Table Of Contents

Raw Data Formatting: The RDR Formatter

Displaying Data Destination Configuration and Statistics

Displaying the Current RDR Formatter Configuration

Example

Displaying the Current RDR Formatter Statistics

Raw Data Formatting: The RDR Formatter

---

Cisco Service Control is able to deliver gathered reporting data to an external application for collecting, aggregation, storage and processing over the RDRv1 protocols: a proprietary export protocol. This module describes how to view configuration and statistics of the RDR formatter.

---

Note You should configuring the RDR formatter using the Application Performance Assurance Device Console. For further details, see the Cisco Application Performance Assurance Device Console User Guide.

---

---

Note The NME-APA CLI also contains commands to configure the RDR; however, these commands should be used only by a technician.

---

Displaying Data Destination Configuration and Statistics

The following commands can be used to display the RDR formatter configuration and statistics:

•show rdr-formatter

•show rdr-formatter connection-status

•show rdr-formatter counters

•show rdr-formatter destination

•show rdr-formatter enabled

•show rdr-formatter forwarding-mode

•show rdr-formatter rdr-mapping

•show rdr-formatter statistics

•show rdr-formatter protocol

See the Cisco Network Module Enhanced Application Performance Assurance CLI Command Reference for a complete description of the other show rdr-formatter commands.

Displaying the Current RDR Formatter Configuration

The system can display the complete data destination configuration, or just specific parameters.

---

Step 1 From the NME-APA> prompt, type show rdr-formatter and press Enter.

Displays the current RDR formatter configuration.

---

Example

The following example shows how to display the current RDR formatter configuration.

NME-APA#>show rdr-formatter 
Status: enabled 
Connection is: up 
Forwarding mode: multicast 
no destination is set for the RDR Formatter 
RDR:    queued:         7 ,sent:         0, thrown:         0 
UM:     queued:         0 ,sent:         0, thrown:         0 
Logger: queued:         0 ,sent:         0, thrown:         0 
Errors: thrown:         0 
Last time these counters were cleared: 17:41:26 UTC WED August 8 2007 
NME-APA#>

Displaying the Current RDR Formatter Statistics

---

Step 1 From the NME-APA>prompt, type show rdr-formatter statistics and press Enter.

Displays the current RDR formatter statistics.

---

Example

The following example shows how to display the current statistics in a deployment.

NME-APA#show rdr-formatter statistics                    
RDR-formatter statistics: 
========================= 
Category 1: 
sent:               1794517 
in-queue:           0 
thrown:             0 
format-mismatch:    0 
unsupported-tags:   1701243 
rate:               2 RDRs per second 
max-rate:           64 RDRs per second 
Category 2: 
sent:               12040436 
in-queue:           0 
thrown:             0 
format-mismatch:    0 
unsupported-tags:   0 
rate:               12 RDRs per second 
max-rate:           453 RDRs per second 
Category 3: 
sent:               0 
in-queue:           0 
thrown:             0 
format-mismatch:    0 
unsupported-tags:   0 
rate:               0 RDRs per second 
max-rate:           0 RDRs per second 
Category 4: 
sent:               0 
in-queue:           0 
thrown:             0 
format-mismatch:    0 
unsupported-tags:   0 
rate:               0 RDRs per second 
max-rate:           0 RDRs per second 
Destination:    10.56.201.50 Port: 33000 Status: up     
Sent:   13835366 
Rate:   211  Max:   679 
Last connection establishment:  17 hours, 5 minutes, 14 seconds 
Destination:     10.56.204.7 Port: 33000 Status: up     
Sent:   12134054 
Rate:   183  Max:   595 
Sent Templates:         13732 
Sent Data Records:   12134054 
Refresh Timeout (Sec):      5 
Last connection establishment:  17 hours, 5 minutes, 15 seconds