Table Of Contents

Mapping ACNS Software CLI Commands to the Content Distribution Manager GUI

Mapping ACNS Software CLI Commands to the Content Distribution Manager GUI

---

Table E-1 maps ACNS software CLI commands to the corresponding Content Distribution Manager GUI procedure. Software CLI commands are listed in alphabetical order in the first column. The second column indicates the GUI navigation path to the device group configuration window for each command. The third column provides a link to the GUI configuration procedure found elsewhere in this guide. In most cases, the procedure provides an illustration of the configuration window and a table at the end of the procedure that maps each field in the GUI window to its corresponding CLI command.

---

Note Most procedures in this guide document the configuration steps for individual devices, whereas this table provides the GUI navigation path to the device group configuration window, unless otherwise indicated. The procedures for configuring device groups and individual devices are the same, in most cases.

---

Table E-1 ACNS Software CLI to Content Distribution Manager GUI Map 

Command	GUI Navigation Path	Procedure Reference
acquirer proxy authentication outgoing ipaddress port_num username [password password] [ntlm domain [basic-auth-disable]]	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Connections	"Configuring Authentication for an HTTP Proxy Using the Content Distribution Manager GUI" section
acquirer proxy authentication transparent username [password password] [ntlm domain [basic-auth-disable]]	Devices > Device Groups > Prepositioning > Acquirer WCCP Proxy Authentication	Configuring Authentication for a WCCP Proxy Using the Content Distribution Manager GUI
asset tag name	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > Asset Tag	Configuring SNMP Asset Tag Settings
authentication {configuration | login} {local | radius | tacacs} enable primary [secondary | tertiary]	Devices > Device Groups > General Settings > Authentication > Login Authentication	Configuring Login Authentication and Configuration Authorization
authentication fail-over server-unreachable
bandwidth {real-proxy {incoming kbits | outgoing kbits} | real-server kbits | wmt {incoming kbits | outgoing kbits} | cisco-streaming-engine kbits | http kbits} {start-time weekday time end-time weekday time}	Devices > Device Groups > Streaming/Caching > Scheduled Bandwidth	Configuring Scheduled Bandwidth Settings
bandwidth {real-proxy {incoming kbits | outgoing kbits} | real-server kbits | wmt {incoming kbits | outgoing kbits } | cisco-streaming-engine kbits | http kbits} {default | max-bandwidth}	Devices > Device Groups > Streaming/Caching > Default and Maximum Bandwidth	Configuring Content Services Default and Maximum Bandwidth Settings
bitrate http default bitrate	Devices > Device Groups > Streaming/Caching > WMT > General Settings	Configuring WMT Proxy Settings
bitrate wmt incoming bitrate
bitrate wmt outgoing bitrate
bypass auth-traffic enable	Devices > Device Groups > Request Routing > WCCP > Bypass	Configuring WCCP Bypass Settings
bypass load {enable | in-interval seconds | out-interval seconds | time-interval minutes}
bypass static {clientip {serverip | any-server} | any-client serverip}	Devices > Device Groups > Request Routing > WCCP > Bypass List	Creating WCCP Bypass List Entries
bypass timer minutes	Devices > Device Groups > Request Routing > WCCP > Bypass	Configuring WCCP Bypass Settings
bypass gateway ipaddress
error-handling {reset-connection | send-cache-error | transparent}
cdp enable	Devices > Device Groups > General Settings > Network > CDP	Configuring CDP Settings
cdp holdtime seconds
cdp timer seconds
clock timezone timezone offset	Devices > Device Groups > General Settings > Time Zone	Configuring Device Clock and Time Zone Settings
clock summertime timezone {date | recurring}
dns min-ttl seconds	Devices > Device Groups > Request Routing > DNS Caching > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine
dns max-ttl seconds
dns user-expired enable
dns max-cache-memory mbytes	Devices > Device Groups > General Settings > Network > DNS	Configuring the Domain Name System Server
	Devices > Device Groups > Request Routing > DNS Caching > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine
dns enable	Devices > Device Groups > General Settings > Network > DNS	Configuring the Domain Name System Server
	Devices > Device Groups > Request Routing > DNS Caching > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine
dns listen {all | ipaddress} port port_num hostname hostname	Devices > Devices1 > Request Routing > DNS Caching > DNS Server Binding	Configuring DNS Server Bindings for the Content Engine
dns use-original-server {only | after-configured | before-configured}	Devices > Device Groups > Request Routing > DNS Caching > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine
dns pin {forward hostname ipaddress | reverse hostname ipaddress | both hostname ipaddress | cname records}	Devices > Device Groups > Request Routing > DNS Caching > A-Record Mapping	Configuring DNS Address Record Mappings for the Content Engine
	Devices > Device Groups > Request Routing > DNS Caching > CNAME Record Mapping	Configuring DNS Canonical Name Record Mappings for the Content Engine
dns retry-period seconds	Devices > Device Groups > Request Routing > DNS Caching > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine
dns retry-timeout seconds
dns serial-lookup	Devices > Device Groups > General Settings > Network > DNS	Configuring the Domain Name System Server
	Devices > Device Groups > Request Routing > DNS Caching > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine
exec-timeout minutes	Devices > Device Groups > General Settings > Network > Exec Timeout	Configuring Exec Timeout Settings
ftp age-multiplier directory-listing dl_time file fo_time	Devices > Device Groups > Streaming/Caching > FTP/TFTP > FTP Cache Freshness	Setting FTP Cache Freshness
ftp max-ttl {days directory-listing dlmax_days file fmax_days | hours directory-listing dlmax_hours file fmax_hours | minutes directory-listing dlmax_min file fmax_min | seconds directory-listing dlmax_sec file fmax_sec}
ftp min-ttl min_minutes
ftp object max-size size
ftp proxy incoming ports	Devices > Device Groups > Streaming/Caching > FTP/TFTP > FTP Connections	Configuring FTP Connection Settings
ftp proxy outgoing host {hostname | ipaddress} port
ftp proxy anonymous-pswd passwd
ftp proxy active-mode enable
ftp reval-each-request {all | none | directory-listing}	Devices > Device Groups > Streaming/Caching > FTP/TFTP > FTP Cache Freshness	Setting FTP Cache Freshness
gui-server enable	Devices > Device Groups > Request Processing > GUI Server	Configuring the Content Engine GUI for Secure or Nonsecure Access, page 12-38
gui-server secure enable
gui-server port port_num
gui-server secure port port_num
http add-method method	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Method	Adding or Modifying Additional HTTP Request Methods for the Content Engine
http age-multiplier text num binary num	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Cache Freshness	Configuring HTTP Cache Freshness Settings
http anonymizer enable	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Caching	Configuring HTTP Cache Settings
http append via-header	Devices > Device Groups > Streaming/Caching > HTTP > Authenticated HTTP Caching	Configuring Authenticated HTTP Cache Settings
http append host-header
http append x-forwarded-for-header
http append proxy-auth-header {ipaddress | hostname}
http append www-auth-header {hostname | ipaddress}
http authenticate-strip-ntlm
http authentication cache timeout minutes	Devices > Device Groups > Streaming/Caching > HTTP > Authenticated HTTP Caching	Configuring Authenticated HTTP Cache Settings
http authentication cache max-entries entries
http authentication header {401 | 407}
http authentication realm line
http cache-authenticated basic
http cache-authenticated ntlm
http cache-authenticated all
http cache-cookies	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Caching	Configuring HTTP Cache Settings
http cache-on-abort enable	Devices > Device Groups > Streaming/Caching > HTTP > Advanced HTTP Caching	Configuring Advanced HTTP Cache Settings
http cache-on-abort max-threshold max_thresh
http cache-on-abort min-threshold min_thresh
http cache-on-abort percent percenthresh
http cache-vary-user-agent enable	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Caching	Configuring HTTP Cache Settings
http client-no-cache-request {ignore | revalidate}
http cluster max-delay seconds	Devices > Device Groups > Streaming/Caching > HTTP > Advanced HTTP Caching	Configuring Advanced HTTP Cache Settings
http cluster misses num
http cluster http-port num
http cluster heal-port num
http dns-cache size max-num	Devices > Device Groups > Request Routing > DNS Caching > DNS Caching Server	Configuring DNS Caching Name Service for WCCP
http dns-cache serial-lookup
http fast-response enable	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Caching	Configuring HTTP Cache Settings
http l4-switch {enable | spoof-client-ip enable}
http max-ttl {days text textdays binary bindays | hours text texthours binary binhours | minutes text textminutes binary binminutes | seconds text textseconds binary binseconds}	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Cache Freshness	Configuring HTTP Cache Freshness Settings
http min-ttl minutes
http object max-size kbytes	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Caching	Configuring HTTP Cache Settings
http object url-validation enable
http persistent-connections [all | server-only | client-only]	Devices > Device Groups > Streaming/Caching > HTTP > Advanced HTTP Caching	Configuring Advanced HTTP Cache Settings
http persistent-connections timeout seconds
http proxy incoming ports	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Connections	Configuring HTTP Connection Settings
http proxy outgoing {connection-timeout microsecs | host {hostname | ipaddress} port [primary] | monitor seconds | origin-server | preserve-407}}
http request-header host unmodified	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Caching	Configuring HTTP Cache Settings
http reval-each-request all	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Cache Freshness	Configuring HTTP Cache Freshness Settings
http reval-each-request none
http reval-each-request text
http serve-ims text percentage binary percentage
http smart-range enable	Devices > Device Groups > Streaming/Caching > HTTP > HTTP Caching	Configuring HTTP Cache Settings
http smart-range max-start offset max-interval interval
http strict-request-content-length-checking enable
http tcp-keepalive enable	Devices > Device Groups > Streaming/Caching > HTTP > Advanced HTTP Caching	Configuring Advanced HTTP Cache Settings
https proxy incoming ports	Devices > Device Groups > Streaming/Caching > HTTPS > HTTPS Proxy	Configuring HTTPS Proxy Settings
https proxy outgoing host {ipaddress | hostname} port
https destination-port {allow | deny}{range | all}
https tcp-rw-timeout seconds
https server name	Devices > Device Groups > Streaming/Caching > HTTPS > HTTPS Servers	Configuring HTTPS Servers
https server name {cert cert_name | certgroup {chain chainname | serverauth chainname} | enable | host {hostname | ipaddress} | key keyname password password | protocol-version {sslv2-only | sslv23-tlsv1 | sslv3-only | tlsv1-only} | serverauth {enable | ignore {cert-not-yet-valid | domain-name | expired-date | invalid-ca}} | session-cache {size size | timeout timeout}}	Devices > Device Groups > Streaming/Caching > HTTPS > Certificates	Configuring HTTPS Certificates
	Devices > Device Groups > Streaming/Caching > HTTPS > Certificate Groups	Configuring HTTPS Certificate Groups
	Devices > Device Groups > Streaming/Caching > HTTPS > Keys	Configuring HTTPS Keys
icap append-x-headers {x-client-ip | x-server-ip}	Devices > Device Groups > Request Processing > ICAP	Configuring ICAP Settings, page 12-1
icap apply {all | rules-template}
icap bypass streaming-media
icap logging {format standard | enable}
icap rescan-cache ISTag-change
icap service service_id	Devices > Device Groups > Request Processing > ICAP Services	Configuring ICAP Services, page 12-4
ICAP service configuration mode (config-icap-service)# icap service service_id [enable | vector-point {reqmod-precache | reqmod-postcache | respmod-precache} | error-handling {bypass | return-error} | load-balancing {round-robin | client-ip-hash | server-ip-hash | weighted-load}]
ICAP service configuration mode (config-icap-service)# icap service server server server_url {max-connections num | weight num}	Devices > Device Groups > Request Processing > ICAP Services	Configuring an ICAP Server for ICAP Service, page 12-7
icp client add-remote-server {hostname | ipaddress} {parent | sibling} icp-port icpport http-port httpport [restrict domainnames]	Devices > Device Groups > Streaming/Caching > HTTP > ICP > Remote Servers	ICP Remote Server Settings
icp client enable	Devices > Device Groups > Streaming/Caching > HTTP > ICP > Client	ICP Client Settings
icp client exclude domainnames
icp client max-fail retries
icp client max-wait timeout
icp client modify-remote-server {hostname | ipaddress} {http-port port | icp-port port | parent | restrict domainnames | sibling}	Devices > Device Groups > Streaming/Caching > HTTP > ICP > ICP Remote Servers	ICP Remote Server Settings
icp server enable	Devices > Device Groups > Streaming/Caching > HTTP > ICP > Server	ICP Server Settings
icp server http-port httpport
icp server port icpport
icp server remote-client {hostname | ipaddress} {fetch | no-fetch}	Devices > Device Groups > Streaming/Caching > HTTP > ICP > Remote Clients	ICP Remote Client Settings
inetd enable ftp	Devices > Device Groups > Streaming/Caching > FTP/TFTP > FTP Connections	Configuring FTP Connection Settings
inetd enable tftp	Devices > Device Groups > Streaming/Caching > FTP/TFTP > TFTP General Settings	Configuring TFTP General Settings
inetd enable rcp	Devices > Device Groups > General Settings > Network > Inetd RCP	Enabling RCP Services on the Content Engine
interface {FastEthernet | GigabitEthernet} slot/port cdp enable	Devices > Devices1 > General Settings > Network > Network Interfaces	Modifying Fast Ethernet or Gigabit Ethernet Interface Settings
interface {FastEthernet | GigabitEthernet} slot/port shutdown
interface {FastEthernet | GigabitEthernet} slot/port autosense
interface {FastEthernet | GigabitEthernet} slot/port bandwidth {10 | 100 | 1000}
interface {FastEthernet | GigabitEthernet} slot/port [full-duplex | half-duplex]
interface {FastEthernet | GigabitEthernet} slot/port mtu size
interface {FastEthernet | GigabitEthernet} slot/port ip address ipaddress netmask [secondary]
interface {FastEthernet | GigbitEthernet} slot/port standby groupnum ip ipaddress netmask	Devices > Devices1> General Settings > Network > Network Interfaces	Configuring a Standby Interface Using the Content Distribution Manager GUI
interface {FastEthernet | GigbitEthernet} slot/port standby groupnum errors num
interface {FastEthernet | GigbitEthernet} slot/port standby groupnum priority priority	Devices > Devices1 > General Settings > Network > Network Interfaces	Configuring the Interface Priority Setting
interface {FastEthernet | GigabitEthernet} slot/port ip address dhcp {client-id id hostname name | hostname name client-id id}		Configuring Interfaces for DHCP
interface FibreChannel slot/port [mode {autosense | direct-attached | switched} | speed {1 | 2 | autosense}]		Configuring the Fibre Channel Interface
interface PortChannel {1 | 2} [ip address ipaddress netmask | shutdown]	Devices > Devices1 > General Settings > Network > Network Interfaces	Configuring EtherChannel
interface {FastEthernet | GigabitEthernet} slot/port ip access-group {accesslistnumber | accesslistname} {in | out}	Devices > Devices1 > General Settings > Network > Network Interfaces	Applying an IP ACL to an Interface
ip access-list {standard | extended} {acl_name | acl_num} Includes other configuration commands for standard and extended IP ACLs.	Devices > Devices1 > General Settings > Network > IP ACL	Creating or Modifying an IP ACL
Extended ACL configuration mode (config-ext-nacl)# [insert line_num] {deny | permit}{gre | ip | proto_num} {source_ip [wildcard] | host source_ip | any} {dest_ip [wildcard] | host dest_ip | any} [insert line_num] {deny | permit} tcp {source_ip [wildcard] | host source_ip | any} [operator port [port]] {dest_ip [wildcard] | host dest_ip | any} [operator port [port]] [established] [insert line_num] {deny | permit} udp {source_ip [wildcard] | host source_ip | any} [operator port [port]] {dest_ip [wildcard] | host dest_ip | any} [operator port [port]] [insert line_num] {deny | permit} icmp {source_ip [wildcard] | host source_ip | any} {dest_ip [wildcard] | host dest_ip | any} [icmp_type [code] | icmp_msg] delete line_num | list [start_line_num [end_line_num]] | move oldline_num newline_num | exit	Devices > Devices1 > General Settings > Network > IP ACL	Adding Conditions to an IP ACL
Standard ACL configuration mode (config-std-nacl)# [insert line_num] {deny | permit} {source_ip [wildcard] | host source_ip | any} delete line_num | list [start_line_num [end_line_num]] | move oldline_num newline_num | exit	Devices > Devices1 > General Settings > Network > IP ACL	Adding Conditions to an IP ACL
ip default-gateway ipaddress	Devices > Devices1 > General Settings > Network > Network Interfaces	Configuring a Standby Interface Using the Content Distribution Manager GUI
		Modifying Fast Ethernet or Gigabit Ethernet Interface Settings
ip domain-name name1 name2 name3	Devices > Device Groups > General Settings > Network > DNS	Configuring the Domain Name System Server
ip name-server ipaddress
ldap server allow-mode	Devices > Device Groups > General Settings > Authentication > LDAP Server	Configuring LDAP Server Settings
ldap server group active-directory enable
ldap server base baseword
ldap server enable	Devices > Device Groups > General Settings > Authentication > Authentication Scheme	Setting the Authentication Scheme for Request Authentication
ldap server filter filterword	Devices > Device Groups > General Settings > Authentication > LDAP Server	Configuring LDAP Server Settings
ldap server host {hostipaddress | hostname} [primary | secondary]
ldap server port port_num
ldap server retransmit retries
ldap server timeout seconds
ldap server userid-attribute useridword
ldap server administrative-dn name
ldap server administrative-passwd passwd
ldap server version ver_num
logging host {ipaddress | hostname}	Devices > Device Groups > General Settings > Notification and Tracking > System Logs	Configuring System Event Logging Using the Content Distribution Manager GUI
logging host priority {alert | critical | debug | emergency | error | information | notice | warning}
logging disk enable
logging disk filename filename
logging disk recycle size
logging disk priority {alert | critical | debug | emergency | error | information | notice | warning}
logging console enable
logging console priority {alert | critical | debug | emergency | error | information | notice | warning}
logging facility {auth | daemon | kernel | local0 | local1 | local2 | local3 | local4 | local5 | local6 | local7 | mail | news | syslog | user | uucp}
multicast license-key key	Devices > Device Groups > Prepositioning > Multicast Distribution License	Enabling Content Engines for Multicasting
multicast accept-license-agreement multicast enable
multicast evaluate
network-filesystem server {samba | cifs} {enable | authentication-mode {public | ce-user | cifs-user | password-server} | max-connections num}	Devices > Device Groups > General Settings > File Sharing > CIFS Server	Configuring CIFS Server Settings
network-filesystem server {samba | cifs} {share-web-site site_name [share-auth-content | protect-auth-content]}	Devices > Device Groups > General Settings > File Sharing > CIFS Server Access Control	Configuring CIFS Server Website Access Control Settings
network-filesystem client {cifs {hostname | ipaddress} directory {cdnfs | mediafs} reserved-disk-space space username name password password [domain domain] | nfs {hostname | ipaddress} directory {cdnfs | mediafs} reserved-disk-space space}	Devices > Devices1 > General Settings > Storage > NAS	Attaching and Detaching NAS Shares Using the Content Distribution Manager GUI
ntlm server enable	Devices > Device Groups > General Settings > Authentication > Authentication Scheme	Setting the Authentication Scheme for Request Authentication
ntlm server host {hostname | ipaddress}	Devices > Device Groups > General Settings > Authentication > NTLM Server	Configuring NTLM Server Settings
ntlm server domain name
ntp server {hostname | ipaddress}	Devices > Device Groups > General Settings > Network > NTP	Configuring NTP Settings
port-channel load-balance {dst-ip | dst-mac | round-robin}	Devices > Devices1 > General Settings > Network > Network Interfaces	Configuring EtherChannel
proxy-auto-config enable	Devices > Device Groups > Streaming/Caching > Client Proxy Autoconfiguration	Configuring Client Proxy Autoconfiguration Settings
proxy-protocols outgoing-proxy exclude {enable | list word}	Devices > Device Groups > Streaming/Caching > Outgoing Proxy Exclusions	Configuring HTTP and HTTPS Outgoing Proxy Exclusion Settings
proxy-protocols transparent {default-server | original-proxy | reset}
radius-server key key	Devices > Device Groups > General Settings > Authentication > RADIUS Server	Configuring RADIUS Server Settings
radius-server timeout seconds
radius-server enable	Devices > Device Groups > General Settings > Authentication > Authentication Scheme	Setting the Authentication Scheme for Request Authentication
radius-server host {hostname | ipaddress} {auth-port port}	Devices > Device Groups > General Settings > Authentication > RADIUS Server	Configuring RADIUS Server Settings
radius-server retransmit retries
radius-server redirect enable
radius-server redirect message reply location url
rtsp advanced max-initial-setup-delay seconds	Devices > Device Groups > Streaming/Caching > RTSP Gateway	Configuring the RTSP Gateway
rtsp advanced max-request-rate number
rtsp proxy media-real enable	Devices > Device Groups > Streaming/Caching > Real Networks > Real Proxy License	Enabling RealProxy
rtsp proxy media-real evaluate
rtsp proxy media-real license-key key
rtsp proxy media-real accept-license-agreement
rtsp server real-subscriber license-key key	Devices > Device Groups > Streaming/Caching > Real Networks > Real Subscriber License	Enabling RealSubscriber
rtsp server real-subscriber accept-license-agreement
rtsp server real-subscriber evaluate
rtsp server real-subscriber enable
rtsp l4-switch enable	Devices > Device Groups > Streaming/Caching > RTSP Gateway	Configuring the RTSP Gateway
rtsp port incoming port_num
rtsp ip-address ipaddress
rtsp server cisco-streaming-engine enable	Devices > Device Groups > Streaming/Caching > Cisco Streaming Engine	Enabling the Cisco Streaming Engine
rtsp server cisco-streaming-engine broadcast port-list list_num port_num	Content > Programs > Live Streaming (indirect support)	Configuring Live Stream Settings for a Cisco Streaming Engine Live Program
rtsp server cisco-streaming-engine broadcast id id source {source-rtsp rtsp_url | source-udp url srce_ip_addr recv_ip_addr recv_port_list_num } {track-count 1-4} destination {destination-pull | destination-udp ttl dest_ip_addr dest_list_num}
rule enable	Devices > Device Groups > Request Processing > Enable Rules	Enabling Rule Settings, page 12-10
rule action rule action allow pattern-list list_num [protocol {all | http | https | mms | rtsp}] rule action append-username-header pattern-list list_num [protocol {all | http | https | mms | rtsp}] rule action block pattern-list list_num [protocol {all | http | https | mms | rtsp}] rule action cache-non-cacheable ttl {day days pattern-list list_num [protocol {all | http | https}] | hours hours pattern-list list_num [protocol {all | http | https}] | minutes minutes pattern-list list_num [protocol {all | http | https}] | seconds seconds pattern-list list_num [protocol {all | http | https}]}	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 12-10
rule action cache-only pattern-list list_num [protocol {all | http | https | mms}] rule action dscp client cache-hit {match-server pattern-list list_num [protocol {all | http | https}] | set-dscp dscpvalue | set-tos tosvalue} rule action dscp client cache-miss {match-server pattern-list list_num [protocol {all | http | https}] | set-dscp dscpvalue | set-tos tosvalue}} rule action dscp server {match-client pattern-list list_num [protocol {all | http | https}] | set-dscp dscpvalue | set-tos tosvalue}	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 12-10
rule action freshness-factor exp_time pattern-list list_num [protocol {all | http | https}] rule action insert-no-cache pattern-list list_num [protocol {all | http | https}] rule action no-auth pattern-list list_num [protocol {all | http | https | mms | rtsp}] rule action no-cache pattern-list list_num [protocol {all | http | https | mms}] rule action no-persistent-connection {all | client | server} pattern-list list_num [protocol {all | http | https}]	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 12-10
rule action no-proxy pattern-list list_num [protocol {all | http | https}] rule action redirect url pattern-list list_num [protocol {all | http | https | rtsp}] rule action redirect-url-for-cdn pattern-list list_num [protocol {all | http | https | rtsp}] rule action refresh pattern-list list_num [protocol {all | http | https}] rule action reset pattern-list list_num [protocol {all | http | https | mms | rtsp}] rule action rewrite pattern-list list_num [protocol {all | http | https | mms | rtsp}]	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 12-10
rule action use-dns-server {hostname | ipaddress} pattern-list list_num [protocol {all | http | https}] rule action use-icap-service service_name pattern-list list_num [protocol {all | http | https | mms}] rule action use-proxy {hostname | ipaddress} port pattern-list list_num [protocol {all | http | https}] rule action use-proxy {hostname | ipaddress} port [failover] pattern-list list_num [protocol {all | http | https}] rule action use-server {hostname | ipaddress} port pattern-list list_num [protocol {all | http | https}] rule action use-xforward-clt-ip pattern-list list_num [protocol {all | http | https}]	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 12-10
rule pattern-list list_num domain dn_regexp rule pattern-list list_num dst-ip d_ipaddress d_subnet rule pattern-list list_num dst-port port rule pattern-list list_num groupname name rule pattern-list list_num groupname-regex group_name_regexp rule pattern-list list_num group-type {and | or} rule pattern-list list_num header-field {referer ref_regexp | request-line req_regexp | user-agent ua_regexp} rule pattern-list list_num header-field-sub {referer ref_regexp ref_sub | request-line req_regexp req_sub | user-agent ua_regexp ua_sub}	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 12-10
rule pattern-list list_num icap-attribute icap_attribute icap_value rule pattern-list list_num mime-type mt_regexp rule pattern-list list_num src-ip s_ipaddress s_subnet rule pattern-list list_num url-regex url_regexp rule pattern-list list_num url-regsub url_regexp url_sub rule pattern-list list_num username user_name	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 12-10
snmp-server contact line	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > General Settings	Configuring SNMP General Settings
snmp-server enable traps [config | content-engine [disk-fail | disk-read | disk-write | overload-bypass | transaction-log] | entity | event | snmp [authentication | cold-start]]
snmp-server host {hostname | ipaddress} communitystring [v2c [retry num] [timeout seconds]] | [v3 {auth [retry num] [timeout seconds] | noauth [retry num] [timeout seconds] | priv [retry num] [timeout seconds]}]	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > Host	Configuring SNMP Host Settings
snmp-server location line	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > General Settings	Configuring SNMP General Settings
snmp-server user name group [auth {md5 password [priv password] | sha password [priv password]} | remote octetstring [auth {md5 password [priv password] | sha password [priv password]}]]	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > User	Configuring SNMP User Settings
snmp-server group name {v1 [notify name] [read name] [write name] | v2c [notify name] [read name] [write name] | v3 {auth [notify name] [read name] [write name] | noauth [notify name] [read name] [write name] | priv [notify name] [read name] [write name]}}	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > Group	Configuring SNMP Group Settings
snmp-server community string [group groupname | rw]	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > Community	Configuring SNMP Community Settings
snmp-server view viewname MIBfamily {excluded | included}	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > View	Configuring SNMPv2 View Settings
snmp-server notify inform	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > General Settings	Configuring SNMP General Settings
snmp-server mib persist event
snmp-server access-list {std_acl_number | acl_name}	Devices > Devices1 > General Settings > Network > IP ACL Feature Usage	Associating an IP ACL with an Application
sshd enable	Devices > Device Groups > General Settings > Network > SSH	Configuring Secure Shell Settings
sshd timeout seconds
sshd password-guesses num
ssh-key-generate key-length length
tacacs enable	Devices > Device Groups > General Settings > Authentication > TACACS+ Server	Configuring TACACS+ Server Settings
tacacs password ascii
tacacs timeout
tacacs retransmit
tacacs key
tacacs host {ipaddress | hostname} [primary]
tcp ecn enable	Devices > Device Groups > General Settings > Network > TCP	Configuring TCP Settings
tcp type-of-service enable
tcp cwnd-base segments
tcp increase-xmit-timer-value value
tcp init-ss-threshold value
tcp keepalive-probe-cnt count
tcp keepalive-probe-interval seconds
tcp keepalive-timeout seconds
tcp client-satellite
tcp client-mss max_seg_size
tcp client-receive-buffer kbytes
tcp client-rw-timeout seconds
tcp client-send-buffer kbytes
tcp server-satellite
tcp server-mss max_seg_size
tcp server-receive-buffer kbytes
tcp server-rw-timeout seconds
tcp server-send-buffer kbytes
telnet enable	Devices > Device Groups > General Settings > Network > Telnet	Enabling the Telnet Service on the Content Engine
tftp-server dir directory	Devices > Device Groups > Streaming/Caching > FTP/TFTP > TFTP Directory	Configuring TFTP Directory Settings
tftp-server access-list {std_acl_number | acl_name}	Devices > Devices1 > General Settings > Network > IP ACL Feature Usage	Associating an IP ACL with an Application
tftp-server gw proto {http | ftp} server {hostname | ipaddress} pri priority [name name passwd password] [path directory]	Devices > Device Groups > Streaming/Caching > FTP/TFTP > TFTP Proxy	Configuring TFTP Proxy Server Settings
transaction-logs archive max-file-size kbytes	Devices > Device Groups > General Settings > Notification and Tracking > Transaction Logs	Enabling Transaction Logging with the Content Distribution Manager GUI
transaction-logs archive interval {seconds | every-week [on weekdays at hour:minute] | every-day {at hour:minute | every hours} | every-hour {at minute | every minutes}
transaction-logs enable
transaction-logs export enable
transaction-logs export ftp-server {hostname | ipaddress} login password directory
transaction-logs export sftp-server {hostname | ipaddress} login password directory
transaction-logs export compress	Devices > Device Groups > General Settings > Notification and Tracking > Transaction Logs	Enabling Transaction Logging with the Content Distribution Manager GUI
transaction-logs export interval {minutes | every-week [on weekdays at hour:minute] | every-day {at hour:minute | every hours} | every-hour {at minute | every minutes}
transaction-logs file-marker
transaction-logs sanitize
transaction-logs log-windows-domain
transaction-logs format {squid | extended-squid | apache | custom string}
tvout signal {ntsc | pal }	Devices > Device Groups > Streaming/Caching > TV-out	Enabling the TV-Out Feature
tvout enable
url-filter http {bad-sites-deny | good-sites-allow} {enable | file filename}	Devices > Device Groups > Request Processing > URL Filter > HTTP > URL Filter Settings for HTTP Protocol	Configuring URL Filter Settings Using the Content Distribution Manager GUI, page 12-22
url-filter http websense allowmode enable		URL Filtering with Websense Enterprise Software, page 12-31
url-filter http websense enable
url-filter http websense server {ipaddress | hostname} port 1-65535 timeout seconds connections 1-250
url-filter http N2H2 allowmode enable		URL Filtering with the N2H2 Server, page 12-26
url-filter http N2H2 enable
url-filter http N2H2 server {ipaddress | hostname} port 1-65535 timeout
url-filter http smartfilter enable		URL Filtering with SmartFilter Software, page 12-38
url-filter http custom-message dirname	N/A	Custom Blocking Messages, page 12-21
url-filter wmt {bad-sites-deny | good-sites-allow} {enable | file filename }	Devices > Device Groups > Request Processing > URL Filter > WMT > URL Filter Settings for WMT Protocol	Configuring URL Filter Settings Using the Content Distribution Manager GUI, page 12-22
url-filter rtsp {bad-sites-deny | good-sites-allow} {enable | file filename }	Devices > Device Groups > Request Processing > URL Filter > RTSP > URL Filter Settings for RTSP Protocol	Configuring URL Filter Settings Using the Content Distribution Manager GUI, page 12-22
wccp access-list {std_acl_number | ext_acl_number | acl_name}	Devices > Devices1 > General Settings > Network > IP ACL Feature Usage	Associating an IP ACL with an Application
wccp custom-web-cache mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine
wccp custom-web-cache router-list-num num port port [assign-method-strict] [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine
wccp dns mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine
wccp dns router-list-num num [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine
wccp flow-redirect enable	Devices > Device Groups > Request Routing > WCCP > General Settings	Configuring WCCP General Settings for the Content Engine
wccp ftp router-list-num num [assign-method-strict] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine
wccp ftp mask {[dst-ip-mask hex_num] [src-ip-mask hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine
wccp home-router ipaddress	Devices > Device Groups > Request Routing > WCCP > General Settings	Configuring WCCP General Settings for the Content Engine
wccp https-cache accept-all
wccp https-cache mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine
wccp https-cache router-list-num num port port [assign-method-strict] [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine
wccp port-list list_num port_num	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Port Lists for the Content Engine
wccp rtsp mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine
wccp rtsp router-list-num num [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine
wccp reverse-proxy mask [dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine
wccp reverse-proxy router-list-num num [assign-method-strict] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine
wccp router-list list_num ipaddress	Devices > Device Groups > Request Routing > WCCP > Services	Creating WCCP Router Lists
wccp service-number service_num router-list-num num port-list-num port application {cache | streaming} [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [match-source-port] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine
wccp service-number service_num mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine
wccp shutdown max-wait seconds	Devices > Device Groups > Request Routing > WCCP > General Settings	Configuring WCCP General Settings for the Content Engine
wccp slow-start enable
wccp spoof-client-ip enable
wccp version {1 | 2}
wccp web-cache mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine
wccp web-cache router-list-num num [assign-method-strict] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine
wccp wmt mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Servicesk	Configuring WCCP Service Masks for the Content Engine
wccp wmt router-list-num num [assign-method-strict] [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine
websense-server enable	Devices > Device Groups > Request Processing > URL Filter > HTTP > URL Filter Settings for HTTP Protocol	Configuring URL Filter Settings Using the Content Distribution Manager GUI, page 12-22
wmt accept-license-agreement	Devices > Device Groups > Streaming/Caching > WMT > License	Enabling WMT
wmt bandwidth incoming bypass-list {ipaddress | hostname} [ipaddress | hostname]	Devices > Devices1 > Streaming/Caching > Local Content Services	Configuring the WMT Incoming Bandwidth Bypass List
wmt broadcast {alias-name name source url}	Devices > Device Groups > Streaming/Caching > WMT > Broadcast Alias	Configuring Multicast-In Unicast-Out Configuring Unicast-In Unicast-Out
wmt cache enable	Devices > Device Groups > Streaming/Caching > WMT > License	Enabling WMT
wmt cache max-obj-size mbytes	Devices > Device Groups > Streaming/Caching > WMT > General Settings	Configuring WMT Proxy Settings
wmt cache unique-stream-key	Devices > Device Groups > Streaming/Caching > WMT > License	Enabling WMT
wmt disallowed-client-protocols {HTTP [TCP | UDP] | TCP [HTTP | UDP] | UDP [HTTP | TCP]}
wmt enable
wmt evaluate
wmt extended transaction-log enable	Devices > Device Groups > General Settings > Notification and Tracking > Transaction Logs	Using WMT Transaction Logging
wmt accelerate live-split enable	Devices > Device Groups > Streaming/Caching > WMT > General Settings	Configuring WMT Proxy Settings
wmt accelerate proxy-cache enable
wmt fast-cache enable
wmt fast-start enable
wmt http allow extension file_extensions
wmt incoming port_num
wmt l4-switch enable
wmt license-key key	Devices > Device Groups > Streaming/Caching > WMT > License	Enabling WMT
wmt live-url-stripping enable	Devices > Device Groups > Streaming/Caching > WMT > General Settings	Configuring WMT Proxy Settings
wmt multicast station-configuration name dest_addr dest_port media_source [log {local | webserver webserver_url}] [play-forever] [unicast-url url]	Devices > Device Groups > Streaming/Caching > WMT > Multicast Stations	Configuring Unicast-In Multicast-Out Configuring Multicast-In Multicast-Out
wmt max-concurrent-sessions num	Devices > Device Groups > Streaming/Caching > WMT > General Settings	Configuring WMT Proxy Settings
wmt multicast schedule-start name minute hour day month	Devices > Device Groups > Streaming/Caching > WMT > Multicast Station Schedules	Configuring WMT Station Schedules
wmt multicast time-to-live ttl	Devices > Device Groups > Streaming/Caching > WMT > General Settings	Configuring WMT Proxy Settings
wmt proxy outgoing http host {hostname | ipaddress} port
wmt proxy outgoing mms host {hostname | ipaddress} port
wmt transaction-logs format {extended {wms-41 | wms-90} | wms-41 | wms-90}	Devices > Device Groups > General Settings > Notification and Tracking > Transaction Logs	Using WMT Transaction Logging

1 This command can only be configured on individual devices; the Content Distribution Manager GUI does not support this command for device group configuration.