Table Of Contents

FT Track Host Configuration Mode Commands

(config-ft-track-host) peer priority

(config-ft-track-host) peer probe

(config-ft-track-host) peer track-host

(config-ft-track-host) priority

(config-ft-track-host) probe

(config-ft-track-host) track-host

FT Track Interface Configuration Mode Commands

(config-ft-track-interface) peer priority

(config-ft-track-interface) peer track-interface vlan

(config-ft-track-interface) priority

(config-ft-track-interface) track-interface vlan

FT Track Host Configuration Mode Commands

Fault-tolerant (FT) track host configuration mode commands allow you to configure tracking and failure detection for critical network gateways and hosts.

To create a process that tracks and detects failures for a gateway or host and accesses FT track host configuration mode, use the ft track host command in configuration mode. The CLI prompt changes to (config-ft-track-host). For information about the commands in FT track host configuration mode, see the following commands.

Use the no form of this command to delete a process that tracks and detects failures for a gateway or host.

ft track host name

no ft track host name

Syntax Description

name	Unique identifier of the tracking process for a gateway or a host. Enter an unquoted text string with no spaces and a maximum of 64 alphanumeric characters.

Command Modes

Configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

The commands in this mode require the fault-tolerant feature in your user role. For details about role-based access control (RBAC) and user roles, see the Cisco 4700 Series Application Control Engine Appliance Virtualization Configuration Guide.

Examples

To create a process that tracks and detects failures for a gateway or host and accesses FT track host configuration mode, enter:

host1/Admin(config)# ft track host TRACK_GATEWAY1

host1/Admin(config-ft-track-host)#

To delete the process that tracks and detects failures for a gateway or host, enter:

host1/Admin(config)# no ft track host TRACK_GATEWAY1

Related Commands

show ft
show running-config

(config-ft-track-host) peer priority

To assign a priority for multiple probes on the standby member of a fault-tolerant (FT) group, use the peer priority command. Use the no form of this command to reset the multiple-probe priority to the default value of 10 on the standby member.

peer priority number

no peer priority number

Syntax Description

number

Priority of the probes configured for the gateway or host on the standby member. Enter a priority value as an integer from 0 to 255. The default is 0. Higher values indicate higher priorities.

Command Modes

FT track host configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

The peer command keyword indicates the standby member of an FT group.

Assign a priority value to multiple probes based on the relative importance of the gateway or host that the probes are tracking. If all the probes go down, the ACE decrements the priority of the FT group on the standby member by the value of the number argument. If the priority of the FT group on the active member falls below the priority of the FT group on the standby member, a switchover occurs where the active member becomes the standby member and the standby member becomes the active member.

Examples

To assign a priority for multiple probes on the standby member of an FT group, enter:

host1/Admin(config-ft-track-host)# peer priority 50

To reset the priority of multiple probes on the standby member of an FT group to the default value of 0, enter:

host1/Admin(config-ft-track-host)# no peer priority 50

Related Commands

(config-ft-track-host) priority

(config-ft-track-host) peer probe

To associate an existing probe with a gateway or host for tracking by the standby member of a fault-tolerant (FT) group, use the peer probe command. Use the no form of this command to dissociate the tracking probe from the tracking process on the standby member.

peer probe name priority number

no peer probe name priority number

Syntax Description

name	Identifier of an existing probe that you want to associate with a gateway or host for tracking.
priority number	(Optional) Specifies the priority of the probe. Enter an integer from 0 to 255. The default is 0. Higher values indicate higher priorities.

Command Modes

FT track host configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

The peer command keyword indicates the standby member of an FT group.

Assign a priority value to the probe based on the relative importance of the gateway or host that the probe is tracking. If the probe goes down, the ACE decrements the priority of the FT group on the standby member by the value of the number argument. If the priority of the FT group on the active member falls below the priority of the FT group on the standby member, a switchover occurs where the active member becomes the standby member and the standby member becomes the active member.

Examples

To configure a probe with priority of 15 on the standby member of an FT group, enter:

host1/Admin(config-ft-track-host)# peer probe TCP_PROBE1 priority 15

To remove the tracking probe from the standby member, enter:

host1/Admin(config-ft-track-host)# no peer probe TCP_PROBE1

Related Commands

show probe
show running-config
(config) ft peer
(config) probe
(config-ft-track-host) probe

(config-ft-track-host) peer track-host

To configure the IP address of the gateway or host that you want to track on the standby member of a fault-tolerant (FT) group, use the peer track-host command. Use the no form of this command to remove the IP address of the gateway or host from the tracking process on the standby member configuration.

peer track-host ip_address

no peer track-host ip_address

Syntax Description

ip_address

IP address of the gateway or host that you want the standby FT group member to track. Enter the IP address in dotted-decimal notation (for example, 172.16.27.1).

Command Modes

FT track host configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

The peer command keyword indicates the standby member of an FT group.

Examples

To configure the IP address of a gateway for tracking on the standby member of an FT group, enter:

host1/Admin(config-ft-track-host)# peer track-host 172.16.27.1

To remove the IP address of the tracked gateway from the standby member, enter:

host1/Admin(config-ft-track-host)# no peer track-host 172.16.27.1

Related Commands

show running-config
(config) ft peer
(config-ft-track-host) track-host

(config-ft-track-host) priority

To assign a priority for multiple probes on the active member of a fault-tolerant (FT) group, use the priority command. Use the no form of this command to reset the multiple-probe priority to the default value of 10 on the active member.

priority number

no priority number

Syntax Description

number

Priority of the probes configured for the gateway or host on the active member. Enter a priority value as an integer from 0 to 255. The default is 0. Higher values indicate higher priorities.

Command Modes

FT track host configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

Assign a priority value for multiple probes based on the relative importance of the gateway or host that the probes are tracking. If all the probes go down, the ACE decrements the priority of the FT group on the active member by the value of the number argument. If the priority of the FT group on the active member falls below the priority of the FT group on the standby member, a switchover occurs where the active member becomes the standby member and the standby member becomes the active member.

Examples

To assign a priority for multiple probes on the active member of an FT group, enter:

host1/Admin(config-ft-track-host)# priority 100

To reset the priority of multiple probes on the active member of an FT group to the default value of 0, enter:

host1/Admin(config-ft-track-host)# no priority 100

Related Commands

(config-ft-track-host) peer priority

(config-ft-track-host) probe

To associate an existing probe with a gateway or host for tracking by the active member of a fault-tolerant (FT) group, use the probe command. Use the no form of this command to dissociate the tracking probe from the tracking process on the active member.

probe name priority number

no probe name priority number

Syntax Description

name	Identifier of an existing probe that you want to associate with a gateway or host for tracking.
priority number	(Optional) Specifies the priority of the probe on the active member of an FT group. Enter an integer from 0 to 255. The default is 0. Higher values indicate higher priorities.

Command Modes

FT track host configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

Assign a priority value to the probe based on the relative importance of the gateway or host that the probe is tracking. If the probe goes down, the ACE decrements the priority of the FT group on the active member by the value of the number argument. If the priority of the FT group on the active member falls below the priority of the FT group on the standby member, a switchover occurs where the active member becomes the standby member and the standby member becomes the active member.

Examples

To configure a probe with a priority of 25 on the active member of an FT group, enter:

host1/Admin(config-ft-track-host)# probe TCP_PROBE1 priority 25

To remove the tracking probe from the active member, enter:

host1/Admin(config-ft-track-host)# no probe TCP_PROBE1

Related Commands

show probe
show running-config
(config) probe
(config-ft-track-host) peer probe

(config-ft-track-host) track-host

To configure the IP address of the gateway or host that you want to track on the active member of a fault-tolerant (FT) group, use the track-host command. Use the no form of this command to remove the IP address of the gateway or host from the tracking process on the active member.

track-host ip_address

no track-host ip_address

Syntax Description

ip_address

IP address of the gateway or host that you want the active FT group member to track. Enter the IP address in dotted-decimal notation (for example, 172.16.27.1).

Command Modes

FT track host configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

This command has no usage guidelines.

Examples

To configure a gateway for tracking on the active member of an FT group, enter:

host1/Admin(config-ft-track-host)# track-host 172.16.27.1

To remove the gateway from the tracking process on the active member, enter:

host1/Admin(config-ft-track-host)# no track-host 172.16.27.1

Related Commands

show running-config
(config-ft-track-host) peer track-host

FT Track Interface Configuration Mode Commands

Fault-tolerant (FT) track interface configuration mode allows you to configure tracking and failure detection for critical interfaces.

To create a process that tracks and detects failures for critical interfaces and accesses FT track interface configuration mode, enter the ft track interface command in configuration mode. The CLI prompt changes to (config-ft-track-interface). For information about the commands in FT track interface configuration mode, see the following commands.

To delete the process that tracks and detects failures for an interface, use the no form of this command.

ft track interface name

no ft track interface name

Syntax Description

name	Unique identifier of the process that tracks and detects failures for a critical interface. Enter an unquoted text string with no spaces and a maximum of 64 alphanumeric characters.

Command Modes

Configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

The commands in this mode require the fault-tolerant feature in your user role. For details about role-based access control (RBAC) and user roles, see the Cisco 4700 Series Application Control Engine Appliance Virtualization Configuration Guide.

Examples

To create a process that tracks and detects failures for an interface and access FT track interface configuration mode, enter:

host1/Admin(config)# ft track interface TRACK_VLAN200

host1/Admin(config-ft-track-interface)#

To delete the process that tracks and detects failures for an interface, enter:

host1/Admin(config)# no ft track interface TRACK_VLAN200

Related Commands

show running-config

(config-ft-track-interface) peer priority

To assign a priority to the interface that the standby member is tracking, use the peer priority command. Use the no form of this command to reset the priority to the default value of 10.

peer priority number

no peer priority number

Syntax Description

number

Priority of the interface tracked by the standby member of a fault-tolerant (FT) group. Enter an integer from 0 to 255. The default is 0. Higher values indicate higher priorities.

Command Modes

FT track interface configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

The peer command keyword indicates the standby member of an FT group.

Assign a priority value based on the relative importance of the interface that you are tracking on the standby member of an FT group. If the tracked interface goes down, the ACE decrements the priority of the FT group on the standby member by the value of the number argument. If the priority of the FT group on the active member falls below the priority of the FT group on the standby member, a switchover occurs where the active member becomes the standby member and the standby member becomes the active member.

Examples

To set a priority of 100 for the interface that you are tracking on the standby member, enter:

host1/Admin(config-ft-track-intf)# peer priority 100

To reset the priority of the interface to the default value of 0, enter:

host1/Admin(config-ft-track-intf)# no peer priority 100

Related Commands

(config-ft-track-interface) priority

(config-ft-track-interface) peer track-interface vlan

To configure the interface that you want the standby member to track, use the peer track-interface vlan command. Use the no form of this command to remove the interface.

peer track-interface vlan vlan_id

no peer track-interface vlan vlan_id

Syntax Description

vlan_id

Unique identifier of an existing VLAN that you want to track on the standby member of a fault-tolerant (FT) group. Enter an integer from 2 to 4094.

Command Modes

FT track interface configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

The peer command keyword indicates the standby member of an FT group.

You cannot track the FT VLAN because it is reserved for the redundancy protocol.

Examples

To configure the VLAN 200 interface for tracking on the standby member, enter:

host1/Admin(config-ft-track-intf)# peer track-interface vlan 200

To remove VLAN 200 from the tracking process, enter:

host1/Admin(config-ft-track-intf)# no peer track-interface vlan 200

Related Commands

(config-ft-track-interface) track-interface vlan

(config-ft-track-interface) priority

To assign a priority to the interface that the active member is tracking, use the priority command. Use the no form of this command to reset the priority of the interface to the default value of 10.

priority number

no priority number

Syntax Description

number

Priority of the interface tracked by the active member of a fault-tolerant (FT) group. Enter an integer from 0 to 255. The default is 0. Higher values indicate higher priorities.

Command Modes

FT track interface configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

Assign a priority value based on the relative importance of the interface that you are tracking on the active member of an FT group. If the tracked interface goes down, the ACE decrements the priority of the FT group on the active member by the value of the number argument. If the priority of the FT group on the active member falls below the priority of the FT group on the standby member, a switchover occurs where the active member becomes the standby member and the standby member becomes the active member.

Examples

To set a priority of 100 for the interface that you are tracking on the active member of an FT group, enter:

host1/Admin(config-ft-track-intf)# priority 100

To reset the priority of the interface to the default value of 0, enter:

host1/Admin(config-ft-track-intf)# no priority 100

Related Commands

(config-ft-track-interface) peer priority

(config-ft-track-interface) track-interface vlan

To configure the interface that you want the active member to track, use the track-interface vlan command. Use the no form of this command to remove the interface from the tracking process.

track-interface vlan vlan_id

no track-interface vlan vlan_id

Syntax Description

vlan_id

Unique identifier of an existing VLAN that you want to track on the active member of a fault-tolerant (FT) group. Enter an integer from 2 to 4094.

Command Modes

FT track interface configuration mode

Admin and user contexts

Command History

Release	Modification
A1(7)	This command was introduced.

Usage Guidelines

This command has no usage guidelines.

Examples

To configure the VLAN 200 interface for tracking on the active member, enter:

host1/Admin(config-ft-track-intf)# track-interface vlan 200

To remove VLAN 200 from the tracking process, enter:

host1/Admin(config-ft-track-intf)# no track-interface vlan 200

Related Commands

show interface
(config) interface