should be configured to forwarding.

external bypass configuration

show interface linecard external-bypass

Only if external bypass modules are installed: Check the following:

•Configuration should be activated on failure

•The number of devices should match the number of links

RDR formatter

show RDR-formatter

Verify the following:

•The RDR formatter has established a connection with the configured destinations

•The redundancy status is configured correctly in case of more then one destination.

connection to Subscriber Manager

show interface linecard subscriber sm-connection-failure

If using SM: Verify that the connection with the SM is established.

connection to Quota Manager

show ip rpc-adapter sessions

If using QM: Verify that the connection with the QM is established.


Complete command sequence for a fully-populated SCE8000 10GBE platform using both the SM and the QM

SCE>enable 5
Password:<cisco>
SCE>show version
SCE>show inventory
SCE>show interface TenGigabitEthernet 3/0/0
SCE>show interface TenGigabitEthernet 3/1/0
SCE>show interface TenGigabitEthernet 3/2/0
SCE>show interface TenGigabitEthernet 3/3/0
SCE>show system operation-status
SCE>show interface linecard 0
SCE>show interface linecard 0 connection-mode
SCE>show interface linecard 0 link mode
SCE>show interface linecard 0 external-bypass
SCE>show rdr-formatter
SCE>show interface linecard 0 subscriber sm-connection-failure
SCE>show ip rpc-adapter sessions

CLI Command Output Samples

The text in bold in the following output samples indicates the lines you should check when doing a post-installation check. For some commands, the output is short and the entire output is relevant. In these cases, nothing is in bold.

show version

Look for the following lines:

•System version

•Application file

•Management agent interface version 

SCE>show version

System version: Version 3.5.5 Build 252

Build time: May 31 2009, 15:50:44 (Change-list 483168)

Software version is: Version 3.5.5 Build 252

Cryptography class: K9

Hardware information is:


---------------------

Firmware

---------------------

kernel      : [kernel] 2.3.0/1 (inactive: [kernel] 2.3.0/1)

u-boot      : [uboot] 2.1.0/1 (field: [uboot] 0.8.0/3)

select      : [ubs-cf0] 2.3.0/1 (secondary: [ubs-cf0] 2.3.0/1)


---------------------

Slot 1: SCE8000-SCM-E

---------------------

serial-num  : CAT1151G01D

part-num    : 73-10598-01 36

cpld        : 0x816c

vtpld       : 0xc004

summit-0    : 0x10008

summit-1    : 0x10008

dpt/tx      : 0x4913

cls/ff      : 0x2112

cls cam     : 0x454120

cls flow cap: 33554432

ssa         : 0x90


---------------------

TVR

---------------------

#cpus       : 1

cpu SVR     : 0x80900121

cpu PVR     : 0x80040202

cpu freq    : 1000MHz

cpu (eeprom): 2.1, 800MHz

cpld        : 0xa1bc

cpld-ufm    : 0xa803

summit      : 0x10007

cf          : Model=SILICONSYSTEMS INC 4GB-3213, S/N=357TTR79SY716QC00005, 
FwRev=0x242-0230, Size=4125744KB

phy-0       : 0xcc2

phy-1       : 0xcc2

phy-2       : 0xcc2


---------------------

CFC-0

---------------------

board type  : P2

#cpus       : 3

cpu-0 SVR   : 0x80900121

cpu-0 PVR   : 0x80040202

cpu-0 freq  : 1500MHz

cpu-1 SVR   : 0x80900121

cpu-1 PVR   : 0x80040202

cpu-1 freq  : 1500MHz

cpu-2 SVR   : 0x80900121

cpu-2 PVR   : 0x80040202

cpu-2 freq  : 1500MHz

cpu (eeprom): 2.1, 1500MHz

cpld-0      : 0xb219

cpld-1      : 0xb219

cpld-2      : 0xb219

cpld-0-ufm  : 0xb803

cpld-1-ufm  : 0xb803

cpld-2-ufm  : 0xb803

summit-0    : 0x1000a

summit-1    : 0x1000a

fc          : 0x1100


---------------------

CFC-1

---------------------

board type  : P2

#cpus       : 3

cpu-0 SVR   : 0x80900121

cpu-0 PVR   : 0x80040202

cpu-0 freq  : 1500MHz

cpu-1 SVR   : 0x80900121

cpu-1 PVR   : 0x80040202

cpu-1 freq  : 1500MHz

cpu-2 SVR   : 0x80900121

cpu-2 PVR   : 0x80040202

cpu-2 freq  : 1500MHz

cpu (eeprom): 2.1, 1500MHz

cpld-0      : 0xb219

cpld-1      : 0xb219

cpld-2      : 0xb219

cpld-0-ufm  : 0xb803

cpld-1-ufm  : 0xb803

cpld-2-ufm  : 0xb803

summit-0    : 0x1000a

summit-1    : 0x1000a

fc          : 0x1100


---------------------

Slot 3: SCE8000-SIP

---------------------

serial-num  : CAT1105501R

part-num    : 73-10947-01 11

cpld        : 0x916c

summit-0    : 0xf2c1501

summit-1    : 0xf2c1601

dpt-0       : 0x3110

dpt-1       : 0x3110

ssa-0       : 0x90

ssa-1       : 0x90

spa[0]      : SPA-1X10GE-L-V2

spa[1]      : SPA-1X10GE-L-V2

spa[2]      : SPA-1X10GE-L-V2

spa[3]      : SPA-1X10GE-L-V2


---------------------

SCE8000 Chassis

---------------------

product-num : SCE8000

serial-num  : FOX1208G450

part-num    : 73-11293-01

part-rev    : A0

vid         : V01


Part number       : 73-10598-01 36

Revision          : 1

Software revision : 1

LineCard S/N      : CAT1151G01D

Power Supply type : AC


SML Application information is: 

Application file: /apps/data/scos/app/en355262.sli

Application name: Engage SML Version 3.5.5 build 74

Using Lib - PL_3.5.5_b74

Using Lib - Classifier_3.5.5_b74

Application help: Entry point of Engage

Original source file: 
/auto/srbu-proj1/apps/users/atukh/autoBuild/App/SML/Engage/dev/src/com/pcube/AppTemplate/M
ain/template_app_main.san

Compilation date: Tue, May 19, 2009 at 19:51:58

Compiler version: SANc v3.20 Build 12 built on: Tue 02/01/2009 11:11:05.;SME plugin v1.1

Capacity option used: 'EngageDefaultSCE8000'.

Logger status: Enabled


Platform: SCE8000

Management agent interface version: SCE Agent 3.5.5 Build 121

Software package file: ftp://ftpserver/D:\pcube\Os\3.5.5\252\simba_03550252_K9.pkg

SCE8000  uptime is 5 days, 23 hours, 52 minutes, 40 seconds

show inventory

Look for the following lines:

•All lines containing the text `NAME: "SCE8000 optic'. There should be one line for each installed optic. 

SCE>show inventory

NAME: "SCE8000 Chassis", DESCR: "SCE8000"

PID: SCE8000           , VID: V01, SN: FOX1232G00V


NAME: "SCE8000 Service Control Module (SCM) in slot 1", DESCR: "SCE8000-SCM-E"

PID: SCE8000-SCM-E     , VID: V01, SN: CAT1231G040


NAME: "SCE8000 SPA Interface Processor (SIP) in slot 3", DESCR: "SCE8000-SIP"

PID: SCE8000-SIP       , VID: V01, SN: CAT1229G03H


NAME: "SCE8000 SPA module 3/0", DESCR: "SPA-1X10GE-L-V2"

PID: SPA-1X10GE-L-V2   , VID: V02, SN: JAE1229PFVA


NAME: "SCE8000 SPA module 3/1", DESCR: "SPA-1X10GE-L-V2"

PID: SPA-1X10GE-L-V2   , VID: V02, SN: JAE1229PFR4


NAME: "SCE8000 SPA module 3/2", DESCR: "SPA-1X10GE-L-V2"

PID: SPA-1X10GE-L-V2   , VID: V02, SN: JAE1229PFR6


NAME: "SCE8000 SPA module 3/3", DESCR: "SPA-1X10GE-L-V2"

PID: SPA-1X10GE-L-V2   , VID: V02, SN: JAE1229PFR2


NAME: "SCE8000 FAN 1", DESCR: "SCE8000-FAN"

PID: SCE8000-FAN       , VID: V01, SN: DCH12281410


NAME: "SCE8000 AC power supply 0", DESCR: "PWR-2700-AC/4"

PID: PWR-2700-AC/4     , VID: V02, SN: APS12160003


NAME: "SCE8000 AC power supply 1", DESCR: "PWR-2700-AC/4"

PID: PWR-2700-AC/4     , VID: V02, SN: APS1216002N


NAME: "SCE8000 optic 3/0/0", DESCR: "XFP-10GLR-OC192SR "

PID: XFP-10GLR-OC192SR , VID: V02, SN: ONT121110LJ     


NAME: "SCE8000 optic 3/1/0", DESCR: "XFP-10GLR-OC192SR "

PID: XFP-10GLR-OC192SR , VID: V02, SN: ECL122201CD     


NAME: "SCE8000 optic 3/2/0", DESCR: "XFP-10GLR-OC192SR "

PID: XFP-10GLR-OC192SR , VID: V02, SN: ECL122201CJ     


NAME: "SCE8000 optic 3/3/0", DESCR: "XFP-10GLR-OC192SR "

PID: XFP-10GLR-OC192SR , VID: V02, SN: ECL122103BA

show interface

Run this command for each interface. The command syntax is: 

show interface TenGigabitEthernet 3/bay-number/0

sce>show interface TenGigabitEthernet 3/0/0

Auto negotiation configured: Disabled

Actual status:

        Link is: ON

        Auto negotiation: Disabled

Bandwidth (L1): 10000000 Kbps, Burst-size: 50000 bytes

Pseudo IP Address: Not Configured

show system operational status 

sce>show system operation-status

System Operation status is Operational

show interface linecard 

sce>show interface LineCard 0

The application assigned to slot 0 is /apps/data/scos/app/en35156.sli

Silent is off

Configured shutdown is off

Shutdown due to sm-connection-failure is off

Resulting current shutdown state is off

WAP handling is disabled

show interface linecard connection-mode 

sce>show interface linecard 0 connection-mode 

slot 0 connection mode

Connection mode is inline

slot failure mode is external-bypass

Redundancy status is standalone

show interface linecard link mode 

sce>show interface LineCard 0 link mode

Link mode on all links

Current link mode is           : forwarding

Actual  link mode on active is : forwarding

Actual  link mode on failure is: monopath-bypass

show interface linecard external-bypass 

sce1>show interface LineCard 0 external-bypass 

External bypass current state is 'not activated'.

External bypass failure state is 'activated'.

Amount of expected external bypass devices: 2 (automatically configured).

Amount of detected external bypass devices: 2

show RDR-formatter

Look for:

•Forwarding mode

•Status (in Status column in the Connection Table) 

sce>show RDR-formatter

Status:  enabled

Connection is: up

Forwarding mode: redundancy

Connection Table:

--------------------------------------------------------------------------------

| Collector     | Port  |Status| Priority per Category:                         |

| IP-Address  / |       |      |------------------------------------------------|

| Host-Name     |       |      | Category1 | Category2  | Category3 | Category4 |

|---------------|-------|------|-----------|------------|-----------|-----------|

| 10.240.59.39  | 33000 | up   |100 primary| ---        | ---       | ---       |

| 10.240.59.44  | 33000 | up   | ---       |100 primary | ---       | ---       |

---------------------------------------------------------------------------------

RDR:    queued:     0 ,sent:60108106, thrown:     0, format-mismatch:     0

UM:     queued:     0 ,sent:     0, thrown:     0

Logger: queued:     0 ,sent:     0, thrown:     0

Errors: thrown:     0

Last time these counters were cleared: 07:36:52  EDT  TUE  April  28  2009

show interface linecard subscriber sm-connection-failure

If working with the Subscriber Manager, use this command to make sure the connection with the SM is established 

SCE>show interface linecard 0 subscriber sm-connection-failure 

Current SM link state: up.

Configured action to take when SM link is down: No action.

Changing of system operational-status to 'warning' when SM link is down: enabled.

show ip rpc-adapter sessions

If working with the Quota Manager, use this command to make sure the connection with the QM is established 

sce>show ip rpc-adapter sessions 
client-name=usr.SM

client-address=/10.240.59.36

started=Mon Apr 06 12:43:01 GMT-04:00 2009

received-message-num=408790

sent-message-num=237292

sent-notifications-num=0

dropped-notifications-num=0

client-username=null


client-name=mcn.SM

client-address=/10.240.59.36

started=Mon Apr 06 12:43:02 GMT-04:00 2009

received-message-num=5715112

sent-message-num=6101181

sent-notifications-num=386768

dropped-notifications-num=0

client-username=null


client-name=mcn.QuotaManager-10.248.64.119_10.240.59.36_SCE.J.API.PRPC

client-address=/10.240.59.36

started=Mon Apr 06 12:43:03 GMT-04:00 2009

received-message-num=404194

sent-message-num=232248

sent-notifications-num=0

dropped-notifications-num=0

client-username=null